USER
HMX-F90/HMX-F91
HMX-F900/HMX-F910
HMX-F920
Digital Camcorder
www.samsung.com/register
For video recording, use a memory card that supports faster write speeds.
Recommended Memory Card: 6MB/s (Class 6) or above.
-
Important safety instructions
14 Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
(grounding) pin. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug still fails to fit, contact
your electrician to replace your outlet. Do not defeat the safety
purpose of the polarized plug.
19 POWER-CORD PROTECTION:
Power-supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against
them, paying particular attention to cords or plugs, convenient
receptacles, and the point where they exit from the unit.
15 Apparatus shall not be exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall be placed on the
apparatus.
16 VENTILATION:
20 OUTDOOR ANTENNA GROUNDING:
Slots and openings in the cabinet are provided for ventilation to
ensure reliable operation of the CAMCORDER and to protect
it from overheating. These openings must not be blocked or
covered. Never place your CAMCORDER on a bed, sofa, rug, or
other similar surface: on or near a radiator or heat register. This
CAMCORDER should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is provided or
the manufacturer’s instructions have been adhered to.
CAMCORDER, be sure the antenna or cable system is grounded
to provide some protection against voltage surges and built-
up static charges, Section 810 of the National Electrical Code,
ANSI/NFPA No. 70-1984, provides information with respect
to proper grounding of the mast and supporting structure,
grounding of the lead-in wire and supporting structure,
grounding of the mast and supporting structure, grounding of
the lead-in wire to an antenna discharge unit, size of grounding
to conductors, location of antenna-discharge unit, connection
to grounding electrodes and requirements for the grounding
electrode. See figure below.
17 POWER SOURCES:
The CAMCORDER should be operated only from the type of
power source indicated on the label. If you are not sure of the
type of power supply at your home, consult your appliance
dealer or local power company. A CAMCORDER is intended to
be operated from battery power, or other sources, refer to the
operating instructions.
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
18 GROUNDING OR POLARIZATION:
ELECTRIC
SERVICE
GROUNDING CONDUCTORS
EQUIPMENT
(NEC SECTION 810-21)
GROUND CLAMPS
This CAMCORDER may be equipped with either a polarized
2-wire AC line plug (a plug having one blade wider than the
other) or a 3-wire grounding type plug, a plug having a third
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC NATIONAL ELECTRICAL CODE
iii
Important safety instructions
a. When the power-supply cord or plug is damaged.
21 LIGHTNING:
For added protection of this CAMCORDER during a lightning
storm or when it is left unattended and unused for long periods
of time, unplug it from the wall outlet and disconnect the antenna
or cable system. This will prevent damage to the CAMCORDER
due to lightning and powerline surges.
b. If any liquid has been spilled onto, or objects have fallen into the
CAMCORDER.
c. If the CAMCORDER has been exposed to rain or water.
d. If the CAMCORDER does not operate normally by following the
operating instructions, adjust only those controls that are covered
by the operating instructions. Improper adjustment of other
controls may result in damage and will often require extensive
work by a qualified technician to restore the CAMCORDER to its
normal operation.
22 POWER LINES:
An outside antenna system should not be located in the vicinity
of overhead power lines or other electric light or power circuits
where it can fall into such power lines or circuits. When installing
an outside antenna system, extreme care should be taken to
keep from touching such power lines or circuits as contact with
them might be fatal.
e. If the CAMCORDER has been dropped or the cabinet has been
damaged.
f. When the CAMCORDER exhibits a distinct change in
performance, this indicates a need for service.
23 OVERLOADING:
Do not overload wall outlets and extension cords as this can
result in a risk of fire or electric shock.
27 REPLACEMENT PARTS:
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer and having the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric shock
or other hazards.
24 OBJECTS AND LIQUIDS:
Never push objects of any kind into this CAMCORDER through
openings as they may touch dangerous voltage points or short
out a part that could result in a fire or electric shock. Never
spill liquids of any kind onto the CAMCORDER. Should spillage
occur, unplug unit and have it checked by a technician before
use.
28 SAFETY CHECK:
Upon completion of any service or repairs to this CAMCORDER,
ask the service technician to perform safety checks to determine
that the CAMCORDER is in safe operating order.
25 SERVICING:
Do not attempt to service this CAMCORDER yourself. Opening
or removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service personnel.
29 To prevent damage which may result in fire or shock hazard, do
not expose this appliance to rain or moisture.
26 DAMAGE REQUIRING SERVICE:
30 If this power supply is used at 240V ac, a suitable plug adaptor
Unplug this CAMCORDER from the wall outlet and refer servicing
to qualified service personnel under the following conditions:
iv
should be used.
Important safety instructions
USER INSTALLER CAUTION:
NOTE:
Your authority to operate this FCC certified equipment could be voided if
you make changes or modifications not expressly approved by this party
responsible for compliance to part 15 FCC rules.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules.
NOTE:
These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
Hg
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE
RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR
FEDERAL LAWS. For details see lamprecycle.org, eiae.org, or call 1-800-
Samsung (7267864)
CALIFORNIA USA ONLY
This Perchlorate warning applies only to primary CR (Manganese
Dioxide) Lithium coin cells in the product sold or distributed ONLY in
California USA “Perchlorate Material - special handling may apply, See
www.dtsc.ca.gov/hazardouswaste/perchlorate”.
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help and for
additional suggestions. The user may find the following booklet prepared
by the Federal Communications Commission helpful: “How to Identify and
Resolve Radio-TV Interference Problems.” This Booklet is available from
the U.S. Government Printing Office, Washington, D.C. 20402, Stock No.
004-000-00345-4.
FCC Warning
The user is cautioned that changes or modifications not
expressly approved by the manufacturer could void the user’s
authority to operate the equipment.
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions;
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
v
Before reading this user manual
SAFETY WARNINGS
IMPORTANT INFORMATION ON USE
What the icons and signs in this user manual mean:
About this user manual
Safety Icon
Meaning
Thank you for purchasing this Samsung Camcorder. Please read
this user manual carefully before you use the camcorder and keep
it handy for future reference. Should your camcorder fail to operate
correctly, refer to Troubleshooting. pages 93~102
There is a potential risk of death or serious injury.
WARNING
CAUTION
There is a potential risk of personal injury or damage to the
product.
This User Manual covers models HMX-F90, HMX-F91,
HMX-F900, HMX-F910, and HMX-F920.
To reduce the risk of fire, explosion, electric shock, or personal
injury when using your camcorder, follow these basic safety
precautions.
•
•
Illustrations of model HMX-F90 are used in this user manual.
The displays in this user manual may not be exactly the same as
those you see on the LCD screen.
Here are hints or page number references you will find helpful
when you operate the camcorder.
•
•
•
•
•
Designs and specifications of the camcorder and other
accessories are subject to change without notice.
Settings required before using a function.
These warning signs are here to prevent injury to you and others.
Please follow them explicitly. After reading this section, keep it in a
safe place for future reference.
Before using the camcorder, read the Safety information carefully
and then use the product properly.
Samsung is not responsible for any injury or damage caused by
not following the instructions in the user manual.
PRECAUTIONS
In this manual, a ‘memory card’ or ‘card’ means an SD, SDHC,
or SDXC memory card.
Warning!
•
In this user manual’s function description tables, the icon shown
in the on-screen display column will appear on the screen when
you set the corresponding function.
Example: 720X480/60p (16:9) - Video Resolution Submenu
item page 53
When using the AC power adaptor with your camcorder, connect the
adaptor to an outlet with protective grounding.
Do not expose the camcorder battery to direct sunlight, heaters,
radiators, fire, or any source of excessive heat.
•
On-screen
display
Item
Use
Caution
If you replace the battery with the wrong battery, you can cause an
explosion. Replace only with the same battery or an equivalent type.
720X480/60p
(16:9)
Records in 720x480 (60p) resolution
with 16:9 aspect ratio.
If you set the video resolution to 720X480/60p (16:9), the
corresponding icon ( ) will appear on the screen.
If you plug the AC power adaptor into a 240V AC outlet, be sure to use a
suitable plug adaptor.
2
Before reading this user manual
The following terms are used in this manual:
Notes regarding trademarks
•
‘Scene’ refers to the point where you press the [Recording
start/stop] button to start recording until you press it again to
stop recording.
•
All the trade names and registered trademarks mentioned in this
manual or other documentation provided with your Samsung
product are trademarks or registered trademarks of their
respective holders. Furthermore, ‘TM’ and ‘®’ are not mentioned in
each case in this manual.
•
The terms ‘photo’ and ‘still image’ are used interchangeably with
the same meaning.
•
•
SD, SDHC and SDXC logos are trademarks of SD-3C, LLC.
Microsoft®, Windows®, Windows Vista®, Windows® 7, and
DirectX® are either registered trademarks or trademarks of the
Microsoft Corporation in the United States and/or other countries.
Intel®, Core™, Core 2 Duo®, and Pentium® are the registered
trademarks or trademarks of the Intel Corporation in the United
States and other countries.
AMD and Athlon™ are either registered trademarks or
trademarks of AMD in the United States and other countries.
Macintosh, Mac OS are either registered trademarks or trademarks
of Apple Inc. in the United States and/or other countries.
YouTube is a trademark of Google Inc.
Flickr is a trademark of Yahoo.
Facebook is a trademark of Facebook Inc.
Twitter is a trademark of Twitter Inc.
Picasa is a trademark of Google Inc.
Adobe, the Adobe logo, and Adobe Acrobat are either registered
trademarks or trademarks of Adobe Systems Incorporated in the
United States and/or other countries.
HDMI, the HDMI logo and the term
"High Definition Multimedia Interface"
Before using this camcorder
•
•
This camcorder records video in H.264 (MPEG4/AVC) format.
You can play back and edit the video recorded by the
camcorder on a personal computer using the internal
software of this camcorder.
Please note that this camcorder is not compatible with other
digital video formats.
Before recording important video, make a trial recording.
Play back your trial recording to make sure the video and audio
have been recorded properly.
Recorded contents may be lost due to a mistake when handling
this camcorder or memory card, etc. Samsung will not provide
compensation for damages due to the loss of recorded contents.
Make a backup of important recorded data.
Protect your important recorded data by copying the files to
a PC. We also recommend you copy it from your PC to other
recording media for storage. Refer to the software installation and
USB connection guide.
Copyrights: Please note that this camcorder is intended for
individual use only.
Data recorded on the storage media in this camcorder using
other digital/analog media or devices is protected by the
Copyright Act and cannot be used without permission of the
owner of the copyright, except for personal enjoyment. Even if
you record an event such as a show, performance, or exhibition
for personal enjoyment, we strongly recommend that you obtain
permission beforehand.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
are trademarks or registered
trademarks of HDMI Licensing LLC.
Proper recording etiquette
•
Do not record videos or photos of people without their
authorization or consent.
•
•
Do not record videos or photos in forbidden recording places.
Do not record videos or photos in private places.
3
Safety information
The safety precautions illustrated below are to prevent personal injury or material damages. Heed all instructions carefully.
WARNING
Prohibited action.
Do not touch the product.
Means that there is a potential
risk of serious personal injury.
CAUTION
Do not disassemble the product.
Unplug from the power supply.
This precaution must be
followed.
Means that there is a potential
risk of personal injury or damage
to the product.
WARNING
Do not overload outlets or extension
cords as this may result in abnormal
heat or fire.
Using the camcorder at temperatures
over 60˚C (140˚F) may result in
fire. Keeping the battery at a high
temperature may cause an explosion.
Do not allow water, metal, or
inflammable material to enter the
camcorder or power adaptor. Doing
so may pose a fire hazard.
No sand or dust! Fine sand or dust
entering the camcorder or power
adaptor could cause malfunctions or
defects.
No oil! Oil entering the camcorder or
power adaptor could cause electric
shock, malfunctions or defects.
Do not aim the camcorder directly
into the sun. Doing so could cause
eye injuries, as well as lead to
malfunctioning of internal parts of the
product.
Do not bend the USB cable or damage
the power adaptor by pressing on it
with a heavy object. There is a risk of
fire or an electric shock.
Do not disconnect the adaptor by
pulling on its USB cable, as this could
damage the cable.
4
Safety information
Do not use the power adaptor if it
has damaged, split or broken cords
or wires. Doing so may cause fire or
electric shock.
Do not connect the power adaptor
unless the plug can be fully inserted
with no part of the blades exposed.
Do not dispose of the battery in a fire
as it may explode.
Never use cleaning fluid or similar
chemicals to clean the camcorder.
Do not spray cleaners directly on the
camcorder.
Keep the camcorder away from water
when using it near the beach or pool
or when it rains. There is a risk of a
malfunction or an electric shock.
Keep the used lithium battery or
memory card out of the reach of
children. If the lithium battery or
memory card is swallowed by a child,
consult a physician immediately.
Do not plug or unplug the power
adaptor with wet hands. There is a risk
of electric shock.
Keep the power adaptor unplugged
when not in use or during lightning
storms. There is a risk of fire.
Unplug the power adaptor before you
clean it. If you leave it plugged in, there
is a risk of a malfunction or an electric
shock.
If the camcorder emits an abnormal
sound or smell, or smokes, unplug
the power adaptor immediately and
request service from a Samsung
service center. There is a risk of fire or
personal injury.
If the camcorder malfunctions,
immediately detach the power adaptor
or battery from the camcorder.
There is a risk of fire or injury.
Do not attempt to disassemble, repair,
or modify the camcorder or the power
adaptor. There is a risk of fire or an
electric shock.
5
Safety information
CAUTION
Do not press the surface of the LCD
with force, or hit it with a sharp object.
If you push the LCD surface, display
unevenness may occur.
Do not drop or expose the camcorder,
battery, power adaptor or other
accessories to severe vibrations or
impact. This may cause a malfunction or
injury.
Do not use the camcorder on a tripod
(not supplied) in a place where it is
subject to severe vibrations or impact.
Do not use the camcorder near direct
sunlight or heating equipment. This may
cause a malfunction or injury.
Do not leave the camcorder in a closed
vehicle for a long time where the
temperature is very high.
Do not expose the camcorder to soot
or steam. Thick soot or steam could
damage the camcorder case or cause a
malfunction.
Do not use the camcorder near dense
exhaust gas generated by gasoline or
diesel engines, or corrosive gas such
as hydrogen sulphide. Doing so may
corrode the external or internal terminals,
disabling normal operation.
Do not expose the camcorder to
insecticide. Insecticide entering the
camcorder could cause the product
to fail to operate normally. Turn the
camcorder off and cover it with vinyl
sheet, etc. before using insecticide.
Do not expose the camcorder to sudden
changes in temperature or high humidity.
There is also a risk of defect or electric
shock when using outdoors during
lightning storms.
Do not place the camcorder down on
the open LCD screen.
Do not wipe the camcorder body with
benzene or thinner. The exterior coating
could peel off or the case surface could
deteriorate.
Do not leave the LCD screen open when
not using the camcorder.
6
Safety information
Do not hold the camcorder by the LCD
screen when lifting it. The LCD screen
could detach and the camcorder may
fall.
Do not use the camcorder near a TV or
radio. Interference from the camcorder
could cause noise on the TV or in the
radio broadcast.
Do not use the camcorder near
sources of strong radio waves or
magnetic fields such as speakers
and large motors. Noise from these
sources could distort the video or
audio you are recording.
Use Samsung-approved accessories
only. Using products from other
manufacturers may cause overheating,
fire, explosion, electric shock or
personal injuries caused by abnormal
operation.
Place the camcorder on a stable
surface that is well ventilated.
Keep important data separately.
Samsung is not responsible for data
loss.
Only plug the power adaptor plug into
a socket that is easily accessible. If any
problem occurs with the product, you
must pull the plug out of the socket
to disconnect the power completely.
Turning off the power button on
the product does not turn off the
camcorder completely.
Other manufacturers of optional
accessories compatible with this
camcorder are responsible for their
own products. Use the optional
accessories according to the safety
instructions. Samsung is not
responsible for any malfunction, risk of
fire, electric shock, or damages
caused by using unauthorized
accessories.
7
Contents
Before reading this user manual ....................... 2
SAFETY WARNINGS..................................................................... 2
PRECAUTIONS ............................................................................. 2
IMPORTANT INFORMATION ON USE ........................................... 2
RECORDABLE TIME AND CAPACITY ......................................... 33
ATTACHING THE STRAP............................................................. 34
ADJUSTING THE LCD SCREEN.................................................. 34
Basic recording ............................................. 35
RECORDING VIDEOS.................................................................. 35
RecordING pause/RESUME ....................................................... 36
TAGGING AND CAPTURING GREAT MOMENTS WHILE
Safety information............................................ 4
Quick start guide ........................................... 10
RECORDING (MY CLIP FUNCTION).......................................... 37
RECORDING PHOTOS................................................................ 38
RECORDING WITH EASE FOR BEGINNERS (SMART AUTO)...... 39
Zooming in/out............................................................................ 40
USING THE BACK LIGHT BUTTON............................................. 41
Getting to know the camcorder...................... 13
unpacking ................................................................................... 13
LOCATION OF CONTROLS......................................................... 14
IDENTIFIYING THE SCREEN DISPLAYS...................................... 16
Getting started .............................................. 19
INSERTING/EJECTING THE BATTERY........................................ 19
CHARGING THE BATTERY ......................................................... 20
CHECKING THE BATTERY STATE............................................... 21
Basic operation of the camcorder................... 24
TURNING YOUR CAMCORDER ON/OFF.................................... 24
SWITCHING TO THE POWER SAVING MODE ............................ 24
SETTING THE DATE/TIME FOR THE FIRST TIME........................ 25
SETTING THE OPERATION MODES ........................................... 26
SWITCHING THE INFORMATION DISPLAY MODE...................... 26
USING THE SHORTCUT MENU (OK GUIDE)............................... 27
SELECTING THE LANGUAGES................................................... 29
video ........................................................................................... 46
Getting ready to start recording ...................... 30
INSERTING AND EJECTING A MEMORY CARD
(NOT SUPPLIED)......................................................................... 30
SELECTING A SUITABLE MEMORY CARD (NOT SUPPLIED)...... 31
8
Quick start guide
This quick start guide introduces the basic operation and features of your camcorder. See the reference pages for more information.
STEP 1: Get ready
STEP 2: Record videos and photos
Insert the battery into the battery slot. page 19
Open the LCD screen and press the [Power ( )] button to turn
on the camcorder.
1
1
•
Set the [Lens cover open/close] switch to open ( ).
page 15
Charge the battery fully. page 20
2
To record videos, press the [Recording start/stop] button or,
to record photos, press the [PHOTO] button. pages 35, 38
2
Insert a memory card. page 30
3
CARD
[Recording
start/stop]
button
CAD
[Recording
start/stop]
button
10
Quick start guide
Viewing on a TV
STEP 3: Play back videos or photos
You can enjoy detailed, brilliant quality videos on a connected TV.
pages 81~83
Viewing videos or photos on the LCD screen
You can find recordings quickly by using the thumbnail view.
C
A
D
STEP 4: Save recorded videos / photos
Press the [MODE] button to select the playback (
) mode.
1
2
Using the Intelli-studio program built in to your camcorder, you can
import videos and photos into your computer and edit or share
the videos and photos with your friends and family. For details, see
pages 86~89.
Select the video or photo thumbnail view by using the [Zoom]
lever.
