Siemens SIMATIC NET CP 343 1 User Manual

SIMATIC NET

Produktinformation

C79000–Z8964–C038–05

Product Information

Information produit

Informazioni sul prodotto

Información sobre producto

Stand/ Dated/ Edition/ Versione/ Versiòn 06/99

CP 343–1

6GK7 343-1BA00-0XE0

ab Ausgabestand 7 (FW–Stand V5.00)

version 7 or higher (firmware V5.00)

à partir de la version 7 (microprogramme V5.00)

a partire dalla versione 7 (versione FW V4.00)

a partir de la versión 7 (FW-V5.00)

SIMATIC S7–300

Deutsch / English / Français / Italiano / Español

E SIEMENS AG 1998

Änderungen vorbehalten

Subject to alteration

Sous réserve de modifications

Con riserva di modifiche

Sujeto a cambios

english

Contents

Notes for the Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

The CP 343-1 Communications Processor . . . . . . . . . . . . . . .

1.1 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.2 Performance Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.2.1 Characteristics of S7 Communication . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.2.2 Characteristics of ISO Transport Connections . . . . . . . . . . . . . . . . . . .

1.3 Displays and Mode Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.4 Further Information on Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1 Module Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3 Attaching the CP 343-1 to Industrial Ethernet . . . . . . . . . . . . . . . . . . . .

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.1 General Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.2 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.3 Notes on the CE Approval of SIMATIC NET Products . . . . . . . . . . . . .

References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Compatibility with the Previous Version

The version of the CP 343-1 described here is functionally compatible with and can

be used to replace the CP 343-1 with order number 6GK7 343–1BA00–0XE0 ver-

sion 6.

The CP 343-1 decribed here has more functions. Refer to the information in

Section 1.1.

Reply Form (at the end of this product information):

We would like to know the purpose for which you are using this module

and would also like to know your opinion of the module and the documen-

tation. You can help us to provide you with better support and to further

improve the product. We would be grateful if you would complete the reply

form and return it to us by post or fax.

Productinformation CP 343–1

C79000–Z8964–C038–05

english

Notes for the Reader

Safety Guidelines

This manual contains notices which you should observe to ensure your

own personal safety, as well as to protect the product and connected

equipment. These notices are highlighted in the manual by a warning

triangle and are marked as follows according to the level of danger:

Note

draws your attention to particularly important information on the product, handling

the product, or to a particular part of the documentation.

Caution

indicates that minor personal injury or property damage can result if proper pre-

cautions are not taken.

Warning

indicates that death, severe personal injury or substantial property damage can

result if proper precautions are not taken.

Danger

indicates that death, severe personal injury or substantial property damage will

result if proper precautions are not taken.

DisclaimerofLiability

The reproduction, transmission or use of this document or its

contents is not permitted without express written authority.

Offenders will be liable for damages. All rights, including rights

createdbypatentgrantorregistrationofautilitymodelordesign,are

reserved.

Wehavecheckedthecontentsofthismanualforagreementwiththe

hardware and software described. Since deviations cannot be

precludedentirely, we cannot guarantee full agreement. However,

the data in this manual are reviewed regularly and any necessary

corrections included in subsequent editions. Suggestions for

improvementare welcomed.

Siemens AG

A&D

Technical data subject to change.

IndustrialAutomationSystems

Postfach4848, D-90327Nürnberg

Productinformation CP 343–1

C79000–Z8964–C038–05

english

The CP 343-1 Communications Processor

Application

The CP 343-1 communications processor is designed for operation in an

S7-300 programmable logic controller. It allows the S7-300 to be attached to

Industrial Ethernet.

LED displays

Mode selector

AUI/ITP interface

15-pin sub D

with sliding locking

mechanism

Figure 1 CP 343-1

Design

The module has been designed to match the components of the S7-300

programmable logic controller and has the following features:

S Double-width module for simple installation in the S7-300 rack.

