InstallationꢀInstructionsꢀ
Stepꢀ1:ꢀꢀInputꢀintoꢀtheꢀfactoryꢀradioꢀ
Option #1: Use the factory AUX input.
Purchaseꢀaꢀ1/8”ꢀphono‐to‐phonoꢀ
jackꢀcableꢀtoꢀconnectꢀtheꢀeX‐10ꢀtoꢀꢀ
theꢀfactoryꢀAUXꢀinput.ꢀꢀPartꢀ#ꢀ42‐2607ꢀ
fromꢀRadioꢀShackꢀisꢀaꢀgoodꢀexample.ꢀ
Plugꢀoneꢀendꢀofꢀtheꢀcableꢀintoꢀtheꢀ
vehicle’sꢀfactoryꢀAUXꢀport.ꢀ
Plugꢀtheꢀotherꢀendꢀofꢀtheꢀ1/8”ꢀphonoꢀcableꢀintoꢀꢀ
Theꢀ“auxꢀout”ꢀportꢀonꢀtheꢀeX‐10’sꢀpowerꢀsupply.ꢀ
Selectꢀ“AUX”ꢀasꢀaꢀsourceꢀtoꢀhearꢀiPodꢀorꢀBluetoothꢀ
outputꢀfromꢀtheꢀvehicle’sꢀsoundꢀsystem.ꢀ
Skip to Page 5 to continue the installation>>>
Page 3
InstallationꢀInstructionsꢀ
Stepꢀ1:ꢀꢀInputꢀintoꢀtheꢀfactoryꢀradioꢀ
Option #2: Use the Alpine KWE-155B FM splitter.
PurchaseꢀtheꢀAlpineꢀKWE‐155Bꢀ
FMꢀsplitter.ꢀꢀꢀ
Removeꢀtheꢀvehicle’sꢀ
factoryꢀradio,ꢀandꢀunplugꢀtheꢀ
antennaꢀconnection.ꢀ
Plugꢀtheꢀfactoryꢀantennaꢀconnectorꢀ
intoꢀtheꢀportꢀmarkedꢀ“carꢀantenna”ꢀ
onꢀtheꢀKWE‐155BꢀFMꢀsplitter.ꢀ
Plugꢀtheꢀantennaꢀleadꢀmarkedꢀ“carꢀ
audio”ꢀintoꢀtheꢀfactoryꢀradio’sꢀantennaꢀ
input.ꢀꢀꢀ
Routeꢀtheꢀleadꢀmarkedꢀ“eX‐10”ꢀtoꢀtheꢀ
desiredꢀlocationꢀforꢀtheꢀeX‐10’sꢀpowerꢀꢀ
supply,ꢀandꢀre‐installꢀtheꢀfactoryꢀradio.ꢀ
Page 4
InstallationꢀInstructionsꢀ
Stepꢀ2:ꢀꢀMountꢀtheꢀBluetoothꢀmicrophoneꢀ
AttachꢀtheꢀBluetoothꢀmicrophoneꢀtoꢀtheꢀꢀ
microphoneꢀmountingꢀclipꢀbyꢀpushingꢀ
theꢀmicrophoneꢀontoꢀtheꢀclipꢀasꢀshownꢀ
Clipꢀtheꢀmicrophoneꢀmountꢀtoꢀaꢀspotꢀinꢀtheꢀ
carꢀnoꢀmoreꢀthanꢀ24”ꢀfromꢀtheꢀcustomer’sꢀꢀ
mouth.ꢀ
Goodꢀlocationsꢀincludeꢀtheꢀꢀ
sunꢀvisor,ꢀtheꢀtopꢀofꢀtheꢀA‐pillar,ꢀandꢀtheꢀedgeꢀ
ofꢀtheꢀroof‐mountedꢀcenterꢀconsoleꢀ(ifꢀ
equipped)*ꢀ.ꢀ
Routeꢀtheꢀmicrophoneꢀcableꢀtoꢀtheꢀdesiredꢀ
locationꢀforꢀtheꢀeX‐10’sꢀpowerꢀsupply.ꢀ
