MDX-61
US Model
Canadian Model
AEP Model
SERVICE MANUAL
Ver 1.1 2001.08
UK Model
E Model
This set is automatic electrical adjustment.
Model Name Using Similar Mechanism
Base Mechanism Type
MDX-60
MG-798-133
KMS-193C/J2N
Optical Pick-Up Name
SPECIFICATIONS
System
Laser Diode Properties
Material: GaAlAs
Mini disc digital audio system
Current drain
300 mA (MD playback)
600 mA (during loading or ejecting a disc)
Wavelength: 780nm
Emission Duration: Continuous
Dimensions Approx. 176×83.5×125 mm
(7×33/8×5 in.) (w/h/d)
Laser out-put Power: Less than 44.6µW*
* This output is the value measured at a distance
of 200 mm from the objective lens surface on
the Optical Pick-up Block.
not incl. projecting parts and controls
Approx. 1.1 kg (2 lb. 7 oz.)
Power requirement
12 V DC car battery
(negative ground)
Supplied accessories
Mass
Frequency response
20–20,000 Hz
Wow and flutter
Below measurable limit
Signal-to-noise ratio
Mounting hard ware (1 set)
Bus cable 5.5 m (1)
RCA pin cord 5.5 m (1)
95 dB
Output
Bus control output (8 PIN)
Analog audio output (RCA PIN)
• U.S. and foreign patents licensed from Dolby Laboratories
Licensing Corporation.
• Design and specifications subject to change without notice.
– Continued on next page –
MINIDISC CHANGER
9-925-528-12
Sony Corporation
2001H0500-1
e Vehicle Company
C 2001.8
Shinagawa Tec Service Manual Production Group
SECTION 1
GENERAL
This section is extracted
from instruction manual.
– 3 –
– 4 –
– 5 –
– 6 –
SECTION 2
DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.
FRONT PANEL ASS’Y, CASE (UPPER)
5 case (upper)
1 two screws (B2.6 × 6)
1 two screws
(B2.6 × 6)
2 claw
3 front panel ass’y
2 claw
4 connector (CN620)
1 two screws (B2.6 × 8)
REAR PANEL ASS’Y, MD SECTION
2 rear panel ass’y
6 two springs
4 two dampers
7
3 flexible board
(CN800)
4 two dampers
6 two springs
5 two springs
– 7 –
CHASSIS (GEAR) ASS’Y, MAIN BOARD
1 three screws (P1.7 × 1.8)
2 chassis (gear) ass’y
3 special flat screw (1.7 × 3)
4 flexible board (CN500)
5 connector (CN602)
3 two special flat screws
(1.7 × 3)
6 flexible board (CN610)
7 three connectors
(CN603, 700, 701)
8 MAIN board
CHASSIS (BASE) ASS’Y, CHASSIS (OP) ASS’Y
3 worm wheel (LD)
5 Pull up the chassis (OP) ass’y
in the arrow A direction.
1 four screws (P1.7 × 1.8)
A
1 screw (P1.7 × 1.8)
1 screw (P1.7 × 1.8)
2 feed screw (ELV) ass’y
4 chassis (base) ass’y
– 8 –
SERVO BOARD
2 three special head screws (M1.7 × 2)
3 flexible board (CN100)
5 connector (CN301)
6 servo board
1 flexible board (CN200)
4 flexible board (CN400)
OPTICAL PICK-UP (KMS-193C/J2N)
1 two screw (K1.7 × 3.5)
2 optical pick-up
(KMS-193C/J2N)
– 9 –
SECTION 3
DIAGRAMS
• Circuit Boards Location
SW board
POWER board
MAIN board
SERVO board
LAMP board
– 10 –
MDX-61
3-1. BLOCK DIAGRAM
OPTICAL PICK-UP BLOCK
(KMS-193C/J2N)
IC100
RF AMP
IC600
SYSTEM CONTROLLER
IC900
BUS INTERFACE
IC601
RESET
DETECTOR
CNP1
(BUS CONTROL CONNECTOR)
RESET
SW
XRST
XLAT
SWDT
SCLK
59
58
45
51
12
7
4
3
17
18
19
20
44
XRST
SWDT
SCLK
XLAT
MD-RST
MD-LAT
MD-SO
F
XRST
30
48
50
49
61
8
7
4
6
F
RST
UNICKI
UNISO
UNISI
2
C
B
SWDT
SCLK
XLAT
RFO
1
4
2
5
3
6
10
11
9
IC500
8
7
MD-CKO
SHOCK PROOF MEMORY CONTROLLER
ATRAC ENCODER/DECODER
IC200
C B
D A
9
48
J
DIGITAL SIGNAL PROCESSOR
I
J
IC602
DIGITAL SERVO SIGNAL PROCESSOR,
EFM/ACIRC ENCODER/DECODER
LEVEL SHIFT
8
4
5
3
2
5
A
D
E
I
43
41
26
29
33
34
35
38
39
AGCI
RF
10
13
4
3
XLAT
SCK
58
77
76
82
68
67
65
64
10
9
XLAT
SCLK
SWDT
XRST
SENS
SRDT
SQSY
FOK
RFI
XLAT
SCLK
SWDT
XRST
SENS
SRDT
SQSY
FOK
SENS
SRDT
SQSY
FOK
3
5
4
6
54
52
62
64
55
SENS
MD-SI
SQSY
FOK
6
E
TE
TE
2
SW
BUS-ON
2
SWDT
XRST
SENS
SRDT
47
8
SE
SE
17
6
16
12
11
14
2
ADFG
AUX
FE
ADFG
AUX1
FE
9
8
5
BATTERY DET
Q920, 921
60
67
BU-IN
AUTOMATIC
POWER CONTROL
Q100
BOTM
PEAK
BOTM
PEAK
11
1
10
2
14
10
AAPC
PD
LD
PD
R-CH
(R)
30
29
3
93
DTO
DATA
9
X INT
CC-XINT
A-MUT
DTI
MUTING
CONTROL
SWITCH
Q800
97
92
91
90
87
DFCT
C2PO
BCK
MIN
MUTING
SWITCH
37
66
ABCD
ABCD
AUX2
MUTING
31
32
33
35
C2PO
BCK
LINE
OUTPUT
Q810, 820
Q560, 561
IC550
D/A CONVERTER
LRCK
XTAI
LRCK
SPO
IC800
LINE AMP
PEAK HOLD
Q200
78
84
SERIAL
INPUT
41
44
1
3
LPF
8
5
3
D OUT
ALRCK
DAC
DAC
+
–
1
2
(L)
IC201
INVERTER
36
37
OSC O
OSCI
LPF
R-CH
X500
45.1584MHz
11
4
2
APC REF
LDDR
+3.3V
+3.3V REG.
Q931
4
(D/A CONV)
IC501
RAM
13
40
10
HOME MDMON
S901
(HOME POSITION DET)
AO0 55
9
ı
A0
+9V
+9V REG.
Q940, 941
ı
52
12
·
(LINE AMP)
Q500, 501
SWITCHING
RV901
ELEVATOR HIGHTER
POSITION DET(EHS)
·
EHS
56
ı
14
ı
8
6
5
87
FFDR
+5V
AO8 60
18 A8
(PULL UP)
+6V REG.
Q910, 911
FOCUS
+5V
D0 69
1
·
D0
11
29
89
86
FRDR
TFDR
(SYSTEM CONTROLLER)
Q950
B+ SWITCH
·
56
LIMIT-SW
68
2
·
S400
(LIMIT DET)
·
70
+5V
+5V REG.
Q952
IC950
24
·
31
32
·
(MOTOR DRIVE)
REGULATOR CONTROL
D4 71
25 D3
TRACKING
14 DCS1
ı
61
62
65
66
67
22
23
5
4
3
XOE
XCAS
A09
XRAS
XWE
DE
CAS
AB
RAS
WE
DCS6
19
14
13
26
22
85
93
TRDR
SPRD
ERROR
AMP
S611-616
(EJECT)
COMP
COMP
OUT
OUT
10
7
20
M901
SPINDLE
57
DOOR-SW
M
M
S620
DOOR OPEN
/CLOSE DET
24
13
19
18
94
91
SPFD
4
3
ERROR
AMP
SRDR
11
12
M902
SLED
LES
SES
+3.3V REG.
Q953
+5V REG.
Q954
+3.3V
S902
(LES)
15
17
92
SFDR
PL620
LAMP DRIVE
Q600, 601
ILLUMINATION
LAMP
IC300
SLED/SPINDLE MOTOR DRIVE,
FOCUS/TRACKING COIL DRIVE
S903
(SES)
IC700
ELEVATOR MOTOR DRIVE
21
63
32
ILL ON
9
2
4
6
7
M1
M904
(ELEVATOR)
STR-SW
XTAL
M
S600
(STOP)
(SHASSIS)
7
M1
• R-CH : Same as L-ch
• SIGNAL PATH
: PLAY
X600
10MHz
IC701
LOADING MOTOR DRIVE
31
34
EXTAL
TX
9
2
4
8
9
M2
M2
M903
(LOADING)
X601
32.768kHz
M
7
35
TEX
– 11 –
– 12 –
• IC Block Diagrams
– SERVO section –
– MAIN section –
IC200 CXD2535CR-1
IC501 HM51W4400TT6-8
GND
D4
1
2
3
4
5
6
7
8
9
D1
D2
26
25
75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59
58 57 56 55 54
53 52 51
CLOCK OSC
50
DVSS
XWE
XRAS
NC
24 D3
DIN PLL
(22 MHz)
49 DIPO
34 MHz
PLL
76
77
78
79
80
SE
TE
XCAS
ANALOG MUX
OP AMP
23
TEST2
MVC1
COMP
48
47
22 XOE
21 NC
20 NC
19 NC
18 A8
17 A7
16 A6
15 A5
14 A4
ECC
ENCODER/
DECODER
A0–A9
COLUMN DECODER
TENV
MID
APC
NC
A/D
CONVERTER
46 RAOF
NC
A9
A0
SENSE REFRESH AMP
INPUT/OUTPUT CONTROL SWITCH
REGISTER
EFM
MODULATOR
EFMO
45
32K RAM
TEST1 81
ADFG 82
A1 10
A2 11
EFM
A0–A9
MEMORY CELL
(4194204 BIT)
XPLCK
44
DIGITAL PLL
REGISTER
83
84
85
86
TS25
LDDR
TRDR
TFDR
EFM
12
A3
GFS
43
42
41
SERVO DSP
DEMODULATOR
EFM SYNC
DETECTOR/
PROTECTOR
GTOP
WFCK
VDD 13
TRACKING PWM
FOCUS PWM
SLED PWM
TRACKING SERVO
FOCUS SERVO
SLED SERVO
FFDR 87
RFCK
WDCK
DVDD
XBCK
MCLK
XTAI
40
39
38
37
36
35
34
33
32
31
DVDD
FRDR
88
89
IC550 CS4330-KSR-H
IC700, 701 LB1638M
PWM GENERATOR
SUBCODE Q
READER/
FS4 90
GENERATOR
10
9
1
N.C.
