Vita Mix XL VM0141 User Manual

®
Vita-Mix Corporation  
Use and Care Manual  
Read and Save These Instructions  
TM  
XL VARIABLE SPEED  
LARGE CAPACITY BLENDER  
Model: VM0141  
Important Safeguards  
16. When making nut butters or oil based foods, do not process for more than one  
minute after mixture starts circulating. Overprocessing can cause dangerous  
overheating as well as damage the container.  
17. Always operate the Vita-Mix machine with a lid in place.  
18. WARNING: When processing hot liquids:  
• The two-part latching lid must be securely in place. This allows steam to escape  
naturally and will prevent the lid from coming off when the machine is turned on.  
• Do not start on HIGH speed or the highest speed setting. Always start hot liquids  
on LOW speed or the lowest setting, then increase speed as the machine is running.  
• Use caution with hot liquids. Spraying from under the lid plug can occur, or  
escaping steam may cause scalding.  
WARNING: When pouring hot liquids and mixtures:  
• Be sure the container has the protective sure-grip hand guard.  
• Wear long sleeves and gloves for protection.  
19. CAUTION: Turn power OFF or unplug the machine before touching movable parts.  
Shut OFF power switch at night or whenever machine will be left unattended.  
Save These Safety Instructions  
The Vita-Mix blender’s U.S. power cord comes equipped with a three-prong  
(grounding) plug which mates with a standard three-prong wall outlet (Figure A). This  
cord will vary for countries outside the United States.  
Adapters (Figure B) are available for two-prong outlets. Do not cut or remove the  
third (ground) prong from the plug or power cord.  
Consult your electrician if you are not sure if the wall outlet is grounded through the  
building wiring. With a properly grounded two-prong wall outlet, ground the machine by  
attaching the tab on the adapter to the wall outlet cover by means of the screw in the  
center of the cover (Figure B).  
WARNINGS!  
THREE-PRONG ADAPTERS ARE NOT TO BE USED IN CANADA.  
Figure B  
Figure A  
IMPORTANT NOTES!  
The instructions appearing in this Use and Care Manual cannot cover every possible condition and  
situation that may occur. Common sense and caution must be practiced when operating and  
maintaining any appliance.  
3
CONTROL PANEL  
Start/Stop Switch  
Pulse Switch  
Variable Speed Dial  
ON  
OFF  
VARIABLE SPEED  
LARGE CAPACITY BLENDER  
XLTM – Variable Speed  
ON/OFF Switch. Located on the side of the machine, the ON/OFF  
switch controls the power to the machine.While plugged in, switch  
to ON to ready the machine for blending. Shut OFF the power  
switch at night or whenever the machine will be left unattended.  
START/STOP Switch – The START/STOP switch is located on the  
left side of the control panel when facing the machine.Activate the  
machine by depressing the top of the switch button to start ( ),  
and stop the machine by depressing the bottom of the switch to stop ( ). The START/STOP  
switch will activate the blades at the selected variable speed dial setting.  
VARIABLE SPEED DIAL – Allows the user to select continuously variable motor speeds  
ranging from 1,500 rpm to 28,000 rpm.  
PULSE Switch – Pulse switch can only be used when the START/STOP switch is in the  
stopped or the ( ) position. The pulse switch can be used to quickly refresh product in the  
container by depressing the switch and holding down as long as needed. When activated,  
the pulse switch operates the machine at the selected variable speed dial setting.  
IMPORTANT NOTES!  
Cleaning: Switches may become sticky from use. Unplug the machine and use a wet cloth,  
moistened with water and a mild detergent, to clean around the edges of the switch paddles until  
they function freely. Work the switches back and forth a few times to loosen any dried residue under  
switch. Leaving switches sticky will damage or burn out the switches. Clean carefully, using caution  
not to allow water or other liquids to infiltrate the switch.  
WARNING: When the machine is not in use, turn the ON/OFF Switch to OFF, or unplug the machine  
from the outlet.  
4
BLENDING TIPS  
1. If your ingredients freeze up, try reducing the amount of ice. Compared to other blenders,  
TM  
you do not need as much ice to make an equally frozen drink in an XL Blender.  
