Verona CR 43 User Manual

Operation Instructions  
Verona CR 43  
Front Panel Description  
1 ON/OFF  
5 Cassette compartment  
; Preset buttons 1, 2, 3, 4, 5, 6  
Store station - Keep button depressed  
during radio operation until the station  
becomes audible again.  
Switch the set on/off by turning the  
knob.  
If “Cod” appears on the display, read  
the chapter “Anit-Theft Coding” first.  
Volume control:  
6 Track indication  
- side A or 1 is played  
- side B or 2 is played (reverse ope-  
ration)  
Recall station - Briefly press the re-  
spective button.  
By turning the knob  
Coding - Read the “Anti-Theft Coding”  
chapter first.  
Buttons 1 - 4: Use to enter a four-digit  
code number.  
Press each of the buttons until the four-  
digit code to be found in the car radio  
passport is represented on the display.  
SCAN (search operation):  
During radio reception, the stations are  
briefly sampled by pressing the knob for  
approx. one second.  
7 FR button (Fast Rewind)  
Fast rewind of the tape.  
Deactivate: press button FF.  
Balance:  
8 PROG (Autoreverse)  
Pull knob and adjust left/right volume by  
turning the knob.  
For shifting to the other side of the tape  
- press both buttons.  
< lo rocker switch  
Use this button to alter the sensitivity of  
the automatic station seek operation.  
lo lights up on the display - normal sen-  
sitivity  
2
/
rocker switch  
9 FF button (Fast Forward)  
Radio: Automatical station tuning  
Coding: Read first the “Anti-Theft  
Coding” chapter.  
Fast forward of the tape  
Deactivate: press button FR.  
lo does not light up - high sensitivity  
: Press rocker switch  
to confirm your code  
entry.  
: Display for  
Additional function of the lo rocker  
switch:  
Switching from stereo to mono:  
Press longer than 2 seconds.  
3 << / >> rocker switch  
frequency  
waveband  
For fine tuning of the stations  
4
Ejection of the tape  
Press button firmly.  
preset button  
storage level  
stereo  
seek tuning  
(sensitivity)  
13  
= M•L rocker switch (Medium wave -  
Long wave)  
@ TREB (Treble)  
to adjust trebles.  
Use this rocker switch to select either  
medium wave (MW) or long wave (LW)  
frequencies. To switch between these  
wavebands simply press the rocker  
switch again.  
A BASS  
to adjust basses.  
B FAD (Fader)  
(front/rear volume):  
adjust using the lever.  
> FM•T button (Frequency Modulation)  
This button is used for shifting between  
the different FM storage levels I, II, III  
and T (Travelstore - i.e. storing and  
calling the six strongest stations of an  
area).  
Storing “T” - Press the FM •T button  
until the seek tuning indication starts to  
be displayed.  
Recalling “T” - Press the FM•T button  
? until T is indicated on the display.  
Then briefly press the respective preset  
button.“Balance” knob  
To adjust the volume of the left and  
right channel  
? PS rocker switch (Preset Station Scan)  
Pressing this button briefly samples all  
memorized stations of the selected  
waveband (FM, MW, LW or TS).  
14  
Contents  
Important Notes............................ 16  
Radio Section ............................... 18  
What You Should Read By All Means! . 16  
Safety Notes ......................................... 16  
Road Safety ....................................... 16  
Selection of the Desired Waveband...... 18  
Automatic Station Tuning ...................... 18  
Manual Tuning ...................................... 18  
Adjusting the Station Seek Sensitivity... 18  
Adjusting the local mode sensitivity ...... 18  
Switching between Stereo and Mono ... 18  
Storing a Station ................................... 19  
Automatically Storing the Strongest  
Anti-Theft Coding ......................... 16  
Wrong Code Number Entered ........... 16  
First-time Operation and Restart  
Following Interruption of Power  
Supply................................................ 16  
Switching Code System Off ............... 17  
Switching the Code System Back On If  
you wish to re-activate the anti-theft  
code system: ..................................... 17  
Optical indication of theft protection .. 17  
Stations ................................................. 19  
Activating a Stored Station.................... 19  
Briefly Sampling a Station ..................... 19  
Sampling Memorized Stations .............. 19  
Tape Section ................................. 20  
Inserting the Tape ................................. 20  
Removing the Tape............................... 20  
Fast Forwarding/Rewinding of the Tape 20  
Autoreverse........................................... 20  
Care Notes ............................................ 21  
Amplifier Section.......................... 17  
ON/OFF ................................................ 17  
Balance Control .................................... 17  
Fader control ......................................... 17  
Appendix ....................................... 21  
Technical Data ...................................... 21  
15  
Important Notes  
Anti-Theft Coding  
our central customer service workshop or to  
one of our dealers in your vicinity.  
