T Fal BeerTender User Manual

Couverture B80 oneway seb.qxd:Couverture B80 oneway seb.qxd 23/06/08 11:09 Page 1  
0828 074  
B80 one way T-FAL US modif heineken .qxd:B80 one way SEB Uklta.qxd 25/06/08 15:10 Page 4  
1 - IMPORTANT  
SAFEGUARDS  
When using electrical appliances, basic safety  
precautions should always be followed to reduce the  
risk of fire, electric shock, and/or injury to persons  
including the following :  
1. Read all instructions.  
2. To protect against fire, electric shock and injury  
to persons, do not place cord, plugs or  
appliance in water or other liquid.  
3. Close supervision is necessary when any  
appliance is used near children. Keep appliance  
out of reach of children. Product not intended  
for use by children.  
4. Unplug from outlet when not in use and before  
cleaning. Allow to cool before putting on or  
taking off parts, and before cleaning the rest  
of the appliance.  
5. Do not operate any appliance with a damaged  
cord or plug or after the appliance malfunctions,  
or has been damaged in any manner. Return  
appliance to your nearest authorized T-fal  
Service Center for examination, repair or  
adjustment (see Limited Warranty).  
6. The use of an accessory not evaluated for use  
with this appliance by T-fal may result in fire,  
electric shock or injury to persons.  
7. Do not use outdoors.  
8. Do not let cord hang over edge of table or  
counter, or touch hot surfaces.  
9. Do not place on or near a hot gas or electric  
burner, or in a heated oven.  
10. To disconnect, turn the control to «off» then  
remove plug from wall outlet.  
11. Do not use appliance for other than intended  
use.  
12. Appliance for household indoor use only.  
13. Do not immerse in water.  
SAVE THESE INSTRUCTIONS  
4
B80 one way T-FAL US modif heineken .qxd:B80 one way SEB Uklta.qxd 25/06/08 15:10 Page 5  
CAUTION  
This appliance is for household use only. Any  
servicing other than cleaning and user maintenance  
should be performed by an authorized service  
representative.  
To reduce the risk of fire or electric shock, do not  
remove the base. No user serviceable parts  
inside. Repair should be done by authorized  
service personnel only.  
Check voltage to be sure that the voltage  
indicated on the name plate is compatible with  
your voltage.  
Never clean with scouring powders or harsh  
chemicals.  
Never make technical changes or use the  
appliance in any manner other than as directed.  
SHORT CORD  
INSTRUCTIONS  
A. We do not recommend using an extension cord  
with this device.  
B. If an extension cord is absolutely necessary :  
1 - The marked electrical rating of the  
extension cord should be at least as great as  
the electrical rating of the appliance.  
2 - To reduce the risk of injury, do not drape  
cord over the counter top or table top where  
it can be pulled on by children or tripped  
over unintentionally.  
3 - The extension cord should be at least 18 AWG.  
4 - The extension cord should be in grounding  
type 3-wire cord  
5
B80 one way T-FAL US modif heineken .qxd:B80 one way SEB Uklta.qxd 25/06/08 15:10 Page 6  
2
General information  
The BeerTender® is designed to dispense chilled beer in  
a domestic setting. Only a Heineken® DraughtKegTM and  
Heineken Premium Light® DraughtKegTM can be used  
with the BeerTender. You should not use any other  
commercially available beer containers or kegs. Do not  
introduce any materials other than the DraughtKeg inside  
the appliance.  
BeerTender is designed for use by responsible adults of  
legal drinking age.  
Guidelines for reading these instructions  
* The warning triangle indicates instructions that are  
important for the user’s safety.  
* Please adhere strictly to these directions to ensure  
proper use and avoid serious injury!  
* This symbol highlights information that is especially  
important for making the best use of the machine.  
6
B80 one way T-FAL US modif heineken .qxd:B80 one way SEB Uklta.qxd 25/06/08 15:10 Page 7  
3
Product description  
BeerTender® components  
1.  
BeerTender at home draughting system  
2.  
3.  
Refrigerating chamber  
Lid  
4.  
5.  
6.  
Lid opening handle  
Control panel  
Tap cover  
7.  
