B60 Keurig Brewer B60 User Manual

Owner’s manual  
Special Edition/Signature B60 Keurig® Brewer  
TABLE OF CONTENTS  
IMPORTANT SAFEGUARDS Safe Operation & Use  
CAUTION: There are two sharp needles that puncture the K-Cup® pack, one  
above the K-Cup® Pack Holder and the other in the bottom of the K-Cup® Pack  
Holder. To avoid risk of injury, do not put your fingers in the K-Cup® Pack  
Assembly Housing.  
KEURIG® GOURMET SINGLE CUP HOME BREWING SYSTEM  
Special Edition/Signature B60 —Using Your Brewer  
When using electrical appliances, basic  
safety precautions should be followed,  
including the following:  
11. For best operation, plug the appliance  
into its own electrical outlet on a  
dedicated circuit to prevent flickering  
of lights, blowing of fuses or tripping a  
circuit breaker.  
electrical short circuit, grounding  
reduces the risk of electrical shock.  
19. If the outlet is a standard 2-prong wall  
outlet, it is your personal responsibility  
and obligation to have it replaced with a  
properly grounded 3-prong wall outlet.  
20.Do not, under any circumstances, cut or  
remove the third (ground) prong from  
the power cord or use an adapter.  
21. Consult a qualified electrician if  
the grounding instructions are not  
completely understood, or if doubt  
exists as to whether the appliance is  
properly grounded.  
CAUTION: There is extremely hot water in the K-Cup® Pack Holder during the  
brew process. To avoid risk of injury, do not lift the Handle or open the K-Cup®  
Pack Assembly Housing during the brewing process.  
SET-UP  
1. Read all instructions before using.  
2. Do not touch hot surfaces. Use handles  
and knobs when available.  
Helpful Hints........................................................................................4  
Unpacking ............................................................................................4  
Features ...............................................................................................5  
12. Do not operate any appliance with a  
damaged cord or plug or after  
the appliance malfunctions or is  
damaged in any manner. Contact  
Keurig Customer Service to report  
any malfunction of or damage to the  
Brewer.  
13. Do not let the cord hang over the edge  
of the table or counter, or touch hot  
surfaces.  
14. To disconnect, press the Power Button  
on the Brewer to ‘OFF’ status and then  
remove the plug from the wall outlet.  
15. Close supervision is necessary when  
any appliance is used by or near  
children.  
CAUTION: Please always keep the Brewer in its upright position to avoid  
potential injury and/or damage to your Brewer.  
3. This appliance must be properly  
installed and located in accordance  
with these instructions before it is used.  
4. The use of accessory attachments  
not recommended by the appliance  
manufacturer may result in fire,  
electrical shock or injury to persons.  
5. Do not place on or near a hot gas or  
electric burner, or in a heated oven.  
6. Do not use outdoors.  
7. To protect against fire, electric shock  
and injury do not immerse cords, plugs,  
or the appliance in water or any other  
liquid.  
8. Do not overfill the Water Reservoir  
with water.  
9. Use only water in this appliance! Do  
not put any other liquids or foods in the  
Water Reservoir except as instructed in  
the Cleaning Instructions in this guide.  
10. Turn off and unplug the Brewer before  
cleaning or maintenance. Allow to cool  
before putting on or taking off parts  
and before cleaning the appliance.  
SECTION 1SET-UP & FIRST BREW  
Set-Up & First Brew...........................................................................6  
SHORT CORD INSTRUCTIONS: A short power supply cord is provided to  
reduce the risk of becoming entangled in or tripping over a longer cord.  
SECTION 2CONTROLS & INDICATORS  
If an extension cord is used, (1) the marked electrical rating of the cord set or  
extension cord should be at least as great as the electrical rating of the  
appliance; (2) the cord should be arranged so that it will not drape over the  
countertop or tabletop where it can be pulled on by children or tripped over  
unintentionally; and (3) the extension cord must include a 3-prong grounding plug.  
Setting the Clock...............................................................................10  
Programming On/Off Features ......................................................10  
Programming Brew Temperature .................................................12  
22.Do not use the appliance for other than  
its intended use.  
SECTION 3CLEANING & MAINTENANCE  
Cleaning..............................................................................................12  
De-Scaling..........................................................................................13  
Storage ...............................................................................................14  
SavE THESE  
THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.  
INSTRUCTIONS.  
WaRNING TO USERS aND PaRENTS  
1. DO NOT permit children to use Brewer  
unless there is adult supervision. Brewer  
dispenses very hot water.  
WARNING  
THIS PRODUCT CONTAINS CHEMICALS, INCLUDING  
16. Do not lift the Brewer Handle while  
brewing is in progress.  
17. Always keep the Water Reservoir Lid  
on the Water Reservoir unless you are  
refilling it.  
SECTION 4TROUBLESHOOTING..................................................15  
LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER,  
BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.  
