Click
Handycam Handbook
DCR-SR37E/SR38E/SR47E/SR48E/SR57E/
SR67E/SR77E/SR87E
2009 Sony Corporation
4-124-311-12(1)
GB
Table of contents
Using the Handycam Handbook............................................. . . . . . . . . . . . . . . . . . . . . . 2
Searching for information quickly................................... . . . . . . . . . . . . . . . . . . . . . 2
Useful recording techniques.................................................. . . . . . . . . . . . . . . . . . . . . . 6
Parts and controls.. . . . . . . . . . . .................................................. . . . . . . . . . . . . . . . . . . . . . . 7
Screen indicators.. . .................................................... . . . . . . . . . . . . . . . . . . . . . 8
Using the HOME MENU............................................ . . . . . . . . . . . . . . . . . . . 10
Using the OPTION MENU.......................................... . . . . . . . . . . . . . . . . . . . 10
Menu lists.. . . . . . . . . . . . . . . . . . . . . .................................................. . . . . . . . . . . . . . . . . . . . . 11
List of the HOME MENU........................................... . . . . . . . . . . . . . . . . . . . . 11
List of the OPTION MENU......................................... . . . . . . . . . . . . . . . . . . . . 12
Read this before operating your camcorder.............................. . . . . . . . . . . . . . . . . . . . . 13
Notes on using the Hard Disk Drive Handycam.................. . . . . . . . . . . . . . . . . . . . 14
Step 1: Charging the battery pack.......................................... . . . . . . . . . . . . . . . . . . . . 16
Step 2: Turning the power on, and setting the date and time......... . . . . . . . . . . . . . . . . . . . 19
Changing the language setting...................................... . . . . . . . . . . . . . . . . . . . 20
Five pieces of advice for successful recording............................ . . . . . . . . . . . . . . . . . . . . 21
.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................................... . . . . . . . . . . . . . . . . . . . 22
Recording movies.. . .................................................. . . . . . . . . . . . . . . . . . . . . 22
Shooting photos.. . . ................................................... . . . . . . . . . . . . . . . . . . . . 23
Playing movies.. . . . . .................................................... . . . . . . . . . . . . . . . . . . . 25
Viewing photos.. . . . ................................................... . . . . . . . . . . . . . . . . . . . . 26
Recording.. . . . . . . . . . . . . . . . . . . . .................................................... . . . . . . . . . . . . . . . . . . . 28
Recording movies.. . .................................................. . . . . . . . . . . . . . . . . . . . . 28
Shooting photos.. . . ................................................... . . . . . . . . . . . . . . . . . . . . 30
Useful functions for recording movies and photos...................... . . . . . . . . . . . . . . . . . . . 32
Zooming.. . . . . . . . . . . . . ................................................... . . . . . . . . . . . . . . . . . . . . 32
(DCR-SR57E/SR67E/SR77E/SR87E)................................... . . . . . . . . . . . . . . . . . . . 33
Adjusting the exposure for backlit subjects....................... . . . . . . . . . . . . . . . . . . . 33
Recording in mirror mode............................................ . . . . . . . . . . . . . . . . . . . 34
Switching the screen display......................................... . . . . . . . . . . . . . . . . . . . 34
Playback on the camcorder.................................................. . . . . . . . . . . . . . . . . . . . . 35
Playing movies.. . . . . .................................................... . . . . . . . . . . . . . . . . . . . 35
ꢁ
Viewing photos.. . . . ................................................... . . . . . . . . . . . . . . . . . . . . 36
Useful functions for playing movies and photos........................ . . . . . . . . . . . . . . . . . . . . 38
Searching for desired scene by pinpoint (Film Roll Index)..... . . . . . . . . . . . . . . . . . . . 38
Searching for desired scene by face (Face Index)............... . . . . . . . . . . . . . . . . . . . . 38
Searching for desired images by date (Date Index).............. . . . . . . . . . . . . . . . . . . . 39
Using PB zoom with photos.......................................... . . . . . . . . . . . . . . . . . . . 40
Playing back a series of photos (Slide show)...................... . . . . . . . . . . . . . . . . . . . 41
Playing images on a TV.. . . . .................................................. . . . . . . . . . . . . . . . . . . . . 42
Deleting movies and photos.................................................. . . . . . . . . . . . . . . . . . . . 44
Capturing a photo from a movie............................................ . . . . . . . . . . . . . . . . . . . . 46
“Memory Stick PRO Duo”media............................................ . . . . . . . . . . . . . . . . . . . . 47
Dubbing movies.. . . . ................................................... . . . . . . . . . . . . . . . . . . . 47
Copying photos.. . . . ................................................... . . . . . . . . . . . . . . . . . . . . 48
Protecting recorded movies and photos (Protect)....................... . . . . . . . . . . . . . . . . . . . 49
Dividing a movie.. . . . . . . . . . . . .................................................. . . . . . . . . . . . . . . . . . . . . 50
Using the Playlist of movies.................................................. . . . . . . . . . . . . . . . . . . . . 51
Creating the Playlist .................................................. . . . . . . . . . . . . . . . . . . . . 51
Playing the Playlist.. ................................................... . . . . . . . . . . . . . . . . . . . 52
Creating a disc with a DVD writer, recorder............................... . . . . . . . . . . . . . . . . . . . . 53
Creating a disc with a recorder, etc.................................. . . . . . . . . . . . . . . . . . . . 56
Checking the battery information.......................................... . . . . . . . . . . . . . . . . . . . . 58
Changing the recording media............................................. . . . . . . . . . . . . . . . . . . . . 59
Selecting the recording media...................................... . . . . . . . . . . . . . . . . . . . . 59
Selecting the recording media for photos......................... . . . . . . . . . . . . . . . . . . . 59
Inserting “Memory Stick PRO Duo”media........................ . . . . . . . . . . . . . . . . . . . . 59
Checking the media information............................................ . . . . . . . . . . . . . . . . . . . 61
Deleting all movies and photos (Formatting)............................. . . . . . . . . . . . . . . . . . . . 62
Preventing data on the internal hard disk from being recovered.... . . . . . . . . . . . . . . . . . . . . 63
MOVIE SETTINGS (Items for recording movies).......................... . . . . . . . . . . . . . . . . . . . . 64
PHOTO SETTINGS (Items for recording photos)........................... . . . . . . . . . . . . . . . . . . . 68
VIEW IMAGES SET (Items to customize the display)...................... . . . . . . . . . . . . . . . . . . . 70
SOUND/DISP SET (Items to adjust the sound and the screen)......... . . . . . . . . . . . . . . . . . . . 72
OUTPUT SETTINGS (Items for when connected to a TV)............... . . . . . . . . . . . . . . . . . . . . 74
CLOCK/ LANG (Items to set clock and language)...................... . . . . . . . . . . . . . . . . . . . 75
ꢂ
GENERAL SET (Other setup items)........................................... . . . . . . . . . . . . . . . . . . . 76
Functions set in the OPTION MENU..................................... . . . . . . . . . . . . . . . . . . . . 78
Troubleshooting.. . . . . . . . ................................................... . . . . . . . . . . . . . . . . . . . . 85
Self-diagnosis display/Warning indicators....................... . . . . . . . . . . . . . . . . . . . . 89
Recording time of movies/number of recordable photos............. . . . . . . . . . . . . . . . . . . . . 93
Expected recording time of movies................................ . . . . . . . . . . . . . . . . . . . . 94
Expected number of recordable photos........................... . . . . . . . . . . . . . . . . . . . 95
Using your camcorder abroad................................................ . . . . . . . . . . . . . . . . . . . 96
“Memory Stick PRO Duo”media............................................ . . . . . . . . . . . . . . . . . . . . 98
Maintenance and precautions................................................ . . . . . . . . . . . . . . . . . . . 99
About the “Memory Stick”media................................... . . . . . . . . . . . . . . . . . . . . 99
About the “InfoLITHIUM”battery pack............................. . . . . . . . . . . . . . . . . . . 100
About handling of your camcorder................................ . . . . . . . . . . . . . . . . . . . 101
Index.. . . . . . . . . . . . . . . . . . . . . . . . . . ................................................... . . . . . . . . . . . . . . . . . . . 105
ꢃ
Parts and controls
camcorder is reading or writing data.
Figures in ( ) are reference pages.
Battery pack (16)
BATT (battery) release lever (17)
(Movie)/ (Photo) lamps (19)
MODE button (24, 30)
START/STOP button (23, 29)
Hook for a shoulder belt
Tripod receptacle
Attach a tripod (sold separately) to the
tripod receptacle using a tripod screw (sold
separately: the length of the screw must be less
than 5.5 mm (7/32 in.)).
Speaker
Built-in microphone (33)
Lens (Carl Zeiss lens) (15)
LENS COVER switch (22, 23, 28, 30)
A/V Remote Connector (42, 56)
LCD screen/Touch panel (10, 34)
If you rotate the LCD panel 180 degrees, you
can close the LCD panel with the LCD screen
facing out. This is convenient during playback
operations.
* DCR-SR38E/SR48E/SR57E/SR67E/
SR77E/SR87E
Power zoom lever (32, 40)
PHOTO button (24, 30)
CHG (charge) lamp (16)
ACCESS lamp (Hard disk) (16)
While the lamp is lit or flashing, the
7
Center
Indicator
Meaning
[STBY]/[REC]
Recording status (23, 29)
Photo size (68)
Slide show set (41)
Warning (89)
POWER button (19)
DISP (display) button (34)
EASY button (23)
(DISC BURN) button (see Operating
Guide)
Playback mode (26, 36)
Upper right
Indicator
Meaning
(VIEW IMAGES) button (25, 35)
Access lamp (“Memory Stick PRO Duo”
While the lamp is lit or flashing, the
camcorder is reading or writing data.
Recording mode (HQ/SP/
Recording/playback/
editing media (59)
Counter (hour:minute:
second) (22, 28, 35)
0:00:00
RESET button
Press RESET to initialize all the settings
Estimated recording
remaining time (22, 28)
[00min]
including the clock setting.
FADER (83)
Drop sensor off (77)
Drop sensor activated (77)
DCR-SR37E/SR38E/SR57E/SR77E: Output only
Approximate number of
recordable photos and
recording media (24, 30)
9999
9999
Screen indicators
Upper left
Center
Upper right
Playback folder (37)
Current playing movie or
photo/Number of total
recorded movies or photos
100/112
Bottom
Indicator
Meaning
Bottom
Face Index (38)
Manual focus (80)
Upper left
Indicator
Meaning
SCENE SELECTION (81)
HOME button (10)
Self-timer recording (84)
BLT-IN ZOOM MIC (83)
MICREF LEVEL low (84)
WIDE SELECT (65)
Remaining battery
White balance (82)
SteadyShot off (66)
METER (78)
60 min
TELE MACRO (79)
Return button (10)
8
Indicator
Meaning
Back light (33)
OPTION button (10)
VIEW IMAGES button
Slide show button (41)
Data file name (26, 36)
Protected image (49)
101-0001
101-0005
VISUAL INDEX button
* DCR-SR57E/SR67E/SR77E/SR87E
Indicators and their positions are approximate
and may differ from what you actually see.
Some items may not appear, depending on your
camcorder model.
9
Using the HELP function
“
“
HOME”and
To see the descriptions on the HOME
MENU, touch (HELP) on the HOME
MENU screen. (The bottom of turns
orange.) Then, touch the item you want to
know about.
OPTION”- Taking
advantage of two
types of menus
Using the OPTION MENU
Using the HOME MENU
The OPTION MENU appears just like
the pop-up window that appears when you
right-click the mouse on a computer. The
menu items you can change in the context
appear.
When you press (HOME), the HOME
MENU appears. You can change the
settings of your camcorder, etc.
(HOME)
(OPTION)
(HOME) button
Touch the desired category
the menu item to be changed.
Menu item
Touch the desired tab the
item to change the setting.
Menu item
Category
Tab
Follow the instructions on the
screen.
After completing the setting,
touch
.
After completing the setting,
touch
.
When the item is not on the screen, touch
Notes
/
.
When the item you want is not on the screen,
touch another tab. (There may be no tab.)
You cannot use the OPTION MENU during
Easy Handycam operation.
The tabs and items that appear on the screen
depend on the recording/playback status of
your camcorder at the time.
To return to the previous screen, touch
.
To hide the HOME MENU screen, touch
.
You cannot select the grayed items or
settings.
10
(MANAGE MEDIA) category
MOVIE MEDIA SET*1
PHOTO MEDIA SET*1
MEDIA INFO
Menu lists
p. 59
p. 59
p. 61
p. 62
p. 88
List of the HOME MENU
MEDIA FORMAT*1
REPAIR IMG.DB F.
(CAMERA) category
MOVIE*1
PHOTO*1
p. 28
p. 30
(SETTINGS) category
MOVIE SETTINGS
REC MODE
p. 64
p. 64
p. 65
p. 65
p. 66
p. 66
p. 66
p. 67
p. 67
(VIEW IMAGES) category
VISUAL INDEX*1
FILM ROLL*1
FACE*1
PLAYLIST
AUDIO MODE*2
WIDE SELECT
DIGITAL ZOOM
STEADYSHOT
AUTO SLW SHUTTR
GUIDEFRAME
REMAINING SET
FACE SET*1
p. 36
p. 38
p. 38
p. 52
(OTHERS) category
DELETE*1
DELETE
p. 44
p. 44
p. 46
DELETE
PHOTO SETTINGS
IMAGE SIZE*1
FILE NO.
PHOTO CAPTURE
MOVIE DUB
DUB by select
DUB by date
DUB ALL
p. 68
p. 68
p. 69
p. 69
p. 47
p. 47
p. 47
AUTO SLW SHUTTR
GUIDEFRAME
VIEW IMAGES SET
DATA CODE
PHOTO COPY
COPY by select
COPY by date
EDIT
p. 70
p. 48
p. 48
SOUND/DISP SET
VOLUME*1
p. 26, 36
p. 72
BEEP*1
DELETE
p. 44
p. 44
p. 49
p. 49
p. 50
LCD BRIGHT
p. 72
DELETE
LCD BL LEVEL
LCD COLOR
p. 72
PROTECT
p. 73
PROTECT
OUTPUT SETTINGS
TV TYPE
DIVIDE
p. 74
p. 74
PLAYLIST EDIT
ADD
DISP OUTPUT
CLOCK/ LANG
CLOCK SET*1
p. 51
p. 51
p. 52
p. 52
p. 52
ADD by date
ERASE
p. 19
p. 75
p. 75
p. 75
AREA SET
ERASE ALL
MOVE
SUMMERTIME
LANGUAGE SET*1
GENERAL SET
DEMO MODE
CALIBRATION
A.SHUT OFF
USB CONNECT
USB CONNECT
USB CONNECT
p. 55
p. 55
p. 76
p. 102
p. 76
DISC BURN
Operating Guide
p. 58
BATTERY INFO
POWER ON BY LCD
DROP SENSOR
p. 77
p. 77
11
[SOUND/DISP SET] is changed to [SOUND
SETTINGS] during Easy Handycam operation.
1
*
You can set this item during Easy Handycam
operation.
DCR-SR57E/SR67E/SR77E/SR87E
2
*
List of the OPTION MENU
Following items are available on the
OPTION MENU only.
tab
SPOT MTR/FCS
SPOT METER
SPOT FOCUS
TELE MACRO
EXPOSURE
FOCUS
p. 78
p. 78
p. 79
p. 79
p. 80
p. 80
p. 81
p. 82
SCENE SELECTION
WHITE BAL.
tab
FADER
p. 83
tab
BLT-IN ZOOM MIC
MICREF LEVEL
SELF-TIMER
p. 83
p. 84
p. 84
The tab depends on the situation/no tab
SLIDE SHOW
p. 41
SLIDE SHOW SET
p. 41
1ꢀ
Battery.pack
Read this before
operating your
camcorder
Supplied items
The camcorder is not dustproofed, dripproofed
Do not do any of the following when the
flashing. Otherwise, the recording media may
be damaged, recorded images may be lost or
other malfunctions could occur.
Ejecting the “Memory Stick PRO Duo” media
from the camcorder
Removing the battery pack or AC Adaptor
from the camcorder
The numbers in ( ) are the supplied
quantity.
AC Adaptor (1)
Power cord (Mains lead) (1)
A/V connecting cable (1)
USB cable (1)
Rechargeable battery pack
Only for DCR-SR37E/SR38E/SR47E/
SR48E/SR57E/SR67E: NP-FH30 (1)
Only for DCR-SR77E/SR87E: NP-FH50
(1)
CD-ROM “Handycam Application
Applying mechanical shock or vibration to
the camcorder
Software” (1)
“PMB (Picture Motion Browser)” including
“PMB Guide”
“Handycam Handbook” (PDF)
“Operating Guide” (1)
When connecting your camcorder to another
device with a cable, be sure to insert the
connector plug in the correct way. Pushing the
plug forcibly into the terminal will damage the
terminal and may result in a malfunction of
your camcorder.
Disconnect the AC Adaptor from the
camcorder, holding both the camcorder and the
DC plug.
can use with this camcorder.
Menu items, LCD panel, and lens
Using the camcorder
A menu item that is grayed out is not available
under the current recording or playback
conditions.
Do not hold the camcorder by the following
parts, and also do not hold the camcorder by
the jack covers.
The LCD screen is manufactured using
extremely high-precision technology, so over
99.99% of the pixels are operational for effective
use. However, there may be some tiny black
points and/or bright points (white, red, blue,
or green in color) that appear constantly on the
LCD screen. These points are normal results of
the manufacturing process and do not affect the
recording in any way.
