Dell™ Inspiron™ 1100, 5100, and 5150 Service Manual
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.
Model PP07L and PP08L
June 2003
Rev. A01
Information in this document is subject to change without notice.
© 2003 Dell Computer Corporation. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, and Inspiron are trademarks of Dell Computer Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Computer Corporation
disclaims any proprietary interest in trademarks and trade names other than its own.
Before You Begin
Dell™ Inspiron™ 1100, 5100, and 5150 Service Manual
Preparing to Work Inside the Computer
CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is
not covered by your warranty. Read and follow the safety instructions in the Owner's Manual that came with the computer.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of
your computer's electronic components. You can do so by touching an unpainted metal surface.
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal
mounting bracket. Hold a component such as a microprocessor by its edges, not by its pins.
NOTICE: To avoid damaging the computer, perform the following steps before you begin working inside the computer.
1. Ensure that the work surface is flat and clean to prevent scratching the computer cover.
2. Save any work in progress and exit all open programs.
3. Turn off the computer and all attached devices.
NOTE: Ensure that the computer is off and not in a power management mode. If you cannot shut down the computer using the computer operating
system, press and hold the power button for 4 seconds.
4. Disconnect the computer from the electrical outlet.
5. Close the display and turn the computer upside down on a flat work surface.
NOTICE: To avoid damaging the system board, you must remove the main battery before you service the computer.
6. Slide and hold the battery-bay latch release on the bottom of the computer, and then remove the battery from the bay.
1
2
battery
battery-bay latch release
7. To avoid possible damage to the system board, wait 10 to 20 seconds and then disconnect any attached devices.
8. Disconnect all other external cables from the computer.
9. Remove any installed PC Cards from the PC Card slot.
Recommended Tools
The procedures in this manual require the following tools:
l
l
l
l
l
#1 Phillips screwdriver
¼-inch flat-blade screwdriver
Small plastic scribe
Hex nut driver
Flash BIOS update program CD
Computer Orientation
1
2
3
4
back
right
front
left
Screw Identification
When you are removing and replacing components, photocopy "Screw Identification" as a tool to lay out and keep track of the screws. The placemat provides
the number of screws and their sizes.
Hard Drive Door:
(2 each)
Modem to
System Board:
Optical Drive:
(1 each)
(2 each)
Keyboard
to Computer Base:
Display Assembly
to Back Panel:
Hinge Bracket
to Computer Base:
(4 each)
(2 each)
(4 each)
Display Bezel:
(5 each)
Display Panel:
(8 each)
Display Latch:
(2 each)
Screw Covers (2 each)
Display Bumpers (3 each)
EMI Shield:
(1 each)
Top of Palm Rest to
Computer Base:
Palm Rest to
Base Plastics:
(2 each)
(12 each)
Video Card
to System Board:
Palm Rest to
Battery Bay:
System Board to
Base Plastics:
(2 each)
(1 each)
(3 each, hard drive cage)
(2 each, optical drive cage)
Battery Bay Shield
to System Board:
Left Antenna
to Hard Drive and
Optical Drive Cages
(Inspiron™ 5100 and 5150
only):
(2 each)
(2 each)
Flashing the BIOS
Dell™ Inspiron™ 1100, 5100, and 5150 Service Manual
1. Ensure that the AC adapter is plugged in and that the main battery is installed properly.
2. Insert the BIOS update program CD and turn on the computer.
Follow the instructions that appear on the screen. The computer continues to boot and updates the new BIOS. When the update is complete, the
computer will automatically reboot.
3. Press
4. Press
during POST to enter the system setup program.
to reset the computer defaults.
5. Press
and press
to save configuration changes.
6. Remove the flash BIOS update program CD from the drive and restart the computer.
Microprocessor Module
Dell™ Inspiron™ 1100, 5100, and 5150 Service Manual
Removing the Microprocessor Module
CAUTION: Before performing the following procedures, read the safety instructions in your Owner's Manual.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of
your computer's electronic components. You can do so by touching an unpainted metal surface.
NOTICE: Press and hold the microprocessor down by applying slight pressure to the center of the microprocessor while turning the cam screw to
prevent intermittent contact between the cam screw and microprocessor.
NOTICE: To avoid damage to the microprocessor, hold the screwdriver so that it is perpendicular to the microprocessor when turning the cam screw.
NOTICE: When removing the microprocessor module, pull the module straight up. Be careful not to bend the pins on the microprocessor module.