S The operator controls and displays are all located on the front panel.

S No fan necessary.

S Direct backplane bus connection of the modules via accompanying

backplane module connectors.

S 15-pin sub D female connector with sliding locking mechanism for

attaching the CP 343-1 to Industrial Ethernet (automatic switchover

between the AUI interface and Twisted Pair interface).

Productinformation CP 343–1

C79000–Z8964–C038–05

english

Configuration

You can configure the CP 343–1 via MPI or LAN/Industrial Ethernet. You re-

quire STEP 7 with the following version of NCM S7 for Industrial Ethernet

(abbreviated to ”NCM IE” below):

Table 1

Version STEP7/NCM IE

Functionality of the CP 343–1

V2.x to V5.x

The same functionality is available as with the previous

versions of the CP.

S Configuration data created with these STEP 7 or NCM

versions can be downloaded to the CP 343–1.

V5.x + SP2 or higher

The full functionality including the extended functions as

listed in Section 1.1 can be used.

Information about the required service pack (SP2) is

available on the Internet at:

http://www.ad.siemens.de/csi/net

1.1

Characteristics

Services

The CP 343-1 supports the following communication services:

S S5-compatible communication with

– SEND/RECEIVE interface via ISO transport connections

– FETCH/WRITE services (passive; according to the S5 protocol) via

ISO transport connections and ISO-on-TCP connections

S S7 communication with

– PG functions

– Operator control and monitoring functions

– Data exchange using communication function blocks

PG functions:

Using the PG functions, modules such as the FM 354 or FM 355 can be

accessed via the CP (“extended” PG functions).

Productinformation CP 343–1

C79000–Z8964–C038–05

english

Note

If there is a diagnostic connection to the CP via the CPU, configuration

data cannot be downloaded automatically to the CP by the CPU at the

same time!

Extended Functions Compared with Version 5

S Reading and writing data in the FETCH/WRITE mode

The services FETCH and WRITE are supported for direct access to sy-

stem memory areas on the SIMATIC S7 PLC via ISO transport and and

ISO-on-TCP connections. The SIMATIC S7-300 with the CP 343-1 is

always the server (passive connection establishment), while the fetch or

write access (client functionality with active connection establishment)

originates from a SIMATIC S5 PLC or other device

Requirements – General Operation

The following table shows the S7–300 CPUs with which the CP 343–1 can be

operated with this range of functions:

Table 2

CPU

MLFB–Number

CPU 312 IFM

6ES7 312–5AC02–0AB0

6ES7 312–5AC82–0AB0

6ES7 313–1AD03–0AB0

6ES7 314–1AE04–0AB0

6ES7 314–1AE84–0AB0

6ES7 314–5AE03–0AB0

6ES7 314–5AE83–0AB0

6ES7 315–1AF03–0AB0

6ES7 315–2AF03–0AB0

6ES7 315–2AF83–0AB0

6ES7 316–2AG00–0AB0

6ES7 318–2AJ00–0AB0

CPU 312 (T)

CPU 313

CPU 314

CPU 314 (T)

CPU 314 IFM

CPU 314 IFM (T)

CPU 315

CPU 315–2 DP

CPU 315–2 DP (T)

CPU 316–2 DP

CPU 318–2

Productinformation CP 343–1

C79000–Z8964–C038–05

english

Table 2

CPU

MLFB–Number

CPU 614

6ES7 614–1AH03–0AB3

6ES7 614–1AH03–0AB3–Z

CPU 614–Z

The table lists the CPUs approved at the time of printing this product informa-

tion bulletin. S7–300 CPUs approved later and not listed in the table also

support the range of functions described here.

All versions of the SINUMERIK CPUs 840D and 810D are supported.

Requirements – ISO Transport Connections

The following conditions must be taken into account on ISO transport con-

nections depending on the length of the data to be transferred:

Table 3

Functionality

Requirement

Transfer of

data fields <= 240 bytes

The blocks AG_SEND FC5 and AG_RECV FC6 or as an

alternative the blocks AG_LSEND FC50 and AG_ LRECV

FC60 are required.

