Black Box Computer Accessories ACU5250A R2 User Manual

®
®
ACU5050A-R2  
ACU5250A-R2  
NETWORK SERVICES  
ServSwitch Wizard VGA/USB™  
Extend one or two* VGA video links plus four USB  
devices and speakers up to nearly 1000 feet from  
your computer.  
Uses one or two* length of Category 5, 5e, 6, 7 or 7a twisted-pair cable.  
* Dual-variant models  
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)  
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746  
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018  
Customer  
Support  
Information  
FCC and IC RFI Statements  
Federal Communications Commission and Industry Canada Radio Frequency Interference  
Statements  
This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict  
accordance with the manufacturer’s instructions, may cause interference to radio communication. It has been tested and found to  
comply with the limits for a Class A computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules,  
which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial  
environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his own  
expense will be required to take whatever measures may be necessary to correct the interference.  
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to  
operate the equipment.  
This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out in the Radio  
Interference Regulation of Industry Canada.  
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de  
la classe A prescrites dans le Règlement sur le brouillage radioélectrique publié par Industrie Canada.  
724-746-5500 | blackbox.com  
Page 3  
ServSwitch Wizard VGA/USB  
Instrucciones de Seguridad  
(Normas Oficiales Mexicanas Electrical Safety Statement)  
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado.  
2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.  
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación deben ser respetadas.  
4. Todas las instrucciones de operación y uso deben ser seguidas.  
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la tina de baño, lavabo, sótano mojado o cerca  
de una alberca, etc.  
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean recomendados por el fabricante.  
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea recomendado por el fabricante.  
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo descrito en las instrucciones de operación.  
Todo otro servicio deberá ser referido a personal de servicio calificado.  
9. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su uso. La colocación del aparato eléctrico  
sobre una cama, sofá, alfombra o superficie similar puede bloquea la ventilación, no se debe colocar en libreros o gabinetes  
que impidan el flujo de aire por los orificios de ventilación.  
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como radiadores, registros de calor, estufas u otros  
aparatos (incluyendo amplificadores) que producen calor.  
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo descrito en el instructivo de operación, o como  
se indique en el aparato.  
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada.  
13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados  
sobre o contra ellos, poniendo particular atención a los contactos y receptáculos donde salen del aparato.  
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomendaciones del fabricante.  
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas de energia.  
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo.  
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilación.  
18. Servicio por personal calificado deberá ser provisto cuando:  
A: El cable de poder o el contacto ha sido dañado; u  
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o  
C: El aparato ha sido expuesto a la lluvia; o  
D: El aparato parece no operar normalmente o muestra un cambio en su desempeño; o  
E: El aparato ha sido tirado o su cubierta ha sido dañada.  
724-746-5500 | blackbox.com  
Page 4  
Table of Contents  
Contents  
1. Specifications.............................................................................................................................................................................. 6  
2. Overview.................................................................................................................................................................................... 7  
3. Installation.................................................................................................................................................................................. 8  
3.1 Mounting the modules – desk or rack............................................................................................................................... 8  
3.1.1 Desk mount .......................................................................................................................................................... 8  
3.1.2 Rack mount.......................................................................................................................................................... 9  
3.2 Connections ................................................................................................................................................................... 10  
3.2.1 Connections at the local module........................................................................................................................ 10  
3.2.2 Connections at the remote module ................................................................................................................... 16  
3.2.3 Dual user configuration...................................................................................................................................... 20  
3.3 Video display (DDC) information..................................................................................................................................... 22  
3.3.1 DDC indications ................................................................................................................................................. 23  
3.4 Video compensation....................................................................................................................................................... 24  
3.4.1 To enter video compensation mode................................................................................................................... 25  
3.4.2 To exit video compensation mode (return to normal operation) ........................................................................ 25  
3.4.3 To set the cable type.......................................................................................................................................... 26  
3.4.4 To set the cable length....................................................................................................................................... 26  
3.4.5 To adjust video gain........................................................................................................................................... 27  
3.4.6 To adjust color skew........................................................................................................................................... 27  
4. Operation................................................................................................................................................................................. 28  
4.1 General use..................................................................................................................................................................... 28  
4.2 Dual user arbitration....................................................................................................................................................... 28  
4.3 Peripheral operation ....................................................................................................................................................... 28  
4.3.1 USB.................................................................................................................................................................... 28  
Appendix A. Troubleshooting....................................................................................................................................................... 30  
A.1 Status indicators ............................................................................................................................................................. 30  
Appendix B. Safety Information.................................................................................................................................................... 31  
724-746-5500 | blackbox.com  
Page 5  
ServSwitch Wizard VGA/USB  
1. Specifications  
ServSwitch Wizard VGA/USB single-variant  
Casings (w x h x d):  
118.4mm (4.66”) x 26mm (1.02”) x 74.8mm (2.94”)  
Construction:  
1U compact case, robust metal design  
0.33kg (0.72lbs)  
Weight:  
Mount kits:  
Rack mount  
Power to adapter:  
Power to remote unit:  
Operating temp:  
Approvals:  
100-240VAC 50/60Hz, 0.5A,  
5VDC 12.5W  
32 to 104°F (0 to 40°C)  
CE, FCC  
ServSwitch Wizard VGA/USB dual-variant  
Casings (w x h x d):  
Local module: 122mm (4.7’’) x 48mm (2’’) x 75mm (3’’)  
Remote module: 162mm (6.4’’) x 48mm (2’’) x 75mm (3’’)  
Construction:  
Weight:  
1U compact case, robust metal design  
Local module: 500g (1.1lbs)  
Remote module: 650g (1.4lbs)  
Mount kits:  
Rack mount  
Power to adapter:  
Power to units:  
Operating temp:  
Approvals:  
100-240VAC 50/60Hz, 0.5A,  
5VDC 12.5W  
0ºC to 40ºC (32ºF to 104ºF)  
CE, FCC  
724-746-5500 | blackbox.com  
Page 6  
Chapter 2: Overview  
2. Overview  
Thank you for choosing the ServSwitch Wizard VGA-USB extenders which provide a very effective way to put distance  
between your computer and its peripherals.  
