Samsung Camcorder SCB 2000N User Manual

Ultra High Resolution Camera SCB-2000 User Guide  
Before installing and operating this product,  
please read this manual thoroughly.  
ENGLISH  
Thank you for purchasing a SAMSUNG CCD CAMERA.  
Before operating the camera, confirm the camera model and correct input  
power voltage. In order to that you can understand this manual thoroughly,  
we will explain the model pert numbers.  
n SCB-2000 SERIES  
• NTSC MODEL  
SCB-2000N  
• PAL MODEL  
SCB-2000P  
SCB-2000ND  
SCB-2000PD  
SCB-2000PH  
The lightning flash with an arrowhead symbol, within an equilateral triangle is  
intended to alert the user to the presence of uninsulated “dangerous voltage”  
within the product's enclosure that may be of sufficient magnitude to constitute  
a risk of electric shock to persons.  
n MODEL DESCRIPTION  
• SCB-2000XX  
__  
POWER SOURCE  
SIGNAL SYSTEM  
The exclamation point within an equilateral triangle is intended to alert the user  
to the presence of important operating and maintenance (servicing) instructions  
in the literature accompanying the appliance.  
• SIGNAL SYSTEM  
N NTSC MODEL  
P PAL MODEL  
INFORMATION-This equipment has been tested and found to comply with  
limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These  
limits are designed to provide reasonable protection against harmful  
interference when the equipment is operated in a commercial environment.  
This equipment generates, uses, and can radiate radio frequency energy and,  
if not installed and used in accordance with the instruction manual, may  
cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful  
interference in which case the user will be required to correct the interference  
at his own expense.  
• POWER SOURCE  
AC 24V / DC 12V  
D DC 12V  
H AC 230V  
WARNING : Changes or modifications not expressly approved by the  
manufacturer could void the user’s authority to operate the equipment.  
WARNING : To prevent electric shock and risk of fire hazards:  
Do NOT use power sources other than that specified.  
Do NOT expose this appliance to rain or moisture.  
This installation should be made by a qualified service person and  
should conform to all local codes.  
Contents  
Features  
SSDR  
Features ………………………………………………………………………… 5  
Warnings & Cautions ……………………………………………………… 6  
Precautions …………………………………………………………………… 7  
Components and Accessories …………………………………………… 8  
Overview………………………………………………………………………… 9  
Installation …………………………………………………………………… 10  
High Resolution  
(Samsung Super Dynamic Range)  
For images with high contrast between  
bright and dark areas from difficult lighting  
conditions such as backlighting, this camera  
selectively illuminates darker areas while  
retaining the same light level for brighter  
areas to even out the overall brightness.  
By adopting a diagonal 6mm(1/3") 410,000  
(NTSC) pixel, 470,000(PAL) pixel SONY CCD,  
the camera produces clear picture quality with  
a horizontal resolution of 600 TV lines for color.  
Excellent Sensitivity  
DIS (Digital Image Stabilizer)  
The DIS function compensates for any camera  
movement, to produce more stable pictures.  
The built-in high sensitivity COLOR CCD  
produces a clear image even in  
0.05Lux(COLOR), 0.0001Lux(SENS-UP) or  
lower illumination.  
n
LENS……………………………………………………………………………………… …10…  
n Connecting to the Monitor………………………………………………………… …12…  
n Using Coaxial Communications…………………………………………………… …13…  
n Connecting to the Power…………………………………………………………… …14  
Video/DC Drive Lens Support  
SSNR3 (Samsung Super Noise  
Reduction) Function  
You can select Video or DC Drive Lens from  
the menu.  
Operating your Camera …………………………………………………… 15  
n Menu Configuration…………………………………………………………………… …15…  
n Menu Setup…………………………………………………………………………… …15…  
The high-performance W-V DSP chip  
effectively removes low-light gain noise and  
afterimage to provide clear images even in  
dark environments.  
Communication  
Coaxial communication methods are  
supported.  
- Protocol : Pelco Coaxitron  
LENS…………………………………………………………………………………… …16…  
EXPOSURE…………………………………………………………………………… …17…  
WHITE BALANCE…………………………………………………………………… …19…  
SSDR…………………………………………………………………………………… …20…  
BACKLIGHT…………………………………………………………………………… …20…  
SSNR3………………………………………………………………………………… …22…  
DAY/NIGHT…………………………………………………………………………… …23…  
SPECIAL……………………………………………………………………………… …24…  
EXIT…………………………………………………………………………………… …28  
Electrical Day&Night  
Miscellaneous Functions  
The camera automatically identifies when it is  
either day or night time and switched  
accordingly. During daylight the camera will  
switch to color to obtain excellent image  
clarity, while at night the camera will switch to  
monochrome to obtain improved picture  
definition.  
HLC(High Light Compensation), SENS-UP, FLIP  
(H/V-REV), D-ZOOM, SHARPNESS, MOTION  
DETECTION and PRIVACY functions are provided.  
OSD  
The camera’s OSD is complimented by 18  
languages.  
Troubleshooting ……………………………………………………………… 29  
Motion Detection  
- NTSC : Korean, English, French, Spanish,  
Japanese, Portuguese, Taiwanese  
- PAL : English, French, German, Spanish,  
Italian, Chinese, Russian, Czech,  
Polish, Romanian, Serbian, Swedish,  
Danish, Turkish, Portuguese  
Specifications…………………………………………………………………… 30  
Since the camera detects motion without any  
additional external sensor, you can monitor  
activity more efficient.  