LCD.screen
1ꢁ
Do not apply shock or vibration to your
camcorder
The hard disk of the camcorder may not be
recognized, or recording or playback may not
be possible.
Especially, during recording/playback, do not
apply shock. After recording, do not apply
vibration or shock to the camcorder, while the
ACCESS lamp is lit.
When using a shoulder belt (sold separately), do
not crash the camcorder against an object.
Do not use your camcorder in very loud areas.
Black points
White, red, blue or green points
Exposing the LCD screen, or the lens to direct
sunlight for long periods of time may cause
malfunctions.
Do not aim at the sun. Doing so might cause
your camcorder to malfunction. Take images
of the sun only in low light conditions, such as
at dusk.
On the drop sensor
To protect the internal hard disk from shock
by dropping, the camcorder has a drop sensor
under a non-gravity condition, the block noise
made when this function is activated by the
camcorder may also be recorded. If the drop
sensor catches a drop repeatedly, recording/
playback may be stopped.
About changing the language setting
The on-screen displays in each local language
are used for illustrating the operating
procedures. Change the screen language before
using your camcorder if necessary (p. 75).
Recording
Notes on battery pack/AC Adaptor
Be sure to remove the battery pack or the AC
Adaptor after turning off the camcorder.
Before starting to record, test the recording
function to make sure that the image and sound
are recorded without any problems.
Compensation for the contents of recordings
cannot be provided, even if recording or
playback is not possible due to a malfunction of
the camcorder, storage media, etc.
TV color systems differ depending on the
country/region. To view your recordings on a
TV, you need a PAL system-based TV.
Television programs, films, video tapes,
and other materials may be copyrighted.
Unauthorized recording of such materials may
be contrary to the copyright laws.
Note on operating temperatures
When the temperature of the camcorder
becomes extremely high or extremely low, you
may not be able to record or play back on the
camcorder, due to the protection features of the
camcorder being activated in such situations.
In this case, an indicator appears on the LCD
screen (p. 89).
When the camcorder is connected to a
computer
Do not try to format the hard disk or music file
storage area of the camcorder using a computer.
If you do so, your camcorder may not operate
correctly.
Notes on using the Hard Disk Drive
Handycam
Save all your recorded image data
Note on using the camcorder at high
altitudes
Do not turn on the camcorder in a low-pressure
area, where the altitude is more than 5,000
meters (16,000 feet). Doing so may damage the
hard disk drive of your camcorder.
To prevent your image data from being lost,
save all your recorded images on external media
periodically. It is recommended that you save
the image data on a disc such as a DVD-R using
your computer (see Operating Guide). Also, you
can save your image data using a DVD writer, a
VCR, or a DVD/HDD recorder (p. 53).
1ꢂ
Note on disposal/transfer
Even if you perform [ DELETE ALL],
[
DELETE ALL] or [MEDIA FORMAT],
some data might not be entirely deleted
from the hard disk. When you transfer the
camcorder, it is recommended that you perform
[
of your data. Also, when you dispose of the
camcorder, it is recommended that you destroy
the actual body of the camcorder.
If you cannot record/play back images,
perform [MEDIA FORMAT]
If you repeat recording/deleting images for
a long time, fragmentation of data occurs on
the recording media. Images cannot be saved
or recorded. In such a case, save your images
on some type of external media first (p. 53,
see Operating Guide too), and then perform
[MEDIA FORMAT] (p. 62).
Carl Zeiss lens
Your camcorder is equipped with a Carl Zeiss
lens, which was developed jointly by Carl Zeiss,
in Germany, and Sony Corporation, and produces
superior images. It adopts the MTF measurement
system for video cameras and offers a quality
typical of a Carl Zeiss lens.
MTF= Modulation Transfer Function. The
number value indicates the amount of light from a
subject coming into the lens.
1ꢃ
Getting started
Step 1: Charging the battery pack
CHG (charge) lamp
ACCESS lamp (Hard disk)
Battery pack
DC plug
DC IN jack
AC Adaptor
Power cord (Mains lead)
To the wall outlet (wall socket)
You can charge the “InfoLITHIUM” battery pack (H series) after attaching it to your
camcorder.
You cannot attach any “InfoLITHIUM” battery pack other than the H series to your camcorder.
Turn off your camcorder by closing the LCD screen.
1
Attach the battery pack by sliding it in the direction of the arrow until it
clicks.
2
Connect the AC Adaptor and the power cord (mains lead) to your
camcorder and the wall outlet (wall socket).
Be sure that the mark on the DC plug is facing down.
The CHG (charge) lamp lights up and charging starts. The CHG (charge) lamp turns off
when the battery pack is fully charged.
3
When the battery is charged, disconnect the AC Adaptor from the DC IN
jack of your camcorder.
4
When your camcorder is on, you can check the approximate amount of remaining battery power with the
remaining battery indicator at the upper left on the LCD screen.
1ꢄ
Charging time
Approximate time (min.) required when you fully charge a fully discharged battery pack.
DCR-SR37E/SR38E/SR47E/SR48E/SR57E/SR67E
Battery pack
NP-FH30 (supplied)
NP-FH50
NP-FH70
NP-FH100
Charging time
115
135
170
390
DCR-SR77E/SR87E
Battery pack
NP-FH50 (supplied)
NP-FH70
Charging time
135
170
390
NP-FH100
When the battery pack is charged at 25 C (77 ˚F) (10 C to 30 C (50 ˚F to 86 ˚F) is recommended)
To remove the battery pack
Close the LCD screen. Slide the BATT (battery) release lever and remove the battery pack
.
To use a wall outlet (wall socket) as a power source
attached, the battery pack is not discharged.
Charging the battery pack abroad
You can charge the battery pack in any countries/regions using the AC Adaptor supplied with
your camcorder within the AC 100 V - 240 V, 50 Hz/60 Hz range.
Do not use an electronic voltage transformer.
Notes on the battery pack
When you remove the battery pack or disconnect the AC Adaptor, close the LCD screen and make sure
that the
off.
The CHG (charge) lamp flashes during charging under the following conditions:
The battery pack is not attached correctly.
The battery pack is damaged.
In the default setting, the power turns off automatically if you leave your camcorder without any
operation for about 5 minutes, to save battery power ([A.SHUT OFF]).
17
Notes on the AC Adaptor
Use the nearby wall outlet (wall socket) when using the AC Adaptor. Disconnect the AC Adaptor from
the wall outlet (wall socket) immediately if any malfunction occurs while using your camcorder.
Do not use the AC Adaptor placed in a narrow space, such as between a wall and furniture.
Do not short-circuit the DC plug of the AC Adaptor or battery terminal with any metallic objects. This
may cause a malfunction.
18
Step 2: Turning the power on, and setting the
date and time
Open the LCD screen of your camcorder.
1
Your camcorder is turned on.
To turn on your camcorder when the LCD screen is open, press POWER.
POWER button
(Movie): To record movies
(Photo): To record photos
Select the desired geographical area with
/
, then touch [NEXT].
2
3
Touch the button on
the LCD screen.
To set the date and time again, touch
(HOME)
(SETTINGS) [CLOCK/ LANG]
[CLOCK SET]. When an item is not on the screen, touch
/
until the item appears.
Set [SUMMERTIME], date and time, then touch
.
The clock starts.
If you set [SUMMERTIME] to [ON], the clock advances 1 hour.
The date and time does not appear during recording, but they are automatically recorded on the
recording media, and can be displayed during playback. To display the date and time, touch (HOME)
(SETTINGS) [VIEW IMAGES SET] [DATA CODE] [DATE/TIME]
.
You can turn off the operation beeps by touching
SET] [BEEP] [OFF]
(HOME)
(SETTINGS) [SOUND/DISP
.
19
To turn off the power
Close the LCD screen. The (Movie) lamp flashes for a few seconds and the power is turned
off.
POWER button
You can turn off your camcorder also by pressing POWER.
Changing the language setting
You can change the on-screen displays to show messages in a specified language.
Touch (HOME)
a desired language
(SETTINGS) [CLOCK/ LANG] [ LANGUAGE SET]
.
ꢀ0
Recording/Playback
Five pieces of advice for successful recording
.Stabilizing.your.camcorder
When you hold the camcorder, keep your upper body upright,
and hold your arms close to your body.
The SteadyShot function is effective against camera-shake,
however, it is essential that you not move the camcorder.
.Zooming.smoothly
Zoom in and out slowly and smoothly. And, use zooming
sparingly. Excessive zooming will make movies that may make
the viewer feel tired when viewing them.
.Evoking.a.feeling.of.spaciousness
Use the panning technique. Stabilize yourself, move your
camcorder horizontally as you turn your upper body slowly. Stay
still at the end of panning for a while to make the scene look
stable.
.Accentuating.movies.with.narration
Consider the sound to be recorded with your movies. Narrate
the subject, or talk to the subject during shooting.
Aim for a balanced volume of voices, since the recording person
is closer to the microphone than the recorded person.
.Using.accessories
Make good use of camcorder accessories.
For example, using a tripod, you can make a time-lapse
recording or record subjects in dim light, such as scenes of
fireworks, or night views. By always carrying spare batteries, you
can continue recording without worrying about battery power
shortages.
ꢀ1
Recording and playing movies and photos easily
Easy Handycam Operation)
(
Simply press EASY. You can record or play movies and photos easily (Easy Handycam
operation).
During Easy Handycam operation, you can set basic options, such as changing the image size
or deleting images, among the setting and adjustment items. Other items are set automatically.
When Easy Handycam operation is started, nearly all menu settings are reset to the default settings
automatically. (Some menu items retain the settings that were made before Easy Handycam operation.)
Recording movies
In the default setting, movies are recorded on the
hard disk (p. 59).
Fasten the grip belt.
Open the lens cover.
Open the LCD screen of your camcorder.
Your camcorder is turned on.
ꢀꢀ
Open the LCD screen of your camcorder.
Your camcorder is turned on.
Press EASY.
appears on the LCD screen.
Press MODE to turn on the (Photo) lamp.
Press PHOTO lightly to adjust the focus, then press it fully.
Flashes Lights up
When
disappears, the photo is recorded on the internal hard disk.
ꢀꢂ
Playing movies
Open the LCD screen of your camcorder.
Your camcorder is turned on.
Press (VIEW IMAGES).
The VISUAL INDEX screen appears after some seconds.
Touch the (Movie) tab () a desired movie ().
Searches for images by
date (p. 39)
HOME MENU
Previous 6 images
Next 6 images
Returns to the
recording screen
: Displays the Film Roll Index screen (p. 38).
: Displays the Face Index screen (p. 38).
: Displays movies.
: Displays photos.
appears with the movie or photo that was most recently played or recorded. If you touch the
movie or photo with , you can continue playback from the previous time. ( appears on the
photo recorded on “Memory Stick PRO Duo” media.)
ꢀꢃ
Your camcorder starts playing the selected movie.
Volume adjustment
Previous
Next
To stop
To fast-forward
To pause/play
To fast-reverse
Tips
When playback from the selected movie reaches the last movie, the screen returns to the VISUAL INDEX
screen.
You can slow down the playback speed by touching
You can adjust the volume by touching adjust with
/
during pause.
/
during playback.
Viewing photos
On the VISUAL INDEX screen, touch the (Photo) tab () a desired photo
().
Your camcorder starts playing the selected photo.
Previous
Slide show/pause
Next
To the VISUAL
INDEX screen
ꢀꢄ
Tips
To cancel Easy Handycam operation
After you finish recording, or close menu setting screen, press EASY again.
from the LCD screen.
disappears
Menu settings during Easy Handycam operation
Notes
You cannot use the
OPTION MENU.
Cancel Easy Handycam operation if you want to add effects to images or change settings.
Invalid buttons during Easy Handycam operation
You cannot use some buttons/functions during Easy Handycam operation since they are
automatically set. If you set an invalid operation, [Invalid during Easy Handycam operation.]
may appear.
ꢀ7
Recording
Recording movies
In the default setting, movies are recorded on the
internal hard disk (p. 59).
Fasten the grip belt.
Open the lens cover.
Open the LCD screen of your camcorder.
Your camcorder is turned on.
ꢀ8
Press START/STOP to start recording.
[STBY] [REC]
To stop recording, press START/STOP again.
The maximum continuous recordable time of movies is about 13 hours.
When a movie file exceeds 2 GB, the next movie file is created automatically.
[ STEADYSHOT] is set to [ON] in the default setting.
It will take several seconds until you can start recording after you turn on the camcorder. You cannot
operate your camcorder during this time.
If you close the LCD screen while recording movies, the camcorder stops recording.
If the ACCESS/access lamp is lit or flashing after recording is finished, it means that data is still being
written onto the recording media. Do not apply shock or vibration to your camcorder, and do not remove
the battery or AC Adaptor.
You can check the recordable time and the remaining capacity, etc., by touching
(HOME)
To adjust the angle of the LCD panel, first open the LCD panel 90 degrees to the camcorder , and then
adjust the angle . If you rotate the LCD panel 180 degrees to the lens side , you can record movies/
photos in mirror mode.
90 degrees (max.)
90 degrees to the camcorder
180 degrees (max.)
When you open or close the LCD screen, or adjust the angle, be careful not to press the buttons on the
side of the LCD screen by mistake (DCR-SR38E/SR48E/SR57E/SR67E/SR77E/SR87E).
Tips
When a face is detected during movie recording, flashes and the detected face is stored in the index.
You can switch the shooting mode by touching
(HOME)
(CAMERA) [MOVIE].
ꢀ9
Data code during recording
The recording date, time and condition are recorded automatically on the recording media.
They are not displayed during recording. However, you can check them as [DATA CODE]
during playback (p. 70).
Shooting photos
In the default setting, photos are recorded on the internal hard disk (p. 59).
Open the lens cover.
Open the LCD screen of your camcorder.
Your camcorder is turned on.
Press MODE to turn on the (Photo) lamp.
ꢁ0
Press PHOTO lightly to adjust the focus, then press it fully.
Flashes Lights up
disappears, the photo is recorded.
When
To change the image size, touch
(HOME)
(SETTINGS) [PHOTO SETTINGS]
(p. 68).
[
IMAGE SIZE] a desired setting
You cannot record photos while
is displayed.
ꢁ1
Useful functions for recording movies and photos
Zooming
You can magnify images with the power zoom lever.
You can also magnify images with the zoom buttons on the LCD frame (DCR-SR38E/SR48E/
SR57E/SR67E/SR77E/SR87E).
The magnifying level of your camcorder is as follows:
DCR-SR37E/SR38E/SR47E/SR48E/SR57E/SR67E: 60 times the original size
DCR-SR77E/SR87E: 25 times the original size
Wider range of view
(Wide angle)
Close view
(Telephoto)
Move the power zoom lever slightly for a slower zoom. Move it further for a faster zoom.
Notes
SteadyShot may not reduce image blurring as desired when the power zoom lever is set to the T
(Telephoto) side.
Be sure to keep your finger on the power zoom lever. If you move your finger off the power zoom lever,
the operation sound of the power zoom lever may also be recorded.
You cannot change the zoom speed with the zoom buttons on the LCD frame
(DCR-SR38E/SR48E/SR57E/SR67E/SR77E/SR87E).
The minimum possible distance between camcorder and subject while maintaining sharp focus
is about 1 cm (about 13/32 in.) for wide angle and about 150 cm (about 59 1/8 in.) for telephoto
(DCR-SR37E/SR38E/SR47E/SR48E/SR57E/SR67E).
The minimum possible distance between camcorder and subject while maintaining sharp focus
is about 1 cm (about 13/32 in.) for wide angle and about 80 cm (about 31 1/2 in.) for telephoto
(DCR-SR77E/SR87E).
Tips
ꢁꢀ
Recording sound with more presence (5.1ch surround recording) (DCR-
SR57E/SR67E/SR77E/SR87E)
Dolby Digital 5.1ch surround sound can be recorded with the built-in microphone. You can
enjoy realistic sound when playing the movie on devices that support 5.1ch surround sound.
Built-in microphone
Notes
If you play back 5.1ch sound on your camcorder, 5.1ch sound is automatically converted and output in
2ch.
Tips
You can select the recording sound from [5.1ch SURROUND] (
([AUDIO MODE], p. 64).
) or [2ch STEREO] (
)
You can create a disc, which contains the movies recorded on your camcorder, on a computer using the
supplied software. If you play the disc on a 5.1ch surround system, you can enjoy realistic sound.
Adjusting the exposure for backlit subjects
To adjust the exposure for backlit subjects, press (back light) to display . To cancel the
back light function, press (back light) again.
ꢁꢁ
Recording in mirror mode
Open the LCD panel 90 degrees to the camcorder , then rotate it 180 degrees to the lens
side .
Tips
A mirror-image of the subject appears on the LCD screen, but the image will be normal when recorded.
Switching the screen display
Information (remaining battery capacity, etc.) toggles off and on each time you press DISP.
ꢁꢂ
Playback.on.the.camcorder
In the default setting, movies and photos that are recorded on the internal hard disk are
played (p. 59).
Playing movies
Open the LCD screen of your camcorder.
Your camcorder is turned on.
Press (VIEW IMAGES).
The VISUAL INDEX screen appears after some seconds.
You can display the VISUAL INDEX screen by pressing
as well.
(VIEW IMAGES) on the LCD screen
Touch the (Movie) tab () a desired movie ().
To the list of recording
dates (p. 39)
Previous
Next
To return to
recording mode
: Displays the Film Roll Index screen (p. 38).
: Displays the Face Index screen (p. 38).
: Displays movies.
: Displays photos.
appears with the movie or photo that was most recently played or recorded. If you touch the
movie or photo with , you can continue playback from the previous time. ( appears on the
photo recorded on “Memory Stick PRO Duo” media.)