The compact casings and ease of use of the modules belie the ingenuity of their operation. Using our proprietary transmission  
techniques we are able to reliably transfer more signals than ever before along a single length of Category 5, 5e, 6, 7 or 7a twist-  
ed pair cabling. What this means for you is that your video, audio, USB keyboard, USB mouse and two other USB channels are all  
readily and reliably available at up to 984 feet (300 meters) away.  
Using the ServSwitch Wizard VGA-USB extenders does not mean that you need to compromise on functionality in any way. Our  
highly efficient transmission methods mean that CD quality sound and high video resolutions of up to 1920 x 1200 are fully sup-  
ported. Any lag effects caused by long cable runs are easily eliminated using the intuitive video compensation system located  
within the remote module. Three equalisation bands allow you to ensure that every color arrives at precisely the right time, ensur-  
ing a sharp image every time. The ServSwitch Wizard VGA-USB dual-variant models use an additional CATx connection to provide  
dual analog video links.  
The USB connections are seamless allowing four full speed USB 2.0 devices to be used simultaneously with full support for discon-  
nect/re-connect at any time without causing errors.  
The ServSwitch Wizard VGA-USB extenders have been designed to be quick to install and totally transparent in operation: ‘Fit and  
forget’ is the motto. So whether you are extending your workplace or creating a cost-effective distributed audio visual system, the  
ServSwitch Wizard VGA-USB extenders provide the power and flexibility to create the right solution.  
PC  
OUT  
CATx link cable  
POWER  
POWER  
OUT  
IN  
REMOTE  
LOCAL  
CATx link cable (2)  
VIDEO (2)  
VIDEO  
AUDIO  
USB  
OUT  
Up to 984 feet  
(300 meters)  
separation  
LINK  
TO REMOTE  
ON  
LINK  
TO LOCAL  
ON  
IN  
S e r v S w i t c hW i z a r d V G A / U S B  
S e r v S w i t c hW i z a r d V G A / U S B  
L
B
L
A
C
K
B
O
X
K
V
M
E
X
T
E
N
D
E
R
B
A
C
K
B
O
X
K
V
M
E
X
T
E
N
D
E
R
USB  
device  
USB  
device  
Maximum cable lengths  
CAT 5  
820 feet (250 m)  
CAT 5e  
CAT 6  
820 feet (250 m)  
984 feet (300 m)  
984 feet (300 m)  
656 feet (200 m)  
The dual-variant  
provides a second  
analog video channel.  
*
CAT 7  
CAT 7a Patch  
724-746-5500 | blackbox.com  
Page 7  
ServSwitch Wizard VGA/USB  
3. Installation  
3.1 Mounting the modules – desk or rack  
The modules can be situated on a desk or alternatively, for larger installations, mounted within an optional rack mount chassis.  
3.1.1 Desk mount  
Apply the supplied self-adhesive rubber feet to the underside of the module as shown in Figure 3-1:  
Figure 3-1. Applying the supplied self-adhesive rubber feet to the underside of the module  
724-746-5500 | blackbox.com  
Page 8  
Chapter 3: Installation  
3.1.2 Rack mount  
Note: The module switches are not accessible once it is inserted into the rack, therefore, check all settings before insertion.  
1 Place the rack securing plate (available as a separate kit) onto the front of the module and secure it with the two countersunk  
screws.  
2 Orient the module on its side so that its labeled face is the correct way up.  
3 Slide the module into the required rack position. The rectangular cut-out in the front upper lip of the rack allows the two  
screws on the module’s upper edge to slide through.  
