Taylor AB 1000 BL User Manual

by  
Blender &  
Smoothie Dispenser  
Instruction Manual  
Item # AB-1000-BL 120V ~ 60Hz 500W  
IMPORTANT SAFEGUARDS  
When using electrical appliances, basic safety precautions should always be followed, in-  
cluding the following:  
1. READ ALL INSTRUCTIONS COMPLETELY BEFORE USING.  
2. To protect against electrical shock do not immerse or rinse cord, plugs or this appli-  
ance in water or any other liquid.  
3. Close supervision is necessary when any appliance is used by or near children.  
4. Unplug from outlet when not in use, before putting on or taking off parts and before  
cleaning.  
5. Avoid all contact with moving parts. Keep hands and utensils out of the container  
while blending to reduce the risk of severe injury to persons or damage to the  
blender. A scraper may be used, but must be used only when the blender is not run-  
ning.  
6. Do not operate any appliance with a damaged cord or plug or after the appliance mal-  
functions, or is dropped or has been damaged in any manner. Return the appliance to  
Taylor® (see warranty) for examination, repair or adjustment.  
7. Do not use attachments that are not supplied for this appliance from Taylor®. The use  
of attachments, including canning jars, is not recommended by Taylor and may cause a  
risk of injury to persons, or permanently damage this product.  
8. Do not use outdoors.  
9. Do not let cord hang over edge of table or counter, or touch hot surfaces including  
the stove.  
10. Blades are sharp; handle very carefully especially when cleaning inside the blending  
jar.  
11. Always operate the blender with the cover in place. Do not attempt to remove the  
cover until blades have come to a complete stop.  
12. When blending hot liquids, remove the center piece, (Filler Cap) of the two-piece  
cover.  
13. Do not feed food into the running blender by hand; use a utensil.  
14. Make sure the motor stops completely and the electrical cord is unplugged before dis-  
assembling or cleaning.  
15. Ensure the unit is completely assembled before using.  
16. To disconnect, be sure the unit is off, then remove the plug from the wall outlet by  
grasping the plug and pulling. Never unplug the appliance by pulling on the cord.  
17. When using this appliance, provide adequate air space above and on all sides for air  
circulation.  
18. Do not place this appliance near a hot gas or electric burner or in an oven.  
19. Do not leave the appliance unattended during use.  
20. Do not use this appliance for other than its intended use.  
21. Do not attempt to defeat the covers interlock mechanism as serious injury may result.  
22. Do not use a broken, chipped or cracked blending jar or cutting blade.  
23. Do not place the blending jar in the freezer filled with food or liquid. It will freeze  
and can result in damage to the blades, jar, and blender unit and possibly result in per-  
sonal injury.  
SAVETHESE INSTRUCTIONS  
3
SPECIAL INSTRUCTIONS  
This appliance is for HOUSEHOLD USE ONLY.  
This appliance has a polarized plug (one blade is wider than the other). To re-  
duce the risk of electrical shock, this plug will fit in a polarized outlet only  
one way. If the plug does not fit fully in the outlet, reverse the plug. If it still  
does not fit, contact a qualified electrician. Do not modify the plug in any  
way.  
Make sure the voltage in your outlet is the same as the voltage indicated on  
the appliance. For 120 –Volt AC electrical outlet only.  
The length of the cord used on this appliance was selected to reduce the haz-  
ards of becoming tangled in, or tripping over a long cord. For safety, it is not  
recommended to use an electrical extension cord with this appliance.  
Do not immerse or rinse base of unit, plug or cord in water or other liquids.  
Use with wall receptacle only.  
Do not attempt to service this unit yourself.  
SAFETY SYSTEM  
This appliance is provided with a safety system which disables the mechanism if  
the jar or the lid is not properly fitted even if the rotary control knob is at the ON  
position.  
Note: Do not use the jar or the lid to switch the appliance on and off.  
If the cutting blades lock and do not move, it will damage the motor. Do not use,  
call Customer Service for information.  
INTRODUCTION  
Now you can learn how to prepare and enjoy great tasting, healthy meals and  
snacks in minutes using your The Biggest Loser™ Blender & Smoothie Dispenser  
by Taylor®. You will learn how to make the delicious and easy recipes that cut out  
calories, but leave in all the taste. The appliance and recipes are great tools to get  
you on track. There are over 125 more healthy and delicious recipes that you can  
find in the Biggest Loser Cookbook. When you start eating right, you may feel  
better, have more energy and feel empowered. For more information on NBCs  
The Biggest Loser, or to join The Biggest Loser Club, please visit the official  
Biggest Loser web site at www.nbc.com/The_Biggest_Loser.com or  
www.biggestloserclub.com  
4
DESCRIPTIVE DIAGRAM  
1. Filler Cap  
2. Lid  
1
3. Blending Jar  
4. Dispenser  
5. Shield  
6. Base  
7. Rotary Control  
Knob  
2
3
8. Dispenser Lever  
9. Drip Tray  
4
5
8
6
7
9
5
USING YOUR BLENDER & SMOOTHIE DISPENSER  
BEFORE FIRST USE  
Make sure the voltage in your outlet is the same as the voltage indicated on  
the appliance. This product is for 120 –Volt AC electrical outlet only.  