Use the [Control (Up/Down/Left/Right)] button to select a
desired video or photo, and then press the [Control (OK)]
button.
3
Normal
C
D
0:00:55
1/10
Photo
Move
Play
11
Quick start guide
Importing and viewing videos/photos to your PC from
the camcorder
Sharing videos/photos on Web sites
Share your contents with the world by uploading photos and
videos directly to a web site with a single click.
Click the Share (
page 89
) Upload tab on the Intelli-studio browser.
Start the Intelli-studio program by connecting the camcorder to
your PC with a USB cable.
1
•
A new file saving screen appears with the Intelli-studio main
window. Click Yes, and the uploading procedure starts.
Intelli-studio runs automatically when you connect the
camcorder to a Windows computer (if you have set PC
Software: On). page 79
Any new files are saved to your PC and registered to
Contents Manager in the Intelli-studio program.
2
•
You can arrange the files by different criteria such as Face,
Date, Location, etc.
STEP 5: Delete videos or photos
Contents Manager
Saved files in your PC
If the camcorder’s storage media is full, you cannot record new
videos or photos. Delete videos or photos you have saved to your
computer from the camcorder’s storage media. Then you can
record new videos or photos on newly freed up space.
[MODE] button Playback (
) mode [MENU] button
Delete page 70
Folders directory on your PC
Double-click the file you would like to play back.
3
12
Getting to know the camcorder
Check your accessories
UNPACkING
Your new camcorder comes with the accessories shown on this
page. If any of these items is missing from your box, call Samsung’s
Customer Care Center.
Battery
(IA-BP105R: AD43-00201A)
(IA-BP210R: AD43-00200A)
Power adaptor
(AD44-00196A)
USB cable
(AD39-00169A)
Quick start guide
Audio/Video cable
(AD68-07573A)
(AD39-00184A)
Model name
Lens
Internal memory
HMX-F90
HMX-F91
HMX-F900
HMX-F910
HMX-F920
Optional accessories
52x (Optical),
70x (Intelli),
130x (Digital)
-
•
Although the models have some features that are different, they
operate in the same way.
Micro HDMI cable
(AD39-00179A)
Carrying case
(AD69-00929A)
•
•
•
The exact appearance of each item may vary by model.
The contents may vary depending on the sales region.
You can purchase parts and accessories after consulting with your
local Samsung dealer. SAMSUNG is not responsible for reduced
battery life time or malfunctions caused by any unauthorized use of
accessories such as the power adaptor or the batteries.
A memory card is not included. See page 31 for memory cards
compatible with your camcorder.
•
External battery charger
Memory card/
Memory card adaptor
(IA-BC9UA4)
13
Getting to know the camcorder
LOCATION OF CONTROLS
Front & Left
1
2
3
Lens
1
MENU button
Control (Up/Down/Left/Right/OK) button /
Zoom (T/W) button
8
9
10 11
12
4
5
6
Recording start/stop button
LCD screen
Memory card/Jack cover
USB jack (
)
ⓐ
ⓑ
ⓒ
ⓓ
ⓔ
Memory card slot (
AV jack (
CHG (charging) indicator
HDMI jack (
)
)
2
3
4
)
7
8
Internal speaker
5
6
7
Display ( ) button
9
Recording pause/resume ( ) button
CARD
10
11
12
Back light ( ) button / SMART BGM button
SMART AUTO (
) button / Share ( ) button
ⓓ ⓔ
ⓑ ⓒ
Power ( ) button
ⓐ
14
Getting to know the camcorder
Right/Top & Bottom
Rear
1
2
3
9
1
2
7
6
3
4
5
8
Mode indicator
: Recording mode (Video/Photo)
: Playback mode
Recording start/stop button
Battery slot
1
2
3
4
5
6
7
8
9
1
MODE button
Zoom lever (T/W)
PHOTO / My Clip button
Strap
2
3
Strap hook
Be careful not to cover the internal microphone and lens during
recording.
Lens cover open ( )/close ( ) switch
Internal microphone
Battery release switch (BATT.)
Tripod receptacle
15
Getting to know the camcorder
IDENTIFIYING THE SCREEN DISPLAYS
The available functions vary depending on the selected operation mode. Different indicators appear depending on the setting values.
•
•
The On Screen Display (OSD) below appears when the camcorder is in the recording (
) mode only.
Press the [MODE] button to select the recording (
) mode. page 26
Video and Photo recording mode
Left of the LCD screen
Right of the LCD screen
STBY
0:00:00
[220Min]
9999
1 Sec/ 24 Hr
Indicator
Meaning
Indicator
Meaning
Recording mode (Video/Photo)
Storage media (memory card)
/
1/60
+0.3
Operating status (standby/
Battery info.
STBY
//
/
recording/pause/photo capturing)
Time counter (video recording
time, remaining recordable time)
(remaining battery level)
0:00:00 [220Min]
Photo Resolution, Video Resolution
Anti-Shake (HDIS)
Back light
,
JAN/01/2013 12:00AM
iSCENE / Smart Auto
Time Lapse REC
My Clip
/
•
This camcorder provides one combined
video and photo recording mode. You can
easily record videos or photos in the same
mode without having to change it.
The on-screen indicators are based on a 16GB
SDHC memory card.
The settings of functions marked with a are
lost when the camcorder turns off.
For enhanced performance, the display
indications and their order are subject to change
without prior notice.
Continuous shot
Photo image counter
(total number of recordable photos)
9999
Face Detection
•
•
•
White Balance
Manual focus
C.Nite
1/60
+0.3
•
•
The total number of recordable photos is based
on the available space on the storage media.
The maximum number the photo counter can
display is 9,999.
EV (Exposure Value)
Zoom (optical zoom / intelli zoom
/ digital zoom)
Digital Special Effect
16
JAN/01/2013 12:00AM Date/Time Display
Getting to know the camcorder
•
•
The On Screen Display (OSD) below appears in the video playback (
Press the [MODE] button to select the playback ( ) mode. page 26
) mode only.
Video playback mode: Thumbnail view
Top of the LCD screen
Center of the LCD screen
Normal
Indicator
Meaning
Indicator
Meaning
Recorded time
0:00:55
1/10
0:00:55
Video playback mode
Current video / total number of
recorded videos
Storage media (memory card)
1/10
Battery info
(remaining battery level)
Protect
Share Mark
My Clip
Photo
Move
Play
Bottom of the LCD screen
Error file
Indicator
Meaning
Button guide
Scroll bar
Video playback mode: Single view
Top of the LCD screen
0:00:00/0:00:55
Indicator
Meaning
Indicator
Meaning
My Clip
Video playback mode
Share Mark
Protect
Playback status (playback/pause/
search)
Time code (elapsed time /
recorded time)
/
/
/
0:00:00/0:00:55
Shortcut menu
100-0001
Storage media (memory card)
Thumbnail View
Bottom of the LCD screen
Battery info
(remaining battery level)
Indicator
Meaning
Button guide
File name (file number)
PlayOption
17
Video Resolution
100-0001
Getting to know the camcorder
•
•
This On Screen Display (OSD) below appears in the photo playback (
Press the [MODE] button to select the playback ( ) mode. page 26
) mode only.
Photo playback mode: Thumbnail view
Top of the LCD screen
Center of the LCD screen
Normal
Indicator
Meaning
Indicator
Meaning
1/10
Photo playback mode
Current photo / total number of
recorded photos
1/10
Storage media (memory card)
Protect
Battery info
(remaining battery level)
Movie
Move
Play
Error file
Scroll bar
Bottom of the LCD screen
Indicator
Meaning
Button guide
Photo playback mode: Single view
Top of the LCD screen
1/10
Indicator
Meaning
Indicator
Meaning
Protect
Photo playback mode
Slide Show
Shortcut menu
Current photo / total number of
recorded photos
1/10
Bottom of the LCD screen
Thumbnail View
100-0001
Storage media (memory card)
Indicator
Meaning
Button guide
File name (file number)
Battery info
(remaining battery level)
100-0001
Photo Resolution
18
Getting started
INSERTING/EJECTING THE BATTERY
To insert the battery
To eject the battery
Insert the battery into the battery slot until it softly clicks.
Gently push the [Battery release (BATT.)] switch in the direction
1
2
•
Make sure that the SAMSUNG logo on the battery is facing you
when the camcorder is placed as shown in the figure.
shown in the figure to eject the battery.
Push down, and then lift the battery out in the direction shown in
the figure.
[Battery release (BATT.)] switch
•
•
•
•
Use only Samsung-approved batteries. Do not use batteries from other manufacturers. Otherwise, there is a danger of overheating, fire, or explosion.
Samsung is not responsible for the problems caused by unapproved batteries.
Remove the battery from the camcorder when the camcorder is not in use.
We recommend you purchase one or more additional batteries to allow continuous use of your camcorder.
19
Getting started
Insert the battery into the camcorder. page 19
1
2
3
CHARGING THE BATTERY
Open the jack cover of the camcorder.
You can charge the battery with the USB cable and power adaptor.
Charge the battery using the USB cable and power adaptor.
Make sure that you use the supplied USB cable or power adapter
to charge the battery. If you use any other power adapter for the
camcorder, it will not work properly or the battery may not be
charged. It may also cause an electric shock or result in a fire.
•
The CHG (charge) indicator lights up and charging starts.
When the battery is fully charged, the charging (CHG)
indicator turns green. page 21
•
•
•
Charging the battery at low temperature may take longer or the
battery may not charge fully (The green indicator will not turn on).
Make sure that there are no foreign substances on the plug or in the
socket when you connect the power adaptor to the camcorder.
When using the power adaptor, place it close to the wall outlet. If
you experience a malfunction while using the camcorder, separate
the power adaptor immediately from the wall outlet.
To charge the battery with the power adaptor
•
•
Do not use the power adaptor in a tight space, such as between
furnishings.
Make sure to turn off the camcorder before disconnecting the power
adaptor. Otherwise, you can damage the storage media or data.
•
•
•
When recording indoors with a wall outlet available, it is convenient to use
the power adaptor instead of the battery.
We recommend you charge the battery in a place with an ambient
temperature between 50˚F and 86˚F (10°C~30°C).
If the camcorder is turned on, the battery will still charge, but more
charging time will be needed. We recommend you keep the camcorder
turned off while it charges.
To charge the battery by connecting to a PC
•
•
•
You cannot operate the camcorder using USB power only. Use the
power adaptor or battery to power the camcorder.
If you use the camcorder while you are charging the battery, charging
may take longer.
An AC plug adaptor is required in some foreign countries. If you need
one, purchase it from your distributor.
20
Getting started
Battery level display
CHECkING THE BATTERY STATE
The battery level display shows the amount of battery power
remaining in the battery.
You can check the charging state and remaining battery capacity.
To check the charging state
STBY
[220Min]
9999
The color of the CHG lamp indicates the charging state.
Battery Level
Indicator
State
Message
Fully charged
75%~50%
50%~25%
25%~5%
-
-
-
-
-
CA
Charging (CHG) lamp
less than 5%
Charging
state
Charging
(Orange)
Fully charged
(Green)
Error
Exhausted (flickers): The device will soon turn off.
Charge the battery as soon as possible.
-
Low
battery
(Orange blink)
LED color
-
The device will be forced to turn off after 3 seconds.
The figures above are based on a fully charged battery at normal
temperature. Low ambient temperature may affect the use time.
21
Getting started
Available charging and running time for the battery
Battery Type
IA-BP105R
IA-BP210R
approx. 300 min.
approx. 300 min.
SD
To charge the battery with the power adaptor
Charging time
approx. 160 min.
approx. 160 min.
To charge the battery by connecting to a PC
Resolution
Continuous recording time
Playback time
HD
approx. 100 min.
SD
HD
approx. 200 min.
approx. 400 min.
approx. 80 min.
approx. 160 min.
approx. 200 min.
•
•
•
Charging time: Approximate time in minutes required to fully charge a completely exhausted battery.
Recording/Playback time: Approximate time available when you have fully charged the battery.
The time is only for reference. Times shown above are measured under Samsung’s test conditions. Your times may differ, depending on
your usage and conditions.
•
•
The recording and playback times will be shorter when you use your camcorder in low temperatures.
We recommend using the power adaptor when using the Time Lapse REC function.
Continuous Recording (without zoom)
Using an AC power source
The continuous recording time shows the available recording time
when you record without using any other function after recording
starts.
The battery may discharge 1.5 times faster than this reference if you
use the record start/stop, the zoom, and the playback functions.
Prepare additional batteries with the expectation that the actual
recording time is about 60% of the times listed above.
We recommend that you use the power adaptor to power the
camcorder from a household AC outlet when recording and playing
back the camcorder indoors. The connection is the same as that for
battery charging. page 20
•
•
The charging time will vary depending on the amount of charge left in
the battery.
Depending on your PC specifications, the charging time can be
prolonged.
22
Getting started
About the battery
•
Battery properties
•
•
Check whether the battery terminal is damaged if the battery
falls or is dropped.
A lithium-ion battery is small-sized and has a high capacity. Low
ambient temperature (below 50ºF (10ºC)) may shorten its usage
time and affect its function. Before recording in low temperatures,
put the battery into your pocket to warm it, then install it in the
camcorder.
-
If you install a battery with the damaged terminal into the
camcorder, you can damage the camcorder.
Remove the battery and the memory card from the
camcorder and disconnect the power adaptor after use.
•
Make sure to store the battery separately after use.
-
Store the battery in a stable, cool, and dry place.
(Recommended temperature : 59ºF~77ºF (15ºC~25ºC),
recommended humidity: 40%~60%)
Temperatures that are too high or too low shorten the battery
lifetime.
The battery terminals can become rusty or malfunction if the
battery is stored in a smoky or dusty location.
-
A small amount of battery power is consumed when the
battery is stored in the camcorder even if the camcorder
power is off.
-
-
-
The battery may be completely discharged, if it has been
installed and left in the camcorder for a long period of time.
If this occurs, the battery may not fully operate even if you
charge it.
•
•
Recycle or dispose of your dead batteries properly.
-
If the battery is not used for a long time, fully charge the
battery and then, using your camcorder, drain the charge
completely. Do this once every 3 months to keep the battery
functioning properly. To store the battery, remove it from your
camcorder and put it in a cool, dry place.
The battery lifetime is limited.
-
-
Battery capacity decreases over time and through repeated
use. If decreased usage time between charges becomes
significant, it is probably time to replace the battery with a new
one.
Each battery’s life is affected by storage, and operating and
environmental conditions.
•
Charge an extra battery before using the camcorder
outdoors in cold temperatures.
-
The cold temperature may shorten the length of time you can
use the battery before needing to recharge it.
Carry the supplied USB cable and power adaptor to charge
the battery while travelling.
-
23
Basic operation of the camcorder
TURNING YOUR CAMCORDER ON/OFF
SWITCHING TO THE POWER SAVING MODE
If you need to use camcorder for the extended time, the following
functions enable you to prevent unnecessary energy consumption.
Open the LCD screen and press the [Power ( )] button to turn
on the camcorder.
1
Sleep mode
•
Set the [Lens cover open/close] switch to open ( ).
The camcorder switches to the sleep mode when the LCD screen
is closed, and then, if idle for more than 20 minutes, the camcorder
turns off. However, if Auto Power Off: 5 Min is set, the camcorder
turns off in 5 minutes.
To turn off the camcorder, press the [Power ( )] button.
2
If you open the LCD screen during sleep mode, the sleep mode
ends and the camcorder returns to the last operation mode used.
LCD screen is closed
After 20 minutes
<Sleep mode>
<Power off>
LCD screen
Power( ) button
•
•
The power saving mode does not work in the following situations:
- While recording, playing back, or displaying a slide show.
- When the LCD screen is opened.
The camcorder consumes less battery power in the power saving
mode. However, if you plan to use the camcorder for an extended
time, we recommend you turn off the camcorder by pressing the
[Power ( )] button when not using it.
The camcorder operates the self-diagnosis function when powered on.
If a warning message appears, refer to ‘warning indicators and
messages’ (pages 93~95) and take corrective action.
When using this camcorder for the first time
When you use your camcorder for the first time or reset it, the Date/
Time Set screen appears at start-up.
Set the date and time. page 25
24
Basic operation of the camcorder
SETTING THE DATE/TIME FOR THE FIRST
TIME
Internal rechargeable battery
•
Your camcorder includes a internal rechargeable battery that retains the
date and time settings even after the power is turned off.
Once this battery is depleted, the current date/time values are all reset
to defaults, and you need to recharge the internal rechargeable battery.
The date/time must be set again.
You can set the date and time of your local area when you turn on
this camcorder for the first time.
•
Charging the internal rechargeable battery
•
The internal battery is always recharged while your camcorder is
connected to the power adaptor or while the battery is attached.
If you do not connect the camcorder to power adaptor or do not attach
the battery for about 48 hours, the internal battery fully discharges. If
this occurs, charge the internal battery by connecting to the supplied
USB cable and power adaptor for 12 hours.
•
Open the LCD screen and press
the [Power ( )] button to turn on
the camcorder.
1
Date/Time Set
Month Day
JAN
01
Year
2013
Hr Min
12 00 AM
•
The Date/Time Set screen
appears.
Move
OK
Select the date and time
information, and change the setting values by using the [Control
(Up/Down/Left/Right)] button.
2
3
Make sure the clock is correctly set, and then press the [Control
(OK)] button.
•
•
•
The year can be set up to 2037.
Set Date/Time Display to On. page 76
After setting, the date and time are automatically recorded on a
special data area of the storage media.
25
Basic operation of the camcorder
SETTING THE OPERATION MODES
SWITCHING THE INFORMATION DISPLAY
MODE
You can switch the operation mode in the following order each time
you press the [MODE] button.
You can switch the on-screen information display mode.
Recording mode (
Each time the operation mode changes, the respective mode
indicator light turns on.
) Playback mode (
)
Press the [Display (
)] button.
•
•
The full and minimum display modes will alternate.
STBY
[220Min]
9999
STBY
Mode
Indicator
Functions
Recording
mode
To record videos or photos.
Playback
mode
To play back videos or photos.
<Minimum display mode>
<Full display mode>
This camcorder provides one recording mode for both video and photo
recordings. You can easily record videos or photos in the same mode
without having to switch modes.
•
•
Warning indicators and messages may appear depending on the
recording conditions.
In the menu screen, the [Display (
)] button will be deactivated.
26
Basic operation of the camcorder
Press the [Control (Left)] button to
select EV function.
2
3
STBY
[220Min]
9999
USING THE SHORTCUT MENU (Ok GUIDE)
The shortcut menu (OK guide) contains the most frequently
accessed functions for the selected mode. Pressing the [Control
(OK)] button will display the shortcut menu of frequently used
functions on the LCD screen.
•
Press the [Control (Left/Right)]
button to adjust the exposure
while viewing the image on the
LCD screen.
EV
0.0
An example: Setting EV (Exposure Value) in the recording mode
using the shortcut menu (OK guide).
Press the [Control (OK)] button to
confirm your selection.
STBY
[220Min]
9999
•
Press the [Control (OK)] button
to exit the shortcut menu.
The exposure value setting is
+1.0
•
applied and the indicator (
and setting value appear.
)
•
•
The shortcut menu (OK guide) cannot be used in the SMART AUTO
mode.
The example above shows how to set EV in the recording mode
using the shortcut menu. The setting procedure could be different for
other menu items.