*Note:ꢀꢀDoꢀnotꢀinstallꢀtheꢀmicrophoneꢀinꢀanyꢀpositionꢀwhereꢀitꢀcouldꢀinterfereꢀwithꢀtheꢀfunctionalityꢀofꢀ
ꢀꢀairbagsꢀinꢀtheꢀvehicle.ꢀ
Page 5
InstallationꢀInstructionsꢀ
Stepꢀ3:ꢀꢀMountꢀtheꢀeX‐10’sꢀdisplayꢀ
Twistꢀtheꢀsuppliedꢀroundꢀplasticꢀplateꢀtoꢀtheꢀ
baseꢀofꢀtheꢀeX‐10’sꢀdisplay,ꢀandꢀattachꢀtheꢀ
suppliedꢀdouble‐sidedꢀtapeꢀtoꢀthisꢀplate.ꢀ
CleanꢀtheꢀdashꢀareaꢀwhereꢀtheꢀeX‐10’sꢀ
displayꢀwillꢀbeꢀmountedꢀwithꢀtheꢀsuppliedꢀ
alcoholꢀpad.ꢀ
Removeꢀtheꢀbackingꢀfromꢀtheꢀꢀ
double‐sidedꢀtape,ꢀandꢀattachꢀ
itꢀtoꢀtheꢀdashꢀbyꢀpressingꢀ
firmly*.ꢀ
Connectꢀtheꢀmonitorꢀcableꢀtoꢀ
theꢀdisplayꢀbase,ꢀandꢀrouteꢀtheꢀ
monitorꢀcableꢀtoꢀtheꢀdesiredꢀ
locationꢀforꢀtheꢀeX‐10’sꢀ
powerꢀsupplyꢀusingꢀtheꢀ
suppliedꢀcableꢀclampsꢀ
*Note:ꢀꢀThereꢀareꢀmanyꢀcustom‐mountingꢀoptionsꢀforꢀtheꢀeX‐10’sꢀdisplay;ꢀreferꢀtoꢀtheꢀAlpineꢀDealerꢀAdꢀ
Centerꢀforꢀaꢀstep‐by‐stepꢀtutorialꢀshowingꢀhowꢀtoꢀbuildꢀaꢀcustomꢀA‐pillarꢀdisplayꢀmount.ꢀ
Page 6
InstallationꢀInstructionsꢀ
Stepꢀ4:ꢀꢀConnectꢀtheꢀeX‐10ꢀtoꢀ12ꢀvoltꢀpowerꢀ
Purchaseꢀaꢀ12ꢀvoltꢀaccessoryꢀoutletꢀwithꢀaꢀꢀ
femaleꢀcigaretteꢀlighterꢀplug,ꢀlikeꢀthisꢀoneꢀ
fromꢀRadioꢀShackꢀ(Partꢀ#270‐1556).ꢀ
Connectꢀtheꢀaccessoryꢀoutlet’sꢀpowerꢀleadsꢀ
toꢀaꢀswitchedꢀ+12ꢀvoltꢀaccessoryꢀleadꢀinꢀtheꢀ
car,ꢀsuchꢀasꢀtheꢀfactoryꢀcigaretteꢀlighterꢀ
wiring.ꢀ
ScrewꢀtheꢀeX‐10’sꢀpowerꢀcableꢀintoꢀtheꢀ
cigaretteꢀlighterꢀadapter.ꢀ
Plugꢀtheꢀaccessoryꢀoutletꢀintoꢀ
theꢀeX‐10’sꢀcigaretteꢀlighterꢀ
adapter.ꢀ
Routeꢀtheꢀyellowꢀendꢀofꢀtheꢀ
eX‐10’sꢀpowerꢀcableꢀtoꢀtheꢀ
desiredꢀlocationꢀforꢀtheꢀeX‐10’sꢀ
powerꢀsupply.ꢀ
Page 7
InstallationꢀInstructionsꢀ
Stepꢀ5:ꢀInstallꢀtheꢀiPodꢀcableꢀ
Findꢀaꢀconvenient,ꢀhiddenꢀ
locationꢀtoꢀplaceꢀtheꢀ
customer’sꢀiPod,ꢀsuchꢀasꢀtheꢀ
centerꢀconsoleꢀorꢀtheꢀgloveꢀ
box.ꢀ
RouteꢀtheꢀsuppliedꢀiPodꢀcableꢀ