GND
VOLTAGE REFERENCE
1
SDATAI
SRDR 91
SERIAL INPUT
INTERFACE
ADIP
DEMODULATOR
ADIP
DECODER
92
SFDR
2
3
DEM/SCLK
LRCK
INTERPOLATOR
AOUT L
VA+
AGND
AOUT R
8
7
6
5
CLOCK
GENERATOR
ANALOG
LOW-PASS
FILTER
XTAO
LRCK
BCK
SPRD
93
DELTA-SIGMA
MODULATOR
2
OUT1
IN1
DAC
DIGITAL
SPFD 94
95
DE-EMPHASIS
CLV
APC COMP./
FILTER
APC PWM
GENERATOR
8
7
VS
DCLO
PROCESSOR
MCLK
4
SUBCODE
P~W
PROCESSOR
C2PO
VCC
IN2
3
4
DCLI 96
XDCL 97
OUT2
AUDIO
DATA
DTO
30
CONTROL
29 DTI
SENS
CONTROL
SERVO AUTO
SEQUENCER
5
6
N.C.
GND
DIDT
DODT
DOVF
28
27
26
DIGITAL
AUDIO
IN/OUT
OFTRK/DFCT/
FOK/C OUT/
SHCK/TEOK
PROCESSOR
OFTRK 98
SERVO
– POWER section –
IC900 MM1284XFFE
CPU I/F
PEAK
DETECT
99
COUT
CONTROL
DVSS 100
IC950 TL1451ACDB-E20
1
2
3
4
5
6
8
9
10 11 12
13
14 15 16
7
17 18 19 20 21 22 23 24 25
14 VCC
1
2
3
4
5
6
SW
SW
BUS ON OUT
BUS ON INPUT
GND
13 BUS ON
12 LINK OFF
11 CLK OUT
16
VERF.
15
14
13
12
11
10
9
IC300 MPC17A38ZVMEL
+2.5V
BUS CLK
VCC
–
36
7
12 16
8
11
9
10 15
13 14 21 25 30 29 26 27 28 22
24 23
+
VREF
REFERENCE
VOLTAGE
PWM
COMPA-
RATOR2
ERROR
AMP2
BUS DATA
10
9
DATA OUT
DATA IN
+2.5V
VERF
OUTPUT2
OUTPUT1
SHORT
CIRCUIT
PROTECTION
COMPARATOR
DRIVER
DRIVER
PRE-DRIVER
CONTROL
DRIVER
DRIVER
PRE-DRIVER
CONTROL
G
1
VERF
VERF
RESET
SW
7
8
RESET
DC/DC
CONVERTER
BUS RESET
+
+
–
S
R
R
PRE-DRIVER
CONTROL
PRE-DRIVER
LATCH
U.V.L.O
VREF/2
PWM
COMPA-
RATOR1
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
CLOCK
CLK
DETECTOR
+
–
CONTROL
TRIANGLE
OSCILLATOR
ERROR
AMP1
GND
2
3
4
5
6
7
8
1
35
6
5
17 18
19
2
3
31 32
20
4
33
34
– 32 –
– 31 –
3-8. IC PIN FUNCTION DESCRIPTION
SERVO BOARD IC100 CXA1981AR (RF AMP)
Pin No. Pin Name
I/O
O
I
Function
Output terminal for the center point voltage (1/2 VCC) generated
Signal input from detector circuit in the optical pick-up block
Signal input of the operational amplifier for F signal
Signal output of the operational amplifier for F signal
Front monitor Connected to the photo diode
1
2-7
8
VC
A-F
FI
I
9
FO
O
I
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47, 48
PD
APCREF
TEMPI
GND
AAPC
DAPC
TEMPR
XRST
SWDT
SCLK
XLAT
VREF
TENV
THLD
VCC
I
Input terminal for the setting of laser power
I
Terminal for the connection to temperature sensor Not used this set (OPEN)
Ground terminal
–
O
O
O
I
LD amplifier output terminal of APC circuit
Not used (OPEN)
Output terminal of the reference voltage for temperature sensor Not used this set (OPEN)
Reset signal input from the system controller (IC600)
When reset : “L”
I
Write data signal input from the system controller (IC600)
Clock signal input from the system controller (IC600)
Latch signal input from the system controller (IC600)
Reference voltage output Not used this set (OPEN)
Not used (OPEN)
I
I
O
O
I
Not used (OPEN)
–
I
Power supply terminal (+3.3V)
TFIL
Not used (OPEN)
TE
O
I
Tracking error signal output to CXD2535CR (IC200)
TLB
Input terminal of the adder signal to tracking error
Terminal for the sled error lowpass filter
Not used this set (OPEN)
CSLED
SE
I
O
O
I
Sled error signal output to CXD2535CR (IC200)
FM signal output terminal of the ADIP
ADFM
ADIN
ADAGC
ADFG
AUX
Input terminal by AC coupling is FM signal of the ADIP
External capacitor connect terminal for AGC of the ADIP
ADIP double turned FM signal output to CXD2535CR (IC200)
Sub signal output to CXD2535CR (IC200)
I
O
O
O
I
(22.05kHz ± 1kHz)
FE
Focus error signal output to CXD2535CR (IC200)
FLB
Input terminal of the adder signal to focus error
Not used this set (OPEN)
ABCD
BOTM
PEAK
PFAGC
RF
O
O
O
I
Light amount signal output to CXD2535CR (IC200)
Light amount bottom hold signal output to CXD2535CR (IC200)
Light amount peak hold signal output to CXD2535CR (IC200)
External capacitor connect terminal of AGC circuit for the RF
Playback EFM RF signal output to CXD2535CR (IC200)
O
I
ISET
Setting terminal for the internal circuit constant
Input terminal by AC coupling is RF signal
RF signal output terminal
22kHz, BPF center frequency
AGCI
RFO
I
O
I
MORFI
MORFO
I, J
Input terminal by AC coupling is RF signal of the MO
RF signal output terminal of the MO
O
I
Signal input from detector circuit in the optical pick-up block
– 33 –
SERVO BOARD IC200 CDX2535CR-1 (DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO SIGNAL PROCESSOR, EFM/ACIRC
ENCODER/DECODER)
Pin No. Pin Name
I/O
O
O
O
O
I
Function
1
2
FS256
FOK
11.2896MHz clock signal output (MCLK system) Not used this set (OPEN)
Focus OK signal output to the system controller (IC600) “H” is output when the focus is applied
Defect ON/OFF selection signal output to CXD2536CR (IC500)
Track jump detection signal output to the system controller Not used this set (OPEN)
Track jump detection enable input Not used this set (Fixed at “L”)
Laser power selection signal input from the system controller Not used this set (Fixed at “L”)
Not used this set (Fixed at “H”)
3
DFCT
SHCK
SHCKEN
WRPWR
DIRC
4
5
6
I
7
I
8
SWDT
SCLK
XLAT
SRDT
SENS
I
Write data signal input from the system controller (IC600)
9
I
Serial clock signal input from the system controller (IC600)
10
11
12
13
I
Serial latch signal input from the system controller (IC600)
O
Read data signal output to the system controller (IC600)
O (3) Internal status (SENS) output to the system controller (IC600)
ADSY
O
ADIP sync signal output Not used this set (OPEN)
Sub-code Q sync (SCOR) output to the system controller (IC600)
“L” every 13.3msec, Almost “H”
14
15
SQSY
DQSY
O
Digital in U-bit CD format sub-code Q sync (SCOR) output to the system controller (IC600)
“L” every 13.3msec, Almost “H”
O
16
17
18
19
20
21
22
23
XRST
TEST4
CLVSCK
TEST5
DOUT
DIN
I
I
Reset sigmal input from the system controller (IC600) When reset “L”
Test input terminal (Fixed at “L”)
O
I
Not used this set (OPEN)
Test input terminal (Fixed at “L”)
O
I
Output terminal of the digital audio signal (for optical out) Not used this set (OPEN)
Input terminal of the digital audio signal (for optical out) Not used this set (Fixed at “L”)
FM modulation clock signal output of the ADIP Not used this set (OPEN)
ADIP CRC flag output When error “H” Not used this set (OPEN)
Record/playback selection signal input
FMCK
ATER
O
O
24
REC
I
When recording :“H”, when playback :“L” (Fixed at “L”)
Ground terminal (Digital system)
25
26
27
28
29
30
DVSS
DOVF
DODT
DIDT
DTI
–
I
Validity flag input terminal for the digital audio out Not used this set (Fixed at “L”)
Input terminal of 16-bit data signal for the digital audio out Not used this set (Fixed at “L”)
Output terminal of 16-bit data signal for the digital audio in Not used this set (OPEN)
Record audio data signal input from CXD2536CR (IC500)
I
O
I
DTO
O (3) Plyback audio data signal output to CXD2536CR (IC500)
C2PO (indicate the error state of the data) signal output to CXD2536AR (IC500)
O
31
C2PO
Playback : C2PO (“H”), Digital recording : D. In-Vflag, Analog recording : “L”
32
33
34
35
36
37
38
39
40
BCK
LRCK
XTAO
XTAI
O
O
O
I
Bit clock (2.8224MHz) signal output to CXD2536CR (IC500) (MCLK system)
L/R clock (44.1kHz) signal output to CXD2536CR (IC500) (MCLK system)
System clock (512Fs=22.5792MHz) signal output Not used this set (OPEN)
System clock (512Fs=22.5792MHz) signal input from CXD2536CR (IC500)
MCLK clock (22.5792MHz) signal output Not used this set (OPEN)
BCK (pin #™) inverted output Not used this set (OPEN)
MCLK
XBCK
DVDDO
WDCK
RFCK
O
O
–
Power supply terminal (+3.3V) (Digital system)
O
O
WDCK clock (88.2kHz) signal output (MCLK system) Not used this set (OPEN)
RFCK clock (7.35kHz) signal output (MCLK system) Not used this set (OPEN)
– 34 –
Pin No. Pin Name
I/O
Function
WFCK clock (7.35kHz) signal output (When playback : EFM decoder PLL system,
When recoding : EFM encoder PLL system) Not used this set (OPEN)
Opens the playback EFM frame sync protection window when “H” Not used this set (OPEN)
