Cecilware WHIPPER User Manual

GOURMET HOT BEVERAGE DISPENSER  
Models:  
ICAP1  
ICAP1-P  
ICAP-MINI  
WHIPPER  
WHIPPER MINI  
OPERATIONAL MANUAL  
Specifications  
Installation & Operating Instructions  
Adjustments  
Care & Maintenance  
Trouble Shooting Guide  
Wiring Diagram  
Parts List  
THIS EQUIPMENT IS TO BE INSTALLED TO COMPLY WITH  
THE APPLICABLE FEDERAL, STATE, OR LOCAL PLUMBING  
CODES HAVING JURISDICTION.  
IN ADDITION:  
1. A QUICK DISCONNECT WATER CONNECTION OR  
ENOUGH EXTRA COILED TUBING (AT LEAST 2X  
THE DEPTH OF THE UNIT) SO THAT THE MACHINE  
CAN BE MOVED FOR CLEANING UNDERNEATH.  
2. AN APPROVED BACK FLOW PREVENTION DEVICE,  
SUCH AS A DOUBLE CHECK VALVE TO BE INSTALLED  
BETWEEN THE MACHINE AND THE WATER SUPPLY.  
Cecilware sells value...  
Worldwide.  
43-05 20th Avenue, Long Island City, NY 11105 · 718-932-1414  
FAX:  
· 718-932-7860  
NA64A 6/99  
INSTALLATION REQUIREMENTS for ICAP1 B LD and WHIPPER B:  
THIS EQUIPMENT IS TO BE INSTALLED TO COMPLY WITH THE APPLICABLE FEDERAL, STATE, OR LOCAL PLUMBING CODES  
HAVING JURISDICTION. IN ADDITION:  
1. A QUICK DISCONNECT WATER CONNECTION OR ENOUGH EXTRA COILED TUBING (AT LEAST 2X THE  
DEPTH OF THE UNIT) SO THAT THE MACHINE CAN BE MOVED FOR CLEANING UNDERNEATH.  
2. AN APPROVED BACK FLOW PREVENTION DEVICE, SUCH AS A DOUBLE CHECK VALVE TO BE INSTALLED  
BETWEEN THE MACHINE AND THE WATER SUPPLY.  
INSTALLATION:  
1. Flush inlet water line thoroughly before connecting. If pipe sealant is necessary, teflon tape is commended.  
2. Connect water line to the 1/4” flare fitting located at rear of the unit. A shutoff valve in the water supply line is advisable.  
3. Check that heater switch is in the OFF position. Switch is located below DOOR ASSEMBLY lower right side corner.  
4. Turn on water. Check water line and fittings for leaks.  
5. Plug the power cord into a grounded 120 volt, 60 Hz 15 Amp outlet, Single use. Press and hold Rinse Button until water  
flows through mixing chamber. It will take 2 to 4 minutes to fill the tank.  
6. Fill hopper with DRY* powdered cocoa mix or cappuccino product. See filling instructions.  
7. Turn heater switch on and allow 10 to 15 minutes for water to heat.  
8. Push on Dispensing Button and check the operation of the hopper. A grinding noise will be heard if not properly engaged.  
Go to Troubleshooting Guide.  
9. Push on Dispensing Button and check the operation of the mixing chamber (for ICAP1 & Whipper ).  
A scratching noise will be heard if whipper blade is not properly aligned. Go to Troubleshooting Guide.  
10. Push Dispensing Button and check drink taste.  
If adjustments are needed, see “Adjustments”.  
DISPENSER OPERATION  
FILLING  
1. Open Front Door.  
2. Lift Top Cover.  
3. Fill hopper to desired level with DRY*  
Powdered cocoa mix or cappuccino.  
Do not overfill or pack product down when filling.  
4. Close Top Cover and Door.  
DISPENSING  
1. Place cup under mixing chamber spout.  
2. a) For Manual Units (without Timer):  
Press and hold push button until cup is approximately 2/3 full.  
b) For Automatic Units (with Timer):  
Press and release push button. Cup will fill to size set on Timer.  
3. Remove cup when flow from mixing  
chamber has stopped completely.  
*Moist product will clog hopper and the unit will not operate  
properly.  
Illustration No. 2 – (ICAP 1 B LD & WHIPPER B shown)  
3
START UP INSTRUCTIONS FOR ICAP1 POUROVER CAPPUCCINO DISPENSER – see ill. 3  
I. INSTALLATION INSTRUCTIONS  
This equipment is to be installed to comply with the applicable Federal, State, or local plumbing codes having jurisdiction.  