8.  
9.  
Dispensing spout  
Beer tap handle  
Drip grate  
10.  
11.  
12.  
Drip tray  
Main power switch  
Power cord with plug  
Other Components  
13.  
14.  
5 Liter DraughtKegTM (not included)  
Replaceable Draught Beer tube  
(Should be changed with each new DraughtKeg)  
(5 included with purchase)  
4
Before use  
Child Safety Lock  
* Make sure that children can not play with the  
appliance.  
* Do not leave the materials used to pack the appliance  
within children’s reach.  
* To prevent children from using the appliance, you can  
remove the tap handle. To remove the handle, make  
sure that it is in an upright position and pull upward.  
7
B80 one way T-FAL US modif heineken .qxd:B80 one way SEB Uklta.qxd 25/06/08 15:10 Page 8  
Fire prevention  
In the event of a fire, use carbon dioxide (CO2)  
extinguishers.  
Do not use water or powder extinguishers.  
Setup and Maintenance  
* Install the BeerTender® in an upright position in a safe  
place.  
* To ensure that the BeerTender works correctly and  
efficiently, the following is strongly advised:  
* Place it on a perfectly level and stable surface.  
* Choose a clean, well-lit area with an easily accessible  
electric socket.  
* Keep the appliance at a minimum distance (4 inches)  
from the stove as shown in the diagram.  
* Keep the appliance at a minimum distance  
(2 ½ inches) from the walls.  
* Store the DraughtKegTM at room temperature or in the  
refrigerator.  
* Make sure the BeerTender is not exposed to direct  
sunlight.  
* Do not use the BeerTender outdoors.  
* Do not place the BeerTender on very hot surfaces or  
near open flames, as these may melt or damage the  
casing.  
* Your BeerTender uses a technology that delivers  
ultimate cooling results when the ambient temperature  
is between 54°F and 86°F. At colder temperatures, the  
appliance cooling system could be damaged. At warmer  
temperatures, the cooling system will not be able to  
reach the pre-programmed temperature.  
Warning! To avoid overheating, always keep the  
BeerTender appliance out of direct sunlight. To obtain  
good cooling performance, never install your machine in  
a room with an ambient temperature above 86°F.  
5
Using the BeerTender System  
* Always hold the appliance by the bottom edge when  
lifting.  
* To obtain draught beer of optimal quality you should  
keep two basic factors in mind, the temperature of the  
beer and hygienic conditions. Follow these few simple  
steps for the ideal use of BeerTender.  
8
B80 one way T-FAL US modif heineken .qxd:B80 one way SEB Uklta.qxd 25/06/08 15:10 Page 9  
A new draught beer tube should be used with  
each DraughtKegTM  
A bag of 5 tubes is included with the BeerTender®  
appliance. To order additional beer tubes, please  
HEINEKEN.  
Chilling the DraughtKeg  
1. Before pouring a draught beer, it is very important that  
the Heineken® and Heineken Premium Light®  
DraughtKeg reach the correct temperature.  
2. Ensure DraughtKeg is sufficiently chilled before  
pouring a draught beer. Insufficiently chilled  
DraughtKegs will produce too much foam. It is ideal to  
purchase the DraughtKeg pre-chilled or pre-chill over  
night before intended use. If the DraughtKeg needs  
additional chilling, there are 2 recommended options:  
a. Inside the BeerTenderDepending on the  
temperature of the DraughtKeg, it will take up  
to 18 hours to chill to the ideal serving  
temperature.  
b. In a refrigerator – Depending on the  
temperature of your refrigerator, it will take up to  
12 hours to chill to the ideal serving temperature.  
Tip: We recommend that you always keep an extra  
DraughtKeg in your refrigerator to always have a chilled  
keg available.  
Preparing the BeerTender  
IMPORTANT: It is important that the BeerTender power  
switch is turned on before inserting the DraughtKeg.  
9
B80 one way T-FAL US modif heineken .qxd:B80 one way SEB Uklta.qxd 25/06/08 15:10 Page 10  
*
After setting up the BeerTender® and before use, it is  
vital to clean the detachable pour spout – this is the  
only part of the appliance that will come into contact  
with the beer. The spout should be rinsed by hand.  