ꢁꢃ
Your camcorder starts playing the selected movie.
Previous
Next
Volume adjustment
OPTION
To stop
To fast-forward
To fast-reverse
To pause/play
Tips
When playback from the selected movie reaches the last movie, the screen returns to the VISUAL INDEX
screen.
Touch
As you repeat touching
/
during pause to play back movies slowly.
during playback, movies are played as fast as about 5 times about
/
10 times about 30 times about 60 times.
You can display the VISUAL INDEX by touching
INDEX].
(HOME)
(VIEW IMAGES) [VISUAL
The recording date, time, and shooting conditions are recorded automatically during recording. This
information is not displayed during recording, but you can display it during playback by touching
(HOME)
(SETTINGS) [VIEW IMAGES SET] [DATA CODE] a desired setting
.
To adjust the sound volume of movies
While playing back movies, touch
adjust with
/
.
You can adjust the sound volume from the OPTION MENU.
Viewing photos
Touch the (Photo) tab () a desired photo () on the VISUAL INDEX
screen.
ꢁꢄ
Useful functions for playing movies and photos
Searching for desired scene by pinpoint (Film Roll Index)
Movies can be divided by a set time and the first scene of each division is displayed on the
INDEX screen. You can start playing back a movie from the selected thumbnail.
Select the recording media which contains the movie you want to play back before the
operation (p. 59).
Press
(VIEW IMAGES).
The VISUAL INDEX screen appears.
Touch (Film Roll Index).
Returns to the VISUAL INDEX screen
Sets the interval at which to create thumbnails of scenes in a movie.
Touch
Touch
/
/
to select the desired movie.
to search for the desired scene, then touch the scene you want
to play back.
Playback starts from the selected scene.
Tips
You can also display the [Film Roll Index] screen by touching
(HOME)
(VIEW IMAGES)
[
FILM ROLL].
Searching for desired scene by face (Face Index)
The face images detected during movie recording are displayed on the INDEX screen.
You can play back the movie from the selected face image.
Select the recording media which contains the movie you want to play back before the
operation (p. 59).
ꢁ8
Press
(VIEW IMAGES).
The VISUAL INDEX screen appears.
Touch (Face Index).
Returns to the VISUAL INDEX screen
Touch
Touch
/
/
to select the desired movie.
to search for the desired face image, then touch the desired
face image to view the scene.
Playback starts from the beginning of the scene with the selected face image.
Notes
Faces may not be detected depending on recording conditions.
Example: People wearing glasses or hats, or who do not face towards the camera.
Tips
You can also display the [Face Index] screen by touching
FACE].
(HOME)
(VIEW IMAGES)
[
Searching for desired images by date (Date Index)
You can search for desired images by date efficiently.
Select the recording media which contains the image you want to play back before the
operation (p. 59).
Notes
You cannot use the Date Index function for photos on the “Memory Stick PRO Duo” media.
Press
(VIEW IMAGES).
The VISUAL INDEX screen appears.
ꢁ9
To search for movies, touch the (Movie) tab. To search for photos, touch
the (Photo) tab.
Touch date on the screen.
The recording dates of images are displayed on the screen.
Returns to the VISUAL INDEX screen
Touch
/
to select the date of the desired image, then touch
.
The images of the selected date are displayed on the VISUAL INDEX screen.
Tips
On the [Film Roll Index]/[Face Index] screen, you can use the Date Index function by following the steps
3 to 4.
Using PB zoom with photos
You can magnify photos from about 1.1 to 5 times the original size.
Magnification can be adjusted with the power zoom lever.
For DCR-SR38E/SR48E/SR57E/SR67E/SR77E/SR87E:
You can also magnify images with the zoom buttons on the LCD frame.
Play back the photo you want to magnify.
Magnify the photo with T (Telephoto).
The screen is framed.
ꢂ0
Touch the screen at the point you want to display in the center of the
displayed frame.
Adjust the magnification with W (Wide angle)/T (Telephoto).
To cancel, touch
.
Playing back a series of photos (Slide show)
Touch
on the photo playback screen.
The slide show begins from the selected photo.
To stop the slide show
Touch
.
To restart the slide show
Touch
again.
Notes
You cannot operate playback zoom during slide show.
Tips
You can also play back the slide show by touching
VISUAL INDEX screen.
You can set continuous slide show playback by selecting
(OPTION)
tab [SLIDE SHOW] on the
tab [SLIDE SHOW
(OPTION)
SET] while playing photos. The default setting is [ON] (continuous playback).
ꢂ1
Playing images on a TV
Connect your camcorder to the input jack of a TV or VCR using the A/V connecting cable
or an A/V connecting cable with S VIDEO . Connect your camcorder to the wall
instruction manuals supplied with the devices to be connected.
A/V connecting cable (supplied)
Connecting to another device via the A/V jack using an A/V connecting cable.
A/V connecting cable with S VIDEO (sold separately)
When connecting to another device via the S VIDEO jack, by using an A/V connecting cable
with an S VIDEO cable (sold separately), higher quality images can be produced than with an
A/V connecting cable. Connect the white and red plugs (left/right audio) and the S VIDEO plug
(S VIDEO channel) of the A/V connecting cable with an S VIDEO cable (sold separately). The
yellow plug connection is not necessary. Connecting only the S VIDEO plug will not output
audio.
IN
VIDEO
AUDIO
TVs
(Yellow)
(White)
(Red)
S VIDEO
VCRs
(Yellow)
:Signal flow
A/V Remote Connector
Set the input selector of the TV to the input your camcorder will be
connected to.
For details, refer to the instruction manuals supplied with the TV.
Connect your camcorder to a TV with the A/V connecting cable (,
supplied) or an A/V connecting cable with S VIDEO (, sold separately).
Connect your camcorder to the input jack of the TV.
ꢂꢀ
Play back movies and photos on your camcorder (p. 35).
To set the aspect ratio according to the connected TV (16:9/4:3)
Touch (HOME)
[4:3]
(SETTINGS) [OUTPUT SETTINGS] [TV TYPE] [16:9] or
.
Tips
To check information (counter, etc.) on the screen of the monitor, touch
(HOME)
(SETTINGS)
[OUTPUT SETTINGS] [DISP OUTPUT] [V-OUT/PANEL] (default setting)
.
When connecting to your TV via a VCR
Connect your camcorder to the LINE IN input on the VCR using the A/V connecting cable.
Set the input selector on the VCR to LINE (VIDEO 1, VIDEO 2, etc.).
When your TV is monaural (When your TV has only one audio input jack)
Connect the yellow plug of the A/V connecting cable to the video input jack and connect the
white (left channel) or red (right channel) plug to the audio input jack of your TV or VCR.
If your TV/VCR has a 21-pin adaptor (EUROCONNECTOR)
Use a 21-pin adaptor (sold separately) to view playback pictures.
TV/VCR
Notes
When you set [TV TYPE] to [4:3], the image quality may deteriorate. Also, when the recorded image’s
aspect ratio switches between 16:9 (wide) and 4:3, the image may jitter.
On some 4:3 TVs, the still images recorded in 4:3 aspect ratio may not be displayed full screen. This is
not a malfunction.
When you play back an image recorded in 16:9 (wide) aspect ratio on a 4:3 TV not compatible with the
16:9 (wide) signal, set [TV TYPE] to [4:3].
ꢂꢁ
Editing
Deleting movies and
photos
You can free media space by deleting
movies and photos from recording media.
Select the recording medium that contains
the movies and photos you want to delete
before starting the operation (p. 59).
3
4
Touch and display the mark
on the movies or photos to be
deleted.
Notes
You cannot restore images once they are
deleted.
Tips
Press and hold the image down on the
LCD screen to confirm the image. Touch
to return to the previous screen.
Do not remove the battery pack or the AC
Adaptor from your camcorder while deleting
the images. It may damage the recording media.
Do not eject “Memory Stick PRO Duo” media
while deleting images from the “Memory Stick
PRO Duo” media.
You cannot delete protected movies and photos.
Undo the protection of the movies and photos
to delete them, before you try to delete them
(p. 49).
If the deleted movie is included in the Playlist
deleted also from the Playlist.
Save important movies and photos in advance
(p. 53).
Touch
.
[YES]
To delete all movies/photos at one time
In step 2, touch [ DELETE]
[
DELETE ALL] [YES] [YES]
.
To delete all photos at one time, touch
DELETE] [ DELETE ALL] [YES]
[YES]
[
.
Tips
You can select up to 100 images at one time.
You can delete an image on the playback screen
To delete all the movies/photos
recorded on the same day at one time
You can delete photos by selecting recording
dates only when photos are recorded on the
internal hard disk.
from
OPTION MENU.
To delete all images recorded in the recording
media, and recover all the recordable space of
the media, format the media (p. 62).
Reduced-size images which enable you to view
many images at the same time on an index
screen are called “thumbnails.”
In step 2, touch [ DELETE]
[
DELETE by date].
To delete all photos on the same day at one
time, touch [ DELETE] [ DELETE
by date].
1
2
Touch (HOME)
[DELETE].
(OTHERS)
To delete movies, touch
[
DELETE] [ DELETE].
To delete photos, touch [ DELETE]
DELETE].
Touch
/
to select the recording date
[
ꢂꢂ
of the desired movies/photos, then touch
.
The movies/photos recorded on the
selected date are displayed on the
screen.
Tips
Touch the image down on the LCD screen
to confirm the image. Touch
to the previous screen.
to return
Touch
[YES]
.
ꢂꢃ
To continue capturing, touch
repeat steps from step 3.
To capture a photo from another movie,
, then
Capturing a photo
from a movie
touch
, then repeat steps from step 2.
You can save a selected frame from a
recorded movie as a photo.
Select the recording media which contains
movies, and the recording media where you
want to save photos before the operation
(p. 59).
5
Touch
.
Notes
The image size is fixed depending on the aspect
ratio of the movie:
[
0.2M] in the aspect ratio 16:9
1
Touch (HOME)
[PHOTO CAPTURE].
The [PHOTO CAPTURE] screen
appears.
(OTHERS)
[VGA(0.3M)] in the aspect ratio 4:3
The recording medium where you want to save
photos should have enough free space.
The recording date and time of captured photos
is the same as the recording date and time of
the movies.
If the movie you are capturing from has no data
code, the recording date and time of the photo
will be the date and time you captured from
the movie.
2
3
Touch the movie to be captured.
The selected movie starts playback.
You cannot capture a photo from a movie
recorded on “Memory Stick PRO Duo” media
(DCR-SR37E/SR38E/SR57E/SR77E).
Touch
at the point where
you want to capture.
The movie pauses. Play and pause
toggles as you press
.
Adjust the capturing point with
more precision after you selected
the point with
.
Returns to the beginning of the selected
movie
4
Touch
.
The captured photo is saved on the
recording media selected in [PHOTO
MEDIA SET] (p. 59).
When capturing is finished, the screen
returns to pause.
ꢂꢄ
Dubbing/copying
movies and photos
from the internal hard
disk to “Memory Stick
PRO Duo”media
Touch the type of dubbing.
[DUB by select]: To select movies and
dub
[DUB by date]: To dub all movies of a
specified date
[
DUB ALL]: To dub the Playlist
When you select the Playlist as the
source of dubbing, follow the on-screen
instructions to dub the Playlist.
Dubbing movies
You can dub movies recorded on the
internal hard disk of your camcorder to
“Memory Stick PRO Duo” media.
Insert “Memory Stick PRO Duo” media
into your camcorder before the operation.
Select the movie to be dubbed.
[DUB by select]: Touch the movie to be
dubbed, and mark it with . You can
select multiple movies.
Notes
When you record a movie on the “Memory
Stick PRO Duo” media for the first time, create
the image database file by touching
(MANAGE MEDIA) [REPAIR IMG.
DB F.] [MEMORY STICK].
(HOME)
Connect your camcorder to the wall outlet
(wall socket) using the supplied AC Adaptor to
prevent your camcorder from running out of
power during dubbing.
Remaining capacity of the
“Memory Stick PRO Duo” media
Tips
Tips
Press and hold the image down on the
LCD screen to confirm the image. Touch
to return to the previous screen.
The original movie will not be deleted after
dubbing.
All included images in a Playlist will be dubbed.
The images recorded by this camcorder and
stored onto the recording media are called
“original.”
[DUB by date]: Select the recording
date of the movie to be dubbed, then
touch
dates.
. You cannot select multiple
Touch (HOME)
[MOVIE DUB].
(OTHERS)
The [MOVIE DUB] screen appears.
Touch
.
[YES]
ꢂ7
Tips
Tips
To check the dubbed movies after dubbing is
finished, select [MEMORY STICK] on [MOVIE
MEDIA SET] and play them back (p. 59).
Press and hold the image down on the
screen to confirm the image. Touch
return to the previous screen.
to
[COPY by date]: Select the recording
date of the photo to be copied, then
Copying photos
touch
dates.
. You cannot select multiple
You can copy photos from the internal hard
disk of the camcorder to “Memory Stick
PRO Duo” media.
Insert “Memory Stick PRO Duo” media
into your camcorder before the operation.
Notes
Connect your camcorder to the wall outlet
(wall socket) using the supplied AC Adaptor to
prevent your camcorder from running out of
power during copying.
Touch
.
[YES]
Touch (HOME)
[PHOTO COPY].
(OTHERS)
Tips
The [PHOTO COPY] screen appears.
To check the copied photos after copying
is finished, select [MEMORY STICK] on
[PHOTO MEDIA SET] and play them back
(p. 59).
Touch the type of copying.
[COPY by select]: To copy selected
photos
[COPY by date]: To copy all photos of
a specified date
Select the photo to be copied.
[COPY by select]: Touch the photo to
be copied, and mark with . You can
select multiple photos.
ꢂ8
Protecting recorded
movies and photos
(Protect)
4
Touch
.
[YES]
Protect movies and photos to avoid deleting
them by mistake.
Select the recording medium that contains
the movies and photos you want to protect
before starting the operation (p. 59).
To undo the protection of movies and
photos
Touch the movie or photo marked with
in step 3.
disappears.
Tips
To protect all the movies and photos
recorded on the same day at one time
You can protect photos recorded on the internal
You can protect movies and photos on the
playback screen from
OPTION MENU.
hard disk by selecting their recording date.
1
2
Touch (HOME)
[EDIT].
(OTHERS)
In step 2, touch [ PROTECT]
[
PRT. by date].
To protect all photos on the same day at
one time, touch [ PROTECT]
To protect movies, touch
[
PRT. by date].
[
PROTECT] [ PROTECT].
To protect photos, touch [ PROTECT]
[ PROTECT].
3
Touch the movies and photos to
be protected.
is displayed on the selected images.
Touch
/
to select the recording date
of the desired movies/photos, then touch
.
Tips
Touch the image down on the LCD screen
to confirm the image. Touch
to the previous screen.
to return
Touch
[ON]
.
Tips
Press and hold the image down on the
LCD screen to confirm the image. Touch
to return to the previous screen.
You can select up to 100 images at one
time.
To undo the protection of movies and
photos recorded on the same day at
one time
In step above, select the recording date
of the desired movies/photos, then touch
[OFF]
.
ꢂ9
A slight difference may occur from the point
where you touch and the actual dividing
point, as your camcorder selects the dividing
point based on about half-second increments.
If you divide the original movie, the movie
added to the Playlist will also be divided.
Dividing a movie
Select the recording medium which
contains the movie you want to divide
before the operation (p. 59).
Tips
You can divide a movie on the playback screen
1
2
3
Touch (HOME)
[EDIT] [ DIVIDE].
(OTHERS)
from
OPTION MENU.
Touch the movie to be divided.
The selected movie starts playback.
Touch
at the point where
you want to divide the movie into
scenes.
The movie pauses. Play and pause
toggles as you press
.
Adjusts the dividing point with
more precision after you selected
the dividing point with
.
Returns to the beginning of the selected
movie
4
Touch
.
[YES]
Notes
You cannot restore movies once they are
divided.
Do not remove the battery pack or the AC
Adaptor from your camcorder while dividing
the movie. It may damage the recording media.
Also, do not eject the “Memory Stick PRO Duo”
media while dividing movies on the “Memory
Stick PRO Duo” media.
ꢃ0
To add all the movies recorded on the
same day at one time
In step 2, touch [ ADD by date].
The recording dates of movies are
displayed on the screen.
Using the Playlist of
movies
The Playlist is a list showing thumbnails of
the movies that you have selected.
The original movies are not changed even if
you edit or delete the movies added to the
Playlist.
Select the recording media you want to
create, play, or edit a Playlist before the
operation (p. 59).
Touch
/
to select the recording date
of the desired movie, then touch
The movies recorded on the selected
date are displayed on the screen.
.
Creating the Playlist
Touch (HOME)
(OTHERS)
[PLAYLIST EDIT].
Tips
Touch the image on the LCD screen to
confirm the image. Touch
the previous screen.
to return to
Touch [ ADD].
Touch
[YES]
.
Notes
Do not remove the battery pack or the AC
Adaptor from your camcorder while adding
movies to the Playlist. It may damage the
recording media. Also, do not eject the
Touch the movie to be added to
the Playlist.
“Memory Stick PRO Duo” media while editing
movies on the “Memory Stick PRO Duo” media.
You cannot add photos to the Playlist.
Tips
The selected movie is marked with
.
You can add a maximum of 99 movies to the
Playlist.
You can add a movie on the playback screen or
Tips
Press and hold the image down on the
LCD screen to confirm the image. Touch
to return to the previous screen.
the INDEX screen by touching
(OPTION).
You can copy the Playlist to a disc as it is, by
using the supplied software.
Touch
.
