Sirius Satellite Radio MSR4500 User Manual

MSR4500

Thank You!

¡Muchas gracias!

Thank you for choosing a JENSEN product. We hope you will find the instructions in this

owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn

how to use all the features of your new JENSEN / Sirius MSR4500 satellite radio for maximum

enjoyment.

Muchas gracias por escoger un producto JENSEN. Hemos hecho lo posible para que las

instrucciones en este manual sean claras y fáciles de seguir. Si se da unos pocos minutos para

leerlo, aprenderá a usar todos los elementos de su nuevo estéreo Jensen/Sirius para carros

para que pueda disfrutarlo al máximo.

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Instalación. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Operación . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Especificationes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Correción de problemas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Installation

Getting Started

It’s a good idea to read all of the instructions before you begin the installation.

System Components

The following components are required for complete operation of the satellite radio features.

•

MSR4500 head unit

Power cable (included)

Jensen/Sirius DLP2000 satellite receiver (purchased separately)

Sirius satellite antenna (purchased separately)

•

MSR4500 head unit

Power cable (included)

Jensen/Sirius DLP2000 satellite receiver (purchased separately)

Sirius satellite antenna (purchased separately)

Note: You will need to subscribe to Sirius Satellite Radio in order to use the

satellite features of this radio. After purchasing the required satellite receiver

(DLP2000) and Sirius Antenna, contact Sirius at 1-888-539-SIRIUS to subscribe.

Note: You will need to subscribe to Sirius Satellite Radio in order to use the

satellite features of this radio. After purchasing the required satellite receiver

(DLP2000) and Sirius Antenna, contact Sirius at 1-888-539-SIRIUS to subscribe.

MSR4500

Instalación (continuado)

Preparación (continuado)

Installation (continued)

Preparation (continued)

Import

Importe

Remove Old Radio (continued)

Cómo Desmontar la Radio Vieja (continuado)

Import

Importe

1. Remove dash panel to expose DIN chassis.

2. Remove screws that secure radio to the dashboard.

3. Disconnect wiring harness and remove radio.

4. Remove brackets from the side of radio.

Replacing an Aftermarket Radio

1. Bend tabs flat.

1. Quite el panel del tablero para exhibir los canales DIM.

2. Quite los tornillos quie aseguran el radio al tablero de instrumentos.

3. Desconecte el arnés del radio y quite el radio

4. Quite los soportes del lado del radio.

Reemplazo de la Radio Vieja

1. Doble las aletas hasta que están planas.

2. Hale la camisa del tablero de instrumentos. Quítela con cuidado.

2. Pull sleeve from dashboard.

Caution: Edges are sharp. Use a rag or wear a glove.

Cuidado: Los bordes son puntiagudos. Use un trapo o un guante.

Replacing an Aftermarket Radio

Reemplazo de la Radio Vieja

Install Half-Sleeve

Instalación de la Camisa

1. Install adapter if necessary.

2. Install half-sleeve into adapter or dashboard.

1. Instale el adaptador, si es necessario.

2. Instale la media camisa en el adaptador o en tablero de

instrumentos.

3. Push tabs out to secure half-sleeve in the radio

opening.

3. Hale las aletas hacia afuera para asegurar la media camisa en al

apertura del radio.

4. Install support strap to make unit more stable.

4. Instale la abrazadera de soporte para que la unidad quede más

estable.

Wiring

Wiring with a Wiring Adaptor

Cableado

1. Crimp or solder (refer to wiring color codes).

2. Attach wiring adaptor to wiring harness.

Conecte los Cables

1. Una o conecte a presión (vea los códigos de color del cableado).

2. Una el adaptador de cableado al arnés del cableado.

Wiring Color Codes

Códigos en Color de Cableado

Install Half-Sleeve

Connect Wires

Conecte los Cables

Instalación de la Camisa

MSR4500

Wiring Diagram

Diagrama de Cableado

MSR4500

Final Radio Installation

ISO-DIN Brackets

Instalacion Final de Radio

Soportes de ISO-DIN

Instalación (continuado)

Installation (continued)

Instalación Final

Final Installation

Radio

1. Conecte el adaptador del cableado al arnés existente del cableado.

1. Connect wiring adaptor to existing wiring harness.

2. Connect antenna lead, and make any appropriate connections for Sirius and Auxiliary Input.

3. Slide radio chasis into half-sleeve.

2. Donecte la cabeza de la antena, y haga cualquier conexión apropiada para Sirius y la

entrada auxiliar.

3. Deslice el chasis del radio en la media.

4. Secure Radio to bracket using nut (if possible).

5. Replace any items you removed from the dashboard.

4. Asegure el radio al soporte usando una tuerca (si es posible).

5. Ponga en su lugar cualquier artículo que haya quitado del tablero de instrumentos.

ISO-DIN Brackets

Soportes de ISO-DIN

1. Mount factory brackets on new radio.

2. Slide radio chassis into dash opening and secure.

3. Reinstall dash panel.

1. Instale los soported de fábrica en el radio nuevo.

2. Deslice el chasis del radio en la apertura del tablero y asegurelo.

3. Reinstale el panel del tablero.

Reconnect Battery

Reconexión de la Batería

When wiring is complete, reconnect the battery negative terminal.

Cuando haya terminado de colocar los cables, podrá hacer la reconexión de la batería a la

terminal negativa de la misma.

MSR4500

Basic Operation

Operación Básica

Audible Beep

Pitido Audible

Press AUD for three seconds to turn beep on or off. When beep is on, the Audible Beep symbol

Presione AUD por tres segundos para encender or apagar el pitido audible (beep). Cuando el

appears in the display.

pitido audible está encendido en el visualizador aparece el símbolo del pitido audible.

Mode

Modalidad

Press MODE to select from the following modes: Radio (TUNER), Satellite Radio (SIRIUS), CD

Player (CD Player), CD changer (CD Changer) or Auxilliary (AUX) . If a CD is not loaded, and/or

the satellite DLP or CD changer is not connected, these modes will be skipped.

Presione MODE para seleccionar la modalidad de Radio (TUNER), Radio Satélite (SIRIUS),

Reproductor de CD (CD Player), Tocador de CD (CD Changer) or Auxiliar (AUX). Los modos

serán exhibidos solamente si todas las conexiones necesarias se han hecho correctamente.

Power

Potencia

Press PWR or any other button to turn unit on. Press PWR to turn unit off.

Presione PWR o cualquier otro botón para encender la unidad. Presione PWR para apager la

unidad.

