Toshiba MA 156 1 User Manual

TEC Electronic Cash Register  
MA-156-1 SERIES  
Table of Contents  
EO1-11099  
Safety Summary  
Safety Summary  
Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions  
necessary for safe handling are included in this manual. All warnings and cautions contained in this  
manual should be read and understood before handling or maintaining the equipment.  
Do not attempt to effect repairs or modifications to this equipment. If a fault occurs that cannot be rectified  
using the procedures described in this manual, turn off the power, unplug the machine, then contact your  
authorized TOSHIBA TEC representative for assistance.  
Meanings of Each Symbol  
This symbol indicates warning items (including cautions).  
Specific warning contents are drawn inside the symbol.  
(The symbol on the left indicates a general caution.)  
This symbol indicates prohibited actions (prohibited items).  
Specific prohibited contents are drawn inside or near the symbol.  
(The symbol on the left indicates “no disassembling”.)  
This symbol indicates actions which must be performed.  
Specific instructions are drawn inside or near the symbol.  
(The symbol on the left indicates “disconnect the power cord plug from the outlet”.)  
This indicates that there is the risk of death or serious injury if the  
machines are improperly handled contrary to this indication.  
WARNING  
Any other than the  
specified AC voltage  
is prohibited.  
Do not plug in or unplug the power  
cord plug with wet hands as this may  
cause electric shock.  
Do not use voltages other than the  
voltage (AC) specified on the rating  
plate, as this may cause fire or  
electric shock.  
Prohibited  
Prohibited  
Prohibited  
If the machines share the same  
outlet with any other electrical  
appliances which consume large  
amounts of power, the voltage will  
fluctuate widely each time these  
appliances operate. Be sure to  
provide an exclusive outlet for the  
machine as this may cause the  
machines to malfunction.  
Do not place metal objects or  
water-filled containers such as flower  
vases, flower pots or mugs, etc. on  
top of the machines. If metal objects  
or spilled liquid enter the machines,  
this may cause fire or electric  
shock.  
Prohibited  
Do not insert or drop metal,  
flammable or other foreign objects into  
the machines through the ventilation  
slits, as this may cause fire or electric  
shock.  
Do not scratch, damage or modify  
the power cords. Also, do not place  
heavy objects on, pull on, or exces-  
sively bend the cords, as this may  
cause fire or electric shock.  
Prohibited  
Disconnect  
the plug.  
Disconnect  
the plug.  
If the machines are dropped or their  
cabinets damaged, first turn off the  
power switches and disconnect the  
power cord plugs from the outlet, and  
then contact your authorized  
TOSHIBA TEC representative for  
assistance. Continued use of the  
machine in that condition may cause  
fire or electric shock.  
Continued use of the machines in an  
abnormal condition such as when the  
machines are producing smoke or  
strange smells may cause fire or elec-  
tric shock. In these cases, immedi-  
ately turn off the power switches and  
disconnect the power cord plugs from  
the outlet. Then, contact your author-  
ized TOSHIBA TEC representative for  
assistance.  
(i)  
EO1-11099  
Safety Summary  
Disconnect  
the plug.  
Disconnect  
the plug.  
If foreign objects (metal fragments,  
water, liquids) enter the machines,  
first turn off the power switches and  
disconnect the power cord plugs from  
the outlet, and then contact your  
authorized TOSHIBA TEC repre-  
sentative for assistance. Continued  
use of the machine in that condition  
may cause fire or electric shock.  
When unplugging the power  
cords, be sure to hold and pull on  
the plug portion. Pulling on the cord  
portion may cut or expose the inter-  
nal wires and cause fire or electric  
shock.  
Connect a  
grounding  
wire.  
No  
Ensure that the equipment is  
properly grounded. Extension cables  
should also be grounded. Fire or  
electric shock can occur on improp-  
erly grounded equipment.  
Do not remove covers, repair or  
modify the machine by yourself. You  
may be injured by high voltage, very  
hot parts or sharp edges inside the  
machine.  
disassembling.  
Unauthorized modification is prohib-  
ited.  
This indicates that there is the risk of personal Injury or damage to  
CAUTIONobjects if the machines are improperly handled contrary to this indication.  
Precaution  
The following precautions will help to ensure that this machine will continue to function correctly.  
Try to avoid locations that have the following adverse conditions:  
*
*
Temperatures out of the specification  
Shared power socket  
*
*
Direct sunlight  
Excessive vibration  
*
*
High humidity  
Dust/Gas  
Do not subject the machine to sudden shocks.  
Do not press the keys too hard. Keys will operate correctly if they are touched lightly.  
Clean the cover and keyboard, etc. by wiping with a dry cloth or a cloth soaked with detergent and wrung out  
thoroughly. Never use thinner or other volatile solvent for cleaning.  
At the end of the day, turn the power OFF, then clean and inspect the exterior of the machine.  
Try to avoid using this equipment on the same power supply as high voltage equipment or equipment likely to  
cause mains interference.  
USE ONLY TOSHIBA TEC SPECIFIED consumables.  
DO NOT STORE the consumables where they might be exposed to direct sunlight, high temperatures, high  
humidity, dust, or gas.  
When moving the machine, take hold of the drawer and lift the machine.  
Do not place heavy objects on top of the machines, as these items may become unbalanced and fall causing  
injury.  
Do not block the ventilation slits of the machines, as this will cause heat to build up inside the machines and  
may cause fire.  
Do not lean against the machine. It may fall on you and could cause injury.  
Request Regarding Maintenance  
Utilize our maintenance services.  
After purchasing the machines, contact your authorized TOSHIBA TEC representative for assistance once per year or  
so to have the inside of the machines cleaned. Otherwise, dust will build up inside the machines and may cause fire or  
malfunction. Cleaning is particularly effective before humid rainy seasons.  
Our maintenance service performs the periodic checks and other work required to maintain the quality and  
performance of the machines, preventing accidents beforehand.  
For details, please consult your authorized TOSHIBA TEC representative for assistance.  
Using insecticides and other chemicals  
Do not expose the machines to insecticides or other volatile solvents, as this will deteriorate the cabinet or other parts  
or cause the paint to peel.  