4 The rack mount chassis has a series of holes in its floor that are spaced to accommodate the two screws on the module’s lower  
edge. Ensure that the screws correctly locate into the two holes of the chosen slot. The rack securing plate on the module  
should now be flush with the front of the rack mount chassis.  
5 Use the third (pan-head) screw, in the top hole of the rack securing plate to fasten the module to the rack as shown in Figure  
3-2:  
I
N
ON  
2
3
4
L
O
L
I
N
P
O
W
E
R
O
U
T
S
B
e
L
r
A
v
S
w
C
i
t
B
K
c
O
W
X
i
z
V
a
M
K
r
d
L
I
V
X
N
K
T
G
T
E
O
A
E
R
E
/
N
M
O
U
D
T
E
S
E
B
O
R
N
Figure 3-2. Fixing the module into the rack  
724-746-5500 | blackbox.com  
Page 9  
ServSwitch Wizard VGA/USB  
3.2 Connections  
Installation of the modules is straightforward and requires minimal configuration in most cases.  
• Connections at the local module  
• Connections at the remote module  
IMPORTANT: The ServSwitch Wizard VGA-USB can be used with other hubs in the system, but please note that the local unit  
should not be connected to the downstream port of a bus-powered hub due to power constraints. Additionally, dual-variant local  
units must always be powered using their supplied power adapter. Please see section 3.2.1.5 Local module power for details.  
3.2.1 Connections at the local module  
3.2.1.1 Video connections  
1 Where possible ensure that power is disconnected from the computer system to be connected.  
2 Use the supplied VGA link cable to connect the VGA input socket of the local module to the video output socket of the com-  
puter as shown in Figure 3-3:  
O
T
U
N
I
e
S
N
I
Figure 3-3. Attaching the VGA video link cable  
[Dual-variant only] Optionally attach a second  
T
U
O
video input from the computer system.  
N
I
e
S
N
I
B
N
I
A
To secondary video  
output port  
To primary video  
output port  
Figure 3-4. Attaching two VGA video link cables to the dual-variant local module  
724-746-5500 | blackbox.com  
Page 10  
Chapter 3: Installation  
3 Optionally connect a local video display to the video out feed-through connector on the local module as shown in Figure 3-5:  
U
E
S
R
B
T
O
O
R
E
N
M
O
T
E
L
I
N
K
O
U
T
P
O
W
E
R
Figure 3-5. Optionally attaching a video display to the local module  
h
W ™  
K
V
i
M
z
a
r
E
d
X
[Dual-variant only] Optionally connect a second local  
video display to the upper socket on the local module.  
T
V
E
G
N
A
D
/
U
E
S
R
B
T
O
O
R
E
N
M
O
T
E
L
I
N
K
B
O
U
T
A
O
U
T
P
O
W
E
R
Figure 3-6. Attaching two VGA video displays to the dual-variant local module  
724-746-5500 | blackbox.com  
Page 11  
ServSwitch Wizard VGA/USB  
3.2.1.2 USB connections  
IMPORTANT: The Wizard VGA/USB can be used with other USB hubs in the system, but please note that due to power con-  
straints, the local unit should not be connected to the downstream port of a bus-powered USB hub. Additionally, Wizard VGA/  
USB dual-variant local units must always be powered using their supplied power adapter. Please see section 3.2.1.5 Local module  
power for details.  
1 Use the supplied USB cable to link the USB socket of the local module to a vacant USB socket on the computer as shown in  
Figure 3-7:  
L
A
C
O
L
T
U
O
N
I
e
S
N
I
B
T
U
N
O
I
A
N
I
e
S
N
I
Figure 3-7. Attaching the USB link cable to the single- and dual-variant local modules  
724-746-5500 | blackbox.com  
Page 12  
Chapter 3: Installation  
3.2.1.3Audio connections  
1 Optionally connect an audio link from the computer’s speaker port to the audio input port on the local module as shown  
in Figure 3-8.  
L
A
C
O
L
T
U
O
N
I
e
S
N
I
B
T
N
I
U
A
O
N
I
e
S
N
I
Figure 3-8. Attaching an audio input to the single- and dual-variant local modules  
2 Optionally connect local speakers to the audio output port on the local module as shown in Figure 3-9.  
L
A
C
O
L
T
U
O
N
I
N
I
B
T
U
N
O
I
A
N
I
N
I
Figure 3-9. Attaching speakers to the single- and dual-variant local modules  
724-746-5500 | blackbox.com  
Page 13  
ServSwitch Wizard VGA/USB  
3.2.1.4 Link connections  
1 Connect the link cable (up to 984 feet/300 meters in length) to the local module socket labeled TO REMOTE as shown in Figure  
3-10:  
U
E
S
R
B
T
O
O
R
E
N
M
O
T
E
L
I
N
K
O
U
T
P
O
W
E
R
Figure 3-10. Attaching the CATx link cable  
W ™  
K
V
[Dual-variant only] Attach a second category 5e, 6 or 7a  
link cable (up to 984 feet/300 meters in length) to the  
upper socket on the dual-variant local module.  
i
M
z
a
r
E
d
X
T
V
E
G
N
A
D
/
U
E
S
R
B
T
O
O
R
E
N
M
O
T
E
L
I
N
K
B
O
U
T
A
O
U
T
P
O
W
E
R
Secondary CATx  
link cable  
Primary CATx  
link cable  
Figure 3-11. Attaching two CATx link cables to a dual-variant local module  
Ensure that the primary and secondary links from the local module are not crossed.  