Loudness

Intensidad

Press LOUD to increase bass output. The “LOUD” icon appears in the display.

Presione LOUD para aumentar el tono del bajo. “LOUD” aparece en el visualizador cuando se lo

activa.

Mute

Silenciador

Press MUTE to silence the receiver. To restore sound, press MUTE again.

Presione MUTE para silenciar el receptor.

Volume

Volumen

Press VOL up (S) or down (T) to increase or decrease the volume.

Presione los botones de volumen (S o T) para aumentar o para disminuir el volumen.

Display Priority

Prioridad del Visualizador

Time Priority (TIME)

To select Time Priority, press and hold DISP while pressing the Down tuning button (<<).

Pressing DISP while in Time Priority will temporarily display selected station frequency (Radio

mode) or CD elapsed time (CD mode). To display the time again, press DISP momentarily.

Prioridad del Reloj (TIME)

Para seleccionar la Prioridad de Reloj, mantenga presionado DISP al tiempo que presiona el

botón <<. Si presiona DISP mientras se halla en Prioridad del Reloj, el visualizador indicará

temporalmente la frecuencia de la emisora seleccionada (en el modo de radio) o el tiempo

transcurrido del CD (en el modo CD).

Frequency Priority (FREQ)

To select Frequency Priority, press and hold DISP while pressing the Up tuning button (>>).

Pressing DISP while in Frequency Priority will temporarily display the time. To display the

frequency again, press DISP momentarily.

Prioridad de Frecuencia (FREQ)

Para seleccionar la Prioridad de Frecuencia, mantenga presionado DISP al tiempo que presiona

el botón >>. Si presiona DISP mientras se halla en Prioridad de Frecuencia, el visualizador

indicará temporalmente el reloj.

Set the Clock

1. Press and hold DISP for three seconds until clock display flashes, then release.

Cómo Poner en Funcionamiento el Reloj

2. Press the Down tuning button (<<) to change hours and the Up tuning button (>>) to change

minutes.

1. Presione y sostenga DISP por tres segundos hasta que el visualizador del reloj destelle.

Entonces suéltelo.

2. Pulse << para cambiar las horas y >> para cambiar los minutos.

MSR4500

Basic Operation

Operación Basica

Power

Potencia

Mode

Audible Beep

Pitido Audible

Modalidad

Mute

Silenciador

Display Priority

Volume

Prioridad del Visualizador

Volumen

Loudness

Intensidad

Operación Básica (continuado)

Sonidos Graves

Basic Operation (continued)

Bass

Adjust Sound

Ajuste Sonido

1. Presione AUD hasta que en el visualizador aparezca “BASS”.

1. Momentarily press AUD until “BASS” appears in the display.

2. Pulse los botones de volumen para regular los Bajos hacia

arriba o hacia abajo de -6 a +6.

2. Press the volume buttons to adjust Bass up or down from -6

to +6.

Sonidos Aguidos

Treble

1. Presione AUD hasta que en el visualizador aparezca “TREB”.

1. Momentarily press AUD until “TREB” appears in the display.

2. Pulse los botones de volumen para regular los Agudos hacia

arriba o hacia abajo de -6 a +6.

2. Press the volume buttons to adjust Treble up or down from -6

to +6.

Balance

1. Presione AUD hasta que en el visualizador aparezca “BAL”.

1. Momentarily press AUD until “BAL” appears in the display.

2. Pulse los botones de volumen para regular el Balance

Acústico a la izquierda o a la derecha de L12 a R12.

2. Press volume buttons to adjust Balance left or right from L12

to R12.

Atenuación Acústica

Fader

1. Presione AUD hasta que en el visualizador aparezca “FAD”.

1. Momentarily press AUD until “FAD” appears in the display.

2. Pulse los botones de volumen para regular el Atenuador

hacia adelante o hacia atrás de L12 a R12.

2. Press volume buttons to adjust Fader front or rear from F12

to R12.

MSR4500

Operación Básica (continuado)

Basic Operation (continued)

Removing the Faceplace

Retire la Placa Frontal

Placa Frontal Desmontable y Reversible

Puede retire la placa frontal terminando estos pasos:

1. Presione OPEN, y la placa frontal se abrirá hacia abajo.

Flip-Down Detachable Faceplace

The flip-down faceplace can be detached by following these

steps:

1. Press OPEN, and the faceplate will flip down.

2. Retire el tornillo que asegura. (El tornillo que aegura

puede ser reinstalado si la placa frontal desmontable no

se desea.)

2. Remove the locking screw (if used). (The locking screw

can be reinstalled if detachable faceplate is not desired.)

3. Levante y hale la placa frontal.

3. Lift and pull from the center to remove faceplate.

Para volver a instalar, deslice el extremo inferior en la radio,

levante la placa frontal y presiónela en su lugar.

To reinstall, slip bottom edge into radio, flip faceplate up, and

press into place.

Reset Button

El Botón Reset

Botón de Reset

Reset Button

Cuando la unidad no está respondiendo (hay mensaje del

anerror en la exhibición, o los controles se traban para

arriba), presione RESET para recomenzar el sistema.

When the unit is not responding (error message on display,

controls locked up, etc.), press RESET to restart the system.

1. Remove faceplate.

1. Quite la placa frontal.

2. Use a pencil (or other non-metallic object) to press

2. Use la punta de un lápiz (u otro objeto no metálico) para

RESET.

pulsar RESET.

Remove Radio from Dash

Extracción del Radio del Aotomóvil

Remove Radio from Dash

Extracción del Radio del Automóvil

In case of abnormal operation, you may need to remove the

radio from the dash.

En caso de mal functionamiento, pueda necesitar quitar la

radio del automóvil.

1. Remove faceplate.

1. Quite la placa frontal.

2. Remove trim ring by gently pulling up on the middle of

the trimming to release the plastic snaps.

2. Quite el anillo ornamental halando suavemente hacia

arriba desde el centro de la guarnición para aflojar los

broches plásticos de presión.

3. Insert removal keys between radio and dash to depress

locking springs. Pull radio out of dash.

3. Inserte las llaves de retiro entre la radio a la gurnaición

del tablero de instrumentos para oprimir los resortes de

seguridad. Saque la radio del tablero de instrumentos.

MSR4500

Radio Operation

Operación de la Radio

Seek Tuning

Syntonización por Búsqueda

Press the up or down tuning buttons (>> or <<) for less than one second to seek the next strong

Presione<< ó >> por menos de un segundo para buscar la siguiente emisora.

station in the current band.