•
The shortcut menu appears briefly. The shortcut menu reappears
when you press the [Control (OK)] button.
Press the [Control (OK)] button in
STBY mode.
STBY
[220Min]
9999
1
•
The shortcut menu (OK guide)
appears.
27
Basic operation of the camcorder
Controlling the shortcut functions using the control buttons
Playback (
) mode
) mode
Photo playback (
Button
Menu selection
Recording (
) mode
) mode
Video playback (
Confirms selection
- Access the shortcut menu
- Confirm selection
- Access the shortcut menu
- Playback / Pause
- Access the shortcut menu
- Playback zoom
OK
- Exit the shortcut menu
- iSCENE
- Zoom (tele)
Increases the volume
Decreases the volume
-
-
Moves the cursor up
UP
- Focus
- Zoom (wide)
Moves the cursor
down
DOWN
LEFT
- Search playback RPS (Reverse
Playback Search) rate:
x2 x4 x8 x16
Moves to the previous
menu
EV
Previous image
Next image
→
→
→
- Previous skip playback
- Search playback FPS (Forward
Playback Search) rate:
Moves to the next
menu
Face Detection
→
→
→
x2 x4 x8 x16
- Next skip playback
RIGHT
28
Basic operation of the camcorder
SELECTING THE LANGUAGES
You can select the language that appears on the LCD screen.
Press the [MENU] button
1
STBY
[220Min]
[Control (Left/Right)] button
Settings.
Settings
Format
Default Set
Language
Press the [Control (Up/Down)]
button to select Language, and
then press the [Control (OK)]
button.
2
Exit
STBY
[220Min]
Settings
Format
English
Press the [Control (Up/Down)]
button to select the desired OSD
language, and then press the
[Control (OK)] button.
3
4
한국어
Default Set
Language
Français
Exit
Press the [MENU] button to exit the menu.
•
The OSD language appears in the selected language.
•
•
•
Language options may be changed without prior notice.
The selected language remains even if you remove the battery.
The date and time format may change depending on the language
you selected.
29
Getting ready to start recording
INSERTING AND EJECTING A MEMORY CARD (NOT SUPPLIED)
CARD
CARD
To insert a memory card
To eject a memory card
Turn the camcorder off.
Turn the camcorder off.
1
2
3
1
2
3
4
Open the memory card cover as shown in the figure.
Open the memory card cover as shown in the figure.
Gently push the memory card to eject it.
Insert the memory card into the card slot until it softly clicks.
• Make sure that the camcorder is placed as shown above and
the terminal portion of the card is facing up.
Pull the memory card out of the memory card slot and close the
cover.
Close the cover.
4
•
•
•
To avoid data loss, turn off the camcorder by pressing the [Power ( )] button before inserting or ejecting the memory card.
Be careful not to push the memory card too hard. The memory card may suddenly pop out.
If you eject the memory card from the camcorder while it is on, the camcorder turns off.
Your camcorder supports only SD, SDHC, and SDXC cards.
Card compatibility with this camcorder may vary depending on the card manufacturer and type.
30
Getting ready to start recording
SELECTING A SUITABLE MEMORY CARD
(NOT SUPPLIED)
Compatible memory cards
•
You can use SD, SDHC, and SDXC cards with this camcorder.
We recommend you use an SDHC card. This camcorder
supports SD cards up to 2GB. We cannot guarantee normal
operation with SD cards bigger than 2GB.
Usable memory card
Terminals
•
•
MMC (Multi Media Card) and MMC Plus are not supported.
Protection tab
Compatible memory card capacity:
- SD: 1GB~2GB
- SDHC: 4GB~32GB
- SDXC: ~up to 64GB
SD
(1GB~2GB)
SDHC
(4GB~32GB)
SDXC
(Up to 64GB)
•
•
•
•
When you use unauthorized memory cards, the camcorder can
not record videos correctly and your recordings may be lost.
The memory cards released after this camcorder was released
may not be compatible with the camcorder.
Using the memory card adaptor
To use a micro memory card with a computer or a card
reader you must attach it to or insert it into an adaptor.
To ensure stable recording and playback, use 6MB/s (Class 6) or
higher memory cards.
SD/SDHC/SDXC memory cards have a mechanical write-
protection switch. Setting the switch prevents accidental erasure
of files recorded on the card. To enable writing, move the switch
up in the direction of the terminals. To set write protection, move
the switch down.
•
•
SDHC/SDXC cards are a higher version of SD memory cards and
support higher capacities than SD memory cards.
SD cards can be used with current SD enabled host devices.
31
Getting ready to start recording
Handling a memory card
The camcorder supports SD, SDHC, and SDXC memory
cards, giving you a wider choice of cards!
•
Damaged data may not be recoverable. We recommend you
make a back-up of important data separately on the hard disk of
your PC.
The data storage speed of cards may differ, depending on the
manufacturer and production system.
•
•
•
Turning the power off or removing a memory card during an
operation such as formatting, deleting, recording, and playback
may cause data loss.
If you modify the name of a file or folder stored in the memory
card with your PC, your camcorder may not recognize the
modified file.
The memory card does not support any data recovery mode.
Therefore, care should be taken to prevent the memory card from
being damaged while recording.
•
•
SLC (single level cell) system: faster write speed enabled.
MLC (multi level cell) system: only lower write speed is
supported.
For best results, we recommend using a memory card that
supports a faster write speed.
Using a lower write speed memory card for recording video may
cause difficulties when storing.
You may even lose your video data during the recording. In an
attempt to preserve every bit of the recorded video on a low
speed card, the camcorder forcibly stores the video on the
memory card and displays a warning:
Low speed card. Please record at a lower resolution.
If you are unavoidably using a low speed memory card, the
resolution and quality of the recording may be lower than the
value you set. page 53
•
Make sure to format the memory card on this camcorder. If the
memory card had been formatted by a PC or other device, using
it on this camcorder without re-formatting may cause trouble
with recording and/or playback. Samsung is not responsible for
damage to recorded contents caused by improper formatting.
•
•
You have to format newly-purchased memory cards, memory
cards with data that your camcorder cannot recognize, or cards
with data saved by other devices. Note that formatting erases all
data on the memory card. Erased data cannot be recovered.
The higher the video resolution and quality, the more memory the
camcorder uses.
•
•
•
Samsung is not responsible for data loss due to misuse, including
loss caused by any PC virus.
We recommend using a memory card case to avoid data loss that
can be caused by moving the card or by static electricity.
After a period of use, the memory card may get warm. This is normal
and is not a malfunction.
A memory card has a certain life span. If you cannot record new
data, you have to purchase a new memory card.
•
•
Do not bend, drop, or subject the card to strong impacts.
Do not place foreign substances on the memory card terminals.
Use a soft dry cloth to clean the terminals if required.
•
Do not paste anything other than the label provided with the card
on the label pasting area of the card.
•
•
Do not use a damaged memory card.
Be careful to keep the memory card out of the reach of children,
who might swallow it.
32
Getting ready to start recording
•
Your recordable time and capacity and recordable number of photos
may differ from the figures in the tables depending on your subject
and actual recording conditions.
RECORDABLE TIME AND CAPACITY
•
•
The higher the resolution, the more memory is used.
Lower resolution increases the recording time, but the image quality
may suffer.
Recordable time available for video
•
The bit rate automatically adjusts to the recording image.
Accordingly, the recording time may vary.
Storage media capacity
Resolution
1GB 2GB 4GB 8GB 16GB 32GB
•
•
Memory cards bigger than 64GB may not operate normally.
The recording length of a Time Lapse REC may vary depending on
settings.
A memory card that is used to store a video can have un-writable
areas, which may result in reduced recording time and free memory
space.
The maximum continuous recording time is under 20 minutes. The
maximum video file size is 1.8GB. When a video recording time is
more than 20 minutes or a video file exceeds 1.8GB, a new video file
is created automatically.
64GB
1280X720/30p
720X480/60p (16:9)
720X480/60p (4:3)
13
13
13
27
27
27
55
55
55
110
110
110
220
220
220
440
440
440
890
•
•
890
890
(Unit: Approximate minutes of recording)
•
•
The maximum number of recordable photo and video files is 9,999,
respectively.
Resolutions marked with are the resolutions of photos you record
Recordable number of photos
Storage media capacity
when you set video resolution to 720X480/60p (4:3).
Resolution
1GB 2GB 4GB 8GB 16GB 32GB
64GB
1696x954 (16:9)
1280x720 (16:9)
1,650 3,290 6,630 9,999 9,999 9,999
9,999
2,270 4,550 9,160 9,999 9,999 9,999
1,520 3,030 6,110 9,999 9,999 9,999
9,999
9,999
1600x1200 (4:3)
800x600 (4:3)
2,990 5,970 9,999 9,999 9,999 9,999
9,999
(Unit: Approximate number of images)
≒
1GB 1,000,000,000 bytes : Actual formatted capacity may be
33
less as the internal firmware uses a portion of the memory.
Getting ready to start recording
ADJUSTING THE LCD SCREEN
ATTACHING THE STRAP
Adjust the length of strap so that the camcorder is stable when you
press the [Recording start/stop] button with your thumb.
The wide LCD screen on your camcorder offers high quality image
viewing.
Open the LCD screen with your finger.
1
If you adjust the strap too tightly and use excessive force to insert your
hand, the strap hook of the camcorder may be damaged.
•
The screen opens up to 90°.
Rotate the LCD screen towards the lens.
2
•
You can rotate it up to 180° towards the lens and up to
90° backwards. To view recordings more conveniently, rotate
the screen by 180° towards the lens, and then fold it back to
the body.
1
2
Excessive rotation may damage the connective hinge between the
screen and the camcorder.
•
When the LCD screen is rotated by 150°~180°, the left and right
sides of the subject are shown in reverse, which produces a
horizontally flipped image.
•
•
Remove fingerprints or dust on the screen with a soft cloth.
To adjust the LCD brightness, see page 77.
34
Basic recording
Select a subject to record.
0:00:00
[220Min]
0005
1
RECORDING VIDEOS
•
Adjust the LCD screen to the
best angle for recording.
Set the desired resolution before recording. page 53
•
Use the [Zoom] lever or [Zoom]
button to adjust the size of the
subject. page 40
•
•
Insert a memory card. page 30
Open the Lens cover by using the [Lens cover open/close]
switch. page 15
•
•
Press the [Power ( )] button to turn on the camcorder.
Press the [Recording start/stop] button.
2
3
Select the recording (
) mode by pressing the [MODE]
•
The recording () indicator appears and recording starts.
button. page 26
To stop recording, press the [Recording start/stop] button
again.
This camcorder features two [Recording start/stop] buttons. One
is on the rear side of the camcorder and the other is on the LCD
screen. Select the one that works best for you.
•
•
If power is interrupted or an error occurs during recording, the video
may not be recorded.
Samsung is not responsible for any damage caused by a failure of
normal recording or playback operations caused by memory card
error.
•
•
Note that damaged data cannot be recovered.
Do not turn off the camcorder or remove the memory card while
accessing the storage media. Doing so may damage the storage
media or the data in the storage media.
35
Basic recording
RECORDING PAUSE/RESUME
•
•
•
For on-screen information display, see pages 16~18.
For approximate recording times, see page 33.
Eject the battery when you have finished recording to prevent
unnecessary battery power consumption.
For various functions available when you record videos, see pages
52~66.
During recording, some button operations are unavailable. ([MODE]
The camcorder allows you to pause temporarily while recording a
video. With this function, you can record separate scenes as a single
video.
•
•
•
button, [MENU] button, etc.)
Sound is recorded from the internal stereo microphone on the
top-front of the camcorder. Take care that this microphone is not
blocked.
•
•
Before recording an important video, make sure to test the recording
function to check if there is any problem with the audio or video
recording.
You can adjust the brightness of the LCD screen in the menu
options. Adjusting the LCD screen does not affect the image being
recorded. page 77
•
•
You cannot use a locked memory card for recording. You will see a
message saying recording is disabled due to the lock.
Recording videos in a quiet environment increases microphone
sensitivity. This increased sensitivity may cause the microphone
to record surrounding ambient noise. The increased microphone
sensitivity may also cause the camcorder to record the noise the
zoom mechanism makes if you use the zoom while recording.
When you record indoors or in the dark places, ISO sensitivity is
automatically adjusted. In very dark places, the ISO adjustment
can cause interference effects on images and prevent you from
recording these images correctly. We recommend you use a
professional, infrared camcorder when recording in dark places or at
night.
An image can be blurred when the Anti-Shake(HDIS) function is
enabled and the camcorder is mounted on a tripod or fixed in place.
Release the Anti-Shake(HDIS) function when the camcorder is
mounted on a tripod.
Press the [Recording start/stop]
button.
1
0:01:24
[220Min]
0005
•
The recording () indicator
appears and recording starts.
Stop
Press the [Recording pause/
resume ( )] button.
Resume
2
•
•
•
•
The recording pauses and the indicator ( ) appears.
To continue the recording, press the [Recording pause/
resume ( )] button.
•
•
If you connect your camcorder to a PC using a USB cable when
recording is paused, the camcorder will connect to the PC after it
saves the video it has recorded up to the pause.
If you remove the memory card when the camcorder is in Pause
mode, the camcorder turns off the power and will not save any of the
video it has recorded.
36
Basic recording
TAGGING AND CAPTURING GREAT
MOMENTS WHILE RECORDING
(MY CLIP FUNCTION)
Understanding My Clip function
Captured photos are saved in the photo thumbnail view.
My Clip lets you tag good scenes with the My Clip icon ( ) by
pressing the [PHOTO] button while you are recording a video, and
then lets you extract those clips from the video and watch them
separately. The camcorder also captures photos at the same time.
During a video
recording
You can extract and play back the scenes tagged as
‘My Clip’( ) from a video. page 45
•
•
The camcorder can tag up to 5 moments as ‘My Clip’ and capture
up to 5 photos while recording a video.
Press the [Recording start/stop] button.
1
When you use the My Clip function, the camcorder tags the scene
so that it starts 3 seconds before you pressed the [PHOTO] button
and ends five seconds after you pressed the [PHOTO] button.
Photos are captured in the video recording resolution.
When you use time lapse recording, the My Clip function does not
operate.
You can also tag any scenes in a video by pressing the [PHOTO]
button during video playback. page 46
The captured photos are not recorded if an error occurs during
video recording or the camcorder does not complete recording
successfully.
•
The recording () indicator appears and recording starts.
Press the [PHOTO] button at each
great moment while recording.
2
[220Min]
0005
•
•
•
The camcorder tags the scenes
as My Clip ( ) and captures
photos at the same time.
•
•
To stop recording, press the
[Recording start/stop] button again.
3
37
Basic recording
Center the subject in the LCD
screen.
2
3
RECORDING PHOTOS
Set the desired resolution before recording. page 54
Fully press the [PHOTO] button.
•
•
•
Insert a memory card. page 30
Open the Lens cover by using the [Lens cover open/close]
switch. page 15
The shutter sound is heard
(when Shutter Sound: On is
set).
•
•
Press the [Power ( )] button to turn on the camcorder.
Select the recording (
button. page 26
•
To continue capturing, wait until the current photo is
) mode by pressing the [MODE]
completely saved on the storage media.
Do not turn off the camcorder or remove the memory card when taking
photos as it may damage the storage media or data.
•
•
This camcorder provides one combined video and photo
recording mode. You can easily record videos or photos in the
same mode without having to change it.
The recordable number of photos varies depending on the photo
resolution. page 33
•
•
•
Audio is not recorded when you take photos.
For the on-screen display information, see pages 16~18.
You can adjust the brightness of the LCD screen in the menu
options. Adjusting the LCD screen does not affect the image being
recorded. page 77
•
•
For various functions available during recording, see pages 52~66.
Photo files conform to the DCF (Design rule for Camera File system)
standard, established by JEITA (Japan Electronics and Information
Technology Industries Association).
Select a subject to record.
1
•
•
Adjust the LCD screen to the best angle for capturing.
Use the [Zoom] lever or [Zoom] button to adjust the size of
the subject. page 40
38
Basic recording
RECORDING WITH EASE FOR BEGINNERS
(SMART AUTO)
Scene icons
Meaning
Appears when recording a night scene.
Appears when recording with a very bright background.
Appears when recording indoors.
User-friendly SMART AUTO optimizes your camcorder for the
recording conditions automatically, providing you with the best
performance.
Appears when recording a close-up.
Appears when recording a landscape.
Appears when recording a portrait.
Appears when recording a portrait outdoors at night.
Press the [Recording start/stop] button or [PHOTO] button.
pages 35, 38
3
4
To cancel the SMART AUTO mode, press the [SMART AUTO]
button again.
Press the [SMART AUTO] button.
STBY
[220Min]
9999
1
2
•
The SMART AUTO (
) and Anti-Shake(HDIS) (
) icons
•
The SMART AUTO (
Anti-Shake(HDIS) (
) and
) icons
disappear from the screen.
appear on the screen at the same
time.
•
•
When there is no detected scene, the (
The camcorder may not detect the Portrait mode when recording a
face, depending on the position of the face or brightness.
) icon appears.
Center the subject in the LCD
screen.
•
Depending on conditions such as lighting, shaking of the camcorder,
or distance to the subject, the camcorder may detect the image you
see on the LCD screen as a different scene type each time you apply
SMART AUTO.
•
The camcorder automatically detects the scene (Landscape,
etc.) and adjusts the camcorder settings accordingly.
The appropriate scene icon appears on the LCD screen.
•
•
•
The Portrait and Night Portrait modes work only when Face
Detection is set to On. page 56
Buttons unavailable during SMART AUTO operation:
[MENU] button, [Control (OK)] button, etc. Most settings are
automatically adjusted in SMART AUTO mode. To set or adjust
functions on your own, release the SMART AUTO mode first.
39
•
SMART AUTO must be set before recording.
Basic recording
ZOOMING IN/OUT
W: Wide-angle
T: Telephoto
Use the zoom function for close-up or wide-angle recording. This
camcorder allows you to record using 52x optical power zoom, 70x
Intelli-zoom and 130x digital zoom.
•
•
Zoom magnification over 70x is done through digital image
processing, and is therefore called digital zoom. Digital zooming is
possible up to 130x. page 62
To maintain sharp focus, the minimum possible distance between
the camcorder and subject is about 1cm (about 0.39 inch) for wide-
angle and 1m (about 39.4 inches) for telephoto.
•
•
Optical zoom preserves image quality, but the image quality may
suffer when you use digital zoom.
Fast zooming or zooming in a subject that is a good distance away
may cause the camcorder to focus slowly. If this occurs, use Focus:
Manual. page 58
To zoom in (T)
•
We recommend you use Anti-Shake(HDIS) for handheld recording
when the subject is zoomed in and enlarged.
Frequent use of the zoom function consumes more power.
If you zoom when recording, the camcorder may record the sound
Slide the [Zoom] lever towards [T] (telephoto).
(Or press the [Control (Up)] button on the LCD screen.)
•
•
•
The distant subject is gradually magnified.
of the [Zoom] lever or [Zoom] button operating.
•
When you use the zoom function, you can decrease its speed by
slowly moving the [Zoom (T/W)] lever. Moving the lever quickly
increases the zoom speed. However, you cannot use the [Zoom
(T/W)] button on the display to adjust the zoom speed.
To zoom out (W)
Slide the [Zoom] lever towards [W] (wide-angle).