724-746-5500 | blackbox.com  
Page 14  
Chapter 3: Installation  
3.2.1.5 Local module power  
The single- and dual-variant local modules differ in the way that they are powered:  
• The single-variant local module is designed to derive its power from the host computer via the USB connection. If this is not  
possible, then use an optional power adapter, available from your Black Box stockist.  
• The dual-variant local module always requires the use of a power adapter and hence two power adapters are supplied with all  
Wizard VGA/USB dual-variant units.  
For all dual-variant and optionally for single-variant units:  
1 Connect the output lead of the optional power adapter to the socket labelled ‘POWER‘ on the local module. See Figure 3-12.  
T
X
O
T
V
O
R
E
N
E
G
M
O
N
A
T
E
D
/
L
I
N
U
E
K
S
R
B
T
O
O
R
E
N
M
O
O
T
U
E
T
L
I
N
P
K
O
W
E
R
B
O
U
T
A
O
U
T
P
O
W
E
R
Figure 3-12. The use of a power supply on single-variant  
local modules is optional. Dual-variant local modules  
always require a power supply.  
2 Insert the IEC connector of the separate power lead into the corresponding socket of the power adapter. See Figure 3-13.  
Figure 3-13. Inserting the IEC connector of the power lead  
3 When all other connections have been made at the transmitter and receiver modules, connect the other end of the power  
cable to a nearby earthed power outlet.  
4 After all connections are made, power up the monitor and the REMOTE module first (followed by the LOCAL module, if  
using the dual-variant) and then switch on the computer.  
724-746-5500 | blackbox.com  
Page 15  
ServSwitch Wizard VGA/USB  
3.2.2 Connections at the remote module  
3.2.2.1 Video connections  
1 Where possible ensure that power is disconnected from the computer system to be connected.  
2 Attach the lead from the video display to the video out socket on the remote module as shown in Figure 3-14:  
Figure 3-14. Attaching the VGA video display cable  
[Dual-variant only] Optionally attach the lead from a second video display to the upper video out socket on the dual-vari-  
ant remote module.  
E
T
O
M
E
R
B
A
To secondary  
video display  
To primary  
video display  
Figure 3-15. Attaching two VGA video display cables to the dual-variant local module  
724-746-5500 | blackbox.com  
Page 16  
Chapter 3: Installation  
3.2.2.2 USB connections  
1 Attach the leads of up to four USB devices (two of which are usually a keyboard and mouse) to the sockets located adjacent to  
the video output connector as shown in Figure 3-16:  
T
O
M
E
R
B
A
Figure 3-16. Attaching the keyboard, mouse and other USB cables  
[Dual-variant only] IMPORTANT: When connecting four USB devices to the remote module, ensure that their total power  
requirements do not exceed 1700mA (1.7A). The USB standard states a maximum allowable current draw of 500mA (0.5A)  
per device, although most devices remain well below this limit - USB keyboards and mice typically require 100mA. Each  
Wizard VGA-USB module contains a self-resetting fuse that will prevent damage by shutting down the unit if the total power  
draw becomes excessive.  
3.2.2.3 Audio connections  
1 Optionally attach the lead from your stereo speakers to the audio output socket on the remote module as shown in  
N
A
D
/
Figure 3-17:  
U
E
S
R
B
T
O
O
L
N
O
C
A
L
L
I
N
B
K
O
U
T
T
O
O
L
N
O
C
A
L
L
I
N
K
P
O
W
E
R
O
U
T
P
O
W
E
R
Figure 3-17. Optionally attaching stereo speakers  
724-746-5500 | blackbox.com  
Page 17  
ServSwitch Wizard VGA/USB  
3.2.2.4 Link connections  
1 Attach the connector of the category 5, 5e, 6, 7 or 7a link cable (up to 984 feet/300 meters in length) to the ‘TO LOCAL’  
socket on the remote module as shown in Figure 3-18:  
T
O
O
L
N
O
C
A
L
L
I
N
K
O
U
T
P
O
W
E
R
Figure 3-18. Attaching the CATx link cable  
[Dual-variant only] Connect a second category 5, 5e, 6, 7 or 7a link cable (up to 984 meters in length) to the upper socket on  
the remote module as shown in Figure 3-19:  
V
i
M
z
a
r
E
d
X
T
V
E
G
N
A
D
/
U
E
S
R
B
T
O
O
L
N
O
C
A
L
L
I
N
K
O
U
T
P
O
W
E
R
Secondary CATx  
link cable  
Primary CATx  
link cable  
Figure 3-19. Attaching two CATx link cables to a dual-variant remote module.  