SECTION 5 WARRANTY................................................................16  
2. SPECIaL NOTICE FOR HOT COCOa USERS:  
IMMEDIaTELY aFTER USING a HOT COCOa  
K-CUP® PaCK, RUN a Hot Water Brew Cycle  
without a K-Cup® pack to avoid the possibility  
of clogging the exit needle. DO NOT assume  
the next user will do this.  
Record your Brewer Serial Number here.  
See Unpacking Instructions on page 4 for serial number location.  
18. This appliance is equipped with a power  
cord having a grounding wire with a  
grounding plug. The appliance must  
be grounded using a 3-hole properly  
grounded outlet. In the event of an  
WARNING: TO REDUCE THE RISK OF FIRE OR  
ELECTRIC SHOCK, DO NOT REMOVE THE  
BOTTOM COVER. NO USER SERVICEABLE  
WARNING  
RISK OF FIRE OR  
PARTS ARE INSIDE. REPAIR SHOULD BE DONE  
ELECTRIC SHOCK  
Removing the serial number label from the Brewer will void warranty.  
!
DO NOT OPEN  
BY AUTHORIZED SERVICE PERSONNEL ONLY.  
2
3
Set-Up  
Features Special Edition/Signature — Model B60 Brewer  
4. Customize the size, flavor & brew that’s  
perfect for you.  
2. Remove enclosed literature.  
Helpful Hints  
T
D
G
3. Turn the box on its side with front of box  
face down.  
With the choice of over 200 varieties of  
K-Cup® packs and 3 brew sizes (Small Cup-  
5.25 oz., Small Mug-7.25 oz. and Large  
Mug-9.25 oz.), your Keurig® Brewer gives you  
endless options to customize the size, flavor  
and brew that’s perfect for you. For a strong,  
intense cup, select an Extra Bold K-Cup®  
pack (with up to 30% more ground coffee than  
regular varieties) and brew size that’s right  
for you. The smaller the brew size, the more  
intense flavor in your cup. The larger the brew  
size, the less intense flavor in your cup.  
1. Plug Brewer into its own grounded outlet.  
If the electric circuit is overloaded with other  
appliances, your Brewer may not function  
properly. The Brewer should be operated on  
its own circuit, separate from other appliances.  
a
4. Reach into the box and grasp the plastic bag  
that contains the Brewer.  
READY  
TO BREW  
M
5. Carefully pull the plastic bag (and packaging  
materials) toward you and out of the box. The  
Brewer will still be encased in the polyfoam  
and be on its side.  
S
:
11 56  
AM  
2. Keep your Brewer turned “ON.”  
F
MENU  
H
To brew a fresh cup of coffee, tea or hot cocoa  
anytime you want, keep your Brewer turned  
“ON” all the time. However, the Brewer is fully  
programmable so you can set it to turn on and  
off automatically to match your schedule.  
Or, if you prefer, set the Brewer to automatically  
turn off after a period of time. Follow the simple  
instructions on pages 10–12 to find the settings  
that are most convenient for you.  
E
C
I
R
B
6. Remove the top polyfoam packaging material.  
7. Carefully lift Brewer off of the bottom polyfoam  
and place it upright on a flat, steady surface.  
N
J
5. Remove K-Cup® pack after use.  
Please see page 7 for brewing instructions.  
8. Lift plastic bag off of Brewer.  
9. Record the serial number for this Brewer on  
page 3 of this guide. The serial number can  
be found on the bottom of the Brewer box or  
on the Brewer behind the Drip Tray (when  
removed).  
6. Brewing into a travel mug.  
0
P
Q
K
To brew into a travel mug, simply remove the  
Drip Tray Assembly and place the travel mug  
on the Drip Tray Base.  
3. For the best tasting gourmet coffee, tea or  
hot cocoa, Keurig recommends using bottled  
or filtered water.  
L
Water quality varies from place to place.  
If you notice an undesirable taste in your cup  
of coffee, such as chlorine or other mineral  
tastes, we recommend you consider using  
bottled water or water from a filtration  
system. For best results, carefully follow  
manufacturer’s instructions when using any  
water filtration system.  
7. De-scale Brewer regularly.  
Please see pages 13 and 14 for instructions.  
10. Place the Brewer upright on a flat, steady  
surface. Remove tape holding Water Reservoir  
in place.  
Special Edition/Signature B60 Brewer  
Controls and Indicators  
A. Water Reservoir Lid  
B. Water Reservoir  
C. Water Reservoir  
Lock Tab Slots  
D. Handle  
F. K-Cup® Pack Holder  
(E and F are the K-Cup®  
Pack Holder Assembly)  
G. Lid  
J. Drip Tray Plate  
K. Drip Tray  
L. Drip Tray Base  
M. Vent  
O. Small Cup Button 5.25 oz.  
P. Small Mug Button 7.25 oz.  
Q. Large Mug Button 9.25 oz.  
R. Menu Button  
S. LCD Control Center  
T. Power Button  
Unpacking Instructions  
We recommend you save all packing materials in  
case future shipping of the product is necessary.  