toꢀtheꢀdesiredꢀlocationꢀforꢀtheꢀ
eX‐10’sꢀpowerꢀsupply.ꢀ
Page 8
InstallationꢀInstructionsꢀ
Stepꢀ6:ꢀꢀConnectꢀtheꢀeX‐10’sꢀpowerꢀsupplyꢀ
Plugꢀtheꢀmonitorꢀcableꢀintoꢀtheꢀ
portꢀonꢀtheꢀeX‐10’sꢀpowerꢀsupplyꢀ
markedꢀ“monitor”.ꢀ
PlugꢀtheꢀiPodꢀcableꢀintoꢀtheꢀportꢀ
markedꢀ“iPod”.ꢀ
Plugꢀtheꢀ“eX‐10”ꢀoutputꢀfromꢀ
theꢀKWE‐155BꢀFMꢀsplitterꢀintoꢀ
theꢀ“antenna”ꢀportꢀ(unlessꢀyouꢀ
areꢀusingꢀtheꢀ“AUXꢀin”ꢀoption)ꢀ
Plugꢀtheꢀmicrophoneꢀcableꢀintoꢀ
theꢀ“microphone”ꢀport.ꢀ
Screwꢀtheꢀyellowꢀendꢀofꢀtheꢀ
powerꢀcordꢀintoꢀtheꢀportꢀ
markedꢀ“powerꢀsupply”.ꢀ
MountꢀtheꢀeX‐10’sꢀpowerꢀ
supplyꢀinꢀaꢀhiddenꢀlocation.ꢀ
Page 9
InstallationꢀInstructionsꢀ
Stepꢀ7:ꢀꢀSetꢀupꢀtheꢀeX‐10ꢀtoꢀworkꢀcorrectlyꢀ
Stepꢀ7a:ꢀꢀSettingꢀlanguageꢀandꢀoutputꢀmodeꢀ
ConnectꢀtheꢀeX‐10’sꢀdisplayꢀtoꢀtheꢀbaseꢀbyꢀ
pushingꢀdownꢀuntilꢀyouꢀhearꢀaꢀ“click”.ꢀꢀꢀTurnꢀonꢀ
theꢀignitionꢀtoꢀpowerꢀupꢀtheꢀeX‐10.ꢀ
Toꢀselectꢀtheꢀdesiredꢀlanguage,ꢀpushꢀtheꢀ
“setup”ꢀbutton,ꢀthenꢀuseꢀtheꢀ>>Iꢀbuttonꢀtoꢀ
scrollꢀdownꢀtoꢀ“general”.ꢀꢀTapꢀ“enter”ꢀtwice,ꢀ
thenꢀselectꢀyourꢀlanguageꢀusingꢀtheꢀI<<ꢀandꢀ>>Iꢀ
buttons.ꢀꢀTapꢀ“enter”ꢀtoꢀselect.ꢀꢀ
You’reꢀstillꢀinꢀ“setup”ꢀmode,ꢀsoꢀtapꢀtheꢀ>>Iꢀbuttonꢀthreeꢀ
timesꢀuntilꢀyouꢀgetꢀtoꢀ“OutputꢀMode”.ꢀꢀTapꢀ“enter”,ꢀ
andꢀuseꢀtheꢀ>>Iꢀbuttonꢀtoꢀselectꢀ“WireꢀTransmitter”ꢀwhenꢀ
usingꢀtheꢀKWE‐155Bꢀantennaꢀsplitter,ꢀorꢀ“Aux”ꢀwhenꢀusingꢀ
theꢀeX‐10’sꢀauxiliaryꢀoutput.ꢀ
Now,ꢀtapꢀtheꢀꢀꢀꢀbuttonꢀtoꢀgetꢀbackꢀtoꢀtheꢀ“ꢀSetup”ꢀ
menu.ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
Page 10
InstallationꢀInstructionsꢀ
Stepꢀ7:ꢀꢀSetꢀupꢀtheꢀeX‐10ꢀtoꢀworkꢀcorrectlyꢀ
Note:ꢀꢀWhenꢀusingꢀ“Optionꢀ#1”ꢀ(AUXꢀinput)ꢀskipꢀstepꢀ7b
Stepꢀ7b:ꢀꢀSettingꢀtheꢀFMꢀtransmitterꢀfrequencyꢀ
TuneꢀtheꢀcarꢀradioꢀtoꢀanꢀFMꢀfrequencyꢀwhereꢀ