Transfer of data

Note the two requirments below:

fields > 240 bytes

S You require the blocks AG_LSEND FC50 and

AG_LRECV FC60. These blocks are shipped with

NCM V 4.02 with service pack 1.

The blocks are shipped as standard components of

newer versions of NCM.

S Configuration:

When configuring the CP 343–1 with Hardware

Configuration in STEP 7, select the option “Data length

> 240 bytes” under the “Options” tab.

Productinformation CP 343–1

C79000–Z8964–C038–05

english

1.2

Performance Data

1.2.1

Characteristics of S7 Communication

The functions and characteristics of S7 communication are described in /8/

and /11/.

1.2.2

Characteristics of ISO Transport Connections

The following information is important for operating ISO transport connections

(SEND/RECEIVE interface):

Table 4

Characteristic

Explanation / Values

Total number of connections on Industrial

Ethernet

32 maximum

Number of connections for S7 communication The actual value depends on the CPU type

on Industrial Ethernet

being used. Please refer to /1/ for the values

for your CPU.

Number of ISO transport connections

16 maximum

Maximum data length for AG_SEND and

AG_RECV blocks

AG_SEND and AG_RECV allow the transfer

of data fields of between 1 and 240 bytes.

Maximum data length for AG_LSEND and

AG_LRECV blocks

AG_LSEND and AG_LRECV are shipped for

the CP 343–1 from version 5 or higher

(firmware V3.00) and permit the transfer of

data fields of between 1 and 8192 bytes (for

more detailed information, see Table 3 ).

Reaction Times of ISO Transport Connections

The calculation of the reaction times with ISO transport connections is deter-

mined by the run time of the function blocks required on the S7-300 CPU

(AG-SEND, AG–RECV).

Productinformation CP 343–1

C79000–Z8964–C038–05

english

Table 5

Component

Explanation / Values

Run time in the CPU 314-1

per block

AG-SEND/AG-LSEND,

AG-RECV/AG-LRECV

2.5 ms to 5 ms

1.3

Displays and Mode Selector

LED Displays

The LED panel on the front of the CP 343-1 has three display elements:

RUN

STOP

Figure 2 LED Displays

CP Operating Mode

The LEDs indicate the current operating mode of the CP 343-1 as follows:

STOP–LED

RUN–LED

SF–LED

CP operating mode

(yellow)

(green)

(red)

start up

RUN

STOPPING

STOP

STOP with internal error

Productinformation CP 343–1

C79000–Z8964–C038–05

english

STOP–LED

(yellow)

RUN–LED

(green)

SF–LED

(red)

CP operating mode

Module fault / system error

flashing

Legend:

lit

off

Note

Read the explanations of the operating modes in the NCM S7 for

Industrial Ethernet manual /8/.

Controlling the Operating Mode

There are three ways in which you can control the mode of the CP 343-1, as

follows:

S Mode selector

S From a PG/PC. You can also control the modes using the configuration

software in STEP 7, as follows .

– NCM S7, Diagnostics for Industrial Ethernet (see /8/);

– SIMATIC Manager\CP343-1\PLC\Operating Mode

Mode Selector

With the mode selector, you can set the following modes:

S Switch from STOP to RUN:

In the RUN mode, all communication services are available.

The CP modes can only be controlled using NCM S7 or the SIMATIC

Manager when the selector is set to RUN.

S Switch from RUN to STOP:

The CP changes to the STOP mode.

In the STOP mode, only the configuration and diagnostic functions are

available on the CP 343-1.

Productinformation CP 343–1

C79000–Z8964–C038–05

english

Note

Read the sections about downloading configuration data to the CP in the

NCM S7 for Industrial Ethernet manual /8/.