Rastreo

Scan

Presione SCAN para rastrear las emisoras de señal fuerte de la banda actual. La radio hace pausa

por cinco segundos en cada emisora de señal fuerte. Presione de nuevo SCAN para escuchar la

emisora actual.

Press SCAN to scan through strong stations in the current band. The radio will pause for five

seconds at each station. Press SCAN again to stop scanning and listen to the current station.

Manual Tuning

Sintonización Manual

1. Press the up or down tuning buttons (>> or <<) for more than three seconds to select

1. Presione << ó >> por más de tres segundos para seleccionar el modo de sintonización manual.

manual tuning mode.

2. Presione << ó >> por menos de un segundo para mover el número de frecuencia del radio una

2. Press the up or down tuning buttons (>> or <<) for less than one second to move radio

parada hacia arriba o hacia abajo.

frequency up or down one step.

3. Presione y sostenga << ó >> para avanzar rápidamente a la frecuencia deseada.

3. Press and hold the up or down tuning buttons (>> or <<) to quickly advance to desired

Banda

frequency.

Presione BAND para sintonizar la radio entre las dos bandas FM y uno banda AM.

Band

Intervalo de Frecuencias

Press BAND to change between one AM and two FM bands.

El intervalo de frecuencias se puede fijar al estándar Americano o al estándar Europeo. Presione

simultáneamente BAND y << . El intervalo de frecuencias cambia al estándar Europeo. Presione

simultáneamente BAND y >>. El intervalo de frecuencias cambia al estándar Americano.

Frequency Spacing

Frequency spacing may be set to either the U.S. or European standard. Press BAND and <<

simultaneously. Release, and the frequency spacing will change to European standard. Press

BAND and >> simultaneously. Release, and the frequency spacing will change to U.S. standard.

Cómo Almacener una Emisora

Hasta 30 estaciones preestablecidas (10 en cada venda) se pueden almacenar.

Store and Recall a Station

1. Seleccione una emisora, y mantenga pulsado durante tres segundos un boton de preselección.

2. Pulse un botón de preselección para seleccionar una emisora almacenada previamente.

Up to 30 preset stations (10 on each band) can be stored for quick recall.

1. To store a station, select the station and hold the desired preset button for three seconds.

When stored, the preset number will appear in the display.

Almacenamiento Automático de Emisoras

2. To recall a station, press the corresponding preset button in the selected band.

Seleccione 10 emisoras de señal fuerte y almacénelas en la banda actual. Mantenga pulsado AS/

PS en forma por más de tres segundos. Los emisoras reemplazaran a aquellas que se habian

almacenado previamente.

Automatically Store Stations

Select 10 strong stations and store them in the current band using the Automatically Store

Stations feature. To enable this feature, hold AS/PS for more than three seconds. The new

stations replace stations already stored in that band.

Radio Operation

Operación de la Radio

Preselección Mediante Escáner

Preset Scan

Busque con el escáner las emisoras

almacenadas en la banda actual. Pulse AS/PS

por menos de tres segundos. La radio hará una

pausa de cinco segundos en cada emisora que

encuentre. Pulse AS/PS neuvamente para que

el escáner se detenga cuando haya encontrado

la emisora deseada.

Scan stations stored in the current band using

the Preset Scan feature. To enable Preset

Scan, press AS/PS for less than three seconds.

The radio will pause for five seconds at each

station. Press AS/PS again to stop scanning

and listen to the current station.

MSR4500

Satellite Operation

Acquiring Signal

When Satellite Mode is selected, “Sirius” will scroll across the first line of the display one time,

then “Acquiring Signal” will scroll. Once a signal is acquired, the letters “SAT”, along with the

satellite dish icon, will appear in the display.

When Satellite Mode is selected, “Sirius” will scroll across the first line of the display one time,

then “Acquiring Signal” will scroll. Once a signal is acquired, the letters “SAT”, along with the

satellite dish icon, will appear in the display.

If the user is not subscribed, “Call 888.539.SIRIUS To Subscribe” will appear in the display. The

phone number will scroll two times and stop. To scroll this text again, press FUNC for more than

three seconds.

If the user is not subscribed, “Call 888.539.SIRIUS To Subscribe” will appear in the display. The

phone number will scroll two times and stop. To scroll this text again, press FUNC for more than

three seconds.

Acquiring Text

After tuning channels, the radio will display either Channel Name/Song Title or Channel Name/

Artist Name. While waiting for text data, “Acquiring Text” will appear in the display.

After tuning channels, the radio will display either Channel Name/Song Title or Channel Name/

Artist Name. While waiting for text data, “Acquiring Text” will appear in the display.

Modes of Operation

Direct Mode

Direct mode allows a user to select individual channels or access channels directly. Direct mode

is the default mode for the unit.

Direct mode allows a user to select individual channels or access channels directly. Direct mode

is the default mode for the unit.

While in direct mode, the display will show Channel Number and either Channel Name/Song Title

or Channel Name/Artist Name. The Channel Name will always appear on the first line of the

display, and the Song Title or Artist Name will appear on the second line.

While in direct mode, the display will show Channel Number and either Channel Name/Song Title

or Channel Name/Artist Name. The Channel Name will always appear on the first line of the

display, and the Song Title or Artist Name will appear on the second line.

Channel Name/Song Title is the default setting for the unit. To toggle between the two display

settings, press SHIFT for less than three seconds.

If text data is longer than eight characters, the display will scroll the information one time, then

only the first eight characters will be displayed. To scroll test again, press and hold FUNC for

more than two seconds. The unit will beep twice, and the data will scroll two times then default to

the first eight characters.

If text data is longer than eight characters, the display will scroll the information one time, then

only the first eight characters will be displayed. To scroll text again, press and hold FUNC for

more than two seconds. The unit will beep twice, and the data will scroll two times then default to

the first eight characters.

Category Mode

Category mode allows a user to select individual channels within a certain category. There are

currently 12 categories to choose from, and each reflects a different type of programming.

Category mode allows a user to select individual channels within a certain category. There are

currently 12 categories to choose from, and each reflects a different type of programming.

While in category mode, Channel Number will always be displayed, and Category Name/

Category Number will be briefly displayed each time a category or channel is selected. After three

seconds, the display will revert to Channel Name/Song Title or Channel Name/Artist Name.

While in category mode, Channel Number will always be displayed, and the Category Name and

Category Number will be briefly displayed each time a category or channel is selected. After three

seconds, the display will revert to Channel Name/Song Title or Channel Name/Artist Name.