The Blender & Smoothie Dispenser is equipped with a safety locking system  
to increase security during operation. The blending function will not work if  
the jar, blades and cover are not properly locked in place.  
Remove any bags, labels or stickers from the appliance.  
Clean the base unit with a damp soft cloth.  
Wash all of the removable parts – jar, lid, filler cap, dispenser, dispenser lever  
and drip tray using a sponge, warm water and mild dish detergent. Rinse and  
dry carefully.  
NOTE: do not immerse the base unit in water when cleaning.  
HOW TO USE YOUR BLENDER & SMOOTHIE DISPENSER  
Place the unit on a flat, dry, sturdy surface. This appliance is not for use in  
convection, or conventional ovens, microwaves, or on stovetop.  
Wash and dry all components thoroughly as stated above.  
Assemble blender components. Always be sure that the appliance is properly  
assembled before using. Blades are extremely sharp; never touch the cutting  
edge of blades.  
Make sure the rotary control knob is at the “0” position. Plug the cord into  
AC wall outlet.  
Pull the drip tray to the extended position.  
Place jar onto the base.  
Add ingredients to the jar as directed by your recipe.  
Add ingredients to the blender a little at a time to ensure proper blending and  
to prevent overflow. Never fill container more than ¾ full; the action of the  
blade will cause ingredients to rise in the container. Make larger recipes in  
multiple batches.  
Unless the recipe states differently, pour liquid ingredients into the blender be-  
fore solid ingredients. Adding the liquid first will reduce blending time.  
Always add 1 cup of liquid before processing ice.  
Place the lid with the filler cap in position onto the jar. Remember; always  
hold the handle during blending.  
Turn the rotary control knob to the desired speed for blending.  
After finished blending, turn off by turning the rotary control knob to the “0”  
position.  
Always turn blender off and wait until blades have stopped  
rotating before removing jar.  
6
HOW TO USE THE DISPENSING FEATURE  
A) Press the drinking cup against dispenser lever. Dispensing will automatically  
stop when the cup is removed.  
OR  
B) Press down on the knob of the dispenser lever with your finger. Dispensing  
will automatically stop when it is released.  
To dispense thicker liquids, such as smoothies, milkshakes, frozen drinks, etc.,  
turn blender ON and then dispense. Turn OFF after you are done dispensing.  
B
A
7
BLENDING GUIDE  
Blending Speeds:  
P= Pulse  
0 = Off  
1 = Low  
2 = Medium  
3 = High  
1. General:  
-
-
-
Make sure the blending jar and lid with filler cap are in proper position.  
Blend for 5 to 30 seconds and check consistency. Continue blending until the  
desired consistency is reached. Over-blending will result in loose consistency.  
Keep hands and utensils out of the jar while blending to prevent serious injury.  
A scraper may be used, but must only be used when the blender is not run-  
ning.  
Do not try to mash potatoes, mix stiff dough, whip egg whites, grind raw  
meat or extract juice from fruits and vegetables. This blender is not made to  
perform these tasks.  
2. Solids:  
-
-
Thick mixtures may require special attention during blending. Periodically  
turn off the unit and scrape the mixture off of sides of blending jar inward to-  
ward the blade. Replace the lid and continue blending. Select a higher speed  
if blending becomes sluggish.  
When the filler cap is removed, you can add solid ingredients a little at a time  
through the hole in the blender lid. Always cut solid foods such as vegetables  
and cheeses into small chunks (about ¾” to 1” long) before placing in the  
blending jar.  
3. Hot Ingredients:  
-
Processing hot foods or liquids in the blender may cause hot liquid to spurt  
out when the lid is removed. Always remove the filler cap from the lid before  
blending hot foods or liquids to vent steam. Keep hands and other exposed  
skin away from the lid opening to reduce possible risk of steam burns.  
4.Crushing Ice:  
-
Fill blending jar 1/3 full of cold water. Add about 2 cups (500ml) of ice cubes.  
Lock filler cap into lid and lock lid on the blending jar. Turn rotary control  
knob to speed “3”. Continue until ice is crushed to desired consistency. Pour  
contents into colander to drain off water.  
DO NOT CRUSH ICE WITHOUT LIQUID. Failure to follow these direc-  
tions can result in damage to the blades, jar and possibly result in personal in-  
jury.  
8
CLEANING AND MAINTAINENCE  
After each use and before cleaning, allow the unit to stop and unplug the appli-  
ance from outlet. DO NOT ATTEMPT TO CLEAN WHILE THE  
MOTOR IS RUNNING OR THE COMPONENTS ARE STILL MOV-  
ING. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT  
IN SERIOUS INJURY OR ELECTRICAL SHOCK.  
