2322/2323-1
Module No.2322/2323
GENERAL GUIDE
• Press A to change from mode to mode.
The operational procedures for Module 2322 and 2323 are identical. All of the
illustrations in this manual show Module 2322.
Timekeeping Mode
Calendar Mode
Alarm Mode
Dual Time Mode
Stopwatch Mode
[Module 2323]
[Module 2322]
ABOUT THE BACKLIGHT
ALARM MODE
• Press L to illuminate the display for about 2 seconds.
When the Daily Alarm is turned on, an alarm sounds for 20 seconds at the preset time each
day. When the Hourly Time Signal is switched on, the watch beeps every hour on the hour.
• The backlight of this watch employs an electro-luminescent (EL) light, which loses its illumi-
nating power after very long term use.
• Frequent use of the backlight shortens the battery life.
• The watch emits an audible sound whenever the display is illuminated. This does not indicate
malfunction of the watch.
• The illumination provided by the backlight may be hard to see when viewed under direct
sunlight.
To set the alarm time and to turn the Daily Alarm and Hourly Time Signal on and of
f
Alarm on indicator
Hourly Time Signal on indicator
• The backlight automatically turns off whenever an alarm sounds.
• When the backlight is turned on, it blinks whenever the minute hand moves. This is normal,
and does not indicate malfunction of the watch.
Hold down
C.
Press
C.
Press
C.
Left
minutes
digit
Right
minutes
digit
Hour
Press C.
Press C.
Alarm/Hourly Time Signal on/off setting
Alarm/Hourly Time Signal seting
TIMEKEEPING MODE
Hour Minutes
• Use this mode to set the current time. An incorrect digital time setting will result in incorrect
1. Hold down C until the hour digits start to flash.
operation of the calendar.
2. Press A to increase the hour digits. Holding down A changes the digits at high speed.
• The format (12-hour and 24-hour) of the alarm time matches the format you select for normal
timekeeping.
3. Press C to move the selection to the left minutes digit.
4. Press A to increase the left minutes digit. Holding down A changes the digit at high speed.
5. Press C to move the selection to the right minutes digit.
To set the time and date
Hour hand Minute hand
6. Press A to increase the right minutes digit. Holding down A changes the digit at high speed.
7. Press C to move Daily Alarm and Hourly Time Signal on and off setting.
8. Press A to change the status of the Daily Alarm and Hourly Time Signal in the following
sequence.
Hold down C.
Press C.
Hour
Press C.
Seconds
• At this time Daily Alarm and Hourly Time Signal automatically turn on.
12/24
Minutes
Press C.
Press C.
Hour Seconds
Minutes
PM indicator
Both ON
Both ON
Both OFF
Both OFF
Daily Alarm
Hourly Time
Signal only
Daily Alarm
Hourly Time
only
1. Hold down C until the seconds digits start to flash.
2. Press A to reset the seconds to 00. If you press A while the seconds count is in the range
of 30 to 59, the seconds are reset to 00 and 1 is added to the minutes. If the seconds count
is in the range of 00 to 29, the minutes count is unchanged.
9. Press C to complete the procedure.
• If you do not operate any button for a few minutes while a selection is flashing, the flashing
stops and the watch goes back to the Alarm Mode automatically.
3. Press C to move the selection to the hour digits.
4. Press A to increase the hour digits. Holding down A changes the hour digits at high speed.
5. Press C to move the selection to the minutes digits.
6. Press A to increase the minutes digits. Holding down A changes the minutes digits at high
speed.
To stop the alarm
• Press any button to stop the alarm after it starts to sound.
To test the alarm and select an alarm tone
7. Press C to move the selection to 12/24.
Hold down A in any mode (except when making any settings) to sound the alarm.
Each time you test the alarm, a four different alarm tones. The alarm tone you select is used for
the Daily Alarm and Hourly Time Signal.
• Note that holding down A also changes the mode.
8. Press A to toggle the timekeeping format between 12-hour and 24-hour.
• When 12-hour format is selected, the indicator P appears on the display to indicate “p.m.”
times. There is no indicator for “a.m.” times.
9. Press C to complete the procedure.
• If you do not operate any button for a few minutes while a selection is flashing, the flashing
stops and the watch goes back to the Timekeeping Mode automatically.
To set the hands
DUAL TIME MODE
To semt the Dual Time
When in any Mode, press B with a thin object to advance the analog time setting. Each press
of B advances the time by 20 seconds. Three presses advance by one minute.
Holding down B advances the analog setting at high speed. You can only advance the setting
and cannot reverse it.
Hold down C.
Press C.
Minutes
Press C.
12/24
CALENDAR MODE
To set the date
Hour
Press C.
Hour
Minutes
PM indicator
Seconds
Hold down C.
Press C.
Day
Press C.
Day of week
1. Hold down C until the hour digits start to flash.
2. Press A to increase the hour digits. Holding down A changes the digits at high speed.
3. Press C to move the selection to the minutes digits.
Month
4. Press A to increase the minutes digits. Holding down A changes the digits at high speed.
5. Press C to move the selection to 12/24.
6. Press A to toggle the timekeeping format between 12-hour and 24-hour.
• When 12-hour format is selected, the indicator P appears on the display to indicate “p.m.”
times. There is no indicator for “a.m.” times.
Press C.
Month
Day of week
Day
1. Hold down C until the month digits start to flash.
7. Press C to complete the procedure.
2. Press A to increase the month digits. Holding down A changes the digits at high speed.
3. Press C to move the selection to day digits.
4. Press A to increase the day digits. Holding down A changes the digits at high speed.
5. Press C to move the selection to the day of the week indication.
6. Press A to advance to the next day. Holding down A changes the indication at high speed.
7. Press C to complete the procedure.
• If you do not operate any button for a few minutes while a selection is flashing, the flashing
stops and the watch goes back to the Dual Time Mode automatically.
• In the Dual Time Mode, the seconds count is synchronized with the seconds count of the
Timekeeping Mode.
• If you do not operate any button for a few minutes while a selection is flashing, the flashing
stops and the watch goes back to the Calendar Mode automatically.
|