(ii)  
EO1-11099  
TABLE OF CONTENTS  
Page  
1. Introduction .................................................................................................................................... 1  
2. Unpacking ....................................................................................................................................... 2  
3. Outline of Preparation Procedure Before Operating the ECR ................................................... 3  
4. Appearance and Nomenclature .................................................................................................... 5  
5. Mode Select Switch ........................................................................................................................ 5  
6. Display............................................................................................................................................. 6  
7. Keyboard ......................................................................................................................................... 7  
Functions of Each Key .............................................................................................................................................7  
9. Programming ................................................................................................................................ 11  
System Option Setting ...........................................................................................................................................12  
Department Status Setting .....................................................................................................................................14  
Time Setting ...........................................................................................................................................................15  
Date Setting ...........................................................................................................................................................15  
Department HALC Setting .....................................................................................................................................16  
Secret Code Setting ...............................................................................................................................................17  
% Rate Setting .......................................................................................................................................................17  
PLU Setting ............................................................................................................................................................18  
PLU Deletion ..........................................................................................................................................................19  
Amount Format Setting ..........................................................................................................................................19  
Tax Table Setting....................................................................................................................................................20  
10. Verification of Programmed Data................................................................................................ 24  
11. Daily Operation Flow.................................................................................................................... 25  
12. Transaction Entries ...................................................................................................................... 26  
When an error has occurred ... ..............................................................................................................................26  
Displaying the Time................................................................................................................................................26  
No-sale...................................................................................................................................................................27  
Sale Item Entries (Department Entries) .................................................................................................................27  
Sale Item Entries (PLU Entries) .............................................................................................................................28  
Dollar Discount.......................................................................................................................................................30  
Percent Discount or Percent Charge .....................................................................................................................30  
Void ........................................................................................................................................................................31  
Returned Merchandise...........................................................................................................................................31  
Non-add Number Print ...........................................................................................................................................32  
Subtotal Read and Print .........................................................................................................................................32  
Finalizing a Sale.....................................................................................................................................................32  
Tax Exemption .......................................................................................................................................................35  
Received-on-Account Payment .............................................................................................................................35  
Paid Out .................................................................................................................................................................35  
13. Read (X) and Reset (Z) Reports .................................................................................................. 39  
14. Maintenance.................................................................................................................................. 39  
Replacing the Paper Roll .......................................................................................................................................39  
Replacing the Ink Roller .........................................................................................................................................40  
Manual Drawer Release ........................................................................................................................................40  
Removing the Drawer ............................................................................................................................................41  
Battery Exchange...................................................................................................................................................41  
15. Specifications ............................................................................................................................... 42  
CAUTION:  
1. This manual may not be copied in whole or in part without prior written permission of  
TOSHIBA TEC.  
2. The contents of this manual may be changed without notification.  
3. Please refer to your local Authorized Service representative with regard to any queries  
you may have in this manual.  
EO1-11099  
1. Introduction  
Thank you for choosing the MA-156 series. This instruction manual provides a  
description of the functions and handling of this register and should be read carefully  
toensureoptimumperformance. Sinceeveryconsiderationhasbeengiventosafety  
and reliability, there is no danger of damaging the machine by incorrect operation.  
Please refer to this manual whenever you have any questions concerning the  
machine. This machine has been manufactured under strict quality control and  
should give you full satisfaction. However, if the machine is damaged during transit,  
or there are any unclear points in this manual:  
For supplies, service or assistance call:  
Please have the following information available when you  
call:  
Product:  
Model:  
Electronic Cash Register  
MA-156-1  
Serial Number:  
Place Purchased:  
Date of Purchase:  
Ifforanyreasonthisproductistobereturnedtothestorewhere  
purchased, it must be packed in the original carton.  
• The specifications described in this manual may be modified by the manufacturer,  
if necessary.  
• Be sure to keep this manual for future reference.  
- 1 -  
EO1-11099  
2. Unpacking  
5
6
4
3
2
1
1 Journal Take-up Reel (1 pc.)  
2 Paper Roll 57 mm x ø50 mm (1 pc.)  
3 Dry Batteries (SUM-3 1.5V; 3 pcs.)  
4 Printer Cover/Drawer Key (2 pcs.)  
5 Owner's Manual (1 pc.)  
6 Warranty Registration Card (1 pc.)  
- 2 -  
EO1-11099  
3. Outline of Preparation Procedure Before Operating  
the ECR  
This chapter shows the outline of set-up procedure of the ECR before actually starting  
the ECR operation.  
1
Remove the cash register from the carton, referring to  
Chapter “2. Unpacking” on page 2. And take out all  
the parts and accessories.  
2
Remove the tapes and seals that are holding parts or  
protecting the register surfaces.  
3
Plug the power cord of the register into a wall outlet.  
Make sure that the outlet voltage matches that of the  
power required for the register.  
WARNING: Besuretopluginthepowercordfirst, theninsertthe  
batteries.  
4
Detach the Printer Cover and the Battery Cover, then  
insert the batteries (3 pieces). After inserting the  
batteries, attach the Battery Cover.  
WARNING: Be certain to insert the batteries enclosed in the  
package. If they are not insert and the power is  
turned OFF (including a power failure occurrence),  
the sales data and the programmed data will be  
cleared.  
SET  
5
Set the Mode Select Switch to the REG position.  
OFF  
REG  
X
Z
- 3 -  
EO1-11099  
6
7
Install the Receipt or Journal roll (referring to Chapter  
"8. Installing the Paper Roll").  
Set the time and date correctly, referring to "Setting  
the Time and Date" in Chapter 9.  
8
9
Set the tax tables, referring to "Tax Table Setting" in  
Chapter 9.  
Perform other programming operations, such as pro-  
gramming of Departments, according to the require-  
ment of the market and your store (refer to Chapter 9  
and thereafter).  
- 4 -  
EO1-11099  
4. Appearance and Nomenclature  
JournalWindow  
or  
Printer Cover  
Display  
Receipt Outlet  
Power Cord  
Mode Select Switch  
Drawer  
Keyboard  
External Battery  
Kit Connector  
Printer Cover  
Display (Operator and Customer)  
The cover for the Receipt or Journal paper holder  
and the printer.  
Used to confirm the entry contents and the status  
of the register. (page 6)  
Receipt Outlet or Journal Window  
Mode Select Switch  
The receipt for the finalized sale is issued.  
Or, the operator can see which items have already  
been entered through this window.  
The Mode Select Switch is provided inside the  
Printer Cover.  
It selects the type of register operations. (page 5)  
External Battery Kit Connector  
The External Battery Kit (K-BAP-QM) is avail-  
able as an option. By connecting this kit into the  
connector, the register is operable without AC  
power.  
Keyboard  
Used to enter sale items. (page 7)  
Drawer  
Cash and other media are kept here. It automati-  
cally opens on finalizing a sale.  
5. Mode Select Switch  
SET ............Used to program preset data.  
SET  
OFF  
REG  
OFF ............Stops register operations and extinguishes the display. How-  
ever, the power is being supplied to the register.  
X
Z
REG ...........Used to register normal sales .  
X .................Used to read sales totals processed in the register report  
memory (X report). Received-on-Account and Paid Out  
operations are also performed in this position. Also used to  
read preset data.  
Z .................Used to read and reset sales totals in the register report  
memory (Z report).  
- 5 -  
EO1-11099  
6. Display  
Amount  
Message Descriptor in case  
of the mode change error  
Repeat Count  
...  
Department Code  
Message Descriptor  
Description  
Amount  
Displays the numeric data, such as amount, quantity, etc.  
Displays the current time or date when the [X/TIME] key is  
depressed in the REG mode.  
Repeat Count  
Displays the repeat count of the same item being entered.  
The count display shows up from the second entry on, and  
only the last digit will be displayed even if the count exceeds  
nine.  
Displays the Department Code (1 to 8) when the correspond-  
ing Department Key is depressed for any sale item entry.  
Department Code  
(Subtotal)  
Message Descriptor:  
Indicates that the displayed amount is the current  
subtotal of the sale.  
(Total)  
Indicates that the sale is finalized and the displayed  
amount is the sale total.  
(Change)  
Indicates that the sale is finalized with an amount  
tendered and the displayed amount is the change  
due.  
(Negative Mark)  
When a Void, Dollar Discount, Percent Discount, or  
Returned Merchandise item has been entered, the  
Negative Mark is displayed.  
The mark is also displayed when the subtotal or sale  
total is obtained and the amount is negative.  
