Sharp Blu ray Player BD AMS20U User Manual

MODEL  
BD-AMS10U  
BD-AMS20U  
BLU-RAY DISC/DVD PLAYER  
OPERATION MANUAL  
BD-AMS20U only  
BD-AMS20U only  
OPERATION MANUAL  
ENGLISH  
Introduction  
SAFETY INFORMATION  
CAUTION:  
“WARNING–FCC Regulations state that  
USE OF CONTROLS OR ADJUSTMENTS OR  
PERFORMANCE OF PROCEDURES OTHER THAN  
THOSE SPECIFIED HEREIN MAY RESULT IN  
HAZARDOUS RADIATION EXPOSURE.  
CAUTION  
RISK OF ELECTRIC  
any unauthorized changes or  
modifications to this equipment not  
expressly approved by the manufacturer  
could void the user’s authority to operate  
this equipment.”  
SHOCKDO NOT OPEN  
CAUTION:  
AS THE LASER BEAM USED IN THIS UNIT IS  
HARMFUL TO THE EYES, DO NOT ATTEMPT TO  
DISASSEMBLE THE CABINET.  
TO REDUCE THE RISK OF ELECTRIC SHOCK,  
DO NOT REMOVE COVER. NO  
USER-SERVICEABLE PARTS INSIDE. REFER  
SERVICING TO QUALIFIED SERVICE  
PERSONNEL.  
This equipment has been tested and found to  
comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These  
limits are designed to provide reasonable  
protection against harmful interference in a  
residential installation. This equipment generates,  
uses and can radiate radio frequency energy and,  
if not installed and used in accordance with the  
instructions, may cause harmful interference to  
radio communications. However, there is no  
guarantee that interference will not occur in a  
particular installation. If this equipment does  
cause harmful interference to radio or television  
reception, which can be determined by turning  
the equipment off and on, the user is encouraged  
to try to correct the interference by one or more  
of the following measures:  
REFER SERVICING TO QUALIFIED PERSONNEL  
ONLY.  
This symbol warns the user of  
uninsulated voltage within the unit  
that can cause dangerous electric  
shocks.  
This symbol alerts the user that there  
are important operating and  
maintenance instructions in the  
literature accompanying this unit.  
This Player is classified as a CLASS 1 LASER  
product.  
The CLASS 1 LASER PRODUCT label is located  
on the rear cover.  
This product contains a low power laser device. To  
ensure continued safety do not remove any cover  
or attempt to gain access to the inside of the  
product. Refer all servicing to qualified personnel.  
WARNING:  
TO REDUCE THE RISK OF FIRE OR  
ELECTRIC SHOCK, DO NOT EXPOSE THIS  
APPLIANCE TO RAIN OR MOISTURE.  
–Reorient or relocate the receiving antenna.  
–Increase the separation between the equipment  
and receiver.  
–Connect the equipment into an outlet on a circuit  
different from that to which the receiver is  
connected.  
–Consult the dealer or an experienced radio/TV  
technician for help.  
1
 
SAFETY INFORMATION  
The following statement applies to BD-AMS20U only.  
*
FCC Compliance Statement  
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired  
operation.  
Wireless Radio  
For product available in the USA/Canada market, only channel 1–11 can be operated. Selection of other channels is not possible.  
This device is going to be operated in 2.400–2.483GHz frequency range, it is restricted in indoor environment only.  
Important: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.  
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.  
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.  
IMPORTANT SAFETY INSTRUCTIONS  
Electricity is used to perform many useful functions, but it can also cause personal  
injuries and property damage if improperly handled. This product has been engineered  
and manufactured with the highest priority on safety. However, improper use can result  
in electric shock and/or fire. In order to prevent potential danger, please observe the  
following instructions when installing, operating and cleaning the product. To ensure  
your safety and prolong the service life of your Blu-ray Disc/DVD Player, please read the  
following precautions carefully before using the product.  
1) Read these instructions.  
2) Keep these instructions.  
3) Heed all warnings.  
4) Follow all instructions.  
11) Only use attachments/accessories specified by the manufacturer.  
12) Use only with the cart, stand, tripod, bracket, or table specified by the  
manufacturer, or sold with the apparatus. When a cart is used, use caution when  
moving the cart/apparatus combination to avoid injury from tip-over.  
13) Unplug this apparatus during lightning storms or when unused for long periods of  
time.  
14) Refer all servicing to qualified service personnel. Servicing is required  
when the apparatus has been damaged in any way, such as power-  
supply cord or plug is damaged, liquid has been spilled or objects have  
fallen into the apparatus, the apparatus has been exposed to rain or  
moisture, does not operate normally, or has been dropped.  
5) Do not use this apparatus near water.  
6) Clean only with dry cloth.  
Additional Safety Information  
15) Power Sources—This product should be operated only from the type of power  
source indicated on the marking label. If you are not sure of the type of power  
supply to your home, consult your product dealer or local power company. For  
products intended to operate from battery power, or other sources, refer to the  
operating instructions.  
16) Overloading—Do not overload wall outlets, extension cords, or integral convenience  
receptacles as this can result in a risk of fire or electric shock.  
17) Object and Liquid Entry—Never push objects of any kind into this product through  
openings as they may touch dangerous voltage points or short-out parts that could  
result in a fire or electric shock. Never spill liquid of any kind on the product.  
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s  
instructions.  
8) Do not install near any heat sources such as radiators, heat registers, stoves, or  
other apparatus (including amplifiers) that produce heat.  
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A  
polarized plug has two blades with one wider than the other. A grounding type plug  
has two blades and a third grounding prong. The wide blade or the third prong are  
provided for your safety. If the provided plug does not fit into your outlet, consult an  
electrician for replacement of the obsolete outlet.  
10) Protect the power cord from being walked on or pinched particularly at plugs,  
convenience receptacles, and the point where they exit from the apparatus.  
2
IMPORTANT SAFETY INSTRUCTIONS  
18) Damage Requiring Service—Unplug this product from the wall outlet and refer  
servicing to qualified service personnel under the following conditions:  
a) When the AC cord or plug is damaged,  
19) Replacement Parts—When replacement parts are required, be sure the service  
technician has used replacement parts specified by the manufacturer or have the  
same characteristics as the original part. Unauthorized substitutions may result in  
fire, electric shock, or other hazards.  
b) If liquid has been spilled, or objects have fallen into the product,  
c) If the product has been exposed to rain or water,  
d) If the product does not operate normally by following the operating  
instructions.  
20) Safety Check—Upon completion of any service or repairs to this product, ask the  
service technician to perform safety checks to determine that the product is in  
proper operating condition.  
Adjust only those controls that are covered by the operating instructions as  
an improper adjustment of other controls may result in damage and will often  
require extensive work by a qualified technician to restore the product to its  
normal operation,  
21) The main AC plug is used as disconnect device and shall always remain readily  
operable.  
e) If the product has been dropped or damaged in any way, and  
f) When the product exhibits a distinct change in performance - this indicates a  
need for service.  
Water and Moisture—Do not use this product near  
water - for example, near a bath tub, wash bowl,  
kitchen sink, or laundry tub; in a wet basement; or  
near a swimming pool; and the like.  
Heat—The product should be situated away from  
heat sources such as radiators, heat registers, stoves,  
or other products (including amplifiers) that produce  
heat.  
Stand—Do not place the product on an unstable  
cart, stand, tripod or table. Placing the product on an  
unstable base can cause the product to fall, resulting  
in serious personal injuries as well as damage to the  
product. Use only a cart, stand, tripod, bracket or  
table recommended by the manufacturer or sold with  
the product.  
Lightning—For added protection for this product  
during a lightning storm, or when it is left unattended  
and unused for long periods of time, unplug it from  
the wall outlet. This will prevent damage to the  
product due to lightning and power-line surges.  
To prevent fire, never place any type of candle or  
flames on the top or near the product.  
Selecting the location—Select a place with no direct  
sunlight and good ventilation.  
To prevent fire or shock hazard, do not expose this  
product to dripping or splashing.  
Ventilation—The vents and other openings in the  
cabinet are designed for ventilation. Do not cover  
or block these vents and openings since insufficient  
ventilation can cause overheating and/or shorten the  
life of the product. Do not place the product on a bed,  
sofa, rug or other similar surface, since they can block  
ventilation openings. This product is not designed  
for built-in installation; do not place the product in an  
enclosed place such as a bookcase or rack, unless  
proper ventilation is provided or the manufacturer’s  
instructions are followed.  
No objects filled with liquids, such as vases, should  
be placed on the product.  
To prevent fire or shock hazard, do not place the AC  
cord under the product or other heavy items.  
3
PRECAUTIONS  
Precautions on viewing stereoscopic 3D images  
Notes on using Wireless LAN  
Do not view stereoscopic 3D images if you have a history of photosensitivity, heart  
disease or poor health. This may cause the symptoms to worsen.  
If you experience any health problems such as fatigue and discomfort while viewing  
stereoscopic 3D images, immediately discontinue viewing. Continuing viewing after  
symptoms appear may cause health risks. Take a break until the symptoms have  
completely disappeared.  
When this player is connected to a wireless LAN network, transmissions between  
the wireless LAN adapter (BD-AMS10U: VR-WL25, sold separetely/BD-AMS20U:  
supplied) and a wireless LAN compatible broadband router (commercially available)  
are carried out.  
Precautions on using Wireless LAN  
The following devices, radio stations, etc. use the same frequency bands. Do not use  
wireless LAN near them.  
Ages of 5–6 or over are recommended for viewing stereoscopic 3D images.  
Symptoms such as fatigue and discomfort are difficult to determine in young  
children, therefore they may suddenly become ill. When viewing 3D images with  
children, please watch for eye strain symptoms.  
When viewing stereoscopic 3D images, take a moderate break after watching one  
title. Viewing for extended periods may cause visual strain.  
Manufacturing/scientific/diagnostic equipment such as pacemakers, etc.  
Specified low power radio stations (radio stations that do not require a license)  
If this player is used near these devices, there is a possibility that radio wave  
interference may occur. Therefore transmission may not be possible or speed may be  
reduced.  
Mobile phones, radios, etc. use different radio frequency bands from wireless LAN,  
so there will not be any effect on the transmissions of these devices or wireless LAN  
if this player is used near them.  
However, if a wireless LAN product is placed near one of these devices, audio or  
video noise may occur due to the electromagnetic waves that emit from wireless LAN  
products.  
Radio waves will pass through the wood, glass, etc. used in standard housing,  
however they will not pass through reinforcing bars, metal, concrete, etc. Radio  
waves will not pass through walls and floors if these materials are used.  
Precautions when cleaning this product  
Turn off the main power and unplug the AC cord from the wall outlet before handling.  
To clean the outer cabinet, periodically wipe it with a soft cloth (cotton, flannel, etc.).  
For severe dirt, soak a soft cloth (cotton, flannel, etc.) in some neutral detergent  
diluted with water, wring the cloth out thoroughly, wipe off the dirt, then wipe again  
with a soft, dry cloth.  
Do not use chemicals or a chemically treated cloth for cleaning. It may damage the  
cabinet finish.  
4
DEAR SHARP CUSTOMER  
Thank you for your purchase of the SHARP Blu-ray Disc/DVD Player. To ensure safety and many years of trouble-free operation of your product, please read  
the Important Safety Instructions carefully before using this product.  
Getting Started  
Step 1: Unpacking  
Step 2: Selecting equipment to connect  
Make sure the following accessories are provided with the product.  
Connection varies with the equipment used. Refer to Connection  
Turn off the devices before connecting.  
Remote control unit  
“AA” size battery (g2)  
Enjoying BD-LIVE and video on demand services (e-Contents)  
To enjoy BD-LIVE content or video on demand streaming content on your TV,  
after an Internet connection is made, communication setup is required.  
Step 3: Playing back video/picture/music content  
Play back video, picture or music content from the desired media source  
such as Blu-ray and DVD discs, or via the Internet.  
Wireless LAN adapter  
(supplied with BD-AMS20U only)  
Step 4: Adjust settings to suit your preference  
Adjust settings to enjoy various features and other functions for playing  
discs/content.  
VR-WL25  
5
 
Contents  
Language Setting ....................................................................................................... 23  
Operating a SHARP TV Using the Remote Control.................................................... 23  
Turning Off or Dimming the LED Light and Indications.............................................. 23  
Using AQUOS LINK.................................................................................................... 24  
Using 3D..................................................................................................................... 24  
Control Panel.............................................................................................................. 25  
Video/Picture/Music Playback.........................................................................26  
Loading a Disc............................................................................................................ 26  
BD/DVD Video Playback............................................................................................. 26  
Displaying the disc information.............................................................................. 27  
BD/DVD Menus .......................................................................................................... 27  
Start playback by selecting a title from the top menu ........................................... 27  
Using the disc menu .............................................................................................. 27  
Using the pop-up menu......................................................................................... 28  
Enjoying BONUSVIEW or BD-LIVE............................................................................. 28  
Use of Picture in Picture function (secondary audio/video playback) ................... 29  
Virtual Package ...................................................................................................... 29  
BD-LIVE ................................................................................................................. 29  
DVD-R/-RW (VR format) / BD-RE/-R (BDAV format) Playback................................... 30  
Playback by selecting a title .................................................................................. 30  
Playback by selecting a chapter............................................................................ 31  
Sorting the titles..................................................................................................... 31  
Playback by selecting a Playlist............................................................................. 31  
Playback from the beginning or resume playback................................................. 31  
Playback using a USB device..................................................................................... 32  
Searching/sorting the titles ................................................................................... 32  
Selecting/deleting files........................................................................................... 33  
Copying files/folders .............................................................................................. 33  
Audio CD Playback..................................................................................................... 34  
Playback from the beginning ................................................................................. 34  
Playback by selecting a track ................................................................................ 34  
Operation procedure for the “Functions” menu..................................................... 34  
Audio Data (MP3 File) Playback ................................................................................. 35  
Displaying Still Images (JPEG files)............................................................................ 36  
Accessing DLNA servers............................................................................................ 37  
Playback by selecting a file list.............................................................................. 37  
Playback Functions...........................................................................................38  
Fast Forward/Reverse (Search) .................................................................................. 38  
Skipping to the Next or the Start of the Current Chapter (Track/Title) ....................... 38  
Pause/Frame Advance Playback................................................................................ 38  
Slow Playback (Forward/Reverse).............................................................................. 38  
Repeat Playback of a Title or Chapter (Repeat Playback) ......................................... 39  
Partial Repeat Playback (Repeat Playback of a Specified Part)................................. 39  
Displaying the Audio Information ............................................................................... 40  
Switching Subtitles..................................................................................................... 40  
Switching the Angle.................................................................................................... 40  
Displaying the Angle Mark.......................................................................................... 40  
Settings During Playback .................................................................................41  
Function Control......................................................................................................... 41  
Function control operation procedure ................................................................... 41  
Introduction  
SAFETY INFORMATION ......................................................................................1  
IMPORTANT SAFETY INSTRUCTIONS..............................................................2  
PRECAUTIONS ....................................................................................................4  
DEAR SHARP CUSTOMER .................................................................................5  
Getting Started ....................................................................................................5  
Contents...............................................................................................................6  
What would you like to do with this Player?.....................................................8  
About Media Types..............................................................................................9  
Blu-ray Disc.................................................................................................................. 9  
Types of Discs/Media Formats that Can Be Used with This Player ............................. 9  
Discs that Cannot Be Used with This Player.............................................................. 10  
About Disc Contents .................................................................................................. 11  
BD Video ................................................................................................................ 11  
Title, Chapter and Track......................................................................................... 11  
Icons Used on BD/DVD Video Disc Cases ............................................................ 12  
The Icons Used in This Operation Manual ................................................................. 12  
Important Information.......................................................................................13  
Disc Precautions......................................................................................................... 13  
License and Copyright ............................................................................................... 13  
Major Components............................................................................................14  
Main Unit (Front)......................................................................................................... 14  
Main Unit (Rear).......................................................................................................... 14  
Remote Control Unit................................................................................................... 15  
Keylock function......................................................................................................... 15  
Connection  
Connecting to a TV/projector...........................................................................16  
Connecting to an amplifier/AV receiver ..........................................................17  
HDMI connection........................................................................................................ 17  
Digital audio connection............................................................................................. 17  
Connecting to a USB device.............................................................................18  
Broadband Internet Connection ......................................................................19  
Wired connection (LAN cable).................................................................................... 19  
Wireless connection (wireless LAN)............................................................................ 20  
Playback  
Before Starting Playback..................................................................................21  
Loading the Batteries in the Remote Control............................................................. 21  
Approximate operating range of remote control.................................................... 21  
Connecting the Power Cord....................................................................................... 21  
Turning the Power On................................................................................................. 22  
Turning the power on ............................................................................................. 22  
Entering standby.................................................................................................... 22  
Indicators on the Player ......................................................................................... 22  
About the Home screen......................................................................................... 22  
6
Contents  
Functions which can be set ................................................................................... 42  
Enjoying smartphone on the TV (for BD-AMS20U only) ................................43  
What to do first:  
player.  
Settings  
SETTINGS...........................................................................................................44  
Common operations................................................................................................... 44  
Basic Operation for Playback Setting ........................................................................ 45  
Audio Video Settings .................................................................................................. 46  
Smart Settings............................................................................................................ 47  
Playback Setting......................................................................................................... 48  
System........................................................................................................................ 49  
Communication Setup................................................................................................ 50  
Sets whether “Cable” or “Wireless” is used for the network connection .............. 50  
When selecting Cable ............................................................................................ 50  
When selecting Wireless........................................................................................ 51  
The operation procedure for inputting characters manually.................................. 53  
USB (HDD/Memory) Management ............................................................................. 54  
Software Update Settings .......................................................................................... 55  
Auto Update from Network.................................................................................... 55  
Manual Update from Network................................................................................ 56  
Manual Update from USB memory device ............................................................ 56  
Explains the important operation information.  
Shows the connecting options provided by this Player.  
Shows simple playback and useful functions.  
Streaming content  
Playing back video on demand streaming content........................................59  
Instantly Watching Movies from Netflix...................................................................... 59  
Enjoying Movies and Internet Application with VUDU ............................................... 60  
Playing back YouTube content ................................................................................... 61  
Gives you more options to suit your circumstances.  
Appendix  
PC control of the Player (for BD-AMS20U only) .............................................62  
Troubleshooting.................................................................................................64  
To Reset this Player................................................................................................ 67  
On-screen Error Messages ..............................................................................68  
Specifications ....................................................................................................69  
Glossary .............................................................................................................71  
Network Service Disclaimer.............................................................................74  
About Software License....................................................................................75  
LIMITED WARRANTY........................................................................................76  
Shows the Internet streaming services available with this  
player.  
Provides troubleshooting tips and more information.  
The illustrations and on-screen displays in this operation manual  
are for explanation purposes and may vary slightly from the  
actual operations.  
NOTE  
The illustrations used throughout this operation manual are based on BD-AMS20U.  
7
What would you like to do with this Player?  
Watch high quality movies on Blu-ray discs  
Enjoy BD-LIVE functions through the Internet  
This Player is compatible with BD-LIVE. You can enjoy bonus content such  
as movie trailers through the Internet when playing back BD-Video discs  
compatible with BD-LIVE.  
This Player offers full high-definition Blu-ray disc playback.  
Enjoy stereoscopic and powerful 3D images  
This player can play 3D content from 3D compatible Blu-ray discs through  
an HDMI cable. To watch 3D images, connect a 3D compatible TV to this  
player using an HDMI cable and play the 3D content while wearing 3D  
glasses.  
Access to videos, pictures and music from home network  
servers  
This player can play back video, picture and music data stored on your  
home network servers such as a DLNA certified PC.  
Enjoy different kinds of media sources  
Use this player to enjoy video, picture or music content from various types  
of media sources such as DVDs, USB devices and via the Internet.  
Enjoy video on demand streaming content with higher  
image quality on your TV  
This player supports video on demand streaming services using the  
Internet. By connecting this player to the Internet, you can enjoy various  
content streamed on your TV. Also, with this player’s “Super Picture”  
function, you can enjoy video streaming images with higher image quality.  
Playing back video on demand streaming content (pp. 59–61)  
Simple connection and operation through HDMI  
This Player is equipped with an HDMI terminal. You can connect it to the TV  
using HDMI and no other cable will be needed to enjoy movies. If your TV is  
compatible with AQUOS LINK, you can control both the TV and this Player  
with simple operations.  
Connecting to a TV/projector (p. 16)  
8
About Media Types  
Recording  
Format  
Disc  
Size  
Media Format  
Recording Format  
Contents  
Blu-ray Disc  
Disc Type  
Contents  
USB device  
(USB HDD, USB (H.264/MKV)  
memory device)  
DivX Plus® HD  
Audio + Video  
(Movie)  
Blu-ray Disc is the ultimate next generation optical  
media format, offering the following key features:  
Largest capacity (25 GB single layer – 50 GB dual layer)  
– with over 5 times the amount of content possible with  
current DVDs, particularly well suited for high definition  
feature films with extended levels of interactive features  
Pristine picture quality with the capability for full high  
definition 1920 x 1080p resolution  
BD  
Region  
Video code A/ALL  
Audio  
+ Video  
(Movie)  
12 cm  
(5”)  
Still image  
(JPEG file)  
JPEGJ  
Audio  
MP3K  
BD-RE/BD-RE DL  
BD-R/BD-R DL  
BDMV/BDAV  
format  
See the following page for details on these terms.  
*
Best audio possible with uncompressed surround sound  
(higher quality than even theater audio)  
Broadest industry support – ensuring more choice for  
consumers in the marketplace  
Hardware products will be backward compatible with  
DVDs, allowing continued enjoyment of existing DVD  
libraries.  
Disc Durability – new breakthroughs in hard coating  
technologies gives Blu-ray Discs the strongest  
resistance to scratches and finger prints.  
BD/DVD video players and discs have region codes,  
which dictate the regions in which a disc can be played.  
This Player’s region code is A for BD and 1 for DVD.  
(Discs marked ALL will play in any player.)  
BD/DVD video operations and functions may be  
different from the explanations in this manual and  
some operations may be prohibited due to disc  
manufacturer’s settings.  
DVD Region  
Video code  
1/ALL  
Video format  
Audio  
+ Video  
(Movie)  
12 cm  
(5”)  
8 cm  
(3”)  
ALL  
1
DVD+RW/DVD+R  
DVD-RW/DVD-R  
DVD+R DL/DVD-R format  
Video/VR/  
AVCHD  
Audio  
+ Video  
(Movie)  
12 cm  
(5”)  
8 cm  
(3”)  
If a menu screen or operating instructions are displayed  
during playback of a disc, follow the operating  
procedure displayed.  
DL  
(finalized disc  
only)  
DivX Plus®  
HD  
(H.264/MKV)  
Types of Discs/Media Formats that  
Can Be Used with This Player  
NOTE  
Playback for some of the discs in the left side column  
tables may not be possible depending on the disc.  
“Finalize” refers to a recorder processing a recorded  
disc so that it will play in other DVD players/recorders  
as well as this player. Only finalized DVD discs will play  
back in this player. (This player does not have a function  
to finalize discs.)  
Regarding DVD+RW/+R/+R DL discs, only video format  
discs (finalized) can be played back. JPEG files, MP3  
files, DivX Plus® HD files, etc. cannot be played back.  
Some discs cannot be played back depending on the  
recording format.  
The following discs can be played back in this Player.  
Do not use an 8 cm (3”) to 12 cm (5”) adapter.  
Use discs that conform to compatible standards as  
indicated by the presence of official logos on the disc  
label. Playback of discs not complying with these  
standards is not guaranteed. In addition, the image  
quality or sound quality is not guaranteed even if the  
discs can be played back.  
Still  
image  
(JPEG file)  
JPEGJ  
Audio  
Audio  
MP3K  
Audio CD  
(CD-DA)  
12 cm  
(5”)  
8 cm  
(3”)  
Audio CDI  
CD-RW/CD-R  
Audio CD  
(CD-DA)  
Audio  
Still  
image  
(JPEG file)  
DivX playback may not be available depending on the  
DivX content and file.  
JPEGJ  
Audio  
MP3K  
9
                   