After cleaning, screw back into place.  
*
*
Before inserting the DraughtKegTM into the  
BeerTender, simply snap the patented disposable  
draught beer tube (5 tubes included) onto the  
DraughtKeg.  
Open the BeerTender cover by pressing in the release  
panel on the top of the machine.  
*
*
*
*
*
*
Place DraughtKeg into BeerTender.  
Remove the tap spout cover by lifting it up.  
Position the draught beer tube as shown in drawing.  
Put the tap spout cover back into place.  
Carefully close the lid.  
Set the drip tray and grate in place at the front of the  
appliance. Make sure the drip tray is properly fitted  
and positioned.  
10  
B80 one way T-FAL US modif heineken .qxd:B80 one way SEB Uklta.qxd 25/06/08 15:10 Page 11  
WARNING! The drip tray must be positioned on a level  
surface and must not jut out from the surface it is resting  
on.  
Control Panel  
Your appliance features a display providing you with  
important and useful information.  
Two LEDs on the top of the lid provide important  
indications:  
Green (ON/OFF) LED on the left of the panel: when lit, it  
indicates that the appliance is operating.  
Green beer-temperature LED on the right side of the  
panel: when the DraughtKegTM has reached the ideal  
temperature the LED switches on and the appliance  
goes into “stand-by” cooling mode.  
Warning: never use your BeerTender® with ambient  
temperature above 86°F. Above that level, the ideal  
serving temperature can not be attained.  
Pouring a beer from the BeerTender  
* Before pouring a beer, rinse a clean glass in cold  
water which chills the glass and wets the inside to  
enable a perfectly smooth draught pour. Use of 8 oz  
glasses is recommended to maintain the ideal serving  
temperature.  
Draught and Drink  
* Be aware that the first glass you pour from every new  
DraughtKeg will contain mostly foam. This is typical of  
draught beer. Allow the foam to settle and continue to  
pour.  
* Tilt and pour: Tilt your glass at a 45 degree angle as  
you pour and adjust upright as the glass fills.  
* Ensure you pull the tap handle all the way down. Not  
opening the handle all the way will result in excessive  
foam.  
* For the optimal draught beer drinking experience,  
serve your beer with a foam head of 2 fingers in height  
(approximately 1.5”).  
11  
B80 one way T-FAL US modif heineken .qxd:B80 one way SEB Uklta.qxd 25/06/08 15:10 Page 12  
Proper Care and Cleaning of your BeerTender®  
* The drip tray and grate should be emptied and  
cleaned after each use.  
* Before cleaning the appliance, it is essential to turn off  
the ON/OFF switch and then pull the plug out of the  
socket.  
* Keep in mind that during use the drip tray will  
have to be emptied and rinsed regularly.  
The tray and grate are dishwasher safe or can be  
washed by hand with a mild detergent. Dry completely.  
* Always wipe down the interior of the BeerTender after  
use. Beer is a natural product that can spoil.  
Therefore, you should always keep the appliance  
clean to maintain the quality of the beer dispensed and  
avoid unpleasant odors.  
* Rinse the pour spout between uses for optimal results.  
Handwash with warm soapy water. Do not wash in  
dishwasher.  
* To remove, unscrew turning counterclockwise  
from main unit. To re-attach, simply screw back  
in place turning clockwise.  
* You should never attempt to access internal parts of  
the appliance.  
IMPORTANT: After cleaning, ensure all parts of your  
BeerTender have completely dried before closing the  
lid.  
Storing the BeerTender  
* When the BeerTender is not being used for a long  
period of time, remove the DraughtKegTM and turn the  
control to “off”.  
* Remove the plug from the power outlet.  
* Store the BeerTender at room temperature in a dry  
place out of children’s reach.  
* Protect from dust and dirt.  
12  
B80 one way T-FAL US modif heineken .qxd:B80 one way SEB Uklta.qxd 25/06/08 15:10 Page 13  
6
Troubleshooting  
Problem  
Possible causes  
Remedies  
The appliance The appliance is Connect the  
does not come not connected to appliance to the  
on.  
the outlet.  
outlet.  