2. Place liquids and soft foods in your container first. Hard items and ice should be placed last.  
3. Whole, hard or frozen ingredients should be small. Solid frozen fruit is extremely difficult to  
blend. For best results, use semi-frozen fruit. Using same-size batches of semi-frozen fruit  
and ice will keep your drinks consistent. If you notice chunks, reevaluate the batch size.  
4. When creating recipes, always allow for enough liquid to ease the blending process. For  
recipes with minimal liquid, use the VARIABLE  
SPEED DIAL to run the machine on its lowest  
setting until it is processing smoothly.  
5. When using the Extra Large Capacity container,  
both hands should be used when pouring. Slide  
one hand under the spout and use the other  
hand to hold the handle (Figure A).  
6. When blending hot product be sure to use the  
container with the protective sure-grip hand  
guard (Figure A). Gloves and long sleeves should  
be worn when pouring.  
FIGURE A  
IMPORTANT NOTES!  
• Check your blades daily. If you find something is loose, nicked or missing, replace the blade  
assembly before use (see page 19). Do not tighten hex-headed screw (on top of blade assembly).  
If loose, replace blade assembly.  
• The instructions appearing in this Use and Care Manual cannot cover every possible condition and  
situation that may occur. Common sense and caution must be practiced when operating and  
maintaining any appliance.  
5
LID ASSEMBLY  
To secure lid plug, rotate it so one tab locks  
between the notches on top of rubber lid  
Two-Piece Accelerator  
Tool Lid  
64 oz. / 2.0 L Advance Container  
• To secure lid, place on top of container and  
gently press down until lid snaps into place,  
making sure the latches are secured around  
the top of the container rim.  
Lift lid tabs  
to remove lid  
• To remove a fully latched lid, lift one of the  
two tabs and pull upward and off.  
• Twist the center lid plug to fasten or remove.  
• The lid plug can be removed when using the  
accelerator tool or adding ingredients.  
FIGURE B  
To secure lid plug, rotate it so one tab locks  
between the notches on top of rubber lid  
Two-Piece Lid (optional)  
64 oz. / 2.0 L Advance Container  
The two-piece lid is easy to clean and easy to put on,  
take off and seal.  
Lift lid tabs  
to remove lid  
• To secure lid, place on top of container and  
gently press down until lid snaps into place,  
making sure the latches are secured around  
the top of the container rim.  
• To remove a fully latched lid, lift one of the  
two tabs and pull upward and off.  
• Twist the center lid plug to fasten or remove.  
DO NOT USE WITH ACCELERATOR TOOL  
FIGURE A  
IMPORTANT NOTES!  
Containers:  
• XLTM Blenders are optimized for use with the Vita-Mix 1.5 gal. / 5.7 L & Advance 64 oz. / 2.0 L containers.  
Use of other Vita-Mix standard containers (64 oz. / 2.0 L, 48 oz. / 1.5 L, or compact 32 oz. / 0.9 L)  
are not compatible. Call Vita-Mix Customer Service or your distributor for more information.  
Lids:  
To make new lids easier to insert and remove, rub a light coating of cooking oil around the rim  
where it seals. Place it in a container for several minutes, remove and lightly wipe oil off lid.  
6
Two-Piece Lid  
1.5 gal. / 5.7 L Extra Large Container  
The two-piece lid is easy to clean, easy to put on,  
take off and seal.  
To secure lid plug, rotate it so one tab locks  
between the notches on top of rubber lid  
Lift lid tabs  
to remove lid  
• To secure lid, place on top of container and  
gently press down until lid snaps into place,  
making sure the latches are secured around  
the top of the container rim.  
• To remove a fully latched lid, lift one of the  
two tabs and pull upward and off (Figure D).  
• Twist the center lid plug to fasten or remove.  
• The lid plug can be removed when using the  
accelerator tool or adding ingredients.  
FIGURE C  
FIGURE D  
7
GENERAL INSTRUCTIONS  
WARNINGS!  
• When the machine is not in use, unplug the machine from the outlet.  
