Casio DQD 106 User Manual

MA0702-EA  
Operation Guide DQD-106  
A sticker is affixed to the glass of this clock when you purchase it. Be sure to remove the sticker before using the  
ILLUSTRATION  
clock.  
Depending on its model number, the appearance of your clock may differ somewhat from that shown in the  
illustration.  
4 5  
Alarm Off  
Antenna Icon  
Snooze Alarm On  
Current time  
(Hour, minutes, seconds)  
Snooze on indicator  
DST indicator  
PM indicator  
2
Alarm on indicator  
Day of the week  
Wave OK indicator  
Date (month – date)  
Current Temperature  
3 6  
7
GENERAL GUIDE  
1SNOOZE/LIGHT button  
Press this button to illuminate the display for about four seconds.  
Pressing this button while the alarm is sounding stops the alarm.  
2Alarm Mode selector  
SNZ: Snooze alarm on  
ALM ON: Alarm on  
1
ALM OFF: Alarm off  
3Alarm Time Set buttons  
Use these buttons to change the alarm time or current time setting.  
4SET button  
Use this button when setting the current time.  
5WAVE button  
Press this button to receive the time calibration signal and adjust timekeeping.  
1
6°C/°F button  
Press this button to toggle the temperature units between Celsius and Fahrenheit.  
2
7RESET button  
Press this button to reset the clock after replacing its batteries.  
8Batteries  
8
1
Operation Guide DQD-106  
USING THE ALARM  
THERMOMETER FUNCTIONS  
The alarm sounds and the light turns on when the alarm time you set is reached. You can also use the Alarm  
Mode selector (2) to select the snooze alarm feature.  
A built-in sensor measures temperature and shows the measured value on the display. The readout from the  
temperature sensor can also be switched between Celsius (°C) and Fahrenheit (°F).  
Setting the Alarm Time  
Temperature Measurements  
Use the Alarm Time Set buttons (3) to set the alarm time.  
Pressing the Alarm Time Set buttons (3) causes the alarm time to appear in place of the time on the display.  
The temperature display shows “LO” for temperatures below –50°C (–58°F) and “HI” for temperatures above  
70°C (158°F).  
Though temperature readings are displayed up to 0°C (32°F) and greater than 41°C (105°F), note that such  
readings are actually outside the guaranteed temperature range of this clock.  
Press to change the  
alarm time setting (+).  
Press to change the  
alarm time setting (  
Switching between Celsius and Fahrenheit  
Push the °C/°F button (6) to select either Celsius (°C) or Fahrenheit (°F).  
).  
Celsius (°C)  
Fahrenheit (°F)  
°C/°F button (6)  
Holding down + or changes the digits at high speed.  
Turning the Alarm On and Off  
Use the Alarm Mode selector (2) on the side of the clock to turn the alarm on and off, and to select the snooze  
feature.  
°C/°F button (6)  
Alarm Mode selector  
SNZ  
Description  
°C  
°F  
The alarm sounds at the preset time for one minute, and seven  
more times every five minutes thereafter. Even if you stop the  
alarm sound by pressing the SNOOZE/LIGHT button (1), the  
alarm operation is performed again five minutes later.  
flashes on the display to indicate that the  
snooze feature is activated.  
BATTERY REPLACEMENT  
Replace batteries whenever the display of the clock becomes dim and difficult to read.  
1. Open the battery compartment cover as shown in the illustration.  
2. Remove all of the old batteries.  
( )  
The indicator  
3. Load a full set of new batteries. Make sure that their positive (+) and negative (–) ends face in the correct  
directions. If you load batteries incorrectly, they can burst and damage the clock.  
4. Replace the battery compartment cover.  
ALM ON  
The alarm sounds at the preset time for one minute.  
5. Press the RESET button (7). Be sure to press the RESET button (7) after replacing batteries.  
( )  
ALM OFF  
Battery precautions  
Keep batteries out of the reach of small children. If a battery is swallowed accidentally, contact your physician  
The alarm does not sound.  
immediately.  
Be sure to load the batteries with their positive (+) and negative (–) ends facing correctly.  
Never mix old and new batteries, or batteries of different brands.  
Never charge the batteries that come with the clock.  
The light also turns on for the first five seconds that the alarm sounds.  
The alarm sound changes over four levels as it sounds.  
Stopping the Alarm  
Should batteries ever leak while in the clock, wipe out the fluid with a cloth, taking care not to let any get onto  
your skin.  
When alarm is sounding, press the SNOOZE/LIGHT button (1) to stop it. When the snooze feature is turned  
Replace the batteries at least once a year, even if the current batteries are working properly.  
The batteries that come with the clock lose some of their power during transport and storage.  
on, the alarm will sound again in about five minutes.  
To turn off the snooze feature, slide the Alarm Mode selector (2) to ALM OFF.  
USING THE LIGHT  
Pressing the SNOOZE/LIGHT button (1) turns on the light and illuminates the display for easy reading in the  
dark.  
Important!  
Overuse of the light can shorten battery life.  
3

Nespresso D100 User Manual
Motorola MOTO Z9n User Manual
Motorola i760 User Manual
JVC KS FX772R User Manual
Hitachi Computer Drive 4K40 User Manual
Fluke IMPULSE 6000D User Manual
Emotiva ERC 1 User Manual
Casio Keyboard WK 500 User Manual
Asus CARTE MERE A7N8X E User Manual
Addonics Technologies PPROESP User Manual