Ensure that the primary and secondary links from the local module are not crossed.  
724-746-5500 | blackbox.com  
Page 18  
Chapter 3: Installation  
3.2.2.5 Remote module power  
1 Attach the output connector of the power adapter to the ‘POWER’ socket of the remote module as shown in Figure 3-20:  
T
O
O
L
N
O
C
A
L
L
I
N
K
B
O
U
T
T
O
O
L
N
O
C
A
L
P
L
O
I
N
W
K
E
R
O
U
T
P
O
W
E
R
Figure 3-20. Attaching the power adapter  
2 Attach the IEC power cord to the power adapter body and insert the mains plug of the cord to a nearby power outlet as  
shown in Figure 3-21:  
Figure 3-21. Attaching the power cord to the adapter  
724-746-5500 | blackbox.com  
Page 19  
ServSwitch Wizard VGA/USB  
3.2.3 Dual user configuration  
You can combine two ServSwitch Wizard VGA-USB extender sets to create a dual user configuration. Such an installation would  
allow a single computer to be controlled from two different positions, with each position receiving the same audio visual output  
and having equal and concurrent control over the computer. Arbitration between the two positions is handled by the computer’s  
USB system and so this arrangement is better suited to situations where two users would not often require simultaneous access.  
USER  
POWER  
REMOTE  
1
OUT  
LINK  
TO LOCAL  
ON  
S e r v S w i t c hW i z a r d V G A / U S B  
R
B
L
A
C
K
B
O
X
K
V
M
E
X
T
E
N
D
E
PC  
CATx link (up to 984 feet)  
OUT  
IN  
POWER  
OUT  
LOCAL  
VIDEO  
AUDIO  
LINK  
IN  
USB  
TO REMOTE  
ON  
S e r v S w i t c hW i z a r d V G A / U S B  
R
B
L
A
C
K
B
O
X
K
V
M
E
X
T
E
N
D
E
Video and audio crosslinks are  
made from first local module to  
the second local module  
OUT  
IN  
POWER  
OUT  
LOCAL  
LINK  
IN  
TO REMOTE  
ON  
S e r v S w i t c hW i z a r d V G A / U S B  
E
B
L
A
C
K
B
O
X
K
V
M
E
X
T
E
N
D
R
CATx link (up to 984 feet)  
Both local modules  
require their own  
USB links to the PC  
USER  
2
POWER  
REMOTE  
OUT  
LINK  
TO LOCAL  
ON  
S e r v S w i t c hW i z a r d V G A / U S B  
E
B
L
A
C
K
B
O
X
K
V
M
E
X
T
E
N
D
R
Figure 3-22. The logical layout of a dual user configuration  
724-746-5500 | blackbox.com  
Page 20  
Chapter 3: Installation  
R
E
W
O
P
T
U
O
First local module  
K
N
I
L
E
T
O
M
E
R
N
O
T
U
O
T
O
B
L
N
I
A
S
U
/
A
G
V
e
S
d
r
a
z
N
i
I
W
h
c
t
i
w
S
v
r
e
S
Video crosslink  
from first to  
second local  
module  
Audio, USB and  
video from the PC  
T
U
O
N
I
e
Audio crosslink  
S
N
I
from first to  
second local  
module  
Second USB  
from the PC  
Figure 3-23. Interconnections required for a dual user configuration  
Most of the connections are similar to the standard configuration. The main difference is in the links to the second local module.  
Use an audio link lead to connect the audio out socket of the first local module to the audio in socket of the second. Similarly, use  
a video link lead to connect the video out and video in ports. The second local module then requires its own USB link directly to  
the computer. In all other respects follow the standard instructions to connect CATx links and all of the remote module connec-  
tions.  
724-746-5500 | blackbox.com  
Page 21  
ServSwitch Wizard VGA/USB  
3.3 Video display (DDC) information  
The Display Data Channel (or DDC) is an industry standard scheme which allows video monitors to declare their capabilities to the  
computer’s video adapter circuitry, allowing the latter to optimise their outputs accordingly. Since the widespread adoption of the  
scheme, video adapters have become increasingly dependent on receiving relevant DDC information during startup, before they  
will output anything more than a rudimentary video signal.  
It is not possible to transmit DDC data back from the video monitor that is attached to the remote module to the computer’s  
video adapter. Therefore, during startup of the local module, it will search for a video monitor connected to its local feed-through  
connector:  
• If a local video monitor is found, its DDC information will be compared to the information already stored and, if different, will  
be copied, stored and presented to the video adapter upon request.  