• If you detect a change in the sound of the machine or if a hard or foreign object comes into contact  
with the blades, do not serve the contents. Inspect your blade assembly for loose, nicked or missing  
parts. If parts are loose, missing, or nicked, replace with new blade assembly. (See page 19.)  
When processing hot liquids always:  
• Use caution; escaping steam or splashes may scald  
• Lock the lid. This will prevent the lid from blowing off when the machine is activated.  
• Start on VARIABLE SPEED #1 and quickly increase to #10. Never start on the highest speed when  
blending hot ingredients.  
XLTM Blender Instructions  
1. Place liquids and soft foods in the container first. Placing wet ingredients towards the blades  
helps to start the vortex that allows the other ingredients to be pulled into the blades.  
Although not necessary for processing, cutting or breaking food into smaller pieces (1 to 3 in.  
/ 3 to 8 cm) allows for more precise measuring of ingredients.Thawed or partially-thawed fruit  
is recommended. The highest speed is recommended for heavy-duty blending.  
2. Set the container on the motor base by aligning it over the centering pad anchored to  
the base. (Motor must be completely stopped before positioning container.)  
Containers are not to be used for hard, dry materials. Avoid running your machine with the  
container empty.  
3. Always use a lid when blending. If blending hot ingredients, the lid must be securely latched  
in place. When processing hot liquids, DO NOT use a non-latching or one-piece lid.  
4. To achieve the best blend, always make sure you fill the 1.5 gal. / 5.7 L container to the  
48 oz. / 1.4 L level or higher with ingredients. If finished volume is less than 48 oz. / 1.4 L,  
use the Advanced container.  
5. Plug the machine into the nearest outlet (if unplugged).  
6. Select the desired speed. It is recommended to start on variable speed #1 and slowly work  
the variable speed dial to attain the desired blend consistency.  
6a. To prevent possible splashing, lightly rest your hand on the lid while turning the  
machine on (except when processing hot liquids or mixtures).  
6b. Until you become accustomed to the speed, watch your mixture carefully to avoid over-  
blending.  
6c. The lower the speed, the coarser the blend. The higher the speed, the finer the blend.  
In order to avoid over processing, always start at the lowest variable speed and work  
your way up.  
6d. If during blending, the mixture seems too thick, remove the lid plug and slowly add  
liquid through the lid opening while processing.  
8
7. Set the ON/OFF switch to ON.  
8. When blending hard to blend mixtures such as dips and spreads, or mixtures using frozen  
ingredients, use the accelerator tool (see page 11) to help ingredients flow into the blades.  
Continuously moving the tool around in a circular motion during blending will help eliminate  
air pockets and encourage an even blend.  
9. After the blender has been stopped, wait until the blade comes to a complete stop before  
removing the lid or container from the motor base.  
10. To use the PULSE switch: Turn the dial to the desired variable speed.With the container on  
the motor base, depress the pulse switch. Release the switch to stop the motor. Repeat multiple  
times until mixture is blended to desired consistency.  
11. Unplug the machine when not in use.  
Maintenance Tips:  
Never bang the container against a surface to loosen the ingredients. Remove the  
container from the base and use a rubber spatula to remove thick mixtures from the  
bottom of your container.  
Never shake or rattle a container while in use.  
• Never remove the container before the machine has come to a complete stop.  
• Never start the motor before the container is in place.  
IMPORTANT NOTES!  
• The automatic overload protection shuts the motor off when the resettable circuit breaker pops  
out. It does so to protect the motor from overheating. If the motor shuts off, it could be due to:  
– Recipe being too thick  
– Recipe having too many ingredients in it  
– Recipe was being processed too long at too low a speed  
• The machine may stop working if it is overloaded on low speed. Reset the machine by turning  
power off for 30 seconds.  
THERMAL PROTECTOR: The thermal protector may shut the motor off to protect it from  
overheating. To restart, wait for motor to cool down with the power off (up to 45 minutes). Cooling  
may be quickened by placing the motor base in a cool spot. (Unplug first.) To speed up the process,  
try circulating the air with a vacuum or fan aimed at the bottom of the base. When the thermal  
protector shuts the motor off, review your processing techniques and your instructions. Your recipes  
may be too thick or have too much material in them. If the motor seems to be overheating but the  
thermal overload protector has not turned the machine off, stop the machine and remove the  
container from the base. Turn the machine ON and let the machine run for 20 seconds. Repeat this  
step 3 times for a total of 1 minute. Be careful never to touch any moving parts while in use.  