1. Place Brewer box on a large steady surface  
(such as a table or countertop) or on the floor.  
Open the box.  
H. K-Cup® Pack  
Assembly Housing  
I. Housing  
N. Power Cord  
WARNING:  
Keep all plastic bags away  
from children.  
E. Funnel  
4
5
SECTION 1 Set-Up & First Brew  
8. The Brewer will automatically fill the  
internal tank with water and then the water  
will be heated. This will take about 4 minutes.  
During the heating period, “NOT READY”  
(fig. 4) is indicated on the LCD Control  
Center. Do not lift Handle during this  
heating period.  
Ready to Brew Your First Cup  
IMPORTaNT: You cannot use your Keurig® Brewer until  
2
fig.  
fig.  
4
fig.  
Lock Tabs  
6
4. Fill Water Reservoir with bottled or filtered  
water so that the water level is just below the  
top edge of the Water Reservoir.  
1. LCD Control Center will indicate  
“READY TO BREW.”  
it has been set-up for its first use as set forth below.  
NOTE: If Brewer has been exposed to temperatures  
below freezing, allow Brewer at least two hours to  
reach room temperature before brewing. A frozen  
or extremely cold Brewer will not operate.  
NOT READY  
2. Place a cup or mug on the Drip Tray Plate.  
5. Place Water Reservoir base into the left side  
of the Brewer and be sure the Water Reservoir  
Lock Tabs engage with the Brewer. Replace  
Lid on Water Reservoir.  
3. Lift the Handle and the K-Cup® Pack Holder  
will open toward you (fig. 6).  
Once the water is heated, “READY TO BREW”  
will be indicated and the Brew Buttons will be  
illuminated (fig. 5). NOTE: You may see small  
amounts of water coming from the Vent and  
dripping into the Water Reservoir during this  
and subsequent heating—this is normal.  
4. Select a K-Cup® pack.  
NOTE: Do not remove the foil  
lid or puncture the K-Cup® pack.  
6. Press the Power Button found directly  
above the LCD Control Center (fig. 3).  
fig.  
1
5. Place a K-Cup® pack in the  
K-Cup® Pack Holder (fig. 7).  
Setting Up Your Brewer  
7. The LCD Control Center will illuminate and  
indicate “NOT READY.NOTE: A K-Cup® pack  
should not be used for this sequence.  
1. Unwrap cord and plug the Brewer into  
a grounded outlet. Remove all pieces of  
packing tape and clear plastic sticker  
from LCD Control Center.  
CAUTION: There are two sharp needles that  
puncture the K-Cup® pack, one above the  
K-Cup® Pack Holder and the other in the bottom  
of the K-Cup® Pack Holder. To avoid risk of  
injury, do not put your fingers in the K-Cup®  
Pack Assembly Housing.  
9. Lift and lower the Handle. Press the Small  
Mug Button to start a cleansing brew. Pour  
the hot water into the sink.  
fig.  
3
fig.  
5
NOTE: If the Water Reservoir is empty or  
not in place on the Brewer, the LCD Control  
Center will also indicate “ADD WATER.None  
of the buttons will be activated until water  
is added to the Water Reservoir and Water  
Reservoir is in place.  
Power  
fig.  
7
10. The one-time set-up process is now  
complete and you are ready to brew!  
NOTE: The Brewer may take 15 seconds  
between brews and then “READY TO BREW”  
will be indicated.  
NOT READY  
READY  
2. Place a large mug (10 oz. minimum) on the  
Drip Tray Plate.  
TO BREW  
ADD  
WATER  
MENU  
3. Remove the Water Reservoir from Brewer  
by first removing Lid from Reservoir (fig. 1),  
then lifting Reservoir straight up and away  
from Brewer (may be tight), (fig. 2). Rinse  
with fresh water.  
6. Lower the Handle to close the Lid over the  
K-Cup® Pack Holder. (When it is closed  
completely, the LCD Control Center will  
indicate “READY TO BREW” and the Small  
Cup, Small Mug and Large Mug Buttons will  
flash for up to 60 seconds.)  
Small  
Mug  
6
7
SECTION 1 Set-Up & First Brew  
Ready to Brew Your First Cup (Continued)  
10. Lift the Handle, remove and dispose of the  
used K-Cup® pack. CAUTION: K-Cup® pack  
will be hot.  
adding Water  
Brewing Hot Water  
7. Choose the cup size of coffee, tea or hot  
cocoa by pressing the button that indicates  
your choice. The Small Cup choice will yield  
a 5.25 oz. serving, the Small Mug choice will  
yield a 7.25 oz. serving and the Large Mug  
choice will yield a 9.25 oz. serving. NOTE: If  
you do not push a Brew Button in 60 seconds,  
the LCD Control Center will return to “READY  
TO BREW” and the Brew Buttons will be  
disabled to prevent accidental activation.  