(Or press the [Control (Down)] button on the LCD screen.)
•
When Video Resolution is set to 1280x720/30p, the Intelli Zoom
function does not operate.
•
•
The subject gets smaller and further away.
The smallest zoom ratio is the subject’s original size in the zoom-
out.
40
Basic recording
USING THE BACk LIGHT BUTTON
Back lighting influences recording when the subject is
darker than the background:
When a subject is lit from behind, this function compensates for
lighting so that the subject is not too dark.
•
•
•
•
•
The subject is in front of a window.
The subject is against a snowy background.
The subject is outdoors and the background is overcast.
The light sources are too bright.
The person to be recorded is wearing white or shiny clothes and
is placed against a bright background.
•
The person’s face is too dark to distinguish his/her features.
Press the [Back light (
between On and Off.
)] button to toggle the back light mode
<Backlight off>
<Backlight on>
41
Basic playback
CHANGING THE PLAYBACk MODE
•
•
•
You can switch to the playback mode by pressing the [MODE] button.
The recorded videos or photos appear in thumbnail view and the most recently created file is highlighted.
The camcorder selects the thumbnail display options based on the standby mode you used the last time. However, you can choose the
video or photo thumbnail view display options by using the [Zoom] lever.
Understanding how to change the operation modes
You can easily change the playback mode by using the buttons as shown in the following figures:
<Going to the standby mode
after recording a video>
<Video playback mode>
[220Min]
STBY
Normal
<Switch modes>
9999
0:00:55
1/10
Photo
Move
Play
<Going to the standby mode
after taking a photo>
<Photo playback mode>
[220Min]
9999
STBY
Normal
1/10
Movie
Move
Play
42
Basic playback
Use the [Control (Up/Down/Left/
Right)] button to select the desired
videos, and then press the [Control
(OK)] button.
0:00:00/0:00:55
2
PLAYING BACk VIDEOS
You can preview recorded videos in a thumbnail view, find your
desired video quickly, and play back directly.
•
The camcorder plays back the
video you selected and the
shortcut menu for playback
appears for a short time.
Thumbnail View
100-0001
•
•
Insert a memory card. page 30
Open the LCD screen and press the [Power ( )] button to turn
on the camcorder.
•
This function works only in the video playback (
page 26
) mode.
•
•
The selected videos play back according to the PlayOption
setting. page 68
If you play back a video tagged as My Clip, the My Clip
(
) icon on the LCD screen appears. The color of the My
Clip icon is changed to yellow at the scenes tagged as My
Clip (for 8 seconds).
To stop playback and return to the thumbnail view, use the
[Zoom] lever.
3
Do not power off the camcorder or eject the memory card during video
playback. Doing so may damage the recorded data.
•
•
The loading time of a video may vary depending on the video file's size
and video resolution.
Select the video thumbnail view.
1
Video files may not play back on the camcorder in the following cases:
Normal
055
1/10
-
-
The video was recorded on another device.
The video has a file format that is not supported by the camcorder.
•
You can easily switch between
video and photo thumbnail view
using the [Zoom] lever.
•
The internal speaker automatically turns off when the Audio/Video cable
is connected to the camcorder. (When the camcorder is connected to an
external device, adjust the volume using the connected external device.)
You can play back recorded video files on a TV or a PC. pages 81, 86
For various functions available during playback, see page 44.
•
•
Photo
Move
My Clip Play
43
Basic playback
Skip playback
Various playback operations
•
•
•
During playback, press the [Control (Right)] button to locate
the starting point of the next file. Pressing the [Control (Right)]
button repeatedly skips files in the forward direction.
During playback, press the [Control (Left)] button to locate the
starting point of the current file. Pressing the [Control (Left)]
button repeatedly skips files in the reverse direction.
[Control (Up/Down/Left/
Right/OK)] button
Press the [Control (Left)] button within 3 seconds from the
starting point of the current file to skip back to the previous file.
To adjust the volume during video playback
Press the [Control (Up/Down)] button
to increase or decrease the volume.
0:00:00/0:00:55
Playback/Pause/Stop
•
•
You can hear the recorded sound
from the internal speaker.
The level can be set anywhere
between 0 and 10.
Playback and pause alternate
when you press the [Control (OK)]
0:00:00/0:00:55
1
button during playback.
Thumbnail View
100-0001
Use the [Zoom] lever to stop
playback and return to the
thumbnail view.
2
0:00:00/0:00:55
Thumbnail View
100-0001
Search playback
100-0001
During playback, press and hold
the [Control (Left/Right)] button
0:00:00/0:00:55
1
•
•
•
If you close the LCD screen during playback, you may not hear the
sound from the speaker.
You can hear the recorded sound only when the playback is at
normal speed.
When playing back the My Clip tags, the search playback function
does not operate.
for reverse search/forward search.
Pressing the [Control (Left/Right)]
button repeatedly increases the
search speed for each direction.
2
3
100-0001
•
•
RPS (Reverse Playback Search) rate: x2
FPS (Forward Playback Search) rate: x2
x4
x4
x8
x8
x16
x16
44
To resume normal playback, press the [Control (OK)] button.
Basic playback
USING THE SMART BGM FUNCTION
PLAYING BACk MY CLIP
You can extract and play back the scenes tagged as ‘My Clip’ from
a video.
You can enjoy music during video playback. If the original sound in
the video is loud, the background music will be decreased naturally.
On the other hand, if the original sound in the video is quiet, the
background music will be increased naturally.
This function works only in the video playback (
) mode.
page 26
Select the video thumbnail view.
1
Normal
0:00:55
5/10
Use the [Control (Up/Down/Left/
Right)] button to select the video
tagged with the My Clip symbol
, and then press the [PHOTO]
button.
2
(
)
Photo
Move
My Clip Play
Select the desired video to play back and then press the [SMART
BGM] button.
0:00:00/0:00:55
•
The camcorder plays back the
tagged scenes sequentially.
•
To cancel, press the [SMART BGM] button again.
To stop playback and return to the
thumbnail view, use the [Zoom]
lever.
3
You can change the background music in the Smart BGM Option.
page 68
Thumbnail View
100-0005
45
Basic playback
When you see a scene you want to
3
4
TAGGING AND CAPTURING GREAT
tag, press the [PHOTO] button.
MOMENTS WHILE PLAYING BACk VIDEO
•
The camcorder tags the scenes
as My Clip ( ) and captures
photos at the same time.
You can tag good scenes during playback using the My Clip
function ( ) and capture photos from those scenes.
To stop playback and return to the
thumbnail view, use the [Zoom] lever.
•
During video playback, the camcorder can tag up to 20 scenes
with ‘My Clip’ from a video and capture photos until the available
remaining capacity of the storage media is full.
•
•
Photos are captured in the same resolution as the video recording.
If you press the [PHOTO] button while extracting and playing back
scenes tagged as My Clip, the camcorder switches to STBY mode.
Select the video thumbnail view.
1
Use the [Control (Up/Down/Left/
2
0:00:00/0:00:55
Right)] button to select the desired
videos, and then press the [Control
(OK)] button.
•
The camcorder plays back the
video you selected and the
shortcut menu for playback
appears for a short time.
Thumbnail View
100-0001
46
Basic playback
Use the [Control (Up/Down/
Left/Right)] button to select the
desired photos, and then press the
[Control (OK)] button.
2
3
1/10
VIEWING PHOTOS
You can view recorded photos by using various playback functions.
•
The camcorder displays the
•
•
Insert a memory card. page 30
Open the LCD screen and press the [Power ( )] button to turn
on the camcorder.
Thumbnail View
100-0001
photo you selected in full screen
view and the shortcut menu for
playback appears for a short time.
•
This function works only in the photo playback (
page 26
) mode.
•
To view the previous/next photo, press the [Control (Left/
Right)] button.
To return to the thumbnail view, use the [Zoom] lever.
Do not power off the camcorder or eject the memory card during photo
playback. Doing so may damage the recorded data.
•
•
Loading time may vary depending on the size and quality of the
selected photo file.
Your camcorder may not play back the following photo files normally:
-
-
Photos that were recorded on another device.
Photos recorded in a file format not supported by this camcorder
(a format that does not conform to DCF standards).
Select the photo thumbnail view.
1
Normal
1/10
•
You can easily switch between
the video and photo thumbnail
view using the [Zoom] lever.
Movie
Move
Play
47
Basic playback
Press the [Control (Up/Down/
Left/Right)] button to view the area
you want on the magnified photo.
3
4
x1.5
1/10
ZOOMING DURING PHOTO PLAYBACk
You can magnify a playback image by using the zoom function.
To cancel, use the [Zoom] lever.
Exit
100-0001
•
•
Photos recorded on other devices or those edited on a PC cannot
be magnified.
While you are using the playback zoom, you cannot select other
images.
Select the photo you want to
magnify. page 47
1
1/10
Adjust the magnification with the
[Control (OK)] button.
2
Thumbnail View
100-0001
•
The screen is framed and the
image is magnified starting from
the center of the image.
•
You can zoom in from x1.3 to x2.0.
48
Using the menu items
Press the [Control (Up/Down)] button to select the desired
submenu item, and then press the [Control (OK)] button.
3
4
HANDLING MENUS
The instructions below are examples of how to access and use
menu items using the [MENU] button. When you access and use
other menu items, use these examples as guides.
When you finish changing settings, press the [MENU button to
]
exit.
Press the [MODE] button to select the recording (
page 26
) mode.
•
•
While you are using certain menu items, some other menu items
cannot be used at the same time or may be grayed out. For more
information, see ‘Troubleshooting’ on page 102.
For easy understanding, the menu setting procedure in the example
above presented the simplest way of setting the menu item. Menu
setting methods can differ depending on the menu options you
choose.
•
You can also access the shortcut menu using the [Control (OK)]
button. page 27
Press the [MENU] button.
1
2
STBY
[220Min]
•
The menu screen appears.
Video Resolution
1280X720/30p
Press the [Control (Left/Right)]
button to select Video Resolution.
720X480/60p(16:9)
720X480/60p(4:3)
Exit
•
The Video Resolution function is
used here as an example.
49
Using the menu items
MENU ITEMS
•
•
The items available in each menu vary depending on the operation mode.
For item operation details, see the page number listed under Page in the table.
Recording menu items
Playback menu items
●
: Accessible
✕
: Not accessible
Video
playback
mode
Photo
playback
mode
Items
iSCENE
Default value
Page
52
53
54
54
56
57
58
58
60
61
62
63
64
66
75
Items
Default value Page
Auto
(
)
(
)
Video Resolution
Photo Resolution
White Balance
Face Detection
EV
1280X720/30p
Thumbnail View
Option
(Thumbnail view only)
1696x954 (16:9)
●
●
Normal
67
Auto
PlayOption
●
●
●
●
●
●
✕
●
●
✕
✕
●
✕
●
✕
●
●
●
Play All
68
68
70
71
72
73
74
74
75
Off
Smart BGM Option
(Single view only)
The Flea Waltz
-
C.Nite
-
Delete
Delete My Clip
Protect
-
-
-
-
-
-
-
Focus
Auto
Anti-Shake(HDIS)
Digital Special Effect
Zoom Type
Cont. Shot
Off
Off
Optical Zoom
Share Mark
Slide Show
File Info
Off
Off
Off
-
Time Lapse REC
Guideline
Settings
Settings
50
Using the menu items
●
✕
: Accessible
: Not accessible
Setting menu items
Recording
Playback mode (Thumbnail view)
Playback mode (Single view)
Items
Default values
Page
(
)
Video
Photo
Video
Photo
mode
●
Storage Info
File No.
-
Series
-
75
75
76
76
77
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
✕
●
●
●
●
●
●
●
●
●
●
●
●
●
✕
●
●
●
Date/Time Set
Date/Time Display
LCD Brightness
●
●
Off
●
Normal
●
●
●
●
●
●
●
●
●
On
77
Auto LCD Off
Beep Sound
Shutter Sound
On
On
78
78
5 Min
79
Auto Power Off
PC Software
Format
On
79
80
80
80
80
-
Default Set
-
Language
English
-
Open source licenses
•
•
•
•
Menu options and default values may be changed without prior notice.
There are some functions you cannot activate simultaneously in the menu. These items are grayed out. You cannot select the gray menu items.
In general, functions in both the thumbnail display and full image display employ the same methods, while their detailed options may be different.
Items marked with are available only when the camcorder is powered by the battery.
51
Advanced recording
iSCENE
Submenu Items
This camcorder automatically can set the shutter speed and
aperture according to the subject and brightness for optimum
recording.
On-screen
display
Items
Use
Use this setting for regular recording
conditions. The camcorder automatically
adjusts the aperture value and shutter
speed for optimum recording.
Auto
-
Select the recording (
) mode by pressing the [MODE]
button. page 26
For recording rapidly moving subjects.
Example: When recording sports.
For recording a portrait image. Use this
setting to capture natural skin tones.
For recording subjects under strong light.
For example, under stage spotlights in
theaters.
Use where sunlight or the reflection of light
is intense. Example: a beach or snow field.
Sports
Press the [MENU] button
[Control (Left/Right)] button
iSCENE.
1
2
STBY
[220Min]
Portrait
iSCENE
Auto
Spotlight
Sports
Portrait
Select the desired submenu item
with the [Control (Up/Down)]
button, and then press the
[Control (OK)] button.
Exit
Beach & Snow
For recording objects close-up in high
color saturation.
Food
Press the [MENU] button to exit the menu.
Waterfall
For recording a waterfall or fountain.
3
You can also set iSCENE with the shortcut menu. page 27
52
Advanced recording
•
•
•
60p indicates the camcorder will record in progressive scan mode at
60 frames per second.
30p indicates the camcorder will record in progressive scan mode at
30 frames per second.
Recorded files are encoded using Variable Bit Rate (VBR). VBR is an
encoding system that automatically adjusts the bit rate according to
the image being recorded.
Video Resolution
You can select the resolution of a video to be recorded.
Select the recording (
button. page 26
) mode by pressing the [MODE]
•
•
High resolution images occupy more memory space than low
resolution images. If you select the higher resolution, there is less
space to record videos in the memory.
The recording times depend on the resolution of a video to be
recorded. page 33
Press the [MENU] button
[Control (Left/Right)] button
Video Resolution.
STBY
[220Min]
1
2
Video Resolution
1280X720/30p
720X480/60p(16:9)
720X480/60p(4:3)
Select the desired submenu item
with the [Control (Up/Down)]
button, and then press the
[Control (OK)] button.
Exit
Press the [MENU] button to exit the menu.
3
Submenu Items
On-screen
display
Items
Use
1280x720/30p
Records in 1280x720 (30p) resolution.
720x480/60p
(16:9)
Records in 720x480 (60p) resolution
with 16:9 aspect ratio.
Records in 720x480 (60p) resolution
with 4:3 aspect ratio.
720x480/60p(4:3)
53
Advanced recording
Photo Resolution
White Balance
You can select the quality of photo images to be recorded.
Using the White Balance function, you can select a setting that
matches the light illuminating the subject you are shooting (Daylight,
Fluorescent, etc.) or let the camcorder make all adjustments
automatically. Based on your selection, the camcorder automatically
adjusts the color of the subject so the colors in your recording look
natural.
Select the recording (
) mode by pressing the [MODE]
button. page 26
Press the [MENU] button
[Control (Left/Right)] button
Photo Resolution.
1
2
STBY
[220Min]
Photo Resolution
1696X954(16:9)
1280X720(16:9)
Select the recording (
) mode by pressing the [MODE]
button. page 26
Select the desired submenu item
with the [Control (Up/Down)]
button, and then press the
[Control (OK)] button.
STBY
[220Min]
Press the [MENU] button
[Control (Left/Right)] button
White Balance.
1
2
Exit
White Balance
Auto
Daylight
Cloudy
Press the [MENU] button to exit the menu.
3
Select the desired submenu item
with the [Control (Up/Down)]
button, and then press the
[Control (OK)] button.
Exit
Submenu Items
On-screen
display
Items
Use
Press the [MENU] button to exit the menu.
3
1696x954(16:9)
1280x720(16:9)
1600x1200(4:3)
800x600(4:3)
Record in 1696x954 resolution.
Record in 1280x720 resolution.
Record in 1600x1200 resolution.
Record in 800x600 resolution.
Understanding White Balance
The White Balance (WB) process removes unrealistic color casts
so that white objects are rendered white in your image and all other
colors look natural. Proper white balance has to take into account
the ‘color temperature’ of a light source, which refers to the relative
warmth or coolness of white light.
•
Other devices may not display photos recorded by your camcorder if those
devices do not support high resolution.
•
•
For photo development, the higher the resolution, the finer the image quality.
The number of recordable images differs according to the photo resolution you
select. page 33
High resolution images occupy more memory space than low resolution images.
If you select a higher resolution for your photos, you will have less space to store
photos in the memory.
•
•
Resolutions marked with are the resolutions of photos your record when you set
video resolution to 720X480/60p (4:3).
54
Advanced recording
To set the white balance manually
Submenu items
Select Custom WB.
STBY
[220Min]
9999
1
2
On-screen
display
Items
Use
•
The indicator (
) and message
Set White Balance
Set White Balance appear.
To let the camcorder adjust the white
balance automatically according to
the lighting conditions.
Auto
-
Frame a white object such as
a piece of paper so it fills the
screen. Use an object that is not
transparent.
Exit
OK
For recording in clear, outdoor
lighting.
Daylight
Cloudy
White thick paper
•
If the object filling the screen is
not focused, correct the focus
using Focus: Manual.
page 58
For recording in the shade or cloudy
weather.
For recording under white fluorescent
lights.
Fluorescent
Tungsten
Press the [Control (OK)] button.
3
4
For recording under halogen lamps
and incandescent lights.
•
The camcorder applies the
stored white balance the next time you record.
Lets you manually adjust the white
balance to match the light source or
situation.
Press the [MENU] button to exit the menu.
Custom WB
•
A subject can be recorded under various types of lighting conditions
indoors (natural, fluorescent, candlelight, etc.). Because the color
temperature is different depending on the light source, the subject's
tint will differ, affecting the subject's white balance. Use this function
to correct the white balance and provide a more natural result.
•
When you set white balance manually, the object you frame must
be white. Otherwise your camcorder may not detect an appropriate
setting value.
•
•
The adjusted setting remains until you set the white balance again.
During normal outdoor recording, setting to Auto may provide better
results.
•
•
Cancel the digital zoom function for a clear and precise setting.
Reset the white balance if light conditions change.
55
Advanced recording
Face Detection
Examples of the Face detection mode
When you set Face detection to On, the face detection frame
appears around faces as shown in the figure below.
The camcorder can detect up to three faces.
Face Detection detects and recognizes face-like shapes and adjusts
focus, color, and exposure automatically. Also, it adjusts recording
conditions so that they are optimized for the face detected.
STBY
[220Min]
9999
Select the recording (
button. page 26
) mode by pressing the [MODE]
Press the [MENU] button
[Control (Left/Right)] button
Face Detection.
STBY
[220Min]
1
2
Face Detection
Off
On
•
•
The Face Detection indicator ( ) and Face Detection frame (
are not recorded.
Face Detection may not operate depending on the recording
conditions. For example, the Face Detection frame may appear on a
'face-like' shape, even when the subject is not a person's face. If this
occurs, turn off the Face Detection function.
)
Select the desired submenu item
with the [Control (Up/Down)]
button, and then press the
[Control (OK)] button.