[YES]
ꢃ1
Tips
Playing the Playlist
Even if you erase a movie from a Playlist, the
original movie is not erased.
Select the recording media you want to play
a Playlist before the operation (p. 59).
To change the order within the Playlist
Touch (HOME) (OTHERS)
[PLAYLIST EDIT].
Touch [ MOVE].
Touch (HOME)
IMAGES) [PLAYLIST].
(VIEW
Select the movie to be moved.
Movies added to the Playlist appear.
The selected movie is marked with
.
Touch the movie you want to
play back.
Tips
Touch the image on the LCD screen to
confirm the image. Touch
the previous screen.
to return to
The Playlist is played back from the
selected movie to the end, then the
screen returns to the Playlist screen.
Touch
.
Select the destination with
/
.
To erase unnecessary movies from the
Playlist
Touch (HOME) (OTHERS)
[PLAYLIST EDIT].
Touch [ ERASE].
To erase all the movies from the Playlist,
touch [ ERASE ALL] [YES]
Destination bar
[YES]
Touch
.
[YES]
.
Tips
Select the movie to be erased from the
list.
When you select multiple movies, the movies
are moved following the order appearing in the
Playlist.
The selected movie is marked with
.
Tips
Press and hold the image down on the
LCD screen to confirm the image. Touch
to return to the previous screen.
Touch
[YES]
.
ꢃꢀ
Creating a disc with a
DVD writer, recorder
Insert an unused disc into the
DVD writer, and close the disc
tray.
The [DISC BURN] screen appears on
the camcorder screen.
Creating a disc with the dedicated
DVD writer, DVDirect Express
Operating on the camcorder screen, you
can save movies on a disc when using the
dedicated DVD writer, DVDirect Express
(sold separately). You can also play back
images on a created disc.
Refer also to the instruction manual
Press
writer.
(DISC BURN) on the DVD
supplied with the DVD writer.
DVDirect Express is referred to as “DVD
writer” in this section.
Only unused discs of the following types can
be used:
12cm DVD-R
12cm DVD+R
The device does not support two-layered discs.
Sony DVD writer may not be available in some
countries/regions.
Movies recorded on the internal hard
disk that have not been saved on any
discs will be recorded onto the disc.
After the disc has been created, the disc
tray on the DVD writer opens and you
can remove the disc.
You can also operate with
(DISC
BURN) on your camcorder.
Turn on your camcorder, and
connect the DVD writer to the
(USB) jack of your camcorder
with the USB cable of the DVD
writer.
Repeat steps 2 and 3 when the
total memory size of movies to
be burnt exceeds that of the disc.
After the operation is completed,
touch
[END] on the
camcorder screen.
Touch [EJECT DISC] and remove any
inserted disc.
The [EXTERNAL DRIVE] screen
appears on the camcorder screen.
Close the disc tray on the DVD
writer, and disconnect the USB
cable.
Notes
Use the supplied AC Adaptor as the power
DVD writer does not work.
ꢃꢁ
To create a disc with the selected
images
To dub a desired image onto the disc or to
create many of the same discs, perform this
operation.
Close the disc tray on the DVD writer,
and disconnect the USB cable from your
camcorder.
To play back a disc on the DVD writer
Touch [DISC BURN OPTION] in step 3
above.
Turn on your camcorder, and connect
the DVD writer to the (USB) jack of
your camcorder with the USB cable of
the DVD writer.
The [EXTERNAL DRIVE] screen
appears.
Select the recording media containing
the movie(s) you want to save.
Movie thumbnails appear on the
camcorder screen.
Touch the movie you want to burn on
the disc.
Tips
appears.
You can play back movies on the TV
screen by connecting the camcorder to a
TV (p. 42).
Insert a created disc into the DVD
writer.
The movies on the disc appear as
VISUAL INDEX on the camcorder
screen.
Press the play button on the DVD writer.
The movie plays back on the camcorder
Remaining Disc capacity
Tips
Press and hold the image down on the
LCD screen to confirm the image. Touch
to return to the previous screen.
By touching date, you can search for
images by date.
screen.
You can also operate by the camcorder
screen (p. 35).
Touch [END] [EJECT DISC] on the
camcorder screen and remove the disc
after the operation is completed.
Touch
screen.
[YES] on the camcorder
The disc tray on the DVD writer opens
after creating the disc.
Remove the disc from the DVD writer,
Press
and disconnect the USB cable.
Notes
Be sure to turn on the camcorder. The DVD
writer is powered from the camcorder.
You can use [DISC BURN OPTION] to create
many of the same disc.
and close the disc tray.
To create another disc of the same
contents, insert a new disc and touch
[CREATE SAME DISC].
After the operation is completed, touch
[EXIT] [END] on the camcorder
screen.
ꢃꢂ
Do not do any of the following when creating
a disc.
Sony DVD writer may not be available in some
countries/regions.
Turn off the camcorder
Disconnect the USB cable or the AC adaptor
Subject the camcorder to mechanical shock
or vibration
Eject the “Memory Stick PRO Duo” media
from the camcorder
You cannot add movies to a created disc.
Play the created disc to make sure dubbing was
performed correctly before deleting the movies
on your camcorder.
Turn on your camcorder, and
connect a DVD writer, etc., to the
(USB) jack of your camcorder
with the USB cable (supplied).
If [Failed.] or [DISC BURN failed.] appears on
the screen, insert another disc into the DVD
writer and touch
(DISC BURN) again.
Tips
The [USB SELECT] screen appears on
If the total memory size of movies to be burnt
by the DISC BURN operation exceeds that of
the disc, disc creation stops when the limit is
reached. The last movie on the disc may be
cut off.
the camcorder screen.
If the [USB SELECT] screen does
not appear, touch
(HOME)
(OTHERS) [USB CONNECT].
Disc creation time to dub movies to the limit of
the disc is about 20 to 60 minutes. It may take
more time depending on the recording mode or
the number of scenes.
You can play back created discs on a general
DVD player. If playback is not possible for any
reason, connect the camcorder to the DVD
writer, and then play back.
Touch [ USB CONNECT] when
movies are recorded on the
internal hard disk, or [ USB
CONNECT] when movies are
recorded on “Memory Stick PRO
Duo”media on the camcorder
screen.
The disc mark appears on the camcorder
screen.
Creating a disc with a DVD writer,
etc., other than DVDirect Express
Record movies on the connected
device.
For details, refer to the instruction
manuals supplied with the device to be
connected.
You can save movies on a disc by
connecting your camcorder to disc creation
devices, such as a Sony DVD writer other
than DVDirect Express, with the USB
cable. Refer also to the instruction manuals
supplied with the devices to be connected.
The method used to create a disc by
After the operation is completed,
touch [END] [YES] on the
camcorder screen.
connecting your camcorder to a Sony DVD
writer with the USB cable is described here.
Connect your camcorder to the wall outlet (wall
socket) using the supplied AC Adaptor for this
operation (p. 17).
Disconnect the USB cable.
ꢃꢃ
A/V Remote
Connector
Creating a disc with a recorder, etc.
You can dub images played back on your
camcorder to a disc or video cassette,
by connecting your camcorder to a disc
recorder, a Sony DVD writer other than
DVDirect Express, etc., with the A/V
connecting cable. Connect the device
in either way of or . Refer also to
the instruction manuals supplied with
the devices to be connected. Select the
recording medium that contains movies
you want to dub before starting the
Input
S VIDEO
operation (p. 59).
VIDEO
Sony DVD writer may not be available in some
countries/regions.
(Yellow)
(White)
Notes
Connect your camcorder to the wall outlet (wall
socket) using the supplied AC Adaptor for this
operation (p. 17).
AUDIO
(Red)
(Yellow)
A/V connecting cable (supplied)
Connect the A/V connecting cable to the
input jack of another device.
Signal flow
A/V connecting cable with S VIDEO
(sold separately)
When connecting to another device
via the S VIDEO jack, by using an A/V
connecting cable with an S VIDEO cable
(sold separately), higher quality images can
be produced than with an A/V connecting
cable. Connect the white and red plug
(left/right audio) and the S VIDEO plug
(S VIDEO channel) of the A/V connecting
cable with an S VIDEO cable. If you
connect the S VIDEO plug only, you will
hear no sound. The yellow plug (video)
connection is not necessary.
Insert the recording media in the
recording device.
If your recording device has an input
selector, set it to the input mode.
Connect your camcorder to the
recording device (a disc recorder,
etc.) with the A/V connecting
cable (supplied) or an A/V
connecting cable with S VIDEO
(sold separately).
Connect your camcorder to the input jacks
of the recording device.
ꢃꢄ
Start playback on your
camcorder, and record it on the
recording device.
Refer to the instruction manuals supplied
with your recording device for details.
When dubbing is finished, stop
the recording device, and then
your camcorder.
Notes
Since dubbing is performed via analog data
transfer, the image quality may deteriorate.
To hide the screen indicators (such as a
counter, etc.) on the screen of the monitor
device connected, touch
(HOME)
(SETTINGS) [OUTPUT SETTINGS]
[DISP OUTPUT] [LCD PANEL] (the
default setting)
To record the date/time or camera settings data,
touch (HOME) (SETTINGS)
[VIEW IMAGES SET] [DATA CODE] a
.
desired setting
. In addition, touch
(HOME)
(SETTINGS) [OUTPUT SETTINGS]
[DISP OUTPUT] [V-OUT/PANEL]
.
When the screen size of display devices
(TV, etc.) is 4:3, touch (HOME)
(SETTINGS) [OUTPUT SETTINGS]
[TV TYPE] [4:3] .
When you connect a monaural device, connect
the yellow plug of the A/V connecting cable
to the video input jack, and the white (left
channel) or the red (right channel) plug to the
audio input jack on the device.
ꢃ7
Utilizing recording media
Selecting the recording media for
photos
Changing the
recording media
Touch (HOME)
(MANAGE MEDIA) [PHOTO
MEDIA SET].
You can select the internal hard disk or
“Memory Stick PRO Duo” media as the
recording, playback, or editing medium on
your camcorder. Select the medium to be
used for movies and photos separately. In
the default setting, both movies and photos
are recorded on the internal hard disk.
The [PHOTO MEDIA SET] screen
appears.
Touch the desired recording
medium.
Hard disk
Movies
Photos
Touch [YES]
.
“Memory Stick” media
The recording medium is changed.
You can do recording, playback, and editing
operations on the selected medium.
photos.
To check the recording media settings
Light up the (Movie) lamp to check the
recording medium used for movies, or the
(Photo) lamp for photos. The media icon
is displayed at the top right corner of the
screen.
Selecting the recording media
Touch (HOME)
(MANAGE MEDIA) [MOVIE
MEDIA SET].
: Internal hard disk
: “Memory Stick PRO Duo” media
The [MOVIE MEDIA SET] screen
appears.
Inserting “Memory Stick PRO Duo”
media
Touch the desired medium.
Set the recording medium to [MEMORY
STICK] to record movies and/or photos on
“Memory Stick PRO Duo” media (p. 59).
Touch [YES]
.
The recording medium is changed.
Types of “Memory Stick”media you can
use with your camcorder
For recording movies, it is recommended that
you use “Memory Stick PRO Duo” media of 512
MB or larger marked with:
(“Memory Stick
PRO Duo” media)*
ꢃ9
(“Memory Stick
PRO-HG Duo” media)
* Marked with Mark2 or not, either can be
used.
Stick PRO Duo” media.
“Memory.Stick.PRO.Duo”.media/“Memory.Stick.PRO-HG.
Duo”.media..
(This.size.can.be.used.with.your.camcorder.)
Access lamp
(“Memory Stick PRO Duo” media)
“Memory.Stick”.media.
The [Create a new Image Database
File.] screen appears if you insert new
“Memory Stick PRO Duo” media when
the (Movie) lamp is lit.
(You.cannot.use.it.in.your.camcorder.)
You cannot use any type of memory card other
than those mentioned above.
“Memory Stick PRO Duo” media can be
used only with “Memory Stick PRO” media
compatible equipment.
Touch [YES].
To record only photos on “Memory Stick
PRO Duo” media, touch [NO].
Do not attach a label or the like on “Memory
Stick PRO Duo” media or “Memory Stick Duo”
media adaptor.
Insert the “Memory Stick PRO Duo” media into
the “Memory Stick Duo” media adaptor when
using “Memory Stick PRO Duo” media with
“Memory Stick” media compatible equipment.
Notes
If [Failed to create a new Image Database File.
It may be possible that there is not enough
free space.] is displayed in step 2, format the
“Memory Stick PRO Duo” media (p. 62).
To eject the “Memory Stick PRO Duo”
media
Open the “Memory Stick Duo” media cover
and lightly push the “Memory Stick PRO
Duo” media in once.
Do not open the “Memory Stick Duo” media
cover during recording.
Open the “Memory Stick Duo”
media cover, and insert the
“Memory Stick PRO Duo”media
into the “Memory Stick Duo”
media slot until it clicks.
Confirm the direction of the “Memory
Stick PRO Duo” media. If you forcibly
insert the “Memory Stick PRO Duo” media
in the wrong direction, the “Memory Stick
PRO Duo” media, “Memory Stick Duo”
media slot, or image data may be damaged.
Close the “Memory Stick Duo” media
cover after inserting the “Memory Stick
PRO Duo” media.
When inserting or ejecting the “Memory
Stick PRO Duo” media, be careful so that the
“Memory Stick PRO Duo” media does not pop
out and drop.
ꢄ0
Checking the media
information
You can check the remaining recordable
time for each recording mode of the
recording media selected on [MOVIE
free and used media space of the recording
media.
Notes
During Easy Handycam operation, you cannot
check the media information. Cancel Easy
Handycam operation.
Touch (HOME)
(MANAGE
MEDIA) [MEDIA INFO].
The remaining recordable time for each
recording mode is displayed.
Tips
You can check the recordable free space, etc., by
touching
at the lower right on the screen.
To turn off the display
Touch
.
Notes
The calculation for recording media space is 1
MB = 1,048,576 bytes. The fractions less than
MB are discarded when the recording media
space is displayed. The displayed size of the
whole hard disk space will be slightly smaller
than the size shown below despite displaying
both free and used hard disk space.
DCR-SR37E/SR47E: 60,000 MB
DCR-SR38E/SR48E: 70,000 MB
DCR-SR57E/SR67E/SR77E/SR87E: 80,000
MB
Since there is a management file area, the used
space is not displayed as 0 MB even if you
perform [MEDIA FORMAT] (p. 62).
Tips
Only the information of the medium selected
Change the medium setting if necessary.
ꢄ1
Deleting all movies
and photos (Formatting)
Formatting deletes all the movies and
photos to recover recordable free space.
Notes
Connect your camcorder to the wall outlet (wall
socket) using AC Adaptor supplied for this
operation (p. 17).
To avoid the loss of important images, you
too) before formatting the recording media.
Protected movies and photos will also be
deleted.
1
2
3
Touch (HOME)
(MANAGE MEDIA) [MEDIA
FORMAT].
Touch the recording media to be
formatted ([HDD] or [MEMORY
STICK]).
Touch [YES] [YES]
.
Notes
While [Executing…] is displayed, do not close
the LCD screen, operate the buttons on the
camcorder, disconnect the AC Adaptor, or eject
the “Memory Stick PRO Duo” media from your
camcorder (The ACCESS/access lamp is lit or
flashing while formatting the medium.).
ꢄꢀ
Preventing data on the
internal hard disk from
being recovered
4
5
Touch [EMPTY].
The [ EMPTY] screen appears.
[
EMPTY] allows you to write
unintelligible data onto the internal hard
disk of the camcorder. In this way, it may
become more difficult to recover any
original data. When you dispose of or
transfer the camcorder, it is recommended
that you perform [ EMPTY].
Touch [YES] [YES]
.
Notes
Notes
If you perform [ EMPTY], all the images are
deleted. To avoid the loss of important images,
Guide too) before performing [ EMPTY].
You cannot perform [ EMPTY] unless you
connect the AC Adaptor to the wall outlet (wall
socket).
Disconnect all cables except the AC Adaptor.
Do not disconnect the AC Adaptor during the
operation.
The actual performing time for [ EMPTY] is
as follows:
DCR-SR37E/SR47E: about 60 minutes
DCR-SR38E/SR48E: about 70 minutes
DCR-SR57E/SR67E/SR77E/SR87E: about 80
minutes
If you stop performing [ EMPTY] while
[Executing…] appears, be sure to complete the
operation by performing [MEDIA FORMAT]
or [ EMPTY] when you use the camcorder
next time.
While performing [ EMPTY], do not apply
any vibrations or shocks to your camcorder.
1
Connect the AC Adaptor to the
DC IN jack on the camcorder and
the wall outlet (wall socket).
2
3
Open the LCD screen to turn on
your camcorder.
Touch (HOME)
(MANAGE MEDIA) [MEDIA
FORMAT] [HDD].
The [ FORMAT] screen appears.
ꢄꢁ
Customizing your camcorder
MOVIE SETTINGS (Items for recording movies)
The default settings are marked with .
REC MODE (Recording mode)
Steps
(HOME)
(SETTINGS) [MOVIE SETTINGS] [REC MODE] a desired setting
You can select a recording mode to record movies from 3 levels.
Records in high quality mode (9M (HQ)).
HQ (
SP (
LP (
)
Records in standard quality mode (6M (SP)).
Increases the recording time (Long Play) (3M (LP)).
)
)
Notes
If you record in the LP mode, the quality of movies may be degraded, or scenes with quick movements
may appear with block noise when you play back the image.
Tips
You can select the [REC MODE] for each recording media separately.
Figures such as 9M in the table show the average bit rate. M stands for Mbps.