Re-activate the Brew Buttons by raising and  
lowering the Handle completely.  
The LCD Control Center will indicate “ADD  
WATER” when the water level in the Water  
Reservoir is low or if the Water Reservoir has  
been removed (fig. 8). The blue light in the Water  
Reservoir will also blink when water needs to be  
added. The Brewer will not allow you to brew when  
ADD WATER” is indicated.  
Your Brewer is able to produce hot water for making hot cocoa from a packet,  
for use in cooking, for making soups, etc. Simply follow the instructions on  
page 7 — “Ready To Brew Your First Cup” without adding a K-Cup® pack.  
NOTE: After brewing a hot cocoa K-Cup® pack, we recommend running a  
cleansing brew without a K-Cup® pack.  
fig.  
8
11. Enjoy your first cup of Keurig Brewed®  
Small Cup  
gourmet coffee, tea or hot cocoa!  
(5.25 oz.)  
12. Your Brewer may indicate “NOT READY” as it  
heats water for the next brew cycle. The  
“READY TO BREW” indication will return to  
the LCD Control Center in about 15 seconds.  
NOTE: Following the brew, your Brewer will  
fill in preparation for the next brew. The pump  
will make a vibrating sound. This is normal.  
NOT READY  
ADD  
WATER  
Purging the Brewer  
The Water Reservoir can be filled in two ways.  
1. Lift off the Water Reservoir Lid and pour water  
directly into the Water Reservoir while it is still  
attached to the Brewer, then replace the Lid.  
If your Brewer has not been used for more than one week, you should purge  
the water from the inner tank.  
Small Mug  
(7.25 oz.)  
1. If there is water in the Water Reservoir, remove the Lid, then lift the  
Water Reservoir straight up and away from Brewer. Discard water, rinse  
and refill with water. Place the Water Reservoir back on the Brewer and  
replace the Lid. (If there is no water in the Water Reservoir, simply refill.)  
2. Remove the Water Reservoir from Brewer by first removing Lid from  
the Water Reservoir, then lifting the Water Reservoir straight up and  
away from Brewer. Fill with water. Place the Water Reservoir back on  
the Brewer and replace the Lid. IMPORTANT: Do not remove the  
Water Reservoir during the brewing process.  
8. The LCD Control Center will indicate  
“BREWING” and the cup size you selected  
will illuminate. CAUTION: There is extremely  
hot water in the K-Cup® Pack Holder during the  
brew process. To avoid risk of injury, do not lift  
the Handle or open the K-Cup® Pack Assembly  
Housing during the brew process.  
Stopping the Brew Process  
If you need to stop brewing after the process has started, press the Power  
Button to turn the Brewer off. The flow of coffee, tea or hot cocoa will stop,  
the heating element will shut off, and the blue lights illuminating the brew  
buttons and Water Reservoir will disappear. NOTE: You may get less coffee, tea  
or hot cocoa in your cup during your next brew. We recommend that you perform  
a cleansing brew after a terminated brew. Then your NEXT brew will be the  
volume you have selected.  
2. Be sure the Brewer is turned on. Raise and lower the Handle on the  
Brewer without inserting a K-Cup® pack.  
Large Mug  
(9.25 oz.)  
3. The LCD Control Center will indicate “READY TO BREW” and the Small  
Cup, Small Mug and Large Mug Buttons will flash. Be sure to have a  
large mug on the Drip Tray Plate and then press the Large Mug Button.  
Brewing Iced Beverages  
9. There may be a short pause prior to coffee  
being dispensed. The entire brew process  
lasts for approximately 1 minute and ends  
with a burst of air to remove all liquid from  
the K-Cup® pack.  
Your iced tea and iced coffee taste best when fresh-brewed hot over ice. Try it by  
placing a tall cup filled with ice on the Drip Tray Plate (the Drip Tray Assembly  
can be removed to accommodate taller cups), choose your favorite K-Cup®  
pack and press your preferred cup size. Also, look for the Brew Over Iceicon  
on K-Cup® packs that are specially crafted to brew over ice! IMPORTANT: Do not  
brew into a cup made of glass. Doing so may cause the glass to crack or break.  
4. Repeat steps 2 and 3 one more time to completely purge water from  
inner tank.  
If you are experiencing any problems with your Brewer, please contact  
Customer Service at 1.866.901.BREW (2739).  
8
9
c. After setting the desired Auto Off time, press  
the Menu Button four times to scroll through  
the remaining programming options and exit  
the programming mode. “AUTO OFF SET”  
(fig. 11) will now be indicated to confirm that  
it has been set.  
e. If you want to set an “OFF TIME,” repeat the  
procedure above in steps b & c to set your  
desired “OFF TIME.”  
fig.  
fig.  
13  
11  
SECTION 2 Controls & Indicators (LCD Control Center)  
f. To complete the process, press the Menu Button  
two more times to exit the programming mode.  