(Error)  
Indicatesthatthelastoperationhascausedanerror.  
In case of the mode change error, "M" is displayed  
together with "E".  
- 6 -  
EO1-11099  
7. Keyboard  
The following shows the key layout on the MA-156 keyboard:  
FEED  
#
VD  
-
%
7 8  
9
6
1
5
PLU  
X
TAX CHK  
5
4
1
2
3
6
7
RA  
NS  
CH  
ST  
2 3  
00  
PO TIME  
C
AT/TL  
0
4
8
Functions of Each Key  
KEY  
FUNCTION  
Clear Key: Used to clear a wrong entry or operation error.  
C
Multiplication / Time Display Key: Used to enter sale  
items by multiplication inside a sale. Also used to display  
the time outside a sale.  
X
TIME  
Feed Key: Used to feed the receipt or journal paper.  
FEED  
Numeric Keys: Used to enter numeric data, such as  
amounts, quantities, and code numbers.  
The [00] key functions the same as depressing the [0] key  
twice consecutively.  
7
4
1
8
5
2
9
6
3
0
00  
Department Keys 1 to 8: Used to enter sale items and  
process the amount into appropriate departments.  
8
1
to  
- 7 -  
EO1-11099  
KEY  
FUNCTION  
Tax Modifier: Used inside a sale to reverse the Tax status  
of departments, PLUs, Dollar Discount, and Percent  
Charge/Discount from taxable to non-taxable, or vice  
versa.  
TAX  
PercentChargeorDiscountKey: Usedtoaddorsubtract  
a percent rate, preset or manually entered, to or from the  
sale or an individual sale item. Whether the key is used as  
Percent Charge or Percent Discount can be programmed.  
%
Subtotal Key: Used to obtain a subtotal (sale total amount  
up to the moment).  
ST  
CH  
Charge Key: Used to finalize a sale as charge (non-cash  
media sales, such as house charge, credit cards, etc.  
defined by the store) by a simple depression without any  
numeric entry (Total Function only).  
Cash Amount Tender / Total Key: Used to finalize a sale  
as cash by depressing with a prior tendered amount entry  
(Tender Function) or by a simple depression without any  
numeric entry (Total Function).  
AT/TL  
CHK  
VD  
Check Amount Tender/Total Key: Used to finalize a sale  
as check by depressing with a prior tendered amount entry  
(Tender Function) or by a simple depression without any  
numeric entry (Total Function).  
Returned Merchandise/Void Key: Used inside a sale to  
delete items already entered in the current sale. When  
outsideasale, itisusedtorefundmoneytoacustomerwho  
has returned items already purchased.  
Non-add Number Print/Received-on-Account Key (X  
Mode): When depressed with a prior number entry, it  
function as Non-add Number Print Key. When used in X  
mode, it functions to record received-on-account payment  
amounts.  
#
RA  
No-sale/Paid Out Key (X Mode): Used outside a sale to  
open the drawer without relating to a sale. When used in X  
mode, it functions to record amounts paid out of the drawer  
without relating to a sale.  
NS  
PO  
PLU (Price-Look-Up) Key: Used to enter a PLU which is  
linked to a department.  
PLU  
DollarDiscountKey: Usedtosubtractanamountfromthe  
sale such as a discount.  
-
- 8 -  
EO1-11099  
8. Installing the Paper Roll  
WARNING!  
Care must be taken not to injure yourself with the paper cutter.  
1
SET  
OFF  
REG  
Set the Mode Select Switch to REG  
positon.  
X
Z
2
To remove the Printer Cover, insert the  
Printer Cover/Drawer Key to the Printer  
Cover Lock, and then Turn it 90° clock-  
wise.  
3
Cut the paper end to make it sharp.  
4
Hold the paper roll so that the paper end  
will be fed from the bottom.  
- 9 -  
 
EO1-11099  
5
6
Place the paper roll in the paper pocket.  
Insert the paper end into the Paper Inlet  
located on the rear side of the printer, and  
holddownthe[FEED]keyonthekeyboard  
until the paper end comes out of the outlet.  
7
If the printer is used for journal,fold the top  
end of the paper and insert the folded end  
into the slit of the Take-up Reel. Then wind  
the paper two or three times, set the reel to  
the holder, and hold down the [FEED] key  
for a while to tense the paper.  
If the printer is used for receipts, do not  
wind the paper end around the Journal  
Take-up Reel.  
- 10 -  
EO1-11099  
8
If the printer is used for journal, simply  
attach the Printer Cover. The Receipt  
Outlet is used as Journal Window.  
If the printer is used for receipts, attach the  
Printer Cover with the paper end coming  
out of the Receipt Outlet located on the  
Printer Cover.  
9. Programming  
The time and date should be adjusted and such data as status of each department, percent  
rate, etc. should be programmed before starting sale entries. Printing occurs as programming  
is proceeded.  
• Theprogrammeddatawillberetainedbydrybatteriesevenifthepower  
of the machine is turned OFF or a power failure occurs.  
SET  
OFF  
REG  
• Set the Mode Select Switch to the SET position before starting any  
programming operation.  
• Key indications in the operation patterns in this manual:  
X
Z
................... Entry through a Numeric Key  
............................. Function Key depression  
- 11 -  
EO1-11099  
(Available after the Financial Reset (Z) Report is  
taken.)  
System Option Setting  
ST  
HALC for tender amount of the [CHK] key  
1 to 7 (NOTE 1 on the next page)  
Date Entry Order  
0 : Day-Month-Year  
1 : Year-Month-Day  
2 : Month-Day-Year  
Time Print  
0 : Print  
1 : Non-print  
GT Print  
Even Number: Non-print  
Odd Number: Print  
The First Decimal Place Rounding  
Process  
0 or 1 : Round Off  
2 or 3 : Round Up  
4 or more : Round Down  
Credit Balance (NOTE 2 on the next page)  
0 : Prohibited  
1 : Allowed  
Use of the [CHK] key  
0 : Total & Tender Functions  
1 : Total Function only  
2 : Tender Function only  
Use of the [%] key  
0 : %-  
1 : %+  
Use of the Printer  
0 : Journal  
1 : Receipt  
- 12 -  
EO1-11099  
NOTES: 1. HALC (High Amount Listing Capacity) is used to check excessively high  
amounts entered by mistake. For example, if "3" is entered, it means 3  
digits and the high amount limit is 999 ($9.99).  
2. CreditBalancemeansthatamountentriesthroughthe[ - ] keywillresult  
inover-subtractionofthesubtotalamountatthetimeoftheentrythrough  
this key. If the status "Allowed" is selected, over-subtraction using the  
[ - ] key will be allowed. The [VD] key is not subject to this "Credit  
Balance" status selection.  
3. Numeric values in bold face are those of the initial setting.  
Sample Programming Operation  
To set the following system options:  
The printer is used for receipts: 1  
The [%] key is used as the [% -] key: 0  
The [CHK] key is used for "Tender" function only: 2  
Credit Balance is allowed: 1  
GT Print (Print) & The First Decimal Place Rounding Process (Round Up): 3  
Time is printed: 0  
Date Entry Order (Month-Day-Year): 2  
Tender amount through the [CHK] key is allowed up to 5 digits ($999.99): 5  
Key Operation)  
1
0
2
1
3
0 2  
5
ST  
-- Print Sample --  
Values which were  
programmed  
#
10213025  
0002  
Consecutive No.  