The Channel Name will always appear on the first line of the display, and the Song Title or Artist

Name will appear on the second line. Channel Name/Song Title is the default setting for the unit.

To toggle between the two display settings, press SHIFT for less than three seconds.

The Channel Name will always appear on the first line of the display, and the Song Title or Artist

Name will appear on the second line. Channel Name/Song Title is the default setting for the unit.

To toggle between the two display settings, press SHIFT for less than three seconds.

If text data is longer than eight characters, the display will scroll the information one time, then

only the first eight characters will be displayed. To scroll test again, press and hold FUNC for

more than two seconds. The unit will beep twice, and the data will scroll three times.

If text data is longer than eight characters, the display will scroll the information one time, then

only the first eight characters will be displayed. To scroll text again, press and hold FUNC for

more than two seconds. The unit will beep twice, and the data will scroll three times.

MSR4500

Satellite Operation (continued)

Selecting a Mode

Direct mode is set as the default mode for the unit. To select category mode, press FUNC for less

than one second. “CATEGORY” will appear in the lower right corner of the display. To return to

direct mode, press FUNC for less than one second. “DIRECT” will appear in the display.

Direct mode is set as the default mode for the unit. To select category mode, press FUNC for

less than one second. “CATEGORY” will appear in the lower right corner of the display. To return

to direct mode, press FUNC for less than one second. “DIRECT” will appear in the display.

Display

Press DISP to briefly display the time on the display. After five seconds, the display will revert

back to the previously-selected display setting (Channel Name/Song Title or Channel Name/Artist

Name).

Press DISP to briefly display the time on the display. After five seconds, the display will revert

back to the previously-selected display setting (Channel Name/Song Title or Channel Name/Artist

Name).

Seek Tuning

Use seek tuning to move quickly through available channels and categories in either direct or

category mode.

Use seek tuning to move quickly through available channels and categories in either direct or

category mode.

Direct Mode

Press and hold the up (>>) or down (<<) tuning button for more than three seconds, then continue

to hold to seek up or down through all channels. Release the tuning button to stop seeking and

listen to the selected channel.

Press and hold the up (>>) or down (<<) tuning button for more than three seconds, then continue

to hold to seek up or down through all channels. Release the tuning button to stop seeking and

listen to the selected channel.

Category Mode

Press and hold the the up (>>) or down (<<) tuning button for more than three seconds, then

continue to hold to seek up or down through all categories. Release the tuning button to stop

seeking and select the desired category.

Press and hold the the up (>>) or down (<<) tuning button for more than three seconds, then

continue to hold to seek up or down through all categories. Release the tuning button to stop

seeking and listen to the desired category.

Note: In category mode, seek tuning is only used to select a category. Seek tuning cannot

be used to select channels within a category. Use manual tuning to select channels within

a category.

Note: In category mode, seek tuning is only used to select a category. Seek tuning cannot

be used to select channels within a category. Use manual tuning to select channels within

a category.

Satellite Operation

Operación de Satélite

Direct Mode / Modo Directo

Category Mode / Modo Categoria

MSR4500

Satellite Operation (continued)

Manual Tuning

Use manual tuning to move through channels one at a time in either direct or category mode.

Direct Mode

Press the up (>>) or down (<<) tuning button momentarily to select the next sequential channel.

Category Mode

Press the up (>>) or down (<<) tuning button momentarily to select the next sequential channel.

Note: In category mode, manual tuning is only used to select a channel within the current

category. Manual tuning cannot be used to change categories. Use seek tuning to select a

different channel.

Note: In category mode, manual tuning is only used to select a channel within the current

category. Manual tuning cannot be used to change categories. Use seek tuning to select a

different category.

Direct Access Tuning

In direct mode, channels can also be accessed directly by channel number. Press SEL (also the

Scan button), then enter the desired channel number using the number buttons (0-9).

Note: Direct access is used in direct mode only. There is no direct access in category mode.

Scan Tuning

In direct mode, the scan function will scan up through all channels sequentially and provide five

seconds of listening time before moving to the next channel. Press SCAN for more than three

seconds to activate the scan function. While scanning, press SCAN momentarily to stop scanning

and listen to the selected channel.

In direct mode, the scan function will scan up through all channels sequentially and provide five

seconds of listening time before moving to the next channel. Press SCAN for more than three

seconds to activate the scan function. While scanning, press SCAN momentarily to stop scanning

and listen to the selected channel.

Note: Scan tuning is used in direct mode only. There is no scan tuning in category mode.

Tuning Options

Tuning Method

Seek Tuning

Direct Mode

Category Mode

Tuning Method

Seek Tuning

Direct Mode

Category Mode

Tune quickly up or down through

available channels

Tune quickly up or down through

available categories

Tune quickly up or down through

available channels

Tune quickly up or down through

available categories

Tune up or down through all available Tune up or down through all available

Tune up or down through all available

channels within the current category

one at a time

Tune up or down through all available

channels one at a time

channels within the current category

one at a time

Manual Tuning

Tune directly to a channel by entering

the channel number

Tune directly to a channel by entering

the channel number

Direct Access Tuning

N/A

Direct Access Tuning

N/A

Tune up through all channels

sequentially, providing five seconds of

listening at each channel

Tune up through all channels

sequentially, providing five seconds of

listening at each channel

Scan Tuning

MSR4500

Satellite Operation (continued)

Store Preset Channels/Categories

Satellite Operation (continued)

Store Preset Channels/Categories

Preset Channels

Preestablecen el Canal

Up to 20 channels and 20 categories can be stored in

memory for quick recall using the number buttons (0-9).

When a preset is stored, “Preset ##” will appear in the

display for two seconds.

Up to 20 channels and 20 categories can be stored in

memory for quick recall using the number buttons (0-9).

When a preset is stored, “Preset ##” will appear in the

display for two seconds.

Direct Mode

1. To store a single-digit preset (1-9), tune the radio

to the desired channel. Press the desired preset

number button (1-9) for more than three seconds

1. To store a single-digit preset (1-9), tune the radio

to the desired channel. Press the desired preset

number button (1-9) for more than three seconds

to store the current channel.

1. To store a double-digit preset (10-20), tune the radio to the desired channel. Press the first

digit of the desired preset number (1 or 2) momentarily, then press and hold the second digit

(0-9) for more than three seconds to store the selected channel. When entering a double-digit

preset, the second digit must be entered within three seconds of the first or the function will

time out.

2. To store a double-digit preset (10-20), tune the radio to the desired channel. Press the first digit

of the desired preset number (1 or 2) momentarily, then press and hold the second digit (0-9) for

more than three seconds to store the selected channel. When entering a double-digit preset,

the second digit must be entered within three seconds of the first or the function will time out.