About Media Types  
*3 About the MP3 file format  
The following CD-RW/R discs cannot be played.  
Discs on which data has not been recorded cannot be  
played back.  
Discs recorded in a format other than an Audio CD and  
JPEG/MP3 file format cannot be played back.  
Discs may not be played back depending on their  
recording status or the status of the disc itself.  
Discs may not be played back depending on their  
compatibility with this Player.  
Discs that Cannot Be Used with  
This Player  
MP3 files are audio data compressed in the  
MPEG1/2 Audio layer-3 file format. “MP3 files” have  
“.mp3” as extensions. (Some files that have “.mp3”  
extensions or files that have not been recorded in  
MP3 format will produce noise or cannot be played.)  
The following discs cannot be played back or will  
not play back properly on this Player. If such a  
disc is mistakenly played back, speaker damage  
may occur. Never attempt to play back these  
discs.  
Playing the MP3 file format  
The MP3 files are not played in the order they were  
recorded.  
It is recommended to record data at a lower speed as  
data recorded at a fast speed can produce noise and  
may not be able to be played.  
The more folders there are, the longer the reading time.  
Depending on the folder tree, reading MP3 files can take  
time.  
*2 About the JPEG file format  
CDG, Video CD, Photo CD, CD-ROM, CD-TEXT,  
SVCD, SACD, PD, CDV, CVD, DVD-RAM, DVD-  
Audio, BD-RE with the cartridge, CD-WMA  
JPEG is a type of file format for storing still-image  
files (photos, illustrations, etc.). The Player lets you  
play JPEG format still-image files.  
File formats that are not compatible.  
Still images in formats other than JPEG (such as TIFF)  
cannot be played.  
There may be some files that cannot be played even if  
they are in JPEG format.  
Progressive JPEG files cannot be played.  
Moving image files as well as Motion JPEG format files  
cannot be played, even though they are JPEG files.  
Discs with unusual shapes cannot be played.  
Discs with unusual shapes (heart-shaped or hexagonal  
discs, etc.) cannot be used. The use of such discs will  
cause malfunction.  
The playing time may not be correctly displayed during  
MP3 file playback.  
The following files cannot be played on this  
player.  
When both Audio CD [CD-DA] format and JPEG/  
MP3 file formats are recorded on a disc. (The disc is  
recognized to be an Audio CD [CD-DA] only tracks in  
Audio CD [CD-DA] format are played back.)  
Multi-session discs cannot be played.  
The following BD video discs cannot be played.  
Discs not displaying “A” or “ALL” for the region code  
(discs sold outside the authorized marketing area).*  
Discs produced illegally.  
Discs recorded for commercial use.  
The region code for this product is A.  
Other files that cannot be played back.  
You may not be able to play some still images which  
you have created, touched up, copied or otherwise  
edited on your computer.  
You may not be able to play some still images you have  
processed (rotated or saved by overwriting other images  
you have imported from the Internet or e-mail).  
*
The following DVD video discs cannot be played.  
Discs not displaying “1” or “ALL” for the region code  
(discs sold outside the authorized marketing area).*  
Discs produced illegally.  
Discs recorded for commercial use.  
The region code for this product is 1.  
About the DivX Plus® HD (H.264/MKV)  
file format  
DivX playback may not be available depending on the  
DivX content and file.  
You may experience one or more of the following  
symptoms when playing files.  
It may take some time to play files depending on the  
number of folders, number of files and volume of data  
involved.  
EXIF information will not be displayed. EXIF stands for  
Exchangeable Image File Format, and is a standard for  
storing interchange information in image files, especially  
for more information.)  
*
The following BD-RE/R, DVD-RW/R and  
DVD+RW/R discs cannot be played.  
Discs on which data has not been recorded cannot be  
played back.  
*1 The following Audio CD discs cannot be played.  
Discs containing a signal for the purpose of protecting  
copyrights (copy control signal) may not be played back  
with this Player.  
This Player has been designed on the premise of  
playing back Audio CDs that comply with CD (Compact  
Disc) standards.  
10  
 
About Media Types  
About files/folders for Still images (JPEG  
ABOUT DivX VIDEO  
Title, Chapter and Track  
DivX® is a digital video format created by DivX, LLC, a  
subsidiary of Rovi Corporation. This is an official DivX  
Certified® device that plays DivX video. Visit divx.com  
for more information and software tools to convert your  
files into DivX videos.  
files) and audio data (MP3 files)  
You can play still images (JPEG files) /audio data  
(MP3 files) with this unit by making folder(s) on discs  
or USB devices as shown below.  
Blu-ray discs and DVDs are divided into “Titles”  
and “Chapters”. If the disc has more than one  
movie on it, each movie would be a separate  
“Title”. “Chapters”, on the other hand, are  
subdivisions of titles. (See Example 1.)  
Audio CDs are divided into “Tracks”. You can think  
of a “Track” as one tune on an Audio CD. (See  
Example 2.)  
Example of a folder structure (Disc):  
Root  
DivX Certified® to play DivX® and DivX Plus® HD  
(H.264/MKV) video up to 1080p HD including premium  
content.  
001.jpg/001.mp3  
*
xxx.jpg/xxx.mp3  
ABOUT DivX VIDEO-ON-DEMAND  
This DivX Certified® device must be registered in  
order to play purchased DivX Video-on-Demand (VOD)  
movies. To obtain your registration code, locate the DivX  
VOD section in your device setup menu. Go to vod.  
divx.com for more information on how to complete your  
registration.  
Example 1: Blu-ray disc or DVD  
*
001.jpg/001.mp3  
01 Folder  
Folder  
256.jpg/256.mp3  
Title 1  
Title 2  
001.jpg/001.mp3  
255.jpg/255.mp3  
Chapter 1  
Chapter 2  
Chapter 3  
Chapter 1  
*
*
About Disc Contents  
BD Video  
Example 2: Audio CD  
xxx Folder  
001.jpg/001.mp3  
256.jpg/256.mp3  
Track 1  
Track 2  
Track 3  
Track 4  
Enjoy BD-specific functions including BONUSVIEW  
(BD-ROM Profile 1 Version 1.1), such as picture-in-  
Including the root directory, the maximum number of folders  
and files in each folder is limited to 256 in total.  
*
File and folder requirements  
For the BD video discs compatible with  
The discs or USB devices which this player can play  
back (recognize) are limited to the following properties:  
Contains EXIF format files (only JPEG files)  
Picture resolution: Between 32 x 32 and 7680 x 4320  
pixels (only JPEG files)  
BONUSVIEW/BD-LIVE, you can enjoy additional  
contents by copying the data from the discs or  
downloading it via the Internet. For instance, this  
function is capable of playing the original movie as  
the primary video while playing video commentary  
from the film director on a small screen as a  
secondary video.  
Maximum number of folders and files in each folder:  
Disc:  
256  
USB device: 65536  
Maximum hierarchy level of folders: 5  
File size: 20 MB or less (JPEG files)  
200 MB or less (MP3 files)  
NOTE  
The available functions differ depending on the disc.  
NOTE  
File and folder names displayed on this player may differ  
from those displayed on PCs.  
11  
   
About Media Types  
2
3
4
Subtitle languages  
Icons Used on BD/DVD Video Disc  
Cases  
This indicates the kind of subtitles.  
Screen aspect ratio  
Movies are shot in a variety of screen modes.  
The back of the case of a BD/DVD that is  
commercially available usually contains various  
information about the contents of the disc.  
Camera angle  
Recorded onto some BD/DVD discs are scenes  
which have been simultaneously shot from a number  
of different angles (the same scene is shot from the  
front, from the left side, from the right side, etc.).  
1
2
1. English  
2. Chinese  
1. English  
2. Chinese  
2
5
2
Region code  
This indicates the region code (playable region code).  
3
4
5
The Icons Used in This Operation  
Manual  
1 23  
4 56  
16:9 LB  
2
.............. Indicates the functions that can be  
performed for BD Video discs.  
DVD Video BD Video  
BD VIDEO  
BD-RE  
BD-R  
1
Audio tracks and audio formats  
.............. Indicates the functions that can be  
performed for BD-RE discs.  
BD and DVD discs can contain up to 8 separate  
tracks with a different language on each. The first in  
the list is the original track.  
.............. Indicates the functions that can be  
performed for BD-R discs.  
This section also details the audio format of each  
soundtrack — Dolby Digital, DTS, MPEG etc.  
...........Indicates the functions that can be  
DVD VIDEO  
performed for DVD Video discs.  
Dolby Digital  
.............. Indicates the functions that can be  
performed for DVD-RW discs.  
A sound system developed by Dolby Laboratories Inc.  
that gives movie theater ambience to audio output  
when the Player is connected to a Dolby Digital  
processor or amplifier.  
DVD-RW  
DVD-R  
AUDIO CD  
CD-R  
.............. Indicates the functions that can be  
performed for DVD-R discs.  
DTS  
.............. Indicates the functions that can be  
performed for Audio CDs.  
DTS is a digital sound system developed by DTS, Inc.  
for use in cinemas.  
.............. Indicates the functions that can be  
performed for CD-R discs.  
Linear PCM  
Linear PCM is a signal recording format used for  
Audio CDs and on some DVD and Blu-ray discs. The  
sound on Audio CDs is recorded at 44.1 kHz with  
16 bits. (Sound is recorded between 48 kHz with 16  
bits and 96 kHz with 24 bits on DVD video discs and  
between 48 kHz with 16 bits and 192 kHz with 24 bits  
on BD video discs.)  
.............. Indicates the functions that can be  
performed for CD-RW discs.  
CD-RW  
USB  
.............. Indicates the functions that can be  
performed for USB devices.  
12  
 
Important Information  
HDMI, the HDMI logo and High-Definition Multimedia  
Interface are trademarks or registered trademarks of  
HDMI Licensing LLC.  
“x.v.Color” and “x.v.Color” logo are trademarks of Sony  
Corporation.  
Java is a registered trademark of Oracle and/or its  
affiliates.  
“BONUSVIEW” logo is a trademark of Blu-ray Disc  
Association.  
“AVCHD” and the “AVCHD” logo are trademarks of  
Panasonic Corporation and Sony Corporation.  
“Blu-ray 3D” and “Blu-ray 3D” logo are trademarks of  
Blu-ray Disc Association.  
Netflix and the Netflix logo are the registered trademarks  
of Netflix, Inc.  
YouTube is a trademark of Google Inc.  
VUDU™ is a trademark of VUDU, Inc.  
DivX®, DivX Certified®, DivX Plus® HD and associated  
logos are trademarks of Rovi Corporation or its  
subsidiaries and are used under license.  
LC_LCFONT+ and LC logo  
mark are registered trademarks of SHARP Corporation.  
This product is embedded with LC Font technology,  
which was developed by SHARP Corporation for clearly  
displaying easy-to-read characters on an LCD screen.  
However, other non-LCD fonts are used for displaying  
some screen pages.  
Cleaning the Pick Up Lens  
Disc Precautions  
Never use commercially available cleaning discs. The  
use of these discs can damage the lens.  
Request the nearest service center approved by SHARP  
to clean the lens.  
Be Careful of Scratches and Dust  
BD, DVD and CD discs are sensitive to dust, fingerprints  
and especially scratches. A scratched disc may not  
be able to be played back. Handle discs with care and  
store them in a safe place.  
Warnings about dew formation  
Condensation may form on pick up lens or disc in the  
following conditions:  
Immediately after a heater has been turned on.  
In a steamy or very humid room.  
When the Player is suddenly moved from a cold  
environment to a warm one.  
When condensation forms:  
Proper Disc Storage  
Place the disc in the center  
of the disc case and store the  
case and disc upright.  
It becomes difficult for the Player to read the signals  
on the disc and prevents the Player from operating  
properly.  
Avoid storing discs in locations  
subject to direct sunlight,  
close to heating appliances or  
in locations of high humidity.  
To remove condensation:  
Take out the disc and leave the Player with the  
power off until the condensation disappears. Using  
the Player when there is condensation may cause  
malfunction.  
Do not drop discs or subject  
them to strong vibrations or  
impacts.  
License and Copyright  
Avoid storing discs in locations  
where there are large amounts  
of dust or moisture.  
Audio-visual material may consist of copyrighted  
works which must not be recorded without the  
authority of the owner of the copyright. Refer to  
relevant laws in your country.  
“This item incorporates copy protection technology  
that is protected by U.S. patents and other intellectual  
property rights of Rovi Corporation. Reverse engineering  
and disassembly are prohibited.”  
MHL, the MHL logo, and Mobile High-Definition Link are  
trademarks or registered trademarks of MHL licensing,  
LLC.  
“Copyright 2004-2010 Verance Corporation. Cinavia™  
is a Verance Corporation trademark. Protected by U.S.  
Patent 7,369,677 and worldwide patents issued and  
pending under license from Verance Corporation. All  
rights reserved.”  
Handling Precautions  
If the surface is soiled, wipe gently with a soft, damp  
(water only) cloth. When wiping discs, always move the  
cloth from the center hole toward the outer edge.  
Manufactured under license from Dolby Laboratories.  
“Dolby” and the double-D symbol are trademarks of  
Dolby Laboratories.  
ENERGY STAR® Program Information  
Manufactured under license under U.S. Patent #’s:  
5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616;  
6,487,535; 7,392,195; 7,272,567; 7,333,929; 7,212,872  
& other U.S. and worldwide patents issued & pending.  
DTS and the Symbol are registered trademarks, &  
DTS-HD, DTS-HD Master Audio | Essential and the DTS  
logos are trademarks of DTS, Inc. Product includes  
software. ©DTS, Inc. All Rights Reserved.  
Do not use record cleaning sprays, benzene, thinner,  
static electricity prevention liquids or any other solvent.  
Do not touch the surface.  
Do not stick paper or adhesive labels to the disc.  
If the playing surface of a disc is soiled or scratched,  
the Player may decide that the disc is incompatible  
and eject the disc tray, or it may fail to play the disc  
correctly. Wipe any dirt off the playing surface with a  
soft cloth.  
Products that have earned  
the ENERGY STAR® are  
designed to protect the  
environment through  
superior energy efficiency.  
is a trademark.  
“BD-LIVE” logo is a trademark of Blu-ray Disc  
Association.  
is a trademark of DVD Format/Logo Licensing  
Corporation.  
ENERGY STAR® is a U.S. registered mark.  
13  
       
Major Components  
Main Unit (Front)  
Main Unit (Rear)  
1
*
2
3
4
5
6
2
3
4
5
6
1
1
7
8 9  
10  
1
8 Remote control sensor (p. 21)  
1
3
4
2 MHL/HDMI INPUT terminal (p. 43) ( 1 for BD-AMS20U only)  
*
The elapsed time is displayed during  
playback.  
When skipping is performed,  
the chapter (or track) number is  
displayed.  
J
6
2
*
POWER (ON/STANDBY) indicator (p. 22  
)
7
Only use the recommended wireless LAN adapter (VR-WL25, supplied with BD-AMS20U only)  
with this player.  
NOTE  
When you insert or remove a USB device, be sure to turn off the main power of this  
player and the USB device (only if connecting a USB HDD). Also, be sure to set “Quick  
Start” to “No” (See page 47) before inserting or removing the device. If you insert or  
remove the device with the player or Quick Start on, the data may become damaged.  
14  
Major Components  
Remote Control Unit  
1
2
1
2
3
16  
17  
6
7
8
9
This function is available for BD-AMS20U only.  
4
Q Cursor buttons (a/b/c/d), ENTER (pp. 23, 44)  
E A (Red), B (Green), C (Blue), D (Yellow)  
5
6
18  
19  
20  
21  
R
(Lock) (See below.)  
7
8
9
10  
22  
Keylock function  
11  
You can set the keylock to prevent accidental operations.  
This function allows TVs compatible with AQUOS LINK to also perform a Key Lock on the player.  
Press and hold  
(Lock) for more than 3 seconds.  
12  
13  
23  
Each time you perform this operation, the function is activated or deactivated.  
If you try to operate the Player while the keylock function is set, “Hold” blinks on the front display panel  
to indicate that the keylock function is set.  
14  
15  
24  
25  
15  
 
Connection  
Connecting to a TV/projector  
You can enjoy high quality digital picture and sound using an HDMI cable. (Only  
TVs/projectors with an HDMI terminal can be connected to this player.)  
When you use AQUOS LINK, make sure to use a certified HDMI cable.  
NOTE  
In this player, HDMI Video Out” is set to “Auto” as a default (See page 46). (Normally set  
to “Auto”.) If you don’t get a stable image with “HDMI Video Out” set to “Auto”, select  
the output resolution which corresponds to the connected equipment.  
To enjoy 3D images, connection to a 3D compatible TV is needed.  
For connection to a TV/projector, refer to the TV/projector’s operation manual.  
1 Be sure to turn off this Player and the TV/projector before making any  
connections.  
2 Firmly connect an HDMI cable (commercially available) to the HDMI OUT  
terminal on the player (1) and the HDMI IN terminal of the TV/projector (2).  
E
After connecting  
If necessary, perform the Audio Video Settings. (Pages 46–47)  
HDMI cable  
(commercially available)  
Projector  
TV  
16  
   
Connecting to an amplifier/AV receiver  
You can connect this player to an amplifier/AV receiver to enjoy digital surround  
sound. With this player, the audio connection can be made using either one of  
the following methods depending on the capabilities of the amplifier/AV receiver  
you connect.  
NOTE  
When using an HDMI output, 7.1 ch Digital Output is available.  
Audio transmitted in DTS-HD High Resolution Audio and DTS-HD Master Audio  
formats is output from the HDMI terminal as Bitstream. Connect an amplifier with a  
built-in decoder to enjoy the fine sound quality.  
When a connection to a 3D TV is made via an amplifier/AV receiver, it is necessary to  
connect to a 3D compatible amplifier/AV receiver.  
If the amplifier/AV receiver is not 3D compatible, connect the HDMI cable to the TV  
directly while connecting the player and the amplifier/AV receiver using an optical  
digital cable.  
HDMI connection  
Digital audio connection  
NOTE  
Be sure to turn off this Player and the equipment before making any connections.  
HDMI connection  
Digital audio connection  
You can connect an amplifier/AV receiver using an optical digital audio cable  
(commercially available).  
HDMI cable  
*
Optical digital  
cable  
*
Amplifier/  
AV receiver  
Commercially available  
*
TV  
Amplifier/  
AV receiver  
HDMI cable  
*
NOTE  
Commercially available  
*
When using OPTICAL DIGITAL AUDIO OUT, 5.1ch Digital Output is available. (7.1ch  
Digital Output is not available.)  
E
After connecting  
If necessary, perform the Audio Video Settings. (Pages 46–47)  
17  
   
