Sony CDC X317 User Manual

OPERATING INSTRUCTIONS  
MANUAL DE INSTRUCCIONES  
MODE D’EMPLOI  
CDC-X517M  
YU  
CDC-X417  
YU  
CDC-X317  
YU  
STEREO CAR CD RECEIVER  
RADIO-TOCADISCOS DE CD ESTEREOFONICO PARA  
AUTOMOVIL  
ENGLISH  
ESPAÑOL  
FRANÇAIS  
OWNER’S RECORD  
For your convenience, record the model number and  
serial number (you will find them on the bottom side of  
your set) in the space provided below. Please refer to  
them when you contact your AIWA dealer in case of  
difficulty.  
Model No. CDC-X517M, CDC-X417, CDC-X317  
Serial No.  
THEFT PROTECTION  
BASIC OPERATION,  
AUDIO AND CLOCK  
ADJUSTMENT  
Take the front panel with you when leaving the car, and  
keep it in the supplied carrying case.  
Detaching the front panel  
Before detaching the front panel, remove the CD to  
prevent possible damage to the unit.  
1
2
3
Press z to remove the CD.  
Press and hold PWR/MUTE until the unit turns off.  
Press %. (Hold the panel with one hand to prevent  
accidentally dropping it.)  
4
Remove the panel.  
Smart Jog  
Turning the unit on/off  
• Press PWR/MUTE to turn on the unit. The unit also  
turns on when you insert a CD.  
• Press and hold PWR/MUTE until the unit turns off.  
Note  
Most operations described in this manual require the  
unittobeturnedonbeforestartingtheoperation, unless  
explicitly stated otherwise.  
Attaching the front panel  
1
2
Engagetheleftsideofthefrontpaneltotheleftcatch  
on the unit.  
Changing the source mode  
Push the panel forward until it locks. Be sure not to  
press any buttons while you are attaching the panel.  
1
Press FNC.  
Pressing FNC cycles through source modes in the  
following order:  
* “CD” does not appear in the display when there is no  
CD in the unit.  
**CD Changer Play mode (CDC-X517M only, available  
when an optional CD Changer is connected)  
Adjusting the volume  
Note  
Donottouchthefrontpanelconnector.Thiscouldcause  
a poor or faulty connection.  
1
Turn the Smart Jog.  
VOL (volume) indicator flashes.  
Security lamp  
Muting the sound  
The security lamp will continue to flash while the front  
panel is detached from the unit.  
1
Press PWR/MUTE briefly.  
To restore volume, briefly press PWR/MUTE again.  
ENGLISH 2  
Adjusting sound  
Setting the clock  
You can select the following modes for adjusting sound  
depending on the music you listen to: BASS (low  
frequencies), TRE (high frequencies), BAL (left/right),  
FAD (front/ rear) and H-BASS (high bass)  
1
2
3
Press and holdDISP until the clock indicator flashes  
in the display.  
Press TUNEi (to set hour) or TUNEk (to set  
minute) and turn the Smart Jog.  
Press DISP.  
1
Press SEL repeatedly to select the mode to be  
adjusted.  
Pressing SEL cycles through the modes. The  
selected mode’s indicator flashes.  
TurntheSmartJogtoincreaseordecreasethelevel  
for the selected mode (except for H-BASS).  
In H-BASS mode, turn the Smart Jog to select on or  
off.  
Displaying the clock  
1
Press DISP.  
2
To return to the former display, press DISP again.  
RADIO OPERATION  
Note  
Adjust the level or select on/off within 5 seconds, or the  
selected mode will return to previous state.  
Tuning in to a station  
(Seek/Manual Tuning)  
Aligning the source levels  
(Source Level Adjuster)  
Volume may vary each time you change the source  
mode. In this case, you can align each source mode’s  
volume to almost the same level.  
1
2
PressFNCrepeatedlytoselectthedesiredmode.  
Press DISP while pressing SEL.  
