Vista Imaging VFSM15 User Manual

Vista 15” TFT LCD MONITOR  
USER  
MANUAL  
MODEL: VFSM15  
FCC INFORMATION  
This equipment has been tested and found to comply with the limits for a  
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses and can radiate radio  
frequency energy and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off  
and on, the user is encouraged to try to correct the interference by one or  
more of the following measures:  
- Reorient or relocate the receiving antenna.  
- Increase the separation between the equipment and receiver.  
- Connect the equipment into an outlet on a circuit different form that to which  
the receiver is connected.  
- Consult the dealer or an experienced radio/ TV technician for help.  
Shielded interface cables and AC power cord, if any, must be used in order  
to comply with emission limits.  
Changes or modifications not expressly approved by the party responsible  
for compliance could void the user‘s authority to operate the equipment.  
SAFETY PRECAUTIONS  
1. Do not modify the three-prong grounding type monitor power plug in any way.  
2. Operate this unit only from the type of power source indicated on the label.  
3. Do not block or cover ventilation openings on the back or bottom of the  
monitor cabinet.  
4. Do not place this monitor near a radiator or heating vent.  
5. Do not push objects of any kind through cabinet openings. This may result in  
fire or electrical shock.  
6. Before adding attachments always ask a service technician to perform  
routine safety tests to determine that equipment is in safe operating  
condition. Ground potential tests should be part of the routine safety check  
made by the service technician.  
7. Do not place monitor on an unstable cart, stand, or shelf where it may fall  
and injure personnel or damage equipment.  
2
8. Route power cords so that they cannot be walked upon or tripped over. Do  
not allow anything to rest on the power cord.  
9. Do not install monitor in wet areas, or where it may be exposed to rain or  
water. Do not spill liquid of any kind on the unit.  
10. Unplug the power cord from the unit before cleaning the display. Use only  
a damp cloth. Do not use alcohol, spirits, or ammonia to clean the display.  
DO NOT ATTEMPT TO CLEAN THE INTERIOR OF THIS UNIT-THIS ACTION  
MUST BE PERFORMED BY THE SERVICE TECHNICIAN AS REQUIRED  
DURING NORMAL MAINTENANCE.  
11. Refer all servicing to qualified service personnel. REMOVAL OF BACK  
COVER BY UNAUTHORIZED PERSONNEL MAY EXPOSE THE USER TO  
DANGEROUS VOLTAGES OR OTHER HAZARDS.  
12. Unplug the unit immediately and notify the service technician.  
A. If liquid has been spilled into the display or the display has been  
exposed to rain or water.  
B. If the unit has been dropped or the cabinet damaged.  
C. If fuses continue to blow.  
D. If the power cord is damaged or frayed.  
E. If a distinct change from normal operation is apparent.  
When replacement parts are required, be sure that the service technician  
uses components specified by the manufacturer which have the same  
characteristics as the original parts. UNAUTHORIZED SUBSTITUTIONS MAY  
RESULT IN FIRE, ELECTRICAL SHOCK OR OTHER HAZARDS.  
Upon completion of any service or repairs, ask the technician to perform  
safety checks to determine that the equipment is in safe operating condition.  
WARNING: SERIOUS SHOCK HAZARDS EXIST WITHIN THE COVERS OF  
THIS MONITOR. DO NOT OPEN THE COVERS UNDER ANY CIRCUMSTANCES,  
THERE ARE NO USER SERVICEABLE COMPONENTS INSIDE  
3
1.GENERAL FEATURES  
This is a high performance 15" TFT LCD monitor with a 1024x768 XGA resolution. The LCD monitor  
has been designed for use with both PC and security systems, comply with the power management  
regulations of VESA DPMS, supported by Plug & Play, complying with DDC1/2B.  
FEATURES  
90~264V AC Power Supply  
NTSC/PAL Auto-Detector  
High Resolution  
PC Input  
Dual Video Input/Output  
Dual Audio Input/Output  
Y/C Input  
Up to 16M Colors  
Built-in Auto Channel Scanning  
OSD With Multiple Languages  
Wall Mountable  
4
2.SETTING UP  
Read this chapter for important safety information and how to set up and connect the display to your  
computer or camera.  
¾Check the attachment of monitor. There are power cord, user’s manual and PC signal cable.  
¾Make sure the surface for placing the LCD monitor is stable and level.  
¾Keep the monitor away form sources of liquids and moisture.  
¾Keep the monitor’s vents free from obstruction.  
¾If you will not be using the monitor and computer for a day or more, make sure to turn off the  
computer and turn off the main switch of the monitor.  
2.1 CONNECT THE MONITOR TO YOUR COMPUTER  
¾Make sure the computer is turned off.  
¾Plug in the monitor.  
¾Connect the PC signal cable of the computer to the monitor.  
¾Turn on the computer.  
¾Turn on the main switch of the monitor.  
¾Push the power button in front of the monitor.  