6. To loosen the ZIF socket, use a small, flat-blade screwdriver and rotate the ZIF-socket cam screw counterclockwise until it comes to the cam stop.
The ZIF-socket cam screw secures the microprocessor to the system board. Take note of the arrow on the ZIF-socket cam screw.
1
2
3
4
ZIF-socket cam screw
ZIF socket
microprocessor module
pin-1 corner of
microprocessor
5
triangle on system board
7. Use a microprocessor extraction tool to remove the microprocessor module.
Installing the Microprocessor Module
NOTICE: Ensure that the cam lock is in the fully open position before seating the microprocessor module. Seating the microprocessor module properly in
the ZIF socket does not require force.
NOTICE: A microprocessor module that is not properly seated can result in an intermittent connection or permanent damage to the microprocessor and
ZIF socket.
1. Align the pin-1 corner of the microprocessor module so that it points to the triangle on the system board, and insert the microprocessor module into the
ZIF socket.
When the microprocessor module is correctly seated, all four corners are aligned at the same height. If one or more corners of the module are higher
than the others, the module is not seated correctly.
NOTICE: Hold the microprocessor down while turning the cam screw to prevent intermittent contact between the cam screw and microprocessor.
2. Tighten the ZIF socket by turning the cam screw clockwise to secure the microprocessor module to the system board.
3. Wipe the thermal grease off of the microprocessor thermal-cooling assembly with a clean paper towel.
4. Squeeze all of the contents of the thermal grease packet (provided with the kit) on to the microprocessor thermal-cooling assembly.
Display
Dell™ Inspiron™ 1100, 5100, and 5150 Service Manual
Display Assembly
CAUTION: Before performing the following procedures, read the safety instructions in your Owner's Manual.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of
your computer's electronic components. You can do so by touching an unpainted metal surface.
5. Close the display.
6. From the back of the computer, remove the two M2.5 x 5-mm screws labeled "circle D."
7. Open the display assembly approximately 180 degrees, and support the display assembly so that it does not open past this position.
8. Remove the two M2.5 x 5-mm screws from each hinge bracket.
1
display assembly
2
3
4
M2.5 x 5-mm screws (4)
hinge brackets (2)
computer base
9. Pull straight up on the pull-tab that is attached to the display-feed flex cable to disconnect the cable from the system board.
10. Lift the display assembly up and out of the computer base.
1
screw covers (2)
display bumpers (3)
2
3
4
5
6
7
M2.5 x 5-mm screws (5)
display bezel
display panel
M2 x 3-mm screws (8)
top cover
display-feed flex cable
Display Bezel
CAUTION: Before performing the following procedures, read the safety instructions in your Owner's Manual.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of
your computer's electronic components. You can do so by touching an unpainted metal surface.
4. Use a plastic scribe to pry the five screw covers out of the screw holes located on the front of the bezel.
5. Remove the five M2.5 x 5-mm screws located on the front of the bezel.
NOTICE: Carefully separate the bezel from the top cover to avoid damage to the bezel.
6. Starting at the bottom of the display panel, use your fingers to separate the bezel from the top cover and lift the inside edge of the bezel away from
the top cover.
Display Panel
Removing the Display Panel
CAUTION: Before performing the following procedures, read the safety instructions in your Owner's Manual.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of
your computer's electronic components. You can do so by touching an unpainted metal surface.
5. Remove the four M2 x 3-mm screws on the each side of the display panel.
6. Lift the display panel out of the top cover.
7. Disconnect the top flex-cable connector from the display panel connector by peeling up the pull-tab and pulling the tab down and away from the display
panel connector.
1
2
3
display panel connector
pull-tab
top flex-cable connector
8. Disconnect the bottom flex-cable connector from the inverter connector on the system board by peeling up the pull-tab and pulling the tab down and
away from the inverter connector.
1
2
inverter connector
bottom flex-cable
connector
3
pull-tab
Installing the Display Panel
1. Connect the top flex-cable connector to the display panel connector.
2. Connect the bottom flex-cable connector to the inverter connector.
3. Lay the display panel in the top cover.
4. Route the display-feed flex cable so that it rests in the notch located in the bottom edge of the top cover.
5. Replace the eight M2 x 3-mm screws that secure the display panel to the top cover.
Display Latch Assembly
Removing the Display Latch Assembly
CAUTION: Before performing the following procedures, read the safety instructions in your Owner's Manual.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of
your computer's electronic components. You can do so by touching an unpainted metal surface.