“LA 0” appears in the display.  
Stereo indicator Local indicator  
3
Turn the Smart Jog to adjust the level.  
Note  
Adjust the level within 5 seconds, or the selected mode  
will be canceled.  
Band indicator Frequency indication  
Restoring the factory settings  
1
Press FNC repeatedly to select the desired band  
(FM1, FM2, FM3, AM1 or AM2).  
1
2
Turn off the unit.  
Press and hold DISP until “LA --” appears in the  
display.  
2* Press TUNEi (to move to higher frequencies) or  
TUNEk (to move to lower frequencies) to tune in to  
a station.  
Note  
“ST” appears in the display when a station is  
broadcasting in stereo, and receiving conditions are  
good.  
YoucanrestorethefactorysettingsonlyforVOL,BASS,  
TRE, BAL, FAD, and H-BASS, and aligned source  
volume levels.  
*Seek Tuning and Manual Tuning  
• Press and hold TUNEi or TUNEk until seek Tuning  
starts.  
Muting button beep sounds  
The unit locates a station automatically (Seek Tuning).  
• Press TUNEi or TUNEk repeatedly to search for a  
desired station while increasing or decreasing the  
frequency step by step (Manual Tuning).  
To stop Seek Tuning, press TUNEi or TUNEk  
again.  
1
2
Turn off the unit.  
Press and hold SEL until “bEEP” appears in the  
display.  
3
4
Turn the Smart Jog to select on (level indicators  
appear) or off (level indicators disappear).  
Press and hold SEL until the unit turns off.  
Monaural mode  
When signals become weak, or reception becomes  
poor, the unit automatically switches to Monaural mode  
to reduce noise.  
3 ENGLISH  
Local mode  
Presetting stations manually  
(Manual Memory)  
Local mode allows you to tune in only to strong stations  
during Seek Tuning.  
1
2
3
Press FNC repeatedly to select the desired band  
(FM1, FM2, FM3, AM1 or AM2).  
Press TUNEi or TUNEk to tune in to a desired  
station (see “Tuning in to a station,” page 3).  
Press the desired preset station button until the unit  
beeps.  
1
Press LO before you start seek tuning.  
“LO” appears in the display.  
To return to Distant mode, press LO again.  
“LO” disappears and the unit tunes in to all receivable  
stations.  
Using preset stations  
Note  
A newly preset station replaces the station on the same  
band that was previously stored on that preset station  
button.  
Youmustpresetstationsbeforeyoucantuneinastation  
using preset station number buttons.  
Tuning in to a preset station  
1
2
Press FNC repeatedly to select the desired band  
(FM1, FM2, FM3, AM1 or AM2).  
Press the preset station button on which the desired  
station is stored.  
Preset station buttons 1 ~ 6  
Active tuning reception control (ATRC)  
The unit automatically suppresses FM noise caused by  
vehicle movement, and maintains sound quality.  
Using the timer  
(My Information)  
Preset station  
number  
You can schedule the radio to activate for daily radio  
programs. The unit automatically turns on and off in  
Radio mode at the scheduled times.  
Presetting stations automatically  
(Auto Memory)  
1
Press FNC repeatedly to select the desired band  
(FM1, FM2, FM3, AM1 or AM2).  
Press and hold PS/A.ME until automatic presetting  
starts.  
2
The unit automatically stores up to 6 stations for  
each band.  
After completion of automatic presetting, the unit  
tunes in to the station stored on preset station  
button 1.  
MY INFO indicator  
Smart Jog  
Tocancelautomaticpresetting,pressPS/A.MEagain.  
Setting the timer  
Checking the preset stations (Preset Scan)  
1
2
Turn off the unit.  
Press and hold INFO until “PO” flashes in the  
display.  
Press SEL.  
1
Press PS/A.ME briefly.  
Each preset station will be tuned in for 5 seconds in  
order.  