The playback EFM frame sync and interpolation protection timing match when “H”
Not used this set (OPEN)
41
WFCK
O
42
43
GTOP
GFS
O
O
EFM decoder PLL clock (98Fs=4.3218MHz) signal output Falling edge of the EFM PLL clock and
the EFM signal match Not used this set (OPEN)
44
45
XPLCK
EFMO
O
O
FM signal output (When recoding) Not used this set (OPEN)
Overflow detection signal output of the internal RAM (Decoder monitor out)
RAOF is signal generated when the 32k RAM exceeds the ±4F jitter margin
Not used this set (OPEN)
46
RAOF
O
47
48
MVCI
I
I
Oscillation input for PLL of the digital in Not used this set (Fixed at “L”)
Test terminal input (Fixed at “L”)
TEST2
Phase comparator output for PLL of the digital in When the internal VCO : Frequency ; Low→“H”
When the external VCO : Frequency ; Low→“L” Not used this set (OPEN)
49
DIPD
O (3)
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
DVSS1
DICV
DIFI
–
Ground terminal (Digital system)
I (A)
I (A)
Control voltage input terminal of the internal VCO for digital in PLL
Filter input terminal of the internal VCO for digital in PLL Not used this set (Fixed at “L”)
DIFO
AVDD1
ASYO
ASYI
BIAS
RFI
O (A) Filter output terminal of the internal VCO for digital in PLL Not used this set (OPEN)
–
Power supply terminal (+3.3V) (Analog system)
O
Playback EFM full-swing output (L=VSS, H=VDD)
Playback EFM asymmetry comparate voltage input terminal
Playback EFM asymmetry circuit constant current input terminal
Playback EFM RF signal input from CXA1981AR (IC100)
Ground terminal (Analog system)
I (A)
I (A)
I (A)
–
AVSS1
CLTV
PCO
I (A)
VCO control voltage input terminal of the PLL for decoder PLL master clock
O (3) Phase comparator output terminal of the PLL for decoder PLL master clock
I (A) Filter input terminal of the PLL for decoder PLL master clock
O (3) Filter output terminal of the PLL for decoder PLL master clock
FILI
FILO
PEAK
BOTM
ABCD
FE
I (A)
I (A)
I (A)
I (A)
I (A)
I (A)
Light amount peak hold signal input from CXA1981AR (IC100)
Light amount bottom hold signal input from CXA1981AR (IC100)
Light amount signal input from CXA1981AR (IC100)
Focus error signal input from CXA1981AR (IC100)
Sub signal input from CXA1981AR (IC100)
AUX1
VC
Center point voltage (1/2 VCC)
input from CXA1981AR (IC100)
ADIO
TEST3
AVDD2
ADRT
ADRB
AVSS2
SE
O (A) Monitor output of the A/D converter input signal Not used this set (OPEN)
I (A)
–
Test input terminal (Fixed at “L”)
Power supply terminal (+3.3V) (Analog system)
A/D converter action limits (upper side) voltage input (Fixed at “H”)
A/D converter action limits (lower side) voltage input (Fixed at “L”)
Ground terminal (Analog system)
I (A)
I (A)
–
I (A)
I (A)
I (A)
Sled error signal input from CXA1981AR (IC100)
Tracking error signal input from CXA1981AR (IC100)
Sub signal input terminal from CXA1981AR (IC100)
TE
AUX2
– 35 –
Pin No. Pin Name
I/O
I (A)
I (A)
I
Function
79
80
81
DCHG
APC
Connected to the Ground
Input terminal for the laser APC Not used this set (Fixed at “L”)
Test input terminal (Fixed at “L”)
TEST1
ADIP double turned FM signal input from CXA1981AR (IC100)
(22.05kHz ± 1kHz) (TTL schmitt input)
Test input terminal (Fixed at “L”)
82
ADFG
I
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
TS25
LDDR
TRDR
TFDR
FFDR
DVDD1
FRDR
FS4
I
O
O
O
O
–
Laser APC signal output to CXA1981AR (IC100)
Tracking servo drive signal outuput (–)
Tracking servo drive signal outuput (+)
Focus servo drive signal output (+)
Power supply terminal (+3.3V) (Digital system)
Focus servo drive signal output (–)
O
O
O
O
O
O
O
I
176.4kHz clock signal output (MCLK system) Not used this set (OPEN)
Sled servo drive signal output (+)
SRDR
SFDR
SPRD
SPFD
Sled servo drive signal output (–)
Spindle servo drive signal output (+)
Spindle servo drive signal output (–)
DCLO
DCLI
Not used (OPEN)
Not used (Fixed at “H”)
XDCL
OFTRK
COUT
DVSS2
O
O
O
–
Not used (OPEN)
Offtrack signal output Not used this set (OPEN)
Traverse count signal output Not used this set (OPEN)
Ground terminal (Digital system)
*:On I/O section
(3): 3 state output (A): Analog output
– 36 –
MAIN BOARD IC500 CXD2536R (SHOCK PROOF MEMORY CONTROLLER, ATRAC ENCODER/DECODER)
Pin No. Pin Name
I/O
Function
1
2
VDD
SWDT
SCK
–
Power supply terminal (+3.3V)
I
Write data signal input from the system controller (IC600)
Serial clock signal input from the system controller (IC600)
Serial latch signal input from the system controller (IC600)
Read data signal output to the system controller (IC600)
3
I
4
XLAT
SRDT
SENSE
SMDO
SMDI
XINT
I
5
O/Z
6
O/Z
Internal status (SENSE) output to the system controller (IC600)
Serial command control mode input from the system controller (Fixed at “H”)
Serial command control mode input from the system controller (Fixed at “H”)
Interruption status output to the system controller (IC600)
Record/playback selection signal input (Fixed at “L”)
7
I
I
8
9
O
I
10
11
RCPB
WRMN
I
Write/monitor mode selection signal input from the system controller (Fixed at “L”)
Writing data transmission timing input from the system controller
Used together with the magnetic field head ON/OFF output (Fixed at “L”)
Ground terminal
12
TX
I
13
14
VSS
SICK
IDSL
XILT
–
I
Chip reserve terminal (Fixed at “H”)
15
I
Chip reserve terminal (Fixed at “H”)
16
I
Chip reserve terminal (Fixed at “H”)
17
XRST
TS0-TS3
EXIR
SASL
SGL
I
Reset signal input from the system controller (IC600) When reset : “L”
Test input terminal (Fixed at “L”)
18-21
22
I
I
Chip reserve terminal (Fixed at “L”)
23
I
Single use the block selection “L” : ATRAC, “H” : RAM controller (Fixed at “L”)
Normally fixed at “L”, Fixed at “H” when the ATRAC or RAM controller is single used (Fixed at “L”)
Ground terminal
24
I
25
VSS
–
Record/playback mode signal output terminal of the ATRAC or external audio block
Not used this set (OPEN)
26
AIRCPB
O
27
28
XRQ
ADTO
ADTI
XALT
ACK
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
O
XRQ signal input/output terminal of the ATRAC interface Not used this set (OPEN)
Decoder data signal input/output terminal of the ATRAC Not used this set (OPEN)
Encoder data signal input/output terminal of the ATRAC Not used this set (OPEN)
Data ready and XALT signal input/output terminal of the ATRAC interface Not used this set (OPEN)
ACK signal input/output terminal of the ATRAC interface Not used this set (OPEN)
Error data signal input/output terminal of the ATRAC interface Not used this set (OPEN)
Lch Start data signal input/output terminal of the ATRAC interface Not used this set (OPEN)
EXE signal input/output terminal of the ATRAC interface Not used this set (OPEN)
MUTE signal input/output terminal of the ATRAC interface Not used this set (OPEN)
45.1584MHz clock oscillation output
29
30
31
32
AC2
33
LCHST
EXE
34
35
MUTE
OSCO
OSCI
36
37
I
45.1584MHz clock oscillation input
38
VSS
–
Ground terminal
39
ATT
I/O
O
ATT signal input/output terminal of the ATRAC interface Not used this set (OPEN)
11.6msec timing signal output terminal of the ATRAC block Not used this set (OPEN)
Monitor/audio decode data signal output to the D/A converter (IC550)
Recording data signal input Not used this set (Fixed at “L”)
Bit clock signal output Not used this set (OPEN)
40
F86
41
DOUT
ADIN
ABCK
ALRCK
SA2-SA0
A11,A10
O
42
I
43
O
44
O
L/R clock signal output to the D/A converter (IC550)
45-47
48, 49
O
Address signal output Not used this set (OPEN)
O
Address signal output Not used this set (OPEN)
– 37 –
Pin No. Pin Name
I/O
Function
50
51
VSS
VDD
–
–
Ground terminal
Power supply terminal (+3.3V)
Address signal output to the RAM (IC501)
Address signal output to the RAM (IC501)
52-55
56-60
61
A03-A00
A04-A08
XOE
O
O
O
Output enable control signal output to the RAM (IC501)
Column address strobe signal output to the RAM (IC501)