Exit
•
•
The Face Detection frame will not work on the side of a person's
face or if the illumination is too low. You must be facing subjects
‘head-on’ and have enough illumination.
To exit the menu, press the [MENU] button.
3
You can also set Face Detection with the shortcut menu. page 27
Submenu Items
On-screen
display
Items
Off
Use
To disable the function.
-
To detect faces automatically and set the optimal
recording values.
On
56
Advanced recording
EV (Exposure Value)
Understanding EV (Exposure Value)
The camcorder usually adjusts the exposure automatically.
You can also manually adjust the exposure to your preference.
Exposure value is the total amount of light allowed to fall on the
photographic media (Image sensor) during the process of taking
photos or videos. The higher the number, the greater the exposure.
For example, + 0.3 lets in more light than -0.3.
Select the recording (
) mode by pressing the [MODE]
button. page 26
STBY
[220Min]
Press the [MENU] button
[Control (Left/Right)] button
EV.
1
EV
Adjust
Press the [Control (OK)] button.
Darker (-)
Brighter (+)
2
3
Exit
0.0
Press the [Control (Left/Right)]
button to adjust the exposure while
viewing the image on the LCD
screen.
STBY
[220Min]
9999
You can also set EV with the shortcut menu. page 27
EV
0.0
•
EV values ( ): -2.0, -1.6, -1.3,
-1.0, -0.6, -0.3, 0, +0.3, +0.6,
+1.0, +1.3, +1.6, +2.0
Confirm your selection by pressing the [Control (OK)] button.
4
•
The camcorder applies the exposure value setting and the
indicator ( ) and setting value appear.
To cancel the adjusted exposure value manually, select 0 in
Step 3.
•
57
Advanced recording
C.Nite
Focus
You can adjust the shutter speed when recording a slow moving
object or a brighter image in dark places without compromising
colors.
When you turn the camcorder on, focus is always set to automatic.
You can also set the focus manually.
Select the recording (
button. page 26
) mode by pressing the [MODE]
Select the recording (
button. page 26
) mode by pressing the [MODE]
Press the [MENU] button
[Control (Left/Right)] button
Focus.
1
2
STBY
[220Min]
Press the [MENU] button
[Control (Left/Right)] button
C.Nite.
STBY
[220Min]
1
2
Focus
C.Nite
Auto
Off
On
Manual
Select the desired submenu item
with the [Control (Up/Down)]
button, and then press the
[Control (OK)] button.
Select the desired submenu item
with the [Control (Up/Down)]
button, and then press the
[Control (OK)] button.
Exit
Exit
Press the [MENU] button to exit the menu.
3
Press the [MENU] button to exit the menu.
3
Submenu Items
Submenu Items
On-screen
display
On-screen
display
Items
Off
Use
To disable the function.
Items
Auto
Use
In most situations, it is better to use the automatic
focus feature, as it enables you to concentrate on
the creative side of your recording.
-
-
To record a brighter image by extending the
low shutter speed range to 1/60 or 1/30.
On
To focus manually. Manual focusing may be
necessary under certain conditions that make
automatic focusing difficult or unreliable.
Manual
•
•
When you use C.Nite, the image takes on a slow motion like effect.
In addition, the focus adjusts slowly and white dots may appear on
the screen. This is not a defect.
When Video Resolution is set to 1280x720/30p, the C.Nite function
does not operate.
58
Advanced recording
Adjusting the focus manually
Examples of when to use the Manual focus mode
This camcorder automatically focuses subjects from close-up to
infinity. However, the correct focus may not be obtained depending
on the recording conditions. If this occurs, use the manual focus
mode.
•
•
•
When the subject is dark.
When the background is too bright.
When you view the subject through a window that is stained or
wet.
When the subject has dense horizontal or sloping stripes.
When the subject is distant and behind a nearby wire fence.
When you are shooting walls, the sky, or other low-contrast
subjects.
•
•
•
Press the [Control (Up/Down)]
1
STBY
[220Min]
9999
button to select Manual.
•
•
•
When the subject is emitting or reflecting strong light.
When you are focusing on a subject near the boundary of the
frame.
The manual focus adjustment
indicator appears.
Manual
Press the [Control (Left/Right)]
button to select the desired
2
•
•
You can also adjust the focus with the shortcut menu. page 27
Manual focusing focuses on a point in the framed scene while auto
focusing focuses on the center area automatically.
The Auto Focus (AF) setting is useful when you operate the zoom
function because you might not be able to keep accurate focus after
the zoom ratio has been changed.
When Zoom Type is set to Digital Zoom, manual focusing will not
focus accurately. Before focusing manually, check if the Digital
Zoom is turned off. page 62
indicator to adjust focus, and then press the [Control (OK)]
button.
•
The camcorder applies the manual focus setting and the (
indicator appears.
)
•
•
Focusing on a nearer or farther subject
To focus on a nearer subject, press the [Control (Left)] button.
To focus on a further subject, press the [Control (Right)] button.
•
The nearer or further icon (
/
) appears between the
indicators when focus adjustment reaches the end.
The adjusted value is applied right after you press the [Control
(Left/Right)] button to adjust the focus.
•
<Nearer subject>
<Further subject>
59
Advanced recording
Anti-Shake(HDIS)
Use the Anti-Shake function in the following cases
Use the Anti-Shake(HDIS) function to compensate for unstable
images caused by shaking movements while holding the camcorder.
•
•
•
When recording while using the zoom extensively.
When recording a close up picture of a small object.
When recording while walking, or in a moving car.
Select the recording (
button. page 26
) mode by pressing the [MODE]
Press the [MENU] button
[Control (Left/Right)] button
Anti-Shake(HDIS).
1
2
STBY
[220Min]
Anti-Shake(HDIS)
Off
On
Select the desired submenu item
with the [Control (Up/Down)]
button, and then press the
[Control (OK)] button.
•
•
•
•
The camcorder automatically activates the Anti-Shake(HDIS)
function in the Smart Auto mode.
Gross camcorder shake may not be entirely corrected even if Anti-
Shake(HDIS) is On. Hold the camcorder firmly with both hands.
When this function is On, the actual movement of the subject and
the movement displayed on the screen may be slightly different.
When recording in dark lighting at high magnification while this
function is On, after-images may stand out. If this occurs, we
recommend using a tripod (not supplied) and turning Anti-
Shake(HDIS) to Off.
Exit
Press the [MENU] button to exit the menu.
3
Submenu Items
On-screen
display
Items
Off
Use
To disable the function.
-
To enable the Anti-Shake(HDIS) function to
compensate for shaking movements.
On
60
Advanced recording
Digital Special Effect
Examples of 7 digital effect options
Using the digital special effect function gives your recording a
creative look.
Off
Disables the function.
Select the recording (
button. page 26
) mode by pressing the [MODE]
Blk&Wht (
)
This mode changes the image into black and
white.
Press the [MENU] button
[Control (Left/Right)] button
Digital Special Effect.
1
2
STBY
[220Min]
Sepia (
)
Digital Special Effect
This mode gives images a reddish brown cast.
Off
Blk&Wht
Sepia
Select the desired submenu item
with the [Control (Up/Down)]
button, and then press the
[Control (OK)] button.
Negative (
)
Exit
This mode reverses the colors and the brightness
and creates a negative effect.
Dazzle (
)
This mode creates a brighter image by increasing
color saturation.
Press the [MENU] button to exit the menu.
3
Noir (
)
This mode creates a stronger image by
increasing contrast.
Western (
)
This mode creates a faded and old film vintage
look.
61
Advanced recording
Zoom Type
Digital zoom range
The camcorder offers three types of zoom: optical, intelligent, and
digital zoom.
STBY
[220Min]
9999
Select the recording (
button. page 26
) mode by pressing the [MODE]
Press the [MENU] button
[Control (Left/Right)] button
Zoom Type.
1
2
STBY
[220Min]
The right side of the bar shows the digital zooming zone. The zooming
zone appears when you move the [Zoom] lever or [Zoom] button.
Zoom Type
Optical Zoom
Intelli Zoom
Digital Zoom
Select the desired submenu item
with the [Control (Up/Down)]
button, and then press the
[Control (OK)] button.
•
•
With digital zoom, the image is digitally processed more than it is in
the intelli or optical zoom modes. As a result, the image resolution
may deteriorate. The image quality may deteriorate depending on
how much you zoom in on the subject.
The zoom range will change depending on the aspect ratio of the
video.
Exit
Press the [MENU] button to exit the menu.
3
Submenu Items
Items
Use
Optical Zoom
To use optical zoom, up to 52X.
•
The camcorder zooms the full width of the
image sensor to obtain a larger zoom range
without any deterioration in image quality.
Intelli-zoom is available up to 70X.
When this option is selected, the camcorder will
automatically switch to the digital zoom if you
zoom in beyond the optical or intelligent zoom
range.
Intelli Zoom
Digital Zoom
•
•
•
Digital zoom is available up to 130X.
62
Advanced recording
Cont. Shot
Submenu Items
The Continuous Shot function allows you to capture photos in rapid
succession and gives you more photo-taking opportunities when
recording moving subjects.
On-screen
display
Items
Use
Off
On
To record only one photo image.
-
While you are pressing the [PHOTO] button,
the camcorder can take up to 30 photos
continuously.
Select the recording (
) mode by pressing the [MODE]
button. page 26
Press the [MENU] button
[Control (Left/Right)] button
Cont. Shot.
1
2
STBY
[220Min]
•
•
The number of recordable photos depends on the photo’s resolution
and the memory space available.
If an error occurs (Card full, etc.) during continuous shot, the
recording stops and an error message appears.
Cont. Shot
Off
On
Select the desired submenu item
with the [Control (Up/Down)]
button, and then press the
[Control (OK)] button.
Exit
Press the [MENU] button to exit the menu.
3
63
Advanced recording
Move to the next setting (Hr) by pressing the [Control (Left/
Right)] button, and then set the desired total recording time in
the same way.
4
Time Lapse REC
Using the Time Lapse feature, you can program your camcorder to
create a time lapse video by recording a series of frames over a set
period of time with a set time interval between each frame. The Time
Lapse feature lets you create time lapse videos of blooming flowers
and similar subjects.
Press the [Control (OK)] button to finish the setting, and then
press the [MENU] button to exit the menu.
5
6
After setting the Time Lapse REC mode, press the [Recording
start/stop] button.
•
•
Select the recording (
) mode by pressing the [MODE]
button. page 26
•
The Time Lapse REC starts.
To record in the Time Lapse REC mode, you must set the
recording interval between frames (Interval) using the menu.
Submenu items
Press the [MENU] button
[Control (Left/Right)] button
Time Lapse REC.
1
2
STBY
[220Min]
On-screen
display
Items
Use
Time Lapse REC
Off
On
Off
To disable the function.
-
: 1 Sec
24 Hr
•
Interval (Sec): To set the time interval between
image captures.
1 3 5 10 15 30 (Seconds)
REC Limit (Hr): To set the total time of
recording.
Press the [Control (Up/Down)]
button to select On, then press the
[Control (OK)] button.
Exit
On
•
STBY
[220Min]
•
The recording interval and total
24 48 72 (Hours)
∞
recording time items appear.
Time Lapse REC
Off
On
1
24
Hr
Sec /
Set the desired recording interval
(Sec) with [Control (Up/Down)]
button.
3
= 48 Min
OK
During Time Lapse recording, the C.Nite function does not work.
Exit
Move
64
Advanced recording
Example of Time Lapse Recording
The Time Lapse Recording function records image frames at
a predefined interval over the total recording time to produce a
time-lapse video.
Total time for recording
Recording interval
Time Lapse Recording is useful for filming the following subjects:
Timeline
-
-
-
Blooming flowers
A bird building a nest
Clouds rolling by in the sky
Time for recording on the
storage media (a video of the
Time Lapse Recording)
0:00:00/0:00:55
0:00:10/0:00:55
0:00:20/0:00:55
0:00:30/0:00:55
100-0001
100-0001
100-0001
100-0001
•
•
Time Lapse Recording mode is released once recording has been finished. To start another Time Lapse Recording, repeat steps 1 to 6 on the previous page.
Depending on the video resolution, 60 or 30 captured images compose a video of 1 second length. Since the minimum length of a video that your camcorder can save
is one second, the interval defines the total minimum recording time for the Time Lapse Recording. For example, if you set the interval to 30 Sec, you need to set the
recording time to at least 30 minutes for a 60 frames per second resolution or 15 minutes for a 30 frames per second resolution to record a video 1 second long.
Press the [Recording start/stop] button if you want to stop the Time Lapse Recording.
•
•
•
Audio is not recorded during time lapse recording.
The maximum continuous recording time is under 20 minutes. The maximum video file size is 1.8GB. When a video recording time is more than 20 minutes or a video
file exceeds 1.8GB, a new video file is created automatically.
•
•
If the battery charge is exhausted during time lapse recording, the camcorder saves recording up to that point and switches to standby mode. After a while, it displays a
warning message, then turns off automatically.
If the storage media becomes full during time lapse recording, the camcorder switches to the standby mode after saving the recording up to the maximum memory
available.
We recommend using the power adaptor for a Time Lapse Recording instead of the battery.
When a time lapse recording starts, the Time Lapse Recording message will blink even if you switch the information display mode to the minimum display mode.
This is normal operation. Do not remove the power source or memory card from the camcorder.
•
•
65
Advanced recording
Guideline
Submenu Items
This camcorder provides 3 types of guidelines to help you to set up
a balanced image composition on the screen.
On-screen
display
Items
Use
To cancel the guideline function.
Off
-
Select the recording (
) mode by pressing the [MODE]
Cross
Use when focusing a subject in the center.
button. page 26
Use when recording a subject in a
horizontal or vertical composition or
shooting with the tele macro function.
Positioning subjects within the Safety
Zone rectangle ensures they will be
recorded.
Grid
Press the [MENU] button
[Control (Left/Right)] button
Guideline.
1
2
STBY
[220Min]
Guideline
Off
Safety Zone
Cross
Grid
Select the desired submenu item
with the [Control (Up/Down)]
button, and then press the
[Control (OK)] button.
Exit
•
•
Positioning a subject at the cross point of a guideline provides a
balanced composition.
Guidelines are not recorded.
Press the [MENU] button to exit the menu.
3
66
Advanced playback
Thumbnail View Option
Normal
Date
The Thumbnail View Option lets you sort thumbnails of the recorded
videos or photos by different display options.
Normal
0:00:55
Date
1/10
JAN/01/2013
1/10
•
•
Press the [MODE] button to select the playback (
page 26
Select the video or photo thumbnail view. page 42
) mode.
0:10:31
Date
Photo
Move
Play
Photo
Play
Press the [MENU] button
[Control (Left/Right)] button
Thumbnail View Option.
1
2
Normal
This function is available in thumbnail view only.
Thumbnail View Option
Normal
Date
Select the desired submenu item
with the [Control (Up/Down)]
button, and then press the
[Control (OK)] button.
Exit
Submenu Items
Items
Use
To display the file thumbnails in the order in which the
files were recorded.
To sort the file thumbnails by the date the files were
recorded.
Normal
Date
67
Advanced playback
PlayOption
Smart BGM Option
You can play back one video or all videos once, or play back one
video or all videos repeatedly.
You can play back a video with background music. The Smart BGM
Option lets you select the music that will play.
•
•
Press the [MODE] button to select the playback (
page 26
This function is available in the video single view only.
) mode.
•
•
Press the [MODE] button to select the playback (
page 26
Select the video thumbnail view. page 42
) mode.
Press [MENU] button [Control
(Left/Right)] button
Smart BGM Option.
1
2
0:00:01/ 0:00:06
Press the [MENU] button
[Control (Left/Right)] button
PlayOption.
1
2
Normal
Smart BGM Option
PlayOption
Play All
The Flea Waltz
Canon in D
Select the desired submenu item
with the [Control (Up/Down)]
button, and then press the
[Control (OK)] button.
Play One
Repeat All
Cello Suite No.1
A
Select the desired submenu item
with the [Control (Up/Down)]
button, and then press the
[Control (OK)] button.
Exit
Exit
Press the [MENU] button to exit the menu.
3
•
To play back the selected background music with a video,
press the [SMART BGM] button when the video plays back.
To stop the background music, press the [SMART BGM]
button again.
Press the [MENU] button to exit the menu.
3
Submenu Items
Submenu Items
On-screen
display
Items
Use
Items
Use
To play back The Flea Waltz.
To play back Canon in D.
To play back Cello Suite No.1.
To play back Nocturne.
To play back from the selected video to the
last video.
Play All
Play One
Repeat All
The Flea Waltz
Canon in D
Cello Suite No.1
Nocturne
To play back the selected video only once.
A
To play back all videos repeatedly.
Repeat One
To play back the selected video repeatedly.
To play back from The Flea Waltz to Nocturne
randomly.
Random
When you change background music by pressing the [MENU] button while
the video is playing back, the video will be paused. Press the [Control
(OK)] button to play back the paused video again with the changed
background music.
68
Advanced playback
The song saved into the memory
card appears on the Smart BGM
Option menu in video playback
mode. page 68
Using external songs as background music (Smart BGM II)
You can play songs you have saved to a memory card as
background music as well as the songs stored in the camcorder’s
memory and available through the Smart BMG option.
6
0:00:01/ 0:00:06
Smart BGM Option
Nocturne
NewBGM1
Random
Exit
•
•
Insert a memory card.
Prepare external songs for background music.
To delete the external songs in the memory card
To set external songs as background music
You can delete the external songs from
Manage BGM in the Smart BGM screen
or from the BGM folder in the memory
card.
Convert your songs to a compatible format using the built-in Intelli-
studio program so they can be recognized by the camcorder.
Connect the camcorder to a PC with the USB cable to run the
1
Intelli-studio program. page 86
Click Tool on the Intelli-studio
screen Sending song for
2
Smart BGM.
•
•
The camcorder can only recognize the external songs converted by
the Intelli-studio program.
Intelli-studio can only convert files saved in the mp3 and m4a
formats.
External songs are saved into the BGM folder in the memory card.
If you transfer the converted m4a files into the BGM folder in the
memory card, you can use them with Smart BGM.
Click Browse on the Smart BGM
screen, and then select the desired
song.
3
•
•
Change the song’s name so it can
be recognized by the camcorder,
4
and then click Send Yes.
•
The song is converted to
the m4a format, and then
transferred into the memory
card in the camcorder.
When the transfer finishes, click
OK.
5
69
•
You can save up to 5 converted songs in the memory card in the
camcorder
.
Advanced playback
If you selected All Files, the message corresponding to the
selected option appears. Use the [Control (Left/Right)] button
to select Yes, and then press the [Control (OK)] button.
4
Delete
You can erase your recordings one by one or all at once.
•
•
Press the [MODE] button to select the playback (
page 26
Select the video or photo thumbnail view. page 42
) mode.
Submenu Items
Items
Use
Select Files
To delete selected videos or photos.
Press the [MENU] button
[Control (Left/Right)] button
Delete.
Normal
1
2
3
To delete all videos or photos, except for the
protected files.
Delete
All Files
Select Files
All Files
Select an option by pressing the
[Control (Up/Down)] button, and
then press the [Control (OK)] button.
•
•
Deleted images cannot be recovered.
Do not remove the power adaptor or memory card while deleting
files, otherwise the storage media may be damaged.