¾Push the channel button to display PC input signal.  
2.2 CONNECT THE MONITOR TO THE VIDEO SOURCE  
¾Plug in the monitor.  
¾Connect the video signal to the monitor.  
¾Turn on the main switch of the monitor.  
¾Push the power button in front of the monitor.  
¾Push the channel button to display video input signal.  
5
3.CONTROLS AND INDICATORS  
3.1 FRONT PANEL  
a. CHANNEL BUTTON  
¾Select channel ¾Press this button to choose the channel to be displayed.  
¾Auto scan ¾Press the button over 2 seconds until the power LED changes to yellow color.  
b. MENU BUTTON  
¾Press the button to show the main OSD menu.  
¾Press the button for the second time to show the sub OSD menu after the main menu is elected.  
c.  
¾Press  
BUTTONS  
buttons to select an icon in the main menu.  
buttons to adjust the selected icon value in sub menu.  
¾Press  
d. POWER LED  
¾Green – Power on  
¾Dark – Power off  
¾Yellow – Auto scan mode  
¾Yellow (Flashing) – Power saving  
e. POWER BUTTON ¾Press the button to turn on or turn off the monitor.  
6
3.1 BOTTOM PANEL  
a. PC input  
b. Y/C input  
c. Video(CVBS) 1 input  
d. Video(CVBS) 1 output  
e. Video(CVBS) 2 input  
f. Video(CVBS) 2 output  
g. Audio L input  
h. Audio L output  
i. Audio R input  
j. Audio R output  
7
4
ON SCREEN DISPLAY (OSD)  
4.1  
PC MODE  
Press  
buttons to select an icon, then Press MENU button to change the values  
in the sub menu.  
C O N T R A S T  
>>>  
RGB  
(((  
)))  
EXIT  
1 0 2 4 X 7 6 8  
4 8 K  
6 0 H Z  
CONTRAST ¾Press  
buttons to adjust the contrast value, then press MENU  
buttons to adjust the brightness value, then press  
button to return to the main menu.  
BRIGHTNESS ¾Press  
MENU  
button to return to the main menu.  
H POSITION ¾Press  
buttons to adjust the horizontal position value of the  
image, then press MENU button to return to the main menu.  
V POSITION ¾Press  
buttons to adjust the vertical position value of the image,  
then press MENU button to return to the main menu.  
| | |  
PHASE ¾Press  
buttons to adjust the phase value, then press MENU button to  
return to the main menu.  
>>>  
CLOCK ¾Press  
buttons to adjust the clock value, then press MENU button to  
8
return to the main menu.  
9
RGB  
COLOR ¾Press  
buttons to select a color and press  
buttons to  
adjust the value of selected color, then press MENU button to return to the main menu.  
AUTO ADJUST ¾Automatic adjusting of H position, V position, phase and clock values.  
TRUE COLOR ¾True color can upgrade the panel’s color from 262K to 16M and vice  
versa.  
VOLUME ¾Press  
buttons to adjust the volume value, then press MENU  
(((  
)))  
button to return to the main menu.  
OSD H POSITION ¾Press  
buttons to adjust the horizontal location of OSD,  
then press MENU button to return to the main menu.  
OSD V POSITION ¾Press  
buttons to adjust the vertical location of OSD,  
then press MENU button to return to the main menu.  
LANGUAGE ¾Select the language to be used in OSD.  
RECALL COLOR ¾Recall the values of R,G,B colors. Set the color temperature of the  
LCD monitor for the CIE coordinate 9300˚k or 6500˚k.  
RECALL MODE DATA ¾Recall the H position, V position, phase and clock values of the  
mode data.  
EXIT  
EXIT ¾Exit OSD menu.  
10  
4.2 Video mode  
Press  
buttons to select a icon, then Press MENU button to change the  
values in sub menu.  
B R I G H T N E S S  
RGB  
(((  
)))  
>>  
EXIT  
C V B S 1  
I N P U T  
BRIGHTNESS ¾Press  
buttons to adjust the brightness value, then press  
MENU button to return to the main menu.  
CONTRAST ¾Press  
buttons to adjust the contrast value, then press MENU  
button to return to the main menu.  
RGB  
COLOR ¾Press  
buttons to adjust the color value, then press MENU button  
to return to the main menu.  
TINT ¾Press  
return to the main menu.  
buttons to adjust the tint value, then press MENU button to  
buttons to adjust the sharpness value, then press  
SHARPNESS ¾Press  
>>>  
MENU button to return to the main menu.  
(((  
))  
VOLUME ¾Press  
buttons to adjust the volume value, then press MENU  
)
button to return to the main menu.  
SEQUENCE TIME ¾Press  
buttons to adjust the sequence time value, then  
press MENU button to return to the main menu. Sequence time is the displaying time for  
each channel in auto scan mode.  
11  
TRUE COLOR ¾True color can upgrade the panel’s color from 262K to 16M and vice  
versa.  