Ground terminal
62
XCAS
VSS
O
63
–
64
XCS
O
Chip select signal output Not used this set (OPEN)
65
A09
O
Address signal output to the RAM (IC501)
66
XRAS
XWE
D1,D0
D2,D3
D4-D6
VSS
O
Row address strobe signal output to the RAM (IC501)
67
O
Reading/Writing control signal output to the RAM (IC501)
RAM (IC501) data bus
68,69
70,71
72-74
75
I/O
I/O
I/O
–
RAM (IC501) data bus
Data bus Not used this set (OPEN)
Ground terminal
76
D7
I/O
Data bus Not used this set (OPEN)
Input /output terminal of the error (C2PO) data signal to the external RAM
Not used this set (OPEN)
77
78
ERR
I/O
I
External RAM selection signal input for the error data writing (When “H” : External RAM)
(Fixed at “L”)
EXTC2R
79
80
81
82
BUSY
EMP
FUL
O
O
O
O
BUSY signal output of the RAM access Not used this set (OPEN)
Empty or before the full of the ATRAC data (When DSC=ASC+1 : “H”) Not used this set (OPEN)
Full or before the empty of the ATRAC data (When ASC=DSC+1 : “H”) Not used this set (OPEN)
Empty of the ATRAC data (When DSC=ASC : “H”)
EQL
Indicate the main/sub of the recording or playback data (When sub and linking : “H”,
When the main : “L”) Not used this set (OPEN)
83
MDLK
O
84
85
86
87
88
89
90
91
CPSY
CTMD0
CTMD1
SPO
O
O
O
O
–
Interpolation sync signal output Not used this set (OPEN)
DSC (Difference Signal Control) counter mode output Not used this set (OPEN)
DSC (Difference Signal Control) counter mode output Not used this set (OPEN)
System clock (512Fs=22.5792MHz) signal output to CXD2535CR (IC200) and D/A converter (IC550)
Ground terminal
VSS
MDSY
LRCK
BCK
O
I
Sync detection signal output of the main data Not used this set (OPEN)
L/R clock (44.1kHz) signal input from CXD2535CR (IC200)
Bit clock (2.8224MHz) signal input from CXD2535CR (IC200)
C2PO (indicate the error mode of the data) signal input from CXD2535BR (IC200)
When playback : C2PO (“H”), When digital recording : D. IN-Vflag, When analog recording : “L”
When recording : Record audio data signal output (Not used this set)
When playback : Playback audio data signal input from CXD2535CR (IC200)
16-bit data input terminal for the digital audio in Not used this set (Fixed at “L”)
16-bit data output terminal for the digital audio out Not used this set (OPEN)
Disc drive, Record or playback mode output of the EFM encoder/decoder Not used this set (OPEN)
Defect ON/OFF selection signal input from CXD2535CR (IC200)
IN/OUT selection input terminal of the pin *¶ (“L” : IN, “H” : OUT) (Fixed at “H”)
Internal master clock signal output terminal of the RAM controller
Ground terminal
I
92
93
C2PO
DATA
I
I/O
94
95
DIDT
DODT
DIRCPB
MIN
I
O
O
I
96
97
98
SPOSL
MCK
I
99
O
–
100
VSS
– 38 –
MAIN BOARD IC600 CXP84340-043Q (SYSTEM CONTROLLER)
Pin No. Pin Name
I/O
I
Function
Test key (4 × 8 matrix) signal output terminal (Fixed at “L”)
Elevator motor (M904) drive signal output (UP) *1
Elevator motor (M904) drive signal output (DOWN) *1
Loading motor (M903) drive signal output *2
1-5
6
T13-T17
M1
O
O
O
O
O
I
7
M1
8
M2
9
M2
Loading motor (M903) drive signal output *2
10
11
12
13
14
15
16
17
18
19
20
21
22-29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
MDMON
LES
Power control output (Mechanism deck system) Power ON : "H"
Detection signal input from the loading end sensor switch (S902)
Detection signal input from the store end sensor switch (S903)
Detection signal input from the home position switch (S901) Home position : "L"
Detection signal input from the disc1 switch (S611) No disc "L"
Detection signal input from the disc2 switch (S612) No disc "L"
Detection signal input from the disc3 switch (S613) No disc "L"
Detection signal input from the disc4 switch (S614) No disc "L"
Detection signal input from the disc5 switch (S615) No disc "L"
Detection signal input from the disc6 switch (S616) No disc "L"
Changer/single setting up terminal When used the changer : "H" (Fixed at "H")
Lamp (PL620) drive signal outuput for illumination When lamp is ON : "H"
Not used (OPEN)
SES
I
HOME
DCS1
DCS2
DCS3
DCS4
DCS5
DCS6
CH/SINGLE
ILLON
N.C.
I
I
I
I
I
I
I
I
O
O
I
RST
System reset signal input When reset : "L"
EXTAL
XTAL
VSS
I
10MHz system clock signal input
O
–
O
I
10MHz system clock signal output
Ground terminal
TX
32.768kHz clock signal output for a clock
TEX
32.768kHz clock signal input for a clock
AVSS
AVREF
INIT
–
–
I
Ground terminal (Analog system)
Reference voltage (+5V) input for the A/D converter
Initial reset signal input (Normally : "H")
TEMP
EHS
I
Temperature detection signal input
I
Disc hight position detection signal input
N.C.
O
O
O
I/O
O
O
O
I
Not used (OPEN)
EE-CS
EE-CKO
EE-SIO
MD-SO
LNKOFF
UNIREQ
UNICKI
UNISI
UNISO
MD-CKO
MD-SI
N.C.
Chip select signal output for a EEPROM Not used this set (OPEN)
Serial clock signal output for a EEPROM Not used this set (OPEN)
Data signal input/output for a EEPROM Not used this set (OPEN)
Write data signal output to RF AMP (IC100), CXD2535CR (IC200) and CXD2536CR (IC500)
LINK OFF signal output for serial communications Not used this set (OPEN)
Request signal output for serial communications Not used this set (OPEN)
Clock signal (serial communications) input
I
Data signal (serial communications) input
O
O
I
Data signal (serial communications) output
Serial clock signal output to RF AMP (IC100), CXD2535CR (IC200) and CXD2536CR (IC500)
Read data signal input from CXD2535CR (IC200) and CXD2536CR (IC500)
Not used
O
I
SENS
CC-XINT
Internal status (SENS) input from CXD2535CR (IC200) and CXD2536CR (IC500)
Interruption stsatus input from CXD2536CR (IC500)
I
– 39 –
Pin No. Pin Name
I/O
Function
56
57
58
LIMIT-SW
DOOR-SW
MD-LAT
I
I
Detection signal input from the limit switch (S400) When sled limit in : "L"
Detection signal input from the door open/close switch (S620) When open : "L"
Serial latch signal output to RF AMP (IC100), CXD2535CR (IC200) and CXD2536CR (IC500)
Reset signal output to RF AMP (IC100), CXD2535CR (IC200) and CXD2536CR (IC500)
When reset "L"
O
59
MD-RST
O
60
61
BU-IN
I
I
Battery detection signal input
BUS-ON
BUS-ON detection signal (serial communications) input BUS ON : “L”
Sub-code Q sync (SCOR) input from CXD2535CR (IC200)
"L" every 13.3msec, Almost "H"
62
SQSY
I
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
STR-SW
FOK
I
Detection signal input from the STOP switch (S600)
I
Focus OK signal input from CXD2435CR (IC200) "H" is input when the focus is applied
Power control signal output (Servo system) Power ON : "H"
Deemphasis control signal output to the D/A converter (IC550) Deemphasis ON "L"
Audio mute signal output When mute : "H"
MD-ON
EMPH-O
A-MUT
N.C.
O
O
O
O
O
O
I
Not used (OPEN)
CLOCK
DATA
TM-ON/OFF
VDD
Clock signal output for test mode indication Not used this set (OPEN)
Data signal output for test mode indication Not used this set (OPEN)
Test mode set up terminal Normolly :"H" When test mode : "L"
Power supply terminal (+5V)
–
N.C.
–
Not used (Fixed at "H")
TO0
O
O
O
O
I
Test key (4x8 matrix) signal output terminal (OPEN)
Test key (4x8 matrix) signal output terminal (OPEN)
Test key (4x8 matrix) signal output terminal (OPEN)
Test key (4x8 matrix) signal output terminal (OPEN)
Test key (4x8 matrix) signal input terminal (Fixed at "L")
Test key (4x8 matrix) signal input terminal (Fixed at "L")
Test key (4x8 matrix) signal input terminal (Fixed at "L")
TO1
TO2
TO3
TI0
TI1
I
TI2
I
*1 Elevator motor (M904) control
*2 Loading motor (M903) control
Mode
Mode
UP
"H"
"L"
DOWN
"L"
IN
OUT
"H"
"L"
Brake
"H"
Terminal
Terminal
M1 pin 6
M1 pin 7
M2 pin 8
"L"
"H"
"H"
M2 pin 9
"H"
– 40 –
SECTION 4
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Color Indication of Appearrance Parts
Example:
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference num-
ber in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.