9
WARNINGS!  
Never use a blade assembly with loose, damaged, nicked, or missing components.  
Caution: Do not remove blades or blade assembly unless absolutely necessary! Never attempt to  
take the blade assembly itself apart. This will void the warranty.  
Blade Agitator Assembly. The blade assembly includes  
a precision-hardened stainless steel blade with enclosed  
steel ball bearings for maximum durability. The rugged  
blade assembly literally explodes molecules of food and  
ice in the container, helping every batch to homogenize  
more effectively. The blade does not need to be removed  
3
for normal cleaning. (Refer to the information below to  
remove or replace.)  
Drive Spline. Mates with drive socket on the motor base  
to turn the blade. Note: Removing and replacing your  
container while the coupling is still rotating will strip the  
drive spline “teeth. (This part is NOT removable.)  
Retainer Nut. Must be snug. Order the available  
Retainer Nut Wrench for best results. (Refer to the  
information below to remove or replace.)  
Removing Blade Assembly  
At times, it may be necessary to give your blades additional  
cleaning. An easy-to-use blade assembly removal wrench (Item  
#15596) may be purchased through your Vita-Mix Distributor.  
Turn the container upside down and grip firmly. Insert retainer  
RETAINER NUT WRENCH  
nut wrench in groove of retainer nut and rotate counterclockwise  
to loosen. Then grip blades with a cloth and remove retainer nut  
by hand.  
Replacing Blade Assembly  
With the container upside down, grip blades with cloth, insert  
into the container bottom and align with flat sides of container  
opening. Place retainer nut on and hand tighten. Last, carefully  
turn clockwise until secure, using wrench. Do not force. If it is  
Retainer Nut Wrench in use.  
not tight enough, you will notice increased container noise.  
10  
WARNINGS!  
When processing hot liquids or mixtures:  
• The two-part latching lid must be securely locked in place. DO NOT use the one piece lid or a non-  
latching lid. This allows steam to escape naturally and will prevent the lid from coming off when  
the machine is turned on.  
• Do not start processing hot liquids on HIGH speed. Always start processing hot liquids on LOW  
speed, then switch to HIGH speed while the machine is running.  
• Use caution with hot liquids. Liquids may spray from under the lid plug or escaping steam may  
cause scalding.  
DO NOT force the accelerator tool into the container. Excessive force may cause the accelerator tool  
to extend too far into the container and may cause damage to the blades.  
DO NOT use the older accelerator tool that has a straight and smooth surface and no “step.” Use of  
the older model may cause damage to the blades.  
The accelerator tool prevents an air bubble  
from forming while blending and allows for  
the processing of very thick and/or difficult-to-  
Splash Disk  
process frozen mixtures. While the machine is  
running, use the accelerator tool to push  
ingredients into the blades.  
Using the Accelerator Tool:  
• If thick mixtures stop circulating, you may  
have trapped an air bubble. Insert the  
accelerator tool through the lid and stir to  
release it.  
• Use it only with the lid locked in place and  
lid plug removed.  
• The splash disk (near the top of the accelerator tool) and lid prevent the accelerator tool  
from hitting the blades.  
• The container should not be more than 2/3 full when the accelerator tool is used.  
• Do not use the accelerator tool for more than 30 consecutive seconds (to avoid  
overheating).  
• Holding the accelerator tool straight should allow extra-thick ingredients to circulate. If  
not, point the accelerator tool toward the side or corner of the container.  