What You Should Read By All  
Means!  
Your radio is protected against theft by an  
anti-theft coding system. If, once the unit has  
been encoded, the power is disconnected  
from the set (e.g. theft, disconnection of the  
car battery or prior to installation), the set is  
Beforestartingtouseyournewcarradio, you  
should carefully read through the safety no-  
tes and the information about “Anti-Theft  
Coding”.  
First-time Operation and Restart Follo-  
wing Interruption of Power Supply  
electronically blocked. It may only be used Switch on set.  
again after the appropriate code number has  
been entered (see car radio pass). Hence, a  
coded set is of no use to a potential thief.  
“Cod” will appear in the display :.  
Briefly press preset button 1 ;, “000”  
Safety Notes  
will appear in the display :.  
Road Safety  
Enter the code number from the Blau-  
Beingthedriverofamotorvehicleyoushould Wrong Code Number Entered  
punkt car radio pass:  
dedicateyourfullattentiontothetrafficaround  
you. Therefore always use your car stereo  
such that you are able to cope with the  
present traffic situation in any moment.  
In difficult driving situations you should turn  
your set off. Please take into account that at  
a speed of 50 km/h you are almost covering  
a distance of 14 m per second!  
When adjusting the volume, always make  
sure that acoustic signals from the outside  
can still be heard in order to be able to react  
to alert signals just as it is required by the  
present situation.  
It should not be possible for thieves to ascer-  
tain the code number by trial-and-error. This  
is why the set is blocked for a certain period  
of time if an incorrect code number is ente-  
red. “---” would then appear in the display:.  
This time period is 10 seconds following the  
first three attempts, and is increased to 1  
hour following subsequent attempts.  
Example: Code number is 1521  
- press preset button 1 ; once,  
“1000” appears in the display :,  
- press preset button 2 ; 5 times,  
“1500” appears in the display :,  
- press preset button 3 ; 2 times,  
“1520” appears in the display :,  
- press preset button 4 ; once,  
“1521” appears in the display :.  
After 19 unsuccessful attempts “OFF” will  
appear in the display : and the set can no  
longer be started.  
Confirm code number:  
Press upper part of rocker switch  
/
Note:  
2.  
Keep your car radio pass, which contains the  
codenumber, inasafeplaceinordertoavoid  
“unauthorized access” to your car radio. If  
you lose your radio pass and have forgotten  
your code number you will not be able to  
restart the set after the power supply has  
been interrupted. The only way to make the  
set operable again is by sending the radio to  
Note:  
Using preset button 1 the set can only be  
adjustedto1or0”.0isnotindicatedinthe  
display.  
If you have entered and confirmed an incor-  
rect code number, “---” will initially appear in  
the display : and then, after a certain time  
16  
Amplifier Section  
period, “000”. Following this, it is essential  
that you enter the correct code number.  
ON/OFF  
The anti-theft code system is now activated.  
Now whenever the set is turned on, “CODE”  
will appear briefly in the display :.  
For switching the set on,  
turn button 1  
.
Switching Code System Off  
If you wish to switch the anti-theft code sy-  
stem off:  
Your stereo is now ready for operation.  
Optical indication of theft protection  
As optical warning of the encoded car radio,  
For switching the set off,  
turn off the radio,  
the LED  
6 flashes when the ignition is  
turn button 1  
.
switched off, provided the car radio has been  
connected correspondingly.  
Forthis, pleaseseethecorrespondinginstal-  
lation instructions.  
simultaneously press, and hold, preset  
buttons 1 and 4 ;  
Volume control  
turn the set back on. “Cod” will then  
turn button 1.  
appear in the display :.  
release the preset buttons 1 and 4 ;.  
Balance Control  
“000” then appears in the display :.  
Use button 1 to balance the sound impres-  
sion of the right and left channel speaker.  
Enter the code number that is in the  
Blaupunkt car radio pass and confirm:  
See example “First-time operation ...”.  
Pull (lock in) button and turn.  
The anti-theft coding system has now been  
deactivated.  
After the adjustment  
slightly press button.  