COLOR CCD CAMERA  
User Guide  
COLOR CCD CAMERA  
User Guide  
4
5
Samsung Techwin cares for the environment at all product manufacturing  
stages to preserve the environment, and is taking a number of steps to provide  
customers with more environment-friendly products.The Eco mark represents  
Samsung Techwins will to create environment-friendly products, and indicates  
that the product satisfies the EU RoHS Directive.  
Precautions  
Do not install under extreme  
temperature conditions.  
Do not install in high humidity  
environment.  
Warnings & Cautions  
This information is provided to ensure your safety and to prevent any losses, financial or otherwise. Please read it  
carefully and use the product accordingly.  
Use only under temperature conditions between  
-10ºC and +50ºC. Provide good ventilation when  
using in high temperature conditions.  
May lower image quality.  
* For product inquiries, please contact the retail shop where you bought the camera. The use of equipment such as  
an aerial ladder while providing after-sales service shall be at your expense.  
* Separate the power plug during a thunder storm.  
* This product is only part of a surveillance system. Therefore, we can't compensate for material loss and personal  
injuries by robbery, fire, natural disaster or something like this type.  
Do not install under unstable  
lighting conditions.  
Avoid touching the camera lens.  
Warning/Attention/Special Mark Messages  
Ignoring this information may result in  
Ignoring this information may result in  
material loss and serious personal  
material loss and a slight injuries.  
injuries including death.  
Severe lighting changes or flickering may hinder  
normal camera operation.  
The lens is the most important component of  
the camera. Be careful not to smear it with  
fingerprints.  
Indicates “Never Allowed.”  
Indicates “No Disassembling.”  
Do not drop the camera or subject  
it to physical shock.  
Never keep the camera face to  
strong light directly.  
May cause a product malfunction.  
May damage the CCD.  
COLOR CCD CAMERA  
User Guide  
COLOR CCD CAMERA  
User Guide  
6
7
Precautions  
Overview  
Do not expose the camera to rain  
or other types of liquids.  
Do not expose the camera to  
radioactivity.  
Front View  
Side View  
5
4
3
2
1
May cause a product malfunction.Wipe dry any  
liquids. Liquids may contain minerals that are  
corrosive to electronic components.  
Radioactivity exposure may damage the CCD.  
1
2
3
CCD protection cap  
C-Mount lens adaptor : Please install this adapter when using a C-Mount Lens.  
CS-Mount lens adaptor : Please remove the C-MOUNT lens adaptor and then attach it.  
: Please cover the CCD SENSOR when not using it.  
Notes  
4
B
ack Focus clamp screw : Please loosen the clamp screw with a screwdriver before  
• Exposure to the spotlights or objects reflecting bright light, smearing or blooming may  
occur.  
• Ensure that the power source complies with normal specifications before connecting it to  
adjusting the Back Focal length.  
5
Auto Iris Lens Connector  
the camera.  
Bottom View  
6
6
Tripod Mounting Bracket Screw Hole  
Used to fix the camera on a bracket or tripod.  
The screw sizes for this hole are as follows:  
Components and Accessories  
1  
2
3
4
1/4"-20 UNC (20 THREAD)  
L:4.5mm±0.2mm (ISO standard),  
or 0.197" (ASA standard)  
1
2
3
4
Ultra High Resolution Camera SCB-2000  
Auto iris lens connection plug  
C-Mount adaptor  
You can separate the Tripod Mounting Bracket and install it on the top or  
bottom of the camera. Make sure to use the Tripod Mounting Bracket when  
fixing the camera to a bracket or tripod. Otherwise the camera may not be  
secure, or the internal circuitry of the camera may be damaged.  
Instruction manual  
COLOR CCD CAMERA  
User Guide  
COLOR CCD CAMERA  
User Guide  
8
9
Overview  
Installation  
When Using Auto Iris Lens  
Rear View  
1. Strip the insulation of the auto iris lens  
cable 8mm from the end.  
2. Strip the insulation of the core of the auto  
iris lens cable to expose a 2mm length.  
2mm  
7
8
8mm  
9
3. Remove the cover of the auto iris lens connector plug and solder the lens cable to the  
connector pin of the plug.  
*High Voltage Type  
7
8
Power lamp : Lights up when the correct power is supplied to the camera.  
Function Setup Button  
LENS  
VIDEO  
Lens cable  
Connector  
Pin No.  
DC  
•SETUP button : Displays the menu on the screen and uses enter sub menu.  
•Up&Down button : Used to move the cursor up or down in the menu screen.  
•Left&Right button : Used to move the cursor left or right in the menu screen.  
Video output terminal :  
Sends video signal and connects to the video input terminal of the monitor.  
Power input terminal : Connects to the power appropriate to each model.  
No.1 Pin Damping -  
No.2 Pin Damping +  
No.3 Pin Drive +  
No.4 Pin Drive -  
Red (power)  
NC  
No.3 Pin  
No.1 Pin  
White (video signal)  
Black (GND)  
No.4 Pin  
No.2 Pin  
9
4. Please replace the auto iris lens connection plug cover and take off the CCD protection  
cap, and then attach the auto iris lens to the camera by  
screwing it in clockwise.  