In addition:  
1.  
A quick disconnect water connection or enough extra coiled tubing (at least 2x the depth of the unit) so that the machine  
can be moved for cleaning underneath.  
2.  
An approved back flow prevention device, such as a double check valve to be installed between the machine and the wa-  
ter supply.  
The ICAP1 POUROVER beverage dispenser is equipped with a 3/4” Water Inlet Valve (¼" to 3/4” adapter supplied with the  
unit) which is located on the right side in the back of the base (when looking at the machine from the front).  
HIGHLY RECOMMENDED: A WATER SHUT-OFF VALVE and A WATER FILTER, preferably a combination Charcoal/Phosphate  
Filter, to remove odors and inhibit lime and scale build up in the machine.  
Note: In areas with extremely hard water, a water softener must be installed in order to prevent a malfunctioning of the equip-  
ment and in order not to void the warranty.  
After the machine has been unpacked and placed on a counter, pull out the drip tray and splash guard.  
It should contain the following: A Set of 4 Adjustable Leveling Legs & Water Inlet Fitting.  
Connect the ¼" dia. copper waterline to the ¼" flare water inlet fitting of the valve.  
Caution: Do not plug into power outlet yet. Make sure the Heater Switch is OFF (Toggle Down).  
II. PRIMING - MANUAL/BOTTLE POUROVER (Toggle UP, Water Selection Switch, on the back panel)  
1. Do NOT plug into power outlet yet.  
2. Make sure Heater Switch is in the OFF position, located in back of machine.  
3. Fill reservoir tank (top) with 2 gallons of water, wait about 3 minutes for water to fill Heating Tank below.  
Refill Top Reservoir Tank with another 2 gallons of water. The unit will NOT dispense unless the Top Reservoir Tank is at  
least 1/2 full. So keep Reservoir Tank full.  
Note: The unit has a Float (item 3, Ill. 8) inside the Reservoir Tank, which stops the machine from dispensing  
when the Reservoir Tank is low.  
4. Plug into power outlet.  
5. Turn Heater Switch ON.  
6. Allow 10 to 15 minutes for water to reach dispense temperature of 190°F. Heater Indicator Light (red) goes ON when  
heater is on (see lower front panel).  
7. Fill hopper with product.  
8. Place cup under dispenser.  
9. Push and hold Dispense Button (green) until water flows from mixing chamber.  
10. Machine is primed and ready to go.  
III. PRIMING INSTRUCTIONS FOR ICAP1 POUROVER  
PRIMING - AUTOFILL (Toggle Down,Water Selection Switch, on the back panel)  
1. Plug into power outlet.  
2. Turn Heater Switch ON.  
3. Allow 10 to 15 minutes for water to reach dispense temperature of 190°F.  
Heater Indicator Light (red) goes ON when heater is on (see lower front panel).  
4. Fill hopper with product.  
5. Place cup under dispenser.  
6. Push and hold Dispense Button (green) until water flow s from mixing chamber  
7. Machine is primed and ready to go.  
4
IV. POUROVER-PORTABLE BOTTLE OPERATION (Toggle UP, Water Selection Switch, on the back panel)  
UNIT CAN BE OPERATED WITH A 3 GALLONS CAPACITY FRESH WATER BOTTLE.  
TO OPERATE WITH PORTABLE BOTTLE, proceed AS FOLLOWS:  
1. Remove Reservoir Tank Cover.  
2. Make sure that Reservoir Tank is only 1/2 full or empty, to prevent water splillage.  
To remove excess water push dispense button.  
3. Fill bottle with water .  
4. Invert bottle into reservoir tank in one motion to minimize spillage.  
5. Remove and refill bottle when “REFILL“ light is ON.  
NOTE: REFILL LIGHT, ON THE FRONT DOOR PANEL, WILL GO ON, WHICH INDICATES THAT THE WATER TANK MUST  
BE REFILLED. WHEN REFILL LIGHT GOES ON, THE UNIT WILL NOT DISPENSE UNTIL TANK IS FILLED WITH WATER.  
REFILLING WITH HOT TAP WATER WILL SHORTEN HEAT UP TIME.  