11  
Care Note  
To ensure that you get the longest possible life from your Vita-Mix® machine, we recommend  
the following products, when used as directed by the supplier:  
CLEANING PRODUCTS . . . . . . . . . . . . . . . . . . . . . . . . . . SUPPLIERS IN USA  
Solid Supra, Solid Power, . . . . . . . . . . . . . . . . . . . . . . . . . Ecolab, Inc., St. Paul, MN  
Guardian Acclaim, Solid Guardian Plus, . . . . . . . . . . . . . . 800-352-5326  
Solid Super Impact, Solid Insure . . . . . . . . . . . . . . . . . . . . . www.ecolab.com  
Diverpak . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diversey, Livonia, MI  
Eclipse H2, Liqui-Safe L7 . . . . . . . . . . . . . . . . . . . . . . . . . 800-521-8140  
Acclean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Klenzade Products  
Poly-Brite. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Division of Ecolab  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . St. Paul, MN; 612-293-2165  
Glow MB-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wesmar Company, Inc.  
Lustre NC-25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seattle, WA  
Lustre Plus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206-783-5344; www.wesmar.com  
PSRA 41-D, PSRA 41-E, . . . . . . . . . . . . . . . . . . . . . . . . . . Anderson Chemical Co.  
Liqui-Ware 1, Liqui-Ware MC. . . . . . . . . . . . . . . . . . . . . . Litchfield, MN  
D-Flex, Sur-Met . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800-366-2477  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . www.andersonchemical.com  
RINSE AIDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SUPPLIERS IN USA  
Solid Rinse Dry, Solid Brilliance, . . . . . . . . . . . . . . . . . . . . Ecolab, Inc., St. Paul, MN  
Jet Dry, Rinse Dry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800-352-5326; www.ecolab.com  
DESTAINER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SUPPLIERS IN USA  
NuWare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diversey, Livonia, MI  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800-521-8140  
IMPORTANT NOTES!  
CLEANING PRODUCTS: Do not use abrasive cleaning agents or concentrated bleach when  
cleaning. Use the cleaning products and rinse aids specifically recommended by Vita-Mix.  
CLEANING: Switches may become sticky from use. Unplug the machine and use a wet cloth,  
moistened with water and a mild detergent, to clean around the edges of the switch paddles until  
they function freely. Work the switches back and forth a few times to loosen any dried residue under  
switch. Leaving switches sticky will damage or burn out the switches. Clean carefully, using caution  
not to allow water or other liquids to infiltrate the switch. Dry with a soft cotton cloth.  
CONTAINER: Do not let mixtures, liquids and food products dry in the container. Rinse throughout  
use. Dry product may lock around the blade and weaken/tear the bearings seal when restarted. Do  
not place containers in the freezer. Extremely low temperature combined with hot ingredients and/or  
the immediate rapid action of the blade may crack the container. Follow the cleaning instructions on  
page 13.  
12  
Motor Base/Control Panel  
1. Unplug the power cord.  
2. Gently wash the outside surface with a damp soft cotton cloth moistened with a mild  
solution of warm water and nonabrasive detergent or nonabrasive liquid spray cleaner.  
NEVER IMMERSE MOTOR BASE IN WATER OR OTHER LIQUID.  
3. Thoroughly clean switches so that they work freely. They may become sticky from use.  
Unplug the machine and use a wet cloth, moistened with water* and a mild detergent, to  
clean around the edges of the switch paddles until they function freely. Work the switches  
back and forth a few times to loosen any dried residue under switch. Leaving switches  
sticky will damage or burn out the switches. Clean carefully, using caution not to allow  
water or other liquids to infiltrate the switch.  
4. Dry with a soft cotton cloth.  
Lid  
Separate the lid and plug. Wash in warm soapy water. Rinse clean under running water and  
dry. Reassemble before use. (See page 6.)  
Container  
1. To Clean: Fill container 1/4 full with warm (110˚F/43˚C) water and add a couple drops of  
liquid dishwashing detergent.** Return container to motor base and firmly position the  
two-piece lid. Run machine for 30 seconds. Empty container. Repeat this step.  
2. To Rinse: Fill container 3/4 full with warm (110˚F/43˚C) water – do not add soap. Return  
container to motor base and firmly position the two-piece lid. Run machine for 30  
seconds. Empty container.  
3. If any solid residue remains, remove the blade assembly (see page 8) and wash all  
container parts in warm soapy water. Rinse and drain. Reassemble before next step. Do  
not soak the blade assembly.  