5. Please insert the connection plug that is connected to  
the auto iris lens cable into the auto lens connector,  
which is located on the side of the camera.  
Installation  
LENS  
The lens is not supplied with this camera. Purchase a lens suitable for your environment.  
This camera accepts the auto iris lens and both C-and CS-mount lens.  
When using a C-Mount lens  
Please take off the CCD protection cap and attach the C-Mount lens to  
Notes  
the camera by screwing it in clockwise.  
C-mount adaptor  
To use the functions of this camera effectively it is recommended that a DC type Auto Iris  
lens is used.  
• Keep the lens surface clean, if it becomes contaminated with dirt or fingerprints the  
picture quality suffers.  
COLOR CCD CAMERA  
User Guide  
COLOR CCD CAMERA  
User Guide  
11  
10  
Installation  
• The connection method varies depending on the type of monitor and accessories. Please  
refer to the user's manual for each instrument.  
When using a CS-Mount lens  
• Please turn off the power when connecting.  
1. Please take off the CCD protection cap  
and C-mount adaptor.  
2. Please attach the CS-Mount lens to the  
camera by screwing it in clockwise.  
Using Coaxial Communications  
Coaxial Communications System  
OSD Control method  
C-mount adaptor  
CS-mount adaptor  
CAMERA  
SET  
UP  
DVR  
MENU/ENTER  
UP KEY  
CONTROLLER  
OSD KEY  
JOYSTICK UP  
DOWN  
LEFT  
RIGHT  
DOWN KEY  
LEFT KEY  
RIGHT KEY  
JOYSTICK DOWN  
JOYSTICK LEFT  
JOYSTICK RIGHT  
CCD protection cap  
Notes  
DVR  
• Please use the specified lens connection parts as shown in the picture below.  
The use of the wrong sized parts may cause damage to the inside of the camera or  
result in poor fitting.  
DVD  
• Use of a lens which is too heavy affects the balance of the  
camera and may cause a malfunction. Please use a lens  
that weighs less than 450g.  
: BNC  
---- : RS-485  
• Please select Av mode if possible when adjusting the  
automatic light control (ALC) of an auto lens. Use of PK  
mode may cause hunting.  
C-mount lens : 10 mm or less  
CS-mount lens : 5 mm or less  
Video Cable  
The camera's video output port is connected to the monitor with a BNC coaxial cable,  
shown below : If the distance between the camera and the monitor exceeds the  
recommended maximum, please use an auxiliary video amp.  
Connecting to the Monitor  
Please connect the video output terminal located on the back of the camera to the monitor.  
Distance  
300m  
Recommended Cable Specification  
3C2V(RG-59/U)  
450m  
5C2V(RG-6/U)  
600m  
7C2V(RG-11/U)  
Notes  
• It is recommended that pure copper coax cable is used and not copper coated steel, as  
this will cause issues with the communication over the coaxial cable.  
CCD Camera  
Monitor  
COLOR CCD CAMERA  
User Guide  
COLOR CCD CAMERA  
User Guide  
13  
12  
Installation  
Operating Your Camera  
Connecting to the Power  
Menu Configuration  
Each model has a different power input specification. Please check the model type and  
standard power requirement before connecting to power.  
MAIN MENU  
DC  
MANUAL  
LENS  
VIDEO  
…………………  
………  
AGC  
BRIGHTNESS  
SHUTTER  
EXPOSURE  
AC/DC Power Type  
DC Power Type  
SENS-UP  
RETURN  
ATW  
OUTDOOR  
INDOOR  
• Use AC24V, 300mA adaptor or DC12V,  
500mA for SCB-2000N/P  
• Use DC12V, 500mA for SCB-2000ND/PD  
WHITE BALANCE  
MANUAL  
AWCSET  
ON  
SSDR  
OFF  
HLC  
BACKLIGHT  
SSNR3  
OFF  
BLC  
OFF  
ON  
AUTO  
DAY/NIGHT  
COLOR  
B/W  
IMAGE ADJ.  
MONITOR  
CAM TITLE  
SYNC  
PRIVACY  
……  
SPECIAL  
MOTION DET  
RETURN  
DIS  
LANGUAGE  
RESET  
EXIT  
SAVE  
NOT SAVE  
High Voltage Type (AC230V, 50Hz)  
Menu Setup  
• Use AC230V, 50Hz power source for SCB-  
2000PH.  
You can set up functions using the 5 buttons on the rear of the camera.  
When the resistance value of copper wire is at [20ºC(68°F)]  
Copper wire size (AWG)  
Resistance (Ω / m)  
#24(0.22)  
0.078  
#22(0.33)  
0.050  
#20(0.52)  
0.030  
#18(0.83)  
0.018  
UP button  
SET button  
Voltage Drop (V/m)  
0.028  
0.018  
0.011  
0.006  
LEFT button  
DOWN button  
RIGHT button  
• As shown in the table above, voltage decreases as the wire gets longer.  
Therefore use of an excessively long adaptor output line for connection to the camera  
may affect the performance of the camera.  
1. Press the SET button.  
• Main setup menu is displayed on the monitor screen.  
*
*  
Standard voltage for camera operation : DC 12V±10%, AC 24V±10%, AC 230V ±10% (SCB-2000PH)  
There may be some deviation in voltage drop depending on the type of wire and the manufacturer.  