Connecting to a USB device  
You can connect USB devices to this player (USB memory device, USB HDD) to  
enjoy video, music, or picture files stored on the USB device. This player has 2  
USB terminals, one on the front side and another on the rear side.  
1 Connect a USB cable (commercially available) to the USB1 or USB2 terminal  
on this player and the USB port of the USB HDD.  
2 Turn on the power of the USB HDD.  
NOTE  
3 Press POWER to turn on the power of this player.  
When you insert or remove a USB device, be sure to turn off the main power of this  
player and the USB device (only if connecting a USB HDD). Also, be sure to set “Quick  
Start” to “No” (See page 47) before inserting or removing the device. If you insert or  
remove the device with the player or Quick Start on, the data may become damaged.  
Refer to “Wireless connection (wireless LAN)” on page 20 when connecting a wireless  
LAN adapter.  
CAUTION  
SHARP cannot guarantee breakdown or malfunction of a USB HDD, or loss of the  
stored data in a USB HDD caused by connecting to other equipment.  
NOTE  
Make sure to use a USB device supporting USB 2.0 High Speed (480 Mbps).  
Only self-powered type USB HDD can be used with this player. USB-powered HDD  
cannot be used.  
USB memory device connection  
Refer to the operation manual for the USB HDD for details regarding usage.  
This player cannot play back TV programs recorded in a USB HDD by a recorder.  
Example: Front*  
Regarding USB HDD formats  
USB HDD is compatible with the following formats:  
USB memory  
device  
Formats  
USB2 terminal  
A USB terminal is also available on the rear side (USB1 terminal).  
FAT32  
4
NTFS  
4
EXT3  
4
*
Format  
Copy  
USB HDD connection  
4
Delete  
Play  
4
4
4
Example: Front*  
4
4
4
E
After connecting  
Toplaybackvideo, musicorpicturefilesstoredinaUSBdevice, seepages32–33  
USB cable  
(commercially available)  
USB  
USB HDD  
A USB terminal is also available on the rear side (USB1 terminal).  
*
18  
   
Broadband Internet Connection  
By connecting this player to the Internet, you can enjoy a variety of content  
on your TV using BD-LIVE functions, video on-demand services (e-Contents),  
home networks and also perform software updates. In this player, the Internet  
connection can be made using either one of the following methods.  
Wired connection (LAN cable)  
Wired connection (LAN cable)  
Connect a LAN cable (commercially available) to the ETHERNET terminal of this  
player (1) and the LAN port of the broadband router (2).  
Wireless connection (wireless LAN) (See page 20.)  
NOTE  
Be sure to turn off this Player and the equipment before making any connections.  
When an Internet connection is made, wired and wireless connections cannot be used  
at the same time. Use only one of the connection types (See page 50).  
CAUTION  
When using a broadband Internet connection, a contract with an Internet service  
provider is required. For more details, contact your nearest Internet service provider.  
Refer to the operation manual of the equipment you have as the connected equipment  
and connection method may differ depending on your Internet environment.  
LAN cable  
*
PC  
LAN  
Internet  
Modem  
Broadband  
router  
Commercially available  
*
NOTE  
Use a LAN cable/router supporting 10BASE-T/100BASE-TX.  
SHARP cannot guarantee that all brands’ broadband routers will operate with this  
player.  
E
After connecting  
To update the software via the Internet, perform Software Update Settings.  
19  
 
Broadband Internet Connection  
NOTE  
Wireless connection (wireless LAN)  
When you insert or remove a wireless LAN adapter, be sure to turn the main power off  
You must use a wireless router/access point that supports IEEE802.11 b/g/n. (n is  
recommended for stable operation of the wireless network.)  
Insert a wireless LAN adapter (Model number VR-WL25, supplied with BD-  
AMS20U only) into the W-LAN/USB1 terminal on the rear of the player.  
Wireless LAN, in its nature, may cause interference, depending on the usage conditions  
(access point performance, distance, obstacles, interference by other radio devices,  
etc.).  
Set the wireless router/access point to Infrastructure mode. Ad-hoc mode is not  
supported.  
SHARP cannot guarantee that wireless LAN adapters other than the VR-WL25 adapter  
(supplied with BD-AMS20U only) will operate with this player.  
SHARP cannot guarantee that all brands’ wireless routers will operate with this player.  
E
After connecting  
To update the software via the Internet, perform Software Update Settings.  
Wireless LAN  
adapter  
(supplied with  
*
BD-AMS20U only)  
PC  
Wireless  
router  
Modem  
Internet  
When a wireless connection is made, it is necessary to enter the MAC address  
shown on the wireless LAN adapter for the wireless router. We recommend writing  
Optional accessories*  
Wireless LAN adapter  
(supplied with BD-AMS20U only)  
VR-WL25  
20  
 
Playback  
Before Starting Playback  
NOTE  
Loading the Batteries in the Remote  
Control  
Connecting the Power Cord  
Do not subject the remote control unit to shock, water  
or excessive humidity.  
The remote control unit may not function if the Player’s  
remote sensor is in direct sunlight or any other strong  
light.  
Plug the AC cord into AC outlet.  
1 Hold in the tab on the battery cover and pull the  
cover towards the direction of the arrow.  
Incorrect use of batteries may cause them to leak or  
burst. Read the battery warnings and use the batteries  
properly.  
Do not mix old and new batteries, or mix different  
brands.  
Remove the batteries if you will not use the remote  
control unit for an extended period of time.  
2 Load the two “AA” size batteries (R-06 size,  
UM/SUM-3). Place batteries with their terminals  
corresponding to the m and n indications in  
battery compartment.  
Approximate operating range of  
remote control  
NOTE  
Place the Player close to the AC outlet, and keep the  
power plug within reach.  
Remote control sensor  
TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT  
TOUCH THE UN-INSULATED PARTS OF ANY CABLES  
WHILE THE AC CORD IS CONNECTED.  
The POWER (ON/STANDBY) indicator blinks while the  
Player is preparing for starting up. You cannot turn the  
Player on until the POWER (ON/STANDBY) indicator  
stops blinking.  
If you are not going to use this Player for a long period  
of time, be sure to remove the AC cord from the AC  
outlet.  
3 Insert the smaller tab of the battery cover into  
the opening 1, and press down on the cover  
until it clicks in place 2.  
*Approx. 22 feet (7m)  
15º  
30º  
30º  
15º  
WARNING  
Do not use or store batteries in direct sunlight or other  
excessively hot place, such as inside a car or near a  
heater.  
This can cause batteries to leak, overheat, explode or  
catch fire.  
Remote control unit  
It can also reduce the life or performance of batteries.  
21  
       
Before Starting Playback  
Turning the Power On  
Turning the power on  
Indicators on the Player  
Press POWER on the remote control or on the  
Player to turn on the power of the Player.  
POWER (ON/STANDBY) indicator  
Green on  
Red on  
Power on  
Standby  
BD/DVD/CD mode indicator  
NOTE  
Blue on  
Playing back  
Loading a disc/updating  
1
2
When you turn on this player for the first time after  
purchase or when you turn on this player after you  
setting screen will be displayed, so please perform the  
Blue blinks  
About the Home screen  
When turning on the player, the Home screen  
appears.  
Entering standby  
Home screen  
3
4
Press POWER on the remote control or on the  
Player to enter standby.  
1 POWER button  
Video  
Music  
Picture  
e-Contents  
Settings  
2 POWER (ON/STANDBY) indicator  
3 BD/DVD/CD mode indicator  
4 Front panel display  
If you press POWER again immediately after entering  
standby, the Player may not turn on. If this happens,  
wait for 10 seconds or more and then turn on the power  
again.  
BD-VIDEO  
USB-1  
USB-2  
Home Network  
Next  
NOTE  
1 Main menu  
2 Submenu  
3 Button Guide  
When the POWER (ON/STANDBY) indicator is blinking  
(may take some time), the Player cannot be turned on.  
22  
 
Before Starting Playback  
Language Setting  
Operating a SHARP TV Using the  
Remote Control  
Turning Off or Dimming the LED  
Light and Indications  
The Universal Remote Control may operate the  
basic functions of the SHARP TV.  
If you feel that the indicators on the player’s front  
display are too bright when watching movies, you  
can turn them off except for the POWER (ON/  
STANDBY) indicator.  
You can also adjust the brightness of the front  
display/LED light by selecting “Dimmer”.  
TV function control  
TV Power: POWER  
TV-AV Selector: INPUT  
TV Volume up/down: VOL e/f  
TV Channel up/down: CH r/s  
Changing the on-screen display  
language  
1 Press c/d to select “Settings”, then press b or  
ENTER.  
2 Press c/d to select “System”, then press b or  
ENTER.  
3 Press a/b to select “On Screen Language”,  
then press d or ENTER.  
1 Press c/d to select “Settings”, then press b or  
4 Press a/b to select the language you want to  
ENTER.  
display on the screen, then press ENTER.  
2 Press c/d to select “Smart Settings”, then  
press b or ENTER.  
NOTE  
3 Press a/b to select “Front Display/LED”, then  
To select the DVD disc language, such as subtitle  
press d or ENTER.  
4 Press a/b to select “On”, “Dimmer” or “Off”,  
then press ENTER.  
5 Press HOME or EXIT to exit.  
NOTE  
When “Dimmer” is selected, the BD/DVD/CD mode  
indicator turns off.  
23  
       
Before Starting Playback  
Using AQUOS LINK  
E
AQUOS PURE MODE  
NOTE  
When you connect this player to an AQUOS LCD  
TV compatible with AQUOS LINK and set “AQUOS  
adjusted to the most suitable image quality for the  
AQUOS TV are output from the HDMI OUT terminal  
of this player.  
The 3D mode can be switched only when playback is  
stopped.  
Depending on the connected TV, the images during  
playback may switch to 2D images due to changes in  
the resolution, etc. Make sure the 3D image setting is  
performed on the TV.  
The 3D images may not be output as set in “HDMI  
Video Out”.  
When performing Fast Forward/Reverse, images are  
shown in 2D.  
Controlling the Blu-ray disc player  
using AQUOS LINK  
What is AQUOS LINK?  
Using the HDMI CEC (Consumer Electronics  
Control), with AQUOS LINK you can interactively  
operate this player with your SHARP AQUOS TV.  
NOTE  
In order to make AQUOS LINK available, set “AQUOS  
Refer to the Operation Manual of the TV for details  
regarding setup.  
What you can do with AQUOS LINK  
CAUTION  
When you connect this player to the LCD TV  
compatible with AQUOS LINK using an HDMI cable,  
you can perform the functions listed below. (See  
When viewing 3D images, viewing for a long period  
of time or lying on your back may cause eye strain  
and discomfort. In addition, 3D images may affect the  
eyesight of young children/infants, so keep them from  
viewing the images.  
Using 3D  
This sets output of 3D images.  
E
Automatic input select function  
To view 3D images, playback of 3D content (3D BD  
video) is necessary with a 3D compatible TV and 3D  
glasses in addition to this player.  
When you start playback of this player, the input  
selector of the LCD TV will automatically switch to  
the LCD TV input terminal connected to the player  
and the playback image will appear on the screen,  
even if you are watching a TV program.  
1 Press c/d to select “Settings”, then press b or  
ENTER.  
2 Press c/d to select “Playback Setting”, then  
E
press b or ENTER.  
Automatic power off function  
3 Press a/b to select “3D Mode”, then press d  
If you turn off the LCD TV when this player is in stop  
mode, the power of this player will be turned off  
automatically. (However, when playing back a disc  
or other content using this player, the power does  
not turn off.)  
or ENTER.  
4 Press a/b to select “Auto”, then press ENTER.  
Auto: Video signals are output as 3D when 3D content  
(3D BD video) is played or as 2D when 2D content is  
played.  
2D: Even if 3D content (3D BD video) is played, video  
signals are output as 2D at all times.  
E
Automatic power on function  
When you switch to the LCD TV input terminal  
connected to this player, the power of this player will  
be turned on automatically.  
24  
   
Before Starting Playback  
Control Panel  
Control Panel  
Major functions of each button icon  
This function allows you to operate this player using  
the TV remote control by displaying the control  
panel on the TV screen.  
Display the pop-up menu screen for BD  
video and the menu screen for DVD video.  
POP-UP  
MENU  
POP-UP  
MENU  
TOP MENU  
TITLE LIST  
FUNC.  
To operate this function, connect this player to a TV  
compatible with HDMI CEC (Consumer Electronics  
that “Control Panel” is set to “Yes” (See page 47). When  
the settings are completed, perform the following  
operations.  
Display the top menu screen for BD video  
and DVD video.  
TOP MENU  
TITLE LIST  
Display the Function Control screen for BD  
video, DVD video, etc.  
FUNC.  
NOTE  
The control panel may not be displayed depending on  
the TV. Also, it may not be available depending on the  
content.  
When operating using the remote control of the player,  
the control panel does not appear.  
Fast reverse (search).  
Play.  
When playing video on demand streaming content  
available with this player, the control panel cannot be  
displayed.  
PANEL  
OFF  
Select  
Enter  
Fast forward (search).  
Skip to the beginning of a chapter.  
Pause.  
1 Switch the TV input to the input source to which  
When there is no operation for approximately  
10 seconds, the control panel disappears  
automatically.  
To display the control panel, press the PLAY button  
on the TV remote control.  
this player is connected (HDMI input).  
2 Press the PLAY button on the TV remote control.  
The control panel appears on the TV screen.  
3 Press a/b/c/d on the TV remote control  
to select the desired button icon, then press  
ENTER.  
The function of the selected button icon is available.  
Skip to the next chapter.  
Jump backward (approx. 10 seconds).  
(This function is used when you want to re-  
watch a scene that has just been shown.)  
Stop.  
Jump ahead (approx. 30 seconds).  
PANEL  
OFF  
Turn off the control panel.  
25  
 
Video/Picture/Music Playback  
NOTE  
Loading a Disc  
BD/DVD Video Playback  
The disc load time may vary depending on the disc.  
BD VIDEO  
BD-RE  
BD-R  
Regarding playback of BD video discs  
Some of the newly released BD video discs cannot be  
played back unless you update the player software  
to the latest version. Therefore, it may be required to  
update the software of the player.  
Refer to pages 55–58 for more information regarding  
software updates for the player.  
DVD VIDEO  
DVD-R DVD-RW  
This section explains playback of commercially  
available BD Video and DVD Video discs (like  
movies) and recorded DVD-RW/R discs.  
This player supports DVD upscaling during DVD  
playback.  
OPEN/CLOSE POWER  
For a description of other playback functions, refer to  
To stop playback  
Press c.  
Resume playback function  
If you press a next, playback will resume from  
the point where the Player was previously stopped. To  
playback from the beginning, cancel resume mode by  
pressing c, then press a. (This may not  
work depending on the type of disc. In this case, open  
the disc tray or enter standby.)  
1 Press POWER to turn on the power.  
2 Press OPEN/CLOSE to open the disc tray.  
3 Load a disc on the disc tray.  
Insert the disc with the label face up.  
In case of disc recorded on both sides, face down  
the side to play back.  
NOTE  
Resume playback may not function depending on the  
disc.  
The resume playback function for discs will be cancelled  
if video on demand streaming content is viewed  
after disc playback. Disc playback will start from the  
beginning after viewing streaming content.  
1 Load a disc.  
Playback may begin automatically, depending on  
the disc.  
Playback begins from the first title.  
The menu may be displayed first, depending on the  
disc. Perform playback operation by following the  
directions on the screen.  
4 Press OPEN/CLOSE to close the disc tray.  
When loading a disc containing 3D content (3D BD  
video) with “Yes” selected in the “3D Notice” setting  
(page 49), playback will be stopped and the 3D notice  
will be displayed on the TV screen. In such cases,  
press ENTER for confirmation, and then playback  
will start.  
2 Press a if playback does not begin  
automatically or playback is stopped.  
26  
         
Video/Picture/Music Playback  
NOTE  
Displaying the disc information  
BD/DVD Menus  
The procedure explained on this page is the basic  
operation procedure. Procedures vary depending on  
the BD/DVD video disc, so you may need to follow the  
instructions in the BD/DVD video disc manual or the  
instructions displayed on the screen.  
This section explains how to play back a BD/DVD  
video disc with a top menu, disc menu or pop-up  
menu.  
The titles listed in the top menu and a disc guide  
(for options like subtitles and audio languages) are  
given in the disc menu.  
Top menu  
With some BD/DVD discs, the top menu may be  
referred to as the “Title Menu”. Use TOP MENU/TITLE  
LIST on the remote control when the instructions refer  
to “Title Menu”.  
Press DISPLAY during playback.  
Each time you press DISPLAY, the display switches  
as follows.  
If no top menu is available, the TOP MENU/TITLE LIST  
button will have no effect.  
1
BD-VIDEO  
Disc Information  
screen A  
Using the disc menu  
2
3
4
1/1  
1/101  
00:00:12  
/03:12:28  
DVD VIDEO  
Example: Select “SUBTITLE LANGUAGE”.  
Start playback by selecting a title  
from the top menu  
1 Press TOP MENU/TITLE LIST.  
The disc menu screen is displayed if present on the  
DVD video disc.  
00:00:12  
/03:12:28  
4
Disc Information  
screen B  
BD VIDEO DVD VIDEO  
2 Press a/b to select “SUBTITLE LANGUAGE”,  
then press ENTER.  
1 Press TOP MENU/TITLE LIST.  
The top menu screen is displayed if present on the  
BD/DVD video disc.  
No Display  
The screen for selecting the subtitle language is  
displayed.  
1 Type of disc  
2 Title number being played / Total number of Titles  
3 Chapter number being played / Total number of  
Chapters  
4 Elapsed playback time / Total playback time for  
the Title  
Example  
Example  
MENU  
T O P M E N U  
1
2
3
AUDIO LANGUAGE  
SUBTITLE LANGUAGE  
AUDIO  
1
3
2
Jazz  
Latin  
NOTE  
4
Classic  
Rock  
Disc Information Screen A disappears after about 1  
minute elapses without performing any operations.  
For some commercially-released BD VIDEO discs, the  
total playback time display for the Chapter/Title may not  
appear.  
2 Press a/b/c/d to select the title, then press  
ENTER.  
3 Press a/b to select the subtitle language, then  
press ENTER.  
The selected title is played back.  
4 Press TOP MENU/TITLE LIST to exit.  
27  
     
Video/Picture/Music Playback  
Virtual Package/BD-LIVE data is saved in Local  
Storage (USB device connected to this Player). To  
enjoy these functions, connect a USB device (2GB  
or greater) supporting USB 2.0 High Speed (480  
Mbps) to the USB1 or USB2 terminal on this player.  
Front  
Using the pop-up menu  
BD VIDEO  
1 Press POP-UP MENU during playback.  
The pop up menu screen is displayed.  
When the wireless LAN adapter is not inserted into the  
USB1 terminal on the rear of the player, it is recommended  
that the USB device be connected to the USB1 terminal.  
(When you insert or remove a USB device, be sure to turn  
the main power off and make sure that “Quick Start” is set  
The menu contents displayed vary depending on  
the disc. For details on how to see and operate the  
pop-up menu, refer to the manual for the disc.  
USB device  
Example  
If there is insufficient storage space, the data will not  
be copied/downloaded. Delete unneeded data or use a  
new USB device.  
Pop-up menu  
NOTE  
If a USB device containing other data (previously  
recorded) is used, the video and audio may not play  
back properly.  
If the USB device is disconnected from this player  
during playback of Virtual Package/BD-LIVE data,  
playback of the disc will stop.  
Some time may be required for the data to load (read/  
write).  
Refer to “USB (HDD/Memory) Management” on page  
54 for erasing the Virtual Package data and the BD-LIVE  
data in the USB device.  
Previous page  
Next page  
A USB device can be used with either the USB1 or  
USB2 terminal. When two USB devices are connected  
to both terminals at the same time, in certain situations  
the USB1 terminal may give priority to Local Storage  
and the USB2 terminal cannot be used for Local  
Storage.  
2 Press a/b/c/d to select the desired item,  
then press ENTER.  
3 Press POP-UP MENU to exit.  
The pop-up menu will automatically disappear for  
some discs.  
Rear  
Enjoying BONUSVIEW or BD-LIVE  
NOTE  
SHARP cannot guarantee that all brands’ USB devices  
will operate with this player.  
BD VIDEO  
Only USB memory devices formatted with FAT 32/16 are  
compatible.  
When formatting a USB memory device using a PC,  
perform the following settings.  
This Player is compatible with additional functions of  
BD-Video, BONUSVIEW (BD-ROM Profile 1 Version  
1.1) and BD-LIVE.  
For BD-Video discs compatible with BONUSVIEW,  
the functions of Picture in Picture and Virtual  
Package are available. For BD-LIVE compatible  
discs, you can enjoy a variety of functions via the  
Internet in addition to the BONUSVIEW functions.  
USB device  
Format File System: FAT32  
Allocation Unit Size: Default Allocation Size  
See page 18 regarding USB HDD formats.  
Do not use a USB extension cable and/or hub when  
connecting a USB memory device to the USB terminal  
of the player.  
Using a USB extension cable and/or hub may prevent  
the player from performing correctly.  
28  
   
Video/Picture/Music Playback  
NOTE  
Use of Picture in Picture function  
(secondary audio/video playback)  
Virtual Package  
Regarding playback method of BD-LIVE contents,  
etc., perform the operations in accordance with the  
instructions in the BD disc manual.  
To enjoy BD-LIVE functions, perform the broadband  
Before using this function, please read “Network Service  
Refer to page 48 regarding the setup to restrict access to  
BD-LIVE contents.  
For BD-Video discs compatible with Virtual  
Package, data is copied from the discs or Internet to  
local storage. It is automatically copied to the local  
storage prior to playback. You can enjoy a variety  
of additional functions including secondary video,  
secondary audio, subtitles, movie trailers, etc.  
The playback methods vary depending on the disc. For  
details, refer to the disc manual.  
BD-Video that includes secondary audio and  
video compatible with Picture in Picture can be  
played back with secondary audio and video  
simultaneously as a small video in the corner.  
If the BD-LIVE screen does not appear for a while after  
you select the BD-LIVE function in the BD disc menu,  
the USB device may not have enough free space. In  
such cases, eject the disc from the player, and then  
erase the data in the USB device in the “USB (HDD/  
BD-LIVE  
In this Player, a variety of contents with interactive  
functions are available through BD-LIVE compatible  
Blu-ray discs by connecting to the Internet. You can  
enjoy the download of bonus features such as latest  
movie trailers to the USB device, communication  
compatible BD-J interactive games, etc.  
Primary audio/  
video  
Secondary audio/  
video  
You can display secondary video from the disc menu.  
NOTE  
The available functions differ depending on the disc.  
To listen to secondary audio, make sure that “Secondary  
The secondary audio and video for Picture In Picture  
may automatically play back and be removed  
depending on the content. Also, playable areas may be  
restricted.  
29  
   