The components identified by mark
! or dotted line with mark ! are
critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque ! sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le neméro spécifié.
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
4-1. CASE SECTION
8
3
5
MG-798-133
6
9
7
17
19
10
3
CNP1
16
18
#1
15
4
7
not supplied
2
12
15
17
1
11
13
14
12
13
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
* 11
12
13
* 14
15
A-3294-228-A POWER BOARD, COMPLETE
3-930-176-01 DAMPER (798)
3-930-177-01 SPRING (FL), TENSION
3-930-173-31 CASE (LOWER)
1
2
3
4
5
X-3371-273-1 DOOR (S) ASSY(/EXP)
3-930-168-11 DOOR (P)
3-912-956-11 SCREW (2.6X6) (CU), +BVTT
4-969-961-01 EMBLEM (NO.4), SONY
X-3373-364-1 PANEL (FRONT) ASSY (/EXP)
3-931-697-01 CUSHION (STOPPER)
16
17
3-348-750-01 CUSHION (DAMPER)
3-930-744-01 SPACER (DOOR)
* 6
7
1-664-517-11 LAMP BOARD
3-909-607-01 SCREW
18
19
CNP1
3-933-740-01 SHEET (SLIDE)
3-831-441-11 CUSHION, RATTLE ABSORBER
1-776-105-11 CORD (WITH CONNECTOR) (BUS CONTROL/
RCA PIN JACK)
* 8
9
10
3-930-172-31 CASE (UPPER)
3-930-175-11 COVER (CORD)
X-3371-225-1 PANEL (REAR) ASSY (/EXP)
– 41 –
Ver 1.1
4-2. MECHANISM SECTION-1
(MG-798-133)
59
58
71
57
69
60
56
55
#2
60
#4
S902
#4
54
S903
62
M903
61
52
63
53
52
60
64
70
#2
#3
67
51
#2
#2
M904
68
65
#2
#2
66
52
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
51
52
53
* 54
55
3-930-351-01 WHEEL (ELV), WORM
* 64
65
66
67
68
X-3371-218-1 CHASSIS (BASE) ASSY
X-3371-211-1 CHASSIS (GEAR) ASSY
3-930-313-01 GEAR (ELVC)
3-931-698-01 CUSHION (ROLL L)
3-348-750-01 CUSHION (DAMPER)
3-377-719-11 WASHER, POLYETHYLENE
3-880-990-00 SCREW (1.7X3),FLAT,(+) SPECIAL
A-3294-229-A MAIN BOARD, COMPLETE
1-776-474-11 CABLE, FLAT 7P
56
57
58
59
60
1-658-887-11 MAIN FLEXIBLE BOARD
1-658-881-11 SERVO FLEXIBLE BOARD
3-909-412-01 SCREW (+P) (1.7X2) (TYPE 3)
A-3309-891-A SENSOR BOARD, COMPLETE
3-930-312-01 BEARING (ELV)
69
* 70
* 71
M903
M904
3-931-366-01 STOPPER, LEAD
3-931-149-02 SHEET (MAIN PC BOARD)
3-931-025-01 SHEET (MECHANICAL DECK)
X-3371-508-1 MOTOR ASSY (LOADING)
A-3291-505-A ELV MOTOR BLOCK ASSY (ELEVATOR)
61
62
63
X-3371-220-1 BRACKET (LD) ASSY
3-930-365-01 WHEEL (LD), WORM
3-930-317-01 GEAR (LD)
S902
S903
1-570-771-11 SWITCH (LES)
1-570-771-21 SWITCH (SES)
– 42 –
4-3. MECHANISM SECTION-2
(MG-798-133)
129
128
127
#2
#2
127
112
129
129
128
#2
110
111
112
(US, Canadian)
131
101
114
130
132
115
116
113
not supplied
130
109
126
117
108
107
106
105
104
118
119
124
120
126
125
121
122
102
101
103
123
125
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
101
102
103
104
105
3-377-719-11 WASHER, POLYETHYLENE
3-930-354-01 LEVER, DISK EJECT
3-930-350-01 SPRING (EJ), TORSION
3-930-318-51 BUTTON (EJECT)
117
118
* 119
120
3-930-366-01 RACK (LOADING)
3-930-360-01 SPRING (LIMITER), TORSION
X-3371-221-1 SLIDER ASSY, LOADING
X-3371-210-3 CHASSIS (REAR) ASSY
3-930-349-01 SPRING (LOCK), TORSION
3-930-318-41 BUTTON (EJECT)
121
106
107
108
109
110
3-930-318-31 BUTTON (EJECT)
3-930-318-21 BUTTON (EJECT)
3-930-318-11 BUTTON (EJECT)
3-930-318-01 BUTTON (EJECT)
3-930-314-01 ESCUTCHEON
122
123
124
125
* 126
X-3371-219-1 PLATE (HOLDER) ASSY, LOCK
3-331-007-21 WASHER
3-930-352-01 SPRING (D LOCK), TENSION
X-3371-216-1 HOLDER (CADDIE) ASSY
3-317-054-01 SPACER, E
111
112
* 113
* 114
* 115
3-930-319-01 BUTTON (STOP)
3-930-311-01 RETAINER (ELV)
3-930-320-01 CHASSIS (FRONT)
3-930-316-01 GUIDE (HOLDER)
X-3371-209-1 CHASSIS (TOP) ASSY
127
128
129
130
131
3-931-699-01 CUSHION (ROLL H)
9-911-840-XX CUSHION
3-348-750-01 CUSHION (DAMPER)
3-317-552-71 SCREW (M1.7)
3-891-132-00 SCREW (M1.7x2.0), SPECIAL HEAD
* 116
3-930-321-01 PLATE, HOLDER STOP
132
3-935-293-01 SHEET (COPY MD) (US, Canadian)
– 43 –
4-4. MECHANISM SECTION-3
(MG-798-133)
#6
#6
#6
159
157
158
157
156
160
155
156
155
155
161
174
163
162
RV901
#6
M901
#2
M902
165
164
154
S901
#4
167
153
152
166
#6
#2
168
#7
#5
171
169
170
172
151
#5
173
The components identified by Les composants identifiés par une
mark ! or dotted line with marque ! sont critiques pour la
mark ! are critical for safety. sécurité.
Replace only with part number Ne les remplacer que par une pièce
specified.
portant le neméro spécifié.
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
151
152
153
154
155
3-930-338-01 HOLDER (OP GUIDE B)
3-930-332-01 GUIDE (OPB)
X-3371-212-1 SCREW (ELV) ASSY, FEED
1-658-880-11 EHS FLEXIBLE BOARD
3-930-333-01 SLEEVE (ELV)
165
166
167
168
169
3-930-336-01 HOLDER (SLB)
3-930-335-01 DETENT, SL
X-3371-213-1 HOLDER (SLA) ASSY
X-3371-214-1 SCREW (SL) ASSY, FEED
3-930-331-01 GUIDE (OPA)
156
157
* 158
159
160
3-930-334-01 SPRING (ELV), COMPRESSION
3-930-345-01 PLATE (B), ELV LIMITER
X-3371-215-1 CHASSIS (OP) ASSY
3-930-344-01 PLATE (A), ELV LIMITER
3-930-711-01 SPRING (ELV2), COMPRESSION
170
!171
* 172
173
3-930-337-01 SPRING (SL OUTSERT), FEED
8-583-035-01 OPTICAL PICK UP KMS-193C/J2N
A-3222-980-A SERVO BOARD, COMPLETE
3-932-755-01 SCREW (M1.7X2.2)
174
3-930-310-01 COLLAR (EHS)
161
162
163
164
3-930-339-01 WHEEL (SL), WORM
3-338-645-31 WASHER (0.8-2.5)
3-930-343-01 SCREW (K1.7X3.5)
3-930-342-01 RETAINER (SP)
M901
M902
A-3291-507-A SP MOTOR BLOCK ASSY (SPINDLE)
A-3291-508-A SL MOTOR BLOCK ASSY (SLED)
RV901 1-223-817-11 RES, VAR, SLIDE 10K
(ELEVATOR HIGHT SENSOR)
1-570-771-21 SWITCH (HOME POSITION DETECT)
S901
– 44 –
EHS FLEXIBLE
LAMP MAIN
SECTION 5
ELECTRICAL PARTS LIST
NOTE:
The components identified by mark
! or dotted line with mark ! are
critical for safety.
• Due to standardization, replacements in the
parts list may be different from the parts speci-
fied in the diagrams or the components used on
the set.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. .
uPB. . : µPB. .
uPD. . : µPD. .
uPA. . : µPA. .
uPC. . : µPC. .
Replace only with part number
specified.
• -XX and -X mean standardized parts, so they
may have some difference from the original one.
Les composants identifiés par une
marque ! sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le neméro spécifié.
• CAPACITORS
uF: µF
• RESISTORS
All resistors are in ohms.
• COILS
uH: µH
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when order-
ing these items.
When indicating parts by reference
number, please include the board.
Ref. No.
Part No.
Description
Remark Ref. No.
Part No.