Exit
If you selected Select Files, image
thumbnails appear.
Delete
•
•
You can also delete your recordings in single view.
To protect important images from accidental deletion, activate image
protection. page 72
0:00:55
1/10
ⓐ
Use the [Control (Up/Down/
Left/Right)] button to move to
the photo or video you want to
delete.
•
•
•
Protected images cannot be deleted. To delete a protected image,
cancel the protect function first. page 72
If the write protection tab on a memory card is set to lock, you
cannot delete.
You can also format the storage media to delete all the images at
once. Be aware that all files and data including protected files will be
erased. page 80
Delete
Move
Cancel
ⓑ
Press the [Control (OK)] button
(
)
to mark images for deletion. The garbage can icon
appears on the photo or video.
Repeat Steps ⓐ and ⓑ for each photo or video you want to
delete.
Press the [MENU] button to delete the photos and videos you
selected.
The message corresponding to the selected option appears.
Use the [Control (Left/Right)] button to select Yes, and then
press the [Control (OK)] button.
ⓒ
ⓓ
ⓔ
•
The Delete function does not operate if the battery charge is
insufficient. We recommend you use the power adaptor to avoid
power-loss while deleting.
70
Advanced playback
If you selected All Files, the message corresponding to the
selected option appears. Use the [Control (Left/Right)] button
to select Yes, and then press the [Control (OK)] button.
4
Delete My Clip
You can delete the My Clip tag from a video tagged as ‘My Clip’.
•
•
Press the [MODE] button to select the playback (
page 26
Select the video thumbnail view. page 42
) mode.
Submenu Items
Items
Use
Select Files
To delete the My Clip tags from selected videos.
Press the [MENU] button
[Control (Left/Right)] button
Delete My Clip.
Normal
1
2
3
All Files
To delete the My Clip tags from all videos.
Delete My Clip
Select Files
All Files
Select an option by pressing the
[Control (Up/Down)] button, and
then press the [Control (OK)] button.
Deleted My Clip tags cannot be recovered.
Exit
You can also delete the My Clip tags from videos in single view.
If you selected Select Files, image
thumbnails appear.
Delete My Clip
0:00:55
1/10
ⓐ
Use the [Control (Up/Down/
Left/Right)] button to move to a
(
)
.
video tagged as My Clip
Press the [Control (OK)] button.
The garbage can icon
appears on the video.
Delete
Move
Cancel
ⓑ
(
)
ⓒ
ⓓ
ⓔ
Repeat Steps ⓐ and ⓑ for each video tagged as My Clip
(
)
.
Press the [MENU] button to delete all tags from the videos
you selected.
The message corresponding to the selected option appears.
Use the [Control (Left/Right)] button to select Yes, and then
press the [Control (OK)] button.
71
Advanced playback
If you selected All On, the message corresponding to the
selected option appears. Use the [Control (Left/Right)] button
to select Yes, and then press the [Control (OK)] button.
4
5
Protect
You can protect important saved videos or photos from accidental
deletion. You cannot delete protected images unless you release the
protection or format the memory.
If you selected All Off, the message corresponding to the
selected option appears. Use the [Control (Left/Right)] button
to select Yes, and then press the [Control (OK)] button.
•
•
Press the [MODE] button to select the playback (
page 26
Select the video or photo thumbnail view. page 42
) mode.
Submenu Items
Press the [MENU] button
[Control (Left/Right)] button
Protect.
Normal
1
2
Items
Use
Protect
Select Files
To protect selected videos or photos from deletion.
Select Files
All On
All On
All Off
To protect all videos or photos.
All Off
Select an option by pressing the
[Control (Up/Down)] button, and
then press the [Control (OK)]
button.
Exit
To cancel the protection for all videos or photos.
Protect
0:00:55
If you selected Select Files, image
thumbnails appear.
3
•
•
You can also protect you recordings in single view.
If the write protection tab on a memory card is set to lock, you
cannot set image protection. page 31
1/10
ⓐ
Use the [Control (Up/Down/
Left/Right)] button to move to
the photo or video you want to
protect.
Protect
Move
Cancel
ⓑ
Press the [Control (OK)] button
(
)
to mark images for protection. The key icon
on the photo or video.
appears
ⓒ
ⓓ
ⓔ
Repeat Steps ⓐ and ⓑ for each photo or video you want to
protect.
Press the [MENU] button to protect the photos and videos
you selected.
The message corresponding to the selected option appears.
Use the [Control (Left/Right)] button to select Yes, and then
press the [Control (OK)] button.
72
Advanced playback
If you selected All On, the message corresponding to the
selected option appears. Use the [Control (Left/Right)] button
to select Yes, and then press the [Control (OK)] button.
4
5
Share Mark
You can set the share mark on a video and directly upload the
marked file to the YouTube site.
If you selected All Off, the message corresponding to the
selected option appears. Use the [Control (Left/Right)] button
to select Yes, and then press the [Control (OK)] button.
•
•
Press the [MODE] button to select the playback (
page 26
Select the video thumbnail view. page 42
) mode.
Submenu Items
Press the [MENU] button
[Control (Left/Right)] button
Share Mark.
1
2
Normal
Items
Use
Share Mark
Select Files
All On
Select Files
To set the share mark selected videos.
All On
All Off
To set the share mark all videos.
Select an option by pressing the
[Control (Up/Down)] button, and
then press the [Control (OK)]
button.
All Off
Exit
To remove the share mark from all marked videos
all at once.
•
•
•
You can also set the share mark on your videos in the single image
display mode.
By using the Intelli-studio software embedded in the camcorder, you
can easily upload videos marked with share marks. page 90
When uploading a video file to a web site such as YouTube, the one-
time upload maximum is 14 minutes 59 seconds.
If you selected Select Files, image
thumbnails appear.
3
Share Mark
0:00:55
1/10
ⓐ
Use the [Control (Up/Down/
Left/Right)] button to move
to the video you want to share
mark.
Mark
Move
Cancel
ⓑ
Using the Share ( ) button
Press the [Control (OK)] button
to select each video you want to share mark. The share mark
You can set the share mark on a video by simply pressing
the [Share ( )] button.
(
)
icon
appears on the video.
ⓒ
ⓓ
ⓔ
Repeat Steps ⓐ and ⓑ for each video you want to share
mark.
Press the [MENU] button to mark the videos you want to
share.
The message corresponding to the selected option appears.
Use the [Control (Left/Right)] button to select Yes, and then
press the [Control (OK)] button.
73
Advanced playback
Slide Show
File Info
You can enjoy a slide show with various effects.
You can see the image information for photos and videos.
•
•
Press the [MODE] button to select the playback (
page 26
Select the photo thumbnail view. page 42
) mode.
Press the [MODE] button to select the playback (
page 26
) mode.
Normal
Press the [MENU] button
[Control (Left/Right)] button
File Info [Control (OK)] button.
1
2
Press the [MENU] button
[Control (Left/Right)] button
Slide Show.
Normal
1
2
File Info
Select Files
Slide Show
Start
•
The file selection screen
appears.
:
:
1Sec
On
Interval
Music
Select an option by pressing the
[Control (Up/Down)] button, and
then press the [Control (OK)]
button.
Exit
Exit
Select the desired video or photo
by pressing the [Control (Up/
Down/Left/Right)] button, and
then press the [Control (OK)]
button.
File Info
1/10
100VIDEO
HDV_0001.MP4
JAN/01/2013
0:00:20
Date
:
:
:
:
Press the [MENU] button to exit
the menu.
Duration
Size
3
22.6 MB
Resolution
1280X720/30p
•
The following information for the
selected file appears:
Exit
OK
100-0001
-
-
-
-
Date
Submenu Items
Duration (Video only)
Size
Resolution
Items
Use
To start a slide show from the current image.
-
-
The indicator ( ) appears.
To stop the slide show, press the [Control (OK)] button
again.
Press the [MENU] button to exit the menu.
3
Start
-
To return to the thumbnail view, move the [Zoom] lever.
Continuously plays back photos at the interval you select.
You can choose 1sec or 3sec.
You can turn the internal background music on or off. This
camcorder has 4 default background melodies stored in the
boot-up flash memory. If the music is on when the slide show
starts, the 4 melodies will play back in shuffle mode.
Interval
Music
74
Other settings
Storage Info
File No.
Storage Info displays the storage information for the storage media.
The camcorder assigns file numbers to recorded files in the order
they were recorded. Use File No. to continue or reset the current file
number sequence.
Press the [MENU] button
[Control (Left/Right)] button
Settings [Control (Up/
Down)] button Storage Info
[Control (OK)] button.
1
Storage Info
STBY
[220Min]
Storage
Used
:
:
:
Card
1
Press the [MENU] button
[Control (Left/Right)] button
Settings [Control (Up/
Down)] button File No.
[Control (OK)] button.
190MB
14.6GB
Settings
Free
Storage Info
File No.
:
Exit
Move
Back
•
Press the [Control (Up/Down)]
button to move the screen up
or down and view additional
information.
Date/Time Set
Exit
STBY
[220Min]
2
3
Select the desired submenu item
with the [Control (Up/Down)]
button, and then press the
[Control (OK)] button.
•
You can check the used
Settings
memory, available memory, and
the available recordable time for
each recording resolution.
Storage Info
File No.
Series
Reset
Date/Time Set
Exit
To exit the menu, press the
[MENU] button.
Press the [MENU] button to exit the menu.
2
Submenu Items
•
•
If there is no storage media inserted, it cannot be selected and will
be dimmed on the menu.
The actual capacity may be less than the capacity displayed on the
LCD screen as the camcorder’s system files occupy a part of the
capacity.
Items
Use
Assigns file numbers in sequence even if you have inserted a
different memory card, formatted the card, or deleted all files.
The file number is reset only when a new folder is created.
Series
Reset
Resets the file number to 0001.
When you set File No. to Series, each file is assigned a different number
to avoid duplicating file names. It is convenient when you want to manage
your files on a computer.
75
Other settings
Date/Time Set
Date/Time Display
You can set whether or not the date and/or time appear on the LCD
screen.
By setting the date and time, you can display the date and time of a
recording during playback.
STBY
[220Min]
Press the [MENU] button
1
1
Press the [MENU] button
[Control (Left/Right)] button
Settings [Control (Up/Down)]
button Date/Time Display
[Control (OK)] button.
STBY
[220Min]
[Control (Left/Right)] button
Settings [Control (Up/Down)]
button Date/Time Set
[Control (OK)] button.
Settings
Settings
Date/Time Set
Date/Time Display
LCD Brightness
Date/Time Set
Date/Time Display
LCD Brightness
:
:
12
OFF
:
12
OFF
:
Exit
Exit
Select the date or time information,
and change the setting values by
pressing the [Control (Up/Down/
Left/Right)] button.
2
3
2
3
Select the desired submenu and
menu item with the [Control (Up/
Down)] button, and then press
[Control (OK)] button.
STBY
[220Min]
Date/Time Set
Settings
Month Day
JAN
01
Year
2013
Hr Min
Off
12
OFF
Date/Time Set
Date/Time Display
LCD Brightness
Date
Time
12
00 AM
Press the [MENU] button to exit
the menu.
Make sure the clock is correctly set,
and then press the [Control (OK)]
button.
Exit
Cancel
Move
OK
•
The date/time appears on the
LCD screen according to the selected option.
Submenu Items
The year can be set up to 2037.
Items
Use
On-screen display
To not display the current date/
time.
Off
-
JAN/01/2013
12:00AM
Date
Time
To display the current date.
To display the current time.
JAN/01/2013
12:00AM
To display the current date and
time.
Date & Time
When the internal battery is depleted, the date/time will read
JAN/01/2013 12:00AM.
76
Other settings
LCD Brightness
Auto LCD Off
To reduce power consumption, the brightness of the LCD screen
is automatically dimmed if the camcorder is idle for more than 2
minutes.
You can adjust the brightness of the LCD screen to compensate for
ambient lighting conditions.
STBY
[220Min]
Press the [MENU] button
[Control (Left/Right)] button
Settings [Control (Up/Down)]
button LCD Brightness
[Control (OK)] button.
1
1
Press the [MENU] button
[Control (Left/Right)] button
Settings [Control (Up/
Down)] button Auto LCD Off
[Control (OK)] button.
STBY
[220Min]
Settings
Date/Time Set
Date/Time Display
LCD Brightness
Settings
:
:
12
OFF
LCD
:
Auto LCD Off
Beep Sound
Shutter Sound
:
:
Exit
Select the desired submenu and
menu item with the [Control (Up/
Down)] button, and then press
[Control (OK)] button.
2
3
Exit
STBY
[220Min]
2
3
Select the desired submenu item
with the [Control (Up/Down)]
button, and then press the
[Control (OK)] button.
STBY
[220Min]
Settings
Date/Time Set
Date/Time Display
LCD Brightness
Normal
Bright
Settings
Auto LCD Off
Beep Sound
Shutter Sound
LCD
Off
On
Press the [MENU] button to exit
the menu.
LCD
Exit
Press the [MENU] button to exit
the menu.
Exit
Submenu Items
Submenu Items
Items
Use
Items
Off
Use
Normal
Bright
Standard brightness.
Brightens the LCD screen.
To disable the function.
When the camcorder is idle for more than 2 minutes in the STBY
mode, or for more than 5 minutes when recording a video, the
power saving mode starts and dims the LCD screen.
On
•
If the surrounding is too bright, adjust the brightness of the LCD
screen.
•
•
Adjusting the LCD screen does not affect the image being recorded.
A brighter LCD screen consumes more power.
•
•
When the Auto LCD Off function is enabled, you can press any
button on the camcorder to return LCD brightness to normal.
Auto LCD Off will be disabled in the following situation:
- If the power cable (Power adaptor, USB cable) is connected.
77
Other settings
Beep Sound
Shutter Sound
You can turn the shutter sound the camcorder emits when you
press the [PHOTO] button on or off.
When Beep Sound is on, the camcorder sounds a beep when you
press a button.
Press the [MENU] button
[Control (Left/Right)] button
Settings [Control (Up/
Down)] button Beep Sound
[Control (OK)] button.
STBY
[220Min]
1
1
Press the [MENU] button
[Control (Left/Right)] button
Settings [Control (Up/Down)]
button Shutter Sound
[Control (OK)] button.
STBY
[220Min]
Settings
Settings
LCD
:
LCD
:
:
:
Auto LCD Off
Beep Sound
Shutter Sound
Auto LCD Off
Beep Sound
Shutter Sound
:
:
Exit
Exit
Select the desired submenu item
with the [Control (Up/Down)]
button, and then press the
[Control (OK)] button.
2
3
2
3
Select the desired submenu item
with the [Control (Up/Down)]
button, and then press the
[Control (OK)] button.
STBY
[220Min]
STBY
[220Min]
Settings
Settings
Auto LCD Off
Beep Sound
Shutter Sound
Auto LCD Off
Beep Sound
Shutter Sound
Off
On
Off
On
Press the [MENU] button to exit
the menu.
Press the [MENU] button to exit
the menu.
Exit
Exit
Submenu Items
Submenu Items
Items
Use
To turn the shutter sound off.
Items
Off
Use
Off
Disables the function.
To have the camcorder beep every time you press a button.
To turn the shutter sound on. It will sound when you press the
[PHOTO] button.
On
On
The Beep Sound function is suspended in the following situations:
-
-
-
During recording and playback
During a pause while recording
When the camcorder has a cable connection. (AV cable, micro HDMI
cable, etc.)
78
Other settings
Auto Power Off
PC Software
If you set PC Software to On, you can use the built-in PC software
easily by connecting a USB cable between the camcorder and your
PC. Using the software, you can download stored video and photo
images on the camcorder to your PC’s hard disk. You can also edit
video and photo files using the PC software.
You can set your camcorder to turn off automatically if it is idle for 5
minutes without an operation. This function will prevent unnecessary
power consumption.
Press the [MENU] button
STBY
[220Min]
1
[Control (Left/Right)] button
Settings [Control (Up/Down)]
button Auto Power Off
[Control (OK)] button.
Settings
1
Press the [MENU] button
[Control (Left/Right)] button
Settings [Control (Up/
Down)] button PC Software
[Control (OK)] button.
STBY
[220Min]
:
:
Auto Power Off
PC Software
Format
Settings
:
:
Auto Power Off
PC Software
Format
Exit
Select the desired submenu item
with the [Control (Up/Down)]
button, and then press the
[Control (OK)] button.
2
3
STBY
[220Min]
Exit
2
3
Select the desired submenu item
with the [Control (Up/Down)]
button, and then press the
[Control (OK)] button.
Settings
STBY
[220Min]
Auto Power Off
PC Software
Format
Off
5 Min
Settings
Press the [MENU] button to exit
the menu.
Auto Power Off
PC Software
Format
Off
On
Exit
Press the [MENU] button to exit
the menu.
Exit
Submenu Items
Submenu Items
Items
Use
Off
To disable the function.
Items
Off
Use
The camcorder turns off if idle for 5 minutes without
performing an operation.
5 Min
To disable the function.
To launch the built-in editing software when you connect the
camcorder to a PC with a USB cable.
On
•
•
Auto Power Off does not work in the following situations:
-
-
If the power cable (Power adaptor, USB cable) is connected.
While the following functions are in operation: Delete: All Files,
Protect: All On.
The PC Software is compatible with Windows operating systems only.
-
While recording, playing back (except when paused), or playing
back a photo slide show.
To operate the camcorder again, press the [Power ( )] button.
79
Other settings
Format
Default Set
You can restore all menu settings to their defaults.
Use the Format function if you want to delete all files completely or
to correct problems on the storage media.
STBY
[220Min]
1
Press the [MENU] button
[Control (Left/Right)] button
Settings [Control (Up/
Down)] button Default Set
[Control (OK)] button.
Settings
Format
Insert a memory card. page 30
Default Set
Language
Press the [MENU] button
1
STBY
[220Min]
Exit
[Control (Left/Right)] button
Settings [Control (Up/Down)]
button Format [Control (OK)]
button.
Settings
2
Select Yes if you want all the
settings returned to the defaults.
:
:
Auto Power Off
PC Software
Format
•
•
•
Do not turn off the power while using this function.
Exit
After resetting the camcorder, reset the Date/Time Set. page 25
The Default Set function does not affect the files recorded on the
storage media.
Select Yes by pressing the
[Control(Left/Right)] button, and
then press the [Control (OK)] button.
2
•
Do not remove the memory card or perform any other operation
(such as turning off the power) during formatting. Also, be sure to
use the provided power adaptor, as the recording media may be
corrupted if the battery becomes exhausted during formatting.
If the storage media becomes corrupted, format it again.
Language
You can select a desired language to display the menu and
messages in. page 29
•
•
•
Do not format the storage media on a PC or other device.
Make sure to format the storage media on this camcorder.
Format the memory card in the following situations:
Open source licenses
Show the Open source licenses information.
-
-
-
-
Before using a new memory card
If the memory card was formatted on other devices
If the memory card was used to record on other devices
If the camcorder cannot read the memory card
•
•
•
A memory card with the protection tab set to lock can not be
formatted.
If there is no storage media inserted, it cannot be selected and will
be dimmed in the menu.
You cannot format when the battery power is insufficient. We
recommend you use the power adaptor to avoid loss of power while
formatting.
80
Connecting to a TV
Using a micro HDMI cable
CONNECTING TO A HIGH DEFINITION TV
WITH HDMI
Turn on the camcorder.