Video/Picture/Music Playback  
About Title List  
DVD-R/-RW (VR format) / BD-RE/-R  
(BDAV format) Playback  
Playback by selecting a title  
The Title List can be displayed in two types,  
Thumbnail and Title Name.  
1 Load a recorded disc.  
Each time you press A (Red), the screen changes  
between Thumbnail and Title Name.  
DVD-R DVD-RW  
BD-RE  
BD-R  
The Title List screen is displayed.  
Example: Thumbnail screen  
You can play back a recorded disc (DVD: VR format  
finalized disc only / BD: BDAV format disc only).  
For a description of other playback functions, refer to  
Thumbnail  
Program 1  
Program 1  
1
5/21 Fri 9:30 AM 110 Min.  
5/21 Fri 9:30 AM 110 Min.  
Program  
1
Program  
2
Program  
3
Program  
1
Program  
2
Program  
3
Program  
4
Program  
5
Program  
6
Program  
4
Program  
5
Program  
6
EXIT  
Select  
Title Name  
Enter  
By Chapter  
Return  
Playlist  
Exit  
Functions  
EXIT  
Select  
Title Name  
Enter  
By Chapter  
Return  
Playlist  
Exit  
Functions  
3
1
A
B
C
D
A
B
C
D
If the Title List screen is not displayed, press TOP  
MENU/TITLE LIST.  
When loading a BD disc with usage restrictions  
placed by a BD recorder, the password input screen  
appears. Then, input your password.  
If you input a wrong password three times, the disc  
tray will open. Close the disc tray, and then input a  
correct password.  
Title Name  
Program 1  
5/21 Fri 9:30 AM 110 Min.  
1 Program 1  
Program  
1
5/21 Fri 110 Min.  
6/15 Fri 110 Min.  
7/3 Mon 56 Min.  
9/18 Thu 40 Min.  
9/20 Sat 20 Min.  
9/25 Thu 60 Min.  
2 Press a/b/c/d to select the desired title, then  
press ENTER to start playback.  
NOTE  
2 Program 2  
3 Program 3  
4 Program 4  
5 Program 5  
6 Program 6  
[From Old]  
“Finalize” refers to a recorder processing a recorded  
disc so that it will play in other DVD players/recorders  
as well as this player. Only finalized DVD discs will play  
back in this player. (This player does not have a function  
to finalize discs.)  
2
3
If you want to select additional titles, switch pages  
by pressing f or g.  
You can playback by pressing a instead of  
pressing ENTER.  
1/All 8 Titles  
EXIT  
Select  
Thumbnail  
Enter  
Return  
Playlist  
Exit  
Functions  
Some discs cannot be played back depending on the  
audio format.  
BD-RE/-R discs recorded from a BD recorder comply  
with AACS copyright protection technology. As this  
player is not intended to be compliant with AACS, such  
discs cannot be played back.  
A
B
C
D
Sorting  
3 Press c to stop playback.  
1 Information of selected title  
2 Title Name  
NOTE  
The Title List screen also can be displayed by pressing  
TOP MENU/TITLE LIST when playback is stopped.  
Recording Date  
Recording Duration  
3 Button Guide  
(AACS: Advanced Access Content System)  
30  
   
Video/Picture/Music Playback  
Playback by selecting a chapter  
Playback by selecting a Playlist  
Playback from the beginning or  
resume playback  
1 Press B (Green) while the Thumbnail screen is  
displayed.  
1 Press C (Blue) while the Title List screen is  
displayed.  
When you play back the title from the Title List after  
you stopped playback, you can select playback  
from the beginning or from the point where it was  
last stopped.  
The chapter screen is displayed.  
The Playlist screen is displayed.  
Example: Thumbnail screen  
Chapter  
1
Chapter  
2
Chapter  
3
Program 1  
1 Press D (Yellow) when the desired title is  
5/21 Fri 9:30 AM 110 Min.  
selected while the Title List screen is displayed.  
Chapter  
4
Chapter  
5
Chapter  
6
Program  
1
Program  
2
Program  
3
2 Press a/b to select the type of Playback, then  
press ENTER to start playback.  
The type of Playback may be selected from “From  
Beginning” or “From Continued”.  
If you want to select additional chapters,  
switch pages by pressing f or  
g.  
Program  
4
3 Press c to stop playback.  
EXIT  
Select  
Title Name  
To return to the Thumbnail screen, press B (Green).  
Enter  
By Chapter  
Return  
Original  
Exit  
Functions  
A
B
C
D
2 Press a/b/c/d to select the desired chapter,  
then press ENTER to start playback.  
You can playback by pressing a instead of  
pressing ENTER.  
2 Press a/b/c/d to select the desired title, then  
press ENTER to start playback.  
3 Press c to stop playback.  
3 Press c to stop playback.  
Sorting the titles  
Each time you press B (Green) while the Title Name  
screen is displayed, the Title Name display changes  
between displaying the newest title first and the  
oldest title first.  
31  
 
Video/Picture/Music Playback  
Playback using a USB device  
Searching by date  
1 Repeat step 1–4 in Searching by title name.  
Searching/sorting the titles  
You can play back video, music and picture data  
stored in a USB device, including a USB HDD and a  
USB memory device.  
Regarding playback of a music or picture file, see pages  
2 Press a/b to select “By Date”, then press  
Searching by title name  
ENTER.  
1 Insert a USB device* to the USB1 or USB2  
The screen for searching by date is displayed.  
terminal.  
When you insert or remove a USB device, be sure  
*
By Date  
to turn off the main power of this player and the  
USB device (only if connecting a USB HDD) and  
make sure that “Quick Start” is set to “No” (See  
To play back a file or content downloaded from a  
From  
To  
Day  
Day  
Month  
Year  
Year  
Month  
Start Search  
2 Press c/d to select Video/Music/Picture, then  
press b or ENTER.  
3 Enter the desired period of dates to search.  
4 Once you enter all the required characters,  
select “Start Search” to start searching.  
The search result will be displayed.  
3 Press c/d to select the desired USB terminal  
(“USB-1” or “USB-2”), then press b or ENTER.  
The Title List screen is displayed.  
Folder 1  
If you cancel the search result and return to the Title  
List screen, press A (Red).  
USB Memory Device/Picture/  
1 Folder 1  
2 Folder 2  
3 Folder 3  
4 Folder 4  
Sorting the titles  
1 Repeat step 1–4 in Searching by title name.  
2 Press a/b to select “Sort”, then press ENTER.  
3 Press a/b to select the desired sorting type  
(“From New”, “From Old” or “Titles”), then press  
ENTER.  
NOTE  
1/All 4 files and folders  
Depending on the format, some files cannot be played  
back.  
To initialize data stored in a USB device or delete BD-  
LIVE data, refer to “USB (HDD/Memory) Management”  
The titles will be displayed according to the  
selected sorting type.  
4 Press A (Red).  
The selection screen for searching/sorting is  
displayed.  
NOTE  
When you sort titles by a sorting type, the type will be  
applied and the titles will be displayed according to the  
selected sorting type until you change the sorting type.  
5 Press a/b to select “By Title Name”, then  
press ENTER.  
6 Enter characters to search using the screen for  
inputting characters.  
For details on the screen for inputting characters,  
7 Searching starts when all required characters  
have been entered.  
The search result will be displayed.  
To cancel the search result and return to the Title  
List screen, press A (Red).  
32  
 
Video/Picture/Music Playback  
Selecting/deleting files  
Copying files/folders  
You can select multiple files on the Title List screen  
to delete or copy all at once.  
You can copy file(s) or folder(s) stored in a USB  
device onto another USB device.  
1 When the Title List screen is displayed, press  
a/b to select the desired file or folder, then  
press B (Green).  
1 When the file(s)/folder(s) are selected at the Title  
List screen, press D (Yellow).  
2 Press a/b to select the destination to copy  
(“USB1” or “USB2”), then press ENTER.  
The selection screen for the destination to copy is  
displayed.  
A check mark is displayed next to the selected file  
or folder.  
The number of selected files and the total file size  
are displayed at the left of the screen.  
3 Press a/b to select a folder to which you want  
Folder 1  
to copy.  
USB Memory Device/Picture/  
1 Folder 1  
Please Select The Copy Destination  
USB1/Picture/Folder1/  
1 File 16MBytes  
2 Folder 2  
*Back  
3 Folder 3  
4 Folder 4  
1.8GBytes  
Folder 1  
Folder 2  
Folder 3  
Folder 4  
1/All 4 files and folders  
*First Page  
To cancel the selection, press B (Green) again.  
Enter  
Copy Start  
2 Repeat step 1 to select other files.  
To move into a folder, select the folder, then press  
Up to 20 items can be selected at once.  
ENTER.  
3 To delete the selected file(s) or folder(s), press C  
(Blue).  
To return to the previous screen, select “Back”, then  
press ENTER.  
To copy the selected file(s) or folder(s) into other  
USB device which is connected to this player, see  
“Copying files/folders” section on this page.  
4 Press D (Yellow) to start copying.  
Copying  
NOTE  
Only the following playable files can be deleted.  
Video: DivX  
Music: MP3  
Picture: JPEG  
Deletion of a folder is not possible if it contains files  
other than playable files.  
To cancel during copying, press c.  
33  
 
Video/Picture/Music Playback  
2 Press a if playback does not begin  
Audio CD Playback  
Operation procedure for the  
“Functions” menu  
automatically or playback is stopped.  
AUDIO CD  
3 To pause the playback at any time, press  
b.  
1 Press D (Yellow) (Functions) when the CD screen  
is displayed.  
Press b or a to return to playback.  
This Player can play back audio CDs.  
For a description of other playback functions, refer to  
4 Press c to stop playback.  
The “Functions” menu is activated.  
5 To return to the HOME screen, press HOME or  
EXIT.  
Playback by selecting a track  
1 Press a/b to select the track, then press  
ENTER during playback or when playback is  
stopped.  
Playback of the selected track will begin.  
2 Press a/b to select the desired setting, then  
press ENTER.  
When playback is stopped, only “Track” can be  
selected.  
For a description of each setting, see “Functions  
3 Press a/b/c/d to set, then press ENTER.  
Operations vary depending on the setting. Follow  
the operation instructions on the screen.  
Playback from the beginning  
4 Press j or D (Yellow) to exit the  
2 Press c to stop playback.  
1 Load an audio CD.  
“Functions” menu.  
The CD screen is displayed.  
(The CD screen is displayed only when a compact  
disc recorded in the CD-DA format is inserted.)  
Playback may begin automatically, depending on  
the disc.  
NOTE  
The displayed items vary depending on the disc.  
34  
   
Video/Picture/Music Playback  
6 To return to the HOME screen, press HOME or  
2 Press c/d to select “Music”, then press b or  
Audio Data (MP3 File) Playback  
EXIT.  
ENTER.  
CD-R  
CD-RW  
DVD-R DVD-RW  
USB  
3 Press c/d to select “DVD/CD ”, “USB-1”,  
*
List of available buttons during playback  
“USB-2” or “Home Network”, then press b or  
Buttons  
a/b  
Description  
Select a desired audio file.  
Play back audio file.  
This Player can play back audio data (MP3 files)  
recorded on CD-R/RW discs, DVD-R/RW discs and  
USB devices or via a home network.  
For details on the audio data that you can play using  
this player, refer to page 11.  
ENTER.  
Display name varies depending on the type of  
media inserted.  
*
ENTER  
4 Press a/b to select a folder or file.  
When you select a folder, press ENTER to open it,  
and then press a/b to select a file in the folder.  
Pause audio file playback.  
Return to playback when  
paused.  
b
Folder 1  
Skip backward.  
Skip forward.  
Stop playback.  
f
g
c
CD  
1 Folder 1  
2 Folder 2  
3 Folder 3  
4 Folder 4  
NOTE  
5 Track 01.mp3  
6 Track 02.mp3  
1/All 14 files and folders  
The Fast Forward/Reverse function does not work.  
The Repeat function does not work.  
5 Press ENTER to play back the selected file.  
Playback of the selected file will begin.  
1 Load a disc or a USB device containing audio  
*
data (MP3 files).  
*
When you insert or remove a USB device, be sure  
to turn off the main power of this player and the  
USB device (only if connecting a USB HDD) and  
make sure that “Quick Start” is set to “No” (See  
When MP3 files are played, the “Functions” menu is  
not available.  
35  
 
Video/Picture/Music Playback  
6 To return to the HOME screen, press c,  
4 Press a/b to select a folder or file.  
When you select a folder, press ENTER to open it,  
and then press a/b to select a file in the folder.  
Displaying Still Images (JPEG files)  
and then press HOME or EXIT.  
CD-R  
CD-RW  
DVD-R DVD-RW  
USB  
Operational buttons during still image  
display  
Folder 1  
This Player can display still images (JPEG files)  
recorded on CD-R/RW discs, DVD-R/RW discs and  
USB devices or via a home network.  
For details on the still images that you can display using  
this player, refer to page 11.  
Still images are played one by one while during “Slide  
show”, they are automatically replaced one after  
another.  
Buttons  
Description  
CD  
1 Folder 1  
2 Folder 2  
3 Folder 3  
4 Folder 4  
5 Image 01.jpg  
6 Image 02.jpg  
1/All 14 files and folders  
Go to the previous/next picture in  
the same directory.  
f/  
g
d/ e  
j
C (Blue)  
Return to the selection screen.  
Rotate the picture by 90 degrees  
to the left.  
To set slide show speed/repeat playback, press C  
(Blue)*. For details, refer to the following table.  
D (Yellow)  
Rotate the picture by 90 degrees  
to the right.  
When using a USB device, the “Delete” function  
*
is also available. When you press C (Blue) after  
selecting folders/files using B (Green), the “Delete”  
and “Slide Show Menu” selection screen will be  
displayed.  
Play back Slide Show.  
Return to slide show playback  
when paused.  
a
Pause slide show playback.  
b
c
Slide Show Menu  
Stop still image display/slide show  
playback.  
Slide Show  
Speed  
Setting of slide show playback  
speed  
A (Red)  
NOTE  
Guide display on/off  
Repeat Mode  
Setting  
Setting of slide show repeat  
playback  
Guide Display  
Setting  
Guide display setting during still  
image display  
Thumbnail data will be displayed when JPEG files from  
a digital camera contain thumbnail data.  
An icon will be displayed for JPEG files which do not  
contain thumbnail data.  
1 Load a disc or a USB device containing Still  
*
5 Press ENTER to display the selected file.  
Images (JPEG files).  
*
The selected still image appears on the screen.  
When you insert or remove a USB device, be sure  
to turn off the main power of this player and the  
USB device (only if connecting a USB HDD) and  
make sure that “Quick Start” is set to “No” (See  
1/77  
2 Press c/d to select “Picture”, then press b or  
ENTER.  
3 Press c/d to select “DVD/CD ”, “USB-1”,  
*
“USB-2” or “Home Network”, then press b or  
ENTER.  
Display name varies depending on the type of  
media inserted.  
*
36  
   
Video/Picture/Music Playback  
Accessing DLNA servers  
3 Press a/b to select a DLNA server which you  
want to access, then press ENTER or d.  
The folder list or file list of the DLNA server which  
you accessed is displayed.  
* Playing MKV files via Home Network  
To play MKV files via DLNA server, you will need to  
download and install “DivXinstaller.exe” on a DLNA  
compatible PC (Windows 7), which can be found on  
Make the necessary settings and confirm that an MKV  
file can be played using Windows Media Player on a  
PC prior to attempting playback on the LCD TV.  
The player can browse and play movies, music and  
photos stored on your DLNA Certified media servers  
connected within your home network.  
Select server  
About a home network  
This Player can display and play movies, photos  
and music content from your DLNA-compatible  
digital media servers (such as a PC and consumer  
electronics).  
1. xxxxxxxxxxxxx  
2. yyyyyyyyyyyyy  
3. zzzzzzzzzzzzzz  
4. aaaaaaaaaaaa  
NOTE  
Even if DLNA compatible, a connection may not be  
able to be made depending on the server, or playback  
may not be available even if a connection is made  
successfully.  
Some files may not be playable depending on the file.  
To enjoy this function, make a broadband Internet  
connection to both your PC and this player (See pages  
19–20), and then set communication settings (See pages  
To use this function, we recommend setting “Auto  
Before accessing DLNA servers:  
DLNA servers and this player must be connected to the  
same local area network. Specify the settings required  
for connecting this player to the local area network.  
DLNA servers must be turned on.  
When a PC running DLNA server software or other  
DLNA-compatible devices are connected to this player,  
some setting changes of software or other devices may  
be required.  
The previous screen appears when j  
is pressed.  
4 Press a/b to select the folder or file which you  
want to access, then press ENTER.  
When you select a folder, the file list of the folder is  
displayed. Press a/b to select the file which you  
want to play, then press ENTER.  
Please refer to the operating instructions for the  
software or devices for more information.  
Playback starts.  
Before using this function, please read “Network Service  
Root  
Playback by selecting a file list  
Folder1  
Folder2  
1 Press c/d to select Video/Music/Picture, then  
Video01.divx  
Video02.divx  
Video03.divx  
Video04.divx  
1/ALL 40 files and folders  
press b or ENTER.  
2 Press c/d to select “Home Network”, then  
press b or ENTER.  
For operation during playback, refer to pages 38–39.  
Video  
Music  
Picture  
e-Contents  
Settings  
5 Press c to stop playback.  
The file list reappears.  
The previous screen appears when j  
is pressed.  
BD-VIDEO  
USB-1  
USB-2  
Home Network  
Next  
6 Press EXIT or HOME to exit playback.  
Types of playable files  
The HOME screen reappears.  
Video  
DivX Plus HD (avi/divx/mkv)  
The player automatically scans and displays DLNA  
servers within your local network.  
Music  
Picture  
mp3  
jpg  
37  
   
Playback Functions  
Fast Forward/Reverse (Search)  
Pause/Frame Advance Playback  
BD VIDEO  
DVD VIDEO  
AUDIO CD  
BD-R  
BD-RE  
BD VIDEO  
BD-R  
BD-RE  
DVD-R DVD-RW  
DVD VIDEO  
DVD-R DVD-RW  
The Pause function is enabled when b is  
pressed during playback. (If you are playing back  
an audio CD, audio data [MP3 files] or still images  
[JPEG files], these will also pause.)  
The Fast Forward/Reverse function is enabled when  
d or e is pressed during playback.  
Example: When e is pressed  
The search speed will change each time you press the  
button.  
The Frame Advance Playback function is enabled  
when g is pressed during pause.  
Frame Advance Playback may not function properly  
with discs other than DVD-RW/R (VR format).  
When playing back a DVD  
You cannot perform Fast Forward/Fast Reverse from  
one title and continue to another title (except when  
playing audio CDs). At the end or beginning of the title,  
Fast Forward/Fast Reverse will be cancelled and normal  
playback will automatically resume.  
NOTE  
Some BD/DVD Video discs are not compatible with  
Pause/Frame Advance Playback.  
Frame Advance/Reverse Playback can be performed  
for DVD discs by pressing g or  
f during pause.  
Frame Reverse Playback cannot be performed for DivX  
video.  
NOTE  
Subtitles are not played back with BD/DVD video discs  
during Fast Forward and Fast Reverse.  
Skipping to the Next or the Start of  
the Current Chapter (Track/Title)  
Slow Playback (Forward/Reverse)  
NOTE  
BD VIDEO  
DVD VIDEO  
AUDIO CD  
BD-R  
DVD-R DVD-RW  
CD-R CD-RW  
BD-RE  
BD VIDEO  
BD-R  
BD-RE  
Some operations in the following playback functions  
cannot be performed depending on the specifications of  
the disc.  
DVD VIDEO  
DVD-R DVD-RW  
USB  
The Slow Playback (Forward/Reverse) function is  
enabled when g or f is  
pressed for more than 2 seconds during pause.  
Press a to return to normal playback.  
The Skipping (to the beginning of a chapter, track  
or title) function is enabled when f or  
g is pressed during playback.  
NOTE  
This doesn’t work for audio CDs.  
You cannot perform Slow Playback between titles. At  
the end of the title, Slow Playback will be cancelled and  
normal playback will automatically resume.  
Reverse Slow Playback cannot be performed for BD  
video and DVD discs in AVCHD format.  
Reverse Slow Playback cannot be performed for DivX  
video.  
38  
         
Playback Functions  
5 Press ENTER.  
4 Press ENTER at the scene where you want to  
set the start point.  
Repeat Playback of a Title or  
Chapter (Repeat Playback)  
Example: Repeat playback of a title (TITLE)  
“Set End Point” displays.  
BD-VIDEO  
5 Press ENTER at the scene where you want to  
set the end point.  
BD VIDEO  
DVD VIDEO  
AUDIO CD  
BD-R  
BD-RE  
1/3  
5/25  
00:20:30  
2 English  
1
DVD-R DVD-RW  
You can press e to fast forward to the  
scene where you want to set the end point. When  
you reach the desired scene, simply press a  
and then ENTER to set the end point.  
1 DTS  
On Title Repeat  
1 Play back the title or chapter you want to repeat.  
NOTE  
2 Press FUNCTION.  
Press g, the Repeat Playback is  
cancelled and the next chapter being played back.  
Press f once, the Repeat Playback is  
cancelled and the player returns to the start of current  
chapter (track).  
If you press f again (within about 5  
seconds) the player will skip to the beginning of the  
previous chapter (track).  
For Partial Repeat Playback, set the start and end  
points within the same title.  
Repeat Playback may be forbidden depending on the  
disc.  
The Function Control screen is displayed on the TV.  
3 Press a/b to select the Repeat column, then  
press ENTER.  
On Title Repeat  
4 Press a/b to select the type of Repeat  
Playback.  
Playback Title: Repeats the title currently being  
played back.  
6 Press j or FUNCTION to close the  
Function Control screen.  
Playback Chapter: Repeats the chapter currently  
being played back.  
Scene Selection: Repeats the specified scene of  
title or chapter.  
NOTE  
“Scene Selection” operation is not available for BD  
video.  
Partial Repeat Playback may not work in multi-angle  
scenes.  
If you press DISPLAY, you can confirm the Repeat  
Playback status.  
NOTE  
Press j to cancel without setting the type  
of Repeat Playback.  
For Audio CD, you can select “Playing Disc”, “Playing  
Track” and “Specify The Part” as Repeat Playback  
options.  
Partial Repeat Playback (Repeat  
Playback of a Specified Part)  
DVD VIDEO  
DVD-R DVD-RW  
AUDIO CD  
Repeat Playback cannot be performed for DivX video.  
1 Press FUNCTION during playback.  
The Function Control screen is displayed on the TV.  
2 Press a/b to select the Repeat column, then  
press ENTER.  
3 Press a/b to select “Scene Selection”, then  
press ENTER.  
“Set Start Point” displays.  
39  
     