V. NORMAL OPERATION  
(POUROVER AND AUTOREFILL)  
1. Place a 6 oz. or larger cup under dispense nozzle,  
then press and hold dispense switch (green) for 6  
seconds.  
The machine will dispense water at the rate of 1 oz.  
per second. Repeat it several times to check for con-  
sistent output.  
BOTTLE  
2. While the tank is heating up, remove the hopper,  
load with product and reposition it back in the ma-  
chine.  
RESERVOIR  
COVER  
When Heater Light goes OFF, the tank has reached  
its brew temperature and the machine is ready to  
begin dispensing the first cup of Cappuccino.  
RESERVOIR  
TANK  
VI. WATER FLOW and  
DRINK STRENGTH ADJUSTMENTS  
THE UNIT IS FACTORY ADJUSTED TO DISPENSE  
WATER AND POWDER AT THE RATE OF 1.0 oz/  
sec.  
TO INCREASE OR DECREASE FLOW, PROCEED AS  
FOLLOWS:  
1. Remove left side panel and locate Dispense Valve  
Flow Adjuster on top of Heated Tank.  
2. Locate Flow Adjustment Screw (white) on Dispense  
Valve.  
3. Rotate Adjustment Screw Counterclockwise to IN-  
CREASE flow rate.  
WATER FLOW  
ADJUSTMENT,  
SCREW ON  
DISPENSE  
INDICATOR  
LIGHT- RED  
"REFILL TANK  
WHEN ON"  
DISPENSE  
VALVE  
4. Rotate Clockwise to DECREASE flow rate.  
BUTTON  
When making strength adjustments, do not adjust  
by more than 1/4 turn at a time, without checking  
drink strength (ratio of water to powder).  
HOT WATER TANK  
DRIP TRAY  
Illustration No. 3 – ICAP 1 B LD POUROVER  
5
DRINK STRENGTH ADJUSTMENTS  
NOTE: The unit has been factory preset to deliver water at 1 oz. per second  
A. TO ADJUST PRODUCT THROW (ILL # 4)  
1. Open Door Assembly and remove Steam Deflector  
by pulling it forward.  
2. To make adjustment use a screwdriver with 1/2 inch  
wide blade. Engage product adjuster as shown below  
and turn as follow.  
3. Turn clockwise to increase drink strength or  
counter-clockwise to reduce it.  
Check drink strength after every half a turn.  
If after maximum adjustment, drink taste is not as  
desired proceed to adjust the water flow according to  
procedure B below.  
Illustration No. 4 – Product adjuster  
4. Re-install Steam Deflector.  
B. TO ADJUST WATER FLOW RATE (ILL. # 5)  
1. Remove right hand side cover of the unit.  
(looking at the unit from the front)  
2. Locate Flow Adjustment Key inside unit mounted  
above water valve.  
3. Engage Flow Adjustment Key into Flow Controller  
and rotate counterclockwise to decrease  
and clockwise to increase drink strength.  
When making strength adjustments, do not turn  
Adjustment Key more than 1/8” at a time without  
checking drink strength.  
4. Return Adjustment Key back into keyholder.  
If after maximum adjustment, drink taste is still not  
strong as desired, take auger spring out of the hopper and re-  
move the product adjuster.  
Illustration No. 5 – Water Inlet Valve  
C. DRINK SIZE ADJUSTMENT (ILL. # 6)  
(AUTOMATIC UNITS - WITH TIMER)  
1. Remove right side panel.  
2. Turn knob on Timer right to increase or left to decrease drink size.  
The number 6 on the Timer indicates approximate drink size at a  
factory setting of 1 oz./sec. flow rate.  
3. Press push button and check drink size. Repeat if  
necessary, until desired drink size is dispensed.  
4. Replace the side panel.  
Illustration No 6 - Timer  
6
CLEANING INSTRUCTIONS  
ICAP1 B LD (with Lit Door)  
WHIPPER B (without Lit Door)  
DAILY:  
TOP COVER  
1. Wipe exterior of dispenser with a soft damp cloth.  
Deflector setup by pulling forward.  
CLEANING INSTRUCTIONS  
NA62C  
2. Disengage Product Hopper by lifting straight up,  
while retaining in the upright position.  
3. Remove Mixing Chamber by turning Counterclockwise  
and pulling forward.  