thereꢀisꢀnoꢀradioꢀreceptionꢀ(forꢀexample,ꢀ
104.7).ꢀꢀꢀ
Saveꢀthisꢀasꢀaꢀpreset;ꢀthatꢀwayꢀtheꢀcustomerꢀ
canꢀselectꢀtheꢀpresetꢀstationꢀtoꢀlistenꢀtoꢀiPodꢀorꢀ
BluetoothꢀsoundꢀfromꢀtheꢀeX‐10.ꢀ
Selectꢀ“Transmitter”ꢀfromꢀtheꢀeX‐10’sꢀ“setup”ꢀ
menu,ꢀthenꢀpressꢀandꢀholdꢀ“enter”ꢀforꢀtwoꢀ
seconds.ꢀꢀUseꢀtheꢀ>>IꢀandꢀI<<ꢀbuttonsꢀtoꢀselectꢀtheꢀ
sameꢀfrequencyꢀthatꢀwasꢀpresetꢀintoꢀtheꢀcar’sꢀ
radioꢀ(forꢀexampleꢀ104.7).ꢀꢀꢀ
Pressꢀ“enter”ꢀtoꢀsetꢀthisꢀfrequencyꢀasꢀaꢀpresetꢀinꢀ
theꢀeX‐10.ꢀꢀꢀ
Page 11
InstallationꢀInstructionsꢀ
Stepꢀ7:ꢀꢀSetꢀupꢀtheꢀeX‐10ꢀtoꢀworkꢀcorrectlyꢀ
Stepꢀ7c:ꢀꢀSetꢀupꢀyourꢀcustomer’sꢀBluetoothꢀphoneꢀtoꢀworkꢀwithꢀtheꢀeX‐10ꢀ
Tapꢀtheꢀ“setup”ꢀbutton,ꢀandꢀpressꢀ“enter”ꢀtoꢀ
selectꢀ“Bluetooth”.ꢀꢀPressꢀ“enter”ꢀagainꢀtoꢀ
selectꢀ“pairingꢀmode”,ꢀandꢀaꢀfour‐digitꢀpassꢀ
codeꢀwillꢀbeꢀdisplayedꢀonꢀtheꢀeX‐10.ꢀ
TheꢀeX‐10ꢀisꢀnowꢀdiscoverableꢀandꢀreadyꢀtoꢀ
connectꢀtoꢀyourꢀcustomer’sꢀBluetoothꢀphone.ꢀꢀꢀꢀ
TurnꢀonꢀBluetoothꢀinꢀtheꢀphone’sꢀmenu.ꢀꢀTheꢀphoneꢀ
willꢀaskꢀforꢀaꢀfour‐digitꢀcodeꢀtoꢀconnectꢀwithꢀtheꢀeX‐10,ꢀ
soꢀenterꢀtheꢀcodeꢀshownꢀonꢀtheꢀeX‐10’sꢀscreen.ꢀ
Youꢀwillꢀnowꢀseeꢀaꢀ“connected”ꢀmessageꢀonꢀyourꢀ
phoneꢀtoꢀletꢀyouꢀknowꢀthatꢀyou’veꢀsuccessfullyꢀpairedꢀ
yourꢀphoneꢀwithꢀtheꢀeX‐10*ꢀ
Onceꢀthisꢀisꢀdone,ꢀuseꢀtheꢀ>>Iꢀbuttonꢀtoꢀscrollꢀdownꢀtoꢀ
“HFPꢀSpeaker”.ꢀꢀSelectꢀ“External”ꢀtoꢀhaveꢀBluetoothꢀ
audioꢀplayꢀthroughꢀtheꢀsoundꢀsystem,ꢀorꢀ“Internal”ꢀtoꢀ
haveꢀitꢀplayꢀthroughꢀtheꢀeX‐10’sꢀbuilt‐inꢀspeaker.ꢀ
Nowꢀwe’reꢀallꢀsetꢀup,ꢀsoꢀlet’sꢀuseꢀtheꢀeX‐10>>>ꢀ
*Note:ꢀꢀTurnꢀ“AutoꢀConnect”ꢀonꢀinꢀtheꢀBluetoothꢀsetupꢀmenuꢀifꢀyouꢀwantꢀyourꢀphoneꢀtoꢀautomaticallyꢀconnectꢀtoꢀyourꢀeX‐10ꢀwheneverꢀyouꢀturnꢀ
Page 12
onꢀyourꢀcar’sꢀignition.ꢀ
UsingꢀtheꢀeX‐10ꢀ