OSD H POSITION ¾Press  
buttons to adjust the horizontal location of OSD,  
then press MENU button to return to the main menu.  
OSD V POSITION ¾Press  
buttons to adjust the vertical location of OSD,  
then  
press MENU button to return to the main menu.  
LANGUAGE ¾Select the language to be used in OSD.  
RECALL ¾Reset all of the values to factory preset values.  
TITLE ENABLE ¾Enable to show the title message while OSD menu disappear.  
TITLE EDITING ¾Editing title message of the channel. Select a channel then press MENU  
button into next sub menu  
.
T I T L E  
E D I T I N G  
Y / C  
C V B S 1  
C V B S 2  
EXIT  
There are 16 characters that can be edited in each channel. Press  
select character on location and press  
then press MENU button to return to the sub menu.  
buttons to  
buttons to change the character in that location,  
T I T L E  
E D I T I N G  
C V B S 1  
F R O N T  
D O O R  
EXIT  
EXIT ¾Exit OSD menu.  
5.SPECIFICATIONS  
12  
Type  
LCD Panel  
15TFT Color  
262K colors  
Colors  
Viewable Size  
Dot Pitch  
15" 304.1mm (H) x 228.1mm (V)  
0.297mm x 0.297mm  
60/60/45/55  
Viewing Angle(L/R/T/B)  
Contrast Ratio  
Brightness  
300:1  
200 cd/m2  
Resolution  
1024 x 768  
User's Controls  
Power  
Power, Channel, Menu, Up, Down, Left, Right  
Power, Auto_Adj, Menu, Up, Down, Left, Right  
Input voltage  
AC 90 to 264V ( 60 / 50Hz) or DC 12V  
Consumption  
Normal: 35W(max); Standby: 5W(max)  
Agency Approval  
Others  
ETL, ETL-C, FCC, CE  
Weight  
5kg(NW), 6.5kg(GW)  
Dimensions  
(WxHxD)mm  
Depth  
395x395.3x182.1(Physical),  
468x508x268(Package)  
70mm  
Temperature  
Operating Conditions  
Storage Conditions  
10  
20 % to 85 % (Non-condensation)  
-20 to 60  
to 40  
Humidity  
Temperature  
Humidity  
5 % to 95 % (Non-condensation)  
Level 0.7Vp-p / 1KHz (typical), RCA Jack  
Loop-through type, RCA Jack  
Audio x 2  
Audio x 2  
Audio Input  
Output  
Stereo 2 x 1 watts, built-in speakers  
Video(CVBS) x 2  
Capability  
Video Input  
Composite video 1.0Vp-p / 75, RCA Jack  
Y/C x 1  
Level 1.0Vp-p / 75, Mini-din 4pin connector  
Video(CVBS) x 2  
Output  
OSD  
Loop-through with buffered circuit, RCA Jack  
Brightness, Contrast, Color, Tint, Sharpness, Volume, Sequence Time  
True Color, OSD H Position, OSD V Position, Language, Recall, Title  
Enable  
Title Editing, Exit  
Operation System  
Compatibility  
NTSC M / PAL BGHI  
Scanning Frequency  
NTSC 15750Hz ± 500Hz / 60Hz  
PAL 15625Hz ± 500Hz / 50Hz  
PC  
Input  
OSD  
Analog RGB signal : 0.707Vp-p / 75, D-sub 15 pin  
Contrast, Brightness, H Position, V Position, Phase, Clock, Color, Auto  
Adjust  
True Color, Volume, OSD H Position, OSD V Position, Language, Recall  
Color  
Recall Mode Data, Exit  
DDC1/2B  
Plug & Play  
VESA DPMS  
Power Management  
Supported Timing  
640x350x70Hz  
640x480x60Hz  
640x480x75Hz  
720x400x85Hz  
800x600x72Hz  
832x624x75Hz(MAC)  
1024x768x75Hz  
640x400x70Hz  
640x480x72Hz  
720x400x70Hz  
800x600x60Hz  
800x600x85Hz  
1024x768x70Hz  
1024x768x85Hz  
640x400x56Hz  
640x480x66Hz(MAC)  
640x480x85Hz  
800x600x56Hz  
8800x600x75Hz  
1024x768x60Hz  
1024x768x75Hz(MAC)  
13  
3121-0301-03  
REV: 01  
-15-  

Toshiba MK6017MAP User Manual
Tokina MOTORIZED ZOOM LENS TM7Z0818GAIDC User Manual
Telex Car Stereo System FM 1 User Manual
Tamron Camera Accessories A20 User Manual
Sony VCL HG1730A Telephoto Conversion Lens VCLHG1730A User Manual
Sony CDX GT56UI User Manual
Sennheiser Car Satellite Radio System EK 2000 IEM BW User Manual
Sanyo UF 1311 User Manual
Samsung SCD457 User Manual
Rotel RCD955AX User Manual