To cancel Preset Scan, press PS/A.ME again or any  
3
4
Set the time you wish the unit to turn on.  
preset station button.  
• Press TUNEi and turn the Smart Jog to set the hour.  
• Press TUNEk and turn the Smart Jog to set the  
minute.  
5
6
7
Press SEL.  
Press FNC to select the band.  
PressTUNEi,TUNEkorthedesiredpresetstation  
button to select the station.  
8
9
Press SEL.  
Set the time you wish the unit to turn off following the  
same procedure used in step 4.  
ENGLISH 4  
Labeled-side up  
10 Press and hold INFO until the unit turns off, and  
setting is completed.  
When the unit is on, “MY INFO” appears in the  
display indicating that the unit is standby for a timer.  
During the timer-activated tuning, “MY INFO”  
continues to flash.  
To cancel the timer standby, press INFO so that  
“MY INFO” disappears.  
CD indicator  
Track number  
Note  
• To discontinue the timer setting, press and hold PWR/  
MUTE until the unit turns off.  
• To check the setting, turn off the unit, then pressINFO.  
The unit displays the scheduled turn-on and turn-off  
times with the appropriate radio frequency.  
• The unit automatically starts tuning at the scheduled  
time regardless of the current source mode. When the  
scheduled program is over, the unit automatically  
returns to the former source mode.  
• Timer setting remains enabled even if you turn off the  
unit, and then turn it on. This is true even if you detach  
the front panel, and reattach it.  
Elapsed playing time  
To  
Press  
z
Eject a CD  
Skip to the next track  
t
r
Go back to the beginning  
of the current track  
Each extra press skips  
backward one extra track  
• However, ifyoupressFNCtochangethesourcemode  
during timer-activated tuning, the scheduled program  
is canceled.  
Locate a specific point in Press and hold r or  
a track  
t until you find the  
point.  
Note  
CD PLAYER OPERATION  
• When you play a CD that is already inserted, CD play  
starts at the point where it stopped the previous time.  
A newly inserted CD starts from the first track.  
• A CD-R or CD-RW may take some time to start playing  
back, but this is not a malfunction.  
Playing a CD  
You can play CDs, CD-Rs and CD-RWs using the  
procedure described below.  
• If a CD-R or CD-RW with no data or incompatible data  
is inserted, “E03” will appear in the display. The unit  
cannot play such discs.  
Intro Play  
You can locate a desired track by monitoring the first 10  
seconds of all the tracks on a CD.  
1
Press INT during CD play.  
“SCAN” appears in the display.  
2
Press INT again when the desired track is played.  
The unit returns to normal CD play.  
1
Insert a CD.  
“CD” appears in the display.  
CD play starts.  
If a CD is already inserted, press FNC repeatedly to  
select CD play mode.  
One track Repeat Play  
You can play a track repeatedly.  
1
Press REP1 during CD play.  
“REPEAT1” appears in the display.  
To cancel One track Repeat Play, press REP1 again.  
In normal play, when the last track finishes, the unit  
returns to the first track and continues to play.  
Random Play  
You can play all the tracks in random order.  
1
Press RNDM during CD play.  
“RANDOM” appears in the display.  
To cancel Random Play, press RNDM again.  
Note  
During Random Play, pressing r allows you to skip  
only to the beginning of the current track, not to the  
previous track.  
5 ENGLISH  
AUXILIARY EQUIPMENT  
STEERING WHEEL  
REMOTE CONTROL  
(CDC-X517M and CDC-X417)  
Listening to a cassette/MD/MP3 portable  
player or other equipment  
Youcanlistentoequipmentconnectedtotheunit. Refer  
to the operating instructions for the corresponding  
equipment for more detailed information.  
Remote control button  
Be sure to remove inserted CDs to prevent possible  
damage to the unit before connecting the equipment.  