Switching the Code System Back On If  
you wish to re-activate the anti-theft  
code system:  
Fader control  
If four loudspeaker are connected, the front/  
rear sound impression of the loudspeakers  
(fader) can also be modified using lever B.  
turn the radio off,  
simultaneously press, and keep de-  
pressed, preset buttons 1 and 4 ;,  
turn the set back on. “Cod” briefly ap-  
pears in the display : and then the set  
is switched on.  
Adjusting trebles  
turn button @.  
Adjusting basses  
turn button A.  
17  
Radio Section  
Tuning of Previous Station  
Press rocker switch  
Selection of the Desired Wave-  
band  
Adjusting the local mode sensiti-  
/
2 down. The vity  
radio will automatically seek the previ-  
ous station.  
This radio allows you to choose between the  
FM, MW and LW wavebands.  
In regions with extremely high station densi-  
ty, e.g. in Italy, the set allows you to switch  
over the station seek sensitivity for the ocal  
mode from “High” (adjusted ex works) to  
“Low”. “Low” means that station seek tuning  
only captures the most powerful stations.  
For modifying the local mode:  
If the rocker switch  
/
2 is held  
down/up, the seek operation continues  
to be carried out quickly in the corre-  
sponding direction.  
FM Selection  
Briefly press the FM•T rocker switch  
>. “FM” is displayed in the display (for  
Frequency Modulation).  
Manual Tuning  
press button lo < longer than 8 secs.  
Itisalsopossibletotuneinstationsbyhand”  
with this radio:  
The display : shows “L” for “Low”.  
By pressing button lo < again longer than  
MW or LW Selection  
Briefly press the M•L rocker switch =.  
An “M” (for MW), or an “L” (for LW) will  
then appear in the display.  
Press rocker switch <</>> 3 to the left 8 secs., the set switches back to “High” (dis-  
or to the right. The frequency band is  
scanned in small steps.  
play : “H”).  
Whenswitchingofftheunitorwhenremoving  
the set with the QuickOut handle the set  
remains in the last activated mode.  
If you wish to switch between MW and LW:  
press the M•L rocker switch = again.  
The following instructions apply for all wave-  
bands, as long as not otherwise indicated.  
Adjusting the Station Seek  
Sensitivity  
Switching between Stereo and  
Mono  
You may also modify the sensitivity of the  
automatic station seek operation.  
For this:  
Automatic Station Tuning  
If you wish to switch between stereo and  
mono:  
Tuning of Subsequent Station  
press lo rocker switch <.  
If “lo” is indicated, only stations with  
good reception conditions are captured  
(lower sensitivity).  
Press rocker switch  
/
2 up. The  
keep the lo button < pressed for long-  
er than 2 seconds. The stereo symbol  
will appear in the display : if the  
stereo mode is activated.  
radio will automatically seek the next  
station.  
If “lo” is not indicated, stations with a  
weaker reception are also captured  
(higher sensitivity).  
The stereo function is activated auto-  
matically when you turn your set on.  
The set will automatically switch to  
mono if reception is poor.  
18  
Storing a Station  
Automatically Storing the Stron- Briefly Sampling a Station  
gest Stations  
You can store one MW and LW station and 4  
(Radio Scan)  
FMstationsoneachofthepresetbuttons;. (Travelstore)  
Starting with the currently tuned in station,  
The display will show you the selected wa- WithTravelstore, youhavetheopportunityto you can have the following ones briefly sam-  
veband (FM, MW or LW) and preset button. automatically store the six most powerful FM pled for approx. eight seconds each.  
On FM, the display will also give you the stationsofyourlocalreceptionareaandhave  
chosen storage level (I, II, III or T). them sorted according to their frequencies.  
If you wish to change from one storage level This feature is of special use while travelling.  
Press the knob 1 for approx. 1 sec.  
If the following station is found, it is  
reproduced for approximately eight  
seconds.The station’s frequency starts  
blinking on display :; if it has already  
been memorized, the corresponding  
preset button and the storage level indi-  
cator starts blinking on display :. Sub-  
sequently, the set starts searching for  
the next station.  
to another:  
Press the FM•T rocker switch > for at  
least two seconds.  
press the FM•T button >.  
If you wish to store a station:  
The set searches for the next FM stati-  
ons and sorts them on the “T” (Travel-  
store) storage level. Once the process  
is finished, the car radio tunes in to the  
first station.  
(for FM only) select the storage level.  
To achieve this, press the FM•T button  
> until I,II,III or T appears in the dis-  
play :.  
If required, it is also possible to manually For selecting a sampled station:  
tune in the station (see chapter Station  
storeastationontheTravelstorelevel. Ifless  
than five stations can be received, the free  
buttons are represented by dashes for a  
short period of time.  