AUDIO MODE (DCR-SR57E/SR67E/SR77E/SR87E)
You can change the recording sound format.
Steps
(HOME)
(SETTINGS) [MOVIE SETTINGS] [AUDIO MODE] a desired
setting
5.1ch SURROUND
Records sound in 5.1ch surround.
Records sound in 2ch stereo.
(
)
2ch STEREO
(
)
ꢄꢂ
WIDE SELECT
You can select the horizontal to vertical ratio according to the TV connected. Refer also to the
instruction manuals supplied with your TV.
Steps
(HOME)
(SETTINGS) [MOVIE SETTINGS] [WIDE SELECT] a desired
setting
16:9 WIDE
Records movies to the full screen on a 16:9 (wide) TV screen.
Records movies to the full screen on a 4:3 TV screen.
4:3 (
)
Notes
Set [TV TYPE] correctly according to the TV connected for playback (p. 74).
DIGITAL ZOOM
You can select the maximum zoom level in case you want to zoom to a level greater than
following optical zoom during recording. Note that the image quality decreases when you use
the digital zoom.
DCR-SR37E/SR38E/SR47E/SR48E/SR57E/SR67E: 60 ×
DCR-SR77E/SR87E: 25 ×
Steps
(HOME)
(SETTINGS) [MOVIE SETTINGS] [DIGITAL ZOOM] a desired
setting
The right side of the bar shows the digital zooming factor. The
zooming zone appears when you select the zooming level.
DCR-SR37E/SR38E/SR47E/SR48E/SR57E/SR67E
OFF
Up to 60 × zoom is performed optically.
Up to 60 × zoom is performed optically, and after that, up to 120 × zoom is
performed digitally.
120 ×
Up to 60 × zoom is performed optically, and after that, up to 2000 × zoom is
performed digitally.
2000 ×
DCR-SR77E/SR87E
OFF
Up to 25 × zoom is performed optically.
Up to 25 × zoom is performed optically, and after that, up to 50 × zoom is
performed digitally.
50 ×
Up to 25 × zoom is performed optically, and after that, up to 2000 × zoom is
performed digitally.
2000 ×
ꢄꢃ
STEADYSHOT
You can compensate for camera shake.
Set [ STEADYSHOT] to [OFF] ( ) when using a tripod (sold separately), then the image
becomes natural.
Steps
(HOME)
(SETTINGS) [MOVIE SETTINGS]
[
STEADYSHOT] a desired
setting
ON
The SteadyShot function is used.
The SteadyShot function is not used.
OFF (
)
AUTO SLW SHUTTR (Auto Slow Shutter)
When recording in dark places, the shutter speed is automatically reduced to 1/25 second.
Steps
(HOME)
desired setting
(SETTINGS) [MOVIE SETTINGS] [AUTO SLW SHUTTR]
a
ON
The Auto Slow Shutter function is used.
The Auto Slow Shutter function is not used.
OFF
GUIDEFRAME
You can display the frame and check that the subject is horizontal or vertical.
The frame is not recorded. Press DISP to make the frame disappear.
Steps
(HOME)
(SETTINGS) [MOVIE SETTINGS] [GUIDEFRAME] a desired
setting
OFF
ON
Does not display the guide frame.
Displays the guide frame.
Tips
Positioning the subject at the cross point of the guide frame makes a balanced composition.
ꢄꢄ
REMAINING SET
Steps
(HOME)
desired setting
(SETTINGS) [MOVIE SETTINGS]
[
REMAINING SET]
a
ON
Always displays the remaining recording media indicator.
Displays the remaining recording time of movies for about 8 seconds in
situations such as those described below.
When your camcorder recognizes the remaining recording media capacity
AUTO
while the
(Movie) lamp lights up
When you press DISP to switch the indicator from off to on while the
(Movie) lamp lights up
When you select the movie recording mode on the HOME MENU
Notes
When the remaining recordable time for movies is less than 5 minutes, the indicator stays on the screen.
FACE SET
Steps
(HOME)
(SETTINGS) [MOVIE SETTINGS]
[
FACE SET] a desired
setting
The camcorder detects faces automatically and displays the Face Index
screen (p. 38).
Face icons and their meanings
ON
: This icon appears when the setting is [ON].
: This icon flashes when your camcorder detects a face. The icon stops
flashing when the face is recorded in Face Index.
: This icon appears when faces cannot be recorded in Face Index.
OFF
Does not display the Face Index screen.
Notes
The number of faces detected in a movie is limited.
ꢄ7
PHOTO SETTINGS (Items for recording photos)
The default settings are marked with .
IMAGE SIZE
You can select a photo size to be shot.
Steps
(HOME)
(SETTINGS) [PHOTO SETTINGS]
[
IMAGE SIZE] a desired
setting
DCR-SR37E/SR38E/SR47E/SR48E/SR57E/SR67E
Records photos clearly (640 × 480).
VGA(0.3M) (
)
Allows the maximum number of still images to be recorded (640 × 360).
The image size is set to [ 0.2M] automatically in the 16:9 (wide) aspect
ratio.
0.2M (
)
DCR-SR77E/SR87E
Records photos clearly (1,152 × 864).
1.0M (
0.7M (
VGA(0.3M) (
Notes
)
Records photos clearly in the 16:9 (wide) ratio (1,152 × 648).
The image size is set to [ 0.7M] automatically in the 16:9 (wide) aspect
ratio.
)
Allows the maximum number of photos to be recorded (640 × 480).
)
FILE NO. (File number)
You can select the way to assign file number of photos.
Steps
(HOME)
(SETTINGS) [PHOTO SETTINGS] [FILE NO.] a desired setting
Assigns file numbers of photos in sequence.
The file number becomes larger each time you record a photo.
Even if the “Memory Stick PRO Duo” media is replaced with another one,
the file number is assigned in sequence.
Assigns file numbers in sequence, following the largest file number existing
on the current recording medium.
When the “Memory Stick PRO Duo” media is replaced with another one,
the file number is assigned for each “Memory Stick PRO Duo” media.
SERIES
RESET
ꢄ8
AUTO SLW SHUTTR (Auto Slow Shutter)
When recording in dark places, the shutter speed is automatically reduced to 1/25 second.
Steps
(HOME)
desired setting
(SETTINGS) [PHOTO SETTINGS] [AUTO SLW SHUTTR]
a
ON
The Auto Slow Shutter function is used.
The Auto Slow Shutter function is not used.
OFF
GUIDEFRAME
You can display the frame and check that the subject is horizontal or vertical.
The frame is not recorded. Press DISP to make the frame disappear.
Steps
(HOME)
(SETTINGS) [PHOTO SETTINGS] [GUIDEFRAME] a desired
setting
OFF
ON
Does not display the guide frame.
Displays the guide frame.
Tips
Positioning the subject at the cross point of the guide frame makes a balanced composition.
ꢄ9
VIEW IMAGES SET (Items to customize the display)
The default settings are marked with .
DATA CODE
During playback, your camcorder displays the information (data code) recorded automatically
at the time of recording.
Steps
(HOME)
(SETTINGS) [VIEW IMAGES SET] [DATA CODE] a desired
setting
OFF
Data code is not displayed.
Displays the date and time.
Displays camera setting data.
DATE/TIME
CAMERA DATA
DATE/TIME
Date
Time
CAMERA DATA
Movie
Photo
SteadyShot off
Brightness
White balance
Gain
Shutter speed
Aperture value
Exposure
70
Tips
The data code is displayed on the TV screen if you connect your camcorder to a TV.
Depending on the recording media condition, bars [--:--:--] appear.
71
SOUND/DISP SET (Items to adjust the sound and the screen)
The default settings are marked with .
VOLUME
You can adjust the volume of playback sound.
Steps
(HOME)
(louder)
(SETTINGS) [SOUND/DISP SET] [VOLUME]
(quieter)/
BEEP
Steps
(HOME)
(SETTINGS) [SOUND/DISP SET] [BEEP] a desired setting
ON
A melody sounds when you start/stop recording, or operate the touch panel.
Cancels the melody.
OFF
LCD BRIGHT
You can adjust the brightness of the LCD screen.
Steps
(HOME)
(brighter)
(SETTINGS) [SOUND/DISP SET] [LCD BRIGHT]
(darker)/
Tips
This adjustment does not affect the recorded images in any way.
LCD BL LEVEL (LCD back light level)
You can adjust the brightness of the LCD screen’s backlight.
Steps
(HOME)
(SETTINGS) [SOUND/DISP SET] [LCD BL LEVEL] a desired
setting
NORMAL
BRIGHT
Standard brightness.
Brightens the LCD screen.
Notes
When you connect your camcorder to the wall outlet (wall socket) using the supplied AC Adaptor,
[BRIGHT] is automatically selected for the setting.
When you select [BRIGHT], battery life is slightly reduced during recording.
7ꢀ
If you open the LCD panel 180 degrees to face the screen outside and close the LCD panel to the
camcorder body, the setting becomes [NORMAL] automatically.
Tips
This adjustment does not affect the recorded images in any way.
LCD COLOR
You can adjust the color of the LCD screen.
Steps
(HOME)
(SETTINGS) [SOUND/DISP SET] [LCD COLOR]
(lower
intensity)/
(higher intensity)
Tips
This adjustment does not affect the recorded images in any way.
7ꢁ
OUTPUT SETTINGS (Items for when connected to a TV)
The default settings are marked with .
TV TYPE
See page 43.
DISP OUTPUT (Display output)
You can set where the screen displays are to be output.
Steps
(HOME)
(SETTINGS) [OUTPUT SETTINGS] [DISP OUTPUT] a desired
setting
LCD PANEL
Shows displays such as the time code on the LCD screen.
Shows displays such as the time code on the LCD screen, and on the TV
screen.
V-OUT/PANEL
7ꢂ
CLOCK/ LANG (Items to set clock and language)
The default settings are marked with .
CLOCK SET
See page 19.
AREA SET
You can adjust a time difference without stopping the clock. Set your local area when using
your camcorder in other time zones. Refer to the world time difference on page 97.
Steps
(HOME)
using
(SETTINGS) [CLOCK/ LANG] [AREA SET] set your local area
/
SUMMERTIME
You can change this setting without stopping the clock. Set to [ON] to move the time forward
1 hour.
Steps
(HOME)
(SETTINGS) [CLOCK/ LANG] [SUMMERTIME] a desired
setting
OFF
ON
Does not set the summertime.
Sets the summertime.
LANGUAGE SET
You can select the language to be used on the LCD screen.
Steps
(HOME)
(SETTINGS) [CLOCK/ LANG]
[
LANGUAGE SET] a desired
setting
Tips
Your camcorder offers [ENG[SIMP]] (simplified English) for when you cannot find your native tongue
among the options.
7ꢃ
GENERAL SET (Other setup items)
The default settings are marked with .
DEMO MODE
When your camcorder is connected to a wall outlet (wall socket), a demonstration movie
appear about 10 minutes after you turn on the (Movie) lamp by pressing MODE.
Steps
(HOME)
(SETTINGS) [GENERAL SET] [DEMO MODE] a desired setting
ON
The demonstration appears.
OFF
The demonstration does not appear.
Tips
When you set this item to [ON] and touch
The demonstration will be suspended:
When you press START/STOP
, the demonstration starts playing.
When you touch the screen during the demonstration (The demonstration starts again after about 10
minutes.)
When you turn on the
(Photo) lamp
When you press
(HOME) or (VIEW IMAGES)
CALIBRATION
See page 102.
A.SHUT OFF (Auto shut off)
You can set your camcorder to turn off automatically when you do not operate your
camcorder for more than about 5 minutes.
Steps
(HOME)
(SETTINGS) [GENERAL SET] [A.SHUT OFF] a desired setting
5min
The camcorder turns off automatically.
NEVER
The camcorder does not turn off automatically.
Notes
When you connect your camcorder to a wall outlet (wall socket), [A.SHUT OFF] is automatically set to
[NEVER].
7ꢄ
POWER ON BY LCD
You can set your camcorder to turn on and off when you open and close the LCD screen.
Steps
(HOME)
(SETTINGS) [GENERAL SET] [POWER ON BY LCD] a desired
setting
ON
The camcorder turns on and off when the LCD screen opens and closes.
The camcorder does not turn on and off when the LCD screen opens and
closes.
OFF
DROP SENSOR
Your camcorder detects that it is dropping, and protects the internal hard disk.
Steps
(HOME)
(SETTINGS) [GENERAL SET] [DROP SENSOR] a desired setting
Activates the drop sensor. When it is detected that the camcorder is
dropping, you may not be able to record or play back images correctly, to
ON
protect the internal hard disk. When dropping is detected,
appears.
Deactivates the drop sensor.
OFF (
)
Notes
Set the drop sensor to [ON] when you use the camcorder. Otherwise, if you drop the camcorder, you may
damage the internal hard disk.
In a non-gravity situation, the drop sensor activates. When you record images during an activity such as
roller-coasting or skydiving, you can set [DROP SENSOR] to [OFF] so as not to activate the drop sensor.
77
Functions set in the OPTION MENU
Items you can set only on the
OPTION MENU will be described below.
The default settings are marked with .
SPOT MTR/FCS
You can adjust the brightness and focus for the selected subject simultaneously. This function
Steps
In recording mode, (OPTION)
[SPOT MTR/FCS] touch the subject you
want to adjust the brightness and focus on [END]
To adjust the brightness and focus automatically, touch [AUTO].
Notes
[EXPOSURE] and [FOCUS] are automatically set to [MANUAL].
SPOT METER (Flexible spot meter)
You can adjust and fix the exposure to the subject, so that it is recorded in suitable brightness
even when there is strong contrast between the subject and the background, such as subjects
in the spotlight on stage.
Steps
In recording mode, (OPTION)
[SPOT METER] touch the point where
you want to fix and adjust the exposure on the screen [END]
To return the setting to automatic exposure, touch [AUTO].
Notes
[EXPOSURE] is automatically set to [MANUAL].
78
SPOT FOCUS
You can select and adjust the focal point to aim it at a subject not located at the center of the
screen.
Steps
In recording mode, (OPTION)
focused within the frame on the screen [END]
[SPOT FOCUS] touch the point to be
To adjust the focus automatically, touch [AUTO].
Notes
[FOCUS] is automatically set to [MANUAL].
TELE MACRO
This is useful to shoot small subjects, such as flowers or insects. You can blur out backgrounds
and the subject stands out clearer.
Steps
In recording mode, (OPTION)
[TELE MACRO] a desired setting
Cancels TELE MACRO. (TELE MACRO is also canceled when you move the
zoom lever to the W side.)
OFF
the T (telephoto) side automatically
and allows recording subjects at a
close distance as follows:
DCR-SR37E/SR38E/SR47E/SR48E/
SR57E/SR67E: down to about 50 cm
(19 3/4 in.)
DCR-SR77E/SR87E: down to about
38 cm (15 in.)
ON (
)
Notes
When recording a distant subject, focusing may be difficult and can take some time.
79
EXPOSURE
You can fix the brightness of a picture manually. Adjust the brightness when the subject is too
bright or too dark.
Steps
In recording mode, (OPTION)
[EXPOSURE] [MANUAL]
(darker)/
(brighter)
To adjust the exposure automatically, touch [AUTO].
FOCUS
You can adjust the focus manually. You can select this function also when you want to focus
on a certain subject intentionally.
Steps
In recording mode, (OPTION)
[FOCUS] [MANUAL]
(focusing on
close subjects)/ (focusing on distant subjects)
To adjust the focus automatically, touch [AUTO].
Notes
When you set [FOCUS] to [MANUAL], appears.
The minimum possible distance between camcorder and subject while maintaining sharp focus is about
1 cm (about 13/32 in.) for wide angle and about 150 cm (about 59 1/8 in.) (DCR-SR37E/SR38E/SR47E/
SR48E/SR57E/SR67E)/80 cm (about 31 1/2 in.) (DCR-SR77E/SR87E) for telephoto.
Tips
appears when the focus cannot be adjusted any closer, and appears when the focus cannot be
adjusted farther away.
It is easier to focus on the subject by moving the power zoom lever towards T (telephoto) to adjust the
focus, then towards W (wide angle) to adjust the zoom for recording. When you want to record a subject
at close range, move the power zoom lever to W (wide angle), then adjust the focus.
The focal distance information (distance at which the subject is focused on; used as a guide if it is dark
and focus adjustment is difficult) appears for a few seconds in the following cases. (This information will
not display correctly if a conversion lens (sold separately) is being used.)
When the focus mode is switched from automatic to manual
When you set focus manually
80
SCENE SELECTION
You can record images effectively in various situations.
Steps
In recording mode, (OPTION)
[SCENE SELECTION] a desired setting
Automatically records images effectively without the [SCENE SELECTION]
function.
AUTO
Maintains the darkening atmosphere of the distant
surroundings in twilight scenes.
TWILIGHT* (
)
Maintains the dim atmosphere of a candlelit scene.
CANDLE ( )
SUNRISE&SUNSET*
Reproduces the atmosphere of scenes such as sunsets or
sunrises.
(
)
Takes spectacular shots of fireworks.
FIREWORKS* (
)
Shoots distant subjects clearly. This setting also prevents
your camcorder from focusing on glass or metal mesh in
windows between the camcorder and the subject.
LANDSCAPE*(
PORTRAIT (Soft
)
Brings out the subject such as people or flowers while
creating a soft background.
portrait) (
)
Prevents people’s faces from appearing excessively white
when subjects are lit by strong light.
SPOTLIGHT**(
)
Select to minimize shake when shooting fast moving
subjects.
SPORTS** (
BEACH** (
SNOW** (
)
Takes the vivid blue of the ocean or a lake.
Takes bright pictures of a white landscape.