COLOR CCD CAMERA  
User Guide  
COLOR CCD CAMERA  
User Guide  
15  
14  
- Level (VIDEO)  
:Adjusts the level of video iris signals; the higher the level is,  
Operating Your Camera  
the brighter the video looks.  
- FOCUS ADJ. (DC,VIDEO) :To adjust the DC and VIDEO lens focus correctly, you must  
activate the Focus Settings mode under each lens menu.  
Activate the Focus Settings mode, adjust the lens focus, and  
then deactivate the settings mode. (The VIDEO lens requires  
an extra step: go to the sub menu of the Focus Settings  
mode and change the shutter speed to adjust the lens  
brightness.)  
MAIN MENU  
Select the function using  
the UP or DOWN button.  
Change the status using  
the LEFT or RIGHT button.  
1.LENS  
DC  
2.EXPOSURE  
3.WHITE BAL  
4.SSDR  
ATW  
OFF  
OFF  
ON  
- IRIS SPEED (DC)  
:
Adjusts the Iris control speed of the DC lens. If the control speed  
is too slow or fast, please use this menu to adjust the speed.  
5.BACKLIGHT  
6.SSNR3  
Notes  
7.DAY/NIGHT  
8.SPECIAL  
9.EXIT  
COLOR  
When using VIDEO lens, adjust the lens VR explained below first and set the focus using  
'FOCUS ADJ.' menu.  
SAVE  
If color rolling occurs when using a DC lens, set Shutter to A.FLK.  
Some lenses may not work properly, depending on the setting of the BRIGHTNESS LEVEL.  
• When Using a Video-Type Auto Iris Lens  
2. Select a desired function using the Up and Down buttons.  
• Place the cursor over a desired item.  
3. Set up a selected item by using the Left and Right buttons.  
4.To finish the setting, select ‘EXIT’ and press the SET button.  
Adjust the ALC adjustment terminal on the lens appropriately. In general, set it to AV  
(Average).  
2It may not work properly depending on the installed lens. Set the Level VR of the lens  
to the optimal value.  
3Set AGC to OFF and adjust the Lens VR to an appropriate brightness.  
4Adjust the Lens VR, adjust the BRIGHTNESS, and then check if the screen brightness  
changes properly. Otherwise, adjust the Lens VR again.  
Notes  
• An item with the  
icon also has sub menus. To select a sub menu, select an item with  
the icon and press the SET button.  
• An item with the - - - icon is unavailable due to function settings.  
EXPOSURE  
LENS  
MAIN MENU  
Using this function, you can control the screen brightness.  
1.When the SETUP menu screen is displayed, selectLENSby using the Up and Down  
buttons so that the arrow indicatesLENS.  
1.LENS  
DC  
2.EXPOSURE  
3.WHITE BAL  
ATW  
2. Select the connected lens type by using the Left and Right buttons.  
1.When the SETUP menu screen is displayed, selectEXPOSUREby using the Up and  
MAIN MENU  
Down buttons so that the arrow indicatesEXPOSURE.  
1.LENS  
DC  
2. Select a desired mode using the Up and Down buttons.  
2.EXPOSURE  
EXPOSURE SETUP  
DC/Video : Select Auto Iris Lens  
1.BRIGHTNESS  
2.SHUTTER  
3.AGC  
4.SENS-UP  
5.RETURN  
25  
You can adjust the minimum shutter and maximum value of ESC shutter  
mode when DC Lens mode is selected.  
Manual : Select Manual Lens  
ESC  
HIGH  
OFF  
3. Each Lens mode has sub menu items as listed below.  
- Brightness (DC, Manual) :Adjusts the video brightness.  
COLOR CCD CAMERA  
User Guide  
COLOR CCD CAMERA  
User Guide  
17  
16  
Operating Your Camera  
SHUTTER :You can select either auto or manual shutter.  
White Balance (White Bal.)  
- ---  
: Shutter speed is fixed at 1/60sec(1/50sec).  
- A.FLK  
: Select this when you experience picture flicker, which can happen when  
there is a clash with the frequency of the installed lighting.  
: Select this to control the shutter speed automatically. If ESC is selected, the  
shutter speed is automatically controlled depending on the ambient  
illumination of the subject.  
Use the White Balance function to adjust the screen color.  
1.When the SETUP menu screen is displayed, select ‘White Bal.’ by using the Up and  
Down buttons so that the arrow indicates ‘White Bal.’ .  
- ESC  
2. Select a desired mode using the Up and Down buttons.  
- MANUAL :You can control shutter speed manually. (1/60 ~ 1/120,000)  
MAIN MENU  
Notes  
1.LENS  
DC  
2.EXPOSURE  
3.WHITE BAL  
4.SSDR  
• When you use a DC lens, set the shutter mode to A.FLK if color rolling occurs.  
• When the SHUTTER is set to ESC after selecting the Internal Synchronization Type, the  
picture may become unstable if the camera faces a bright fluorescent light. Therefore,  
take care when choosing the installation position.  
ATW  
OFF  
• When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled.  
Select one of the following 5 modes, as appropriate for your purpose.  
ATW  
: Select this when the color temperature is between 1,700˚K and  
11,000˚K.  
AGC(AUTO GAIN CONTROL) : The higher the gain level, the brighter the screen - but  
the higher the noise.  
- OFF : Deactivates the AGC function.  