5. Remove the two M2.5 x 5-mm screws that secure the display latch assembly to the top cover.
6. Lift the display latch assembly up and out of the top cover.
1
2
3
4
5
6
spring
spring hook (display latch)
display latch assembly
M2.5 x 5-mm screws (2)
top cover
spring hook (top cover)
Installing the Display Latch Assembly
1. Attach one end of the spring to the spring hook on the left edge of the display latch, and attach the other end of the spring to the spring hook in the
top cover.
2. Align the screw holes in the display latch assembly with the screw holes in the top cover.
3. Replace the two M2.5 x 5-mm screws that secure the display latch assembly to the top cover.
Hard Drive
Dell™ Inspiron™ 1100, 5100, and 5150 Service Manual
Removing the Hard Drive
CAUTION: If you remove the hard drive from the computer when the drive is hot, do not touch the metal housing of the hard drive.
CAUTION: Before working inside your computer, read the safety instructions in your Owner's Manual.
NOTICE: To prevent data loss, shut down your computer before removing the hard drive. Do not remove the hard drive while the computer is on, in
standby mode, or in hibernate mode.
NOTICE: Hard drives are extremely fragile; even a slight bump can damage the drive.
NOTE: Dell does not guarantee compatibility or provide support for hard drives from sources other than Dell.
2. Turn the computer over, and remove the two M2.5 x 5-mm hard drive screws.
1
2
M2.5 x 5-mm screws (2)
hard drive
NOTICE: When the hard drive is not in the computer, store it in protective antistatic packaging. See "Protecting Against Electrostatic Discharge" in your
Owner's Manual.
3. Slide the hard drive out of the computer.
Installing the Hard Drive
1. Remove the new drive from its packaging.
Save the original packaging for storing or shipping the hard drive.
NOTICE: Use firm and even pressure to slide the drive into place. If you use excessive force, you may damage the connector.
2. Insert the drive into the bay, and push the hard drive until it is fully seated in the bay.
3. Replace and tighten the two M2.5 x 5-mm screws.
4. Use the Operating System CD to install the operating system for your computer.
5. Use the Drivers and Utilities CD to install the drivers and utilities for your computer.
Keyboard
Dell™ Inspiron™ 1100, 5100, and 5150 Service Manual
Removing the Keyboard
CAUTION: Before working inside your Dell™ computer, read the safety instructions in your Owner's Manual.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of
your computer's electronic components. You can do so by touching an unpainted metal surface.
2. Use a small flat-blade screwdriver or plastic scribe to lift the notched right edge of the hinge cover, and pry the cover loose from the hinges and
computer base.
1
2
notched edge
hinge cover
3. Lift the hinge cover up and away from the hinges and computer base.
4. Remove the four M2 x 3-mm keyboard screws.
1
2
M2 x 3-mm screws (4)
keyboard
NOTICE: The keycaps on the keyboard are fragile, easily dislodged, and time-consuming to replace. Be careful when removing and handling the
keyboard.
5. Lift the top of the keyboard out of the computer base, and pull the keyboard out at an angle (towards the display). Rest the keyboard face down on
the palm rest.
6. Grasp the keyboard flex cable near the connector, and pull up on the flex cable to disconnect it from the interface connector on the system board.
1
2
keyboard connector
interface connector
7. Remove the keyboard from the computer base.
Installing the Keyboard
NOTICE: To avoid damage to the connector pins, press the keyboard connector evenly into the interface connector on the system board, and do not
reverse the keyboard connector.
1. Connect the keyboard connector of the replacement keyboard to the interface connector on the system board.
1
2
3
4
securing tabs (4)
keyboard connector
interface connector
M2 x 3-mm screws (4)
2. Insert the four securing tabs on the keyboard into their respective slots in the palm rest, and lower the keyboard into the computer base.
Ensure that all four securing tabs are engaged before trying to completely seat the keyboard.
3. Replace the four M2 x 3-mm keyboard screws.
4. To replace the hinge cover, first insert the left side of the hinge cover into the notches. Snap down the hinge cover, and ensure that it is flush with the
palm rest.
EMI Shield, Video Card, and Palm Rest
Dell™ Inspiron™ 1100, 5100, and 5150 Service Manual
EMI Shield
CAUTION: Before performing the following procedures, read the safety instructions in your Owner's Manual.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of
your computer's electronic components. You can do so by touching an unpainted metal surface.