)
)
*
Adjusted to focus on subjects farther away only.
** Adjusted not to focus on subjects a short distance away.
81
Notes
If you set [SCENE SELECTION], [WHITE BAL.] setting is canceled.
WHITE BAL. (White balance)
You can adjust the color balance to the brightness of the recording environment.
Steps
In recording mode, (OPTION)
[WHITE BAL.] a desired setting
AUTO
The white balance is adjusted automatically.
The white balance is appropriately adjusted for the following recording
conditions:
Outdoors
OUTDOOR (
)
Night views, neon signs and fireworks
Sunrise or sunset
Under daylight fluorescent lamps
The white balance is appropriately adjusted for the following recording
conditions:
Indoors
INDOOR ()
At party scenes or studios where the lighting conditions change quickly
Under video lamps in a studio, or under sodium lamps or incandescent-
like color lamps
The white balance will be adjusted according to the ambient light.
Touch [ONE PUSH].
Frame a white object such as a piece of paper, to fill the screen under the
same lighting conditions as you will shoot the subject.
ONE PUSH (
)
Touch [
flashes quickly. When the white balance has been adjusted and stored in
the memory, the indicator stops flashing.
].
Notes
Set [WHITE BAL.] to [AUTO] or adjust the color in [ONE PUSH] under white or cool white fluorescent
lamps.
When you select [ONE PUSH], keep framing white objects while
flashes slowly if [ONE PUSH] could not be set.
is flashing quickly.
When [ONE PUSH] was selected, if
[AUTO].
keeps flashing after touching
, set [WHITE BAL.] to
If you set [WHITE BAL.], [SCENE SELECTION] is set to [AUTO].
8ꢀ
Tips
If you have changed the battery pack while [AUTO] was selected, or taken your camcorder outdoors after
inside use (or vice versa), select [AUTO] and aim your camcorder at a nearby white object for about 10
seconds for better color balance adjustment.
When the white balance has been set with [ONE PUSH], if the lighting conditions changed by bringing
your camcorder outdoors from inside the house, or vice versa, you need to redo the [ONE PUSH]
procedure to readjust the white balance.
FADER
You can record a transition with the following effects adding to the interval between scenes.
Select the desired effect in [STBY] (to fading in) or [REC] (to fading out) mode.
Steps
In recording mode, (OPTION)
[FADER] a desired setting
OFF
Does not use an effect.
Out
In
In
WHITE FADER
Fades in/out with the white effect.
Fades in/out with the black effect.
Out
BLACK FADER
To cancel the fader before starting the operation, touch [OFF].
Tips
When you press START/STOP, the setting is cleared.
BLT-IN ZOOM MIC (Built-in zoom microphone)
You can record a movie with directional sound as you zoom in or out.
Steps
In recording mode, (OPTION)
[BLT-IN ZOOM MIC] a desired setting
OFF
The microphone does not record sound following zooming in or out.
The microphone records sound following
zooming in or out.
ON (
)
8ꢁ
MICREF LEVEL (Microphone reference level)
You can select the microphone level for recording sound.
Steps
In recording mode, (OPTION)
[MICREF LEVEL] a desired setting
NORMAL
Records various ambient sounds, converting them into the appropriate level.
Records ambient sound faithfully. Select [LOW] when you want to record
an exciting and powerful sound in a concert hall, etc. (This setting is not
suitable for recording conversations.)
LOW (
)
SELF-TIMER
Press PHOTO to start the count down. A photo is recorded after about 10 seconds.
Steps
In recording mode, (OPTION)
[SELF-TIMER] a desired setting
OFF
Cancels the self-timer.
Starts the self-timer recording. To cancel the recording, touch [RESET].
ON (
)
8ꢂ
Troubleshooting
socket). Connect it to the wall outlet (wall
socket) (p. 16).
Troubleshooting
If you run into any problems using your
camcorder, use the following list to
troubleshoot the problem. If the problem
persists, disconnect the power source and
contact your Sony dealer.
The camcorder does not operate even
when the power is set to on.
It takes a few seconds for your camcorder to
be ready to shoot after the power is turned on.
This is not a malfunction.
Disconnect the AC Adaptor from the wall
outlet (wall socket) or remove the battery
pack, then reconnect it after about 1 minute.
If the functions still do not work, press RESET
RESET, all settings, including the clock setting,
are reset.)
The temperature of your camcorder is
extremely high. Turn off your camcorder and
leave it for a while in a cool place.
The temperature of your camcorder is
extremely low. Leave your camcorder with the
power of your camcorder on. Turn off your
camcorder and take it to a warm place. Leave
the camcorder there for a while, then turn on
your camcorder.
Playing back images stored on “Memory Stick
Editing movies/photos on your camcorder
Functions that cannot be used simultaneously
Notes before sending your camcorder
for repair
Buttons do not work.
Your camcorder may be required to initialize or
change the current hard disk of your camcorder,
depending on the problem. In the event of this,
the data stored on the hard disk will be deleted.
Be sure to save the data on the internal hard
disk on other media (backup) before sending
Guide too). We will not compensate you for any
loss of hard disk data.
During Easy Handycam operation, the
available.
The (OPTION) button is not displayed.
The OPTION MENU cannot be used during
Easy Handycam operation.
During repair, we may check a minimum
amount of data stored on the hard disk in order
to investigate the problem. However, your Sony
dealer will neither copy nor retain your data.
The menu settings have changed
automatically.
During Easy Handycam operation, nearly all
the menu items will be automatically set to the
default settings.
Some menu items, such as [ IMAGE SIZE],
retain the settings that were made before Easy
Handycam operation.
Overall operations/Easy Handycam
operation
During Easy Handycam operation, some
menu items are fixed as follows.
The power does not turn on.
Attach a charged battery pack to the
camcorder (p. 16).
The plug of the AC Adaptor has been
disconnected from the wall outlet (wall
[REC MODE]: [SP]
[DATA CODE]: [DATE/TIME]
8ꢃ
Some menu items retain the setting made
during Easy Handycam operation even after
Easy Handycam operation is finished.
The following items return to the default
settings in more than 12 hours after you close
the LCD screen.
The CHG (charge) lamp flashes while the
battery pack is being charged.
Attach the battery pack to the camcorder
disconnect the AC Adaptor from the wall
outlet (wall socket) and contact your Sony
dealer. The battery pack may be damaged.
[DROP SENSOR]
[SPOT MTR/FCS]
[SPOT METER]
[SPOT FOCUS]
[EXPOSURE]
[FOCUS]
[SCENE SELECTION]
[WHITE BAL.]
[BLT-IN ZOOM MIC]
[MICREF LEVEL]
Back light
The remaining battery time indicator does
not indicate the correct time.
The ambient temperature is too high or too
low. This is not a malfunction.
The battery pack has not been charged
enough. Fully charge the battery again. If the
problem persists, replace the battery pack with
a new one (p. 101).
The indicated time may not be correct
depending on the environment of use.
Your camcorder gets warm.
Your camcorder may become warm during
operation. This is not a malfunction.
The battery pack is quickly discharged.
The ambient temperature is too high or low.
This is not a malfunction.
The battery pack has not been charged
enough. Fully charge the battery again. If the
problem persists, replace the battery pack with
a new one (p. 101).
Batteries/power sources
The power abruptly turns off.
Use the AC Adaptor.
In the default setting, when about 5 minutes
have elapsed while you do not operate your
camcorder, the camcorder is automatically
turned off (A.SHUT OFF). Change the setting
power again.
LCD screen
Menu items are grayed out.
You cannot select grayed items in the current
recording/playback situation.
There are some functions you cannot activate
simultaneously (p. 89).
The CHG (charge) lamp does not light
while the battery pack is being charged.
Attach the battery pack to the camcorder
correctly (p. 16).
Connect the power cord (mains lead) to the
wall outlet (wall socket) properly.
The buttons do not appear on the touch
panel.
Touch the LCD screen lightly.
The buttons on the touch panel do not
work correctly or do not work at all.
Adjust the touch panel [CALIBRATION]
(p. 102).
8ꢄ
take it to a warm place. Leave the camcorder
there for a while, then turn on the camcorder.
“Memory Stick PRO Duo”media
The ACCESS/access lamp remains lit or
flashing even if recording was stopped.
Operations using the “Memory Stick PRO
Duo”media cannot be performed.
Your camcorder is recording the scene you
have just shot on the recording media.
If you use “Memory Stick PRO Duo” media
formatted on a computer, format it again on
your camcorder (p. 62).
The imaging field looks different.
Images stored on the “Memory Stick PRO
Duo”media cannot be deleted.
The imaging field may look different
depending on the condition of your
camcorder. This is not a malfunction.
The maximum number of images that you can
delete on the index screen at one time is 100.
You cannot delete the protected images.
The actual recording time for movies is
less than the expected recording time of
the recording media.
The data file name is not indicated
correctly or flashes.
Depending on the recording conditions, the
time available for recording may be shorter, for
example when recording a fast moving object,
etc. (p. 94).
The file is damaged.
The file format is not supported by your
camcorder (p. 100).
The camcorder stops operating.
Recording
The temperature of your camcorder is
extremely high. Turn off your camcorder and
leave it for a while in a cool place.
Refer also to “Memory Stick PRO Duo”
media (p. 87).
The temperature of your camcorder is
extremely low. Turn off your camcorder and
take it to a warm place. Leave the camcorder
there for a while, then turn on the camcorder.
If you keep applying vibration on the
camcorder, recording may stop.
Pressing START/STOP or PHOTO does not
record images.
The playback screen is displayed. Press MODE
to turn on the
(p. 28, 30).
(Movie) or (Photo) lamp
Your camcorder is recording the image you
have just shot on the recording media. You
cannot make new recording during this
period.
The recording media is full. Delete
unnecessary images (p. 44).
Total number of movie scenes or photos
exceeds the recordable capacity of your
(p. 44).
There is a time difference between the
point when START/STOP is pressed and
the point that the recording movie is
started or stopped actually.
On your camcorder, there may be a slight
time difference between the point where you
press START/STOP and the actual point that
recording movie starts/stops. This is not a
malfunction.
you may not record images.
The auto focus does not function.
The temperature of your camcorder is
extremely high. Turn off your camcorder and
leave it for a while in a cool place.
The temperature of your camcorder is
extremely low. Turn off your camcorder and
The recording conditions are not suitable for
auto focus. Adjust the focus manually (p. 80).
87
Photos recorded on other devices may not be
played back. This is not a malfunction.
SteadyShot does not function.
Even if [ STEADYSHOT] is set to
[ON], your camcorder may not be able to
compensate for excessive vibrations.
is indicated on an image on the
VISUAL INDEX screen.
This may appear on an image recorded on
other devices, edited on a computer, etc.
You removed the AC Adaptor or the battery
pack before the ACCESS/access lamp is turned
off after recording. This may damage your
A vertical band appears when recording
candlelight or electric light in the dark.
This occurs when the contrast between the
subject and the background is too high. This is
not a malfunction.
image data and
is displayed.
is indicated on an image on the
VISUAL INDEX screen.
A vertical white line may appear on an
image taken in bright light.
The image data base file may be damaged.
Check the data base file by touching
This phenomenon is called the smear effect.
This is not a malfunction.
(HOME)
(MANAGE MEDIA)
[REPAIR IMG.DB F.] the recording
medium. If it still appears, delete the image
Black bands appear when you record a TV
screen or computer screen.
with
(p. 44).
No sound or only a quiet sound is heard
during playback.
Undesirable flicker occurs.
Sound is not output when the LCD screen is
closed. Open the LCD screen.
When you record sound with [MICREF
sound may be difficult to hear.
This occurs when recording images under a
fluorescent lamp, sodium lamp, or mercury
lamp. This is not a malfunction.
[LCD BL LEVEL] cannot be adjusted.
You cannot adjust [LCD BL LEVEL] when:
The LCD panel is closed on your camcorder
with the LCD screen facing out.
Left and right sound will be heard
unbalanced when playing back movies on
computers or other devices.
The power is supplied from the AC Adaptor.
This happens when sound recorded in 5.1ch
surround is converted to 2ch (normal stereo
sound) by a computer or other device. This
is not a malfunction (DCR-SR57E/SR67E/
SR77E/SR87E).
Change the sound conversion type (downmix
type) when playing back on 2ch stereo devices.
Refer to the instruction manual supplied with
your playback device for details.
Playback
Images cannot be played back.
Select the recording media you want to
play back by touching (HOME)
(MANAGE MEDIA) [MOVIE MEDIA
SET]/[PHOTO MEDIA SET] (p. 59).
Change the sound to 2ch when creating a disc
using the supplied software “PMB” (DCR-
SR57E/SR67E/SR77E/SR87E).
Record sound with [AUDIO MODE] set to
[2ch STEREO] (DCR-SR57E/SR67E/SR77E/
SR87E) (p. 64).
Photos cannot be played back.
Photos cannot be played back if you have
modified files or folders, or have edited the
data on a computer. (The file name flashes in
that case.) This is not a malfunction.
88
Playing back images stored on
“Memory Stick PRO Duo”media on
other devices
The aspect ratio of the playback is not
correct when connecting your camcorder
to the TV.
Images cannot be played back or the
“Memory Stick PRO Duo”media is not
recognized.
Images are not dubbed correctly.
The A/V connecting cable is not connected
properly. Make sure to connect the cable to the
input jack of another device (p. 56).
The device may not support “Memory Stick
PRO Duo” media.
Functions that cannot be used
simultaneously
Editing movies/photos on your
camcorder
The following list shows examples of
unworkable combinations of functions and
menu items.
Unable to edit.
Unable to edit because of the condition of the
image.
Cannot use
Because of following settings
[SCENE
SELECTION]
[FADER], [TELE MACRO]
Movies cannot be added in the Playlist.
Back light
[SPOT MTR/FCS], [SPOT
METER], [MANUAL]
in [EXPOSURE],
There is no free space in the recording media.
You can add no more than 99 movies to a
Playlist. Erase unnecessary movies from the
Playlist (p. 52).
[FIREWORKS]
You cannot add photos in the Playlist.
Self-diagnosis display/Warning
indicators
A movie cannot be divided.
A movie that is too short cannot be divided.
A protected movie cannot be divided.
If indicators appear on the LCD screen,
check the following.
A photo cannot be captured from a
movie.
If the problem persists even after you
have tried to fix a couple of times, contact
your Sony dealer or local authorized Sony
service facility.
The recording media where you want to save
photos is full.
Connecting/Dubbing to other
devices
You cannot hear the sound on the TV
connected to your camcorder.
C:(or E:) : (Self-diagnosis display)
When you are using the S VIDEO plug,
make sure the red and white plugs of the A/V
connecting cable are connected (p. 42).
C:04:
The battery pack is not an “InfoLITHIUM”
battery pack (H series). Use an
“InfoLITHIUM” battery pack (H series)
(p. 100).
89
Connect the DC plug of the AC Adaptor to the
DC IN jack of your camcorder securely (p. 16).
(Low temperature warning)
Fast flashing
C:13:
/ C:32:
Remove the power source. Reconnect it and
operate your camcorder again.
The temperature of your camcorder is
extremely low. Make the camcorder warm.
E:20:
E:91:
/ E:31:
/ E:94:
/ E:61:
/ E:62:
/
(Warning indicator pertaining to
“Memory Stick PRO Duo”media)
A malfunction that you cannot service has
occurred. Contact your Sony dealer or local
authorized Sony service facility. Inform them
of the 5-digit code, which starts from “E.”
Slow flashing
Free spaces for recording images are running
out. For the type of “Memory Stick” media you
can use with your camcorder, see page 59.
No “Memory Stick PRO Duo” media is
inserted (p. 60).
101-0001 (Warning indicator pertaining
to files)
Slow flashing
Fast flashing
The file is damaged.
The file is unreadable.
There are not enough free spaces for recording
images. After storing the images on other
unnecessary images, or format the “Memory
Stick PRO Duo” media (p. 62).
(Warning on the hard disk of the
camcorder)
The image data base file may be damaged.
Check the data base file by touching
Fast flashing
The hard disk of the camcorder is full.
An error may have occurred with the hard
disk drive in your camcorder.
(HOME)
(MANAGE MEDIA)
[REPAIR IMG.DB F.] the recording
medium.
The “Memory Stick PRO Duo” media is
damaged.
(Battery level warning)
Slow flashing
The battery pack is nearly used up.
Depending on the operating environment or
(Warning indicators pertaining
to “Memory Stick PRO Duo”media
formatting)
battery conditions,
may flash, even if there
are about 20 minutes remaining.
The “Memory Stick PRO Duo” media is
damaged.
The “Memory Stick PRO Duo” media is not
formatted correctly (p. 62).
(High temperature warning)
Slow flashing
The temperature of your camcorder is getting
higher. Turn off your camcorder and leave it
for a while in a cool place.
(Warning indicator pertaining to
incompatible “Memory Stick Duo”media)
Incompatible “Memory Stick Duo” media are
inserted (p. 59).
Fast flashing
The temperature of your camcorder is
extremely high. Turn off your camcorder and
leave it for a while in a cool place.
(Warning indicator pertaining to
the write-protect of the “Memory Stick
PRO Duo”media)
Access to the “Memory Stick PRO Duo” media
was restricted on another device.
90
Data error.
(Warning indicator pertaining to
camera-shake warning)
An error occurred during reading or writing
the internal hard disk of the camcorder. This
may occur when you keep applying shock on
the camcorder.
The camcorder is unsteady, so camera-shake
easily occurs. Hold the camcorder steady with
both hands and record the image. However,
note that the camera-shake warning indicator
does not disappear.
The Image Database File is damaged. Do
you want to create a new file?