OUTDOOR : Select this when the color temperature is between 1,700˚K and  
11,000˚K. (sodium light inclusion)  
- LOW :Allows automatic gain control from 5.3dB to 32dB.  
- HIGH :Allows automatic gain control from 5.3dB to 37dB.  
INDOOR  
MANUAL  
:
:
Select this when the color temperature is between 4,500˚K and 8,500˚K.  
Select this to fine-tune White Balance manually. Set White Balance first by  
using the ATW or AWC mode.After that switch to MANUAL mode, fine-  
tune the White Balance and then press the SET button.  
SENS-UP : When it is night or dark, the camera automatically detects the light level and  
maintains a clear picture if this mode is activated.  
AWCSET : To find the optimal luminance level for the current environment, point the  
camera towards a sheet of white paper and press the Function Setup switch. If  
the environment changes, readjust it.  
- OFF : Deactivates the SENS-UP function.  
- AUTO :Activates the SENS-UP function.  
RETURN : Select this to save the changes in the EXPOSURE menu and return to the SETUP menu.  
Notes  
Notes  
• White Balance may not work properly under the following conditions. In this case select  
the AWC mode.  
When the color temperature of the environment surrounding the subject is out of the  
control range (e.g. clear sky or sunset).  
• If you press the SET button in ‘AUTO’ mode, You can adjust brightness by increasing or  
decreasing the shutter speed. (x2 ~ x512)  
• Note that the higher the zoom level, the brighter the screen, but the more likely it is that an  
after-image will appear.  
2
When the ambient illumination of the subject is dim.  
• Although Noise, Spots, and Whitish symptoms may occur in SENS-UP operation when the  
zoom level is increased, this is normal.  
3
If the camera is directed towards a fluorescent light or is installed in a place where  
illumination changes dramatically, the White Balance operation may become unstable.  
COLOR CCD CAMERA  
User Guide  
COLOR CCD CAMERA  
User Guide  
19  
18  
Operating Your Camera  
SSDR (Samsung Super Dynamic Range)  
MAIN MENU  
1.LENS  
DC  
SSDR illuminates darker areas of an image while retaining the same light level for brighter  
areas to even out the overall brightness of images with high contrast between bright and  
dark areas.  
2.EXPOSURE  
3.WHITE BAL  
4.SSDR  
ATW  
OFF  
OFF  
5.BACKLIGHT  
MAIN MENU  
1.LENS  
DC  
2. Select a desired mode using the Left and Right buttons depending on the camera purpose.  
2.EXPOSURE  
3.WHITE BAL  
4.SSDR  
ATW  
OFF  
OFF  
BLC : Enables a user to select a desired area on a picture and view that area more  
clearly.  
5.BACKLIGHT  
HLC (High Light Compensation) :  
If the scene contains extremely bright light areas such as; from car headlight, the light  
can mask out much of the on-screen detail.  
- LEVEL :Adjust level of the HLC function.  
- LIMIT : Enable to change the operating condition.  
- MASK COLOR/TONE : Change the color / brightness of the masking area.  
(Black, Red, Blue, Cyan, Magenta)  
1.When the SETUP menu screen is displayed, select ‘SSDR’ by using the Up and Down  
buttons so that the arrow indicates ‘SSDR’.  
2. Use the Left/Right buttons to change the SSDR level in the sub menu according to the  
contrast between bright and dark areas.  
- TOP/BOTTOM/LEFT/RIGHT :Adjust the area to be enhanced.  
OFF : Not being used  
3. Select a desired mode using the Left and Right buttons and press the SET button.  
Select ‘BLC’ to adjust the area to be  
enhanced then adjust the level.  
HLC : Enable the user to change the level,  
limit, mask color/tone and area.  
SSDR ON  
SSDR OFF  
BACKLIGHT  
Unlike conventional cameras, the SCB-2000 is designed so that it delivers a distinctive  
subject and background at the same time, even when the subject is in backlight, by  
adopting a proprietary W-V DSP chip.  
1.When the SETUP menu screen is displayed, select ‘BACKLIGHT’ by using the Up and  
Down buttons so that the arrow indicates ‘BACKLIGHT’.  
COLOR CCD CAMERA  
User Guide  
COLOR CCD CAMERA  
User Guide  
21  
20  
Operating Your Camera  
Notes  
DAY/NIGHT  
• Because there can be a difference in the effectiveness of HLC according to the amount of  
light area in the screen, optimize the installation angle for the best HLC performance.  
You can display pictures in color or black and white.  
1.When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the Up and  
Down buttons so that the arrow indicates ‘DAY/NIGHT’.  
When dark, the HLC is only activated when a bright light exceeding a specific size.in NIGHT ONLY mode.  
The HLC is not activated in day light or when bright light is not present at night.in NIGHT ONLY mode.  
MAIN MENU  
1.LENS  
DC  
2.EXPOSURE  
3.WHITE BAL  
4.SSDR  
ATW  
OFF  
OFF  
ON  
SSNR3  
This function reduces the background noise in a low luminance environment.  
1.When the SETUP menu screen is displayed, select ‘SSNR’ by using the Up and Down  
buttons so that the arrow indicates ‘SSNR’ .  
5.BACKLIGHT  
6.SSNR3  
7.DAY/NIGHT  
8.SPECIAL  
COLOR  
MAIN MENU  
1.LENS  
DC  
2. Select a desired mode using the Left and Right buttons according to the picture display you want.  
COLOR :The picture is always displayed in color.  