3. Pull up on the pull-tab that is attached to the display-feed flex cable connector to remove the connector from the system board.
4. Remove the one M2.5 x 8-mm screw that secures the EMI shield to the system board, and pull the EMI shield out of the computer base.
Video Card
Removing the Video Card
CAUTION: Before performing the following procedures, read the safety instructions in your Owner's Manual.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of
your computer's electronic components. You can do so by touching an unpainted metal surface.
4. Remove the two M2.5 x 8-mm screws that secure the video card to the system board.
1
2
3
pull-tab
video card
M2.5 x 8-mm screws (2)
5. Pull straight up on the attached pull-tab to lift the video card off of the system board.
Installing the Video Card
1. Align the posts on the video card with the screw holes in the system board.
2. Press down on the two areas on the video card that are labeled "PUSH" until you feel the video card click into place.
3. Replace the two M2.5 x 8-mm screws.
Palm Rest
CAUTION: Before performing the following procedures, read the safety instructions in your Owner's Manual.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of
your computer's electronic components. You can do so by touching an unpainted metal surface.
7. Turn the computer over and remove the twelve M2.5 x 8-mm screws (not labeled).
8. Remove the M2.5 x 4-mm screw from the battery bay.
9. Turn the computer back over and remove the two M2.5 x 5-mm screws from the top of the palm rest.
10. Disconnect the touch pad connector from the system board.
NOTICE: Carefully separate the palm rest from the base plastics to avoid damage to the palm rest.
11. Starting at the back center of the palm rest, use your fingers to separate the palm rest from the base plastics by lifting the inside edge of the palm rest.
Speakers
Dell™ Inspiron™ 1100, 5100, and 5150 Service Manual
Removing the Speakers
CAUTION: Before performing the following procedures, read the safety instructions in your Owner's Manual.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of
your computer's electronic components. You can do so by touching an unpainted metal surface.
The speakers are located on the left and right corners of the front of the base plastics. Take note of the speaker cable routing so that you can replace the
cables properly under or between their routing clips.
8. Disconnect the speaker connector from the system board.
1
2
3
4
left speaker
routing clips (3)
speaker connector
right speaker
NOTICE: Remove the speaker cables from their routing clips with care to avoid damaging the cables.
9. Remove the speaker cables from under or between their routing clips.
NOTICE: Handle the speakers with care to avoid damaging them.
10. Remove the speakers by pulling them straight up and out of the base plastics.
Installing the Speakers
1. Slide the speakers down into the base plastics.
NOTICE: Ensure that the speaker cables are under or between their routing clips.
NOTE: Speakers face out in the base plastics holders.
NOTE: The right speaker cable is longer than the left speaker cable.
2. Route the speaker cables under or between their routing clips.
3. Connect the speaker connector to the system board.
System Board
Dell™ Inspiron™ 1100, 5100, and 5150 Service Manual
Removing the System Board
CAUTION: Before performing the following procedures, read the safety instructions in your Owner's Manual.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of
your computer's electronic components. You can do so by touching an unpainted metal surface.
The system board's BIOS chip contains the Service Tag sequence, which is also visible on a barcode label on the bottom of the computer. The replacement kit
for the system board includes a CD that provides a utility for transferring the Service Tag sequence to the replacement system board.
15. Remove the two M2.5 x 5-mm screws from the battery bay shield, and remove the shield.
1
2
3
battery bay
battery bay shield
M2.5 x 5-mm screws (2)
16. Remove the three M2.5 x 5-mm system board screws from the hard drive cage.
17. Remove the two M2.5 x 5-mm system board screws from the optical drive cage.
1
hard drive cage
2
3
4
M2.5 x 5-mm screws (3)
optical drive cage
M2.5 x 5-mm screws (2)
18. Remove the two M2.5 x 5-mm screws that secure the left antenna to the hard drive and optical drive cages (Inspiron™ 5100 and 5150 only).
1
optical drive cage
M2.5 x 5-mm screws (2)
left antenna
2
3
4
hard drive cage
19. Remove the two hex nuts that secure the video connector to the base plastics.
20. Lift the front of the system board out and away from the base plastics.
Installing the System Board
1. Insert the video connector on the replacement system board through the back of the base plastics.
2. Replace the two hex nuts that secure the video connector to the base plastics.
3. Replace the two M2.5 x 5-mm screws that secure the left antenna, which is located between the hard drive and optical drive cages, to the system
board (Inspiron™ 5100 and 5150 only).