Time  
00-00  
00-00-00  
Date  
- 13 -  
EO1-11099  
Department Status Setting  
Repeatable for other department  
3 X/TIME  
TAX  
Dept.  
AT/TL  
Submode No.  
Depress this key only  
when setting a  
Status Code:  
0: Itemized  
department with  
taxable status  
1: Single-item  
(NOTE below)  
NOTES: 1. When a department is set to be an "Itemized" department, a sale item entry  
through that Department Key will not immediately finalize the sale and will  
allow other item entries until a media key ([AT/TL], [CHK] or [CH]) is  
operated.  
Whenadepartmentissettobea"Single-item"department, asaleitementry  
through that Department Key will immediately finalize the sale as cash and  
issue a receipt if it is operated outside a sale. However, when a Single-item  
department is operated during a sale, it functions the same as an Itemized  
department.  
2. Initial setting is as follows.  
All departments .......Non-taxable & Itemized status  
Sample Programming Operation  
To set the following department status:  
Department 1 ...... Taxable & Single-item  
Department 2 ...... Non-taxable & Itemized  
Department 3 ...... Taxable & Itemized  
Department 4 ...... Non-taxable & Single-item  
-- Print Sample --  
Submode No.  
3 #  
Taxable Status Symbol  
1 1  
0 2  
0 3∗  
1 4  
0003  
00-01  
Department Code  
00-00-00  
Status Code  
0: Itemized  
Key Operation)  
1: Single-item  
3 X/TIME
1
0
0
1
AT/TL  
TAX  
1
2
TAX  
M  
3
4
- 14 -  
EO1-11099  
Time Setting  
AT/TL  
5 X/TIME  
Hour  
Minute  
Submode No.  
(00 to 23) (00 to 59)  
Sample Programming Operation  
To set the time to 13:35 (1:35 p.m):  
Key Operation)  
-- Print Sample --  
5 #  
13-35  
0004  
Time which was  
programmed  
5 X/TIME  
1
3
3
5
AT/TL  
13-35  
00-00-00  
Date Setting  
6 X/TIME  
AT/TL  
Month  
Day  
Year  
Submode No.  
(01 to 12) (01 to 31) (95, 96, etc.)  
NOTE: The date entry order above shows the initial set order. The entry order of Day-  
Month-Year or Year-Month-Day can be selected instead of Month-Day-Year by  
the System Option Setting described in page 12.  
Sample Programming Operation  
To set the date to October 3, 1995:  
Key Operation)  
6
5 X/TIME 1 0  
0
3
9
5
AT/TL  
-- Print Sample --  
6 #  
Date which was  
programmed  
10-03-95  
0005  
13-46  
10-03-95  
- 15 -  
EO1-11099  
Department HALC Setting  
The HALC (High Amount Listing Capacity) is used to check excessively high amounts  
entered by mistake. By setting HALCs, such mistakes will be prevented at the earliest  
stage.  
Repeatable for other department  
AT/TL  
X/TIME  
Dept.  
8
0 to 7; For example, if "3" is entered, it means 3 digits and the  
high amount limit is 999 ($9.99).  
NOTE: Initial setting is as follows.  
All departments..........Price entry up to 7 digits ($99999.99) is allowed.  
Sample Programming Operation  
To set the following department HALCs:  
Department 1 ...... 3 digits  
Department 2 ...... 4 digits  
Department 3 ...... 5 digits  
Department 4 ...... 6 digits  
Key Operation)  
AT/TL  
8 X/TIME  
3
5
6
1
2
3
4
4
-- Print Sample --  
8 #  
Department Code  
3 1  
4 2  
5 3  
6 4  
0006  
14-15  
10-03-95  
HALC which was programmed  
- 16 -  
EO1-11099  
Secret Code Setting  
When this code is set, operations in the "Z" mode will be prohibited without this code  
entry.  
AT/TL  
9
9 X/TIME  
Secret Code: 1 to 9999  
(0 to clear the secret code)  
Sample Programming Operation  
To set a secret code of 2428:  
Key Operation)  
AT/TL  
8
9
9 X/TIME  
2
4
2
-- Print Sample --  
99 #  
2428  
0007  
14-45  
Secret Code which was  
programmed  
10-03-95  
% Rate Setting  
%
Rate: 1 to 99  
(0 to clear the % rate)  
NOTE: Whether the % key is used as the function of %+ or %- is determined by the  
System Option Setting described in page 12.  
Sample Programming Operation  
-- Print Sample --  
"%+" is printed if the  
[%] key is used as the  
[%+] key  
To set 5% on the [%] key:  
#
5 %-  
Key Operation)  
0008  
15-01  
10-03-95  
5
%
% Rate which was  
programmed  
- 17 -  
EO1-11099  
PLU Setting  
Repeatable for other PLU  
AT/TL  
PLU  
Dept.  
PLU Code:  
1 to 100  
Preset Price:  
max. 6 digits  
($9999.99)  
Linked department  
NOTE below  
NOTE: When0isenteredasapresetpriceinabovekeysequence,thepresetpriceof$0.00  
will be programmed.  
Sample Programming Operation  
To set the following PLUs:  
PLU 6 (Preset Price: $1.50, Linked Department: Department 1)  
PLU 24 (Preset Price: $2.50, Linked Department: Department 2)  
PLU 28 (Preset Price: $1.75, Linked Department: Department 3)  
PLU 30 (Preset Price: $2.00, Linked Department: Department 4)  
Key Operation)  
6
1
PLU  
1
5
0
3
2
PLU  
2
8
PLU  
4
2
1
2
2
5
0
AT/TL  
3
4
0
PLU  
0
0
7
5
-- Print Sample --  
PLU Code  
6
1.50 1 @  
24  
2.50 2 @  
28  
Linked Department Code  
Preset Price  
1.75 3 @  
30  
2.00 4 @  
0011  
15-47  
10-03-95  
- 18 -  
EO1-11099  
PLU Deletion  
Repeatable for other PLU to be deleted  
V
D
PLU  
AT/TL  
PLU Code:  
1 to 100  
Sample Programming Operation  
To delete the PLU Code 30 which was programmed in the preceding page:  
Key Operation)  
3 0  
AT/TL  
PLU
V D  
-- Print Sample --  
30  
PLU Code which was  
-----------  
deleted  
0012  
16-07  
10-03-95  
Deletion Symbol  
Amount Format Setting  
This operation determines the Amount Format for display and print.  
AT/TL  
A
1: Amount Format ( 0)  
or  
3: Amount Format (0.00)  
Initial Setting  
Sample Programming Operation  
To set the Amount Format of "  
Key Operation)  
0":  
-- Print Sample --  
AT/TL  
1
0
0013  
16-13  
Amount Format which  
was programmed  
10-03-95  
- 19 -  
EO1-11099  
Tax Table Setting  
TYPE 1: TAX FULL BREAKS (COMBINATION OF NON-CYCLIC AND CYCLIC BREAKS)  
TAX  
(Max. amount non-taxable)  
Max. 4 digits; 0 to 9999 (¢)  
(Max. amount for 1¢ tax levied)  
(Max. amount for 2¢ tax levied)  
TAX  
TAX  
Repeat up to the "A" Break (Non-cyclic Break Limit)  
TAX  
(Max. amount for N¢ tax levied)  
(to indicate the completion of Non-cyclic Breaks)  
ST  
(Max. amount for N+1¢ tax levied; Beginning of Cyclic  
Breaks)  
TAX  
(Max. amount for N+2¢ tax levied)  
T
A
X
Repeat up to the "B" Break ("B" Break - "A" Break = Multiple of $1.00; max.  