2.EXPOSURE  
3.WHITE BAL  
4.SSDR  
ATW  
OFF  
OFF  
ON  
B/W  
:The picture is always displayed in black and white.  
You can turn on or off the burst signal on B/W mode.  
5.BACKLIGHT  
6.SSNR3  
AUTO :The mode is switched to ’Color‘ in a normal  
environment, but switches to ’B/W‘ mode  
when ambient illumination is low.To set up  
the switching time for AUTO mode, press the  
SET button.  
7.DAY/NIGHT  
COLOR  
2. Select a desired mode using the Left and Right buttons.  
OFF: Deactivates SSNR. Noise is not reduced.  
ON :Activates SSNR so that noise is reduced.  
You can turn on or off the burst signal on  
B/W mode.  
- DWELL TIME :You can select the duration time about  
changing the day/night mode. …  
3. Set the SSNR mode to ‘ON’ and press the SET button.Then you can adjust the noise reduction level.  
5s, 7s, 10s, 15s, 20s, 30s, 40, 60s  
Notes  
Notes  
• When using a Video Auto Iris Lens, if you set the lens level to low, automatic switching  
between Color and Black & White may not occur.  
You cannot set the SSNR to ‘ON’ or ‘OFF’ when the AGC mode of the EXPOSURE menu is ‘OFF’.  
• When AGC in the EXPOSURE menu is 'OFF', '---' mode operates as like selecting 'COLOR'  
mode and 'AUTO' mode can not be selected.  
• When adjusting the noise reduction level in the SSNR mode, remember that the higher  
the level set, the more the noise level will be reduced, as will the brightness of the image.  
COLOR CCD CAMERA  
User Guide  
COLOR CCD CAMERA  
User Guide  
23  
22  
Operating Your Camera  
2) Select a desired mode using the Up and Down buttons.  
SPECIAL  
1.When the SETUP menu screen is displayed, select ‘SPECIALby using the Up and Down  
buttons so that the arrow indicates ‘SPECIAL.  
IMAGE SETUP  
1. V-REV  
OFF  
2. H-REV  
3. D-ZOOM  
4. FONT COLOR  
5. SHARPNESS  
6. RETURN  
OFF  
OFF  
WHITE  
ON  
MAIN MENU  
1.LENS  
DC  
2.EXPOSURE  
3.WHITE BAL  
4.SSDR  
ATW  
OFF  
OFF  
ON  
V-REV  
H-REV  
D-ZOOM  
:You can flip the picture vertically on the screen.  
:You can flip the picture horizontally on the screen.  
:You can use a digital zoom of x1 ~ x16.  
5.BACKLIGHT  
6.SSNR3  
7.DAY/NIGHT  
8.SPECIAL  
9.EXIT  
COLOR  
FONT COLOR : You can change the OSD font color. (White,Yellow, Green, Red, Blue)  
SHARPNESS :As you increase this value, the picture outline becomes stronger and  
clearer.Adjust this value appropriately depending on the sharpness of  
the picture.  
SAVE  
2. Select a desired mode using the Up and Down buttons.  
RETURN  
: Select this to save the settings for the IMAGE ADJ. menu and to  
return to the SETUP menu.  
SPECIAL  
1. IMAGE ADJ  
Notes  
2. MONITOR  
3. CAM TITLE  
4. SYNS  
5. MOTION DET  
6. PRIVACY  
7. DIS  
LCD  
OFF  
INT  
OFF  
OFF  
OFF  
• When the V-REV or H-REV mode is enabled, the text on the screen does not flip.  
• If you increase the SHARPNESS level too high, the picture may become distorted or noise  
may appear.  
8. LANGUAGE  
9. RETURN  
ENGLISH  
Monitor : Please change the settings value of video  
appropriate to your monitor.  
- LCD : Please select this menu item when using an LCD  
monitor.  
- CRT  
:
Please select this menu item when using a CRT  
monitor.  
IMAGE ADJ. :  
- USER : Please use this menu item when using a monitor  
other than standard ones.You can change the  
1) When the SETUP menu screen is displayed, select ‘IMAGE ADJ.’ by using the Up  
and Down buttons so that the arrow indicates ’IMAGE ADJ‘.  
gamma, PED level, and color gain in the sub menus.  
COLOR CCD CAMERA  
User Guide  
COLOR CCD CAMERA  
User Guide  
25  
24  
Operating Your Camera  
Notes  
When using AC power at 60Hz frequency, you can use the L/L type synchronization.  
CAM TITLE : If you enter a title, the title will appear on the monitor.  
• When the power is DC 12V, the SYNC menu is fixed to the ‘INT’ mode.  
1) If the SPECIAL menu screen is displayed, use the Up and Down buttons so that the  
arrow indicates ‘CAM TITLE’.  
:
MOTION DET  
CAMERA TITLE SETUP  
2) Set it to ‘ON’ by using the Left and Right buttons.  
This product has a feature that allows you to observe  
movement of objects in 8 different areas on the screen,  
and the words 'MOTION DETECTED' appear on the  
screen when movement is detected.  
ABCDEFGHIJKLM  
NOPQRSTUVWXYZ  
abcdefghijklm  
nopqrstuvwxyz  
3) Press the SET button.  