PRODUCT  
HOPPER ASS'Y  
A. Remove Mixing Chamber Insert by pulling up.  
B. Remove Mixing Chamber Extension by pulling down.  
STEAM  
DEꢀLECTOR  
4. Remove Mixer Blade by pulling forward.  
PRODUCT SHUTE  
MIXING  
CHAMBER  
INSERT  
5. Wash Grill, Mixer Blade, Insert, Extension, and Mixing  
Chamber with a mild detergent.  
MIXING  
CHAMBER  
6. Wipe upper compartment with a damp cloth.  
7. Replace all parts including Hopper.  
HEATER  
SWITCH  
RINSE  
SWITCH  
MIXING  
CHAMBER  
EXTENSION  
GRILL  
DRIP TRAY  
DRIP TRAY BRACKET  
8. Dry thoroughly before reloading with product.  
MIXER BLADE  
MIXING CHAMBER MOUNT  
SLINGER DISC  
CLEANING INSTRUCTIONS  
ICAP MINI B LD (with Lit Door)  
MINI WHIPPER B (without Lit Door)  
DAILY:  
1. Wipe exterior of dispenser with a soft damp cloth.  
Deflector setup by pulling forward.  
TOP COVER  
CLEANING INSTRUCTIONS  
NB04A  
2. Wash Drip Tray with hot water.  
3. 0lush Mixing Chamber by depressing Rinse Button  
approximately 10 seconds.  
WEEKLY:  
HOPPER ASS'Y  
NOTE: IN VERY HIGH VOLUME LOCATIONS, THIS  
PROCEDURE SHOULD BE DONE TWICE A WEEK.  
STEAM  
DEꢀLECTOR  
PRODUCT GUIDE  
1. Open Top Cover, Door Assembly, and remove Steam  
Deflector setup by pulling forward.  
MIXING  
CHAMBER  
EXTENDER  
RINSE  
SWITCH  
2. Disengage Hopper by lifting straight up,  
while retaining in the upright position.  
MIXING  
CHAMBER  
WING NUT  
3. Remove Mixing Chamber by unscrewing wing nuts.  
4. Wash all components after removing.  
GRILL  
DRIP TRAY  
DRIP TRAY BRACKET  
OPTIONAL  
SEAL (GASKET)  
HEATER  
SWITCH  
MIXING CHAMBER PLATE  
MIXING CHAMBER SPACER  
5. Wipe upper compartment with a damp cloth.  
6. Replace all parts including Hopper.  
7. Dry thoroughly before reloading with product.  
Illustration No. 7  
7
TROUBLESHOOTING PROCEDURE  
WARNING: To reduce the risk of electrical shock unplug the dispenser power cord before repairing or replacing any  
internal components of the unit. Before any attempt to replace a component be sure to check all electrical  
TROUBLE  
Light Display does not go on. a) Dispensing unit unplugged  
No power b) No power from terminal block  
No water when Rinse Switch a) Water supply off  
PROBABLE CAUSE  
REMEDY  
a) Reconnect dispensing unit  
b) Check the terminal block for loose wire  
a)Turn on water  
is depressed  
b) Clogged inlet screen (water valve)  
b) Disconnect water line and clean inlet screen  
No product when Dispense a) No product in hopper  
a) Add product if auger spring is moving  
b) Engage hopper to auger motor’s gear  
Replace damaged coupling if needed  
Check connections of motor, relay and/or  
switch, if needed replace such component.  
d) Clean hopper and dry thoroughly  
Button is depressed  
b) Auger spring not working  
c) Inoperative auger motor  
d) Hopper outlet clogged  
a) Leaking inlet water valve  
Water does not shut off  
a) Clean and check all fittings of water valve.  
Replace water inlet valve  
b) Malfunctioning Timer  
c) Inoperative dispense switch  
b) Replace Timer (automatic units only)  
c) Check switch connections. Replace dispense switch  
Drink too strong  
Drink too weak  
a) Water flow too low  
b) Product throw too high  
a) No product in hopper  
b) Product throw too low  
a) Adjust water flow (see To Adjust Water Flow Rate)  
b) Adjust product throw (see To Adjust Product Rate))  
a) Add product  
b) Adjust product throw (see To Adjust Product Rate)  
Water drips from mixing  
chamber  
a) Temperature too high  
b) Leaking inlet water valve  
c) Too much water in tank’s  
a) Adjust the thermostat accordingly  
b) Check fittings, if needed replace water valve  
c) Remove tank top and clean holes in inner  
Cold drink  
a) No hot water  
a) Allow tank to heat  
b) Run out of hot water  
c) Tank does not heat up  
b) Allow tank to heat after filling  
c) Check for loose wire on either thermostat  
or heating element. Replace either or  
Drink not whipped  
a) No whipper blade  
a) Replace whipper blade  
b) Whipper blade stuck  
b) Check blade alignment, if needed replace  
blade and mixing chamber  
c) Inoperative whipper motor  
c) Replace whipper motor  
Noise coming from mixing  
chamber  
Whipper blade not properly aligned  
Check blade alignment, if needed replace blade and mix-  
ing chamber  
Light Display does not go on Defective light bulb and/or ballast.  