$99.00)  
(to complete the Tax Table Setting)  
AT/TL  
NOTE: A maximum of 32 breaks can be programmed for the tax table.  
- 20 -  
EO1-11099  
TYPE 2: TAX % ONLY  
TAX  
AT/TL  
0
ST  
max. 5 digits; 0.001% to 99.999%  
NOTE below  
NOTES: 1. As for a numeric value to be entered, be certain to include down to three  
decimal places. For example, to set 4%, enter "4000".  
2. % Calculation Fraction Rounding Process for Tax is fixed to "Round Off".  
TYPE 3: COMBINATION OF NON-CYCLIC BREAKS AND % RATE  
First, complete the setting of Non-cyclic Breaks as shown in TYPE 1.  
(Tax rate applied when exceeding the Non-cyclic  
Break amount)  
The description for  
the Tax Rate in  
TYPE 2 is also  
applied to this case.  
AT/TL  
- 21 -  
EO1-11099  
Sample Programming Operation  
TYPE 1: TAX FULL BREAKS  
To set the following Tax Break Table:  
Amount Difference  
from Previous Break  
Breaks  
Tax  
$0.01 to $0.10  
$0.11 to $0.21  
$0.22 to $0.35  
0¢  
1¢  
2¢  
$0.10  
$0.11  
Non-cyclic Breaks  
$0.36 to $0.50  
$0.51 to $0.64  
$0.65 to $0.78  
$0.79 to $0.92  
$0.93 to $1.07  
$1.08 to $1.21  
$1.22 to $1.35  
3¢  
4¢  
5¢  
6¢  
7¢  
8¢  
9¢  
$0.14  
$0.15  
$0.14  
$0.14  
$0.14  
$0.15  
$0.14  
One cycle of  
Cyclic Breaks  
Cyclic Breaks  
$1.36 to $1.50  
10¢  
$0.14  
.
.
.
.
.
.
.
.
.
The same cycle  
repeats.  
Key Operation)  
TAX  
1
2
3
0
2
5
-- Print Sample --  
TAX  
#
TAX  
0.10 TX  
0.21 TX  
0.35 TX  
ST  
ST  
0.35  
TAX  
5
6
7
9
0
2
3
0
4
8
2
7
0.50 TX  
0.64 TX  
0.78 TX  
0.92 TX  
1.07 TX  
1.21 TX  
1.35 TX  
TAX  
TAX  
TAX  
TAX  
1
1
1
1.35 TA  
0014  
1
TAX  
16-29  
10-03-95  
TAX
5
AT/TL
- 22 -  
EO1-11099  
TYPE 2: TAX % ONLY  
To apply 15% to any amount:  
-- Print Sample --  
Key Operation)  
#
0 ST  
TAX  
1
5
0
0 0
AT/TL  
0.00 TX  
0.00 ST  
15.000 %  
0016  
16-36  
10-03-95  
TYPE 3: COMBINATION OF NON-CYCLIC BREAKS AND % RATE  
To set the following Tax Break Table:  
Amount Difference  
from Previous Break  
Breaks  
Tax  
$0.01 to $0.10  
$0.11 to $0.22  
$0.23 to $0.39  
$0.40 to $0.56  
$0.57 to $0.73  
$0.74 to $0.90  
$0.91 to $1.08  
0¢  
1¢  
2¢  
3¢  
4¢  
5¢  
6¢  
$0.10  
$0.12  
$0.17  
$0.17  
$0.17  
$0.17  
Non-cyclic Breaks  
% Rate of 6%  
Key Operation)  
TAX  
1
0
2
-- Print Sample --  
TAX  
2
3
5
7
9
0
#
0.10 TX  
9
TAX  
0.22 TX  
0.39 TX  
0.56 TX  
0.73 TX  
0.90 TX  
1.08 TX  
1.08 ST  
6.000 %  
0017  
TAX  
6
3
TAX  
TAX  
0
TAX  
1
8
ST  
16-38  
10-03-95  
AT/TL  
6
0
0
0
- 23 -  
EO1-11099  
10. Verification of Programmed Data  
The set data of the programming operations can be verified by the following operations. A  
receipt is issued for each operation.  
SET  
OFF  
REG  
Mode Select  
X
Switch: X  
Z
To read PLU Tables  
To read Department Status  
ST  
3
2
ST  
X
X
PLU Code  
Taxable Status  
Symbol  
1 1∗  
0 2  
0 3∗  
1 4  
0 5  
0 6  
0 7  
0 8  
6
1.50 1 @  
24  
2.50 2 @  
28  
Linked  
Department Code  
Preset Price  
1.75 3 @  
0022  
16-26  
Department Code  
0021  
16-25  
10-03-95  
10-03-95  
Status Code  
0: Itemized  
1: Single-item  
Toread%Rateandthecontentsof  
the System Option  
To calculate Tax Amount  
Displays the tax  
amount.  
TAX  
4
ST  
Any amount  
X
% Rate  
5 %-  
10213025 #  
0023  
16-27  
10-03-95  
NOTE: Result of the Tax Calculation  
System Option  
Setting  
Test is not printed.  
- 24 -  
EO1-11099  
11. Daily Operation Flow  
The following shows a typical daily operation flow on the register.  
Reference  
Page  
Before Opening the Store...  
Ensure that the register is firmly plugged  
in the wall outlet.  
3
Check to see if sufficient portion of paper  
roll remains.  
9
26, 27  
Check the time, and print condition.  
During Business Hours...  
Opening the store  
27  
35  
Ordinary transaction entries  
Received-on-Account and Paid Out trans-  
actions  
36  
Taking Read (X) Report.  
Closing the store  
After Closing the Store...  
Taking Reset (Z) Report  
36  
39  
Tear off the print portion of Journal Paper  
(if the printer is used for journal record-  
ing).  
Leave the drawer open, and Set the  
Mode Select Switch to OFF.  
40  
40  
Take all the cash from the drawer to the  
office with the journal and Reset (Z) Re-  
port.  
- 25 -  
EO1-11099  
12. Transaction Entries  
If the register is programmed with all requirements, it is ready  
to accept transaction entries. Before starting to enter transac-  
tions, set the Mode Select Switch to the REG position.  
SET  
OFF  
REG  
X
Z
WARNING!  
When opening the cash drawer, be careful not to let the drawer hit any person.  
When an error has occurred...  
When the buzzer sounds continuously and "E" is indicated in the leftmost digit of the display,  
the last operation has caused an error and the keyboard is locked. In that case:  
C
Press the  
key to cancel the error condition and the keyboard is now operable.  
This function of the [C] key is also applied to operations in other Mode Select Switch  
positions.  
If errors occur repeatedly on operating the same key sequence, check the cause of the  
error. The following are possible causes of error:  
The Mode Select Switch position is wrong.  
The numeric value entered exceeds the high amount limit.  
A numeric value has not been entered where required.  
A numeric value has been entered where prohibited.  