Press the knob 1 once again. The  
Tuning).  
Scan function is off.  
press the desired preset button ; until  
the radio resumes play (approx. 2 se-  
conds).  
After the search operation has been conclu-  
ded, and no station has been chosen, the  
radio starts playing the station from which  
Station Scan was started before.  
The display : indicates which preset  
button has been pressed.  
The station has now been stored.  
Activating a Stored Station  
If required, the memorized stations can be  
activated at a keystroke.  
Sampling Memorized Stations  
Choose the storage level.  
For this, press FM•T > until the dis-  
play : shows I, II or III, or T.  
Note:  
Allmemorizedstationsofawavebandcanbe  
briefly sampled.  
When tuning in an already stored station, the  
display : will show the corresponding pre-  
set button for approx. five seconds and the  
respective storage level.  
Press the PS rocker switch ?.  
Briefly press the required preset button  
One after another, the car radio will  
then start introducing all memorized  
stations of the selected waveband.  
;.  
19  
Tape Section  
The set either samples the stations of  
storage levels I-III or of the Travelstore  
level “T”. This depends on the current  
switching status.  
Fast Rewind  
Inserting the Tape  
Press the FR (Fast Rewind) button 7.  
Once the tape has been completely  
rewound, the set begins playing the  
tape.  
If you wish to play a cassette tape:  
switch the set on  
gently insert the cassette with side 1  
If a preset button has no station alloca-  
ted, this button is skipped.  
upwards.  
The tape will then be played in the direction  
it was last played.  
Track indication 6 indicates which side is  
played.  
- side A or 1 is played.  
- side B or 2 is played (reverse operation).  
Stopping the Fast Rewind Operation  
To terminate this function:  
Press the PS rocker switch ? once  
again.  
Press the FF button 9.  
Autoreverse  
The station currently sampled is  
maintained.  
If, while a tape is playing, you wish to switch  
to the other side of that tape:  
Removing the Tape  
press the FF and FR buttons simulta-  
neously.  
If you wish to remove the tape:  
Attheendofthetapethesetwillautomatical-  
ly switch to the other side of the tape.  
press the  
then ejected.  
button 4. The tape is  
Note:  
Fast Forwarding/Rewinding of  
the Tape  
When playing stiff tapes it is also possible to  
manually switch to the other side of the tape.  
If this is the case, check the tape wound up to  
that point; fast forwarding or rewinding often  
helps in such cases.  
Fast Forward  
Press the FF (Fast Forward) button 9.  
At the end of the tape the set will switch to  
the other side and resume playing the  
tape.  
Stopping the Fast Forward Operation  
Press the FR button 7.  
20  
Appendix  
Care Notes  
Technical Data  
We recommend C-60 and C-90 type tapes  
for use in any automobile tape player; to  
protectyourtapes,storetheminacoolplace  
away from dirt, dust, or excessive tempera-  
tures above 50° Celsius. In order to ensure  
smoothtapeoperation,coldtapesshouldbe  
allowed to heat up a bit before they are  
played. If dust collects on the audio head or  
the rubber roller, problems related to rough  
tape operation or poor sound quality may  
occur after approx. 100 hours of operation.  
For normal contamination, use a head-  
cleaning cassette to remove the dust; for  
more intensive contamination, use a cotton-  
wooltipsoakedwithalcohol.Neverusehard  
tools!  
Amplifier  
Output power:  
4 x 4.5 W watts RMS  
acc. to DIN 45324/3.1  
4  
FM:  
Sensitivity:  
0.9 µV at 26 dB  
signal-to-noise ratio  
Frequency  
response:  
35 - 15 000 Hz (-3 dB)  
31.5 - 16 000 Hz (-3 dB)  
Tape Section:  
Frequency  
response:  
Modifications reserved!  
21  
Blaupunkt-Werke GmbH  
Bosch Telecom  
1/93  
MC/VKD-Hi 3 D92 147 061  
PM  

Vivitar ViviCam F529 User Manual
Vivitar Camera Lens VIV 7MM P User Manual
Speco Technologies VM 1201W User Manual
Sony WM FX288 User Manual
Sony Handycam 4 170 095 1100000000#User Manual
Sony DCR DVD508 User Manual
Sony CYBER SHOT DSC S730 User Manual
Sony ACTIVE SUBWOOFER SA W2500 User Manual
SanDisk ImageMate User Manual
Samsung Blu ray Player BD E5900 User Manual