CAUTION: NEVER IMMERSE THE BASE UNIT, CORD OR  
PLUG IN WATER OR OTHER LIQUIDS.  
To clean the base, rotary control knob and cord, wipe clean with a damp  
sponge or cloth and dry immediately. Never use excess water, treated cloths,  
harsh cleaning agents, or sprays.  
Remove blender jar, dispenser, dispenser lever, drip tray, lid and filler cap. It is  
recommended to wash the components immediately after each use in warm,  
soapy water. Rinse and dry thoroughly. Jar blades are extremely sharp. Wash  
blades carefully and avoid direct contact with the blades themselves.  
To remove the dispenser lever, please follow the steps below:  
1. Pull up shield.  
2. Press against dispenser lever as shown.  
3. Lift up the dispenser lever.  
4. Move the dispenser lever forward and out.  
1
3
2
4
DO NOT FORCIBLY PULL ON THE DISPENSER LEVER, AS  
DAMAGE WILL RESULT.  
9
To remove the dispenser from the jar, please follow the steps below:  
1. Turn the jar on an angle so you can grasp the dispenser easily.  
2. Turn the dispenser to the unlock position (toward the unlocked padlock pic-  
ture).  
3. Pull out as shown. Do not force the dispenser.  
1
2
To reassemble, reverse the above procedures and make sure the dispenser is  
locked in place before blending again.The small arrow on the dispenser front  
will line up with the small arrow on the jar bottom where the locked padlock  
picture is shown. If the dispenser is not properly locked in place, ingredients  
will leak from the drain hole in the bottom of the jar.  
Reassemble all parts and store in a dry place, unplugged and away from the  
reach of children. Personal injury can result if the blender is turned on when  
not properly assembled.  
10  
TROUBLESHOOTING  
The Blender & Smoothie Dispenser will not operate.  
Has a household fuse blown, or has a circuit breaker tripped?  
Is the power supply cord properly seated in the unit and the outlet?  
Is the inter-locking jar and lid secured properly?  
Has the cord been damaged in some way? If so, DO NOT USE THE APPLI-  
ANCE. Contact Customer Service for replacement information.  
Has the safety shut off feature activated due to improper lid closure?  
Blender & Smoothie Dispenser is vibrating.  
Are the components securely positioned in the base? If not, turn off the unit  
and reposition the components onto the unit base.  
Has the appliance been overloaded? Attempting to blend large quantities or  
large pieces of food may cause vibration. See section titled “How to use your  
Blender & Smoothie Dispenser” or BLENDING GUIDE.  
The lid will not seat properly.  
Is the product assembled properly?  
Is there food blocking the lid? If so, the jar is overloaded. Remove half of the  
ingredients and blend in two smaller batches.  
Blended result is too watery.  
The food or beverage is over processed. Use brief pulses, use a lower speed or  
blend for less time.  
Food is collecting on the sides of the jar.  
You may be blending too much ingredients at one time. Turn machine off.  
When the blade stops completely, remove cover and clean with a spatula, turn-  
ing ingredients inward toward the blade. Add additional liquid if necessary. If  
there is still a problem, remove half of the ingredients and blend in two smaller  
batches.  
11  
WARRANTY  
Taylor® warrants this product to be free from defects in material or workmanship  
for one (1) year for the original purchaser from date of retail purchase. It does not  
cover damages or wear resulting from accident, misuse, abuse, commercial use, or  
unauthorized adjustment and/or repair. If service is required, do not return to re-  
tailer. Should this product require service (or replacement at our option), please  
contact Taylor Customer Service at 1-800-289-0944.  
There are no expressed warranties except as listed above.This warranty gives you  
specific legal rights, and you may have other rights which vary from state to state.  
If you need replacement parts:  
Use only Taylor specified parts. These specified parts will fit right and work  
right because they are made with the same precision used to build every new  
Taylor appliance.  
Keep this book and your sales receipt together for future reference. You must pro-  
vide proof of purchase for warranty purposes.  
For additional product information, or warranty information in Canada or else-  
where outside the USA, please contact us through www.taylorusa.com  
Taylor® is a registered trademark of Taylor Precision Products and its affiliated  
companies.All rights reserved.  
Made to our exact specifications in China.  
www.taylorusa.com  
© 2008 The Biggest Loser is a registered trademark and copyright of NBC Stu-  
dios, Inc. & Reveille LLC.All Rights Reserved.  
AB-1000-BL 9.08  
12  

Westcott 1040 User Manual
Toshiba Camcorder CS3330BI User Manual
Taylor AM 1700 BL User Manual
Sony ILCE7SB User Manual
Sony HDRAX2000H User Manual
Sony DCR TRV70 User Manual
Sony DCR TRV8 User Manual
Sony 500WSPL User Manual
Sharp UP 820F User Manual
Sanyo Camcorder VPC HD2000EX User Manual