Playback Functions  
2 Press a/b to select the Angle Number column,  
Displaying the Audio Information  
Switching Subtitles  
then press ENTER.  
BD VIDEO DVD VIDEO  
You can display the audio information on the disc  
currently being played back by pressing AUDIO.  
The displayed contents vary depending on the disc.  
BD-VIDEO  
If subtitles are provided in multiple languages, you  
can switch between them.  
1/3  
5/25  
00:20:30  
2 English  
1
1 DTS  
Off  
BD VIDEO DVD VIDEO  
Press SUBTITLE during playback.  
The audio channel currently being played back will  
be displayed.  
If multiple audio channels are recorded, you can  
switch the audio channel by pressing AUDIO.  
The display indicates the subtitle number currently  
being played back, and the subtitles appear.  
Each time SUBTITLE is pressed, the subtitles change.  
“–” is displayed if a disc has no subtitles.  
You can also select “Off”.  
3 Press a/b to select the desired Angle Number,  
then press ENTER.  
DVD-RW DVD-R  
4 Press j or FUNCTION to close the  
NOTE  
Function Control screen.  
When a recorded broadcast with stereo or  
monaural audio is played back:  
“Stereo” is displayed. (Audio cannot be switched.)  
Settings for subtitles can also be changed in the  
Function Control screen (Page 41).  
The operation of subtitles differs according to each disc.  
You may need to refer to the operation manual of the  
disc.  
The display for subtitle information automatically  
disappears after 5 seconds.  
NOTE  
The displayed items vary depending on the disc.  
If you access the Function Control screen during  
playback of a BD/DVD video, it may be impossible to  
operate the BD/DVD video playback. In cases like this,  
close the Function Control screen.  
The operation of angles differs according to each disc.  
You may need to refer to the operation manual of the  
disc.  
NOTE  
When you play a program recorded in stereo or  
monaural, and if you are listening to the Bitstream  
sound via the digital output jack, you cannot select the  
Settings for audio can also be changed in the Function  
The operation of audio differs according to each disc.  
You may need to refer to the operation manual of the  
disc.  
Switching the Angle  
The display for angle information automatically  
disappears after 5 seconds.  
BD VIDEO DVD VIDEO  
If multiple angles are recorded, you can switch  
between them.  
The display for audio information automatically  
disappears after 5 seconds.  
Displaying the Angle Mark  
1 Press FUNCTION during playback.  
BD VIDEO DVD VIDEO  
The Function Control screen is displayed on the TV.  
You can change settings so that Angle Mark appears  
in the right bottom part of the screen when multiple  
angles are recorded. The settings can be changed  
in “Settings” – “Playback Setting” – “Angle Mark  
40  
     
Settings During Playback  
3 Operation guide display  
Provides help on remote control button operations.  
3 Press a/b/c/d to set, then press ENTER.  
Operations vary depending on the setting. Follow  
the operation instructions on the screen.  
Function Control  
BD VIDEO  
DVD VIDEO  
AUDIO CD  
BD-R  
BD-RE  
4 Press j or FUNCTION to close the  
Function control operation  
procedure  
DVD-R DVD-RW  
Function Control screen.  
NOTE  
If “– –” is displayed for an option like title number or  
subtitles, the disc has no titles or subtitles which can be  
selected.  
The displayed items vary depending on the disc.  
If you access the Function Control screen during  
playback of a BD/DVD video, it may be impossible to  
operate the BD/DVD video playback. In cases like this,  
close the Function Control screen.  
This allows you to adjust various settings at once,  
like subtitles, angle settings and the title selection  
for Direct Playback. You can adjust the video and  
audio to suit your preferences. The operations are  
the same for BD and DVD.  
Function Control screen  
BD-VIDEO  
1
1/3  
5/25  
00:20:30  
2
2 English  
1
1 DTS  
Off  
1 Press FUNCTION during playback.  
The Function Control screen is displayed on the TV.  
ENTER  
Select  
Enter  
Return  
2 Press a/b to select the desired setting, then  
press ENTER.  
EXIT  
Exit  
3
For a description of each setting, see “Functions  
1 Playback status display  
BD-VIDEO  
Shows the operation status and the disc type.  
1/3  
5/25  
00:20:30  
2 English  
1
1 DTS  
Off  
2 Setting items  
Selects a title (or track) or chapter for playback, or  
performs video/audio settings.  
Title/Track Number (Direct Title/Track Skip)  
Chapter Number (Direct Chapter Skip)  
Playback Elapsed Time (Direct Time Skip)  
Subtitle Language  
Angle Number  
Audio  
Repeat  
41  
   
Settings During Playback  
Subtitle Language  
Functions which can be set  
Shows the currently selected subtitle language. If  
subtitles are provided in other languages, you can  
switch to your preferred language.  
Title/Track Number (Direct Title/Track Skip)  
Shows the title number being played back (or track  
number when playing back an audio CD). You can skip  
to the start of the title (or track).  
To skip to the start of a selected title (or track), press  
the Number buttons to enter the title (or track) number  
when this option is highlighted.  
Angle Number  
Shows the currently selected angle number. If the video  
is recorded with multiple angles, you can switch the  
angle.  
Audio  
Chapter Number (Direct Chapter Skip)  
Shows the chapter number being played back. You can  
skip to the start of the chapter.  
Shows the currently selected type of audio. You can  
select the desired type of audio.  
To skip to the start of a selected chapter, press the  
Number buttons to enter the chapter number when this  
option is highlighted.  
Repeat  
The current Title (or Chapter) or partial segments can be  
repeatedly played back.  
Playback Elapsed Time (Direct Time Skip)  
NOTE  
Shows the time elapsed from the beginning of the  
current disc title (or track). This lets you skip to a  
specific time.  
These functions may not work with all discs.  
Press c/d to select the Hour, Minute or Second, then  
press a/b or the Number buttons to set the time.  
Press ENTER to start playback at the set time.  
42  
   
Enjoying smartphone on the TV (for BD-AMS20U only)  
This player allows you to view smartphone displays  
on your TV. By connecting your smartphone to this  
1 Press POWER to turn on the player.  
When a disc or USB device is inserted or played  
back, stop playback, and then press HDMI to  
switch the HDMI input.  
Disclaimers  
Sharp does not provide any guarantee in regards to  
operational failures such as those described below  
when an MHL device is connected to this player.  
player with an MHL cable, you can enjoy a variety  
*
of smartphone content with high definition audio  
and video on your TV, including VOD content, Web  
browsing, Widget, games and news.  
“  
” will be displayed on the front panel display  
when the TV input is switched to MHL/HDMI.  
No picture or sound  
Some functions do not work during operation.  
MHL (Mobile High-definition Link)  
*
If the MHL device does not work properly, refer to  
the operation manual for the MHL device or directly  
contact the manufacturer.  
MHL is a mobile audio and video interface standard for  
transmitting digital audio and high definition (HD) video  
(1080p/30fps) without any compression.  
An MHL-compatible smartphone is available for this  
function.  
To operate this function, also connect this player to a  
TV compatible with HDMI CEC (Consumer Electronics  
2 Connect an MHL cable to the HML/HDMI INPUT  
terminal of this player and the smartphone.  
Make sure that the TV is connected to this player  
with an HDMI cable.  
NOTE  
3 Switch the TV input to the input source to which  
this player is connected (HDMI input).  
Prepare an MHL-compatible cable. For MHL-compatible  
smartphones to be connected, refer to the smartphone  
carrier.  
Some smartphone applications may not be compatible  
with the TV.  
For further details, refer to the operation manual of the  
connected smartphone.  
The screen on which the connected smartphone is  
displayed will be displayed on the TV.  
4 Use the TV remote control for the smartphone  
operation.  
NOTE  
The remote control of this player is not compatible for  
the smartphone operation on the TV.  
Do not turn off the power of this player during the  
operation.  
Connecting a smartphone  
You can connect a smartphone or HDMI equipment  
to the MHL/HDMI INPUT terminal of the player.  
Rear  
Recharging the battery of the  
smartphone  
This player has a recharging function for  
smartphones. By connecting to the player with an  
MHL cable, smartphone can be recharged during  
the operation.  
MHL/HDMI  
INPUT terminal  
*
NOTE  
The smartphone is not recharged when you connect  
it to any terminal other than the HML/HDMI INPUT  
terminal.  
MHL cable  
Only the BD-AMS20U model has the MHL/HDMI INPUT  
terminal.  
*
43  
 
Settings  
SETTINGS  
Common operations  
The “menu” enables various audio/visual settings  
and adjustments on the functions using the remote  
control unit. You need to call up the On Screen  
Display to perform settings for this player. The  
following is the explanation for the basic operations  
of the “menu”.  
Home screen display  
1
2
Press c/d to select “Settings”, then press b or ENTER.  
Press c/d to select “Smart Settings”, then press b or ENTER.  
Video  
Music  
Picture  
e-Contents  
Settings  
Audio Video  
Settings  
Smart Settings Playback Setting Communication  
Setup  
USB (HDD Memory) Software Update  
System  
Management  
Settings  
Example: Setting “AQUOS LINK”  
Next  
Select a menu item  
Quick Start  
Press a/b to select “AQUOS LINK”, then press d or ENTER.  
Auto Power Off  
Front Display/LED  
Control Panel  
Screen Saver  
AQUOS LINK  
Yes  
No  
Select the next item  
Press a/b to select the desired item, then press ENTER.  
Press j to return to the previous “menu” page.  
Exit the menu screen  
Press HOME or EXIT to exit.  
44  
   
SETTINGS  
5 Press c/d to select the parental control level  
for DVD VIDEO, BD-ROM, and then select the  
country code. Press ENTER after making each  
selection.  
Basic Operation for Playback  
Setting  
Example: Setting “Parental Control” under “Playback  
Setting”  
Parental Control  
Disc Language  
Angle Mark Display  
Password Setting  
BD Internet Access  
3D Mode  
1 Press c/d to select “Settings”, then press b or  
ENTER.  
2 Press c/d to select “Playback Setting”, then  
press b or ENTER.  
Level 3  
0
3D Notice  
3 Press a/b to select “Parental Control”, then  
press d or ENTER.  
When you operate this Player for the first time,  
the password setting screen will be displayed.  
See “When setting the password for the first time”  
below.  
USA  
6 Press HOME or EXIT to exit.  
4 Enter your 4-digit password.  
You cannot move to the next setting screen until  
you can input the correct password.  
When setting the password for the first time.  
1
To set the password for the first time, press  
a/b to select “Yes” to enter the password  
setting menu, then press d or ENTER.  
2
3
Enter a 4-digit number for the password, then  
the same 4-digit number for confirmation.  
Press ENTER to complete the password setting  
procedure and move to the next setting screen.  
45  
 
SETTINGS  
2
This sets the audio output mode for DIGITAL  
AUDIO OUT (OPTICAL terminal) when selecting  
“Digital Output”.  
Audio Out  
Audio Video Settings  
You can set the audio output when connecting to  
SURROUND equipment.  
HDMI Video Out  
Item  
1 This sets the audio output connected to  
Bitstream:  
This sets the resolution of the video output for the  
HDMI terminal of this player.  
SURROUND equipment.  
Select this when connecting to SURROUND  
equipment with a built-in decoder for DOLBY  
DIGITAL, etc.  
Setting to Bitstream will output each audio signal by  
Bitstream.  
Normally set to “Auto” (factory preset value).  
Item  
Item  
HDMI Output: Select this when you connect using  
HDMI OUT terminal.  
Digital Output: Select this when you connect using  
DIGITAL AUDIO OUT terminal (OPTICAL).  
Auto, 1080p, 1080i, 720p, 480p  
PCM:  
Select this when connecting to 2 channel stereo audio  
equipment.  
Setting to PCM will output by converting each audio  
signal into PCM 2 channel audio signal.  
NOTE  
When the BD player is connected to a 1080p 24Hz  
compatible TV and the “HDMI Video Out” is set to  
“Auto”, 1080p 24Hz will automatically be displayed  
when compatible discs are played back.  
2 You can set the audio output mode for each  
output terminal.  
NOTE  
1
This sets the audio output mode for HDMI OUT  
terminal when selecting “HDMI Output”.  
Secondary Audio  
NOTE  
This toggles the clicking sound on the menu and  
audio with secondary video in picture in picture  
mode for BD-Video.  
Select “Off” when enjoying the high quality sounds of  
BD-Video.  
When the secondary audio is set to “On”, PCM is  
automatically selected as the audio output mode.  
Item  
Bitstream:  
Item  
Select this when connecting to HDMI equipment with  
a built-in decoder for DOLBY DIGITAL, etc.  
Setting to Bitstream will output each audio signal by  
Bitstream.  
On, Off  
PCM (Surround):  
Select this when connecting to multi-channel HDMI  
equipment.  
Setting to PCM (Surround) will output by LINEAR  
PCM by decoding audio signals recorded in each  
audio output mode such as DOLBY DIGITAL, DTS.  
46  
       
SETTINGS  
Item  
Dynamic Range Control  
Smart Settings  
On, Dimmer, Off  
This lets you adjust the range between the loudest  
and softest sounds (dynamic range) for playback  
at average volume. Use this when it is hard to hear  
dialog.  
Quick Start  
NOTE  
When “Dimmer” is selected, the BD/DVD/CD mode  
indicator turns off.  
This turns the Quick Start function on and off.  
When the Quick Start function is on:  
The startup time of the Player is reduced.  
However, power consumption will increase.  
When the Quick Start function is off:  
The player will enter the low power consumption mode  
when in standby condition.  
Item  
Control Panel  
Normal: The same audio output range is played as the  
original recorded audio output range.  
Shift*: When Dolby Digital audio is played back, the  
dynamic range of the audio is adjusted so that the  
dialog portion can be heard easily. (If the audio  
sounds abnormal, set to “Normal”.)  
This lets you set display of the control panel on the  
TV screen to on or off.  
Item  
Item  
Yes, No  
Yes, No  
Auto: When you play back audio in the Dolby TrueHD  
format, the dynamic range is automatically adjusted.  
NOTE  
Screen Saver  
Lower the audio volume before setting. If you do not do  
so, the speakers may emit a loud sound or excessive  
output may be applied to the speakers.  
*
When “Quick Start” is set to “Yes”, the Player requires  
some time to turn off.  
This function helps prevent burn-in on the TV screen  
by leaving the player with the power turned on for a  
long period of time.  
Auto Power Off  
SUPER PICTURE  
Item  
This sets the Player so that power is automatically  
shut off if playback is stopped and you do not  
perform any operations for about 10 minutes.  
This enhances the quality of video streaming images  
with pixel by pixel processing technology.  
Yes, No  
Item  
AQUOS LINK  
Item  
On, Off  
Yes, No  
This lets you set the Player to receive the control  
signal from the AQUOS LINK remote control via the  
HDMI cable.  
Front Display/LED  
Item  
If you feel that the indicators on the player’s front  
display are too bright when watching movies, you  
can turn them off except for the POWER (ON/  
STANDBY) indicator.  
Yes, No  
NOTE  
For details, refer to the operation manual of TV.  
You can also adjust the brightness of the front  
display/LED light by selecting “Dimmer”.  
47  
         
SETTINGS  
Disc Language (Disc Priority Language)  
Password Setting  
Playback Setting  
This lets you select the language for subtitles, audio  
and menus displayed on the screen.  
This sets the password for setting or changing the  
Parental Control Level.  
Parental Control  
This lets you set the Parental Control depending  
on the disc content. The available Parental Control  
Levels are shown below.  
Item (Subtitle)  
Item  
Select the subtitle language you want to display.  
Yes: Enter the 4-digit number.  
No  
The 4-digit password number needs to be entered  
before the Parental Control Levels and the Country  
Code are set. The Parental Control Levels and the  
Country Code cannot be set if a password has not  
been created or the password is not entered.  
Select the rating level appropriate for the age of the  
user.  
Item (Audio)  
NOTE  
Select the audio language you want to hear.  
When you forget the password, you can reset the  
current password using “System Reset” under  
Item (Menu)  
Select the menu language you want to display.  
You can also set the new password if desired.  
NOTE  
Item (Parental control level for DVD-video)  
BD Internet Access  
When “Auto” is selected, the priority language of the  
disc will be played back.  
8 and Off: All DVD-video can be played.  
1–7: Prohibits play of DVD-video with corresponding  
ratings recorded on them.  
This allows you to set access restriction to BD-LIVE  
contents.  
Angle Mark Display  
Item  
Item (Parental control level for BD-video)  
This lets you turn the Angle Mark Display on or off  
when BD/DVD video recorded with multiple angles  
is played back. (The Angle Mark is displayed in the  
lower right screen.)  
Permit: Allows all BD-LIVE discs.  
Limit: Allows only discs with owner certification.  
Prohibit: Prohibits all BD-LIVE discs.  
No Limit: All BD-video can be played.  
0–99 year(s): Prohibits play of BD-video with  
corresponding ratings recorded on them.  
NOTE  
Item (Country code)  
Item  
The available functions differ depending on the disc.  
Regarding playback method of BD-LIVE contents,  
etc., perform the operations in accordance with the  
instructions in the BD disc manual.  
To enjoy BD-LIVE functions, perform the broadband  
Select the country code.  
The ratings differ according to the country.  
Yes, No  
NOTE  
Refer to “Basic Operation for Playback Setting” on page  
48  
     
SETTINGS  
3D Mode  
DivX(R) Deregistration  
System  
This sets output of 3D images.  
You can deactivate your DivX information on the  
player.  
Version  
To view 3D images, playback of 3D content (3D BD  
video) is necessary with a 3D compatible TV and 3D  
glasses in addition to this player.  
When you select “Version”, the system software  
version and Netflix ESN are displayed.  
Item  
Yes, No  
Item  
On Screen Language  
NOTE  
Auto: Video signals are output as 3D when 3D content  
(3D BD video) is played or as 2D when 2D content is  
played.  
2D: Even if 3D content (3D BD video) is played, video  
signals are output as 2D at all times.  
You can set the language you want to display on the  
screen.  
VUDU Deactivate  
Item  
English, Español, Français  
You can deactivate your VUDU information on the  
player.  
CAUTION  
When viewing 3D images, viewing for a long period  
of time or lying on your back may cause eye strain  
and discomfort. In addition, 3D images may affect the  
eyesight of young children/infants, so keep them from  
viewing the images.  
Netflix Deactivate  
Item  
You can deactivate your Netflix information on the  
player.  
Yes, No  
System Reset  
Item  
Yes, No  
3D Notice  
You can reset all settings to the factory presets.  
Item  
This sets whether or not a notice is displayed on the  
connected TV every time 3D content (3D BD video)  
is played.  
DivX(R) Registration  
Reset, Not Reset  
The DivX registration code is displayed.  
Item  
NOTE  
Yes, No  
49  
     
SETTINGS  
4 Press a/b to select “Change”, then press  
Communication Setup  
Sets whether “Cable” or “Wireless”  
is used for the network connection  
ENTER.  
This allows you to perform and/or change the  
communication settings and select the type of  
Internet connection from Cable or Wireless. This  
setting is required to use BD-LIVE functions, video  
on-demand services (e-Contents), home networks  
and software updates that connect to the Internet.  
Current Ethernet setup info.  
1 Press c/d to select “Settings”, then press b or  
IP Address : Auto Setup  
Netmask : Auto Setup  
ENTER.  
2 Press c/d to select “Communication Setup”,  
Gateway  
DNS  
: Auto Setup  
: Auto Setup  
then press b or ENTER.  
3 Press a/b to select “Cable/Wireless Select”,  
NOTE  
then press d or ENTER.  
Change  
Initialize  
Make sure that the LAN cable or the wireless LAN  
adapter is connected to this player and make sure that  
the wireless router/access point is connected to the  
Internet if using the wireless LAN adapter. (See pages  
For manually performing the setting, the following  
information of the connected router or modem is  
required. Confirm the information prior to the setting.  
IP address, netmask, gateway, DNS address  
4 Press a/b to select “Cable” or “Wireless”, then  
press ENTER.  
If selecting “Cable”, follow the [When selecting  
Cable] directions on this page, then go to step 3.  
If selecting “Wireless”, follow the [When selecting  
Wireless] directions on the next page, then go to  
step 3.  
For initializing the current setting, select “Initialize”,  
then press ENTER.  
5 For setting the IP address, press c/d to select  
Yes” or “No”, then press ENTER.  
NOTE  
Do you obtain the IP address  
automatically?  
When selecting “Wireless” when the wireless LAN  
adapter is not inserted, “Wireless LAN adapter is not  
inserted” appears on the screen.  
Yes  
No  
IP Address  
Netmask  
Gateway  
When selecting Cable  
Next  
1 Press c/d to select “Settings”, then press b or  
ENTER.  
If selecting “Yes”: The IP address is automatically  
obtained.  
If selecting “No”: The IP address, netmask and  
gateway are manually entered using the screen for  
Regarding each of the setup values, confirm the  
specifications of your broadband router.  
2 Press c/d to select “Communication Setup”,  
then press b or ENTER.  
3 Press a/b to select “Ethernet Setup (Cable)”,  
then press d or ENTER.  
6 Select “Next”, then press ENTER.  
If selecting “Yes” in the step 5, go to the step 9.  
50  
     