You cannot  
position the tap opened the  
You may have  
Before installing the  
draught beer tube  
cover correctly. draught beer tube onto the  
(white plastic part BeerTender®  
at the end of the tapping mechanism,  
serving tube) by make sure that the  
hand. If so, the  
draught beer tube is  
tap cover will not closed.  
close correctly  
and there is a risk  
for the beer to  
flow out.  
You cannot  
The DraughtKegTM If the draught beer  
position the tap tap or tube is not tube is not installed  
cover correctly. inserted correctly. properly in the  
tapping mechanism  
or if the tube is  
pinched,  
this will affect the  
beer flow. Please  
refer to Section 5:  
Using the  
BeerTender System  
to check that you  
have properly set  
up the BeerTender.  
No beer is being The appliance is Switch the  
dispensed.  
off.  
appliance on.  
13  
B80 one way T-FAL US modif heineken .qxd:B80 one way SEB Uklta.qxd 25/06/08 15:10 Page 14  
No beer is  
being  
The DraughtKegTM Replace the  
is empty.  
DraughtKeg with a  
dispensed.  
new one.  
There is no  
Install a  
DraughtKeg inside DraughtKeg inside  
the BeerTender® the BeerTender  
appliance.  
appliance.  
The BeerTender  
appliance tap  
handle is not  
correctly  
Install/position the  
tap cover correctly.  
installed/positioned.  
You cannot  
The tap cover has Position the tap  
close the lid.  
not been  
positioned  
correctly.  
cover correctly.  
You cannot  
close the lid.  
The DraughtKeg  
has not been  
Install the tap  
correctly. Ensure  
correctly installed. the draught tube  
has been installed  
completely and is  
not preventing the  
lid from closing.  
The  
The DraughtKeg  
has not reached  
the right  
dispensing  
temperature.  
Allow the  
DraughtKeg to cool  
to the right  
temperature. You  
can rely on the  
temperature  
BeerTender  
appliance  
produces too  
much foam  
when  
dispensing  
beer.  
indicator on the  
control panel of  
your BeerTender  
appliance.  
The DraughtKeg  
Wait 4 hours  
has been shaken. before dispensing  
beer.  
The tap handle is Firmly and quickly  
being moved too  
slowly.  
pull the handle  
down and forward  
as far as it will go.  
14  
B80 one way T-FAL US modif heineken .qxd:B80 one way SEB Uklta.qxd 25/06/08 15:10 Page 15  
Beer flows out The tap handle is Open the tap  
too slowly.  
not open all the  
way.  
completely.  
The  
The DraughtKegTM Allow the  
DraughtKeg to cool  
BeerTender® has not been  
appliance is  
dispensing  
warm beer.  
chilled long enough long enough in the  
and is thus not at appliance.  
the right serving  
temperature.  
The  
temperature  
The BeerTender  
appliance is  
Use the appliance  
indoors and move  
indicator on the exposed to too hot it to a room where  
control panel a temperature or the ambient  
does not light direct sunlight (see temperature does  
up.  
also section 5:  
Cooling the keg  
and Installing the  
BeerTender).  
not exceed 86°F.  
Ice forms in the The BeerTender  
Move the  
cooling  
has been installed BeerTender to a dry  
chamber.  
in a humid  
place.  
environment.  
A fault has  
Have the  
occurred in the  
cooling system.  
BeerTender  
repaired by an  
authorized service  
center.  
It is normal for a  
small patch of ice  
to form on the rear  
of the cooling  
chamber (near the  
screws).  
15  
B80 one way T-FAL US modif heineken .qxd:B80 one way SEB Uklta.qxd 25/06/08 15:10 Page 16  
7 - Disposal  
* Check your local ordinances for disposal of  
BeerTender®.  
8 - Consumer service  
If you have additional questions, please call our  
Consumer Service Department.  
It is helpful to have the product available at the time of  
your call and to know the reference number that can  
generally be found on the base of the product.  
USA :  
Phone 1-800-395-8325  
Hours* Monday – Thursday from 8:30 a.m. – 5:00 p.m.  