4. To Sanitize: If all solid residue is gone after step 2 or after completion of step 3,  
fill container 3/4 full with a sanitizing solution mix.*** Return container to motor base and  
firmly position the two-piece lid. Run machine on a high speed for 30 seconds.Turn machine  
off and allow mixture to stand in the container for an additional 1-1/2 minutes. Pour out  
sanitizing solution mixture.  
5. Return container to motor base and run machine empty for an additional 5 seconds. Do  
not rinse after sanitizing. Allow container to air dry.  
IMPORTANT NOTES!  
* Be sure to wring excess water out of cloth or sponge when cleaning around the controls or any  
electrical part.  
** To prolong container life, Vita-Mix recommends using soaps with a low Ph balance, such as a liquid  
dishwashing detergent (Ivory Liquid®).  
*** Recommended sanitizing solution: 1.5 tsp. / 7.4 ml institutional or household bleach in  
2 qt. / 2.0 Ltr. water.  
13  
XLTM Blender  
Item #  
#15900  
#15899  
#15896  
#15897  
#15901  
#15892  
#15894  
Part  
Lid and plug for 1.5 gal. / 5.7 L Large Capacity Container  
1.5 gal. / 5.7 L Large Capacity Container, blade assembly & lid assembly  
1.5 gal. / 5.7 L Large Capacity Container only  
XL blade agitator assembly for Large Capacity Container  
XP retainer nut for Large Capacity Container  
Accelerator Tool Lid and plug for 64 oz. / 2.0 L Advance Container  
64 oz. / 2.0 L Advance Container, blade assembly & Accelerator Tool Lid  
assembly  
#15893  
#15941  
#15942  
#15902  
#15895  
#755  
64 oz. / 2.0 L Large Capacity Container only  
XL Blade agitator assembly for Advance Container  
XP retainer nut for Advance Container  
Drive socket  
XL Centering Pad  
Lid Plug for Large Capacity Container and Advance Container  
Accelerator Tool  
#760  
IMPORTANT NOTES!  
Outside the United States and Canada, your machine may come with a different container  
configuration. Contact your local Vita-Mix® Distributor for item numbers.  
Other than the drive socket, blade assembly and retainer nut, this machine is only serviceable and  
repairable by an authorized Vita-Mix service provider. Do not attempt to service or repair your  
machine on your own.  
14  
Items Sold Separately:  
#755  
#15900  
#XXXXX  
#15899  
#15596  
Retainer Nut Wrench  
#15896  
#15897  
#XXXXX  
#15901  
#15902  
#15895  
#755  
#15892  
#XXXXX  
#760  
#15894  
#15893  
#XXXXX  
#15941  
#15942  
15  
Solution #1:  
1. Problem:  
Check blade assembly for loose, damaged or  
nicked components and replace.  
Solution #2:  
Tighten retainer nut with retainer nut wrench  
moving clockwise until it is snug. See page 10.  
• Increased vibration  
• Leaking from bottom of container  
• Increased container noise  
Solution #1:  
2. Problem:  
Double-check to make sure power cord is  
firmly in power outlet.  
• Machine will not run  
Solution #2:  
Check to make sure the ON/OFF Switch is in  
the ON position. Check to make sure  
switches are clean and moving freely.  
Solution #3:  
The thermal protector may have shut the  
machine off. Turn power off for up to 45  
minutes to reset. Note: Cooling may be  
quickened by placing the motor base in a  
cool spot. (Unplug first.) Try circulating the air  
with a vacuum or fan aimed at the bottom of  
the motor base.  
3. Problem:  
Solution #1:  
• Loud noise from blade area  
• Blades don’t spin  
Drive socket may be broken. Check for a  
fine crack down the center or worn teeth -  
replace with a new drive socket (Item  
#891). Instructions are included with part.  
Solution #2:  
Blade bearings need to be replaced. Spin  
the blades using the drive spindle at the  
bottom of the container. If blades spin freely  
with no resistance, replace blade assembly.  
See page 10.  
Solution #3:  
Drive spindle on the blade assembly may be  
worn. Check for worn teeth on the drive  
spindle of the blade assembly. Replace  
blade assembly. See page 10.  