1.4

Further Information on Operation

Downloading Firmware

The CP 343-1 supports firmware updates using the Firmware Loader.

An update of the firmware can be downloaded from the PC/programming de-

vice at any time. After downloading the firmware, the CPU must be reconfigu-

red (power off/on or memory reset).

For more information on downloading the firmware, refer to the README file

of the NCM S7 for Industrial Ethernet configuration software.

Note

Read the information on downloading a database to the CP in the

NCM S7 manual /8/.

Group status “8183” on the FC call interface

The return values DONE=0; ERROR=1; Status=8183 can be caused by the

following states:

S The CP is in the STOP mode.

S The connection is not configured.

S The connection is not established

Productinformation CP 343–1

C79000–Z8964–C038–05

english

Status on the FC call interface; special situation with FC versions

With the FCs AG_SEND (FC 5) and AG_RECV (FC 6), you receive the follo-

wing return values after a connection is aborted:

S AG_SEND: DONE=1; ERROR=0; Status=0000_H

S AG_RECV: DONE=0; ERROR=1; Status=8183_H

The new FCs for longer data fields (FC AG_LSEND and AG_LRECV) react in

exactly the same way to a connection abort, in other words with the return

values

S DONE=0; ERROR=1; Status=8183

Influence of MPI Connections on Connections via Industrial Ethernet

If a station on MPI is added or removed, for example because a service PG

has been connected or disconnected, it is possible that all the connections on

the communications bus are aborted. This has the following effects on the

communication connections on Industrial Ethernet:

S All S7 connections are temporarily aborted.

S The ISO Transport connections on which a job with a data length > 240

bytes is being processed are aborted.

The return values must be handled accordingly on the FC interface in the

user program.

Installation

2.1

ModuleAccessories

The accessories required to attach the CP 343-1 to an Industrial Ethernet

LAN must be ordered separately. For more detailed information, see /9/, /10/,

/12/.

Productinformation CP 343–1

C79000–Z8964–C038–05

english

2.2

Procedure

Steps in Installation

Installing the CP 343-1 involves the following steps.

S Plug in the CP 343-1 and secure it with the screws (make sure that the

bus connector between the CPU/IM and CP 343-1 is present).

S Attach the CP 343-1 to Industrial Ethernet as illustrated in Section 2.3.

S Connect a 24 V power supply.

Note

Make sure that you use the same voltage source as for the CPU or

IM 361.

Note

The two front panels must be kept closed during operation. The module

must be installed so that its upper and lower ventilation slits are not

covered, allowing adequate ventilation.

Configuration

To initialize the CP 343-1 for communication services, use the configuration

tool NCM S7 for Industrial Ethernet.

PG/PC Connection

You can connect the programming device when configuring the CP as

follows:

S via MPI

S via Industrial Ethernet

If you configure the module via Industrial Ethernet, the CP 343-1 must

already have a MAC address, in other words the hardware configura-

tion of the CP 343-1 must already have been downloaded via the MPI

interface (for details of node initialization, see /8/).

Productinformation CP 343–1

C79000–Z8964–C038–05

english

2.3

Attaching the CP 343-1 to Industrial Ethernet

The CP 343-1 can be attached to Industrial Ethernet using a

S Transceiver with an AUI interface

CP 343–1

RUN

STOP

RUN

STOP

Transceiver

cable

(dropcable) 727-1

Transceiver

Figure 3 Attaching the CP 343-1 to Industrial Ethernet with AUI/Transceiver

The CP 343-1 generates and supplies the 13 V power required by the

transceiver.

S Industrial Twisted Pair attachment, for example using a Optical Switch

Module (OSM) or hub.

When using the Industrial Ethernet installation cable shown in Figure 4,

the CP 343-1 automatically switches over to Twisted Pair. Information

about the pinout can be found at the end of this section.

With Industrial Twisted Pair, cables with a length of up 100 m can be

installed between the CP and Optical Switch Module (OSM).