The key sequence is wrong, or a wrong key has been pressed.  
The operation is not allowed at the current timing.  
Displaying the Time  
The time can be displayed on the register any time when the register is outside a sale.  
X/TIME  
........... Displays the current time.  
hour  
minute  
The time display will disappear when any key excluding the [FEED] key is pressed on the  
keyboard or the Mode Select Switch position is changed.  
- 26 -  
EO1-11099  
No-sale  
The No-sale transaction is used to open the drawer without relating to a sale, for  
such purposes of money exchanges, checking the print condition on the paper roll,  
etc.  
NS/PO  
The drawer opens.  
NS  
No-sale Symbol  
Department  
Code  
Sale Item Entries (Department Entries)  
Price  
1) Entry of One Item  
Dept.  
2.50 2  
Price  
NOTE: The Price entry is possible up to 7 digits. However, it is limited by the  
Department HALC (High Amount Listing Capacity).  
2) Repeat Entry  
Dept. Dept.  
2.50 2  
2.50 2  
Same Department Key  
Price  
NOTE: Depress again the Department key that has been depressed for one  
item entry. The item entry will be repeated as many times as the key is  
depressed.  
3) Quantity Extension (Multiplication)  
X/TIME  
Dept.  
Quantity (max. 3 digits)  
Unit Price  
Quantity  
3 X  
2.50 @  
7.50 2  
Unit Price  
Product  
NOTE: The product (obtained by multiplication) must not exceed 7 digits.  
- 27 -  
EO1-11099  
4) Single-item Department  
Dept. Item, Taxable  
Symbol  
If a Department Key is programmed with  
Single-item status, any entry through the  
key will immediately finalize the sale as  
cash without operating any media key.  
1.50 1  
0.09 TX  
1.59 CA  
0052  
Tax  
Cash Total  
15-10  
10-03-95  
The operation is the same as ordinary  
itemized Department keys already  
described (Entry of One Item, Quantity  
Extension), except that Repeat Entry is  
not possible using  
Department key.  
a
Single-item  
5) Tax Modification (applicable to Add-on Tax Feature)  
Each department is programmed with its own Tax status (Non-taxable, or  
Taxable ). To reverse the Tax status (from taxable to non-taxable, or vice  
versa), depress the following key before or during the required department item  
entry (before the Department Key, at the latest). (Refer to Entry of One Item,  
Repeat Entry, Quantity Extension.)  
TAX  
... to reverse Tax status  
NOTES: 1. The tax-modified status declared by the Tax Modifier key will be  
held until another item is entered. The modified status is held  
even when the item is repeated.  
2. When a Department item is tax-modified and repeated and the  
same item (with the same price and department) must still be  
entered consecutively within a sale with the original tax status  
regained, depress the [C] key before entering original tax-status  
item.  
Linked Department  
Code  
Sale Item Entries (PLU Entries)  
1) Entry of One Item  
Preset Price  
PLU  
PLU Code; 1 to 100  
1.75 3*  
2) Repeat Entry  
PLU PLU  
1.75 3*  
1.75 3*  
Same PLU Key  
PLU Code; 1 to 100  
NOTE: Depress again the PLU key that has been depressed for one item entry.  
The item entry wil be repeated as many times as the key is depressed.  
- 28 -  
EO1-11099  
3) Quantity Extension (Multiplication)  
X/TIME  
PLU  
Quantity (max. 3 digits)  
PLU Code; 1 to 100  
Quantity  
4 X  
1.75 @  
7.00 3∗  
Preset Price  
Product  
NOTE: The product (obtained by multiplication) must not exceed 7 digits.  
4) Single-item PLU  
If a PLU is linked to a Department  
with Single-item status, the entry  
of this PLU will immediately final-  
ize the sale as cash without oper-  
ating any media key.  
Preset Price, Linked  
Dept. Code, Taxable  
Symbol  
1.50 1∗  
0.09 TX  
1.59 CA  
0056  
Tax  
Cash Total  
The operation is the same as  
ordinary itemized PLU already  
described (Entry of One Item,  
Quantity Extension), except that  
Repeat Entry is not possible using  
a Single-item PLU.  
15-26  
10-03-95  
5) Tax Modification (applicable to Add-on Tax Feature)  
Tax status (Non-taxable, or Taxable) for each PLU is determined by that of the  
linked Department. To reverse the Tax status (from taxable to non-taxable, or  
vice versa), depress the following key before or during the required PLU item  
entry (before the PLU Entry, at the latest). (Refer to Entry of One Item, Repeat  
Entry, Quantity Extension.)  
TAX ... to reverse Tax status  
NOTES: 1. The tax-modified status declared by the Tax Modifier key will be  
held until another item is entered. The modified status is held  
even when the item is repeated.  
2. WhenaPLUitemistax-modifiedandrepeatedandthesameitem  
must still be entered consecutively within a sale with the original  
tax status regained, depress the [C] key before entering original  
tax-status item.  
- 29 -  
EO1-11099  
Dollar Discount  
1) Dollar Discount on a Department Item or a PLU Item  
Department or PLU Entry  
-
Discount Amount  
2) Dollar Discount on Subtotal  
Sale Item Entries  
-
ST  
Discount Amount  
Subtotal  
Dollar Discount of  
$1.50  
8.00 ST  
-1.50  
NOTE: The discount amount must not exceed the item amount or the subtotal  
unless the "Credit Balance" option is selected.  
Percent Discount or Percent Charge  
The [%] key can be programmed to function Percent Discount or Percent Charge.  
1) Percent Discount/Charge on a Department Item or a PLU Item  
(to activate the preset rate)  
Department or PLU Entry  
%
(to activate a manual rate)  
%
Manual Rate; max. 2 digits  
1 (1%) to 99 (99%)  
2) Percent Discount/Charge on Subtotal  
(to activate the preset rate)  
Sale Item Entries  
ST  
%
(to activate a manual rate)  
%
Manual Rate; max. 2 digits  
1 (1%) to 99 (99%)  
NOTE: When a Manual Rate is  
entered, the preset rate is  
disregarded.  
2.00 2  
5 %-  
-0.10  
5%  
Discount  
- 30 -  
EO1-11099  
Void  
Sale items once entered within the current sale can be voided.  
1) Last Line Voiding  
When the last line item (that has just been entered within the current transac-  
tion) is a Department item, a PLU item, Dollar Discount item, or Percent  
Discount/Charge item, it can be voided by simply pressing the [VD] key.  
Department or PLU Entry  
Dollar Discount  
VD  
Percent Discount/Charge  
2.00 2  
2.00 2VD  
Voided  
2) Designated Line Voiding  
When a Department or a PLU item entered before the last item is canceled  
before the sale is finalized, it can be voided. To operate it, follow the ordinary  
Department or PLU entry procedure (Entry of One Item, Quantity Extension)  
except that the [VD] key is depressed just before the Department or PLU key  
depression.  
Example)  
1
2
1
0
0
0
0 Dept.1  
0 Dept.2  
2.00 2  
1.00 1∗  
2.00 2RF  
Voided  
0
Dept.1  
VD
Returned Merchandise  
TheReturnedMerchandisetransactionisusedtorefundmoneytoacustomerwho  
has returned items already purchased. This operation must be performed outside  
a sale only.  