Category Mode

1. To store a single-digit preset (1-9), tune the radio to the desired category. Press the desired

preset number button (1-9) for more than three seconds to store the current category.

1. To store a single-digit preset (1-9), tune the radio to the desired category. Press the desired

preset number button (1-9) for more than three seconds to store the current category.

2. To store a double-digit preset (10-20), tune the radio to the desired category. Press the first

digit of the desired preset number (1 or 2) momentarily, then press and hold the second digit (0-

9) for more than three seconds to store the selected category. When entering a double-digit

preset, the second digit must be entered within three seconds of the first or the function will time

out.

2. To store a double-digit preset (10-20), tune the radio to the desired category. Press the first

digit of the desired preset number (1 or 2) momentarily, then press and hold the second digit

(0-9) for more than three seconds to store the selected category. When entering a double-digit

preset, the second digit must be entered within three seconds or the function will time out.

Recall Preset Channels/Categories

Once preset channels and categories are stored into memory, they can be quickly and

automatically accessed by pressing the corresponding preset number button.

Once preset channels and categories are stored into memory, they can be quickly and automatically

accessed by pressing the corresponding preset number button.

Direct Mode

1. To recall a single-digit preset (1-9), press the desired preset number button for less than three

seconds to access the corresponding channel.

1. To recall a single-digit preset (1-9), press the desired preset number button for less than three

seconds to access the corresponding channel.

2. To recall a double-digit preset (10-20), press the first digit of the desired preset number (1 or 2)

momentarily, then press the second digit (0-9) momentarily to access the selected channel.

When entering a double-digit preset, the second digit must be entered within three seconds of

the first or the function will time out.

2. To recall a double-digit preset (10-20), press the first digit of the desired preset number (1 or 2)

momentarily, then press the second digit (0-9) momentarily to access the selected channel.

When entering a double-digit preset, the second digit must be entered within three seconds of

the first or the function will time out.

Category Mode

1. To recall a single-digit preset (1-9), press the desired preset number button for less than three

seconds to access the corresponding category.

1. To recall a single-digit preset (1-9), press the desired preset number button for less than three

seconds to access the corresponding category.

2. To recall a double-digit preset (10-20), press the first digit of the desired preset number (1 or 2)

momentarily, then press the second digit (0-9) momentarily to access the selected category.

When entering a double-digit preset, the second digit must be entered within three seconds of

the first or the function will time out.

2. To recall a double-digit preset (10-20), press the first digit of the desired preset number (1 or 2)

momentarily, then press the second digit (0-9) momentarily to access the selected category.

When entering a double-digit preset, the second digit must be entered within three seconds of

the first or the function will time out.

MSR4500

Satellite Operation (continued)

Skip and Restore Channels

In direct mode, the radio can be programmed to skip selected channels. There is no skip function

in category mode.

In direct mode, the radio can be programmed to skip selected channels. There is no skip function

in category mode.

Skip Channel

1. Select direct mode.

2. Use direct access to select the channel you want to skip.

3. Press FUNC and SELECT simultaneously for more than three seconds.

2. Use direct access to select the channel you want to skip.

3. Press FUNC and SELECT simultaneously for more than three seconds.

The selected channel will now be skipped during seek, manual, and scan tuning. It can still be

selected through direct access tuning.

The selected channel will now be skipped during seek, manual, and scan tuning. It can still be

selected through direct access tuning.

Restore Channel

1. Select direct mode.

1. Use direct access to select the channel you want to restore.

2. Press FUNC and SELECT simultaneously for more than three seconds.

1. Use direct access to select the channel you want to restore.

2. Press FUNC and SELECT simultaneously for more than three seconds.

The selected channel will now be restored for seek, manual, and scan tuning as well as direct

access tuning.

The selected channel will now be restored for seek, manual, and scan tuning as well as direct

access tuning.

Invalid Channels

If an invalid channel is selected, “Invalid Channel” will appear momentarily on the display. After

three seconds, the display will revert back to the previous active channel.

If an invalid channel is selected, “Invalid Channel” will appear momentarily on the display. After

three seconds, the display will revert back to the previous active channel.

Accessing the Sirius ID Number

1. Use direct access to select channel number “000”.

2. The 12-digit Sirius ID number will be displayed for 15 seconds.

3. Press FUNC to revert back to the previous mode before the 15 seconds are over.

2. The 12-digit Sirius ID number will be displayed for 15 seconds.

3. Press FUNC to revert back to the previous mode before the 15 seconds are over.

Non-Subscribed Channels

Unsubscribe Channels

If a channel not currently subscribed to is selected, “Call 888.539.SIRIUS To Subscribe” will scroll

across the display two times. To scroll data again, press FUNC for more than three seconds.

Preview Channel

The preview channel can be accessed to verify proper installation and operation.

1. Select direct mode.

2. Use direct access to select channel 184.

3. If preview channel functions properly, contact Sirius at 888-539-SIRIUS to subscribe.

The Sirius preview channel is a special content channel with program audio that can only be

tuned prior to customer subscription.

The Sirius preview channel is a special content channel with program audio that can only be

tuned prior to customer subscription.

MSR4500

CD Player Operation

Insert CD

Operatión del Reproductor de CD

Para Insertar el CD

Inserting and Ejecting CD

Para Insertar y Expulsar el CD

1. Press OPEN. Faceplate will flip down.

2. Insert CD into slot with the label side facing up.

3. Flip the faceplate up to close.

1. Presione OPEN. La placa frontal se abrirá hacia abajo.

2. Inserte el CD con la etiqueta haca arriba en la ranura.

3. Levante el panel hacia arriba para cerrar.

Eject CD

Para Expulsar el CD

1. Press OPEN. Faceplate will flip down.

1. Presione OPEN. La placa frontal se abrirá hacia abajo.

2. Press the eject button to eject the CD from the slot.

The power does not need to be on to eject the CD.

2. Presione el boton de expulsar para expulsar el CD de la

ranura. No es necesario que el radio esté encendido para

expulsar el CD.

3. Flip the faceplate up to close.

3. Levante el panel hacia arriba para cerrar.

Note: Do not expose the CD player to extremely high or low temperatures. Do not drive with

an ejected CD in the slot.

Nota: No exponga el reproductor de CD a temperaturas extremas. No conduzca su vehiculo

con el CD expulsado por la ranura del reproductor de CD.