• If no local video monitor is found, the local module will make available its previously stored set of DDC parameters to the video  
adapter upon request; or, if none were stored, a default set.  
In either case, the DDC information taken by the video adapter will be used to determine the video output that is sent via the  
ServSwitch Wizard VGA-USB modules to the remote monitor.  
If you find that the default DDC information is not completely suitable for your remote monitor, try temporarily connecting your  
remote monitor to the video out port of the local module. When the local module is powered up, it will read and store the DDC  
information from your monitor. You can then return the monitor to its remote position and the new DDC information will be used  
at every power on.  
724-746-5500 | blackbox.com  
Page 22  
Chapter 3: Installation  
3.3.1 DDC indications  
E
L
I
N
K
When power is first applied to the local module (either from the computer’s USB port or an optional power  
adapter) it will search for valid DDC data on its video out connector. During this process, the green indicator  
(built into the link connector) will flash to indicate its progress:  
• If no valid DDC information is located, the green indicator will give one very short flash, representing an  
attempt to read data. No changes will be made to the information already stored within the local module.  
• If the DDC information is the same as that already stored, no change will be made and the green indicator  
will give one single flash as the information is checked and normal operation resumes.  
• If different DDC information is located, the green indicator will flash rapidly for 2 to 3 seconds while the new information is  
stored. A single flash will then be given as the information is checked and normal operation resumes.  
The local module’s green indicator also provides fault indications to assist with troubleshooting:  
• Two flashes - Checksum error prior to copying - no information will be programmed.  
• Three flashes - Too much data to fit into the module - the module can hold a maximum of two pages of DDC information.  
• Rapid flashing followed by four flashes - data was lost during copying - the default data was substituted. Repeat the power on  
process.  
• Rapid flashing followed by five flashes - Checksum error during copying - the default data was substituted. Repeat the power  
on process.  
724-746-5500 | blackbox.com  
Page 23  
ServSwitch Wizard VGA/USB  
3.4 Video compensation  
The ServSwitch Wizard VGA-USB modules include a video compensation system that allows you to get the best results from your  
remote video display(s). Using this special mode you can configure:  
Cable type - Select the type of link cable used.  
Cable length - Enter the length of the link cable.  
Video gain - Alter the signal gain for the image.  
Color skew - Adjust the timing of each color to fine tune the image.  
Expert mode - Please contact Black Box technical support for details.  
What is skew and why is compensation needed?  
The twisted pair cabling supported by the ServSwitch Wizard VGA-USB modules consists of four pairs of wires per cable,  
three of which are used to convey red, green and blue video signals to the remote video monitor. Due to the slight difference  
in twist rate between these three pairs, the red, green and blue video signals may not arrive at precisely the correct times.  
This is visible as separate color shadows on high contrast screen images. This effect is particularly apparent when using higher  
screen resolutions and some types of category 5e cables.  
The video compensation system within the remote module allows you to delay or advance the timing of any of the color  
signals so that they all arrive at the monitor at the correct times.  
Take a close look at a locally connected display. From left to right, groups of pixels are usually arranged in the order: R / G  
/ B and the signals must arrive in the correct order to obtain the optimum screen image. The skewtest.exe pattern (on the  
supplied CD-ROM) in particular helps to highlight the pixel layout by showing very narrow horizontal and vertical lines.  
Test images while compensating  
For best results while adjusting video compensation, arrange a combination of elements  
on the remote display. We suggest the following:  
• Roughly half of the screen to display standard operating system color icons on a mid-  
The  
skewtest.exe  
test pattern  
showing its RGB  
green wallpaper.  
• A quarter screen of the skewtest.exe pattern (available on the supplied CD-ROM).  
crosses. In this case,  
the green signal can be  
seen out of line with the  
• A quarter screen of standard black text on a white background.  
Note: You need to set all of the above BEFORE entering video compensation mode  
other two colors.  
because the USB keyboard will be isolated from the computer.  
724-746-5500 | blackbox.com  
Page 24  
Chapter 3: Installation  
3.4.1 To enter video compensation mode  
1 Ensure that the two ServSwitch Wizard VGA-USB units are connected to the computer and powered on. A USB keyboard must  
be connected to the remote unit.  
2 Arrange your test images on the remote screen. Please refer to the section ‘Test images while compensating’ shown bottom  
left.  
3 On the remote unit, click the miniature switch 1 to its ON position.  
2
1
ON  
The indicators on the keyboard linked to the remote unit will begin to flash in sequence.  
Also, the green indicator adjacent to the CATx link socket will flash.  
Note: During video compensation mode, the keyboard and any other connected USB devices will  
be temporarily isolated from the computer.  
This flash sequence  
indicates that you  
are at Standby level  
You are now at the standby level within video compensation mode.  