(Warning indicator pertaining to drop
sensor)
The image management file is damaged. When
you touch [YES], a new image management
file is created. The old recorded images on the
media cannot be played back (Image files are
not damaged). If you execute [REPAIR IMG.
DB F.] after creating new information, playing
back the old recorded images may become
possible. If it does not work, copy the image
using the supplied software.
and has detected that the camcorder has been
dropped. Therefore, the camcorder is taking
steps to protect the hard disk. Recording/
playback may be disabled as a result.
The drop sensor function does not guarantee
the protection of the hard disk under all
possible situations. Use the camcorder under
stable conditions.
Inconsistencies found in Image Database
File. Do you want to repair the Image
Database File?
The Image Database File is damaged. Do
you want to repair the Image Database
File?
(Warning indicator pertaining to
photo recording)
The recording media is full.
The image management file is damaged, and
you cannot record movies or photos. Touch
[YES] to repair.
You can record photos on “Memory Stick PRO
Duo” media.
Tips
You may hear a melody when some warning
indicators appear on the screen.
Description of warning messages
Buffer overflow
If messages appear on the screen, follow the
instructions.
You cannot record because the drop sensor
senses a drop of the camcorder repeatedly.
If you are at risk of dropping the camcorder
constantly, set [DROP SENSOR] to [OFF],
and you may be able to record the image again
(p. 77).
Recording media
HDD format error.
The internal hard disk of the camcorder
is set differently from the default format.
enable you to use your camcorder. This will
delete all data in the internal hard disk.
91
Other
Recovering data.
Your camcorder tries to recover data
automatically if the data writing was not
performed properly.
No further selection is possible.
You can add no more than 99 movies to a
Playlist.
You can select 99 or only 100 images at one
time for:
Cannot recover data.
Writing data onto the recording media of the
camcorder has failed. Attempts were made to
recover the data, but they were unsuccessful.
Deleting images
Protecting images, or releasing the protection
Dubbing movies
Copying photos
Editing Playlists
Reinsert the Memory Stick.
Reinsert the “Memory Stick PRO Duo” media
a few times. If even then the indicator flashes,
the “Memory Stick PRO Duo” media could
be damaged. Try with another “Memory Stick
PRO Duo” media.
Data protected.
You tried to delete protected data. Release the
protection of the data.
This Memory Stick is not formatted
correctly.
Check the format, then format the “Memory
Stick PRO Duo” media with your camcorder if
necessary (p. 62).
Still picture folder is full. Cannot record
still pictures.
You cannot create folders exceeding
999MSDCF. You cannot create or delete
created folders using your camcorder.
Format the “Memory Stick PRO Duo” media
This Memory Stick may not be able to
record or play movies.
Use “Memory Stick” media recommended for
your camcorder (p. 59).
This Memory Stick may not be able to
record or play images correctly.
Use “Memory Stick” media recommended for
your camcorder (p. 59).
Do not eject the Memory Stick during
writing. Data may be damaged.
Reinsert the “Memory Stick PRO Duo” media,
and follow the instructions on the LCD screen.
9ꢀ
Additional information
(unit: minute)
Typical recording
time
Recording time of
movies/number of
recordable photos
Battery pack
Continuous
recording time
155
330
745
NP-FH50
NP-FH70
NP-FH100
70
155
350
Expected time of recording and
playback with each battery pack
DCR-SR77E/SR87E:
(unit: minute)
Recording time
Battery pack
Continuous
recording time
140
Typical recording
time
Approximate time available when you use a
fully charged battery pack.
NP-FH50
(supplied)
65
Internal.hard.disk
NP-FH70
NP-FH100
300
680
140
320
DCR-SR37E/SR38E/SR47E/SR48E/
SR57E/SR67E:
Each recording time is measured when the
[REC MODE] is set to SP.
Typical recording time shows the time when
you repeat recording start/stop, switching the
MODE lamp, and zooming.
Times measured when using the camcorder at
25 C (77 ˚F) (10 C to 30 C (50 ˚F to 86 ˚F) is
recommended).
The recording and playback time will be
shorter when you use your camcorder in low
temperatures.
(unit: minute)
Typical recording
time
Battery pack
Continuous
recording time
90
NP-FH30
(supplied)
NP-FH50
NP-FH70
NP-FH100
45
145
315
710
70
155
355
DCR-SR77E/SR87E:
The recording and playback time will be shorter
depending on the conditions under which you
use your camcorder.
(unit: minute)
Typical recording
time
Battery pack
Continuous
recording time
130
Playing time
Approximate time available when you use a
fully charged battery pack.
NP-FH50
(supplied)
NP-FH70
65
280
625
140
310
NP-FH100
DCR-SR37E/SR38E/SR47E/SR48E/
SR57E/SR67E:
“Memory.Stick.PRO.Duo”.media
(unit: minute)
Battery pack
NP-FH30
(supplied)
DCR-SR37E/SR38E/SR47E/SR48E/
SR57E/SR67E:
105
120
170
195
370
415
(unit: minute)
NP-FH50
Battery pack
Continuous
recording time
Typical recording
time
NP-FH70
NP-FH30
(supplied)
95
45
9ꢁ
* You can change the recording sound format on
[AUDIO MODE] (p. 64).
(unit: minute)
Battery pack
Tips
NP-FH100
830
925
You can record movies of a maximum of 9,999
scenes.
The maximum continuous recording time of
movies is approximately 13 hours.
Your camcorder uses the VBR (Variable Bit
Rate) format to automatically adjust image
quality to suit the recording scene. This
technology causes fluctuations in the recording
time of the media. Movies containing quickly
moving and complex images are recorded at
a higher bit rate, and this reduces the overall
recording time.
DCR-SR77E/SR87E:
(unit: minute)
Battery pack
NP-FH50
(supplied)
170
195
370
415
830
925
NP-FH70
NP-FH100
“Memory Stick PRO Duo”media
Top: Internal hard disk
Bottom: “Memory Stick PRO Duo” media
DCR-SR37E/SR38E/SR47E/SR48E:
(unit: minute)
Expected recording time of movies
Internal hard disk
HQ
SP
LP
512MB
1GB
6
(5)
10
(10)
25
(25)
55
(50)
9
(5)
20
(10)
40
(25)
80
(50)
20
(10)
40
(25)
85
(55)
170
(110)
DCR-SR37E/SR47E:
(unit: hour minute)
2GB
Recording mode
[HQ]
[SP]
Recording time
15 h 10 m
21 h 50 m
45 h 40 m
4GB
[LP]
8GB
115
(105)
170
(105)
355
(230)
DCR-SR38E/SR48E:
16GB
235
340
715
(210)
(210)
(460)
(unit: hour minute)
Recording time
Recording mode
[HQ]
[SP]
DCR-SR57E/SR67E/SR77E/SR87E:
17 h 40 m
25 h 30 m
53 h 20 m
(unit: minute)
LP LP
(5.1ch)** (2ch)**
HQ
SP
[LP]
512MB
1GB
6
9
15
20
DCR-SR57E/SR67E/SR77E/SR87E:
(5)
(5)
(10)
(10)
(unit: hour minute)
Recording time
10
(10)
25
(25)
55
(50)
20
(10)
40
(25)
80
(50)
35
(25)
80
(50)
160
(105)
40
(25)
85
(55)
170
(110)
Recording mode
[HQ]
[SP]
[LP](5.1ch)*
[LP](2ch)*
19 h 40 m
29 h 10 m
56 h
2GB
4GB
61 h
9ꢂ
(unit: minute)
LP LP
(5.1ch)** (2ch)**
1.0M
1,152 × 864
HQ
SP
2GB
4GB
8GB
16GB
3700
7200
14500
29500
8GB
115
(100)
230
(205)
170
(100)
340
(205)
325
(215)
355
(230)
16GB
655
(435)
715
(460)
** You can change the recording sound format on
[AUDIO MODE] (p. 64).
The number of recordable photos shown is for
the maximum image size of your camcorder.
The actual number of recordable photos is
displayed on the LCD screen during recording
(p. 8).
Notes
Numbers in the table are based on using Sony
“Memory Stick PRO Duo” media.
The recordable time may vary depending on the
recording and subject conditions, [REC MODE]
The number in ( ) is the minimum recordable
time.
Notes
Numbers in the table are based on using Sony
“Memory Stick PRO Duo” media. The number
of recordable photos may vary depending
on the recording conditions, and the type of
“Memory Stick” media.
Expected number of recordable
photos
Tips
You can also use “Memory Stick Duo” media
with a capacity of under 512 MB for recording
photos.
Internal hard disk
You can record the maximum 9,999 photos.
“Memory Stick PRO Duo”media
DCR-SR37E/SR38E/SR47E/SR48E/
SR57E/SR67E:
VGA
640 × 480
512MB
1GB
2800
5700
2GB
4GB
8GB
16GB
11500
23000
47000
94000
DCR-SR77E/SR87E:
1.0M
1,152 × 864
512MB
1GB
870
1800
9ꢃ
Using your camcorder
abroad
Power supply
You can use your camcorder in any
countries/regions using the AC Adaptor
supplied with your camcorder within the
AC 100 V to 240 V, 50 Hz/60 Hz range.
On TV color systems
Your camcorder is a PAL-system-based
camcorder. If you want to view the playback
image on a TV, it must be a PAL-system-
based TV with an AUDIO/VIDEO input
jack.
System
Used in
PAL
Australia, Austria, Belgium,
China, Czech Republic,
Denmark, Finland, Germany,
Holland, Hong Kong, Hungary,
Italy, Kuwait, Malaysia, New
Zealand, Norway, Poland,
Portugal, Singapore, Slovak
Republic, Spain, Sweden,
Switzerland, Thailand, United
Kingdom, etc.
PAL-M
PAL-N
NTSC
Brazil
Argentina, Paraguay, Uruguay
Bahama Islands, Bolivia,
Canada, Central America,
Chile, Colombia, Ecuador,
Guyana, Jamaica, Japan,
Korea, Mexico, Peru, Surinam,
Taiwan, the Philippines, the
USA, Venezuela, etc.
SECAM
Bulgaria, France, Guiana, Iran,
Iraq, Monaco, Russia, Ukraine,
etc.
9ꢄ
Setting to the local time
You can easily set the clock to the local time by setting a time difference when using your
camcorder abroad. Touch (HOME)
(SETTINGS) [CLOCK/ LANG]
[AREA SET] and [SUMMERTIME] (p. 75).
World time difference
Time-zone
differences
Area setting
Time-zone
differences
Area setting
–09:00
–08:00
–07:00
–06:00
–05:00
–04:00
–03:30
–03:00
–02:00
–01:00
Alaska
GMT
Lisbon, London
Berlin, Paris
Helsinki, Cairo, Istanbul
Moscow, Nairobi
Tehran
Abu Dhabi, Baku
Kabul
Karachi, Islamabad
Calcutta, New Delhi
Almaty, Dhaka
Yangon
Los Angeles, Tijuana
Denver, Arizona
Chicago, Mexico City
New York, Bogota
Santiago
+01:00
+02:00
+03:00
+03:30
+04:00
+04:30
+05:00
+05:30
+06:00
+06:30
+07:00
+08:00
St.John’s
Brasilia, Montevideo
Fernando de Noronha
Azores, Cape Verde Is.
Bangkok, Jakarta
Hong Kong, Singapore,
Beijing
+09:00
+09:30
+10:00
+11:00
+12:00
Seoul, Tokyo
Adelaide, Darwin
Melbourne, Sydney
Solomon Is
Fiji, Wellington, Eniwetok,
Kwajalein
–11:00
–10:00
Samoa
Hawaii
97
File/folder structure on the internal hard disk and
“Memory Stick PRO Duo”media
The file/folder structure is shown below. You do not usually need to acknowledge the file/
folder structure, when recording/playing back movies and photos on the camcorder. To enjoy
movies or photos by connecting your camcorder to a computer, see “PMB Guide” then use the
supplied application.
* Only for the internal hard disk
The folder name goes up: [101MSDCF]
Image management files
[102MSDCF]
When you delete the files, you cannot
record/play back the images correctly.
The files are defaulted as hidden files
and not usually displayed.
By setting
(HOME) (OTHERS)
[USB CONNECT] [ USB CONNECT]/
[
USB CONNECT], you can access the
recording media from the computer through
USB connection.
Movie files (MPEG2 files)
Access from the computer using the supplied
software “PMB.” Do not modify the files
or folders on the camcorder through the
computer without using the supplied computer
application. The image files may be destroyed
or may not be played back.
The extension of the files is “.MPG”.
The maximum size is 2 GB. When the
capacity of a file exceeds 2 GB, the file
becomes divided.
The file numbers go up automatically.
When the capacity of a file number
exceeds 9999, another folder is created
to record new movie files.
Operation is not guaranteed, if you perform the
above operation.
When you delete image files, follow the steps
camcorder directly from the computer.
Do not format the recording media using a
computer. The camcorder may not operate
correctly.
Do not copy the files on the recording
media from the computer. Operation is not
guaranteed.
The folder name goes up: [101PNV01]
[102PNV01]
Photo files (JPEG files)
The extension of the files is “.JPG”. The
file numbers go up automatically. When
the capacity of a file number exceeds
9999, another folder is created to store
new photo files.
You cannot import data on the media
of the camcorder from the computer
(DCR-SR37E/SR38E/SR57E/SR77E).
98
camcorder is reading or writing image files on
the “Memory Stick PRO Duo” media (while
the ACCESS/access lamp is lit or flashing)
If you use the “Memory Stick PRO Duo”
media near magnets or magnetic fields
It is recommended that you make a back-up of
important data on the hard disk of a computer.
Be careful not to apply excessive force when
writing a memo area on “Memory Stick PRO
Duo” media.
Do not attach a label or the like on “Memory
Stick PRO Duo” media or “Memory Stick Duo”
media adaptor.
When you carry or store “Memory Stick PRO
Duo” media, put it in its case.
Maintenance and
precautions
About the “Memory Stick”media
“Memory Stick” media are a compact,
portable IC recording medium with a large
data capacity.
You can use only “Memory Stick Duo”
media, which are about the half size of
standard “Memory Stick” media, with your
camcorder.
However, we do not guarantee the
operation of all types of “Memory Stick
Duo” media on your camcorder.
Do not touch, or allow metallic objects to come
into contact with the terminals.
Do not bend, drop or apply strong force to the
“Memory Stick PRO Duo” media.
Do not disassemble or modify the “Memory
Stick PRO Duo” media.
Do not let the “Memory Stick PRO Duo” media
get wet.
Keep the “Memory Stick PRO Duo” media out
of the reach of small children. There is danger
that a child might swallow it.
Do not insert anything other than “Memory
Stick PRO Duo” media into the “Memory
Stick Duo” media slot. Doing so may cause a
malfunction.
Do not use or keep the “Memory Stick PRO
Duo” media in the following locations:
Places subject to extremely high temperature,
such as a car parked outside in the summer
Places under direct sunlight
Places with extremely high humidity or
subject to corrosive gases
Types of“Memory Stick”media
Recording/Playback
“Memory Stick Duo”
media (with MagicGate)
—
“Memory Stick PRO
Duo” media
“Memory Stick PRO-HG
Duo” media
*
* This product does not support 8-bit parallel
data transfer but it supports 4-bit parallel data
transfer the same as with “Memory Stick PRO
Duo” media.
This product cannot record or play data that
uses “MagicGate” technology. “MagicGate” is
a copyright protection technology that records
and transfers the contents in an encrypted
format.
This product is compatible with “Memory Stick
Micro” media (“M2”). “M2” is the abbreviation
for the “Memory Stick Micro” media.
“Memory Stick PRO Duo” media formatted by a
computer (Windows OS/Mac OS) does not have
guaranteed compatibility with your camcorder.
Data read/write speed may vary depending on
the combination of the “Memory Stick PRO
Duo” media and “Memory Stick PRO Duo”
media compliant product you use.
On the “Memory Stick Duo”media
adaptor
When using “Memory Stick PRO Duo” media
with “Memory Stick” media compliant device,
be sure to insert the “Memory Stick PRO Duo”
media into “Memory Stick Duo” media adaptor.
When using “Memory Stick PRO Duo” media
with “Memory Stick” media compliant device
inserting “Memory Stick PRO Duo” media
into “Memory Stick Duo” media adaptor, make
sure the “Memory Stick PRO Duo” media are
inserted facing in the correct direction. Note
that improper use may cause a malfunction.
Damaged or lost data may occur in the
following cases (the data will not be
compensated for):
If you eject the “Memory Stick PRO Duo”
media, or turn off your camcorder while your
99
When using “Memory Stick PRO Duo” media
inserted into “Memory Stick Duo” media
adaptor on “Memory Stick” media compliant
device, make sure the “Memory Stick PRO
Duo” media adaptor is inserted into the device
in the correct direction. If inserted in the wrong
direction, the device may be damaged.
Do not insert “Memory Stick Duo” media
adaptor without “Memory Stick PRO Duo”
media attached into “Memory Stick” media
compliant device. Doing so may result in
malfunctions of the device.
your camcorder:
When playing back image data modified on
your computer
When playing back image data recorded with
other devices
About the “InfoLITHIUM”battery
pack
Your camcorder operates only with an
“InfoLITHIUM” battery pack (H series).
“InfoLITHIUM” H series battery packs
On “Memory Stick PRO Duo”media
have the
mark.
The maximum memory capacity of “Memory
Stick PRO Duo” media that can be used with
your camcorder is 16 GB.
What is an “InfoLITHIUM”battery pack?
An “InfoLITHIUM” battery pack is a
lithium-ion battery pack that has functions
for communicating information related to
operating conditions between your camcorder
and an AC Adaptor/charger (sold separately).