Repetir (RPT)

Repeat (RPT)

CD Player Operation

Operación del Reproductor de CD

Presione RPT para repetir

Press RPT for more than three

continuamente la misma posta. En el

visualizador aprece “RPT”. Presione

de nuevo por mas de tres segundos

para detener la repetición.

seconds to continuously repeat the

same track on a CD. The “RPT”

icon appears in the display. Press

RPT again for more than three

seconds to stop repeating, and the

“RPT” icon will disappear.

Reproducción Aleatoria

(RDM)

Random (RDM)

Presione RDM para reproducir una

vez todas las pistas del CD en orden

aleatorio. En el visualizador aparece

“RDM”. Presione de neuvo por mas

de tres segundos para detener la

reproducción al azar.

Press RDM for more than three

seconds to play all tracks on a CD in

random order one time. The “RDM”

icon appears in the display. Press

RDM again for more than three

seconds to stop random play, and

the “RDM” icon will disappear.

Intro (INT)

Presione INT para reproducir los

primeros diez segundos de cada

pista del CD actual. En el

visualizador aparece “INT”. Presione

de nuevo por mas de tres segundos

para detener INT y escuchar la pista.

Intro (INT)

Press INT for more than three

seconds to play the first ten seconds

of each track on a CD. The “INT”

icon appears in the display. Press

INT again for more than three

seconds to stop intro and listen to

track, and the “INT” icon will

disappear.

MSR4500

CD Player Operacion / Operación del Reproductor de CD

Open

Play / Pause

Reproducir / Pausa

Fast Forward and Fast Reverse

Avance y Retroceso Rápidos

Number Buttons (1 - 10)

Los Botones Numeradas (1 - 10)

Program / Programa

Repeat / Repitir

Intro / Intro

Random / Reproducción Aleatoria

Operatión del Reproductor de CD (continuado)

CD Player Operation (continued)

Modo Programa

Program Mode

Presione PGM por más de tres segundos. El icono programa empieza a destellar lo que le indica

Press PGM for more than three seconds. The PROGRAM icon will flash on the display when

que usted está ahora en el modo programa.

program mode is accessed.

Programe hasta 24 pistas de CD para reproducirlas en cualquier orden seleccionando una pista

por cada punto de la secuencia de reproduccion. En el modo programa, el visualizador mostrara

uno de los siguiented indicadores: P-01 (el programa está vacio), P-24 (la última pista en

memoria), PR-C (el programa ha sido borrado), o FULL (el programa está lleno).

Program up to 24 CD tracks to play in any order by selecting a track for each spot in the playing

sequence. In program mode, the display will show one of the following: P-01 (program is empty),

P-24 (last track in memory), PR-C (program has been cleared), or FULL (program is full).

You must be in program mode to perform the following functions:

Usted debe estar en el modo programa para ejecutar las sigulented funciones:

Store Tracks in Memory

Almacenar Pistas en la Memoria

Press << or >> to select a track number. Press PGM to program the selected track into memory.

Presione << ó >> para seleccionar el número de pista. Presione PGM para programar en la

“P-02” will appear in the display. Repeat to program up to 24 tracks into memory.

memoria la pista seleccionada. En el visualizador aparecerá “P-02”.

Play Program

Reproducir el Programa

Press the Play/Pause button to begin play or to pause play at any time.

Presione el botón de reproducir/pausa para reproducir o para pausa en cualquier momento.

Clear Program

Borrar el Programa

Press PGM for more than three seconds to clear the current program from memory.

Presione PGM por más de tres segundos para borrar el programa del la memoria.

Fast Forward and Fast Reverse

Avance y Retroceso Rápidos

Press and hold << or >> to fast forward or fast reverse a track. CD play will resume after the

Presione y sostenga << ó >> para retroceder o avanzar rápidamente una pista. La reproducción

button is released.

del CD se reanuda luego que se suelta el botón.

Skip Tracks

Para Saltar las Pistas

Press << or >> to advance to the next or previous track. The track number will appear in the

Presione << ó >> para ir a la anterior o a la siguiente pista. En el visualizador aparece el número

display.

de la pista.

Direct Track Access

Acceso Directo a la Pista

Select the track number by pressing the numbered keys (1-0). For example, to access track 12,

press button 1 followed by button 2. If selected track is not on the disk, “No Track” appears in the

display.

Seleccione el número de pista presionando las teclas muneradas (1-0). Si la pista seleccionada no

está en el disco, en el visualizador aparace “No Track”.

MSR4500

Operación de la Radio

CD Changer Operation

CD Changer Mode

Nota: El MSR4500 está deseñado para

controlar un cambiadiscos opcional de

CD. El cambiador de discos compactos

reproduce todas las sanciones en el disco

y luego en orden avanza al siguiente

disco. Las funciones de Saltar Pistas,

Acceso Directo a Pistas, Avance y

Retroceso Rápidos, Pausa, Repetición,

Reproduducción Aleatoria y Rastrea

pueden realizarse en los discos

Note: The MSR4500 is designed to control

an optional CD changer. The compact disc

changer plays all songs on a disc then

advances to the next disc in order. Skip

Tracks, Direct Track Access, Fast

Forward, Fast Reverse, Pause, Repeat,

Random and Intro Scan functions can be

performed on CD’s played through the CD

changer. See CD player instructions for

details on performing these functions.

Modo del Cambiadiscos de CD

compactos reproducidos por medio del

cambiadiscos de CD. Vea las

instrucciones del Reproductor de CD.

Direct Disc Access

Accesso Directo al Disco

Press SHIFT, then select the disc number using the number keys. If the selected disk is not in the

Presione SHIFT y luego seleccione el número de disco utilizando las teclas numeradas. Si el disco

changer, “No Disk” appears in the display.

seleccionado no está en el cambiadiscos, en el visualizador aparece “No Disk”.

Note: Depending on the CD changer, if selected disc tray is empty, the CD changer may

either advance to the next disc or revert back to the previous disc.

Nota: Dependiendo del cambiadiscos de CD, si la bandeja del disco seleccionado está vacía,

el cambiadiscos de CD puede ya sea avanzar al siguiente disco o volver al disco anterior.

Program Mode

Modo Programa

Press PGM for more than three seconds. The PROGRAM icon will flash on the display when

Presione PGM por más de tres segundos. El icono programa empieza a destellar lo que le indica

program mode is accessed.

que usted está ahora en el modo programa.

Program up to 32 CD tracks to play in any order by selecting a track for each spot in the playing

sequence. In program mode, the display will show one of the following: P-01 (program is empty),

P-32 (last track in memory), PR-C (program has been cleared), or FULL (program is full).