1 VOLUME + button: To increase the volume.  
2 VOLUME - button: To decrease the volume.  
3 FUNCTION button: To select Radio, CD Play, CD  
Changer Play (CDC-X517M only) or AUX IN mode.  
AUX IN jack  
1
2
Connectacassette/MD/MP3portableplayerorother  
equipment via the unit’s AUX IN jack (3.5 mm).  
Press FNC repeatedly until “AUX” appears in the  
display.  
4 DISC/PRESET  
button:  
(CD) To skip back to the beginning of the current  
track. Each extra press skips backward one extra  
track.  
During AUX mode, the clock display appears.  
(Radio) To tune in to the next preset station, in  
descending order.  
(CD Changer: CDC-X517M only)  
Press and release to skip back to the beginning of  
the current track or the previous track.  
Press and hold to switch to the previous CD.  
5 DISC/PRESET button:  
OTHER FUNCTIONS  
(CD) To skip to the next track.  
(Radio) To tune in to the next preset station, in  
ascending order.  
(CD Changer: CDC-X517M only)  
Smart Jog  
Press and release to skip to the next track.  
Press and hold to switch to the next CD.  
Changing the key illumination color  
(CDC-X517M and CDC-X417)  
CD CHANGER  
OPERATION  
(CDC-X517M only)  
Youcanchooseblueorredasthekeyilluminationcolor.  
1
Press and hold FNC until “ILL” appears in the  
display.  
2
TurntheSmartJogtoselect1(forblue)or2(forred).  
Playing a CD  
YoucanplayCDsfromaconnectedAIWACDChanger.  
For detailed information on installing a CD Changer,  
refertotheInstallationandConnectionmanualsupplied  
with the CD Changer.  
ENGLISH 6  
CD Changer indicator  
Track number  
TROUBLESHOOTING  
Error code  
In the following cases the corresponding error code  
indication appears. Follow the suggestions below to  
solve such problems. If the error code indication does  
not disappear, consult an AIWA service center.  
CD number  
Press FNC repeatedly to display “CD-CH.”  
E01* The disc magazine is not properly inserted in the  
CD Changer. Reinsert the magazine. Refer to  
the instruction manual for the CD Changer.  
E02* No CDs are loaded in the disc magazine. Insert  
CDsproperly. Refertotheinstructionmanualfor  
the CD Changer.  
E03 Focuserror.CheckthattheCDisloadedproperly  
(right side up, etc.), and the CD contains valid  
data.  
E04* Problem with the CD Changer. Reset the unit by  
pressing the Reset button. If this does not solve  
the problem, consult an AIWA service center.  
* CDC-X517M only  
1
The CD Changer play starts.  
To  
Press  
Skip to the next track  
t
Skip back to the beginning of  
the current track or to the  
previous track  
r
Advance rapidly to locate a  
desired point  
and hold t, then  
release it at the  
desired point  
Reverse rapidly to locate a  
desired point  
and hold r, then  
release it at the  
desired point  
Reset button  
Start CD Changer play from DISCN  
the first track on the next disc  
IfaCDdoesnotoperateproperly, presstheresetbutton  
with a pointed object such as a pencil, etc. Note that all  
your settings will be erased if this button is pressed.  
Start CD Changer play from DISCM  
the first track on the previous  
disc  
Intro Play  
You can locate a desired track by monitoring the first 10  
secondsofallthetracksontheCDsinthediscmagazine.  
1
Press INT during CD Changer play.  
“SCAN” appears in the display.  
Reset button  
2
Press INT again when the desired track is played.  
The unit returns to normal CD play.  
One track Repeat Play  
You can play a track repeatedly.  
MAINTENANCE  
1
Press REP1 during CD Changer play.  
“REPEAT1” appears in the display.  
To cancel Repeat Play, press REP1 again.  
Cleaning the front panel  
Wipe the surface with a soft, dry cloth.  
One disc Repeat Play  
You can play all tracks on a disc repeatedly.  
Cleaning the connector  
1
Press REP during CD Changer play.  