The “InfoLITHIUM” battery pack calculates the
power consumption according to the operating
conditions of your camcorder, and displays the
remaining battery time in minutes.
The battery pack NP-FH50 supplied with
DCR-SR77E/SR87E is compatible with
“ActiFORCE.” “ActiFORCE” is a new generation
power system. Battery capacity, boost charge,
and the speed and accuracy of battery time
remaining calculations have been improved
when compared with current “InfoLITHIUM”
P-series batteries.
Notes on using “Memory Stick Micro”
media
To use “Memory Stick Micro” media with your
camcorder, you need a Duo-sized M2 Adaptor.
Insert the “Memory Stick Micro” media into
the Duo-sized M2 Adaptor, and then insert the
adaptor into the “Memory Stick Duo” media
slot. If you insert a “Memory Stick Micro”
media into your camcorder without using a
Duo-sized M2 Adaptor, you might not be able
to remove it from your camcorder.
Do not leave the “Memory Stick Micro” media
within the reach of small children. They might
accidentally swallow it.
On image data compatibility
To charge the battery pack
Be sure to charge the battery pack before you
start using your camcorder.
We recommend charging the battery pack in an
ambient temperature of between 10 C to 30 C
(50 ˚F to 86 ˚F) until the CHG (charge) lamp
turns off. If you charge the battery pack outside
of this temperature range, you may not be able
to charge it efficiently.
Image data files recorded on “Memory Stick
PRO Duo” media by your camcorder conform
to the “Design rule for Camera File system”
universal standard established by the JEITA
(Japan Electronics and Information Technology
Industries Association).
On your camcorder, you cannot play back
photos recorded on other devices (DCR-
TRV900E or DSC-D700/D770) that do not
conform to the universal standard. (These
models are not sold in some regions.)
To use the battery pack effectively
Battery pack performance decreases when the
ambient temperature is 10 C (50 °F) or below,
and the length of time you can use the battery
pack becomes shorter. In that case, do one
of the following to use the battery pack for a
longer time.
If you cannot use “Memory Stick PRO Duo”
media that have been used with another device,
that formatting erases all information on the
“Memory Stick PRO Duo” media.
You may not be able to play back images with
100
Put the battery pack in a pocket to warm it
up, and install it on your camcorder right
before you start taking shots.
Use a large capacity battery pack: NP-FH70/
FH100 (sold separately).
Frequent use of the LCD screen or a frequent
playback, fast forward or reverse operation
wears out the battery pack faster. We
About battery life
Battery capacity decreases over time and
through repeated use. If decreased usage time
between charges becomes significant, it is
probably time to replace it with a new one.
Each battery’s life is governed by storage,
operating and environmental conditions.
recommend using a large capacity battery pack:
NP-FH70/FH100 (sold separately).
Be sure to close the LCD screen when not
recording or playing back on your camcorder.
The battery pack is also consumed when your
camcorder is in recording standby or playback
pause.
Have spare battery packs ready for 2 or 3 times
the expected recording time, and make trial
recordings before making the actual recording.
Do not expose the battery pack to water. The
battery pack is not water resistant.
About handling of your camcorder
On use and care
Do not use or store the camcorder and
accessories in the following locations:
Anywhere extremely hot, cold or humid.
Never leave them exposed to temperatures
above 60 C (140 °F), such as under direct
sunlight, near heaters or in a car parked in
the sun. They may malfunction or become
deformed.
Near strong magnetic fields or mechanical
vibration. The camcorder may malfunction.
Near strong radio waves or radiation. The
camcorder may not be able to record properly.
Near AM receivers and video equipment.
Noise may occur.
About the remaining battery time
indicator
When the power goes off even though the
remaining battery time indicator indicates that
the battery pack has enough power to operate,
charge the battery pack fully again. Remaining
battery time will be indicated correctly. Note,
however, that the battery indication will not be
restored if it is used in high temperatures for
a long time, or if left in a fully charged state,
or when the battery pack is frequently used.
Use the remaining battery time indication as a
rough guide only.
On a sandy beach or anywhere dusty. If
sand or dust gets in your camcorder, it may
malfunction. Sometimes this malfunction
cannot be repaired.
Near windows or outdoors, where the LCD
screen, or the lens may be exposed to direct
sunlight. This damages the LCD screen.
Operate your camcorder on DC 6.8 V/7.2 V
(battery pack) or DC 8.4 V (AC Adaptor).
For DC or AC operation, use the accessories
recommended in these operating instructions.
Do not let your camcorder get wet, for example,
from rain or sea water. If your camcorder
gets wet, it may malfunction. Sometimes this
malfunction cannot be repaired.
If any solid object or liquid gets inside the
casing, unplug your camcorder and have it
checked by a Sony dealer before operating it
any further.
Avoid rough handling, disassembling,
modifying, physical shock, or impact such
as hammering, dropping or stepping on the
product. Be particularly careful of the lens.
Keep the LCD screen closed when you are not
using your camcorder.
The mark that indicates low battery flashes
even if there are still 20 minutes of battery
time remaining, depending on the operating
conditions or ambient temperature.
About storage of the battery pack
If the battery pack is not used for a long time,
fully charge the battery pack and use it up on
your camcorder once a year to maintain proper
function. To store the battery pack, remove it from
your camcorder and put it in a dry, cool place.
To discharge the battery pack on your
camcorder completely, touch
(HOME)
(SETTINGS) [GENERAL SET]
[A.SHUT OFF] [NEVER], and leave your
camcorder in recording standby until the power
goes off (p. 76).
101
Do not wrap your camcorder with a towel, for
example, and operate it. Doing so might cause
heat to build up inside.
When disconnecting the power cord (mains
lead), pull it by the plug and not the cord.
Do not damage the power cord (mains lead)
such as by placing anything heavy on it.
Do not use a deformed or damaged battery
pack.
How to prevent moisture condensation
When you bring your camcorder from a cold
place into a warm place, put your camcorder in
a plastic bag and seal it tightly. Remove the bag
when the air temperature inside the plastic bag
has reached the surrounding temperature (after
about 1 hour).
LCD screen
Keep metal contacts clean.
Do not exert excessive pressure on the LCD
screen, as it may cause uneven color and other
damage.
If your camcorder is used in a cold place, a
residual image may appear on the LCD screen.
This is not a malfunction.
If the battery electrolytic liquid has leaked:
Consult your local authorized Sony service
facility.
Wash off any liquid that may have contacted
your skin.
If any liquid gets in your eyes, wash with
plenty of water and consult a doctor.
While using your camcorder, the back of
the LCD screen may heat up. This is not a
malfunction.
When not using your camcorder for a
long time
To clean the LCD screen
If fingerprints or dust make the LCD screen
dirty, it is recommended that you use a soft
cloth to clean it.
When you use the LCD Cleaning Kit (sold
separately), do not apply the cleaning liquid
directly to the LCD screen. Use cleaning paper
moistened with the liquid.
To keep your camcorder in optimum state for a
long time, turn it on and let it run by recording
and playing back images about once a month.
Use up the battery pack completely before
storing it.
Moisture condensation
If your camcorder is brought directly from a cold
place to a warm place, moisture may condense
inside your camcorder. This may cause a
malfunction to your camcorder.
If moisture condensation has occurred
Leave your camcorder for about 1 hour without
turning it on.
Note on moisture condensation
Moisture may condense when you bring your
camcorder from a cold place into a warm place
(or vice versa) or when you use your camcorder
in a humid place as follows:
On adjustment of the touch panel
(CALIBRATION)
The buttons on the touch panel may not work
correctly. If this happens, follow the procedure
below. It is recommended that you connect your
camcorder to the wall outlet (wall socket) using
the supplied AC Adaptor during the operation.
Touch
(HOME)
(SETTINGS)
[GENERAL SET] [CALIBRATION].
You bring your camcorder from a ski slope
into a place warmed up by a heating device.
You bring your camcorder from an air
conditioned car or room into a hot place
outside.
You use your camcorder after a squall or a
shower.
You use your camcorder in a hot and humid
place.
Touch “” displayed on the screen with the
corner of “Memory Stick PRO Duo” media or
the like 3 times.
Touch [CANCEL] to cancel calibration.
10ꢀ
will not be affected as long as you are not
recording the date.
Notes
If you did not press the right spot, try the
calibration again.
Do not use a sharp-pointed object for
calibration. Doing so may damage the LCD
screen.
You cannot calibrate the LCD screen if it is
rotated, or closed with the screen facing out.
How to charge the pre-installed
rechargeable battery
Connect your camcorder to a wall outlet (wall
socket) using the supplied AC Adaptor, and leave
it with the LCD screen closed for more than 24
hours.
On handling the casing
Note on disposal/transfer of the
“Memory Stick PRO Duo”media
If the casing is soiled, clean the camcorder body
with a soft cloth lightly moistened with water,
and then wipe the casing with a dry soft cloth.
Avoid the following to avoid damage to the
finish:
Using chemicals such as thinner, benzine,
alcohol, chemical cloths, repellent, insecticide
and sunscreen
Handling the camcorder with above
substances on your hands
Leaving the casing in contact with rubber or
vinyl objects for a long period of time
Even if you delete data in the “Memory Stick PRO
Duo” media or format the “Memory Stick PRO
Duo” media on your camcorder or a computer,
you may not delete data from the “Memory Stick
PRO Duo” media completely. When you give the
“Memory Stick PRO Duo” media to somebody, it
is recommended that you delete date completely
using data deletion software on a computer. Also,
when you dispose of the “Memory Stick PRO
Duo” media, it is recommended that you destroy
the actual body of the “Memory Stick PRO Duo”
media.
About care and storage of the lens
Wipe the surface of the lens clean with a soft
cloth in the following instances:
When there are fingerprints on the lens
surface
In hot or humid locations
When the lens is exposed to salty air such as
at the seaside
Store in a well-ventilated location subject to
little dirt or dust.
To prevent mold, periodically clean the lens as
described above.
On charging the pre-installed
rechargeable battery
Your camcorder has a pre-installed rechargeable
battery to retain the date, time, and other settings
even when the LCD screen is closed. The pre-
installed rechargeable battery is always charged
while your camcorder is connected to the wall
outlet (wall socket) via the AC Adaptor or while
the battery pack is attached. The rechargeable
battery will be fully discharged in about 3 months
if you do not use your camcorder at all. Use
your camcorder after charging the pre-installed
rechargeable battery.
However, even if the pre-installed rechargeable
battery is not charged, the camcorder operation
10ꢁ
On trademarks
“Handycam” and
Notes on the License
are
ANY USE OF THIS PRODUCT OTHER
THAN CONSUMER PERSONAL USE IN ANY
MANNER THAT COMPLIES WITH THE
MPEG-2 STANDARD FOR ENCODING VIDEO
INFORMATION FOR PACKAGED MEDIA
IS EXPRESSLY PROHIBITED WITHOUT A
LICENSE UNDER APPLICABLE PATENTS IN
THE MPEG-2 PATENT PORTFOLIO, WHICH
LICENSE IS AVAILABLE FROM MPEG LA,
L.L.C., 250 STEELE STREET, SUITE 300,
DENVER, COLORADO 80206.
registered trademarks of Sony Corporation.
“Memory Stick,” “
,” “Memory Stick Duo,”
,” “Memory Stick PRO
,” “Memory
“
Duo,” “
Stick PRO-HG Duo,” “
,” “Memory Stick Micro,” “MagicGate,” “
,” “MagicGate Memory
Stick” and “MagicGate Memory Stick Duo” are
trademarks or registered trademarks of Sony
Corporation.
“InfoLITHIUM” is a trademark of Sony
Corporation.
“DVDirect” is a trademark of Sony
Corporation.
Dolby and the double-D symbol are trademarks
of Dolby Laboratories.
Microsoft, Windows, Windows Media,
Windows Vista, and DirectX are either
registered trademarks or trademarks of
Microsoft Corporation in the United States and/
or other countries.
“C Library,” “Expat,” “zlib,” and “libjpeg” software
are provided in your camcorder. We provide
this software based on license agreements with
their owners of copyright. Based on requests
by the owners of copyright of these software
applications, we have an obligation to inform
you of the following. Please read the following
sections.
Read “license1.pdf” in the “License” folder on the
CD-ROM. You will find licenses (in English) of
“C Library,” “Expat,” “zlib,” and “libjpeg” software.
Macintosh and Mac OS are registered
trademarks of Apple Inc. in the U.S. and other
countries.
Intel, Intel Core, and Pentium are trademarks
or registered trademarks of Intel Corporation
or its subsidiaries in the United States and other
countries.
Adobe, the Adobe logo, and Adobe Acrobat
are either registered trademarks or trademarks
of Adobe Systems Incorporated in the United
States and/or other countries.
On GNU GPL/LGPL applied software
The software that is eligible for the following
GNU General Public License (hereinafter referred
to as “GPL”) or GNU Lesser General Public
License (hereinafter referred to as “LGPL”) are
included in the camcorder.
This informs you that you have a right to have
access to, modify, and redistribute source code for
these software programs under the conditions of
the supplied GPL/LGPL.
Source code is provided on the web. Use
the following URL to download it. When
downloading the source code, select DCR-SR87 as
the model for your camcorder.
All other product names mentioned herein may
be the trademarks or registered trademarks of
their respective companies. Furthermore,
and are not mentioned in each case in this
Handbook.
http://www.sony.net/Products/Linux/
We would prefer you do not contact us about the
contents of source code.
Read “license2.pdf” in the “License” folder on the
CD-ROM. You will find licenses (in English) of
“GPL,” and “LGPL” software.
To view the PDF, Adobe Reader is needed. If
it is not installed on your computer, you can
download it from the Adobe Systems web page:
http://www.adobe.com/
10ꢂ
Index
Disc recorder...............................56
DISP OUTPUT...........................74
DIVIDE........................................50
DROP SENSOR ..........................77
DVD writer..................................55
Symbols
L
16:9 .........................................43, 65
4:3 ...........................................43, 65
5.1ch surround recording..........33
LANDSCAPE..............................81
LCD BL LEVEL ..........................72
LCD BRIGHT .............................72
LCD COLOR...............................73
LP..................................................64
A
A.SHUT OFF ..............................76
A/V connecting cable.................56
Abroad .........................................96
Altitude ........................................14
AUDIO MODE...........................64
AUTO SLW SHUTTR .........66, 69
E
Easy Handycam Operation .......22
EDIT.............................................50
M
Maintenance................................99
MEDIA INFO .............................61
“Memory Stick” media.........59, 99
“Memory Stick PRO-HG Duo”
media......................................60, 99
“Memory Stick PRO Duo” media
.......................................... 59, 60, 98
Menus...........................................10
Mirror mode ...............................34
Moisture condensation ............102
MOVIE DUB ..............................47
MOVIE MEDIA SET .................59
Movies............................. 25, 28, 35
MOVIE SETTINGS ...................64
MPEG 2 .......................................98
F
Face Index....................................38
FILE NO.......................................68
Film Roll Index ...........................38
FIREWORKS ..............................81
FOCUS.........................................80
Folder ...........................................98
Format..........................................62
B
BATTERY INFO.........................58
Battery pack.................................16
BEACH ........................................81
BEEP.............................................72
BLACK FADER ..........................83
BLT-IN ZOOM MIC..................83
C
CAMERA DATA ........................70
CANDLE .....................................81
Capturing a photo from
a movie.........................................46
G
GENERAL SET...........................76
GUIDEFRAME.....................66, 69
Charging the battery pack
abroad ....................................17, 96
CLOCK/LANG...........................75
CLOCK SET..........................19, 75
Creating a disc ............................53
N
H
Notes on using the Hard Disk
Drive Handycam.........................14
HELP function............................10
High altitude ...............................14
HOME MENU......................10, 11
O
ONE PUSH .................................82
OPTION MENU ........... 10, 12, 78
original.........................................47
OTHERS......................................44
OUTDOOR.................................82
I
D
Image management file..............98
INDOOR .....................................82
“InfoLITHIUM” battery pack
.....................................................100
DATA CODE ..............................70
DATE/TIME..........................19, 70
Date Index ...................................39
DELETE.......................................44
DIGITAL ZOOM .......................65
DISC BURN ................................11
P
Internal hard disk .......................98
PB zoom.......................................40
J
10ꢃ
PHOTO COPY ...........................48
PHOTO MEDIA SET ................59
Photos ............................. 26, 30, 36
PHOTO SETTINGS...................68
Playing....................................25, 35
Playlist..........................................51
PMB Guide....................................2
PORTRAIT..................................81
PROTECT ...................................49
SUMMERTIME..........................75
SUNRISE&SUNSET...................81
Supplied items.............................13
T
TELE MACRO............................79
Tripod.............................................7
Troubleshooting..........................85
TV.................................................42
R
U
REC MODE.................................64
Recording ....................................28
Recording and playback time ...93
Recording media.........................59
USB cable.....................................55
USB CONNECT.........................55
V
Recording time of movies/
VBR ..............................................94
VISUAL INDEX ...................25, 35
number of recordable photos....93
REMAINING SET......................67
Repair...........................................85
W
S
WHITE BAL. ..............................82
WHITE FADER..........................83
Wide angle...................................32
SCENE SELECTION .................81
Screen indicators ..........................8
Self-diagnosis display/Warning
SELF-TIMER...............................84
Shooting.......................................30
SNOW..........................................81
SOUND/DISP SET.....................72
SPORTS .......................................81
SPOT FOCUS .............................79
SPOT METER.............................78
STEADYSHOT ...........................66
Z
Zoom......................................32, 40
10ꢄ
Additional information on this product and
answers to frequently asked questions can
be found at our Customer Support Website.
http://www.sony.net/
107
|