4. Replace the two M2.5 x 5-mm screws that secure the optical drive cage to the system board.
5. Replace the three M2.5 x 5-mm screws that secure the hard drive cage to the system board.
6. Replace the battery bay shield, and reinstall the two M2.5 x 5-mm screws that secure the shield to the system board.
NOTICE: Before you replace the microprocessor thermal-cooling assembly, wipe the thermal grease off of the assembly with a clean paper towel.
Squeeze all of the contents of the thermal grease packet (provided with the kit) on to the microprocessor thermal-cooling assembly.
14. Replace the Mini PCI card, modem, and memory module(s) that you removed from the old system board.
17. Insert the battery into the battery bay.
18. Connect the AC adapter to the computer and to an electrical outlet.
NOTICE: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may result in
damage to the computer.
NOTE: After replacing the system board, enter the computer Service Tag sequence into the BIOS of the replacement system board.
19. Turn on the computer.
20. Insert the CD that accompanied the replacement system board into the appropriate drive, and turn on the computer. Follow the instructions on the
screen.
System Components
Dell™ Inspiron™ 1100, 5100, and 5150 Service Manual
CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is
not covered by your warranty.
NOTICE: Unless otherwise noted, each procedure in this document assumes that a part can be replaced by performing the removal procedure in
reverse order.
1
2
3
4
display
11 base plastics
12 battery
display-feed flex cable
hinge cover
keyboard
13 CD or DVD drive
14 left antenna (Inspiron™
5100 and 5150 only)
5
6
palm rest
15 hard drive
microprocessor thermal-
cooling assembly
16 system board
7
8
EMI shield
17 modem
battery bay shield
18 Mini PCI card (Inspiron
5100 and 5150 only)
9
microprocessor
19 video card (Inspiron
5100 and 5150 only)
10 speakers
Microprocessor Thermal-Cooling Assembly
Dell™ Inspiron™ 1100, 5100, and 5150 Service Manual
Removing the Microprocessor Thermal-Cooling Assembly
CAUTION: Before performing the following procedures, read the safety instructions in your Owner's Manual.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of
your computer's electronic components. You can do so by touching an unpainted metal surface.
5. Disconnect the fan power cable from the system board.
6. Loosen in consecutive order the four captive screws, labeled "1" through "4," that secure the microprocessor thermal-cooling assembly to the system
board.
1
2
captive screws (4)
fan power-cable
connector
7. Pull up the microprocessor thermal-cooling assembly by the pull-tab to lift the assembly out of the system board.
Installing the Microprocessor Thermal-Cooling Assembly
NOTICE: Before you install the replacement microprocessor thermal-cooling assembly, remove the mylar that covers the thermal grease on the
assembly.
1. If you are installing a replacement microprocessor thermal-cooling assembly, remove the mylar that covers the thermal grease on the assembly. If you
are installing the assembly that you removed in the previous section:
a. Wipe the thermal grease off of the microprocessor thermal-cooling assembly with a clean paper towel.
b. Squeeze all of the contents of the thermal grease packet (provided with the kit) on to the microprocessor thermal-cooling assembly.
2. Place the back of the microprocessor thermal-cooling assembly under the palm rest, and lower the assembly onto the system board.
3. Connect the fan power cable to the system board.
4. Tighten the four captive screws, labeled "1" through "4," in consecutive order.
Dell™ Inspiron™ 1100, 5100, and 5150 Service Manual
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.
Information in this document is subject to change without notice.
© 2003 Dell Computer Corporation. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, and Inspiron are trademarks of Dell Computer Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Computer Corporation
disclaims any proprietary interest in trademarks and trade names other than its own.
Model PP07L and PP08L
June 2003
Rev. A01
Memory, CD or DVD Drive, Modem, and Mini PCI Card
Dell™ Inspiron™ 1100, 5100, and 5150 Service Manual
Memory
Removing the Memory Modules
CAUTION: Before working inside your Dell™ computer, read the safety instructions in your Owner's Manual.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of
your computer's electronic components. You can do so by touching an unpainted metal surface.
NOTE: Memory modules purchased from Dell are covered under your computer warranty.
2. Turn the computer over, loosen the captive screw (labeled "circle M") in the memory module cover, and lift the cover away from the computer.