SETTINGS  
7 Enter your DNS address.  
5 The player scans all of the available access  
points and displays the points with the “Other  
Network” selection bar on the screen.  
When selecting Wireless  
Enter your DNS address.  
CAUTION  
During searching access point(s), “Accessing...”  
appears on the screen.  
We recommend writing down the MAC address of  
the connected wireless LAN adapter in this operation  
MAC address is labeled on the adapter or displayed on  
the “Current Ethernet setup info.” screen (See step 5  
below).  
When performing the wireless communication setup,  
security information for the wireless router/access  
point (WEP, WPA or WPA2 key) is required. Check your  
wireless router/access point’s information prior to setup.  
Primary  
Up to 6 items (5 access points and the “Other  
Network” selection bar) are displayed on the screen.  
When there are six or more items retrieved, display  
the next screen by selecting “Next”, then pressing  
ENTER. (The “Other Network” selection bar is  
always displayed last.) When no available access  
points are retrieved, only the “Other Network”  
selection bar is displayed on the screen.  
Secondary  
Next  
The primary and secondary DNS addresses are  
entered using the screen for inputting characters.  
Regarding each of the setup values, confirm the  
specifications of your broadband router.  
6 Press a/b to select “desired access point” or  
“Other Network”, then press ENTER.  
For access points which are set to hide the SSID  
using the wireless router, select “Other Network” to  
set the access point.  
NOTE  
8 Select “Next”, then press ENTER.  
Wireless communication setup cannot be performed  
when the wireless LAN adapter is not inserted.  
Before this player can access the Internet wirelessly,  
setup of a wireless router/access point is required.  
9 For testing the connection to the Internet, after  
confirming the settings, press a/b to select  
Test”, then press ENTER.  
Test” is available only when setting to obtain the IP  
address automatically. “Test” cannot be selected if  
the IP address has not been obtained automatically.  
Select the access point.  
1 Press c/d to select “Settings”, then press b or  
XXXXXXXXXXXX  
YYYYYYYYYYYY  
Other Network  
ENTER.  
Confirm the current setting.  
2 Press c/d to select “Communication Setup”,  
then press b or ENTER.  
IP Address : xxx xxx xxx xxx  
3 Press a/b to select “Ethernet Setup  
Netmask  
Gateway  
: xxx xxx xxx xxx  
: xxx xxx xxx xxx  
If selecting “desired access point”, go to step 9.  
If selecting “Other Network”, go to the next step.  
(Wireless)”, then press d or ENTER.  
DNS Address : xxx xxx xxx xxx  
xxx xxx xxx xxx  
MAC Address : xx xx xx xx xx xx  
4 Press a/b to select “Change”, then press  
ENTER.  
Test  
Current Ethernet setup info.  
Complete  
MAC Address : xx xx xx xx xx xx  
Access Point : Not Selected  
IP Address : Auto Setup  
As a result of the test, if the Internet connection  
fails, enter the setup values manually.  
Netmask  
Gateway  
DNS  
: Auto Setup  
: Auto Setup  
: Auto Setup  
10 Press a/b to select “Complete”, then press  
ENTER.  
11 Press HOME or EXIT to return to the HOME  
screen.  
Change  
Initialize  
To perform other settings, press j.  
For initializing the current setting, select “Initialize”,  
then press ENTER.  
(Continued on the next page)  
51  
 
SETTINGS  
7 Press ENTER, then enter the access point  
name.  
11 Select “Next”, then press ENTER.  
Information on MAC addresses  
12 For testing after confirming the settings, select  
The access point name is manually entered using  
Test”, then press ENTER.  
A MAC address is a unique ID number for  
network equipment. A MAC address is necessary  
for MAC address filtering on the wireless router/  
access point.  
If the test has failed, an error message appears.  
Retry to perform the settings after checking that the  
Enter the access point name.  
Access Point:  
Confirm your setting.  
Before the wireless communication setup is  
performed, we recommend writing down the MAC  
address of the connected wireless LAN adapter  
and keeping it in a safe place. The MAC address  
is labeled on the adapter. (The MAC address is  
displayed on the “Current Ethernet setup info.”  
screen when wireless communication is set (See  
Access Point: XXXXXXXXXXXX  
Security key: XXXXXXXXXXXX  
Next  
Test  
8 Select “Next”, then press ENTER.  
9 Press a/b to select your appropriate security  
13 Follow steps 5–11 of “When selecting Cable”  
settings.  
key, then press ENTER.  
When selecting WPA/WPA2, selectable security  
keys are PSK/TKIP and PSK/AES.  
MAC address  
Select the security key.  
OPEN  
WEP  
WPA-PSK(AES)  
WPA-PSK(TKIP)  
WPA2-PSK(AES)  
WPA2-PSK(TKIP)  
10 Press ENTER, then enter the security key code.  
Enter the exact same security key which has been  
set in the wireless router.  
The security key code is manually entered using the  
Enter the security key.  
Security key:  
Next  
52  
 
SETTINGS  
5 Press D (Yellow) (Complete) to fix the numbers  
NOTE  
The operation procedure for  
inputting characters manually  
which have been input.  
Press j (Del.Char.) to delete a number/  
character you have input.  
To change a number/character you have input, press B  
(Green) (Left) or C (Blue) (Right) to select the number/  
character you want to change, and press j  
(Del.Char.). Then, press c/d to select a new number/  
character you want to input, and press ENTER.  
IP Address  
Netmask  
Gateway  
123  
NOTE  
Numeric characters such as IP address can be entered  
on the input screen either by selecting each of the  
characters in the “Numeric” mode or using the Number  
buttons on the remote control.  
6 Repeat step 1 to 5 to finish inputting all the  
required characters.  
IP Address  
Netmask  
Gateway  
123  
Input character list  
1ABC (Alphabet/  
numeric character)  
1 Press ENTER at the boxes in which characters  
are to be entered, and the input screen will  
appear.  
Num.  
ABC  
DEF  
GHI  
JKL  
MNO  
PQRS  
DEF  
TUV  
WXYZ  
Spc.  
Num. 1 2 3 4 5 6 7 8 9 0 ABC  
a b c A B C  
j k l J K L  
d e f D E F  
GHI  
g h i G H I  
JKL  
TUV  
MNO m n o M N O  
Numeric  
Edit  
PQRS p q r s P Q R S  
t u v T U V  
WXYZ w x y z W X Y Z  
1
2
3
4
5
6
7
8
9
0
Spc.  
(space)  
Numeric  
Sign  
1 2 3 4 5 6 7 8 9 0  
Selected by pressing Selected by pressing  
a/b c/d  
@ . , :  
@ . , :  
; _ - \  
$ % ! ? & # + *  
= / | ˜  
“ ‘ ˆ `  
( ) < >  
[ ]{ }  
Spc.  
2 Press a/b to select the desired input mode.  
3 Press c/d to select a number/character, then  
@ . , :  
; _ - \  
= / | ˜  
; _ - \  
= / | ˜  
$ % ! ? $ % ! ?  
press ENTER.  
& # + * & # + *  
( ) < > ) <  
“ ‘ ˆ `  
Spc.  
“ ‘ ˆ `  
(space)  
4 Repeat the step 3 to display all of the desired  
(
>
[ ]{ }  
[
]
{
}
characters/numbers in the input field.  
Example: The screen for inputting numeric characters  
Edit  
Cancel  
Left  
Right  
Complete  
Del.Char.  
The same operation as the colored buttons and j can be performed by selecting  
each of the items and pressing ENTER.  
“Del.Char.” stands for deleting characters.  
123  
Numeric  
Edit  
1
2
3
4
5
6
7
8
9
0
NOTE  
When performing “Ethernet Setup (Cable)”, only “Numeric” and “Edit” are displayed.  
53  
 
SETTINGS  
5 Press ENTER to move to the next screen.  
Before using the USB device  
6 Press a/b to select “Erase” or “Format”, then  
(USB HDD, USB memory device)  
press ENTER.  
CAUTION:  
Erase: Deletes only BD-VIDEO data written on the  
USB device such as BD-LIVE data.  
Format: Be aware that all data including BD-VIDEO  
data and software update data will be deleted.  
Do not remove the USB device or unplug the AC  
cord while the operations for “USB (HDD/Memory)  
Management” or “Software Update Settings (Manual  
Update from USB memory device)” are being  
performed.  
Do not use a USB extension cable and/or hub when  
connecting a USB device to the player’s USB1 or  
USB2 terminal.  
Erase  
Erases BD-VIDEO data on USB memory.  
Using a USB extension cable and/or hub may  
prevent the player from performing correctly.  
Format  
Erase all contents on USB memory  
including protected contents.  
NOTE:  
SHARP cannot guarantee that all brands’ USB  
devices will operate with this player.  
Only USB memory devices formatted with FAT 32/16  
are compatible.  
When formatting a USB memory device using a PC,  
perform the following settings.  
If you want to delete only the unneeded software  
update data after the software is updated, delete  
the data on the USB device using a PC.  
1 Insert the USB device into the player’s USB  
terminal.  
7 Press a/b to select “Yes”, then press ENTER.  
A confirmation message is displayed. Check that  
the correct USB device is displayed, and then  
continue.  
Format File System: FAT32  
Allocation Unit Size: Default Allocation Size  
See page 18 regarding USB HDD formats.  
Example: Front*  
8 Press a/b to select “USB1” or “USB2”, then  
press ENTER.  
USB (HDD/Memory) Management  
When a wireless LAN adapter is inserted, or only  
one USB device is connected to this player, this  
selection screen does not appear. In such cases,  
after step 7, proceed to step 9.  
The following instructions explain how to delete data  
such as the Virtual Package data and the BD-LIVE  
data in a USB device and also initialize all data in the  
USB device.  
USB device  
9 Start the process.  
A USB terminal is also available on the rear side (USB1  
NOTE  
*
The screen for the current operation will display.  
terminal).  
When you insert or remove a USB device, be sure to  
turn off the main power of this player and the USB  
device (only if connecting a USB HDD) and make sure  
When you perform the “Erase” operation, data which  
has been saved to the player’s internal memory (game  
score, etc.) will also be deleted.  
2 Press POWER to turn on the player.  
3 Press c/d to select “Settings”, then press b or  
Complete  
OK  
ENTER.  
4 Press c/d to select “USB (HDD/Memory)  
Management”, then press b or ENTER.  
The “USB (HDD/Memory) Management” screen is  
displayed.  
10 Press ENTER.  
11 Press HOME or EXIT to exit.  
“No USB Memory” appears when no USB is  
inserted.  
54  
 
SETTINGS  
Update process  
Software Update Settings  
1 When this player is turned on, the Internet  
connection starts automatically.  
In this player, the software version can be updated  
using either one of the following methods.  
Auto Update from Network  
Accessing...” blinks on the screen.  
Manual Update from Network  
Manual Update from USB memory device  
The current version of this unit software and the  
latest version of the update file on the network are  
displayed when latest version of firmware has been  
found.  
Auto Update from Network  
This function allows you to perform the update by  
accessing an Internet connection automatically to  
check if there is a new firmware version every time  
the player is turned on.  
When using this function, it is required to perform  
the following settings in advance.  
To update this player software with update file,  
select “Yes”, and go to step 2.  
Latest version of firmware has been found.  
Firmware update is available.  
Proceed with update?  
Setup  
Current Version :  
Latest Version :  
xxxxxxxxxx  
yyyyyyyyyy  
1 Press c/d to select “Settings”, then press b or  
NOTE  
ENTER.  
If “Yes” will be selected, version update will start.  
Make sure that the LAN cable or the wireless LAN  
adapter is connected to this player and make sure that  
the wireless router/access point is connected to the  
Internet if using the wireless LAN adapter. (See pages  
Make sure to perform the communication settings. (See  
2 Press c/d to select “Software Update  
Yes  
No  
Settings”, then press b or ENTER.  
3 Press a/b to select “Auto Update Setting”,  
then press d or ENTER.  
If the latest firmware version has been already  
updated, nothing is displayed on the screen.  
4 Press a/b to select “Yes”, then press ENTER.  
After this, an Internet connection will be made  
automatically every time this player is turned on.  
It may take time to access and download the update  
depending on the Internet connection and other factors.  
2 Press ENTER to start updating.  
Downloading latest firmware…  
Version : yyyyyyyyyy  
CAUTION  
Do not remove the LAN cable or the wireless LAN  
adapter or unplug the AC cord while downloading or  
updating software.  
30%  
3 When the software is successfully updated, a  
screen is displayed indicating that the update  
process is completed.  
If the update has failed, an error message appears.  
Retry the update after checking if the broadband  
Internetconnection(pages19–20)andcommunication  
settings (pages 50–53) are performed properly.  
4 Press POWER to turn off the player before using  
again.  
55  
   
SETTINGS  
6 Press ENTER to start updating.  
1 Press c/d to select “Settings”, then press b or  
Manual Update from Network  
ENTER.  
Downloading latest firmware…  
Version : yyyyyyyyyy  
2 Press c/d to select “Software Update  
This function allows you to perform the update  
operation by accessing an Internet connection  
manually to check if there is a new firmware version.  
Settings”, then press b or ENTER.  
3 Press a/b to select “Manual Update”, then  
press d or ENTER.  
30%  
NOTE  
4 Press a/b to select “Network”, then press  
Make sure that the LAN cable or the wireless LAN  
adapter is connected to this player and make sure that  
the wireless router/access point is connected to the  
Internet if using the wireless LAN adapter. (See pages  
Make sure to perform the communication settings. (See  
ENTER.  
7 When the software is successfully updated, a  
screen is displayed indicating that the update  
process is completed.  
5 During access to the network and checking the  
latest version of firmware, “Accessing” blinks.  
The current version of this unit software and the  
latest version of the update file on the network are  
displayed when latest version of firmware has been  
found.  
If the update has failed, an error message appears.  
Retry the update after checking if the broadband  
Internetconnection(pages19–20)andcommunication  
settings (pages 50–53) are performed properly.  
It may take time to access and download the update  
depending on the Internet connection and other factors.  
To update this player software with update file,  
select “Yes”, and go to step 6.  
8 Press POWER to turn off the player.  
CAUTION  
Manual Update from USB memory  
device  
Latest version of firmware has been found.  
Firmware update is available.  
Proceed with update?  
Do not remove the LAN cable or the wireless LAN  
adapter or unplug the AC cord while downloading or  
updating software.  
Current Version :  
Latest Version :  
xxxxxxxxxx  
yyyyyyyyyy  
This function allows software updates by inserting  
a USB memory device with the update file into the  
USB1 or USB2 terminal on this player.  
When a software update is performed, the software  
update data must be written onto the USB memory  
device in advance using a PC.  
If “Yes” will be selected, version update will start.  
Yes  
No  
The USB memory device must be clear of all files  
except software update data to allow new software  
uploading.  
If the Internet connection has failed, an error  
message appears.  
Retry the update after checking if the broadband  
Internetconnection(pages19–20)andcommunication  
settings (pages 50–53) are performed properly.  
To check for the availability of a software update,  
you have any questions, please call 1-800-BE-  
SHARP (800-237-4277).  
When software update data is released, copy the data  
onto a USB memory device after downloading it to a  
PC.  
For methods such as downloading and copying to a  
USB memory device, carefully read the description  
shown on the website before performing the operation.  
56  
 
SETTINGS  
When you insert or remove a USB memory device,  
be sure to turn the main power off and make sure  
7 Enter the 4-digit number using 0–9.  
NOTE  
Only USB memory devices formatted with FAT 32/16 are  
compatible.  
When formatting a USB memory device using a PC,  
perform the following settings.  
Enter 4-digit password  
1 Insert the USB memory device with the update  
file into the USB1 or USB2 terminal on this  
player.  
Format File System: FAT32  
Allocation Unit Size: Default Allocation Size  
Do not extract the firmware update file to any folders  
other than the root directory on the USB memory  
device. The firmware update file must be only one file  
directly in the root directory.  
It is recommended that the USB memory device be  
connected to the USB2 terminal on the front of the  
player.  
8 Press ENTER to start checking data in the USB  
memory device.  
Front  
Insert USB memory device containing  
the software update file.  
OK  
9 During the data checking, “Checking” blinks.  
Now checking the data in USB memory device.  
Checking  
USB memory  
device  
USB2 terminal  
2 Press POWER to turn on the power.  
3 Press c/d to select “Settings”, then press b or  
ENTER.  
4 Press c/d to select “Software Update  
Settings”, then press b or ENTER.  
The current version of this unit software and the  
version of the update file on the USB memory  
device are displayed. To update this player software  
with update file, select “Yes”, and press ENTER.  
5 Press a/b to select “Manual Update”, then  
press d or ENTER.  
6 Press a/b to select “USB Memory”, then press  
ENTER.  
Software update file is detected in the USB memory device.  
Start update?  
If you have not yet set the password, go to step 8.  
Current Ver. :  
Update Ver. :  
xxxxxxxxxx  
yyyyyyyyyy  
CAUTION  
Yes  
No  
Do not remove the USB memory device or unplug the  
AC cord while the software is being updated.  
(Continued on the next page)  
57  
SETTINGS  
If the USB memory device is not properly installed  
10 Press ENTER to start updating.  
The screen becomes dark for a while until the  
update screen can be displayed. Please wait for  
the update screen to appear. Do not unplug the AC  
cord.  
11 When the software is successfully updated, a  
screen is displayed indicating that the update  
process is completed.  
or the correct update file cannot be found on  
the USB memory device, an error message is  
displayed.  
Check the file on the USB memory device, and then  
reinsert the USB memory device correctly.  
If the update has failed, check the file in the USB  
device and try Software Update again.  
12 Press POWER to turn off the player.  
Delete unneeded software update data using a PC  
after the software update process is completed.  
The picture will temporarily go dark until  
the software update display appears.  
Wait several minutes and do not unplug the AC cord.  
Software update file is not detected in the USB memory device.  
Confirm that you have transferred the file  
to the USB memory device and retry software update.  
Confirm that you have inserted the USB memory device  
into the correct device.  
13 Remove the USB memory device.  
OK  
OK  
Now updating  
There is more than one software file  
in the USB memory device.  
Confirm that only the software update file is  
in the USB memory device.  
Do not unplug AC cord.  
Update Version  
*
yyyyyyyyyy  
30%  
OK  
About Output of Audio Formats  
HDMI  
DIGITAL OUT  
Maximum number of  
Audio format  
Dolby TrueHD  
channels  
PCM  
7.1ch *3  
5.1ch *3  
7.1ch  
Bitstream  
PCM  
2ch *2  
2ch *2  
2ch *2  
2ch *2  
2ch *2  
2ch *2  
2ch *2  
2ch *2  
Bitstream  
5.1ch *1/*3  
5.1ch *1/*3  
5.1ch *1/*3/*6  
5.1ch *1/*3  
5.1ch *1/*3  
5.1ch *1/*3  
7.1ch (48kHz/96kHz)  
5.1ch (192kHz)  
7.1ch *4  
5.1ch *4  
7.1ch *4  
7.1ch *4  
5.1ch *4  
7.1ch *4  
Dolby Digital Plus  
7.1ch (48kHz)  
DTS-HD Master Audio  
7.1ch (48kHz/96kHz)  
5.1ch (192kHz)  
7.1ch *3  
5.1ch *3/*5  
7.1ch *3  
7.1ch *3  
5.1ch *3  
DTS-HD High Resolution Audio  
LPCM  
7.1ch (48kHz/96kHz)  
7.1ch (48kHz/96kHz)  
5.1ch (192kHz)  
I
Core only  
J
K
L
M
M
N
Down mixed  
When “Secondary Audio” is set to “On”, the audio is output as 48kHz.  
When “Secondary Audio” is set to “On”, the audio is output as PCM.  
When 5.1ch (192kHz), the audio output is downsampled to 96kHz.  
When 2ch, the audio is output as 192kHz.  
58  
 
Streaming content  
Playing back video on demand streaming content  
In this player, you can enjoy a variety of video on  
Playing back  
NOTE  
demand streaming content by connecting to the  
1 Press c/d to select “e-Contents”, then press  
Disc playback and this function cannot be used at the  
same time.  
As the registration process takes time, we recommend  
setting “Auto Power Off” to “No” before starting the  
The streaming quality (SD or HD) depends on the  
network speed and original bit rate of the title.  
netflix.com/help or login to your Netflix account and  
click “Help” at the top of the page.  
Internet.  
b or ENTER.  
Netflix is also available by pressing the NETFLIX  
button on the remote control, and VUDU is also  
available by pressing the VUDU button on the  
Video  
Music  
Picture  
e-Contents  
Settings  
remote control.  
2 Press c/d to select the desired steaming  
content, then press b or ENTER.  
The screen of the streaming content which you  
select is displayed.  
Next  
Netflix is only available in the U.S.  
3 Follow the instruction on the screen.  
4 To exit the screen, press EXIT.  
VOD content  
VOD content  
Netflix  
Instantly Watching Movies  
Instantly Watching Movies from  
Netflix  
VUDU  
Please check that the most current software  
is loaded on this player by using the software  
check for a download of the newest software  
version.  
Enjoying Movies and Internet Application  
YouTube  
Playing back YouTube video content streaming  
NOTE  
To enjoy this function, make a broadband Internet  
connection to both your PC and this player (See pages  
19–20), and then set communication settings (See pages  
To use this function, we recommend setting “Auto  
Power Off” to “No” before starting the registration. (See  
This function allows you to enjoy Netflix through the  
Internet.  
Netflix is an online DVD and Blu-ray Disc rental  
service, offering rental-by mail and streaming  
instantly to Netflix unlimited members.  
Before using this function, please read “Network Service  
The buttons which can be used :  
a/b/c/d / ENTER / a / b /  
c / d / e / j /  
EXIT  
59  
     