16  
4. Problem:  
Solution:  
Motor bearings need to be replaced. Call  
• Loud grinding noise from the blender  
motor  
Vita-Mix® Customer Service.  
5. Problem:  
Solution #1:  
Try plugging the machine into a new outlet.  
• Machine is running irregularly  
• Machine starts by itself  
• Machine was turned off for a period  
of time and turned on, but there is  
no power  
Solution #2:  
Call Vita-Mix Customer Service.  
• Machine did not work right out of  
the box  
Cooling the Motor:  
Machine may stop working if it is overloaded on low speed. Reset by turning power off for  
up to 30 seconds.  
If you cannot fix your machine with these suggestions, technical help is available by  
calling Vita-Mix Technical Support, 800-886-5235. If outside the United States and Canada,  
contact your local Vita-Mix Distributor or telephone the Vita-Mix International Division at  
+1.440.782.2450 or email [email protected] for a distributor in your country.  
IMPORTANT NOTES!  
• The automatic overload protection shuts the motor off when the resettable circuit breaker pops  
out. It does so to protect the motor from overheating. If the motor shuts off, it could be do to:  
– Recipe being too thick  
– Recipe having too many ingredients in it.  
– Recipe was being processed too long at too low a speed  
THERMAL PROTECTOR: The thermal protector may shut the motor off to protect it from  
overheating. To restart, wait for motor to cool down with the power off (up to 45 minutes). Cooling  
may be quickened by placing the motor base in a cool spot. (Unplug first.) To speed up the process,  
try circulating the air with a vacuum or fan aimed at the bottom of the base. When the thermal  
protector shuts the motor off, review your processing techniques and your instructions. Your recipes  
may be too thick or have too much material in them. If the motor seems to be overheating but the  
thermal overload protector has not turned the machine off, stop the machine and remove the  
container from the base. Turn the machine ON and let the machine run for 20 seconds. Repeat this  
step 3 times for a total of 1 minute. Be careful never to touch any moving parts while in use.  
17  
LIMITED WARRANTY  
In order to maximize the life and keep your Vita-Mix® product in good working order, it is  
important that you follow a few simple maintenance instructions:  
1. Periodically inspect the drive socket and replace with the extra drive socket that is  
enclosed with your purchase. Additional replacement parts are available as needed by  
calling our Technical Service Department at 800-886-5235.  
2. Manually rotate the blade bearing assembly to make sure it turns without hesitation.  
3. Never run the machine without the centering pad properly placed on the base.  
Vita-Mix Corporation (hereinafter “Vita-Mix”) warrants to the original end-user (proof of  
purchase required) that this commercial Vita-Mix blender (hereinafter the “Equipment”) is  
free from defects in material and workmanship for the warranty periods applicable to the  
Equipment as described herein and subject to the conditions set forth below.  
Motor Base  
Vita-Mix warrants that:  
• if the motor base fails within thirty (30) days from the date of purchase, Vita Mix will  
replace the motor base without charge.  
• if the motor base fails after thirty (30) days but within one year from the date of purchase,  
due to a defect in materials or workmanship,Vita-Mix will assume the cost of all parts and  
labor necessary to repair the motor base.  
• if the motor base fails after one year but within three (3) years from the date of purchase  
due to a defect in materials or workmanship, Vita-Mix will assume the cost of the parts  
deemed necessary to repair the base.  
Container, Lid, Blade Assembly, Drive Socket  
and Sound Enclosure (if included)  
The container, lid, blade assembly, drive socket and where included a Vita-Mix manufactured  
sound enclosure, are warranted against defects in material and workmanship for one year  
from the date of purchase.  
Conditions  
• The warranties contained herein run only to the original end-user and are not transferable.  
To make a warranty claim, proof of purchase may be required.  
• The warranties contained herein do not cover normal wear-and-tear, abuse, misuse,  
negligent use, alteration of the base or container (or the sound enclosure), or exposure to  
extreme conditions. The warranties are only valid if the Equipment is used in accordance  
with this owners manual (which may also be accessed at www.vitamix.com/foodservice).  