1
2
captive screw
memory module cover
3. Use your fingertips to carefully spread apart the securing clips on each end of the memory module connector until the module pops up.
4. Remove the module from the connector.
1
2
memory module
securing clips
Installing the Memory Modules
NOTE: If the memory module is not installed properly, the computer may not boot properly. No error message indicates this failure.
1. Align the notch in the module edge connector with the tab in the connector slot.
2. Slide the module firmly into the slot at a 45-degree angle, and rotate the module down until it clicks into place. If you do not feel the click, remove the
module and reinstall it.
3. Replace the cover and tighten the captive screw.
NOTICE: If the memory module cover is difficult to close, remove the module and reinstall it. Forcing the cover to close may damage your computer.
4. Insert the battery into the battery bay, or connect the AC adapter to your computer and an electrical outlet.
5. Turn on the computer.
As the computer boots, it detects the additional memory and automatically updates the system configuration information.
To confirm the amount of memory installed in the computer, click the Start button, click Help and Support, and then click Computer Information.
CD or DVD Drive
Removing the CD or DVD Drive
CAUTION: Before working inside your Dell™ computer, read the safety instructions in your Owner's Manual.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of
your computer's electronic components. You can do so by touching an unpainted metal surface.
2. Turn the computer over, and remove the M2.5 x 8-mm screw labeled "O" next to the memory module cover.
3. Loosen the captive screw (labeled "circle M") in the memory module cover, and lift the cover away from the computer.
1
2
captive screw
memory module cover
4. Press the lever next to the memory module connectors in the direction of the arrow on the lever (towards the drive) to release the drive.
1
2
3
lever
CD or DVD drive
M2.5 x 8-mm screw
labeled "O"
5. Pull the drive out of the bay.
Installing the CD or DVD Drive
1. Slide the new drive into the bay until the drive is fully seated.
2. Replace the memory module cover and tighten the captive screw.
3. Replace the M2.5 x 8-mm screw next to the memory module cover.
Modem
Removing the Modem
CAUTION: Before working inside your Dell™ computer, read the safety instructions in your Owner's Manual.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of
your computer's electronic components. You can do so by touching an unpainted metal surface.
2. Turn the computer over, loosen the captive screw (labeled "circle C") in the modem/Mini PCI card cover, and lift the cover away from the computer.
1
2
captive screw
modem/Mini PCI card
cover
3. Remove the two M2 x 3-mm screws securing the modem to the system board, and set them aside.
4. Pull straight up on the attached pull-tab to lift the modem out of its connector on the system board and disconnect the modem cable.
1
2
3
4
modem cable connector
pull-tab
modem cable
M2 x 3-mm screws (2)
Installing the Modem
1. Connect the modem cable to the modem.
NOTICE: The cable connectors are keyed for correct insertion; do not force the connections.
2. Align the modem with the screw holes, and press the modem into the connector on the system board.
3. Install the two M2 x 3-mm screws to secure the modem to the system board.
4. Replace the cover and tighten the captive screw.
Mini PCI Card (Inspiron™ 5100 and 5150 Only)
Removing the Mini PCI Card
CAUTION: Before working inside your Dell™ computer, read the safety instructions in your Owner's Manual.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of
your computer's electronic components. You can do so by touching an unpainted metal surface.
2. Turn the computer over, loosen the captive screw (labeled "circle C") in the modem/Mini PCI card cover, and lift the cover away from the computer.
1
2
captive screw
modem/Mini PCI card
cover
3. Disconnect the Mini PCI card from the attached cables.
1
2
3
4
antenna cables
metal securing tabs (2)
Mini PCI card connector
Mini PCI card
4. Use your fingertips to carefully spread apart the securing taps on each end of the Mini PCI card connector until the card pops up.
5. Lift the Mini PCI card out of its connector.
Installing the Mini PCI Card
NOTICE: To avoid damaging the Mini PCI card, never place cables on top of or under the card.
NOTICE: The connectors are keyed to ensure correct insertion. If you feel resistance, check the connectors and realign the card.
1. Align the Mini PCI card with the connector at a 45-degree angle, and press the Mini PCI card into the connector until it clicks.
1
2
3
antenna cables
Mini PCI card connector
Mini PCI card
2. Connect the antenna cables to the Mini PCI card.
NOTE: To prevent damage to the antenna cables, carefully fold the cables under the Mini PCI card before replacing the cover.
3. Replace the cover and tighten the captive screw.
|