Description
Remark
C509
C510
1-165-128-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
0.22uF
0.1uF
16V
16V
1-658-880-11 EHS FLEXIBLE BOARD
10%
******************
C511
C512
C513
C520
C521
1-162-927-11 CERAMIC CHIP
1-165-128-11 CERAMIC CHIP
1-162-927-11 CERAMIC CHIP
1-162-925-11 CERAMIC CHIP
1-135-259-11 TANTAL. CHIP
100PF 5%
0.22uF
100PF 5%
50V
16V
50V
50V
6.3V
< VARIABLE RESISTOR >
RV901 1-223-817-11 RES, VAR, SLIDE 10K
(ELEVATOR HIGHT SENSOR)
68PF
5%
10uF
20%
< SWITCH >
C550
C551
C553
C554
C557
1-104-852-11 TANTAL. CHIP
1-107-826-11 CERAMIC CHIP
1-164-357-11 CERAMIC CHIP
1-165-128-11 CERAMIC CHIP
1-164-004-11 CERAMIC CHIP
22uF
0.1uF
1000PF 5%
0.22uF
0.1uF
20%
10%
10V
16V
50V
16V
25V
S901
1-570-771-21 SWITCH (HOME POSITION DETECT)
*************************************************************
*
1-664-517-11 LAMP BOARD
10%
***********
C560
C600
C601
C602
C603
1-135-259-11 TANTAL. CHIP
1-104-852-11 TANTAL. CHIP
1-165-128-11 CERAMIC CHIP
1-164-489-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
10uF
22uF
0.22uF
0.22uF 10%
20%
20%
6.3V
10V
16V
16V
16V
< CONNECTOR >
* CN620 1-580-056-21 PIN, CONNECTOR 3P
< PILOT LAMP >
0.1uF
10%
C604
C605
C607
C608
C609
1-107-826-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
1-162-927-11 CERAMIC CHIP
1-162-917-11 CERAMIC CHIP
1-162-917-11 CERAMIC CHIP
0.1uF
0.1uF
100PF 5%
15PF
15PF
10%
10%
16V
16V
50V
50V
50V
PL620 1-517-492-11 LAMP, PILOT (ILLUMINATION)
< RESISTOR >
5%
5%
R620
1-216-298-00 METAL CHIP
< SWITCH >
2.2
5%
1/10W
C610
C611
C620
C621
C650
1-107-826-11 CERAMIC CHIP
1-165-128-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
1-165-128-11 CERAMIC CHIP
0.1uF
0.22uF
0.1uF
0.1uF
0.22uF
10%
16V
16V
16V
16V
16V
10%
10%
S620
1-692-532-21 SWITCH, PUSH (1 KEY)
(DOOR OPEN/CLOSE DET)
*************************************************************
C651
C652
C653
C700
C701
1-165-128-11 CERAMIC CHIP
1-165-128-11 CERAMIC CHIP
1-165-128-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
0.22uF
0.22uF
0.22uF
0.1uF
16V
16V
16V
16V
16V
*
A-3294-229-A MAIN BOARD, COMPLETE
*********************
10%
10%
< CAPACITOR >
0.1uF
C500
C501
C503
C504
C505
1-165-128-11 CERAMIC CHIP
1-128-361-11 ELECT CHIP
1-162-970-11 CERAMIC CHIP
1-162-910-11 CERAMIC CHIP
1-165-128-11 CERAMIC CHIP
0.22uF
470uF 20%
0.01uF 10%
5PF
16V
10V
25V
< CONNECTOR >
CN500 1-573-370-21 CONNECTOR, FFC/FPC 30P
0.25PF 50V
16V
* CN600 1-573-939-11 CONNECTOR, FFC/FPC (ZIF) 30P
CN601 1-573-916-11 CONNECTOR, FFC/FPC (ZIF) 7P
CN602 1-580-055-21 PIN, CONNECTOR 2P
0.22uF
C506
C507
C508
1-135-259-11 TANTAL. CHIP
1-107-826-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
10uF
0.1uF
0.1uF
20%
10%
10%
6.3V
16V
16V
CN603 1-580-055-21 PIN, CONNECTOR 2P
– 45 –
MAIN
Ref. No.
Part No.
Description
Remark Ref. No.
R504
Part No.
Description
Remark
1/16W
* CN604 1-580-056-21 PIN, CONNECTOR 3P
CN700 1-580-055-21 PIN, CONNECTOR 2P
CN701 1-580-055-21 PIN, CONNECTOR 2P
1-216-809-11 METAL CHIP
100
5%
R505
R506
R520
R521
R550
1-218-733-11 METAL CHIP
1-218-730-11 METAL CHIP
1-216-811-11 METAL CHIP
1-218-664-11 METAL CHIP
1-216-797-11 METAL CHIP
51K
39K
150
68
0.50% 1/16W
0.50% 1/16W
1/16W
0.50% 1/16W
< DIODE >
5%
D502
D560
D561
D562
D600
8-719-421-36 DIODE MA8036-L
8-719-988-62 DIODE 1SS355
8-719-988-62 DIODE 1SS355
8-719-988-62 DIODE 1SS355
8-719-422-64 DIODE MA8062-M
10
5%
1/16W
R551
R552
R553
R560
R561
1-216-809-11 METAL CHIP
1-216-809-11 METAL CHIP
1-216-825-11 METAL CHIP
1-218-692-11 METAL CHIP
1-218-716-11 METAL CHIP
100
100
2.2K
1K
5%
5%
5%
1/16W
1/16W
1/16W
0.50% 1/16W
0.50% 1/16W
< FERRITE BEAD >
10K
FB510 1-414-235-11 INDUCTOR, FERRITE BEAD
FB650 1-500-235-21 BEAD, FERRITE (CHIP)
FB651 1-500-235-21 BEAD, FERRITE (CHIP)
R600
R601
R602
R603
R605
1-216-841-11 METAL CHIP
1-216-845-11 METAL CHIP
1-216-845-11 METAL CHIP
1-216-845-11 METAL CHIP
1-216-845-11 METAL CHIP
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
100K
100K
100K
100K
< IC >
IC500
IC501
IC550
IC600
IC601
8-752-371-17 IC CXD2536R
R607
R608
R609
R610
R611
1-218-708-11 METAL CHIP
1-216-821-11 METAL CHIP
1-216-825-11 METAL CHIP
1-216-821-11 METAL CHIP
1-216-825-11 METAL CHIP
4.7K
1K
2.2K
1K
2.2K
0.50% 1/16W
8-759-341-28 IC HM51W4400TT6-8
8-759-425-18 IC CS4330-KSR-H
8-752-882-94 IC CXP84340-043Q
8-759-363-81 IC XC61AN4002PR
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
IC602
IC700
IC701
8-759-238-47 IC TC74HCT7007AF(EL)
8-759-823-87 IC LB1638M
8-759-823-87 IC LB1638M
R612
R613
R614
R615
R616
1-216-845-11 METAL CHIP
1-216-821-11 METAL CHIP
1-216-825-11 METAL CHIP
1-216-821-11 METAL CHIP
1-216-825-11 METAL CHIP
100K
1K
2.2K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
< COIL >
2.2K
L500
L501
L502
L600
1-412-058-11 INDUCTOR CHIP 10uH
1-410-998-31 INDUCTOR CHIP 2.7uH
1-412-058-11 INDUCTOR CHIP 10uH
1-412-058-11 INDUCTOR CHIP 10uH
R617
R618
R619
R622
R624
1-216-845-11 METAL CHIP
1-216-845-11 METAL CHIP
1-216-833-11 METAL CHIP
1-216-809-11 METAL CHIP
1-216-821-11 METAL CHIP
100K
100K
10K
100
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
< FILTER >
R625
R626
R627
R628
R629
1-216-845-11 METAL CHIP
1-216-845-11 METAL CHIP
1-216-821-11 METAL CHIP
1-216-845-11 METAL CHIP
1-216-845-11 METAL CHIP
100K
100K
1K
100K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
NF650 1-239-466-21 FILTER, EMI
NF651 1-239-581-21 FILTER, EMI
< TRANSISTOR >
Q500
Q501
Q560
Q561
Q600
8-729-020-67 TRANSISTOR XN1A312-TX
8-729-920-21 TRANSISTOR DTC314TKH04
8-729-424-59 TRANSISTOR UN2212
8-729-421-22 TRANSISTOR UN2211
8-729-904-60 TRANSISTOR DTB113ZK
R630
R631
R632
R633
R634
1-216-841-11 METAL CHIP
1-216-821-11 METAL CHIP
1-216-821-11 METAL CHIP
1-216-821-11 METAL CHIP
1-216-833-11 METAL CHIP
47K
1K
1K
1K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
Q601
8-729-421-22 TRANSISTOR UN2211
< RESISTOR >
R636
1-216-864-11 METAL CHIP
0
5%
1/16W
< COMPOSITION CIRCUIT BLOCK >
R500
R501
R502
R503
1-216-821-11 METAL CHIP
1-216-815-11 METAL CHIP
1-216-827-11 METAL CHIP
1-216-809-11 METAL CHIP
1K
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
RB600 1-239-517-11 RESISTOR, NETWORK (1608) 100Kx4
RB601 1-239-517-11 RESISTOR, NETWORK (1608) 100Kx4
RB602 1-239-514-11 RESISTOR, NETWORK (1608) 100Kx4
RB603 1-239-516-11 RESISTOR, NETWORK (1608) 1Kx4
330
3.3K
100
– 46 –
MAIN POWER
Ref. No.
Part No.
Description
Remark Ref. No.
Part No.