Entry of sale item (Department or PLU) to be returned  
(Entry of One Item, Quantity Extension)  
VD  
3.00 1RF Returned item  
-0.18 TX  
-3.18 CA  
Cash to be returned  
- 31 -  
EO1-11099  
Non-add Number Print  
This function is to print any code number for future reference, such as Customer  
No., Credit Card No., House Charge Account No., etc. Non-add numbers can be  
entered at the starting of a sale or during a sale if the sale is not finalized. Multiple  
non-add numbers can be entered in a sale.  
#/RA  
1234567 # Non-add Number  
Non-add Number; max. 7 digits  
Subtotal Read and Print  
To read the total of the current sale by the customer's request or the operator's  
requirement, simply depress the [ST] key.  
Displays the subtotal (sale total including taxes up to the  
moment).  
Sale Item Entries  
ST  
NOTE: The subtotal amount to be printed is  
11.50 ST  
the pre-taxed sale total.  
Finalizing a Sale  
1) Cash Total  
Sale Item Entries  
ST  
AT/TL  
(
)
5.00  
0.18  
5.18  
Subtotal  
Tax  
Cash Sale Total  
ST  
TX  
CA  
0060  
16-00  
10-03-95  
2) Cash Tender  
Sale Item Entries  
ST  
AT/TL  
(
)
Cash Tendered Amount  
5.00 ST  
Subtotal  
0.18 TX  
5.18 NT  
6.00 AT  
0.82 CG  
0063  
Tax  
Sale Total including Tax  
Cash tendered  
Change due  
16-10  
10-03-95  
NOTE: The sale is finalized as in the sample receipt above when the tendered  
amount is equal to or larger than the sale total (including taxes). When the  
tendered amount is smaller than the sale total (short-tendered), the  
balance due is displayed and the sale is not finalized. In such cases, refer  
to "6) Multi-tender" and "7) Split Tender" on the page 34.  
- 32 -  
EO1-11099  
3) Charge or Credit Total  
Sale Item Entries  
ST  
CH  
)
(
5.00  
0.18  
5.18  
Subtotal  
Tax  
Charge or Credit  
Sale Total  
ST  
TX  
CH  
0064  
16-11  
10-03-95  
4) Check Total  
Sale Item Entries  
ST  
CHK  
(
)
5.00 ST  
0.18 TX  
5.18 CK  
0067  
Subtotal  
Tax  
Check Sale Total  
16-15  
10-03-95  
5) Check Tender  
Sale Item Entries  
ST  
CHK  
(
)
Check Tendered Amount  
5.00 ST  
Subtotal  
0.18 TX  
5.18 NT  
10.00 CK  
4.82 CG  
0068  
Tax  
Sale Total including tax  
Check tendered  
Change due  
16-20  
10-03-95  
NOTE: The System Option Setting allows you to select the following functions of  
the [CHK] key.  
Total & Tender functions  
Total function only  
Tender function only  
- 33 -  
EO1-11099  
6) Multi-tender  
Sale Item Entries  
ST  
AT/TL  
CHK  
or  
(
)
(
)
)
Cash (or Check) Tendered  
Amount less than the sale total  
AT/TL or CHK  
(
Cash (or Check) Tendered Amount  
equal to or larger than the sale total  
5.00 ST  
0.18 TX  
Subtotal  
Tax  
Sale Total including tax  
5.18 TA  
3.00 AT  
5.00 AT  
2.82 CG  
0069  
Cash tendered (short-tendered)  
Cash tendered (over-tendered)  
Change due  
16-23  
10-03-95  
7) Split Tender  
Sale Item Entries  
ST  
AT/TL  
(
)
Cash Tendered Amount  
less than the sale total  
CHK  
CH  
Check Tendered Amount less than  
the sale total-cash tendered amount  
15.00 ST  
0.90 TX  
15.90 TA  
3.00 AT  
5.00 CK  
7.90 CH  
0070  
Subtotal  
Tax  
Sale Total including tax  
Cash tendered (short-tendered)  
Check tendered (short-tendered)  
Charge or Credit Total  
16-25  
10-03-95  
NOTES: 1. A maximum of 7 digits can be entered as Tendered Amount (up to  
$99999.99).  
2. Whenthesaletotaliszeroornegative, thesalecanonlybefinalized  
by Cash Total function.  
- 34 -  
EO1-11099  
Tax Exemption  
The Tax Exemption transaction is used to exempt all taxes from the sale total.  
Sale Item Entries  
Finalizing a sale  
ST  
M  
TAX  
)
(
Sale item Entries with  
Taxable Status  
5.00 3∗  
1.75 3∗  
6.75 ST  
6.75 CA  
Cash Sale Total  
without Tax  
The following operations require the X position of the Mode Select Switch.  
SET  
OFF  
REG  
X
Z
Received-on-Account Payment  
(Mode Select Switch: X)  
The Received-on-Account transaction is used to identify money which is in the  
drawer but not due to business. For example, a customer pays for a sale finalized  
as house charge on a past day, or the operator records the change reserve in the  
drawer loaded from the store office. This operation must be performed outside a  
sale only.  
The drawer opens to enable money entry into the drawer.  
#/RA  
Payment Amount Received;  
max. 7 digits (up to $99999.99)  
10.00 RA  
Paid Out  
(Mode Select Switch: X)  
The Paid Out transaction is used when an amount of money is removed from the  
drawerwithoutrelatingtoasale,forthepurposeofpayingtoawholesaler,etc. This  
operation must be performed outside a sale only.  
The drawer opens to enable paying out.  
NS/PO  
Amount to be paid out;  
max. 7 digits (up to $99999.99)  
12.00  
PO  
- 35 -  
EO1-11099  
13. Read (X) and Reset (Z) Reports  
This Chapter describes the operation to take Read and Reset reports and their print  
formats.  
Before Taking Reports...  
The Read (X) Report allows to read the totals but not clear the memory, while the  
Reset (Z) Report allows to read the totals and, at the same time, clear all the  
resettable totals when the report has been issued.  
The symbol "X" is printed at the top right of a Read Report, while "Z" is printed on  
a Reset Report to indicate the type of report. The contents of the two types of  
reports are the same if both are taken at the same time.  
WARNING!  
When opening the cash drawer, be careful not to let the drawer hit any person.  
OPERATION  
Read (X) Report  
SET  
OFF  
Financial Read (X) Report:  
(The drawer opens.)  
REG  
AT/TL  
X
Z
Cash-in-drawer Read (X) Report:  
(The drawer opens.)  
#/RA  
PLU Read (X) Report:  
(The drawer opens.)  
PLU  
Reset (Z) Report  
SET  
OFF  
REG  
Financial Reset (Z) Report:  
(The drawer opens.)  
AT/TL  
(
)
X
Z
Secret code if  
programmed  
PLU Reset (Z) Report:  
(The drawer opens.)  
