INSTALLATION MANUAL
P-105
AM/FM/MPXRADIO
WITHCOMPACTDISCPLAYER,
CD CHANGER CONTROLS
ANDQUARTZCLOCK
WIRING COLOR CODES
FUNCTION COLOR
+ 12 V Acc/Ignition
+ 12 V Battery/Memory
Ground
Red
Yellow
Black
Dimmer
Orange
White
LF + Speaker
LF - Speaker
LR + Speaker
LR - Speaker
RF + Speaker
RF - Speaker
RR + Speaker
RR - Speaker
White/Black
Green
Green/Black
Gray
Gray/Black
Violet
Violet/Black
TYPICAL GM APPLICATION (See Figure 1.)
Radio Preparation:
NOTE: For GM car installations, use the GM Hardware Kit, Part Number 150-1343, which is furnished with the radio.
1. Match quickie bolt locations on the P-105 radio to the factory radio bolt locations, and snap the short quickie bolts (Item #2)
into the appropriate locations.
2. Attach the original factory brackets or those from the radio mounting kit (if required) to the P-105 radio using the supplied
flange nuts (Item #4), or use the enclosed brackets (Item #6) if the original factory brackets are not removable. Additionally,
four brass spacers bave been provided to raise the bracket height as required. Simply place the spacer on the quickie bolt
and secure the mounting bracket.
3. Some vehicle applications incorporate a rear mounting support. Remove the rubber rear bushing from the factory radio.
Match the rear quickie bolt on the P-105 radio to the rear factory radio bolt location and snap the long quickie bolt (Item #3)
into place. Thread the rubber rear bushing from the factory radio onto the P-105 long quickie bolt.
4. Plug supplied wire harness (Item #1) into the mating socket on the rear of the P-105.
Installation:
1. Connect the wiring harness from the radio to the vehicle side radio harness.
2. Plug the factory antenna cable into the antenna socket on the radio.
NOTE: GM vehicles 1992 and up will require an antenna adapter cable to convert the vehicle mini connector to a standard
connector. Antenna adapter cables are available at car stereo speciality shops.
3. If a compatible CD changer is to be used with this radio, connect the cable from the changer to the 8-pin mating socket on
the radio. If an external amplifier will be used for the rear speakers, connect the low-level output RCA leads from the radio
to the low-level inputs on the amplifier.
4. Reconnect the battery and perform a brief functional test of the radio to verify proper performance.
5. After verification, turn off the ignition switch and fasten the radio to the sub-dash using the mounting hardware previously
removed from the factory radio.
6. Re-assemble the dash using the reverse of the disassembly procedure.
-3-
WIRING DIAGRAM-TYPICAL INSTALLATION FOR GM (Figure 1)
-4-
TYPICAL CHRYSLER APPLICATION (See Figure 2.)
Radio Preparation:
NOTE: For Chrysler car installations, use the Chrysler Hardware Kit, Part Number 150-1344, which is furnished with
the radio.
1. Select two of the four mounting tabs provided and match the radio mounting style of the vehicle as shown in Figures 3, 4 and 5.
NOTE: The tab number is stamped on the bottom of the tab.
2. Attach the mounting tabs to the radio chassis with the four small Phillips-head screws provided ( Item # 9).
3. Attach the 14-pin connector from the harness to the radio.
4. Plug the antenna cable into the antenna socket on the radio.
Installation:
1. Attach the ring lug on the ground wire (black) from the radio side harness along with the vehicle side grounding strap to the
rear of the radio chassis using the short quickie bolt (Item #2) and the flange nut (Item # 4) provided.
2. Connect the mating side of the harness to the vehicle side wiring harness.
3. Connect the vehicle antenna cable to the radio antenna connector.
4. If a compatible CD changer is to be used with this radio, connect the cable from the changer to the 8-pin mating socket on
the radio. If an external amplifier will be used for the rear speakers, connect the low-level output RCA leads from the radio
to the low-level inputs on the amplifier.
5. Reconnect the battery, and perform a brief functional test of the radio to verify proper performance.
6. After verification, turn off the ignition switch and install the radio into the sub-dash of the vehicle using either two 10mm
hex-head screws (not provided), or use the existing factory hardware.
7. Re-assemble the dash using the reverse of the disassembly procedure.
-5-
TYPICAL INSTALLATION FOR CHRYSLER (Figure 2)
-6-
TAB #2
Figure 3
TAB #1
TAB #2
TAB #4
Figure 4
TAB #3
Figure 5
TAB #2
-7-
© 2001 Audiovox Electronics Corp., Hauppauge, NY 11788
128-5914A
|