Description
Remark
C932
C940
C941
C942
1-164-004-11 CERAMIC CHIP
1-164-004-11 CERAMIC CHIP
1-110-474-11 SOLID CHIP
1-164-004-11 CERAMIC CHIP
0.1uF
0.1uF
10uF
0.1uF
10%
10%
20%
10%
25V
25V
50V
25V
RB604 1-239-516-11 RESISTOR, NETWORK (1608) 1Kx4
RB605 1-239-517-11 RESISTOR, NETWORK (1608) 100Kx4
RB606 1-239-516-11 RESISTOR, NETWORK (1608) 1Kx4
RB607 1-239-516-11 RESISTOR, NETWORK (1608) 1Kx4
RB609 1-239-516-11 RESISTOR, NETWORK (1608) 1Kx4
C950
C951
C952
C953
C954
1-163-125-00 CERAMIC CHIP
1-163-275-11 CERAMIC CHIP
1-163-263-11 CERAMIC CHIP
1-163-275-11 CERAMIC CHIP
1-163-263-11 CERAMIC CHIP
220PF 5%
0.001uF 5%
330PF 5%
0.001uF 5%
330PF 5%
50V
50V
50V
50V
50V
< SWITCH >
S600
1-571-914-21 SWITCH, KEY BOARD (STOP)
< THERMISTOR >
C955
C956
C957
C958
C959
1-110-456-11 SOLID CHIP
1-128-590-11 ELECT CHIP
1-128-590-11 ELECT CHIP
1-164-004-11 CERAMIC CHIP
1-110-447-11 SOLID CHIP
47uF
100uF 20%
100uF 20%
0.1uF
22uF
20%
16V
6.3V
6.3V
25V
6.3V
TH600 1-810-421-11 THERMISTOR NTH5G36B103K01TE 10K
< VIBRATOR >
10%
20%
C960
C961
C962
C963
C970
1-128-590-11 ELECT CHIP
1-128-590-11 ELECT CHIP
1-164-004-11 CERAMIC CHIP
1-164-004-11 CERAMIC CHIP
1-163-275-11 CERAMIC CHIP
100uF 20%
100uF 20%
6.3V
6.3V
25V
25V
50V
X500
X600
X601
1-760-168-11 VIBRATOR, CRYSTAL (45.1584MHz)
1-760-365-11 VIBRATOR, CERAMIC (10MHz)
1-579-886-21 VIBRATOR, CRYSTAL (32.768KHz)
0.1uF
10%
0.1uF
10%
*************************************************************
0.001uF 5%
*
A-3294-228-A POWER BOARD, COMPLETE
< CONNECTOR >
***********************
* CN800 1-573-939-11 CONNECTOR, FFC/FPC (ZIF) 30P
< CAPACITOR >
CN900 1-764-585-11 PIN, CONNECTOR (PC BOARD) 12P
C800
C801
C803
C805
C810
1-110-456-11 SOLID CHIP
1-164-004-11 CERAMIC CHIP
1-164-004-11 CERAMIC CHIP
1-110-450-11 SOLID CHIP
1-110-457-11 SOLID CHIP
47uF
0.1uF
0.1uF
100uF 20%
3.3uF 20%
20%
10%
10%
16V
25V
25V
6.3V
25V
< DIODE >
D900
D901
D902
D910
D911
8-719-422-64 DIODE MA8062-M
8-719-422-64 DIODE MA8062-M
8-719-975-40 DIODE RB411D
8-719-977-12 DIODE DTZ6.8B
8-719-400-20 DIODE MA152WA
C811
C812
C813
C814
C815
1-163-251-11 CERAMIC CHIP
1-110-474-11 SOLID CHIP
1-110-457-11 SOLID CHIP
1-163-125-00 CERAMIC CHIP
1-163-125-00 CERAMIC CHIP
100PF 5%
10uF
3.3uF
220PF 5%
220PF 5%
50V
50V
25V
50V
50V
20%
20%
D912
D920
D921
D930
D940
8-719-988-62 DIODE 1SS355
8-719-422-64 DIODE MA8062-M
8-719-988-62 DIODE 1SS355
8-719-422-16 DIODE MA8039-L-TX
8-719-422-97 DIODE MA8091-M
C820
C821
C822
C823
C824
1-110-457-11 SOLID CHIP
1-163-251-11 CERAMIC CHIP
1-110-474-11 SOLID CHIP
1-110-457-11 SOLID CHIP
1-163-125-00 CERAMIC CHIP
3.3uF
100PF 5%
10uF
3.3uF
20%
25V
50V
50V
25V
50V
20%
20%
D950
D951
D952
8-719-975-33 DIODE RB110C
8-719-422-16 DIODE MA8039-L-TX
8-719-975-33 DIODE RB110C
220PF 5%
C825
C900
C901
C902
C903
1-163-125-00 CERAMIC CHIP
1-163-017-00 CERAMIC CHIP
1-164-004-11 CERAMIC CHIP
1-163-275-11 CERAMIC CHIP
1-110-456-11 SOLID CHIP
220PF 5%
0.0047uF5%
50V
50V
25V
50V
16V
< FERRITE BEAD >
0.1uF
10%
FB810 1-414-598-11 INDUCTOR, FERRITE BEAD
FB820 1-414-598-11 INDUCTOR, FERRITE BEAD
0.001uF 5%
47uF
20%
< IC >
C904
C909
C910
C911
C920
1-164-505-11 CERAMIC CHIP
1-164-004-11 CERAMIC CHIP
1-164-004-11 CERAMIC CHIP
1-125-710-11 CAPACITOR
1-164-346-11 CERAMIC CHIP
2.2uF
0.1uF
0.1uF
0.1F
16V
25V
25V
5.5V
16V
10%
10%
IC800
IC900
IC950
8-759-711-82 IC NJM4580E
8-759-284-87 IC MM1284XFFE
8-759-370-13 IC TL1451ACDB-E20
1uF
C931
1-110-446-11 SOLID CHIP
10uF
20%
6.3V
– 47 –
Ver 1.1
POWER SENSOR
Ref. No.
Part No.
Description
< COIL >
Remark Ref. No.
Part No.
Description
Remark
1/10W
R921
R922
1-216-085-00 METAL CHIP
1-216-097-00 METAL GLAZE
33K
100K
5%
5%
1/10W
L950
L951
L952
L953
L954
1-409-640-21 COIL, CHIP CHOKE
1-403-584-11 COIL, CHIP CHOKE
1-409-640-21 COIL, CHIP CHOKE
1-403-584-11 COIL, CHIP CHOKE
1-409-640-21 COIL, CHIP CHOKE
10uH
33uH
10uH
33uH
10uH
R930
R931
R940
R950
R951
1-216-057-00 METAL CHIP
1-216-057-00 METAL CHIP
1-216-049-00 METAL GLAZE
1-216-073-00 METAL CHIP
1-216-065-00 METAL CHIP
2.2K
2.2K
1K
10K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< FILTER >
R952
R953
R954
R955
R956
1-216-065-00 METAL CHIP
1-216-067-00 METAL CHIP
1-216-077-00 METAL CHIP
1-216-077-00 METAL CHIP
1-216-085-00 METAL CHIP
4.7K
5.6K
15K
15K
33K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
NF900 1-239-466-21 FILTER, EMI
< IC LINK >
PS900 1-533-397-11 LINK, CHIP IC (ICB-S2.3)
< TRANSISTOR >
R957
R958
R959
R960
R961
1-216-085-00 METAL CHIP
1-216-085-00 METAL CHIP
1-216-085-00 METAL CHIP
1-216-025-00 METAL GLAZE
1-216-045-00 METAL CHIP
33K
33K
33K
100
680
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Q800
Q810
Q820
Q910
Q911
8-729-424-12 TRANSISTOR UN2112
8-729-920-21 TRANSISTOR DTC314TKH04
8-729-920-21 TRANSISTOR DTC314TKH04
8-729-920-85 TRANSISTOR 2SD1664-QR
8-729-422-27 TRANSISTOR 2SD601A-Q
R962
R963
R964
R965
R966
1-216-045-00 METAL CHIP
1-216-675-11 METAL CHIP
1-216-663-11 METAL CHIP
1-216-025-00 METAL GLAZE
1-216-025-00 METAL GLAZE
680
10K
3.3K
100
100
5%
1/10W
0.5% 1/10W
0.5% 1/10W
5%
5%
Q920
Q921
Q931
Q940
Q941
8-729-422-27 TRANSISTOR 2SD601A-Q
8-729-424-12 TRANSISTOR UN2112
8-729-920-85 TRANSISTOR 2SD1664-QR
8-729-020-67 TRANSISTOR XN1A312-TX
8-729-920-85 TRANSISTOR 2SD1664-QR
1/10W
1/10W
R967
R968
R969
R970
R980
1-216-045-00 METAL CHIP
1-216-045-00 METAL CHIP
1-216-675-11 METAL CHIP
1-216-663-11 METAL CHIP
1-216-841-11 METAL CHIP
680
680
10K
3.3K
47K
5%
5%
1/10W
1/10W
0.5% 1/10W
0.5% 1/10W
5%
Q950
Q952
Q953
Q954
8-729-106-60 TRANSISTOR 2SB1115A
8-729-822-84 TRANSISTOR 2SB1202FAST
8-729-920-85 TRANSISTOR 2SD1664-QR
8-729-106-60 TRANSISTOR 2SB1115A
1/16W
*************************************************************
A-3309-891-A SENSOR BOARD, COMPLETE
< RESISTOR >
************************
R800
R801
R811
R812
R813
1-216-057-00 METAL CHIP
1-216-057-00 METAL CHIP
1-208-561-11 METAL GLAZE
1-216-238-00 METAL GLAZE
1-208-561-11 METAL GLAZE
2.2K
2.2K
27K
47K
27K
5%
5%
2%
2%
2%
1/10W
1/10W
1/8W
1/8W
1/8W
For the parts on the SENSOR board, replace the entire mounted board.