The LCD Control Center will indicate the options  
you have set.  
Setting the Clock  
Programming On/Off Features  
READY  
TO BREW  
AUTO OFF SET  
CLOCK  
AUTO OFF  
SET  
OFF TIME  
BREW TEMP  
Setting the clock is optional. When the clock is set, the time will appear in  
the LCD Control Center. NOTE: You must set the clock if you will be using the  
On/Off Time programming feature.  
The Brewer provides three modes so that you can enjoy gourmet coffee, tea  
or hot cocoa on your own schedule. By programming your Brewer to turn on  
each morning, you will never have to wait for the Brewer to warm up to brew  
a gourmet cup of coffee.  
AM  
PM  
d. To cancel the Auto Off feature, press the  
Menu Button twice to reach the Auto Off  
programming mode. Press and release the  
Small Cup Button under the blinking “H”  
to advance one hour at a time until “OFF”  
is indicated.  
:
11 56  
AM  
MENU  
MENU  
g. The On Time and Off Time functions operate  
independently from one another. To cancel  
either set function, follow the steps above and  
use the “H” and “M” buttons to advance to 12:00  
AM. Make sure the M button is set to :00, then  
change the “H” button. When you reach 12:00  
AM, the Control Center will indicate “OFF” and  
the function will be disabled.  
1. Press the Menu Button.  
fig.  
9
1. Leave it ON all the time. The Brewer can be left on all the time so that it is  
always ready to brew a fresh cup of gourmet coffee, tea or hot cocoa. To turn  
the Brewer off at any time, simply press the Power Button. (NOTE Although  
the clock remains on if set, you can not brew a cup of coffee, tea or hot cocoa.)  
Press the Power Button again to restore power to the Brewer. You will have  
to wait for the water to heat up before the Brewer is ready to brew.  
2. The word “OFF” will appear at the bottom  
of the LCD Control Center to indicate that  
the clock is not set. The programming  
options will appear on the LCD Control  
Center with a small arrow pointing to “SET  
CLOCK” (fig. 9). “H” (Hour) and “M” (Minute)  
will appear and blink.  
:
3. Program your Brewer for a specific On/Off Time. NOTE: To use this  
programming feature, the clock must be set to the correct time. The clock  
will not be displayed unless the time is set.  
SET CLOCK  
fig.  
14  
AUTO OFF  
ON OFF TIME  
BREW TEMP  
MENU  
2. Set the Brewer to Auto Off following a  
:
a. After setting the correct time (required), press  
EXAMPLE If you chose to set the On Time at  
fig.  
Menu  
12  
specified period of time after the last brew.  
the Menu Button three times to program the On  
Time feature. The LCD Control Center will show  
the programming options with a small arrow  
next to “SET ON TIME” (fig. 12).  
6:15 AM and the Off Time for 10:00 PM, then the  
Brewer will be “READY TO BREW” and maintain  
hot water in the tank during that time so that it is  
always ready for you to brew. If you wanted to  
brew outside this window, simply press the Power  
Button and you can brew as soon as the water is  
heated and the “READY TO BREW” is indicated on  
the LCD Control Center.  
READY  
fig.  
3. Press or hold the blue Small Cup Button under  
the blinking “H” until you have reached the  
appropriate hour. If the hour has passed 12,  
the indicator switches from “AM” to “PM.”  
10  
TO BREW  
a. Press the Menu Button twice to program the  
Auto Off feature. The LCD Control Center will  
display the programming options with a small  
arrow next to “SET AUTO OFF” (fig. 10).  
AUTO OFF SET  
ON TIME SET  
:
11 56  
AM  
MENU  
CLOCK  
Set  
Hours  
Set  
Minutes  
AUTO OFF  
SET ON  
TIME  
b. Press or hold the blue Small Cup Button under  
the “H” to scroll through the hours to your  
desired “ON TIME” hour.  
4. Press or hold the blue Large Mug Button under  
BREW TEMP  
CLOCK  
SET AUTO OFF  
AM  
PM  
b. Press or hold the blue Small Cup Button  
under the blinking “H” to advance 1 hour at  
a time, up to 9 hours.  
ON OFF TIME  
BREW TEMP  
:
the blinking “M” to set the minutes.  
11 56  
MENU  
5. When you have reached the correct time, press the Menu Button five  
times to scroll through the remaining programming options and exit  
the programming mode.  
MENU  
c. Press or hold the blue Large Mug Button under  
the “M” to scroll through the minutes to your  
desired “ON TIME” minutes.  
:
NOTE The “AUTO OFF” Timer and the On/Off Time programming options  
operate independently but can also be programmed to work together. For example,  
you can set the On Time function to turn on at 7:00 AM and then set the Auto Off  
Timer function to turn off the Brewer two hours after the last brew (fig. 14).  