Playing back streaming content  
VUDU Customer Care: When you need to talk live  
with someone, contact VUDU Customer Care at  
1-888-554-VUDU (8838) 7 a.m. to 8 p.m. Pacific, 7  
days a week (except holidays).  
NOTE  
Enjoying Movies and Internet  
Application with VUDU  
Your Internet connection is vital to your VUDU  
experience. Please refer to the chart below for minimum  
bandwidth requirements:  
SD (DVD quality): 480p 1 Mbps to 2 Mbps  
HD (HDTV quality): 720p 2.25 Mbps to 4.5 Mbps  
HDX (BD quality): 1080p 4.5 Mbps to 9 Mbps  
VUDU Movies is only available in the U.S.  
For more information on VUDU, visit http://www.VUDU.  
com.  
You can enjoy moves and Internet applications with  
VUDU.  
VUDU Movies is the leading HD on-demand video  
service. VUDU Movies is built into your BD Player  
and utilizes your existing Internet connection  
to deliver the highest quality on-demand video  
available today.  
Operational buttons during playback  
Buttons  
S
d
Description  
Hold down to go in reverse.  
Starts playback.  
Disc playback and this function cannot be used at the  
same time.  
Hold down to fast forward.  
Playback stops.  
V
H
Example  
Troubleshooting - VUDU  
Sets pauses and still pictures.  
F
Pressing quickly once takes you to the  
start of the chapter currently playing.  
Each time you press it, you move back  
to the start of the previous chapter.  
T
VUDU cannot be accessed.  
If you are not able to access other network service (e.g.  
BD-LIVE) from your device, but are not able to access  
VUDU, please contact VUDU Customer Care at 1-888-  
554-VUDU (8838).  
Pressing quickly once takes you to the  
start of the next chapter. Each time you  
press it, you move ahead to the start of  
the next chapter.  
U
If you are not able to access any network service (e.g.  
BD-LIVE) from your device, please contact your device  
manufacture for assistance.  
VUDU Movies features:  
The activation e-mail was not obtained.  
Check your junk or spam e-mail folders. If you are  
unable to find the activation e-mail in the folders,  
reconfirm the e-mail address you have entered, and  
then try your account settings again.  
True 1080p HD, the only service to offer 1080p quality  
video on-demand  
Over 16,000 titles available on-demand  
Over 3,000 titles available in HD, more than are available  
anywhere else  
5.1 surround sound, delivered through state-of-the-art  
Dolby Digital Plus  
The latest Hollywood hits available the same day as  
DVD  
If you encounter any other issues during activation,  
refer to the following online resources:  
Detailed VUDU Manual: Available at  
to all aspects of the revolutionary VUDU service  
with easy-to-follow instructions.  
No subscription fees required  
VUDU FAQ: To learn more about VUDU, visit the  
Frequently Asked Questions at  
60  
 
Playing back streaming content  
Playing back YouTube content  
This player can play back YouTube video content  
streaming through the Internet.  
For more information about YouTube, see the YouTube  
website using a PC (http://www.youtube.com).  
NOTE  
Some video content may not be played back with this  
player.  
The actual functions which can be operated may differ  
from the descriptions shown.  
Operational buttons for playback control  
Item  
Pause the video content. To resume  
playing paused content, press  
the playback controls.  
on  
Skip to the previous video content on  
the video list.  
Skip to the next video content on the  
video list.  
Fast reverse (search).  
Fast forward (search).  
61  
 
Appendix  
PC control of the Player (for BD-AMS20U only)  
This player can be controlled from a PC using the  
Command format  
IP Control Setup  
IP.  
Eight ASCII codes e CR  
Use an ETHERNET cable (commercially available)  
or wireless LAN USB adapter for the connections.  
C1 C2 C3 C4 P1 P2 P3 P4  
NOTE  
Command  
4-digits  
Parameter  
4-digits  
Return code  
This operation system should be used by a person who  
is accustomed to using computers.  
Command 4-digits: Command. The text of four  
characters.  
Communication conditions for IP  
Parameter 4-digits: Parameter 0 – 9, blank  
Connect to the player with the following settings  
1 Press c/d to select “Settings”, then press b or  
made for IP on the PC.  
Parameter  
ENTER.  
Input the parameter values, aligning left, and fill with  
blank(s) for the remainder. (Be sure that four values  
are input for the parameter.)  
IP protocol:  
TCP/IP  
2 Press c/d to select “Communication Setup”,  
then press b or ENTER.  
Host IP address:  
Set the IP address on the player  
menu  
When the input parameter is not within an adjustable  
range, “ERR” returns. (Refer to “Response code  
format”.)  
3 Press a/b to select “IP Control Setup”, then  
press ENTER.  
Service:  
None (Do not select Telnet or  
SSH)  
4 Press a/b to select “Change”, then press  
ENTER.  
Response code format  
TCP port#:  
Set a port number on the player  
menu  
5 To use IP Control, select “Enable”, then press  
Normal response  
ENTER.  
When you set your ID and password on the player  
menu, you need to enter them as soon as you  
connect to the player.  
O
K
6 Set the device name.  
7 Set your login ID and password.  
8 Set the port to use with IP Control.  
9 Confirm the settings, then press “OK”.  
Return code (0DH)  
NOTE  
Problem response (communication error or  
incorrect command)  
The connection will be cut off when there has been no  
communication for 3 minutes.  
Communication procedure  
E
R
R
Send the control commands from the PC via the IP.  
This Player operates according to the received  
command and sends a response message to the  
PC.  
Return code (0DH)  
Do not send multiple commands at the same time.  
Wait until the PC receives the OK response before  
sending the next command.  
Make sure to send “A” with the carriage return and  
confirm that “ERR” returns before operating.  
62  
 
PC control of the Player  
Command list  
CONTROL ITEM  
POWER ON*  
POWER OFF  
PLAY  
COMMAND  
PARAMETER  
CONTROL ITEM  
COMMAND  
PARAMETER  
P
P
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
O
O
P
S
F
W
W
L
R
R
Y
P
D
V
N
K
N
T
1
0
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
PAUSE  
D
D
D
D
B
M
S
I
P
E
U
J
S
T
_
_
_
_
1
1
1
1
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
OPEN/CLOSE  
FUNCTION  
F
N
E
N
R
V
P
C
P
M
D
N
V
STOP  
T
REPEAT  
R
D
N
W
P
FWD  
W
E
DEVICE NAME  
MODEL NAME  
SOFTWARE VERSION  
IP PROTOCOL VERSION  
REV  
R
T
TOP MENU  
UP a  
M
P
U
D
L
W
F
DOWN b  
LEFT c  
R
E
R
E
S
P
S
S
G
N
E
T
RIGHT d  
ENTER  
T
RETURN  
EXIT  
T
X
T
HOME  
E
T
POP-UP MENU  
SKIP K  
SKIP L  
M
K
K
N
B
F
The POWER ON command is available with IP control only when the power is off and  
Quick start is ON.  
*
63  
Troubleshooting  
The following problems do not always suggest a defect or malfunction of this Player.  
Refer to the problems and lists of possible solutions below before calling for service.  
Power  
Problem  
Possible causes and solutions  
The Player power cannot be turned on.  
Is the power cord firmly plugged into the AC outlet? (Page 21)  
When the power cord is plugged into an AC outlet, press and hold POWER on the Player until “  
front panel display. Then, after the POWER indicator is lit, turn on the power. (Page 67)  
” appears on the  
Press POWER after the POWER indicator turns on. (Page 22)  
The Player power is turned off.  
Is “Auto Power Off” set to “Yes”? When “Auto Power Off” is set to “Yes”, the power will be automatically turned off after  
10 continuous minutes of inactivity (no playback). (Page 47)  
Basic Operation  
Problem  
Possible causes and solutions  
The remote control does not work.  
Use the remote control within its operating range. (Page 21)  
Replace the batteries. (Page 21)  
Reset the remote control.  
Press and hold 1 (the number button) first and then ENTER on the remote control together for more than 5 seconds.  
Cannot operate the Player.  
Are you operating the Player within the specified operating temperature range? (Page 69)  
Playback  
Problem  
Possible causes and solutions  
The Player cannot play a disc.  
Take out the disc and clean it. (Page 13)  
Make sure that the disc is loaded properly (aligned in disc tray and label-side up). (Page 26)  
Make sure that region code on the disc matches that of this Player. (Page 9)  
Allow any condensation in or near the Player to dry. (Page 13)  
Check that the disc is recorded in the compatible TV system (PAL or NTSC).  
The Player cannot play back video which was not recorded normally. (Page 10)  
Proper playback may be impossible due to the state of the disc recording, a scratched, warped or dirty disc, the state of  
the pick-up, or compatibility issues between this Player and the disc being used. (Pages 10, 13)  
When the recorded time of a disc is unusually short, playback may not be possible.  
BD-RE/R discs recorded in a format other than BDMV/BDAV cannot be played back. (Page 9)  
The disc is automatically ejected after closing the disc  
tray.  
Make sure that the disc is loaded properly (aligned in disc tray and label-side up). (Page 26)  
Take out the disc and clean it. (Page 13)  
Make sure that the disc is playable. (Page 9)  
64  
Troubleshooting  
Playback (Continued)  
Problem  
Possible causes and solutions  
Video stops.  
Has the Player been subjected to shock or impact? Are you using it in an unstable location? The Player will stop if it  
senses shock or vibration.  
The Player makes a snapping sound when starting  
playback or loading a disc.  
The player may sometimes make a snapping sound when starting playback if it has not been operated in a while. These  
sounds are not malfunctions of the player but are normal operating conditions.  
Picture  
Problem  
Possible causes and solutions  
No picture.  
Make sure that the cable is connected correctly. (Page 16)  
Make sure that the connected TV or the AV receiver is set to the correct input. (Pages 16–17)  
Take out the disc and clean it. (Page 13)  
Make sure that region code on the disc matches that of this Player. (Page 9)  
There is no picture from the HDMI output.  
Are the settings performed correctly? Please check the settings. (Page 46)  
Screen freezes and operation buttons do not work.  
Square noise (mosaic) appears on the screen.  
Turn off the power and turn on the power again.  
If the power is not turned off, perform a reset. (Page 67)  
Is the disc damaged or dirty? Check the condition of the disc. (Page 13)  
Blocks in images may be visible in scenes with rapid movement due to the characteristics of digital image compression  
technology.  
Audio is not output, or images are not played back  
properly.  
The audio may not be output or the images may not be played back properly for some discs in which copyright-  
protected contents are recorded. (Pages 10–11)  
3D images cannot be output to a TV.  
Is an HDMI cable used?  
Are a 3D compatible TV and 3D glasses used?  
Is a proper connection made between the HDMI OUT terminal of the player and the HDMI input terminal of the 3D  
compatible TV? (Page 16)  
Are all devices (amplifier, AV receiver, etc.) between the TV and the player connected by HDMI and 3D compatible?  
(Pages 1617)  
Is the 3D setting on this player correct? (Pages 24, 49)  
Is the 3D setting on the TV correct?  
Is a 3D compatible BD disc being played back?  
Noise appears on the screen.  
When you watch TV broadcasts with the power of this player turned on, noise may appear on the TV screen. In such  
cases, turn off the power to this player or keep this player away from the TV.  
65  
Troubleshooting  
Sound  
Problem  
Possible causes and solutions  
No sound, or sound is distorted.  
If the volume of the TV or amplifier is set to minimum, turn the volume up.  
There is no sound during still mode, slow motion playback, fast forward and fast reverse. (Page 38)  
Check that the HDMI cable and/or optical digital cable is connected correctly. (Page 17)  
Check that the cable plugs are clean.  
Take out the disc and clean it. (Page 13)  
Audio may not be output depending on the audio recording status, such as when audio other than an audio signal or  
non-standard audio is recorded for the audio content of the disc. (Page 10)  
Audio is not output, or images are not played back  
properly.  
The audio may not be output or the images may not be played back properly for some discs in which copyright-  
protected contents are recorded.  
Network  
Problem  
Possible causes and solutions  
Cannot connect to the Internet.  
When the wired Internet connection is made  
Is the LAN cable connected properly? (Page 19)  
Is the wrong cable such as a modular cable used? Connect a LAN cable to the ETHERNET terminal. (Page 19)  
Is the power for the connected equipment, such as a broadband router or modem turned on?  
Is the broadband router and/or modem properly connected?  
Is the proper value(s) set in the network setting? Check “Communication Setup”. (Pages 50–53)  
When the wireless Internet connection is made  
Is the wireless LAN adapter connected properly? (Page 20)  
Is the power for the connected equipment, such as a wireless router or access point turned on?  
Is the wireless router or access point properly connected?  
Are there any obstacles, such as physical structures (brick and concrete walls, etc.) and electronics (microwave, etc.)  
between the wireless router/access point and the player? As this may cause interference with the wireless signal, make  
sure to keep obstacles away.  
Is the proper value(s) set in the network setting? Check “Communication Setup”. (Pages 50–53)  
Cannot download BD-LIVE contents.  
Is the LAN cable or the wireless LAN adapter connected properly? (Pages 19–20)  
Is the USB device properly connected? Check that the USB device is connected to the USB1 or USB2 terminal of this  
Player. (Page 28)  
Check if the BD disc supports BD-LIVE.  
Check the setting for “BD Internet Access”. (Page 48)  
66  
Troubleshooting  
Other  
Problem  
Possible causes and solutions  
The TV operates incorrectly.  
Some TVs with wireless remote control capability may operate incorrectly when using the remote control of this Player.  
Use such TVs away from this Player.  
The Player heats up during use.  
When using this Player, the console cabinet may heat up depending on the usage environment. This is not a malfunction.  
POWER (ON/STANDBY) indicator will remain lit.  
When the AC cord is removed from the outlet, the POWER (ON/STANDBY) indicator will remain lit for a short period. This  
is normal and is not a malfunction.  
POWER  
To Reset this Player  
If this Player receives strong interference from a source such as excessive static electricity, strong external noise, malfunction of power supply, or  
voltage caused by lightning during use or a wrong operation is sent to the Player, errors like the Player not accepting an operation may occur.  
Press and hold POWER on the Player until “  
” appears on the front panel display when the Player does not operate properly even after  
the power has been turned off. Then, after the POWER indicator is lit, turn on the power.  
When a reset is performed while the power is on, the Player will turn off. Turn the power on again. At this point, it may take a few moments for the system processing to finish before  
the Player is ready for use. During the system processing, the BD/DVD/CD mode indicator on the front panel display of the player will blink. Once the system processing has finished,  
the indicator will finish blinking and then light up normally. You can operate the Player when the BD/DVD/CD mode indicator is lit.  
Since all settings including the language setting stored in memory are also reset when a reset has been performed, they must be set again.  
When the problem persists even after performing a reset, unplug the AC cord and plug it in again. If this does not solve the problem, contact the nearest service center approved by  
SHARP.  
67  
 
On-screen Error Messages  
The following messages appear on the TV screen in case of an error during operation.  
Error message  
Possible Error  
Suggested Solution  
Cannot play.  
The disc cannot be played back with this Player.  
Check the disc, and load it correctly.  
Incompatible disc.  
If you load a disc which cannot be played with this  
Player (i.e. a scratched disc), or if you load a disc upside  
down, this message will appear, and the disc tray will  
automatically pop out.  
Occurs if the loaded disc cannot be played because it is Remove the disc.  
a non-standard disc or scratched, etc.  
Cannot operate.  
Occurs if an operation is incorrect.  
This USB memory is not formatted properly. Please format Occurs if there is a formatting error.  
the memory in USB memory management. Occurs if the USB memory is not formatted with FAT  
32/16.  
Format the USB memory again.  
Format the USB memory with your PC.  
The Connected USB Memory cannot be used. It should be Occurs if USB memory not compliant with USB 2.0 High Connect USB 2.0 High Speed (480 Mbps) compliant  
compliant with USB 2.0  
Speed (480 Mbps) is used (i.e. USB 1.0/USB 1.1).  
USB memory.  
NOTE  
Cinavia Notice  
This product uses Cinavia technology to limit the use of unauthorized copies of some  
commercially-produced film and videos and their soundtracks. When a prohibited use  
of an unauthorized copy is detected, a message will be displayed and playback or  
copying will be interrupted.  
More information about Cinavia technology is provided at the Cinavia Online Consumer  
Information Center at http://www.cinavia.com. To request additional information about  
Cinavia by mail, send a postcard with your mailing address to: Cinavia Consumer  
Information Center, P.O. Box 86851, San Diego, CA, 92138, USA.  
68  
Specifications  
Specifications are subject to change without notice.  
General  
Power supply  
AC 120 V, 60 Hz  
BD-AMS10U 15 W  
BD-AMS20U 16 W  
Power consumption (Normal)  
Power consumption (Standby)  
Dimensions  
BD-AMS10U Approx. 0.1 W (When “Quick Start” is set to “No”)  
BD-AMS20U Approx. 0.2 W (When “Quick Start” is set to “No”)  
Approx. 16 15 16 g 1 15 16 g 7 1/16 inch (W g H g D)  
/ /  
Approx. 430 mm g 49 mm g 178 mm (W g H g D)  
Weight  
Approx. 3.3 lbs. (1.5 kg)  
Operating temperature  
Storage temperature  
Operating humidity  
TV systems  
41°F to 95°F (5°C to 35°C)  
–4°F to 140°F (–20°C to 60°C)  
10 % to 80 % (no condensation)  
NTSC system  
Playback  
Playable discs/media formats  
BD-ROM, BD-RE, BD-R,  
DVD Video, DVD+RW/+R/-RW/-R (Video/VR/AVCHD/JPEG file/MP3 file/DivX (H.264/MKV) format),  
Audio CD (CD-DA), CD-RW/R (CD-DA/JPEG file/MP3 file format)  
USB device (USB HDD, USB memory device) (JPEG file/MP3 file/DivX (H.264/MKV) format)  
Region code  
A or ALL for BD, 1 or ALL for DVD  
Input/Output  
HDMI output  
HDMI 19-pin standard connector (1080p 24Hz output)  
HDMI® (Deep Color, x.v.Color, Dolby TrueHD, DTS-HD Master Audio | Essential)  
HDMI (MHL) input (for BD-AMS20U only)  
For a MHL device  
HDMI 19-pin standard connector  
Digital audio optical output  
USB input  
Terminal: Square Optical terminal  
USB1/USB2  
USB 2.0 High Speed (480 Mbps) correspondence (for Wireless LAN adapter and Local storage/Software update/JPEG,  
MP3 and DivX (H.264/MKV) playback)  
ETHERNET  
10BASE-T/100BASE-TX  
69  
 