1
You can view High Definition (HD) quality videos recorded in HD
resolution on an HDTV using an HDMI connection. This camcorder
supports HDMI output to deliver high-definition video transfer.
•
If you do not turn on the camcorder first, the camcorder may
fail to recognize the connected TV.
Connect the camcorder to the TV with a micro HDMI cable.
2
3
Set the TV’s input or source selector to the HDMI input you’ve
attached the camcorder to.
HDTV
•
Refer to the TV’s instruction manual to see how to select the
TV’s input or source.
Start to play back images. page 42
4
Understanding the HDMI
HDMI (High Definition Multimedia Interface) is a compact
audio/video interface for transmitting uncompressed digital
data.
Camcorder
•
You can use only a D to A type micro HDMI cable with this
camcorder.
Signal flow
•
•
The HDMI jack on the camcorder is for output only.
Use only HDMI 1.3 cable when connecting to the HDMI jack of this
camcorder. If the camcorder is connected with HDMI cables that are
not version 1.3, the screen display may not work.
Micro HDMI cable
81
Connecting to a TV
CONNECTING TO A REGULAR TV
Stereo Type
Mono Type
You can view images recorded with your camcorder on a regular
TV that supports standard definition. This camcorder supports the
composite output for standard definition video transfer.
Yellow
White
Red
Yellow
TV
White
•
•
When you connect the camcorder to a TV, the LCD screen of the
camcorder turns off automatically.
Make sure you’ve connected the camcorder to the correct input
jacks. The TV screen may not display the right image information if
connected incorrectly.
Camcorder
•
•
•
Do not use excessive force when connecting the cables.
We recommend you use the power adaptor as the power source.
When connecting to a TV using the Audio/Video cable, match the
color of the cables to the color of the corresponding jacks.
Video input may appear green depending on the TV. If this occurs,
connect the yellow plug of the Audio/Video cable to the green jack of
the TV.
If your TV has one audio jack (mono input), connect the yellow plug
of the Audio/Video cable to the video jack, the white plug to the
audio jack, and leave the red plug unconnected.
When you connect the camcorder to a TV using the Audio/Video
cable, images recorded in high definition image quality (1280x720/
30p) play back in standard definition image quality.
When the camcorder is connected to a TV with more than one kind
of cable, the camcorder outputs video signals in the following order
of priority: HDMI Audio/Video (composite) output
Signal flow
•
•
•
•
Audio/Video cable
Connecting an Audio/Video cable for the composite
output
Connect the camcorder to a TV with an Audio/Video cable.
1
•
Turn on the camcorder, and then connect an Audio/
Video cable. If you do not turn on the camcorder first, the
camcorder may fail to recognize the connected TV.
Set the TV’s input or source selector to the input you’ve
attached the camcorder to.
2
3
•
Refer to the TV’s instruction manual to see how to select the
TV input.
82
Start to play back images. page 42
Connecting to a TV
VIEWING ON A TV SCREEN
Image display depending on LCD and TV screen ratio
Appearance on Wide
Recording ratio
Appearance on 4:3 TV
Screen (16:9) TV
Images recorded in
a 16:9 ratio
C
A
R
D
Images recorded in
a 4:3 ratio
Adjust the volume to a moderate level. If the volume is too high, the
video may include noise.
83
Dubbing videos
Insert the storage media into the recording device.
1
2
DUBBING TO VCR OR DVD/HDD
RECORDERS
Connect your camcorder to the recording device (VCR or DVD/
HDD recorders) with the supplied Audio/Video cable.
You can dub images recorded on your camcorder to other recording
devices, such as VCRs or DVD/HDD recorders.
Start recording on the recording device, and then start playback
on the camcorder.
3
•
•
Videos are dubbed to the other recording devices via analog data
transfer (composite connection). Use the supplied Audio/Video
cable.
Use the power adaptor to power the camcorder when you dub to
a VCR or DVD/HDD recorder.
•
Refer to the instruction manuals supplied with your recording
device for details.
When dubbing finishes, stop the recording device, and then your
camcorder.
4
•
•
Videos recorded on this camcorder can only be dubbed using
the Audio/Video cable in SD (standard definition) image quality,
regardless of the recording resolution (HD/SD).
To copy a video recorded in HD (high definition) image quality, use
the built-in software of your camcorder, and then copy the video to
your computer. page 86
VCRs or DVD/ HDD recorders
Camcorder
•
•
Since dubbing is performed via analog data transfer, the image
quality may deteriorate.
To record the date/time, display it on the LCD screen. page 76
Signal flow
Audio/Video cable
84
Using with a windows computer
System Requirements
WHAT YOU CAN DO WITH A WINDOWS
COMPUTER
Your computer must meet the following requirements to run Intelli-
studio:
You can perform the functions listed below by connecting your
camcorder to your Windows computer with a USB cable and using
the Intelli-studio editing software built into your camcorder.
Items
System Requirements
Microsoft Windows XP SP2, Windows Vista, Windows 7, or
higher
OS
Main Functions
Intel® Core 2 Duo® 1.66 GHz or higher is recommended
AMD Athlon™ X2 Dual-Core 2.2 GHz or higher is
recommended
(Notebook: Intel Core2 Duo 2.2GHz or AMD Athlon X2 Dual-
Core 2.6GHz or higher is recommended)
•
•
Intelli-studio editing software’s main functions
CPU
RAM
-
-
-
Playing back recorded videos or photos.
Editing recorded videos or photos.
Uploading the recorded videos and photos to YouTube,
Flickr or Facebook, etc.
1GB or higher is recommended
You can transfer or copy the files (videos and photos) saved on
the storage media into your computer.
NVIDIA GeForce 8500 GT or higher,
ATI Radeon HD 2600 series or higher
Video Card
Display
1024 x 768, 16-bit color or higher (1280 x 1024, 32-bit color
recommended)
USB
USB 2.0
Direct X
DirectX 9.0c or higher
Recommended
Memory Card
(Installed in
6MB/s (Class 6) or above
Camcorder)
•
System requirements mentioned above are recommendations. Even
on a system that satisfies the requirements, Intelli-studio may not
operate optimally.
•
•
•
•
On a slower than recommended computer, video playback may skip
frames or operate in an unexpected manner.
If the version of DirectX on your computer is lower than 9.0c, install
DirectX 9.0c or higher.
We recommended you transfer recorded videos to a PC before
playing back or editing the videos.
To run Intelli-studio, a laptop computer requires faster and better
components than a desktop PC.
Intelli-studio is not Mac OS compliant.
On 64-bit environment of Windows XP, Windows Vista, and Windows
7, Intelli-studio may be installed and work as 32-bit program.
•
•
85
Using with a windows computer
Click Yes in the new file saving window. The uploading
procedure starts. Click Yes to confirm.
3
USING THE Intelli-studio PROGRAM
Intelli-studio is a built-in program that allows you to play back and
edit files. You can upload files to web sites, such as YouTube or
Flickr.
•
If you do not want to save any new files, select No.
Step 1. Connecting the USB cable
Set PC Software to On.
1
To disconnect the USB cable
To disconnect the USB cable after completing the file transfer, you
must follow these steps:
•
This is the default setting.
2
Connect the camcorder to a PC with the USB cable.
•
•
A new file saving window appears along with the Intelli-studio
main window. If your camcorder has no new files, the pop-up
window for saving new files will not appear.
Depending on your version of Windows, the Windows
removable disk window may also appear.
1. Click the Safely Remove Hardware icon on the taskbar.
2. Select USB Mass Storage Device, and then click Stop.
3. If the Stop a Hardware device window appears, click OK.
4. Disconnect the USB cable from the camcorder and PC.
•
•
Use the provided USB cable. (Supplied by Samsung)
Make sure you insert the USB plug into the USB jack with the plug oriented
in the correct direction.
•
•
•
When the USB cable is connected, turning the camcorder on or off may
cause the PC to malfunction.
CA
If you disconnect the USB cable from the PC or the camcorder while
transferring files, data transmission will stop and the data may be damaged.
If you connect the camcorder to a PC via a USB HUB or simultaneously
connect the camcorder along with other USB devices, the camcorder may
not work properly. If this occurs, remove all USB devices from the PC, and
then reconnect the camcorder.
Intelli-studio may not automatically run. If this occurs, access My Computer
or Windows Explorer, open the drive that corresponds to your camcorder,
find Intelli-studio, and then run iStudio.exe.
•
86
Using with a windows computer
Step 2. About the Intelli-studio main window
For details, select Help Help on the
Intelli-studio screen.
When the Intelli-studio starts up, video and photo thumbnails appear
in the main window.
1
2 3
4
5
6
7
No.
1
2
3
4
5
6
7
8
9
0
!
@
#
$
Description
%
$
Menu items
Display files in the selected folder.
Switch to Photo edit mode.
#
8
9
Switch to Video edit mode.
Switch to Share mode.
Enlarge or reduce the thumbnails in the list.
Select a file type.
@
0
!
View videos and photos of the selected folder on your computer.
Show or hide videos and photos of the connected device.
View videos and photos of the selected folder on the device.
View files as thumbnails or on a map.
Browse folders in the connected device.
Browse folders stored on your computer.
Move to the previous or next folder.
•
If you install Intelli-studio on your PC, the program will launch more
quickly. To install the program, select Tool Install Intelli-studio
on PC.
You can update the latest version of Intelli-studio software by clicking
on Web Support Update Intelli-studio Start Update.
The camcorder’s built-in Intelli-studio software is intended for
home use. It is not for precision or industrial productions. For these
applications, we recommend an editing software designed for
professional use.
•
•
Print files, view files on a map, store files in Contents Manager, or
register faces.
%
87
Using with a windows computer
Step 3. Playing back videos or photos
Step 4. Editing videos or photos
You can play back the recordings conveniently using the Intelli-
studio application.
You can edit the videos or photos in various ways with various
functions. (Change Size, Fine-Tuning, Image Effect, Insert Frame,
etc.) Before editing a video or photo in Intelli-studio, make a backup
copy of the video or photo file and store it on your computer for
safe-keeping using My Computer or Windows Explorer.
1
With Intelli-studio, click the desired folder to display your
recordings.
•
Video or photo thumbnails appear on the screen, depending
on the folder you selected.
1
2
Choose the videos or photos you want to edit.
2
Choose the video or photo that you want to play back.
Click Movie Edit ( ) or Photo Edit ( ) depending on the file
you selected in the Intelli-studio browser.
•
You can view the file information by moving the mouse over
the file.
•
The selected file appears in the editing window.
•
If you click a video thumbnail once, the video plays back
inside the thumbnail frame, allowing you to search for a
desired scene with ease.
Edit a video or photo with various edit functions.
3
3
After you select the video or photo you want, double-click to
play back.
•
Playback starts and the controls appear.
Intelli-studio supports the following file formats:
- Video formats: MP4 (Video: H.264, Audio: AAC), WMV (WMV 7/8/9)
- Photo formats: JPG, GIF, BMP, PNG, TIFF
88
Using with a windows computer
Step 5. Sharing the videos/photos online
Click Upload to start uploading.
4
•
A pop-up window appears. The window will either ask you
to enter your ID and password or ask you to click OK to
continue to the web site you have selected.
Share your contents with the world by uploading photos and videos
directly to a web site with one click.
1
2
Choose the videos or photos you want to share.
Click Share ( ) on the Intelli-studio browser.
•
The selected files appear in the sharing window.
5
Enter your ID and the password to access.
•
Access to the web site contents can be limited depending on
your web access environment.
Click the web site you would like to upload files to.
3
The allowed total recording time for individual videos and the capacity
available for uploading videos can differ, depending on each web site’s
policy.
•
You can choose YouTube, twitter, flickr, facebook, Picasa,
Email, or another web site you want to use for your site
management.
89
Using with a windows computer
UPLOAD YOUR VIDEOS DIRECTLY TO YOUTUBE!
The One-Press [Share (
)] button lets you directly upload and share your videos on YouTube. Just press the [Share (
)] button while your
product is connected to a Windows computer using the USB cable.
STEP 1
STEP 3
On the product, select a video you want to upload in the video
Press the [Share (
a Windows computer.
)] button while your product is connected to
thumbnail index view using the [Share (
)] button. Repeat for
•
A pop-up sharing window displaying
the videos with share marks appears
on the screen.
each video you want to upload. page 73
•
The Share mark (
) appears on each video.
Normal
0:00:55
•
•
Click Yes on the PC screen to begin
uploading your videos to YouTube.
If you want to upload directly without
showing a pop-up sharing window,
check “Intelli-studio does not pop
a list of share marked files from the
connected device”.
1/10
Photo
Move
Play
•
You can use the [Share (
)] button only while Intelli-studio is running.
STEP 2
Connect the product to a PC with the USB cable.
•
If you have set PC Software: On, Intelli-studio runs automatically on a
Windows computer after you’ve connected the product.
•
•
As part of the uploading process, the videos you marked are converted into a format playable by
YouTube before actually uploading. Time spent uploading may vary depending on such conditions as
file size, computer performance, and network speed.
There is no guarantee the uploading operation will work in all environments. YouTube server-side
changes in the future may disable this function.
CAR
D
•
•
For more information on YouTube, visit the YouTube website: http://www.youtube.com/
This product’s YouTube uploading functionality is provided under the license from YouTube LLC.
The presence of the YouTube uploading functionality in this product is not an endorsement of or
recommendation for the product by YouTube LLC.
•
•
If you do not have an account on a specified website, you must register first before you can upload.
According to YouTube’s policy, direct video uploading may not be available in your nation/region.
90
Using with a windows computer
The folders in the storage media appear.
4
5
USING AS A REMOVABLE STORAGE DEVICE
•
Different file types are stored in different folders.
You can transfer recorded data to a Windows computer by
connecting the USB cable to the camcorder.
Copy and paste or drag and drop the files from the storage
media to your PC.
Viewing and transferring the contents of storage media
•
If the Removable Disk window does not appear, confirm the
connection (page 86) or repeat steps 1 through 3 again. If the
removable disk does not appear automatically, open the removable
disk folder using My Computer or Windows Explorer.
If the connected camcorder’s disk drive does not open or the
context menu that appears when right-clicking your mouse (open
or browse) appears broken, your computer may be infected by an
Autorun virus. Be sure to update your antivirus software to the latest
version.
Set PC Software to Off.
page 79
1
•
Insert a memory card.
page 30
2
Connect the camcorder to the
PC with the USB cable.
3
page 86
•
The Removable Disk or
Samsung window appears
on the PC’s screen after a
moment.
Select Open folders to
view files using Windows
Explorer and then click
OK.
•
Photos Videos
System folder
Setting folder
91
Using with a windows computer
Structure of folders and files on the storage media
•
•
The folder and file structure for the storage media is shown
below.
Do not arbitrarily change or remove the folder or file name. It may
not be playable.
Videos (H.264)
①
•
•
•
HD-quality videos have an HDV_####.MP4 name format.
SD-quality videos have an SDV_####.MP4 name format.
The file number automatically increases when a new video clip file
is created.
•
•
•
Up to 9,999 files can be stored in one folder. A new folder is
created when the number files in a folder exceeds 9,999.
The folder names are given in the following order: 100VIDEO,
101VIDEO, etc. The maximum number of folders is 999.
The camcorder can create a maximum of 9,999 files in a storage
media.
File format
Video files
•
•
Videos are compressed in H.264 format. The file extension is
‘.MP4’.
Refer to page 53 for video resolution.
Photos
②
•
•
•
As with video clip files, the file number automatically increases
when a new image file is created.
Photo files have a SAM_####.JPG format. A new folder stores
files starting with SAM_0001.JPG.
Folder names increase in this order: 100PHOTO101PHOTO
etc.
Photo files
•
Photos are compressed in JPEG (Joint Photographic Experts
Group) format. The file extension is ‘.JPG’.
•
Refer to page 54 for photo resolution.
Do not modify the name of a movie file recorded by the camcorder.
For proper playback, the camcorder requires the original folder and file
name.
92
Troubleshooting
WARNING INDICATORS AND MESSAGES
Before contacting a Samsung authorized service center, perform the following simple checks. They may save you the time and expense of an
unnecessary call.
Power source
Message
Low Battery
Icon
Informs that...
Action
•
•
Replace with a charged battery or use the power adaptor.
Charge the battery.
-
The battery is almost discharged.
•
•
Check the battery’s authenticity. Change to an authentic and charged Samsung
battery.
We recommend you use only genuine Samsung batteries in this camcorder.
Check authenticity of the
battery.
-
The battery failed to authenticate.
This is not a rated
adaptor.
Use only the rated
adaptor that we
provided.
•
•
Check the power adaptor’s authenticity.
We recommend you use only genuine Samsung power adaptors for this
camcorder.
The power adaptor failed to
authenticate.
Storage media
Message
Icon
Informs that...
Action
There is no memory card inserted in
the memory card slot.
•
•
Insert a memory card.
Insert Card
Card Full
There is not enough space to record
on the memory card.
Back-up important files to your PC or another storage media and delete
unnecessary files in the memory card.
The memory card has some problem
and cannot be recognized.
•
•
Format the memory card or replace it with a new one.
Release the write protection tab.
Card Error
Card Locked
The write protection tab on the
memory card has been set to lock.
93
Troubleshooting
Storage media
Message
Icon
Informs that...
Action
The memory card is not supported in
this camcorder.
Not Supported Card
Please format
•
•
Change to a memory card that we recommended.
Format the memory card using the menu.
The memory card is not formatted.
Low speed card.
Please record a lower
resolution.
The memory card is not fast enough
to record at this resolution.
•
•
Record video at a lower resolution.
Change the memory card to a faster one. page 32
-
Recording
Message
Icon
Informs that...
Action
Some problems occurred while writing
data to the storage media.
•
•
Format the storage media using the menu after backing-up important files
to your PC or another storage media.
Write Error
-
You cannot operate some functions
manually when SMART AUTO is
activated.
Release the Smart Auto
-
Turn off the SMART AUTO function.
•
•
•
•
•
Delete unnecessary files from the storage media.
Back up files to your PC or another storage media and delete files.
Change to another card which has enough free space.
Set File No. to Reset.
The number of video files that can be
stored is 9,999.
The card has reached maximum
capacity. No more files can be stored.
The number of video files is
full.
Cannot record video.
-
Format the storage media.
•
•
•
•
•
Delete unnecessary files on the storage media.
Back up files to your PC or another storage media and delete files.
Change to another card which has enough free space.
Set File No. to Reset.
The number of photo files that can be
stored is 9,999.
The card has reached maximum
capacity. No more files can be stored.
The number of photo files is
full.
Cannot take a photo.
-
94
Format the storage media.
Troubleshooting
Recording
Message
Icon
Informs that...
Action
Folder and file number have reached
the maximum number. You cannot
record additional videos.
File number is full.
Cannot record video.
•
•
Set File No. to Reset and format the storage media. Remember to back up
important files before formatting.
-
Folder and file number have reached
the maximum number. You cannot
record additional photos.
File number is full.
Cannot take a photo.
Set File No. to Reset and format the storage media. Remember to back up
important files before formatting.
-
Check the lens cover.
Lens cover is closed.
•
Open the lens cover.
Playback
Message
Icon
Informs that...
Action
Some problems occurred when
reading data from the storage media.
•
•
Format the storage media using the menu after backing up important files
to PC or another storage device.
Read Error
-
Format the storage media after backing up important files to a PC or
another storage device.