Programe hasta 32 pistas de CD para reproducirlas en cualquier orden seleccionando una pista por

cada punto de la secuencia de reproduccion. En el modo programa, el visualizador mostrara uno de

los siguiented indicadores: P-01 (el programa está vacio), P-32 (la última pista en memoria), PR-C

(el programa ha sido borrado), o FULL (el programa está lleno).

You must be in program mode to perform the following functions:

Usted debe estar en el modo programa para ejecutar las sigulented funciones:

Store Tracks in Memory

Almacenar Pistas en la Memoria

1. Press SHIFT then select disc number using number keys.

2. Press << or >> to select a track number.

1. Presione SHIFT para seleccionar el número de disco usando las tecias numericas.

2. Presione << ó >> para seleccionar el número de pista.

3. Press PGM to program the selected track into memory. “P-01” will appear in the display.

4. Repeat to program up to 32 tracks into memory.

3. Presione PGM para programar en la memoria la pista seleccionada. En el visualizador

aparecerá “P-01”.

Play Program

4. Repita igual para programar en la memoria hasta 32 pistas.

Press the Play/Pause button to begin play or to pause play at any time.

Reproducir el Programa

Clear Program

Presione el botón de reproducir/pausa para reproducir o para pausa en cualquier momento.

Press PGM for more than three seconds to clear the current program from memory.

Borrar el Programa

Presione PGM por más de tres segundos para borrar el programa del la memoria.

MSR4500

Especificationes

Specifications

Reproductor de CD

CD Player

Promedio de ruido/señal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>86 dB

Respuesta de frecuencia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Hz - 20 kHz

Separación de canales. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>65 dB

Transformador D/A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Bit/CH

Signal/noise ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >86 dB

Frequency response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Hz - 20 kHz

Channel separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >65 dB

D/A converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Bit/CH

Sintonización FM

FM Tuner

Alance de sintonización . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87.5 MHz - 107.9 MHz

Sensibilidad mono FM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 dBf

50 dB de umbral de sensibilidad (estereo). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 dBf

Separación de esteréo a 1 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40dB

Tuning range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87.5 MHz - 107.9 MHz

FM mono sensitivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 dBf

50 dB quieting sensitivity (stereo) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 dBf

Stereo separation @ 1 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40dB

Sintonización AM

AM Tuner

Alance de sintonización . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .530 kHz - 1720 kHz

Tuning range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530 kHz - 1720 kHz

Amplificador

Amplifier

Capacidad total de corriente. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 watts pico

Salida de corriente . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 x 50W

Total system power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 watts peak

Power output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 x 50W

General

Suministro de corriente . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-16 VDC, negativo a tierra

Impedancia de salida del altoparlante . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8 Ohmios

Fusibles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .fast blow ATO (10 ampieros)

Dimensiones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7” x 6” x 2” (178mm x 155mm x 51mm)

Power supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-16 VDC, negative ground

Speaker output impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8 Ohms

Fuses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . fast blow ATO (10 amp)

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7” x 6” x 2” (178mm x 155mm x 51mm)

Las especificationes están sujetas a cambio sin previo aviso.

Specifications subject to change without notice.

MSR4500

Troubleshooting

Corrección de Problemas

Problema

Causa

Correccion

Problem

Cause

Corrective Action

El equipo no funciona No hay corriente en el cable amarillo; no Revise la conexión con la luz de prueba;

Does not operate (display No power to yellow wire, or no power to Check connection with test light; check

(el visualizador ne se

enciende)

hay corriente en el cable rojo

revise el fusible del barco con la luz de

prueba

does not light)

red wire

boat fuse with test light

Replace fuse

Inline fuse blown

Speaker harness not connected

El fusible en-linea está quemado

Reemplace el fusible

No power to unit

Check/replace fuse

La alimentatión no va a El fusible en-linea está quemado

la unidad

Examine/reemplace el fusible

Speakers not operating

(display lights normally)

Connect speaker harness; check

speaker wires

Ninguno de los

El colector del altoparlante no está

Cenecte el colector de cables del

altoparlante; revise los cables del

altoparlante

Not all speakers operate Incorrect splices or connections

Check all splices and connections

Check splices; insulate all bare wires

altoparlantes funciona conectado

(las luces del visualidor

funcionan)

Speaker wires shorting to chassis

ground to to each other

No todos los

altoparlanted funcionan

Conexiones o conectored incorrectas

Examine todas las conexiones y los

conectores

Blows fuses

Power wire shorting to ground

Speaker wires shorting to ground

Incorrect fuse/fuse too small

Make sure wire is not pinched

Make sure wire in not pinched

Install fuse of correct rating

Press RESET button

Los cables del altoparlante hacen

cortocircuitos hasta la conexión a tierra

Examine las conexiones y recubra los

cables pelados con cinta aislante

ER-1 appears on display Disc loading malfunction

Fusibles quemados

El cable hace cortocircuito en la conexión Asegurese de que el cable no esté

a tierra

ER-2 appears on display Disc loading/eject malfunction

Press RESET button

pellizcado

CD skips too much

Receiver mount is not solid or backstrap Check mounting and backstrap; tighten if

Los cables del altoparlante producen

cortocircuitos en la conexión a tierra

Asegurese de que el cable no esté

pellizcado

is not secure

needed

No sound

Loss of signal *

See note *

Fusible incorrecto/fusible demasiado

pequeño

Instale el fusible de voltaje apropiado

Satellite mode not selected

Audio cable not connected

Satellite mode not selected

Audio cable not connected

Satellite antena cable not connected

Faulty antenna cable

Ensure Satellite mode is selected

Ensure proper cable connections

Ensure Satellite mode is selected

Ensure proper cable connections

Check cable connections

Replace antenna cable

ER-1 en el visualizador Mal funcionamiento de la carga de disco Presione el botón RESET

ER-2 en el visualizador Disco cargando/mal funcionamiento del

expulsor

Presione el botón RESET

Intermittent sound

El CD salta demasiado El montaje del receptor ne está sólido o la Revise la correa de montaje y retención;

correa de retensión no está bien segura ajustela si es necessario

Antenna disconnected

No hay sonido

Pérdida de la señal*

Vea nota*

Technical assistance is available Monday through Friday from 8:00 AM until 5:00 PM EST by calling 1-800-

323-0221. To receive technical information at any time, visit www.jensen.com.