From standby, you can choose which adjustments to make. Generally you should set the cable type and cable length options  
first. Then, if necessary, use the video gain and color skew adjustments to fine tune the remote video image.  
Please see the next page for details about each adjustment >>>  
When your adjustments are complete, return the unit to normal operation as described below:  
3.4.2 To exit video compensation mode (return to normal operation)  
1 Ensure that you are at standby level by exiting from any adjustment options.  
2 On the remote unit, return the miniature switch 1 to its OFF position.  
All USB devices will be reconnected to the computer and normal operation will continue.  
724-746-5500 | blackbox.com  
Page 25  
ServSwitch Wizard VGA/USB  
3.4 Video compensation (continued)  
Once you have entered video compensation standby level, you can choose which adjustments to make. Generally you should set  
the cable type and cable length options first. Then, if necessary, use the video gain and color skew adjustments to fine tune the  
remote video image.  
Dual-variants  
By default, all video compensation changes that you make will affect both channels equally. If you wish to adjust the channels  
separately:  
• Enter the video compensation standby level. The green indicators on both link sockets of the remote module will flash.  
• From standby, press . The keyboard indicators will alternate between the Num Lock and Scroll Lock, and the Caps Lock.  
Press  
or  
to select the primary or secondary video display, respectively. The green indicator of the link socket  
corresponding to the chosen video channel will flash (lower=primary, upper=secondary), the other will remain on.  
• Make the required compensation changes to the chosen video channel using the techniques described below.  
• To return to using both channels, from standby, press  
and then press  
The green indicators of both link sockets will flash.  
3.4.3 To set the cable type  
a From standby, press . The Num Lock and Caps Lock indicators will flash.  
b Type the number that corresponds to the category of link cable used:  
• Press  
• Press  
• Press  
• Press  
• Press  
for Cat 5  
for Cat 5e  
for Cat 6  
for Cat 7  
for Cat 7a  
c Press  
to save the value and return to standby.  
Alternatively, press  
to discard any change and return to standby.  
3.4.4 To set the cable length  
a From standby, press . The Caps Lock and Scroll Lock indicators will flash.  
b Use the keypad to enter the cable length in meters.  
c Press  
Alternatively, press  
Note: You can also increase or decrease the cable length setting from the standby level (and view the resulting change in  
screen image quality) using and respectively. If necessary, press to return to a neutral setting. Such adjustments to  
the cable length setting are saved automatically.  
to save the value and return to standby.  
to discard any change and return to standby.  
724-746-5500 | blackbox.com  
Page 26  
Chapter 3: Installation  
3.4.5 To adjust video gain  
a From standby, use  
and  
to decrease or increase the gain level. If necessary, press  
to return to a neutral setting.  
Gain adjustments are saved automatically.  
3.4.6 To adjust color skew  
You will only need to use these adjustments if the video image is not sharp after adjusting the cable type and  
length. Before entering video compensation mode, display the suggested screen content (see Test imag-  
es while compensating on the previous page). Look for color fringes adjacent to the displayed icons  
and text. Also check the skewtest.exe image to confirm whether the red, green and blue  
crosses are all vertically aligned.  
a From standby, press either  
,
or  
depending on which color needs to be adjusted. The Num Lock, Caps Lock or Scroll  
Lock indicators will flash for the Red, Green and Blue channels respectively.  
b Use and to adjust the delay for the chosen color while watching the results on the remote video display.  
Note: If the screen goes blank during adjustment, either press the opposite arrow key to the one you last pressed or press  
to reset all delays.  
c Press  
to save the setting and return to standby.  
to discard any change and return to standby.  
Alternatively, press  
724-746-5500 | blackbox.com  
Page 27  
ServSwitch Wizard VGA/USB  
4. Operation  
4.1 General use  
In use, the ServSwitch Wizard VGA-USB modules should be transparent - the system and its peripherals should operate exactly as  
normal, the only difference being that they are now up to 984 feet (300 meters) apart.  
In some installations, you may see some ‘shadows’ to the right of high contrast screen characters. This can be caused by an incor-  
rect video compensation setting and it may be necessary to make adjustments to correct this. Please see Video compensation in  
the ‘Installation’ section.  
4.2 Dual user arbitration  
When using two sets of ServSwitch Wizard VGA-USB modules to allow two users to access a single computer, be aware that arbi-  
tration between the users is handled by the USB sub-system of the computer. Unlike with other Black Box products, this means  
that both users can control the computer at exactly the same time and the resulting keyboard and mouse influences will be an  
amalgam of the two inputs - i.e. a mouse move to the right by one user will cancel out a simultaneous left mouse move by the  
other. The same is also true when the local module has feed-through peripherals attached to it, adjacent to the computer.  
For this reason, the ServSwitch Wizard VGA-USB dual user arrangement is better suited to situations where two users would not  
often require simultaneous access.  