Check for loose wire or properly plugged light bulb.  
Grinding noise coming from Hopper not properly engaged  
unit  
Check the mating between the auger motor’s gear and  
hopper’s coupling  
Dispenser repeats cycle.  
a) Malfunctioning Timer.  
a) Replace Timer (automatic units only)  
b) Malfunctioning Dispense Switch  
8
DESCRIPTION AND LOCATION Oꢀ COMPONENTS  
ICAP1 B LD (with lit door) & WHIPPER B (without lit door)  
Illustration No. 8  
9
COMPONENTS IDENTIFICATION  
ITEM DESCRIPTION  
P/N  
ITEM DESCRIPTION  
P/N  
1
2
3
4
5
6
7
8
9
TANK TOP ASSY  
SILICONE TUBING  
97127  
77184  
97122  
73277  
RE81A  
97198  
20039  
97131  
G0140  
07059  
03051  
97293  
59024  
36 SLINGER DISC  
37 "O" RING  
38 MIXING CHAMBER MOUNT  
39 MIXER BLADE  
40 MIXING CHAMBER EXTENDER TUBE  
41 MIXING CHAMBER  
42 MIXING CHAMBER INSERT  
43 LAMP HOLDER MOUNTING BRACKET (lit door)  
44 BALLAST (for lit door only)  
45 PRODUCT SWITCH  
46 LAMP SOCKET - LEVITTON ( for lit door only)  
47 FLOURESCENT LAMP 9W ( for lit door only)  
48 DOOR WELDMENT ASSY - ICAP 1 B LD (w/lit door)  
83034  
?
DISCHARGE TUBE ASSY  
DISCHARGE TUBE BRACKET  
NOZZLE BRACKET  
TANK BAFFLE ASSY  
TANK BAFFLE SEAL  
83033  
90230  
77184  
95001  
83036  
RE52A  
CE221  
L455C  
44496  
L024A  
RC53Q  
TANK CLAMP ASSY  
HEATER ELEMENT 1750W 120V  
10 WASHER, HEATER ELEMENT  
11 NUT HEATER ELEMENT  
12 TANK LIMIT  
13 HI-LIMIT TEMPERATURE CONTROL  
14 ELBOW, MALE 1/8 NPT X 1/4  
15 CONTROL THERMOSTAT  
16 TOP FRONT COVER  
09246  
59016  
RC42C  
K435C  
49 AUGER MOTOR BRACKET  
50 AUGER MOTOR 115V  
51 SUPPORT PLATE F/AUGER MOTOR  
52 GEAR AUGER DRIVE MOTOR GEAR, PLASTIC  
73272  
52037  
90209  
90208  
17 HOSE BARB FITTING  
18 ADJ. VALVE ASSY #H5107 NPT  
19 HOSE NUT  
20 WATER VALVE INLET ASSY  
K415A  
95101  
L477A  
44242  
58017  
58019  
B135A  
B129A  
RE80Q  
M034C  
92007  
53 O RING  
54 CARTRIDGE HEATER 20W  
55 HEAT DUCT  
56 PRODUCT DISPENSER ADAPTER  
57 STEAM DEFLECTOR  
20015  
87024  
97135  
CD70C  
90272  
21 POWER CORD  
22 TIMER, OPTIONAL - (for automatic units only) 120v  
TIMER, IPTIONAL - (for automatic units only) 220v  
23 TERMINAL BLOCK SINGLE  
24 RELAY (for automatic only) 120v  
25 BODY FRAME WELDMENT ASSY  
26 Legs, set 2.5" BLK  
58 RESTRICTOR  
92173  
34007  
71001  
95116  
90211  
59 RESTRICTOR RETAINER  
60 PRODUCT ADJUSTER  
61 AUGER SPRING  
27 STUD DRIPTRAY  
62 AUGER DRIVE COUPLING, PLASTIC  
28 DRIP TRAY PAN  
29 GRILL  