Specifications  
Wireless LAN USB Adapter (for BD-AMS20U only)  
Product name  
Standard  
Wireless LAN adapter (supplied)  
IEEE 802.11b/g/n  
USB 2.0  
Host interface  
Frequency band  
Draft 802.11n Radio: 2.4GHz  
802.11g Radio: 2.4GHz  
802.11b Radio: 2.4GHz  
2.400 – 2.483GHz (channel 1–11)  
Modulation  
DBPSK @ 1 Mbps  
DQPSK@ 2 Mbps  
CCK@ 5.5/11 Mbps  
BPSK@ 6/9 Mbps  
QPSK@ 12/18 Mbps  
16-QAM@ 24/36 Mbps  
64-QAM@ 48/54 Mbps  
Security  
AP (Infrastructure) mode supports  
- Static WEP that supports both 64 and 128 bit keys.  
- WPA(TKIP) with PSK  
Power consumption  
Dimensions  
TX: up to 310mA (5V)  
Approx. 11  
/
16  
g
11  
/
32 g 13/16 inch (W g H g D)  
Approx. 17 g 8.4 g 29.8 mm (W g H g D)  
Weight  
Approx. 0.14 oz (3.9 g)  
Information on Disposal for Users (private households)  
1. In the European Union  
Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin!  
Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires proper treatment, recovery and recycling of used electrical and  
electronic equipment. Following the implementation by member states, private households within the EU states may return their used electrical and electronic equipment to designated  
collection facilities free of charge*. In some countries* your local retailer may also take back your old product free of charge if you purchase a similar new one.  
*) Please contact your local authority for further details.  
The wireless LAN adapter (supplied with  
BD-AMS20U only) is marked with this  
symbol. It means that used electrical and  
electronic products should not be mixed  
with general household waste. There is  
a separate collection system for these  
products.  
Please contact your local authority for  
the correct method of disposal of this  
product and/or packaging.  
If your used electrical or electronic equipment has batteries or accumulators, please dispose of these separately beforehand according to local requirements.  
By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the  
environment and human health which could otherwise arise due to inappropriate waste handling.  
2. In other Countries outside the EU  
If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.  
70  
Glossary  
This Player is compatible with Deep Color. You can  
enjoy this function by connecting to a Deep Color  
compatible TV using an HDMI cable.  
Ad-hoc mode is a wireless LAN communication  
format. This performs direct communication  
between equipment without an access point. (Ad-  
hoc mode is not supported.)  
A BD-RE (Blu-ray Disc Rewritable) is a recordable  
and rewritable Blu-ray Disc.  
BD-ROM  
This lets you select things like the subtitle language  
or audio format using a menu stored on the DVD  
video disc.  
BD-ROMs (Blu-ray Disc Read-Only Memory)  
are commercially produced discs. Other than  
conventional movie and video contents, these discs  
have enhanced features such as interactive content,  
menu operations using pop-up menus, selection of  
subtitle display, and slide shows. Although a BD-  
ROM may contain any form of data, most BD-ROM  
discs will contain movies in High Definition format  
for playback on Blu-ray Disc players.  
AVCHD (Advanced Video Codec High Definition)  
refers to a recording format (specification) for digital  
video cameras which can record to a disc such as  
8 cm DVD disc and play back digital high definition  
images.  
Dolby Digital  
A sound system developed by Dolby Laboratories  
Inc. that gives movie theater ambience to audio  
output when the product is connected to a Dolby  
Digital processor or amplifier.  
BDAV (Blu-ray Disc Audio/Visual, BD-AV) refers to  
one of the application formats used for writable  
Blu-ray discs such as BD-R, BD-RE, etc. BDAV is a  
recording format equivalent to DVD-VR (VR mode) of  
the DVD specifications.  
A sound system developed as an extension to Dolby  
Digital. This audio coding technology supports 7.1  
multi-channel surround sound.  
A disc format developed for recording/playing high-  
definition (HD) video (for HDTV, etc.), and for storing  
large amounts of data. A single layer Blu-ray Disc  
holds up to 25 GB, and a dual-layer Blu-ray Disc  
holds up to 50 GB of data.  
BD-J application  
Dolby TrueHD is a lossless coding technology that  
supports up to 8 channels of multi-channel surround  
sound for the next generation optical discs. The  
reproduced sound is true to the original source bit-  
for-bit.  
The BD-ROM format supports Java for interactive  
functions. “BD-J” offers content providers almost  
unlimited functionality when creating interactive BD-  
ROM titles.  
Sections of a movie or a music feature that are  
smaller than titles. A title is composed of several  
chapters. Some discs may only be comprised of a  
single chapter.  
DTS  
A variety of interactive content is available from BD-  
LIVE compatible Blu-ray discs via the Internet.  
This is a digital sound system developed by DTS,  
Inc. for use in cinemas.  
This function allows you to operate this player using  
the TV remote control by displaying the control  
panel on the TV screen.  
DTS-HD High Resolution Audio is a new technology  
developed for the next generation high definition  
optical disc format.  
BDMV (Blu-ray Disc Movie, BD-MV) refers to one  
of the application formats used for BD-ROM which  
is one of the Blu-ray Disc specifications. BDMV is  
a recording format equivalent to DVD-video of the  
DVD specification.  
Copy guard  
This function prevents copying. You cannot copy  
discs marked by the copyright holder with a signal  
which prevents copying.  
DTS-HD Master Audio is a lossless audio  
compression technology developed for the next  
generation high definition optical disc format.  
A BD-R (Blu-ray Disc Recordable) is a recordable,  
write-once Blu-ray Disc. Since contents can be  
recorded and cannot be overwritten, a BD-R can be  
used to archive data or for storing and distributing  
video material.  
Deep Color  
Deep Color can reproduce rich colors, increasing  
the number of bits describing colors.  
(Continued on the next page)  
71  
Glossary  
DTS-HD Master Audio | Essential  
Linear PCM Sound  
DTS-HD Master Audio | Essential is a lossless audio  
compression technology developed for the next  
generation high definition optical disc format.  
A DVD+/-RW is a recordable and rewritable DVD.  
The re-recordable feature makes editing possible.  
The DVD+/-RW has two different formats: VR format  
and Video format. DVDs created in Video format  
have the same format as a DVD video, while discs  
created in VR (Video Recording) format allow the  
contents to be programed or edited.  
Linear PCM is a signal recording format used for  
Audio CDs and on some DVD and Blu-ray discs. The  
sound on Audio CDs is recorded at 44.1 kHz with  
16 bits. (Sound is recorded between 48 kHz with 16  
bits and 96 kHz with 24 bits on DVD video discs and  
between 48 kHz with 16 bits and 192 kHz with 24  
bits on BD video discs.)  
Upscaling (upconverting) refers to a function of  
various players and devices that enlarge the image  
size to fit the size of the screen of video equipments  
such as a TV.  
MHL (Mobile High-definition Link) (page  
HDMI (High-Definition Multimedia Interface) is an  
interface that supports both video and audio on  
a single digital connection. The HDMI connection  
carries standard to high definition video signals  
and multi-channel audio signals to AV components  
such as HDMI equipped TVs, in digital form without  
degradation.  
MHL is a mobile audio and video interface standard  
for transmitting digital audio and high definition (HD)  
video (1080p/30fps) without any compression.  
A disc format that contains up to eight hours of  
moving pictures on a disc the same diameter as  
a CD. A single-layer single sided DVD holds up to  
4.7 GB; a double layer single-sided DVD, 8.5 GB; a  
single layer double-sided DVD, 9.4 GB; double-layer  
double-sided DVD, 17 GB. The MPEG 2 format was  
adopted for efficient video data compression. It is  
a variable rate technology that encodes the data to  
according to the status of the video for reproducing  
high-quality images. Audio information is recorded  
in a multi-channel format such as Dolby Digital,  
allowing for a realistic audio presence.  
MP3 files are audio data compressed in the  
MPEG1/2 Audio layer-3 file format. “MP3 files” have  
“.mp3” as extensions.  
Infrastructure mode (page 20)  
Infrastructure mode is a wireless LAN  
communication format. This performs wireless  
communication through an access point.  
MPEG-2  
MPEG-2 (Moving Picture Experts Group phase 2) is  
one of the video data compression schemes, which  
is adopted for DVD videos and digital broadcasts  
worldwide. Some Blu-ray Discs also use high bitrate  
MPEG-2.  
Interlace format  
Interlace format shows every other line of an image  
as a single “field” and is the standard method for  
displaying images on television. The even numbered  
field shows the even numbered lines of an image,  
and the odd numbered field shows the odd  
numbered lines of an image.  
A DVD+/-R is a recordable, write-once DVD.  
Since contents can be recorded and cannot be  
overwritten, a DVD+/-R can be used to archive data  
or for storing and distributing video material. The  
DVD+/-R has two different formats: VR format and  
Video format. DVDs created in Video format have  
the same format as a DVD video, while discs created  
in VR (Video Recording) format allow the contents to  
be programed or edited.  
This is a feature of DVD and BD video discs. In  
some discs, the same scene is shot from different  
angles, and these are stored in a single disc so you  
can enjoy playback from each angle. (This function  
can be enjoyed if the disc is recorded with multiple  
angles.)  
JPEG (Joint Photographic Experts Group) is a still  
image data compression format and is used in most  
of digital cameras.  
Multi Audio  
This is a feature of DVD and BD video discs. This  
function makes it possible to record different audio  
tracks for the same video, so you can enhance your  
enjoyment by switching the audio. (You can enjoy  
this function with discs recorded with multiple audio  
tracks.)  
72  
Glossary  
Netflix is an online DVD and Blu-ray Disc rental  
service, offering rental-by mail and streaming  
instantly to Netflix unlimited members.  
These are the lines of text appearing at the bottom  
of the screen which translate or transcribe the  
dialog. They are recorded on many DVD and BD  
video discs.  
Parental control (page 48)  
In some digital broadcasts and BD/DVD video discs,  
a control level for disc viewing is set depending on  
the age of the viewer. With this Player, you can set  
the control level for viewing such broadcasts and  
discs.  
Time number  
This indicates the play time which has elapsed from  
the start of a disc or a title. It can be used to find a  
specific scene quickly. (It may not work with some  
discs.)  
An enhanced menu operation available on BD video  
discs. The pop-up menu appears when POP-UP  
MENU is pressed during playback, and can be  
operated while playback is in progress.  
These numbers are recorded on DVD and Blu-ray  
discs. When a disc contains two or more movies,  
these movies are numbered as title 1, title 2, etc.  
Progressive format  
In a BD/DVD video, this is the menu for selecting  
things like the chapter to be played back and the  
subtitle language. In some DVD videos, the top  
menu may be called the “Title Menu”.  
Compared to the Interlace format that alternately  
shows every other line of an image (field) to create  
one frame, the Progressive format shows the entire  
image at once as a single frame. This means that  
while the Interlace format can show 30 frames/60  
fields in one second, the Progressive format  
can show 60 frames in one second. The overall  
picture quality increases and still images, text, and  
horizontal lines appear sharper.  
These numbers are assigned to the tracks which are  
recorded on audio CDs. They enable specific tracks  
to be located quickly.  
VUDU is an on-demand video service for renting or  
buying movies that can be watched instantly on TV.  
Code identifying a geographic region of  
compatibility for a BD/DVD.  
x.v.Color  
x.v.Color reproduces a greater range of color than  
before, showing almost all of the colors that the  
human eye can detect. (Applicable for JPEG files  
only with this system)  
If you stop playback while it is in progress, the  
Player stores the stop position in memory, and this  
function lets you playback from that point.  
YouTube is a website where users can upload and  
view video content, such as video clips and TV clips.  
You can watch the content streamed on your TV.  
This returns to the start of the chapter (or track)  
being played, or skips to the next chapter (or track).  
73  
Network Service Disclaimer  
This Sharp device facilitates the access to content and services provided by third parties. The content and services accessible via this device belong to and may  
be proprietary to third parties. Therefore, any use of such third party content and services must be in accordance with any authorization or terms of use provided by  
such content or service provider. Sharp shall not be liable to you or any third party for your failure to abide by such authorization or terms of use. Unless otherwise  
specifically authorized by the applicable content or service provider, all third party content and services provided are for personal and non-commercial use; you may  
not modify, copy, distribute, transmit, display, perform, reproduce, upload, publish, license, create derivative works from, transfer or sell in any manner or medium any  
content or services available via this device.  
Sharp is not responsible, nor liable, for customer service-related issues related to the third party content or services. Any questions, comments or service-related  
inquiries relating to the third party content or service should be made directly to the applicable content or service provider.  
You may not be able to access content or services from the device for a variety of reasons which may be unrelated to the device itself, including, but not limited to,  
power failure, other Internet connection, or failure to configure your device properly. Sharp, its directors, officers, employees, agents, contractors and affiliates shall  
not be liable to you or any third party with respect to such failures or maintenance outages, regardless of cause or whether or not it could have been avoided.  
ALL THIRD PARTY CONTENT OR SERVICES ACCESSIBLE VIA THIS DEVICE IS PROVIDED TO YOU ON AN “AS-IS” AND “AS AVAILABLE” BASIS AND SHARP AND  
ITS AFFILIATES MAKE NO WARRANTY OR REPRESENTATION OF ANY KIND TO YOU, EITHER EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY  
WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT, FITNESS FOR A PARTICULAR PURPOSE OR ANY WARRANTIES OF SUITABILITY, AVAILABILITY,  
ACCURACY, COMPLETENESS, SECURITY, TITLE, USEFULNESS, LACK OF NEGLIGENCE OR ERROR-FREE OR UNINTERRUPTED OPERATION OR USE OF THE  
CONTENT OR SERVICES PROVIDED TO YOU OR THAT THE CONTENT OR SERVICES WILL MEET YOUR REQUIREMENTS OR EXPECTATIONS.  
SHARP IS NOT AN AGENT OF AND ASSUMES NO RESPONSIBILITY FOR THE ACTS OR OMISSIONS OF THIRD PARTY CONTENT OR SERVICE PROVIDERS, NOR  
ANY ASPECT OF THE CONTENT OR SERVICE RELATED TO SUCH THIRD PARTY PROVIDERS.  
IN NO EVENT WILL SHARP AND/OR ITS AFFILIATES BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, PUNITIVE,  
CONSEQUENTIAL OR OTHER DAMAGES, WHETHER THE THEORY OF LIABILITY IS BASED ON CONTRACT, TORT, NEGLIGENCE, BREACH OF WARRANTY,  
STRICT LIABILITY OR OTHERWISE AND WHETHER OR NOT SHARP AND/OR ITS AFFILIATES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.  
74  
 
About Software License  
Information on the Software License for This Product  
Software composition  
The software included in this product is comprised of various software components whose individual copyrights are held by SHARP or by third parties.  
Software developed by SHARP and open source software  
The copyrights for the software components and various relevant documents included with this product that were developed or written by SHARP are owned  
by SHARP and are protected by the Copyright Act, international treaties, and other relevant laws. This product also makes use of freely distributed software and  
software components whose copyrights are held by third parties. These include software components covered by a GNU General Public License (hereafter GPL), a  
GNU Lesser General Public License (hereafter LGPL) or other license agreement.  
Obtaining source code  
Some of the open source software licensors require the distributor to provide the source code with the executable software components. GPL and LGPL include  
similar requirements. For information on obtaining the source code for the open source software and for obtaining the GPL, LGPL, and other license agreement  
information, visit the following website:  
We are unable to answer any questions about the source code for the open source software. The source code for the software components whose copyrights are  
held by SHARP is not distributed.  
Acknowledgements  
The following open source software components are included in this product:  
• cairo • Curl • DirectFB • Droid Sans font • Droid Sans Fallback font • Expat • Fltk • FreeType • Giflib • glib • Icu • Jpeg • libcurl • libidn  
• Libpng • LibPThread • Librt • libsoup • libssl and libcrypto • Libstdc++ • libxml2 • lua • lua-slncryptop • lua-xmlreader • OpenSSL  
• Optional UnitTest++ Software • pango • swfdec • Webkit • zlib • linux kernel • uClibc • modutils • NanoXML • org.apache.oro.text.regex  
• libsysfs • mtd/jffs2 • ncurses • Qt/Webkit • libiconv • libusb • busybox • bash • libmpeg2 • libjpeg • FontConfig • ntfs-3g  
Software License Notice  
Software License Notice Requirements  
The software components incorporated into this product include components whose copyright holders require license notices. The license notices for these software  
components are shown below.  
OpenSSL License  
This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org)  
Original SSLeay License  
This product includes cryptographic software written by Eric Young ([email protected]).  
BSD License  
This product includes software developed by the University of California, Berkeley and its contributors.  
75  
LIMITED WARRANTY  
CONSUMER LIMITED WARRANTY  
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”), when shipped in its original container, will be free  
from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured  
equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.  
This warranty does not apply to any appearance items of the Product or if the serial number or model number affixed to the Product has been removed, defaced, changed, altered or  
tampered with. This warranty does not cover installation or signal reception problems. This limited warranty will not apply if the Product has been or is being used in a commercial  
setting or application; this warranty is meant solely for the non-commercial, household use of the Product by consumers in their home or residence.  
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer.  
To the extent permitted by applicable state law, the warranties set forth are in lieu of, and exclusive of, all other warranties, express or implied. Specifically ALL OTHER WARRANTIES  
OTHER THAN THOSE SET FORTH ABOVE ARE EXCLUDED, ALL EXPRESS AND IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS  
FOR USE, AND FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED. IF, UNDER APPLICABLE STATE LAW, IMPLIED WARRANTIES MAY NOT VALIDLY BE  
DISCLAIMED OR EXCLUDED, THE DURATION OF SUCH IMPLIED WARRANTIES IS LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. THIS  
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.  
The warranties given herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser and only for the time  
periods set forth herein. No other representations or promises made by anyone are permitted. Correction of defects, in the manner and for the period of time described herein, shall  
constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether  
based on contract, negligence, strict liability or otherwise. Sharp does not warrant nor shall Sharp be liable, or in any way responsible, for Products which have been subject to  
abuse (including, but not limited to, improper voltage), accident, misuse, negligence, lack of reasonable care, alteration, modification, tampering, improper operation or maintenance  
or any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than a Sharp authorized servicer. Nor shall Sharp be liable  
or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow limits on warranties or on remedies for breach in certain  
transactions; in such states, the limits herein may not apply.  
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND PUERTO RICO.  
Model Specific Section  
Your Product Model Number & Description:  
BD-AMS10U BLU-RAY DISC/DVD PLAYER  
BD-AMS20U BLU-RAY DISC/DVD PLAYER  
(Be sure to have this information available when you need service for your Product.)  
Warranty Period for this Product:  
One (1) year parts and labor from the date of purchase.  
Non-rechargeable batteries.  
Additional Item(s) Excluded from  
Warranty Coverage (if any):  
Where to Obtain Service:  
From a Sharp Authorized Servicer located in the United States. To find the location of the nearest Sharp Authorized Servicer,  
call Sharp toll free at 1-800-BE-SHARP.  
What to do to Obtain Service:  
Please transport the Product in its original packaging and ensure that the Product is covered to avoid scratches and  
damage. Sharp shall not be responsible for lost, stolen or misdirected mail or for damage to the product incurred during  
shipping.  
TO OBTAIN PRODUCT INFORMATION, CALL 1-800-BE-SHARP OR VISIT www.sharpusa.com  
76  
LIMITED WARRANTY  
LIMITED WARRANTY  
Consumer Electronics Products  
Congratulations on your purchase!  
Sharp Electronics of Canada Ltd. (“Sharp”) warrants to the first purchaser for this Sharp brand product (“Product”), when shipped in its original container and sold or  
distributed in Canada by Sharp or by an authorized Sharp dealer, that the Product will during the applicable warranty period, be free from defects in material and  
workmanship, and will within the applicable warranty period, either repair the defective Product or provide the first purchaser a replacement of the defective Product.  
(a) Any defects caused or repairs required as a result of abusive operation, negligence, accident, improper installation or inappropriate use as outlined in the owner’s  
manual or other applicable Product documentation.  
(b) Any defects caused or repairs required as a result of any Product that has been tampered with, modified, adjusted or repaired by any person other than Sharp, a  
Sharp authorized service centre or a Sharp authorized servicing dealer.  
(c) Any defects caused or repairs required as a result of the use of the Product with items not specified or approved by Sharp, including but not limited to, head  
cleaning tapes and chemical cleaning agents.  
(d) Any replacement of accessories, glassware, consumable or peripheral items required through normal use of the Product, including but not limited to, earphones,  
remote controls, AC adapters, batteries, temperature probe, trays, filters, belts, ribbons, cables and paper.  
(e) Any cosmetic damage to the Product surface or exterior that has been defaced or caused by normal wear and tear.  
(f) Any defects caused or repairs required as a result of damage caused by any external or environmental conditions, including but not limited to, transmission  
line/power line voltage or liquid spillage or acts of God.  
(g) Warranty claims for Products returned with illegible or without appropriate model, serial number and CSA/cUL markings.  
(h) Any Products used for rental or commercial purposes.  
(i) Any installation, setup and/or programming charges.  
How to get service: Warranty service may be obtained upon delivery of the Product, together with proof of purchase (including date of purchase) and a copy of this  
limited warranty statement, to an authorized Sharp service centre or an authorized Sharp servicing dealer. In home warranty service may be provided, at Sharp’s  
discretion, on any Sharp Television with the screen size of 40” or larger and on any Sharp Over-The-Range Microwave Oven or Home Use Microwave Drawer . No  
other person (including any Sharp dealer or service centre) is authorized to extend, enlarge or transfer this warranty on behalf of Sharp. The purchaser will be  
responsible for any and all removal, reinstallation, transportation and insurance costs incurred.  
The express warranties in this limited warranty are, except for consumer purchasers domiciled in Quebec, in lieu of and, except to the extent prohibited by applicable  
law, Sharp disclaims all other warranties and conditions, express or implied, whether arising by law, statute, by course of dealing or usage of trade, including, without  
limitation, implied warranties or conditions of merchantability and/or quality, fitness for a particular use or purpose, and/or non-infringement. Limitations (not  
applicable to consumer purchasers domiciled in Quebec to the extent prohibited under Quebec law): (a) Sharp shall not be liable for any incidental, special, conse-  
quential, economic, exemplary or indirect damages of any kind or nature (including lost profits or damages for loss of time or loss of use or loss of data) arising from  
or in any connection with the use or performance of a Product or a failure of a Product, even if Sharp is aware of or has been advised of the possibility of such  
damages; (b) the remedies described in this limited warranty constitute complete fulfillment of all obligations and responsibilities of Sharp to the purchaser with  
respect to the Product and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. Some provinces may not  
allow the exclusion or limitation of certain damages, or limits on the duration or voiding of implied warranties or conditions; in such provinces, the exclusions and  
limits herein may not apply. This limited warranty is, except for consumer purchasers domiciled in Quebec, governed by the laws of the Province in Canada in which  
the purchaser has purchased the Product. For consumer purchasers domiciled in Quebec this limited warranty is governed by the laws of Quebec.  
WARRANTY PERIODS (calculated from the date of original purchase):  
Audio Product  
BD/DVD Product  
Projector  
1 year  
Air Purifier  
1 year  
1 year  
1 year  
1 year  
1 year  
1 year  
Portable Air Conditioner  
Plasmacluster Ion Generator  
3D Glasses  
1 year (lamp 90 days)  
1 year  
1 year (magnetron component-4 additional years) Wireless LAN Adapter  
LCD TV  
Microwave Open  
To obtain the name and address of the nearest Authorized Sharp Service Centre or Dealer, or for more information on this Limited Warranty, Sharp Extended Warranty Offers,  
Sharp Canada Products or Accessory Sales, please contact Sharp:  
• By writing to Sharp Electronics Of Canada Ltd. at 335 Britannia Road East Mississauga, Ontario L4Z 1W9  
• Calling: at 905-568-7140  
THIS LIMITED WARRANTY IS VALID ONLY IN CANADA  
Revision 12/17/10  
77  
 
SHARP ELECTRONICS CORPORATION  
Sharp Plaza, Mahwah, New Jersey 07495-1163  
SHARP CORPORATION  
12P02-CH-NG  

Vita Mix 748 User Manual
Toshiba TEC FDS 50 User Manual
Toshiba MA 1595 1 User Manual
Sony XCG V60E User Manual
Sony PC55E User Manual
Sony HANDYCAM SR38E User Manual
Sony DSR45P User Manual
Sony Bluetooth Stereo Earset DRBT140Q User Manual
Slick SIMPLEFLIX VC130 User Manual
Samsung AK68 01859B User Manual