4.3 Peripheral operation  
4.3.1 USB  
Each ServSwitch Wizard VGA-USB remote module provides four USB outlets, each of which can support USB 2.0 peripherals at  
speeds up to 12Mbps. The ServSwitch Wizard VGA-USB appears to the computer as a four port USB hub.  
If the link between the modules is interrupted, any connected USB peripherals will be automatically disabled and re-enabled once  
the connection is restored.  
[Dual-variant only] Note: When connecting four USB devices to the unit, ensure that their total power requirements do not exceed  
1700mA (1.7A). The USB standard states a maximum allowable current draw of 500mA (0.5A) per device, although most devices  
remain well below this limit - USB keyboards and mice typically require 100mA. Each ServSwitch Wizard VGA-USB module  
contains a self-resetting fuse that will prevent damage by shutting down the unit if the total power draw becomes excessive.  
724-746-5500 | blackbox.com  
Page 28  
Chapter 4: Operation  
724-746-5500 | blackbox.com  
Page 29  
ServSwitch Wizard VGA/USB  
Appendix A. Troubleshooting  
A.1 Status indicators  
The green indicators built into the link connectors on each module provide useful feedback regarding the connection and power  
status:  
During startup (of the local module)  
• One very short green flash: no valid DDC information available from a locally connected video monitor, no changes made to  
stored DDC information.  
• Single green flash: DDC information being read from a locally connected video monitor, but no changes made to stored DDC  
information.  
• Rapid green flash for 2 to 3 seconds, followed by single flash: New DDC information being read and stored from a locally con-  
nected video monitor.  
• Two green flashes - Checksum error prior to copying - no information will be programmed.  
• Three green flashes - Too much data to fit into the module - the module can hold a maximum of two pages of DDC informa-  
tion.  
• Rapid green flashing followed by four flashes - data was lost during copying - the default data was substituted. Repeat the  
power on process.  
• Rapid green flashing followed by five flashes - Checksum error during copying - the default data was substituted. Repeat the  
power on process.  
During operation (either module)  
• Continual yellow: Valid CATx link to other module sensed (on dual-variants, only the indicator of the lower link connector is  
used for this purpose).  
• Continual green: Correct power input sensed.  
Important: The ServSwitch Wizard VGA-USB can be used with other hubs in the system, but please note that due to power con-  
straints, the local unit should not be connected to the downstream port of a bus-powered USB hub. Additionally, dual-variant  
local units must always be powered using their supplied power adapter. Please see section 3.2.1.5 Local module power for details.  
724-746-5500 | blackbox.com  
Page 30  
Appendices  
Appendix B. Safety Information  
• For use in dry, oil free indoor environments only.  
• Do not use to link between buildings.  
• Ensure that all twisted pair interconnect cables are installed in compliance with all applicable wiring regulations.  
• Do not connect CATx link interfaces (RJ45 style connectors) to any other equipment, particularly network or telecommunica-  
tions equipment.  
• Warning – the power adapter contains live parts.  
• No user serviceable parts are contained within the power adapter - do not dismantle.  
• Plug the power adapter into a grounded socket outlet close to the module that it is powering.  
• Replace the power adapter with a manufacturer approved type only.  
• Do not use the power adapter if the power adapter case becomes damaged, cracked or broken or if you suspect that it is not  
operating properly.  
• If you use a power extension cord with the remote module, make sure the total ampere rating of the devices plugged into the  
extension cord do not exceed the cord’s ampere rating. Also, make sure that the total ampere rating of all the devices plugged  
into the wall outlet does not exceed the wall outlet’s ampere rating.  
• Do not attempt to service the modules yourself.  
• The power supply can get warm in operation – do not situate it in an enclosed space without any ventilation.  
724-746-5500 | blackbox.com  
Page 31  
Black Box Tech Support: FREE! Live. 24/7.  
Tech support the  
way it should be.  
Great tech support is just 30 seconds away at 724-746-5500 or blackbox.com.  
®
®
NETWORK SERVICES  
About Black Box  
Black Box Network Services is your source for an extensive range of networking and infrastructure products. You’ll find everything  
from cabinets and racks and power and surge protection products to media converters and Ethernet switches all supported by  
free, live 24/7 Tech support available in 30 seconds or less.  
© Copyright 2012. Black Box Corporation. All rights reserved.  
ACU5250A-R2, rev. 1  
724-746-5500 | blackbox.com  

NEC Server EXPRESS5800 User Manual
Microsoft Sql Server 2008 R2 Small Business Edition C9C00500 User Manual
LG Electronics Wine User Manual
Kenwood CD 324M User Manual
HTC ROSE130 User Manual
Breville BES200 User Manual
Black Box Computer Accessories KV1400AKV1404A User Manual
Audiovox P 48 User Manual
Alpine CDA 105 User Manual
AEG KF 2061 AROMA User Manual