30 DRIP TRAY BRACKET (HOLDER )(OPTIONAL)  
31 RINSE SWITCH  
32 HEATER SWITCH  
75060  
75015  
RE73A  
56039  
L299C  
63 HOPPER & BASE ASSY  
64 AGITATOR DRIVE GEAR  
65 AGITATOR  
66 PIN/STUD HOPPER  
67 GEAR AUGER DRIVE (HOPPER BASE), PLASTIC  
97098  
90268  
40692  
04026  
90210  
33 HEATER INDICATOR LIGHT AMBER  
34 WHIPPER MOTOR 115V  
35 WHIPPER MOTOR BRACKET PLATED  
C002C  
52038  
92177  
68 RETAINER PIN, STEEL (UNDER HOPPER)  
69 RETAINER PIN, S/STEEL (on coupling)  
70 SIDE PANEL  
04025  
04030  
RC40A  
10  
             
                      
                         
ꢁ  
DESCRIPTION AND LOCATION Oꢀ COMPONENTS  
ICAP1 B LD POUROVER (with lit door)  
%ꢀ %ꢁ $'  
$& $% $$  
$#  
%
$"  
$!  
$
!
"
$ꢀ  
$ꢁ  
#'  
#&  
#
$
#%  
#$  
%
&
##  
#"  
#!  
#
'
#ꢀ  
#ꢁ  
"'  
ꢀꢁ  
ꢀꢀ  
ꢀ!  
"&  
"%  
"#  
ꢀ"  
ꢀ#  
""  
"$  
"!  
"
"ꢀ  
ꢀ$  
ꢀ& ꢀ'  
%% ꢀ ꢀ  
& ' !!!!ꢀ ! !! !"  
! " # $ % & ' ! !! !" !!## !!$$ !!%% !!&& !!''""ꢁ  
" # $ %  
Illustration No. 9  
11  
ICAP1 B LD POUROVER (with lit door]  
ITEM DESCRIPTION  
P/N ITEM DESCRIPTION  
P/N  
1. COLD TANK COVER ASS'Y  
2. COLD WATER TANK WELDMENT ASS'Y  
Q164A  
Q163Q  
37. SLINGER DISC  
38. “O” RING  
83034  
?
3. WATER LEVEL FLOAT/CONTROL SWITCH (COLD)  
4. TANK TOP ASS'Y (FOR HOT WATER TANK)  
L499A  
Q166Q  
L467A  
97128  
20039  
39. MIXING CHAMBER MOUNT  
40. MIXER BLADE  
41. MIXING CHAMBER EXTENDER TUBE  
42. MIXING CHAMBER  
83033  
90230  
77184  
95001  
83036  
5.  
DISPENSE (DUMP) VALVE (MULLER)  
6. TANK BAFFLE ASS'Y  
7. TANK CLAMP SEAL  
43. MIXING CHAMBER INSERT  
8. TANK CLAMP ASS'Y  
9. HEATER ELEMENT 1750W 120V  
10. WASHER, HEATER ELEMENT  
97131  
G0140  
07059  
44. LAMP HOLDER MOUNTING BRACKET ( Lit Door )  
46. BREW SWITCH  
47. LAMP SOCKET - LEVITTON (for Lit Door only)  
RE52C  
L455A  
44496  
11. NUT, HEATER ELEMENT  
03051  
Q165Q  
59024  
09246  
48. FLUORESCENT LAMP 9W (for Lit Door only)  
49. DOOR WELDEMENT ASS'Y - ICAP1 B LD POUROVER RC53Q  
L042A  
12. HOT WATER TANK WELDMENT ASS'Y  
13. HI-LIMIT TEMPERATURE CONTROL  
14. ELBOW, MALE 1/8 NPT X 1/4  
50. TOP FRONT COVER  
51. AUGER MOTOR BRACKET  
RC42A  
73272  
15. CONTROL THERMOSTAT  
16. HOSE NUT  
17. WATER VALVE INLET ASS'Y  
59016  
95101  
L477A  
52. AUGER MOTOR 115V  
53. O RING  
54. GEAR, AUGER DRIVE MOTOR GEAR, PLASTIC  
52037  
20015  
90208  
18. HEATER SWITCH  
19. AUTO REFILL SWITCH  
20. POWER CORD  
21. LEGS, SET 2.5" BLK  
23. RELAY (DOUBLE POLE-on at all times) 120V  