The connector needs to be cleaned occasionally. Wipe  
the surface of the connector with a cotton swab slightly  
moistened with alcohol.  
“REPEAT” appears in the display.  
To cancel Repeat Play, press REP again.  
Random Play  
You can play all the tracks on the CDs in the disc  
magazine in random order.  
Back of the front panel  
1
Press RNDM during CD Changer play.  
“RANDOM” appears in the display.  
To cancel Random Play, press RNDM again.  
Note  
PressingrduringRandomPlaylocatesthebeginning  
of the current track. The unit does not retrieve previous  
tracks during Random Play.  
7 ENGLISH  
STEERING WHEEL REMOTE CONTROL  
SPECIFICATIONS  
RADIO SECTION  
(CDC-X517M and CDC-X417)  
Dimensions: approx. 67 (W) × 26 (H) × 27 (D) mm  
(2 3/4 (W) × 1 1/16 (H) × 1 1/8 (D) inches) (excluding  
holder)  
Weight: approx. 38 g (1.33 oz.) (including holder,  
battery)  
(FM)  
Frequency Range: 87.5 MHz – 108 MHz (100-kHz  
steps)* or 87.5 MHz – 108 MHz (50-kHz steps)*  
Usable Sensitivity: 12.7 dBf  
50 dB Quieting Sensitivity: 17.2 dBf  
IF Rejection: 80 dB  
Supplied Accessories: Mounting kit (1 set), Lithium  
battery (1)  
Frequency Response: 30 Hz – 15,000 Hz  
S/N Ratio: 63 dB  
Stereo Separation: 35 dB at 1 kHz  
Alternate Channel Selectivity: 70 dB  
Capture Ratio: 3 dB  
• Specifications and external appearance are subject to  
change without notice due to product improvement.  
REAR PANEL  
(AM)  
CDC-X517M  
Frequency Range: 530 kHz – 1,710 kHz (10-kHz  
steps)* or 531 kHz – 1,602 kHz (9-kHz steps)*  
Usable Sensitivity: 30 µV (30 dB)  
* Set the frequency increment for your area using  
the switch on the bottom of the unit. (The switch  
is factory-set to the 10k position [for the U.S.A.])  
CDC-X417, CDC-X317  
CD SECTION  
Frequency Response: 17 Hz – 20 kHz +0/–3 dB  
Dynamic Range: More than 80 dB  
Channel Separation: More than 65 dB  
S/N Ratio: More than 85 dB  
Wow/Flutter: Not applicable  
AUDIO SECTION  
Max. Power Output: 50 W × 4 channels  
(CDC-X517M), 45 W × 4 channels (CDC-X417,  
CDC-X317)  
AUX IN input  
Input sensitivity (load impedance) AUX IN: 300 mV  
(10 k)  
GENERAL  
Power-Supply Voltage: 14.4 V (11 to 16 V  
allowable), DC, negative ground  
Load Impedance: 4 Ω  
Tone Control:  
Bass ± 10 dB at 100 Hz, Treble ± 10 dB at 10 kHz  
Preamp Output Voltage (load impedance): 2.2 V  
(10 k)  
Installed size: 182 (W) × 53 (H) × 155 (D) mm  
(7 1/4 (W) × 2 1/8 (H) × 6 1/8 (D) inches)  
Supplied Accessory: Carrying case (1)  
ENGLISH 8  
8B-KCF-901-01  
000914ATM-OX  
Printed in Indonesia  

Yorkville Sound Car Speaker C130 User Manual
Toastmaster 1750 User Manual
Tektronix Camcorder 070 9960 01 User Manual
Soundstream Technologies RUB1.2500D User Manual
Sony XR C8220R User Manual
Sony Walkman WM FX495 User Manual
Sony VF 74CP User Manual
Sony TRV19 User Manual
Sony TC KB920S User Manual
Samsung Camcorder SCB 2000ND User Manual