PLU  
(
)
Secret code if  
programmed  
- 36 -  
EO1-11099  
Memory Balance  
Grand Total = (Sum of Gross Sale)  
Gross Sale = (Depts. Total) + (Tax Amount) + (Returned Merchandise & Desig-  
nated Line Voiding) + (Last Line Voiding) + (%+)  
NOTE 1  
NOTE 2  
Net Sale with Tax = (Depts. Total) + (Tax Amount) + (%+)  
NOTE 2  
Media Total = (Cash Sales) + (Check Sales) + (Charge Sales)  
= (Net Sale with Tax) - (%-) - (Dollar Discount)  
NOTE 3  
Customer Total = (Cash Sales Customer) + (Check Sales Customer) + (Charge  
Sales Customer)  
Returned Merchandise & Designated Line Voiding  
= (Returned Merchandise & Designated Line Voiding) +  
(Negative Tax Amount)  
NOTE 4  
NOTES: 1. Thevoidtransactionof%-andDollarDiscountisnotprocessedtothe  
Void Memory. However, the void transaction of %+ is processed to  
its memory.  
2. In case that the [%] key is used as the [%+] key.  
3. In case that the [%] key is used as the [%-] key.  
4. "Negative Tax Amount" means a tax amount to be returned to a  
customer with an amount of a returned item.  
- 37 -  
EO1-11099  
Report Sample Format  
Financial Report  
Cash-in-drawer Report  
Reset Report Symbol  
("X" for Read Report)  
Z
X
Grand Total (non-resettable)  
Gross Sale: Item Count  
Amount  
Dept. 1 Sale: Item Count  
Amount  
257.06 #  
28  
52.76  
0090  
19-05  
Cash-in-drawer  
Amount  
TA  
83.06  
4 1  
8.20  
7 2  
29.00  
2 3  
3.50  
2 4  
3.20  
2 5  
5.50  
5 6  
16.30  
2 7  
4.80  
1 8  
1.00  
10-03-95  
PLU Report  
Z
6
3
4.50  
24  
PLU Code 6  
Sales:Count  
Amount  
4
Dept. 8 Sales: Item Count  
Amount  
10.00  
28  
Tax Total  
1.96 TX  
7
Net Sale with Tax: Item Count  
Amount  
%- Count  
Amount  
Dollar Discount  
Amount  
Total Customer Count  
Media Total  
Cash Sales:Customer Count  
Amount  
Check Sales: Customer Count  
Amount  
25  
12.25  
30  
1
2.00  
0002 Z  
0092  
19-10  
73.46 NS  
1
0.90  
4
6.50  
16  
66.06  
12  
34.75  
1
5.41  
3
25.90  
3
32.60  
1
PLU Code 30  
Sales:Count  
Amount  
%-  
Reset Counter  
-
NT  
CA  
CK  
CH  
RA  
10-03-95  
Charge or Credit Sales: Customer Count  
Amount  
Received-on-account Count  
Amount  
Paid Out Count  
10.00  
52.76  
10.00  
1
3.60  
2
Amount  
PO  
TA  
CK  
Cash-in-drawer Amount  
Check-in-drawer Amount  
Last Line Voiding Count  
Amount  
Returned Merchandise & Designated  
Line Voiding: Item Count, Amount  
Reset Counter  
Consecutive No.  
Time  
Date  
VD  
6.00  
0003  
0096  
19-20  
10-03-95  
RF  
Z
- 38 -  
EO1-11099  
14. Maintenance  
WARNING!  
Care must be taken not to injure yourself with the paper cutter.  
Replacing the Paper Roll  
1
To remove the Printer Cover, insert the  
Printer Cover/Drawer key to the Printer  
CoverLock, andthenturnit90° clockwise.  
2
If the printer is used for Journal, hold down  
the [FEED] key to wind up the printed  
portion of paper, then cut the paper as  
shown in the figure. Hold down the  
[FEED] key again to advance the remain-  
ing paper end.  
If the printer is used for Receipt, cut the  
paper roll as shown in the figure. Then  
hold down the [FEED] key to advance the  
remaining paper end.  
The wound-up portion of the paper (when  
used for Journal) can easily be removed  
from the Reel by pulling it sideways.  
3
Set the paper roll ready for print. Refer to  
Chapter "8. Installing the Paper Roll".  
- 39 -  
EO1-11099  
Replacing the Ink Roller  
1
2
To remove the Printer Cover, insert the  
Printer Cover/Drawer key to the Printer  
CoverLock, andthenturnit90° clockwise.  
Pinch the Ink Roller Knob with your fin-  
gers, and pull it upward.  
3
Insert the new Ink Roller in the slot of the  
carriage by pushing it all the way in until it  
is firmly settled with a "click" sound.  
Manual Drawer Release  
The drawer will automatically open on appropri-  
ate operations. However, in the event of a  
power failure, etc., the drawer can be released  
manually.  
First, insert the Printer Cover/Drawer Key to the  
Drawer Key Lock, then turn it 90° counter-  
clockwise.  
Next, push the Drawer Release Lever located  
on the bottom side of the register in the direction  
of the arrow, and the drawer opens.  
- 40 -  
EO1-11099  
Removing the Drawer  
Pull out the drawer all the way until it hits the  
stopper. Thenliftupthedrawerandpullitagain.  
WARNING!  
When opening the cash drawer, be careful not to let the drawer hit any person.  
Battery Exchange  
WARNING: Be certain to replace batteries with new ones  
every year. If they run down, the programmed  
data and sales data will all be cleared.  
1
To exchange batteries, please keep the power  
cordoftheregisterconnectedtothewalloutlet.  
If the batteries are removed with the power  
cord disconnected, the programmed data and  
sales data will all be cleared.  
2
To remove the Printer Cover, insert the  
PrinterCover/DrawerkeytothePrinterCover  
Lock, and then turn it 90° clockwise.  
3
Remove the Battery Cover.  
- 41 -  
EO1-11099  
4
5
Replace the old batteries with new ones,  
while confirming that the positive (+) and  
negative (-) ends face the proper directions.  
(Batteries: SUM-3 1.5V x 3 pieces)  
NOTE: Do not mix used and new batteries in  
the battery compartment.  
ReturntheitemremovedinStep3,andattach  
the Printer Cover.  
15. Specifications  
Size ................................... 350 mm (width) x 400 mm (depth) x 250.8 mm  
(height including rubber feet)  
Weight ............................... 4.76 kg  
Power Required ................ 117V±10%, 60Hz  
Power Consumed.............. 0.08A  
Operating Temperature..... 0°C to 40°C  
Operating Humidity ........... 10% to 90% RH  
Size of Paper Roll ............. 57.5±0.5mm (width) x max. 80mm (diameter),  
0.06 to 0.085mm (thickness)  
Memory Protection ............ Dry Battery SUM-3 1.5 V x 3 pieces;  
Life of about 1 year  
(Be certain to replace batteries with new ones every  
year.)  
Handling the Batteries  
When inserting batteries, place them so that the positive (+) and negative  
(-) ends face the proper directions as shown in the battery compartment.  
Do not mix used and new batteries in the battery compartment. Replace all  
batteries at the same time.  
Do not leave discharged batteries in the battery compartment. Leakage  
from such batteries may damage the register.  
Do not dispose the batteries in a fire. If put in a fire, they may explode.  
Specifications are subject to change without notice.  
- 42 -  
Toshiba TEC Corporation  

Tektronix Car Amplifier 5A48 User Manual
Star Manufacturing 3SP User Manual
Sony XS W1621 User Manual
Sony Cyber shot DSCTX200VV User Manual
Sony CDX GT310 User Manual
Sharp EL 9400 User Manual
Sanyo VPC CG9bk User Manual
Samsung SVL 2812 User Manual
Samsung SCD86 User Manual
Samsung NX100 User Manual