24. TERMINAL BLOCK SINGLE  
25. BODY FRAME WELDMENT ASS'Y  
L299A  
L299A  
44242  
M034A  
L018A  
B135A  
RI88Q  
55. SUPPORT PLATE F/AUGER MOTOR  
56. CARTRIDGE HEATER 20W  
57. HEAT DUCT  
58. PRODUCT DISPENSER ADAPTER  
59. STEAM DEFLECTOR  
60. RESTRICTOR  
61. RESTRICTOR RETAINER  
90209  
87024  
97135  
CD70A  
90272  
92172  
34007  
26. POWER SWITCH (TOGGLE)  
27. POWER INDICATOR LIGHT, (red)  
28. GRILL  
L069A  
C165A  
75015  
62. PRODUCT ADJUSTER  
63. AUGER SPRING  
71001  
95116  
90211  
64. AUGER DRIVE COUPLING, PLASTIC  
29. DRIP TRAY PAN  
75060  
RE73A  
92007  
65. HOPPER & BASE ASS'Y  
66. AGITATOR DRIVE GEAR  
67. AGITATOR  
97098  
90268  
40692  
30. DRIPTRAY BRACKET (HOLDER)(OPTIONAL)  
31. STUD, DRIPTRAY  
68. PIN/STUD HOPPER  
69. GEAR AUGER DRIVE (HOPPER BASE), PLASTIC  
04026  
90210  
32. HEATER INDICATOR LIGHT AMBER  
C002A  
33. RINSE SWITCH  
34. INDICATOR LIGHT, GREEN "out of water/refill tank"  
35. WHIPPER MOTOR 115V  
56039  
C072A  
52038  
92177  
70. RETAINER PIN, STEEL (under Hopper)  
71. RETAINER PIN, S/STEEL (on Coupling)  
72. SIDE PANEL  
04025  
04030  
RC40A  
36. WHIPPER MOTOR BRACKET PLATED  
12  
DESCRIPTION AND LOCATION Oꢀ COMPONENTS  
ICAP MINI B LD (w/Lit Door) and MINI WHIPPER B (w/o Lit Door)  
!
$& $% $$ $#  
$"  
$!  
$
$ꢀ  
"
#
$ꢁ  
#'  
#&  
#%  
#$  
##  
$
%
&
'
ꢀꢁ  
#"  
#!  
#
ꢀꢀ  
ꢀ!  
#ꢀ  
#ꢁ  
ꢀ"  
ꢀ#  
"'  
"&  
"%  
"$  
ꢀ$  
ꢀ%  
ꢀ&  
ꢀ'  
"#  
""  
"!  
"
"ꢀ  
"ꢁ  
!'  
!&  
!%  
' !ꢁ !ꢀ ! !! !" !# !$  
! "  
%
&
# $  
Illustration No. 10  
13  
ICAP MINI 1 B LD w/lit door) & MINI WHIPPER B (w/o lit door)  
P/N ITEM DESCRIPTION  
ITEM DESCRIPTION  
P/N  
1
2
3
4
5
6
7
TANK TOP ASSY W/QC  
SILICONE TUBING (HOSE)  
HOSE CLAMP, METAL  
CHECK VALVE, PLASTIC  
TANK BAFFLE ASSY  
TANK BAFFLE SEAL  
97166  
77216  
34034  
M323A  
97170  
20039  
97131  
35 PLATE - MIX CHAMBER  
36 SEAL - MIX CHAMBER (GASKET)  
37 WING NUT  
38 HOSE BARB S/S 1/4 WITH FITTING  
39 MIXING CHAMBER  
40 EXTENDER-MIXING CHAMBER  
41 LAMP HOLDER MOUNTING BRACKET (for lit Door RE52A  
40138  
20032  
03005  
K436A  
97169  
83041  
TANK CLAMP ASSY  
8
9
HEATER ELEMENT 1500W/110V  
WASHER, HEATER ELEMENT  
87037  
07059  
03051  
97165  
59010  
42 BALLAST (for lit Door only) (CA33C older units  
43 PRODUCT SWITCH  
44 LAMP SOCKET - LEVITTON (for lit Door only)  
45 FLOURESCENT LAMP 9W (for lit Door only)  
46 DOOR WELDMENT ASSY - ICAP 1 B LD  
CE221  
L455A  
44496  
L042A  
RC53Q  
10 NUT, HEATER ELEMENT  