Menu  
x2  
6. The correct time should now be displayed in the LCD Control Center.  
NOTE: If power is interrupted to the Brewer by unplugging it, or if power  
is lost, follow the procedure above to reset the time as the clock will not be  
visible until the time is set.  
d. After setting the desired time, press the Menu Button to save the  
“ON TIME” and move to the “SET OFF TIME” (fig. 13).  
10  
11  
2. Cleaning the FunnelThe Funnel can be  
removed from the K-Cup® Pack Holder by  
pulling on it until it snaps off (fig. 17). The Funnel  
is dishwasher safe. To replace it, just snap it  
back onto the K-Cup® Pack Holder Assembly.  
1. Rinse the filter screen with the strong force of water from your faucet.  
2. If you have a sprayer, aim the water spray at the filter screen.  
3. Fill the Water Reservoir with approximately two inches of clean water  
and agitate (shake) the Water Reservoir.  
fig.  
17  
SECTION 2 Controls & Indicators (LCD Control Center)  
SECTION 3 Cleaning & Maintenance  
Cleaning External Parts  
Programming Brew Temperature (187°–192º F)  
Empty the Water Reservoir then fill it with clean water and return it to the Brewer.  
If needed, repeat above procedures. CAUTION: Please rinse the Water Reservoir  
thoroughly after cleaning. This will ensure that no cleaners or cleaning solutions  
remain as they may contaminate the water supply in the Brewer.  
The Brewer brews at a preset temperature of 192°. You can adjust this  
temperature down by 5 degrees if you prefer a cooler cup of coffee, tea  
or hot cocoa. Simply follow the instructions below.  
Regular cleaning of the Brewer’s external components is recommended.  
3. Cleaning the Exit NeedleThe Exit Needle is  
located on the inside bottom of the K-Cup® Pack  
Holder Assembly. Should a clog arise due to  
coffee grinds, it can be cleaned using a paper  
clip or similar tool. Remove K-Cup® Pack Holder  
Assembly and detach Funnel. Insert the paper  
clip (fig. 17) into the Exit Needle to loosen the  
clog and push it out. The K-Cup® Pack Holder is  
dishwasher safe. CAUTION: There are sharp  
1. Never immerse the Brewer in water or other liquids. The Housing and  
other external components may be cleaned with a soapy, damp,  
non-abrasive cloth.  
1. Press the Menu Button on the LCD Control Center five times to  
program the Brew Temperature feature.  
!
2. The Drip Tray can accumulate up to 8 oz. of overflow. The Drip Tray  
and Drip Tray Plate should be periodically inspected and rinsed clean.  
To remove the Drip Tray Assembly, simply slide it toward you, keeping  
it level at all times to avoid spilling. The Drip Tray and Drip Tray Plate  
should not be placed in the dishwasher. They should be cleaned with a  
damp, soapy, non-abrasive cloth and rinsed thoroughly.  
De-Scaling Your Brewer  
2. The LCD Control Center will now display the programming options with  
a small arrow next to “SET BREW TEMP” (fig. 15). Also, the temperature  
192° (initial setting) will be indicated at the bottom of the LCD Control  
Center to indicate the current temperature setting.  
Mineral content in water varies from place to place. Depending on the  
mineral content of the water in your area, calcium deposits or scale may build  
up in your Brewer. Scale is non-toxic, but left unattended, it can hinder Brewer  
performance. De-scaling your Brewer helps maintain the heating element and  
other internal parts of the Brewer that come in contact with water.  
needles that puncture the K-Cup® pack above the K-Cup® Pack Holder and in  
the bottom of the K-Cup® Pack Holder. To avoid risk of injury, do not put your  
fingers in the K-Cup® Pack Assembly Housing.  
3. A minus sign will appear over the Small Cup Button and/or a plus sign  
over the Large Mug Button. Use these buttons to raise or lower the  
temperature one degree at a time.  
Cleaning the K-Cup® Pack Holder assembly  
The Brewer should be de-scaled every 3-6 months  
to ensure optimal performance. It is possible for  
calcium deposits to build up faster, making it  
necessary to de-scale more often.  
Cleaning the Water Reservoir & Water Reservoir Lid  
4. Once you have reached your desired brew  
1. Cleaning the PartsThe K-Cup® Pack Holder  
fig.  
15  
fig.  
18  
fig.  
16  
temperature, press the Menu Button once  
to exit the programming mode. “BREW TEMP  
SET” will be indicated in the LCD Control  
Center if you have changed it from 192°.  
Assembly can be placed onto the top shelf of a  
dishwasher. NOTE: Use low temperature cycles  
in the dishwasher. To remove from the Brewer,  
open the cover by lifting the Handle. Grasp the  
top of the K-Cup® Pack Holder with one hand  
while pushing up on the bottom of the K-Cup®  
Pack Holder from underneath with the other  
until it releases (fig. 16). After cleaning, align the  
K-Cup® Pack Holder with the opening using the  
two front ribs as a guide, and snap into place  
from the top.  