Productinformation CP 343–1

C79000–Z8964–C038–05

english

CP 343–1

e.g Optical Switch Modul

(OSM)

RUN

STOP

RUN

STOP

RUN

STOP

ITP installation

cable

Figure 4 Attaching the CP343-1 to Industrial Ethernet with TP/Optical Switch Module (OSM) or Hub

S Optical Industrial Ethernet using an AUI attachment

Connection of the CP 343-1 TCP to Industrial Ethernet is also possible

using an optical transceiver with an AUI interface.

Optical

module

CP 343–1

RUN

STOP

Star

RUN

STOP

coupler

727-1

Fiber optic cable

Connectingcable

Figure 5 Attaching the CP 343-1 to Industrial Ethernet with AUI/ Optical Transceiver

Productinformation CP 343–1

C79000–Z8964–C038–05

english

Technical Data

3.1

General Technical Data

Dimensions and Weight

Dimensions, module in casing H x W x D (mm)

Weight

125x80x120

approx. 750 g

Voltage, Current, Operating Conditions

Power supply

5 V DC +/– 5%

24 V DC +/– 5%

Current consumption:

– from the S7-300 backplane bus:

– from the external 24 V supply:

70 mA

0.6 A.

Permitted ambient temperature

Specifications according to /7/ must be

adhered to when operating an S7-300 tier

– horizontal installation

– vertical installation

0 to 60° C

0 to 40° C

Altitude

up to 3000m above sea level

All the information in /7/ in the Section ”General Technical Data” regarding the

following topics also applies to the CP 343-1:

S Electromagnetic compatibility

S Transportation and storage conditions

S Mechanical and climatic ambient conditions

S Insulation tests, class of protection and degree of protection

Product information CP 343–1

C79000–Z8964–C038–05

english

3.2

Pinout

Connector for Industrial Ethernet

On the front panel of the CP 343-1, there is a 15-pin sub D female connector

with a sliding locking mechanism for connecting a transceiver cable. The

signals of an ITP interface can also be applied to this connector (switchover

by relay).

For operation via the AUI interface, use the 727-1 transceiver cable. A

special SIMATIC NET ITP cable must be used when operating via the ITP

interface.

Pin– No

Signal–name

Function

External ground, shield

Collision +

MEXT

CLSN

TRMT / TPETXD

Transmit + / TPE transmit

data +

Ground

Ground 5V

CP 343–1

RCV / TPERXD

Receive + / TPE Receive

data +

M 15 V

Ground 15 V

AUI/ITP switchover

Ground 5 V

RUN

TPE_SEL

Ground

STOP

RUN

STOP

CLSN_N

Collision –

TRMT_N /

Transmit – / TPE Transmit

TPETXD_N

data –

Ground

Ground 5V

RCV_N /

Receive – / TPE Receive

TPERXD_N

data –

P15 V

Ground

–

+15 V

Ground 5V

Figure 6 ConnectorPinoutDiagram

Notes on the Pinout

The pinout complies with the IEEE 802.3 AUI interface.The signals TPETXD /

TPETXD_N and TPERXD / TPERXD_N implement the ITP interface.

Productinformation CP 343–1

C79000–Z8964–C038–05

english

3.3

Notes on the CE Approval of SIMATIC NET Products

Product name:

CP 343-1

Order number: 6GK7 343-1BA00-0XE0

EU Directive EMC89/336/EEC

The SIMATIC NET products listed above meet the requirements of the EU

directive 89/336/EEC ”Electromagnetic Compatibility”.

The EU conformity certificates are available for the relevant authorities accor-

ding to the EU directives and are kept at the following address:

Siemens Aktiengesellschaft, Bereich A&D

Industrielle Kommunikation

SIMATIC NET (A&D PT 2)

Postfach 4848

D–90327 Nürnberg

Germany

Area of Application

The product is designed for use in an industrial environment.