11 TANK  
12 HI-LIMIT TEMPERATURE CONTROL  
13 DRAIN PLUG, BRASS  
14 CONTROL THERMOSTAT  
15 TOP FRONT COVER  
16 HOSE BARB FITTING  
K044A  
59016  
RC42A  
K435A  
47 AUGER MOTOR BRACKET  
48 AUGER MOTOR 115V  
49 SUPPORT PLATE F/AUGER MOTOR  
50 GEAR, AUGER DRIVE MOTOR GEAR, PLASTIC  
73272  
52037  
90209  
90208  
17 ADJ. VALVE ASSY #H5107 NPT  
18 HOSE NUT  
19 WATER VALVE INLET ASSY  
20 POWER CORD  
K415A  
95101  
L477A  
44242  
58017  
51 O RING  
52 CARTRIDGE HEATER  
53 HEAT DUCT  
54 PRODUCT GUIDE (SHUTE)  
55 STEAM DEFLECTOR  
20015  
87024  
97167  
CD70A  
90272  
21 TIMER (for automatic units only) 120v  
22 TERMINAL BLOCK SINGLE  
23 BODY FRAME WELDMENT ASSY  
24 LEGS (2.5") BLACK, PLASTIC (OPTIONAL)  
RUBBER FEET 1" BLACK (W/O BRACKETS  
25 STUD-DRIP TRAY  
B135A  
RG94Q  
M034A  
18003  
92007  
75060  
56 RESTRICTOR  
57 RETAINER  
58 PRODUCT ADJUSTER  
92173  
34007  
71001  
59 AUGER SPRING  
60 AUGER DRIVE COUPLING, PLASTIC  
95116  
90211  
26 DRIP TRAY PAN  
27 GRILL  
75015  
61 HOPPER & BASE ASSY  
62 GEAR, AGITATOR DRIVE  
63 AGITATOR  
64 PIN (STUD) HOPPER  
65 GEAR AUGER DRIVE (HOPPER VBASE), PLASTIC 90210  
97098  
90268  
40692  
04026  
28 BRACKET-DRIP TRAY HOLDER (OPTIONAL W/2.5" LEGS ONLY) RE73A  
29 RINSE SWITCH  
30 HEATER SWITCH  
31 HEATER INDICATOR LIGHT AMBER  
56039  
L299A  
C002A  
32 NUT - FOR SPACER  
33 WASHER - FOR SPACER  
34 SPACER - MIX CHAMBER (STUD)  
03003  
07007  
05041  
66 RETAINER PIN, STEEL, (UNDER HOPPER)  
67 RETAINER PIN, S/STEEL, (ON COUPLING)  
68 SIDE PANEL  
04025  
04030  
RC75A  
14  
AUTOMATIC:ꢀꢀICAP 1 B LD [LIT DOOR]  
&
WHIPPER B [NO LIT DOOR]  
AUTOMATIC: ICAP 1 MINI B LD [LIT DOOR]  
&
MINI WHIPPER B [NO LIT DOOR]  
15  
MANUAL - ICAP 1 B LD [LIT DOOR]  
MANUAL - ICAP 1 MINI B LD [LIT DOOR]  
16  
DOOR UNIT  
INDICATOR LIGHT  
"OUT Oꢀ WATER"  
"REILL TANK"  
NOTE: TO CONVERT TO TIMER CONTROLLED DISPENSE,  
CONNECT "BLUE" WIRE TO TIMER TERMINAL "L1".  
CONNECT "YELLOW" WIRES TO TIMER TERMINAL "NO".  
CONNECT "ORANGE" WIRES TO TIMER TERMINAL "N".  
USE PIGGY BACK TERMINAL PROVIDED.  
17  
18  

Nokia 5125 User Manual
Nespresso C100 User Manual
Motorola MOTORAZR V9m User Manual
Lindy KVM EXTENDER 32359 User Manual
IBM C4B 451 Brick On Sled carrier 128 pin HPC User Manual
GE PDW8800 User Manual
Fujitsu MHZ2160BJ User Manual
Emerson CLD Analyzer Module NGA2000 User Manual
Creative Zen Vision Cell Phone User Manual
Cisco Systems Computer Accessories User Manual