The Water Reservoir Lid and Water Reservoir should be periodically  
inspected and cleaned.  
You should promptly de-scale if “DE-SCALE” is  
indicated on the LCD Control Center (fig. 18).  
However, even if “DE-SCALE” is not indicated,  
you should continue to de-scale your Brewer  
every 3-6 months. Properly follow the de-scaling  
procedure described on page 14.  
The Water Reservoir Lid or Water Reservoir should not be put into the  
dishwasher. They should be cleaned with a damp, soapy, non-abrasive  
cloth and rinsed thoroughly. Do not dry the inside of the Water Reservoir  
with a cloth as lint may remain.  
CLOCK  
AUTO OFF  
ON OFF TIME  
SET BREW TEMP  
5. To change the brew temperature again, repeat  
steps 1 through 3 to change the temperature  
up or down, remembering that the temperature  
can only be between 187° and 192°.  
DE-SCALE  
AM  
:
192°  
11 56  
MENU  
MENU  
To clean the filter screen at the base of your Water Reservoir, empty  
the Water Reservoir and follow one or all of the following procedures.  
NOTE: If you are using a water filter inside the Water Reservoir, remove  
it before cleaning.  
12  
13  
SECTION 4 Troubleshooting  
SECTION 3 Cleaning & Maintenance (continued)  
SITUaTION SOLUTION  
SITUaTION SOLUTION  
De-Scaling Instructions  
A. PREPARE  
Service  
Brewer does not Plug Brewer into an independent outlet.  
have power Check to be sure that it is plugged in securely.  
Plug into a different outlet.  
Brewing a The Exit Needle may be clogged (refer to page 13).  
partial cup Clean the K-Cup® Pack Holder if necessary and rinse  
under faucet (refer to page 12).  
Beyond these recommended cleaning and maintenance procedures, this  
Brewer is not user serviceable. For service, please refer to the Warranty  
section of this guide.  
Step 1: To begin, you will need the following:  
At least 48 oz. of undiluted white vinegar  
Access to an empty sink  
Reset your home’s circuit breaker, if necessary.  
Make sure that the Power Button has  
been turned on.  
The Water Reservoir may have been removed during  
brewing. Replace the Water Reservoir and perform a  
cleansing brew without a K-Cup® pack.  
A large ceramic mug (do not use a paper cup)  
Storage  
Step 2: Empty the water from the Water Reservoir.  
Step 3: Disable Auto Off features.  
De-scale the Brewer (refer to page 13).  
Brewer will After placing the K-Cup® pack in the K-Cup® Pack Holder,  
If you have repeated the de-scale procedure on  
your Brewer two times and it is still only brewing  
a partial cup, contact Customer Service at  
Empty the Water Reservoir before storing, and take care to ensure that you  
store your Brewer in a safe and frost free environment. Please be sure to  
store your Brewer in its upright position to avoid water leakage from the inner  
tank. If you store the Brewer in a cold environment, you run the risk of water  
freezing inside the Brewer and causing damage. When you prepare to use it  
after storage, we recommend rinsing the Water Reservoir with fresh water  
and running three cleansing brews without a K-Cup® pack.  
not brew  
make sure the Handle is pushed down securely and the  
LCD Control Center indicates “READY TO BREW” with the  
three Brew Buttons blinking, then press the Small Cup,  
Small Mug or Large Mug Button.  
B. FILL AND CLEAN  
Step 1: Pour approximately 48 oz. of the vinegar into the Water Reservoir.  
1.866.901.BREW (2739).  
Step 2: Place a large mug on the Drip Tray Plate and run a cleansing brew.  
DO NOT USE A K-CUP® PACK, just press a Brew Button.  
Pour the contents of the large mug into the sink.  
If the LCD Control Center indicates “ADD WATER,” add  
water to the Water Reservoir or make sure the Water  
Reservoir is seated properly in its base.  
If the LCD Control Center indicates “ADD WATER”  
even after refilling, contact Customer Service at  
1.866.901.BREW (2739).  
The Exit Needle may be clogged (refer to page 13).  
If the LCD Control Center indicates “PRIME” and the  
blue light in the Water Reservoir is flashing, see below.  
The time is not The time will not be displayed on the LCD Control  
displayed on the  
LCD Control Center  
Center unless you have set it. To set the clock, follow  
the procedure on page 10.  
Step 3: Repeat the brew process without a K-Cup® pack until “ADD WATER”  
If you plan to move your Brewer to a different location, turn the Brewer  
off, unplug it, and empty the Water Reservoir. If your Brewer has been in  
an environment below freezing, please be sure to let it warm to room  
temperature for at least 2 hours before using.  
is indicated.  
If power is interrupted to the Brewer, you will need to  
set the clock again using the procedure on page 10.  
Step 4: Now let the Brewer stand for at least 4 hours while still on.  