• Improper installation or ventilation in the case of the in-counter model of the Equipment,  
or placing the Equipment in a sound enclosure not manufactured by Vita-Mix will void the  
warranty.  
18  
• The warranty is void in the event that repairs to the Equipment are performed by  
®
someone other than Vita-Mix, or an authorized Vita-Mix Service Center. Vita-Mix will not  
be responsible for the cost of any unauthorized repairs.  
• The sole obligation of Vita-Mix under the warranties herein is to repair or replace the  
warranted part or parts as determined exclusively by Vita-Mix.  
In no event, whether based on contract, indemnity, warranty, tort (including  
negligence), strict liability or otherwise, shall Vita-Mix be liable for any special,  
indirect, incidental or consequential damages whatsoever including, without  
limitation, loss of profit or revenue. The above limited warranty is the exclusive  
remedy, and Vita-Mix hereby expressly disclaims all other warranties, express or  
implied, including the implied warranty of merchantability and the implied  
warranty of fitness for a particular purpose, and, without limiting the generality of  
the foregoing, the original end-user and Vita-Mix hereby expressly exclude, to the  
extent permitted by law, the application of any sale of goods legislation and the  
United Nations Convention on Contracts for the International Sale of Goods, as  
may be applicable.  
The foregoing constitutes the original end-user’s sole remedy and the sole liability of Vita-Mix.  
No employee of Vita-Mix or any other person is authorized to make any warranty in addition  
to or amendment of the warranties made herein.  
In the event your Vita-Mix blender needs service or repair covered by the terms of this  
warranty, please call the Vita-Mix Corporation for shipping instructions. For machines sold  
in the United States, call Vita-Mix Technical Support: 800-886-5235. If you live outside the  
United States, Canada or Latin America contact your local Vita-Mix Distributor, or telephone  
the Vita-Mix International Division at +1.440.782.2450 or email [email protected]  
for a distributor in your country.  
Any item sent to Vita-Mix pursuant to the terms hereof must be sent in original or sufficient  
packaging. Customer is responsible for in-bound freight costs for warranty service. Do not  
return or send in products without the approval from Vita-Mix. All product returns must  
have the Return Authorization number clearly marked on the outside of the box. Any  
product that is sent to Vita-Mix without prior authorization or approval will be returned to  
the shipper’s address “as is” without repair.  
19  
Dimensions:  
17.63 in. /  
44.77 cm  
with 64 oz.  
/ 2.0 L  
advance  
container  
18.25 in. /  
45.6 cm  
with  
12.5 in. /  
31.75 cm  
1.5 gal. /  
5.7 L  
container  
19 in./  
83 in. /  
8.5 in. /  
19 cm  
8.5 in. /  
19 cm  
48.26 cm  
195.58 cm  
Overall motor base dimensions:  
With 1.5 gal. / 5.7 L Container:  
12.5 in. / 31.75 cm High x 8.5 in. / 21.59 cm  
Wide x 19 in. / 48.26 cm Deep  
18.25 in. / 45.6 cm High  
With 64 oz. / 2.0 L Advance Container: 17.63 in. / 44.77 cm High  
Ship weight of machine: 50 lbs. / 22.7 kg  
Power Requirements:  
Volts: 120 VAC  
Amps: 15  
Hz: 50/60  
When applicable:  
NSF  
®
To see the complete line of Vita-Mix products,  
VITA-MIX® CORPORATION  
Foodservice Division  
8615 Usher Road, Cleveland, Ohio 44138-2103 USA  
©2008 Vita-Mix Corporation. No part of this publication may be reproduced or transmitted in any form or  
by any means or stored in a database or retrieval system without the written permission of the Vita-Mix Corporation.  
Printed in U.S.A.  
015943 11/08  

Tokina MONOFOCAL LENS TC0614AI User Manual
Speco Technologies DVR 16TT User Manual
Sony XR 3100R User Manual
Sony Xplod CDX F7715X User Manual
Sony HVR Z5N User Manual
Sony DSCH70B User Manual
Sony Car Stereo System TC WE475 User Manual
Sirius Satellite Radio KCA R70FM User Manual
SanDisk 80 11 00943 User Manual
Samsung SR L39 User Manual