*************************************************************
R814
R815
R816
R821
R822
1-216-238-00 METAL GLAZE
1-216-182-00 METAL GLAZE
1-216-246-00 METAL GLAZE
1-208-561-11 METAL GLAZE
1-216-238-00 METAL GLAZE
47K
220
100K
27K
47K
2%
2%
2%
2%
2%
1/8W
1/8W
1/8W
1/8W
1/8W
R823
R824
R825
R826
R900
1-208-561-11 METAL GLAZE
1-216-238-00 METAL GLAZE
1-216-182-00 METAL GLAZE
1-216-246-00 METAL GLAZE
1-216-089-00 METAL GLAZE
27K
47K
220
100K
47K
2%
2%
2%
2%
5%
1/8W
1/8W
1/8W
1/8W
1/10W
R910
R911
R920
1-216-081-00 METAL CHIP
1-216-049-00 METAL GLAZE
1-216-089-00 METAL GLAZE
22K
1K
47K
5%
5%
5%
1/10W
1/10W
1/10W
– 48 –
SERVO
Ref. No.
Part No.
Description
Remark Ref. No.
Part No.
Description
< IC >
Remark
*
A-3222-980-A SERVO BOARD, COMPLETE
*********************
IC100
IC200
IC201
8-752-072-68 IC CXA1981AR
8-752-382-23 IC CXD2535CR-1
8-759-031-84 IC SC7S04F
< CAPACITOR >
C102
C103
C104
C105
C106
1-135-259-11 TANTAL. CHIP
1-135-259-11 TANTAL. CHIP
1-162-964-11 CERAMIC CHIP
1-162-969-11 CERAMIC CHIP
1-164-227-11 CERAMIC CHIP
10uF
10uF
0.001uF 10%
0.0068uF10%
0.022uF 10%
20%
20%
6.3V
IC300
8-759-442-80 IC MPC17A38ZVMEL
6.3V
50V
25V
25V
< COIL >
L100
L200
L300
L301
L302
1-412-058-11 INDUCTOR CHIP 10uH
1-412-058-11 INDUCTOR CHIP 10uH
C107
C108
C111
C113
C114
1-162-970-11 CERAMIC CHIP
1-162-970-11 CERAMIC CHIP
1-104-852-11 TANTAL. CHIP
1-107-826-11 CERAMIC CHIP
1-162-970-11 CERAMIC CHIP
0.01uF 10%
0.01uF 10%
22uF
0.1uF
0.01uF 10%
25V
25V
6.3V
16V
25V
1-412-637-51 INDUCTOR
330uH
1-412-039-51 INDUCTOR CHIP 100uH
1-412-039-51 INDUCTOR CHIP 100uH
20%
10%
L303
L304
1-412-039-51 INDUCTOR CHIP 100uH
1-412-039-51 INDUCTOR CHIP 100uH
C115
C117
C118
C119
C120
1-109-982-11 CERAMIC CHIP
1-109-982-11 CERAMIC CHIP
1-162-968-11 CERAMIC CHIP
1-162-969-11 CERAMIC CHIP
1-165-176-11 CERAMIC CHIP
1uF
1uF
0.0047uF10%
0.0068uF10%
0.047uF 10%
10%
10%
10V
10V
50V
25V
16V
< TRANSISTOR >
Q100
Q200
8-729-216-22 TRANSISTOR 2SA1162-G
8-729-422-27 TRANSISTOR 2SD601A-Q
C123
C200
C202
C204
C205
1-107-826-11 CERAMIC CHIP
1-109-982-11 CERAMIC CHIP
1-135-259-11 TANTAL. CHIP
1-162-970-11 CERAMIC CHIP
1-107-823-11 CERAMIC CHIP
0.1uF
1uF
10uF
0.01uF 10%
0.47uF 10%
10%
10%
20%
16V
10V
6.3V
25V
16V
< RESISTOR >
R100
R101
R102
R103
R104
1-216-841-11 METAL CHIP
1-216-308-00 METAL CHIP
1-216-811-11 METAL CHIP
1-216-853-11 METAL CHIP
1-216-829-11 METAL CHIP
47K
4.7
150
470K
4.7K
5%
5%
5%
5%
5%
1/16W
1/10W
1/16W
1/16W
1/16W
C206
C207
C208
C209
C210
1-162-927-11 CERAMIC CHIP
1-162-979-11 CERAMIC CHIP
1-162-587-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
100PF 5%
0.0027uF10%
0.039uF 10%
0.1uF
0.1uF
50V
50V
25V
16V
16V
R106
R107
R108
R109
R110
1-216-853-11 METAL CHIP
1-216-825-11 METAL CHIP
1-216-825-11 METAL CHIP
1-216-825-11 METAL CHIP
1-216-835-11 METAL CHIP
470K
2.2K
2.2K
2.2K
15K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
10%
10%
C211
C301
C302
C303
C304
1-107-826-11 CERAMIC CHIP
1-109-982-11 CERAMIC CHIP
1-109-982-11 CERAMIC CHIP
1-104-852-11 TANTAL. CHIP
1-109-982-11 CERAMIC CHIP
0.1uF
1uF
1uF
22uF
1uF
10%
10%
10%
20%
10%
16V
10V
10V
10V
10V
R111
R201
R202
R203
R207
1-216-841-11 METAL CHIP
1-216-809-11 METAL CHIP
1-216-809-11 METAL CHIP
1-216-809-11 METAL CHIP
1-216-833-11 METAL CHIP
47K
100
100
100
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
C305
C306
C307
1-109-982-11 CERAMIC CHIP
1-107-682-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
1uF
1uF
0.1uF
10%
10%
10%
10V
16V
16V
R208
R209
R210
R211
R212
1-216-845-11 METAL CHIP
1-216-857-11 METAL CHIP
1-216-827-11 METAL CHIP
1-218-270-11 METAL GLAZE
1-216-822-11 METAL CHIP
100K
1M
3.3K
1.1K
1.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
< CONNECTOR >
CN100 1-573-931-11 CONNECTOR, FFC/FPC (ZIF) 22P
CN200 1-573-370-21 CONNECTOR, FFC/FPC 30P
CN301 1-580-055-21 PIN, CONNECTOR 2P
R221
R222
R223
R224
1-216-853-11 METAL CHIP
1-216-819-11 METAL CHIP
1-216-821-11 METAL CHIP
1-216-821-11 METAL CHIP
470K
680
1K
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
CN400 1-573-346-21 CONNECTOR, FFC/FPC 6P
< DIODE >
1K
D300
D301
8-719-988-62 DIODE 1SS355
8-719-988-62 DIODE 1SS355
< COMPOSITION CIRCUIT BLOCK >
RB201 1-233-576-11 RES, CHIP NETWORK 100x4
RB202 1-233-576-11 RES, CHIP NETWORK 100x4
– 49 –
MDX-61
SERVO
Ref. No.
Part No.
Description
Remark Ref. No.
Part No.
Description
Remark
RB203 1-233-576-11 RES, CHIP NETWORK 100x4
< SWITCH >
MOUNTING HARDWARE
*******************
501
502
503
504
506
3-930-163-01 BASE (FITTING)
X-3371-178-1 BRACKET ASSY
7-682-961-01 SCREW +PSW 4X8
4-304-511-00 NUT (M5), FLANGE
3-930-166-01 CUSHION (FITTING)
S400
1-692-532-21 SWITCH, PUSH (1 KEY) (LIMIT DET)
*************************************************************
MISCELLANEOUS
**************
509
510
1-590-519-21 CORD (WITH CONNECTOR) (BUS CABLE 5.5m)
1-777-284-11 CORD, CONNECTION (RCA PIN CORD 5.5m)
55
56
57
154
!171
1-776-474-11 CABLE, FLAT 7P
1-658-887-11 MAIN FLEXIBLE BOARD
1-658-881-11 SERVO FLEXIBLE BOARD
1-658-880-11 EHS FLEXIBLE BOARD
8-583-035-01 OPTICAL PICK UP KMS-193C/J2N
CNP1
1-776-105-11 CORD (WITH CONNECTOR)
(BUS CONTROL/RCA PIN JACK)
M901
M902
M903
M904
A-3291-507-A SP MOTOR BLOCK ASSY (SPINDLE)
A-3291-508-A SL MOTOR BLOCK ASSY (SLED)
X-3371-508-1 MOTOR ASSY (LOADING)
A-3291-505-A ELV MOTOR BLOCK ASSY (ELEVATOR)
RV901 1-223-817-11 RES, VAR, SLIDE 10K
(ELEVATOR HIGHT SENSOR)
1-570-771-21 SWITCH (HOME POSITION DETECT)
S901
S902
S903
1-570-771-11 SWITCH (LES)
1-570-771-21 SWITCH (SES)
*************************************************************
**************
HARDWARE LIST
**************
#1
#2
#3
#4
#5
7-685-793-09 SCREW +PTT 2.6X8 (S)
7-627-852-37 PRECISION SCREW +P 1.7X1.8 TYPE3
7-627-554-07 SCREW,PRECISION +P 2X2.2
7-627-855-07 SCREW,PRECISION +P 2X5.5 TYPE3
7-627-852-27 +P 1.7X3
#6
#7
7-627-552-18 SCREW,PRECISION +P 1.7X1.6
7-627-852-58 SCREW,PRECISION +P 1.7X5 TYPE3
*************************************************************
ACCESSORIES & PACKING MATERIALS
********************************
3-859-134-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH,
GERMAN,ITALIAN) (AEP,UK,German)
3-859-134-21 MANUAL, INSTRUCTION (DUTCH,SWEDISH,
PORTUGUESE,SPANISH) (AEP,UK)
3-859-134-31 MANUAL, INSTRUCTION (ENGLISH,FRENCH,
SPANISH,CHINESE) (US,Canadian,E)
*************************************************************
The components identified by Les composants identifiés par une
mark ! or dotted line with marque ! sont critiques pour la
mark ! are critical for safety. sécurité.
Replace only with part number Ne les remplacer que par une pièce
specified.
portant le neméro spécifié.
– 50 –
MDX-61
MEMO
– 51 –
MDX-61
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.
1.1
Date
Description of Revision
Correction-1 is included.
2001.08
1.0
1998.01
1997.01
Correction-1
New
|