Modo basado en los satélites no

seleccionado

Seleccione el modo basado en los

satélites

Cable(s) de audio no conectado(s)

Revise las conexiones del cable

* Note: Man-made objects (metal truss-type bridges, tall buildings, tunnels, etc.) and

natural objects (mountains, canyons, valleys, etc.) can cause a loss of satellite and

terrestrial signals momentarily. If the signal is lost, the DLP will try and reacquire the

satellite and/or terrestrial signal(s). When the DLP is repeatedly trying to reacquire a

signal, the sound will be intermittent.

Sonido intermitente

Modo basado en los satélites no

seleccionado

Seleccione el modo basado en los

satélites

Cable(s) de audio no conectado(s)

Revise las conexiones del cable

Antena desconectada El cable de la antena no está conectado Revise las conexiones del cable

Cable de la antena defectuoso Reemplace la antena

La asistencia técnica es lunes disponible a viernes a partir de la 8:00 y de 5:00 P.M. EST llamando 1-800-323-

0221, o la visita www.jensen.com en cualquier momento.

*Nota: Los objetos hechos por el hombre (puentes metálicos tipo armadura, edificios

altos, túneles, etc.) y objetos naturales (montañas, cañones, valles, etc.) pueden ocasionar

pérdida momentánea de las señales del satélite y terrestres. Si la señal se pierde el DLP

tratará de recuperar la(s) señal(es) del satélite y/o terrestres. Cuando el DLP está tratando

repetidamente de captar una señal, el sonido será intermitente.

MSR4500

Garantía

Warranty

Garantía limitada por un año – en los Estados Unidos de América y Canadá

Limited One Year Warranty–USA & Canada

Plazo de garantía: Esta garantía de Recoton Mobile Electronics es válida por un año a partir de la

fecha de compra del primer comprador.

Length of Warranty: This warranty from Recoton Mobile Electronics shall be in effect for a

period of one year from the date of the first consumer purchase.

Personas Protegidas: Esta garantía tiene validez para el dueño original y los dueños subsiguientes

durante el período de garantía siempre que se pueda presentar prueba de la fecha de compra de un

representante autorizado de Jensen dondequiera que se requieran servicios cubiertos por la garantía.

Persons Protected: This warranty will be enforceable by the original owner and any

subsequent owners during the warranty period so long as proof of date of purchase from an

authorized Jensen dealer is presented whenever warranty service is required.

Cobertura de la Garantía: Salvo especificación contraria, esta garantía cubre todos los desperfectos

de material y de mano de obra del producto. A continuación se detalla lo que no está cubierto por la

garantía: daños producidos debidos a accidentes, uso inapropiado, abuso, negligencia, modificación

del producto, instalación incorrecta, voltaje inadecuado, reparaciones no autorizadas o errores por no

haber seguido las instrucciones provistas junto al producto, daños ocurridos durante el envío (los

reclamos deben presentarse al transportista), eliminación de estática o interferencias eléctricas,

cualquier producto comprado fuera de los Estados Unidos de América en el cual se haya modificado,

borrado o removido el número de serie.

What is Covered: Except as otherwise specified below, this warranty covers all defects in

material and workmanship in this product. The following are not covered: damage resulting

from accident, misuse, abuse, neglect, product modification, improper installation, incorrect

line voltage, unauthorized repair or failure to follow instructions supplied with the product;

damage occurring during shipment (claims must be presented to the carrier); elimination of

boat static or other electrical interferences; any product purchased outside USA, or on which

the serial number has been defaced, modified or removed.

How You Can Get Service: Please telephone Jensen at 1-800-323-4815. We will either

inform you of the name and address of an authorized Jensen repair station which will service

the product or will advise you to send the product to a factory service center.

Cómo conseguir el servicio: Por favor ponerse en contacto con Jensen al teléfono 1-800-323-4815.

Le daremos el nombre y dirección de una casa autorizada por Jensen para realizar reparaciones o le

aconsejaremos que envíe el producto a un centro de fabricación.

If shipment of the product is required, it should be packed securely. The original dated bill of

sale must always be included with the product as proof of warranty coverage.

Si se requiere el envío del producto, se deberá empaquetarlo en forma adecuada. Siempre se deberá

incluir la factura original con la fecha de compra junto al producto como prueba de la cobertura de

garantía.

What We Will Pay For: We will pay for all labor and material expenses required to repair the

product, but you must pay any labor costs for the removal and/or installation of the product. If

the product is shipped for warranty service, you must prepay the initial shipping charges, but

Jensen will pay the return shipping charges if the product is returned to an address inside the

USA or Canada.

Costos Cubiertos: El fabricante pagará los costos de mano de obra y de material que se requieran

para la reparación del producto, pero el comprador se hará cargo de los costos de mano de obra

necesarios para desmontar y/o instalar el producto. Si el producto es enviado para servicios cubiertos

por la garantía, el comprador debe pagar los costos iniciales del envío pero Jensen se hará cargo de

los costos de envío al comprador si el producto es devuelto desde una dirección de los EE.UU. o

Canadá.

Exclusion of Certain Damages: Jensen’s liability is limited to the repair or replacement, at

our option, of any defective product and shall not include incidental or consequential economic

damages of any kind.

Exclusión de Ciertos Daños: La responsabilidad de Jensen se limita a la reparación y reemplazo del

producto, según su propia decisión, por cualquier artículo defectuoso y no incluye daño económico o

incidental de cualquier naturaleza.

Some states and/or provinces do not allow limitations on how long an implied warranty lasts

and/or do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitations and exclusions may not apply to you.

Algunos estados y/o provincias no permiten limitaciones de la garantía en cuanto a la duración de la

garantía y/o no permiten la exclusión o limitación sobre daños emergentes o incidentales, de modo

que las limitaciones previamente indicadas pueden no aplicarse en su caso.

This warranty gives you specific legal rights, and you may also have other rights which vary

from state to state and province to province.

Esta garantía le otorga un derecho específico y usted puede ejercer otros derechos que varían

conforme al estado o provincia de su residencia.

Recoton Mobile Electronics, Inc.

1090 Emma Oaks Trail

Lake Mary, FL 32746

1-800-323-0221

www.jensen.com

Yamaha RX N600D User Manual
Wharfedale RS10 User Manual
Weil McLain SERIES 2 LGB 13 User Manual
Vivitar Camera Lens VIV 7MM S User Manual
Toshiba MA 1190 User Manual
Speco Technologies VM 1205B User Manual
SoundMax SM CMD3011 User Manual
Sony HANDYCAM CX360V User Manual
Samsung SyncMaster 172MP User Manual
Samsung 2063UW User Manual