4) Use the 4 direction buttons to move to a  
desired letter and select the letter by  
- . 0 1 2 3 4 5 6 7 8 9  
pressing the SET button. Repeat this to  
enter multiple letters. You can enter up to  
15 letters.  
5) Enter a title, move the cursor to ‘POS’ and press  
the SET button. The entered title appears on the  
you can monitor activity more efficient.  
← → CLR POS END  
1) When the SPECIAL menu screen is displayed, press the Up and Down buttons so  
that the arrow indicatesMOTION DET.  
FRONT DOOR  
2) Set up the mode using the 4 direction buttons.  
screen. Select the position to display the title on  
the screen by using the 4 direction buttons and  
press the SET button. When the position is  
determined, select ‘END’ and press the SET button  
to return to the SPECIAL menu.  
- SENSITIVITY :You can select up to 8 MD areas.When SENSITIVITY number is high,  
motion detection sensitivity is increased to recognize even small  
movement.  
- AREA MODE : Determines whether to use the MD area selected in SENSITIVITY.  
- SEL POS  
- YPOS  
- XPOS  
: Determines which of the 4 vertices of each MD area is to be used.  
: Determines the coordinate of the vertical axis for SEL POS.  
: Determines the coordinate of the horizontal axis for SEL POS.  
Notes  
• When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even  
if you enter one.  
• Only English is available in this mode.  
• If you move the cursor to CLR and press the SET button, all the letters are deleted. To edit  
a letter, change the cursor to the bottom left arrow and press the SET button. Move the  
cursor over the letter to be edited, move the cursor to the letter to be inserted and then  
press the SET button.  
- FILLSET : Fills in a selected MD area. The color of filling is sequentially selected  
as brown, orange, blue, cyan, green, yellow, magenta and red.  
- RETURN  
: Select this to save the MOTION DET menu settings and return to the  
SPECIAL menu.  
PRIVACY : Mask an area you want to hide on the screen.  
PRIVACY AREA SETUP  
SYNC : In areas where the supply is at 60Hz, you can  
synchronize the output phase of multiple cameras  
using the power synchronization function (Line-  
Lock) without using a synchronization signal  
generator.  
- INT : Internal Synchronization Type  
- L/L : Power Synchronization Type, Line-lock  
• Press the Function Setup switch.  
1. AREA  
2. MODE  
AREA1  
OFF  
GREEN  
1
39  
79  
3. MASK COLOR  
4. MASK TONE  
5. TOP  
6. BOTTOM  
7. LEFT  
12  
51  
8. RIGHT  
9. RETURN  
You can select a desired phase from 0 to 359 when select 'phase'.  
COLOR CCD CAMERA  
User Guide  
COLOR CCD CAMERA  
User Guide  
27  
26  
Troubleshooting  
Operating Your Camera  
1) When the SPECIAL menu screen is displayed, press the Up and Down buttons so  
that the arrow indicates ‘PRIVACY’.  
If you have trouble operating your camera, refer to the following table.  
If the guidelines do not enable you to solve the problem, contact an authorized technician.  
2) Set up the mode using the 4 direction buttons.  
Nothing appears on the screen.  
- AREA SEL  
- MODE  
:
You can select up to 12 PRIVACY areas.  
Check that the power cord and line connectionbetween the camera and monitor are  
: Determines whether to use the area selected in the AREA SEL.  
fixed properly.  
- MASK COLOR : Determine area color.You can select Green, Red, Blue, Black,White, Gray.  
- MASK TONE :Adjust the brightness of MASK COLOR.  
- TOP/BOTTOM/LEFT/RIGHT :Adjust the size and position of the selected area.  
Check the type of lens.  
Check that the lens type is VIDEO lens or DC lens.  
The image on the screen is dim.  
- RETURN  
: Select this to save the PRIVACY menu settings and return to the SPECIAL  
menu.  
Is lens stained with dirt? Clean your lens with soft, clean cloth.  
Set the monitor to proper condition.  
If the camera is exposed to too strong light, change the camera position.  
DIS (Digital Image Stabilizer) :  
This function mitigates any picture movement due to external factors such as wind.  
The image on the screen is dark.  
Adjust the contrast feature of the monitor.  
If you have an intermediate device, set the 75Ω / Hi-z properly.  
Notes  
The camera is not working properly, and the surface of the camera is hot.  
Check that you have properly connected the camera to an appropriate power source.  
As the DIS function uses the digital zoom the camera's resolution will decrease.  
DIS doesn’t operate when background illumination is too low.  
DIS doesn’t operate when object pattern is monotonic as like sky or white wall.  
The SENS-UP function does not work.  
Check that AGC of EXPOSURE SETUP menu is ‘OFF’.  
Check that SHUTTER of EXPOSURE SETUP menu is A.FLK’ or ‘MANUAL’.  
LANGUAGE :You can select the menu language according to your requirements.  
The Motion Detection function does not work.  
Check that MOTION DET of SPECIAL SETUP menu is ‘OFF’.  
RETURN : Select this to save the SPECIAL menu settings and return to the MAIN  
SETUP menu.  
Color is not correct.  
Check the setting of WHITE BAL SETUP menu .  
The screen flickers continually.  
Check that direction of camera turns toward the Sun.  
EXIT  
When coaxial communication is not available:  
Select a desired EXIT mode using the Left and Right buttons depending on the camera  
purpose.  