Here’sꢀtheꢀbasicsꢀonꢀhowꢀtoꢀuseꢀtheꢀeX‐10.ꢀ
ꢀꢀSelectingꢀbetweenꢀcarꢀradioꢀandꢀeX‐10ꢀmodeꢀ(Note:ꢀꢀnotꢀapplicableꢀwhenꢀusingꢀ
“Optionꢀ#1”ꢀ(AUXꢀinput).)ꢀ
Useꢀtheꢀꢀbuttonꢀtoꢀexitꢀtheꢀ“setup”ꢀmenu.ꢀꢀꢀ
WhenꢀplayingꢀaꢀsourceꢀonꢀtheꢀeX‐10ꢀusingꢀtheꢀ
KWE‐155BꢀFMꢀantennaꢀsplitter,ꢀyouꢀmustꢀ
switchꢀtheꢀantennaꢀsplitterꢀtoꢀeX‐10ꢀmode.ꢀꢀ
Thisꢀcanꢀbeꢀdoneꢀbyꢀpressingꢀtheꢀ“Func.”ꢀ
buttonꢀforꢀtwoꢀseconds.ꢀꢀ“eX‐10”ꢀwillꢀshowꢀinꢀ
theꢀbottomꢀleftꢀcornerꢀofꢀtheꢀscreen.ꢀ
Whenꢀyouꢀwantꢀtoꢀlistenꢀtoꢀtheꢀcar’sꢀFMꢀradio,ꢀsimplyꢀ
pressꢀandꢀholdꢀ“func.”ꢀforꢀtwoꢀsecondsꢀtoꢀswitchꢀꢀ
theꢀantennaꢀsplitterꢀtoꢀ“carꢀantenna”ꢀmode.ꢀꢀꢀ
“CarꢀAntenna”ꢀwillꢀshowꢀonꢀtheꢀbottomꢀleftꢀcornerꢀ
ofꢀtheꢀscreen.ꢀ
Page 13
UsingꢀtheꢀeX‐10ꢀ
Here’sꢀtheꢀbasicsꢀonꢀhowꢀtoꢀuseꢀtheꢀeX‐10.ꢀ
ꢀꢀPlayingꢀsongsꢀfromꢀtheꢀiPodꢀ
Pressꢀ“source”ꢀtoꢀselectꢀ“iPod”.ꢀꢀ
Pressꢀtheꢀ“enter”ꢀbutton,ꢀthenꢀuseꢀtheꢀ>>Iꢀandꢀ
I<<ꢀbuttonsꢀtoꢀsearchꢀbyꢀartist,ꢀalbum,ꢀsong,ꢀ
etc.ꢀꢀTapꢀ“enter”ꢀtoꢀchooseꢀanyꢀsearchꢀmethod,ꢀ
usingꢀtheꢀ>>IꢀandꢀI<<ꢀbuttonsꢀtoꢀselectꢀaꢀsong.ꢀꢀꢀ
Pressingꢀ“enter”ꢀwillꢀbeginꢀsongꢀplayback.ꢀꢀꢀꢀ
Withꢀtheꢀsongꢀplaying,ꢀyouꢀshouldꢀnowꢀseeꢀtheꢀ
iPod’sꢀalbumꢀartꢀdisplayedꢀonꢀtheꢀeX‐10ꢀscreen.*ꢀꢀ
Pressꢀtheꢀ“view”ꢀbuttonꢀtoꢀscrollꢀbetweenꢀtheꢀ
threeꢀdifferentꢀdisplayꢀmodes.ꢀ
Youꢀcanꢀalsoꢀchooseꢀtheꢀdisplayꢀbackgroundꢀthatꢀ
bestꢀmatchesꢀyourꢀdashꢀbyꢀselectingꢀ“display”ꢀinꢀ
theꢀ“setup”ꢀmenu,ꢀthenꢀ“BGVꢀselect”.ꢀꢀ
Page 14
*Note:ꢀꢀAlbumꢀArtꢀmustꢀbeꢀstoredꢀonꢀyourꢀiPodꢀinꢀorderꢀtoꢀbeꢀdisplayedꢀonꢀtheꢀeX‐10ꢀ
UsingꢀtheꢀeX‐10ꢀ
Here’sꢀtheꢀbasicsꢀonꢀhowꢀtoꢀuseꢀtheꢀeX‐10.ꢀ
Makingꢀandꢀreceivingꢀphoneꢀcallsꢀꢀ
Pressꢀtheꢀꢀꢀꢀbutton,ꢀandꢀuseꢀtheꢀ>>IꢀandꢀI<<ꢀ
buttonsꢀtoꢀselectꢀ“Phonebook”.ꢀꢀPressꢀ“enter”,ꢀthenꢀ