Requirements

Area of application

Industrial

Noise emission

EN 50081-2 : 1993

Noise immunity

EN 50082-2 : 1995

Directive on Machines

The product remains a component in compliance with Article 4(2) of the EU

directive on machines 89/392/EEC.

According to the directive on machines, we are obliged to point out that this

product is intended solely for installation in a machine. Before the final pro-

duct is started up, it must be established that it conforms to the directive

89/392EEC.

Installation Guidelines

The product meets the requirements providing you adhere to the guidelines

for installation and operation in the following documentation /7/, /9/ and /12/.

Productinformation CP 343–1

C79000–Z8964–C038–05

english

References

The following documentation is necessary for configuration and operation

and contains detailed information:

/7/

/8/

For installing and starting up the CP 343-1

Manual: S7-300 Programmable Controller, Hardware and Installation

For using and configuring the CP 343-1

Manual: SIMATIC NET NCM for S7 Industrial Ethernet

/9/

SIMATIC NET Manual: Triaxial Networks for Industrial Ethernet

Ethernet Manual (HIR)

/10/

/11/

User’s Guide to STEP 7

Part of the basic STEP 7 package.

/12/

SIMATIC NET Manual: ITP Networks for Industrial Ethernet

Order Numbers

The order numbers for the SIEMENS documentation listed above can be

found in the catalogs “SIMATIC NET Industrial Communication, Catalog IK

10” and “SIMATIC Programmable Logic Controllers SIMATIC S7 / M7 / C7”.

These catalogs and additional information about the products and training

courses can be obtained from your local SIEMENS office.

Productinformation CP 343–1

C79000–Z8964–C038–05

From

C79000-Z8974-C43-01

Mail / FAX Reply (Call ++911-978-3321)

Name

.............................................................................

Position

Company

Address

Town

Siemens AG, Infoservice

A&D Z 032

Postfach 2348

D-90713 Fürth

Germany

Postcode

Country

Dear customer,

You can order a sticker to mark the actual version

level of your CP`s with this letter or by fax.

! Please send me the sticker

---

Our Industrial Ethernet application:...................................................................................................................

Type of application

Which S7-300 CPU

are you using ?

CPU 312 IFM

CPU 315

CPU 313

CPU 314 / 314 IFM

CPU 315-2

andere :............

How many CP 343-1 modules are

you using ?

No. of CP 343-1:

.............. No. of CP 443-1:

..............

No. of S5 CPs: ..............

Which and how many

Send/Receive: ! SIMATIC S5............... ! SIMATIC S7................

communication partners are you

using in your system?

! PC with CP 1413.......... ! PC with SOFTNET........

! WS.............................

S7-Functions: ! SIMATIC S7............... ! PC with CP 1413...........

! PC with SOFTNET....... ! WS..............................

Number of connections ?

SEND/RECV : ...........................

SEND/RECV :............................

S7-Functions: .............................

S7-Functions:..............................

Average data length in bytes per

connection ?

---

Type of cabling

Electrical with ITP

Optical with OLM

other:

...............................................

Electrical with

Triax (Yellow

Cable)

Optical with star

couplers

Network topology

Bus

Redund. ring

Star

other : _{................}

Suggestions:...........................................................................................................................................................

................................................................................................................................................................................

Note: Your information will be used to improve our products and will of course be handled confidentially.

Suggestions for improvement are welcome on e-mail address [email protected]. Please include for

identification “CP 343-1”.

Yorkville Sound Car Speaker YS1098 User Manual
Toshiba HDD2136 User Manual
Toshiba Full Color Led Display System TR 2010E User Manual
Sony WM EC1 User Manual
Sony VCT HM1 User Manual
Sony TRV78 User Manual
Sony ISSUE 3 User Manual
Sony Handycam HDR CX700VE User Manual
Sony CCD TR3400 User Manual
Sanyo LNS S02Z User Manual