Make sure that the camera and monitor are installed within the recommended distance.  
Use the video amplifier equivalent to coaxitron if the recommended installation  
- SAVE  
: Save the current settings and exit the MAIN SETUP menu.  
distance is exceeded.  
- NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu.  
- RESET  
: Resets the camera settings to the factory defaults. Language and Monitor  
settings are not initialized.  
COLOR CCD CAMERA  
User Guide  
COLOR CCD CAMERA  
User Guide  
29  
28  
Specifications  
DECLARATION OF CONFORMITY  
Application of Council Directive(s)  
2004 / 108 / EC  
SCB-2000ND  
SCB-2000N  
SCB-2000PD  
SCB-2000P  
SCB-2000PH  
ELECTRICAL  
Input Voltage  
Power Consumption  
VIDEO  
Imaging Device  
Total Pixels  
Effective Pixels  
Scanning System  
Synchronization  
Frequency  
Horizontal Resolution  
Min. Illumination  
S/N (Y Signal)  
Video Output  
OPERATIONAL  
IRIS Adustment  
Electronic Shutter Speed  
On Screen Display  
SSDR  
Manufacturer's Name  
Manufacturer's Address  
SAMSUNG TECHWIN CO., LTD  
SAMSUNG TECHWIN CO., LTD  
42, SUNGJU-DONG CHANGWON-CITY,  
KYUNGNAM, KOREA, 641-716  
DC 12V  
Max 2.5W  
AC 24V / DC 12V  
Max 3.5W  
DC 12V  
Max 2.5W  
AC 24V / DC 12V  
Max 3.5W  
AC 230V, 50Hz  
Max 4.0W  
1/3 inch, Diagonal 6mm Super HAD CCD  
811(H) x 508(V)  
768(H) x 494(V)  
2:1 Interlace  
Internal Only  
H : 15.734KHz V:59.54Hz  
600TVL  
0.05 Lux(50IRE, No SENS-UP) / 0.0001Lux (SENS-UP x512) @F1.2  
52dB (Weight Off, AGC Off)  
CVBS : 1.0Vp-p, 75Ω composite  
795(H) x 596(V)  
752(H) x 582(V)  
European Representative Name  
European Representative Address  
Equipment Type/Environment  
Model Name  
Internal /LineLock  
Internal Only Internal / Line-Lock  
H: 15.625KHz V: 50.00Hz  
CCTV Camera  
SCB-2000P, SCB-2000PH, SCB-2000PD  
C59W6V3Z200001X  
2010.02.01  
DC / VIDEO  
1/60 ~ 1/120K sec  
NTSC : 7 Languages, PAL : 15 Languages  
On / Off (Level adjustable)  
Beginning Serial NO.  
1/50 ~ 1/120K sec  
Year of Manufacture  
Backlight Compensation  
Day & Night  
Gain Control  
White Balance  
SENS-UP (frame Integration)  
Motion Detection  
Privacy Masking  
3D Noise Filter (SSNRIII)  
Digital Zoom  
BLC / HLC / OFF  
COLOR / BW / AUTO (Electric)  
Low / High / Off  
ATW / OUTDOOR / INDOOR / MANUAL / AWC (1,700°K ~ 11,000°K)  
Auto /Off (Selectable x2 ~ x512)  
On / Off (8 Programmable zones)  
On / Off (12 Programmable zones)  
On / Off (Level adjustable)  
Conformance to  
EN 55022 : 2006  
EN 50130-4 : 2003  
On / Off (x1 ~ x16)  
Digital Image  
Stabilization(DIS)  
On / Off  
We, the undersigned, hereby declare that the equipment specified above conforms  
to the above Directive(s).  
Camera Title  
Sharpness  
Flip / Mirror  
Off / On (Displayed 15 Characters)  
On / Off (Level adjustable)  
On / Off  
Communication  
ENVIRONMENTAL  
Operating Temp/Humid  
Storage Temp/Humid  
MECHANICAL  
Lens Mount  
Back Focus Adjustment  
Dimension  
Weight  
Coaxial (Protocol : Pelco Coaxitron)  
Manufacturer SAMSUNG TECHWIN CO., LTD  
Signature  
Legal Representative in Europe  
-10°C ~ +50°C / 30% ~ 80% RH  
-20°C ~ +60°C / 20% ~ 90% RH  
Signature  
Full Name  
Position  
Place  
Full Name  
Position  
Place  
BONJENG GU  
C / CS Mount  
Manual  
58(W) x 52(H) x 121(D)mm  
QUALITY CONTROL MANAGER  
CHANGWON, KOREA  
2010.02.01  
290g  
310g  
290g  
310g  
510g  
The specification for this product may change without prior notice for product improvement.  
Date  
Date  
COLOR CCD CAMERA  
User Guide  
COLOR CCD CAMERA  
User Guide  
31  
30  

Yamaha 3D Blu ray Player Manual BD S673 User Manual
Westcott 1824 User Manual
ViewSonic VS11964 User Manual
Standard Horizon Car Amplifier BMF600D User Manual
Sony LCH FXA User Manual
Sony ILCE5100B User Manual
Sony Ericsson Car Stereo System HCB 30 User Manual
Sony DT 55 200MM F4 5.6 SAM User Manual
Sony Camcorder CX230 User Manual
Samsung Camcorder HMX F80SP User Manual