(EST), Friday 8:30 a.m. – 4:00 p.m. (EST)  
Letters should be addressed to :  
Groupe SEB – Consumer Service  
2121 Eden Road  
Millville NJ, 08332  
Only letters can be accepted. Packages without a  
return authorization number will be refused.  
CANADA  
Phone 1-800-418-3325  
Hours* Monday – Friday 8:30 a.m. – 4:30 p.m. (EST)  
Letters should be addressed to  
Groupe SEB Canada Inc.  
345 Passmore Avenue  
Toronto, Ontario  
Canada, M1V 3N8  
*Please note hours are subject to change.  
16  
B80 one way T-FAL US modif heineken .qxd:B80 one way SEB Uklta.qxd 25/06/08 15:10 Page 17  
9 - Limited Warranty  
ONE YEAR LIMITED WARRANTY  
The manufacturer warrants this product to be defect free in material  
and workmanship for a period of one year from the date of purchase.  
Defective products may be returned by the original purchaser or any  
subsequent owner within the warranty period, postage pre-paid  
together with proof of purchase (register receipt) to an authorized T-fal  
return facility.  
If product is returned without proof of purchase it will be reviewed  
based on the manufacturing production week and year to determine  
warranty coverage.  
Defective products will be replaced at no charge including return  
postage if it falls within the warranty timeframe.  
The warranty does not apply to any unit that has been tampered with,  
nor to damages incurred through improper use and care, faulty  
packing or mishandling by any common carrier.  
The manufacturer's sole obligation and your exclusive remedy under  
this warranty are limited to such replacement. This is a limited  
warranty and is in lieu of all other warranties, express or implied,  
including merchantability. This warranty gives you specific legal  
rights.You may also have other legal rights varying from state to state.  
If you have a claim:  
1) Do not return the product to the retailer from which it was  
purchased.  
2) Please contact our consumer service department (1-800-395-8325  
M-Th 8:30am - 5pm & Fr 8:30am - 4pm EST) for assistance and to  
ensure the fastest possible resolution to the problem. Please have  
the model or type number of your product on hand.  
3) If it is determined that you should return your product for  
replacement - send the product along with original proof of  
purchase and a description of the problem to the closest  
authorized T-fal return facility  
4) Be sure to include your name, address and home telephone  
number with your shipment. Another contact number is suggested  
in case you need to be contacted.  
5) Returns must be sent with all shipping charges pre-paid. We  
suggest that you carefully wrap your package for shipping and  
send by insured and/or by traceable means.  
17  
B80 one way T-FAL US modif heineken .qxd:B80 one way SEB Uklta.qxd 25/06/08 15:10 Page 18  
ONE YEAR LIMITED WARRANTY  
What happens to my return?  
If the inspection shows that the product is defective, under our Limited  
Warranty, the return facility will notify T-fal to replace the defective part  
or product at no cost to you. Comparable substitutions are based on  
replacement product availability and at the sole discretion of the  
Manufacturer.  
If the inspection shows that the product is not defective under our  
Limited Warranty we will notify you. Shipping charges may apply to  
product not covered under warranty.  
* Please allow 5 - 10 business days to process your return.You will be  
notified if a repair will take longer.  
This product has been designed for domestic use only. Any  
professional use, inappropriate use or failure to comply with the  
instructions, the manufacturer accepts no responsibility and the  
warranty will not apply.  
Read the instructions for use carefully before using your appliance for  
the first time.  
Any use which does not conform to these instructions will absolve T-fal  
from any liability.  
18  
B80 one way T-FAL US modif heineken .qxd:B80 one way SEB Uklta.qxd 25/06/08 15:10 Page 19  
19  

Westinghouse LD 3240 User Manual
Vita Mix High Performance Commercial Blenders User Manual
Victor 1297 User Manual
Ultra Products ATX Cases Defender User Manual
Tekkeon ezTalker ET3000 User Manual
Sony DCR TRV9E User Manual
Sony Camcorder HDC1500R User Manual
Sony Camcorder DXC D30WS User Manual
Sharp XE A42S User Manual
Sanyo Camera Lens User Manual