useꢀtheꢀ>>IꢀandꢀI<<ꢀbuttonsꢀtoꢀfindꢀtheꢀdesiredꢀ
contactꢀinꢀtheꢀphoneꢀbook.ꢀꢀPressꢀꢀ
againꢀtoꢀdialꢀtheꢀnumber.ꢀꢀYouꢀmayꢀalsoꢀselectꢀ
numbersꢀfromꢀtheꢀdialed,ꢀreceived,ꢀorꢀmissedꢀcallsꢀ
listsꢀusingꢀthisꢀmethod.ꢀ*ꢀꢀꢀ
Youꢀwillꢀnowꢀhearꢀtheꢀphoneꢀdialingꢀthroughꢀyourꢀ
car’sꢀstereoꢀsystem.ꢀꢀToꢀhangꢀup,ꢀpressꢀꢀ
Whenꢀaꢀcallꢀcomesꢀin,ꢀsimplyꢀpressꢀꢀꢀꢀtoꢀ
answerꢀit.ꢀ
Toꢀhangꢀup,ꢀpressꢀꢀ
Youꢀcanꢀalsoꢀselectꢀꢀ“AutoꢀAnswer”ꢀunderꢀ
“Bluetooth”ꢀinꢀtheꢀ“setup”ꢀmenuꢀifꢀyouꢀwantꢀtheꢀ
eX‐10ꢀtoꢀautomaticallyꢀanswerꢀanyꢀcallꢀthatꢀ
comesꢀin.ꢀꢀ
Page 15
*Note:ꢀꢀAllꢀfeaturesꢀareꢀnotꢀenabledꢀonꢀallꢀphones.ꢀꢀCheckꢀwithꢀyourꢀphoneꢀserviceꢀprovider.ꢀ
UsingꢀtheꢀeX‐10ꢀ
Here’sꢀtheꢀbasicsꢀonꢀhowꢀtoꢀuseꢀtheꢀeX‐10.ꢀ
Listeningꢀtoꢀsongsꢀstoredꢀonꢀtheꢀphoneꢀ
IfꢀtheꢀphoneꢀisꢀBluetoothꢀaudioꢀenabled,ꢀyouꢀ
canꢀplayꢀsongsꢀfromꢀyourꢀphoneꢀthroughꢀtheꢀ
eX‐10.ꢀꢀPressꢀ“source”ꢀtoꢀselectꢀ“Bluetoothꢀ
Audio”ꢀmode,ꢀthenꢀuseꢀ>>I,ꢀI<<,ꢀandꢀ>/IIꢀtoꢀ
controlꢀtheꢀaudioꢀtracks.ꢀ
Apple, the Apple logo, iPod and iTunes are registered trademarks of Apple, Inc. The Bluetooth logo is owned by the Bluetooth
SIG, Inc. Product information listed in this guide is based upon current information at the time of printing, but cannot be
guaranteed. All designs, features, and specifications are subject to change without notice. For updated product information,
Page 16
|
Nokia 239 User Manual
NETGEAR ReadyNAS 600B User Manual
Motorola GSM V300 User Manual
Kenwood DP R797 User Manual
Fujitsu MHT2080AT User Manual
Classe Audio CDP 100 User Manual
Cary Audio Design CD 306 User Manual
Antec SOLUTION SERIES SLK1650B User Manual
Addonics Technologies ZSNA256EU User Manual
603 Nokia User Manual