Step 5: Discard any residual vinegar and rinse the Water Reservoir thoroughly.  
My Brewer shuts Check to make sure that the Auto Off Timer  
C. RINSE  
off or turns on  
automatically  
and/or On/Off Time features have not been set. To  
do this, press the Menu Button and scroll through  
the programming options. “OFF” should be indicated  
for Auto Off Timer and On/Off. If “OFF” is not  
indicated, follow directions on page 10 to reset.  
Step 1: Ensure the Water Reservoir is filled with fresh water.  
Step 2: Place a large mug on the Drip Tray Plate and run a cleansing brew.  
Pour the contents of the large mug into the sink.  
LCD Control Center Completely remove the Water Reservoir and  
Step 3: Repeat brew process until “ADD WATER” is indicated.  
indicates “PRIME”  
and the blue light in  
the Water Reservoir  
is flashing  
thoroughly clean (refer to page 13). Ensure the  
Water Reservoir is fully filled with water. Return it to  
the Brewer and ensure it is seated properly.  
If you have completed the above procedure two times  
and this situation persists, contact Customer Service  
at 1.866.901.BREW (2739).  
Step 4: You may need to perform additional cleansing brews if you notice any  
residual taste.  
NOTE: If “DE-SCALE” is still indicated after completing the procedure,  
repeat the de-scaling procedure above.  
If any problems persist, contact Customer Service at 1.866.901.BREW (2739)  
14  
15  
SECTION 5 Warranty  
Limited One Year Warranty  
Nor does this warranty cover damages caused by use of non Keurig Brewed®  
K-Cup® brand packs or accessories, services performed by anyone other  
than Keurig or its authorized service providers, use of parts other than  
genuine Keurig parts, or external causes such as abuse, misuse,  
inappropriate power supply or acts of God.  
Keurig, Incorporated warrants that your Brewer will be free of defects in  
materials or workmanship under normal home use for one year from the date  
of purchase. It is recommended that you fill out and return the warranty card  
enclosed with your Brewer so that your purchase information will be stored  
in our system. Keurig will, at its option, repair or replace a defective Brewer  
without charge upon its receipt of proof of the date of purchase. If a  
Other Limitations  
replacement Brewer is necessary to service this warranty, the replacement  
Brewer may be new or reconditioned. If a replacement Brewer is sent, a new  
limited one year warranty will be applied to the replacement Brewer.  
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS  
WARRANTY, WHETHER WRITTEN OR ORAL. IN ADDITION, KEURIG HEREBY  
SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO  
YOUR B60 BREWER, INCLUDING ANY IMPLIED WARRANTY OF  
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Some  
states or provinces do not allow disclaimers of such implied warranties or  
limitations on how long an implied warranty lasts, so the above limitation  
may not apply to you depending on the state or the province of purchase.  
This warranty only applies to Brewers operated in the United States and  
Canada. This warranty gives you specific legal rights, and you may also have  
other rights that vary from state to state and, in the case of Canada, from  
province to province.  
Only the use of Keurig Brewed® K-Cup® brand packs and accessories will  
guarantee the proper functioning and lifetime of your Keurig® Brewer. Any  
damage to or malfunction of your Brewer resulting from the use of non  
Keurig Brewed® K-Cup® brand packs and accessories may not be covered by  
this warranty or may result in a service fee if the damage or malfunction is  
determined to be caused by such use.  
How do you obtain warranty service?  
Keurig® Brewers are high-quality appliances and, with proper care, are  
intended to provide years of satisfying performance. However, should the  
need arise for warranty servicing, simply call Keurig Customer Service at  
our toll free phone number 1.866.901.BREW (2739). Please do not return your  
Brewer for servicing without first speaking to Keurig Customer Service to  
obtain an Authorization to Return number (ATR). Keurig® Brewers returned  
without an ATR number will be returned to the sender without servicing.  
What is not covered by the Limited Warranty?  
THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL  
DAMAGES SUCH AS PROPERTY DAMAGE AND DOES NOT COVER  
INCIDENTAL COSTS AND EXPENSES RESULTING FROM ANY BREACH  
OF THIS WARRANTY, EVEN IF FORESEEABLE. Some states or provinces  
do not allow the exclusion or limitations of incidental or consequential  
damages, so the above limitation or exclusion may not apply to you  
depending on the state or province of purchase.  
Keurig, Incorporated  
55 Walkers Brook Drive  
Reading, MA 01867  
1.866.901.BREW (2739)  
16  

Nespresso Coffeemaker EF 473 User Manual
Motorola I886 User Manual
Marantz CD5000 User Manual
Magnavox AZ7275 User Manual
Logitech Dock S400i User Manual
Kyocera Opal S14 User Manual
Kenwood DP M6650 User Manual
Intel SSDSA2SH064G1C5 User Manual
Hitachi Travelstar HTS543232A7A384 User Manual
Hamilton Beach D45012W User Manual