Corrupted file
This file cannot be read.
-
95
Troubleshooting
SYMPTOMS AND SOLUTIONS
If these instructions do not solve your problem, contact the nearest Samsung authorized service center.
Power
Symptom
Explanation/Solution
•
•
•
•
The battery may not be installed on your camcorder. Insert a battery into the camcorder.
The inserted battery may be discharged. Charge the battery or replace it with a charged one.
If you use a power adaptor, make sure it is properly connected to the wall outlet.
Remove the battery or unplug the power adaptor, and then reconnect the power supply to the
camcorder before turning it on.
The camcorder does not turn on.
•
•
•
If no button is pressed for about 5 minutes, the camcorder is automatically turned off (Auto Power Off).
To disable this option, change the setting of Auto Power Off to Off.
Use the power adaptor.
The power automatically turns off.
Remove the battery or unplug the power adaptor, and then reconnect the power supply to the
camcorder before turning it on.
Power cannot be turned off .
•
•
•
The temperature is too low.
The battery is not fully charged. Recharge the battery.
The battery has reached the end of its lifespan and cannot be recharged. Use another battery.
The battery is quickly discharged.
Displays
Symptom
Explanation/Solution
•
This can occur when recording or viewing a 16:9-ratio image on a 4:3-ratio TV, or vice versa. For more
details, see display specifications. page 83
The TV screen or LCD display has distorted images
or has stripes at the top/ bottom or on the left/right.
96
Troubleshooting
Displays
Symptom
Explanation/Solution
Unknown indicator appears on the screen.
An afterimage remains on the LCD screen.
The image on the LCD screen looks dark.
•
•
•
A warning indicator or message appears on the screen. pages 93~95
This occurs if you disconnect the power adaptor or remove the battery before turning the power off.
Ambient light is too bright. Adjust the brightness and angle of the LCD.
Storage media
Symptom
Explanation/Solution
•
•
Insert a memory card into your camcorder properly. page 30
If you use a memory card formatted on a computer, format it again directly on your camcorder. page 80
Memory card functions are not operable.
Image cannot be deleted.
•
•
You cannot delete the images protected by another device. Release the protection of the image on the
device. page 72
Release the lock on the write-protect tab of the memory card (SDHC memory card, etc.), if any page 31
.
•
•
Release the lock on the write-protect tab of the memory card (SDHC memory card, etc.), if any. page 31
The memory card is not supported on your camcorder or the card has some problems.
You cannot format the memory card.
The data file name is not indicated correctly.
•
•
•
The file may be corrupted.
The file format is not supported by your camcorder.
Only the file name appears if the directory structure does not comply with the international standard.
Your computer does not recognize an SDXC memory
card.
•
SDXC memory cards use the exFAT file system. To use SDXC memory cards on a Windows XP computer,
download and update the exFAT file system driver from the Microsoft website.
Your TV or computer cannot display photos and
videos that are stored on an SDXC memory card.
•
SDXC memory cards use the exFAT file system. Ensure that the external device is compatible with the
exFAT file system before connecting the product to the device.
97
Troubleshooting
Recording
Symptom
Explanation/Solution
•
•
•
There is not enough free space to record on the storage media.
Make sure the memory card is inserted and write-protect tab is set to unlock.
The internal temperature of your camcorder is unusually high.
Turn off your camcorder and leave it for a while in a cool place.
Your camcorder is damp and moist inside (condensation).
Pressing the [Recording start/stop] button does
not start recording.
•
Turn off your camcorder and leave it for about 1 hour in a cool place.
•
•
The estimated recording time may vary depending on the contents and the features you used.
Recording a fast-moving subject increases the bit rate and consequently the amount of storage space
required for the recording, which can lead to a shorter available recording time.
The actual recording time is less than the estimated
time.
•
•
•
There is no more free space for recording on the storage media.
Back up important files to your PC, and then format the storage media or delete the unnecessary files.
If you frequently record or delete files, the performance of the storage media will deteriorate.
In this case, reformat the storage media.
If you use a memory card with a low writing speed, the camcorder automatically stops recording the
videos and the corresponding message appears on the LCD screen.
The recording stops automatically.
When recording a subject illuminated by bright light,
vertical lines appear.
•
The camcorder is unable to record these levels of brightness.
98
Troubleshooting
Recording
Symptom
Explanation/Solution
When the screen is exposed to direct sunlight during
recording, the screen turns red or black for an
instant.
•
•
Do not expose the LCD screen to direct sunlight.
During recording, the date/time does not appear.
The beep sound is not heard.
Set Date/Time Display to on. page 76
•
•
•
Set the Beep Sound to On.
The beep sound is temporally off while the camcorder records videos.
When the Audio/Video cable jack or micro HDMI cable jack is connected to the camcorder, the beep
sound will automatically turn off.
There is a time difference between the point where
you press the [Recording start/stop] button and
the point where the recorded video starts/stops.
•
On your camcorder, there may be a slight time delay between the point where you press the [Recording
start/stop] button and the actual point where the recorded video starts/stops. This is not an error.
•
•
•
Set your camcorder to the recording mode. page 26
Release the lock on the write-protection tab of the memory card if set. page 31
The storage media is full.
Use a new memory card or format the storage media. page 80
Remove unnecessary images. page 70
You cannot record a photo image.
99
Troubleshooting
Adjusting the image during recording
Symptom
Explanation/Solution
•
•
Set Focus to Auto. page 58
The recording conditions are not suitable for auto focus.
Adjust the focus manually. page 58
Focus does not adjust automatically.
•
•
The lens is dusty on the surface. Clean the lens and check the focus.
You are recording in a dark place. Increase the brightness.
The image appears too bright or flickering, or
changes in color.
•
This occurs when recording images under a fluorescent lamp, sodium lamp, or mercury lamp. Cancel
iSCENE to minimize these phenomena. page 52
Playback on your camcorder
Symptom
Explanation/Solution
•
•
•
Press the [MODE] button to set the video playback mode.
Image files recorded on another camcorder may not play back on your camcorder.
Check out memory card compatibility. page 31
The video does not play back.
•
If the temperature inside the camcorder is too high, it cannot function properly.
Turn the camcorder off, wait for a few moments, and then turn it on again.
The Skip or Search function does not work properly.
Playback is interrupted unexpectedly.
•
•
Check if the power adaptor or battery is properly connected and stable.
You cannot hear sound when playing back a Time
Lapse recording.
The Time Lapse REC function does not record sound.
Photos stored on a storage media do not appear in
the actual size.
•
Photos recorded on other devices may not appear at their actual size. This is not an error.
Playback on other devices (TV, etc.)
Symptom
Explanation/Solution
•
•
Connect the audio line of the Audio/Video cable jack to your camcorder and the connected device (TV,
DVD recorder, etc). (Red color- right, White color- left)
The Audio/Video cable jack or micro HDMI cable jack is not connected properly. Make sure that the
Audio/Video cable jack or micro HDMI cable jack is connected to the proper jack. page 82
You cannot view the image or hear the sound on the
connected device.
100
You cannot dub correctly using the HDMI cable.
•
You cannot dub images using the HDMI cable.
Troubleshooting
Connecting to a computer
Symptom
Explanation/Solution
When accessing videos, a computer does not
recognize your camcorder.
•
Disconnect the USB cable from the computer and camcorder, restart the computer, then reconnect it
correctly.
•
•
You need to install a video codec on the PC to play back the files recorded by your camcorder. Install or
run the internal edit software (Intelli-studio).
Make sure you insert the connector in the correct direction, and connect the USB cable to the USB
jack on your camcorder firmly. Disconnect the cable from the computer and camcorder, restart the
computer. Reconnect it properly.
Cannot play back a video file properly on a PC.
•
Your computer may not have the necessary performance specifications to play back a video file. Check
the recommended computer specifications.
•
•
•
Exit the Intelli-studio application, and restart the Windows computer.
Intelli-studio is not Mac OS compliant.
Set PC Software to On in the Settings menu.
Intelli-studio does not function properly.
•
•
The image or sound of the video file may stop playing back temporarily depending on the data transfer
speed of PC. Copy the video file to your PC and then play it back on the PC.
If you connect the camcorder to your PC that the PC does not support Hi-Speed USB (USB2.0),
the image or sound of the video file may not play back correctly. Video files copied to the PC are not
affected by it.
The image or sound of the video file recorded by
your camcorder does not play back correctly on
your PC.
•
•
•
Check the system requirements to play back a video. page 85
Exit all other applications running on the computer.
If you play back the recorded file by connecting the camcorder to your PC, the file may not play back
smoothly depending on the data transfer speed of PC.
The playback screen is paused or distorted.
101
Troubleshooting
Dubbing with other devices
Symptom
Explanation/Solution
•
The Audio/Video cable is not connected properly. Make sure that the Audio/Video cable is connected to
the proper jacks, i.e. to the input jacks of the device used for dubbing an image from your camcorder.
page 84
You cannot dub correctly using the Audio/Video
cable.
General operations
Symptom
Explanation/Solution
•
•
Has the camcorder been left unused for a long period of time?
The backup internal rechargeable battery may be discharged. page 25
The date and time are incorrect.
Pressing a button will not turn on or operate the
camcorder.
Remove the battery or unplug the power adaptor, and then reconnect the power supply to the
camcorder before turning it on.
Menu items that cannot be used at the same time
Symptom
Explanation/Solution
•
You cannot select grayed items in the menu. If you have not inserted a memory card into the camcorder,
all functions that require a memory card (Storage Info, Format, etc.) are grayed in the menu and you
cannot select them. Insert a memory card to select and use these functions.
Cannot use
Anti-Shake(HDIS)
Face Detection
Back light
Because of the following settings
Menu items are grayed out.
Digital Special Effect
C.Nite, Intelli Zoom
Video Resolution : 1280x720/30p
102
Maintenance & additional information
•
To clean the lens
MAINTENANCE
Use a air brush to remove dust, and then wipe the lens gently
with a soft cloth.
If necessary, wipe gently with lens paper or tissue.
Cautions when storing
-
-
Mold may form on the lens if the lens is left dirty.
If the lens looks dim, turn off the camcorder and leave it off for
about 1 hour.
•
To store your camcorder safely, turn it off.
-
-
Remove the battery and power adaptor.
Remove the memory card.
Cleaning the camcorder
Before cleaning, turn off the camcorder and remove the battery
and power adaptor.
•
To clean the exterior
-
Wipe gently with a soft dry cloth. Do not apply excessive force
when cleaning. Gently rub the surface.
-
Do not use benzene or thinner to clean the camcorder. The
exterior coating could peel off or the case could deteriorate.
LCD screen
•
To clean the LCD screen
Wipe very gently with a soft dry cloth. Be careful not to damage
the screen.
•
To prolong its service life, do not rub the LCD screen with a
coarse cloth.
Be aware of the following LCD screen phenomena. They are
not malfunctions.
•
-
-
-
When you use the camcorder, the surface around the LCD
screen may heat up.
If you leave the power on for a long time, the surface around
the LCD screen becomes hot.
When using the camcorder in cold conditions, an afterimage
may appear on the LCD screen.
•
An LCD screen is manufactured using advanced technology
which creates screens with pixel failure rates of less than 0.01%.
However, a black or bright spot (red, blue, white) may appear in
the center of the LCD screen and up to two spots may appear
outside the center. These spots, which are normally incurred
during the manufacturing process, do not affect the recorded
images.
103
Maintenance & additional information
USING YOUR CAMCORDER ABROAD
When there is dew condensation, put the camcorder aside
for a while before using
•
•
Each country or region has its own electric and color systems.
Before using your camcorder abroad, check the following items.
•
•
•
What is dew condensation?
Dew condensation happens when a camcorder is moved to a
location where there is a significant temperature difference from
the previous location. The dew condenses on the external or
internal parts of the camcorder, and on the reflection lens. If there
is dew on or in your camcorder, it may cause the camcorder to
malfunction or damage the camcorder when you turn the power
on.
Power sources
The power adaptor provided lets you power, recharge, and use your
camcorder in any country/region that has the power in the 100 V to
240 V, 50/60 Hz range. You may need a commercially available AC
plug adaptor depending on the design of local wall outlets.
Exactly when does dew condensation occur?
When you move the camera to a location with a higher
temperature than the previous location, or when you move it to a
hot area suddenly. Examples:
On TV color systems
Your camcorder is an NTSC based camcorder. If you want to view
your recordings on a TV or copy them to an external device, it must
be an NTSC based TV or external device and have the appropriate
Audio/Video jacks. Otherwise, you may need to use a separate
video format transcoder (For example, an NTSC to PAL format
converter).
-
You record outside in cold weather during the winter and
then move the camera in indoors.
-
You record outside in hot weather after being indoors or
inside a car where the A/C was running.
What can I do?
Turn the power off, detach the battery, and leave the
camcorder in a dry area for 1~2 hours before using it.
-
The format transcoder is not provided by Samsung.
•
•
Use the camcorder only after dew condensation has completely
disappeared.
Be sure to use the recommended accessories supplied with the
camcorder. For service, contact your nearest Samsung authorized
service center.
NTSC-compatible countries/regions
Bahamas, Canada, Central America, Japan, Korea, Mexico,
Philippines, Taiwan, United States of America, etc.
PAL-compatible countries/regions
Australia, Austria, Belgium, Bulgaria, China, CIS, Czech
Republic, Denmark, Egypt, Finland, France, Germany, Greece,
Great Britain, Holland, Hong Kong, Hungary, India, Iran,
Iraq, Kuwait, Libya, Malaysia, Mauritius, Norway, Romania,
Saudi Arabia, Singapore, Slovak Republic, Spain, Sweden,
Switzerland, Syria, Thailand, Tunisia, etc.
You can make recordings with your camcorder and view pictures
on the LCD screen anywhere in the world.
104
Maintenance & additional information
Focal length (f)
GLOSSARY
The distance from the middle of the lens to its focal point (in millimeters). Longer focal
lengths result in narrower angles of view and the subject is magnified. Shorter focal
lengths result in wider angles of view.
AF (Auto Focus)
A system that automatically focuses the camcorder lens on the subject. Your
camcorder uses contrast to focus automatically.
F. No (F-Number)
The F-number defines the ratio of the focal length to the size of the lens aperture
(focal length/diameter of lens aperture). The smaller the F-number, the larger the lens
aperture and the greater the amount of light that reaches the camcorder’s sensor.
Generally, smaller F-numbers provide brighter images.
Aperture
The aperture controls the amount of light that reaches the camcorder’s sensor.
Camcorder shake (Blur)
MPEG-4 AVC/H.264
If the camcorder is moved while the shutter is open, the entire image may appear
blurred. This occurs more often when the shutter speed is slow. Prevent camcorder
shake by raising the sensitivity or using a faster shutter speed. Alternately, use a
tripod or the DIS or OIS function to stabilize the camcorder.
MPEG-4 AVC/H.264 defines the latest video coding format standardized by the
ISOIEC and the ITU-T, in 2003. Compared with the conventional MPEG-2 format,
MPEG-4 AVC/H.264 has more than twice the efficiency. Your camcorder employs
MPEG-4 AVC/H.264 to encode high definition videos.
Composition
Composition in photography means arranging objects in a photo. Usually, abiding by
the rule of thirds leads to a good composition.
Optical zoom
This is a general zoom which can enlarge images with the lens alone and does not
degrade the quality of images.
Complementary Metal-Oxide-Semiconductor (CMOS)
A CMOS is an image sensor that produces images approaching the quality of CCD
(charge coupled device) sensors. It consumes less power, meaning the battery on
your camcorder lasts longer before it needs recharging.
Quality
An expression of the rate of compression used in a digital image. Higher quality
images have a lower rate of compression, which usually results in a larger file size.
Digital zoom
Resolution
A feature that artificially increases the amount of zoom available with the zoom lens
(Optical zoom). When using the Digital zoom, the image quality will deteriorate as the
magnification increases.
The number of pixels present in a digital image. High resolution images contain more
pixels and typically show more detail than low resolution images.
Shutter speed
Effective Pixel Count
Shutter speed refers to the amount of time it takes to open and close the shutter,
and it is an important factor in the brightness of a photo, as it controls the amount
of light which pass through the aperture before it reaches the image sensor. A fast
shutter speed provides less time for light to enter. The photo becomes darker, but
more easily freezes subjects in motion.
Unlike the total pixel count, this is the actual number of pixels used to capture an
image.
EV (Exposure Value)
All the combinations of the camcorder’s shutter speed and lens aperture that result
in the same exposure.
White balance (color balance)
An adjustment of the intensities of colors (typically the primary colors red, green, and
blue) in an image. The goal of adjusting the white balance, or color balance, is to
correctly render the colors in an image.
Exposure
The amount of light allowed to reach the camcorder’s sensor. Exposure is controlled
by a combination of the shutter speed, the aperture value, and ISO sensitivity.
105
Specifications
HMX-F90/HMX-F91/HMX-F900/HMX-F910/HMX-F920
Model name
Video signal
NTSC
Picture compression format
Audio compression format
Image device
H.264/AVC
AAC (Advanced Audio Coding)
1/3.2” CMOS
System
Effective pixels
Approx. 920,000 pixels
Total pixels
Approx. 5 Mega pixels
Lens
1.8 to 4.9, 52x (Optical), 70x (Intelli), 130x (Digital) Electronic zoom lens
2.1mm~109.2mm
Focal length
Size/dot number
LCD screen method
Composite video out
Audio output
2.7 inches wide, 230k
LCD screen
Connectors
TFT active matrix system
1.0V (p_p), 75 , analog
Ω
-7.5dBm 47K , analog, stereo
Ω
HDMI output
D type connector (Micro HDMI)
USB output
mini USB-B type (USB2.0 High Speed)
5.0V (Using the power adaptor), 3.7V (Using Lithium Ion battery)
Power supply (100V~240V) 50/60Hz, Lithium Ion battery
2.4W ( LCD on)
Power source
Power source type
Power consumption
Operating temperature
Operating humidity
Storage temperature
Dimensions (W x H x D)
Weight
32˚F~104˚F (0˚C~40˚C)
10% ~80%
General
-4˚F~140˚F (-20˚C~60˚C)
Approx. 2.05''×2.3''×4.43'' (53.9mm×56.4mm×119.0mm)
Approx. 222g (0.489lb) (without battery and memory card)
Omni-directional stereo microphone
Internal MIC
106
※
The technical specifications and design may be changed without notice.
Warranty
SAMSUNG
LIMITED WARRANTY
SAMSUNG Electronics America Inc. (SEA), warrants that this product is free from defective material and workmanship.
SEA further warrants that if product fails to operate properly within the specified warranty period and the failure is due to improper
workmanship or defective material, SEA will repair or replace the product at it’s option.
All warranty repairs must be performed by a SEA authorized service center. The name and address of the location nearest you can be
obtained by calling toll free: 1-800 SAMSUNG (1-800-726-7864).
Labor
1 year carry-in
Parts
1 year
On carry-in models, transportation to and from the service center is the customer’s responsibility.
The original dated sales receipt must be retained by the customer and is the only acceptable proof of purchase.
It must be presented to the authorized service center.
EXCLUSIONS (WHAT IS NOT COVERED)
This warranty does not cover damage due to accident, fire, flood and/or other acts of God; misuse, incorrect line voltage, improper
installation, improper or unauthorized repairs, commercial use, or damage that occurs in shipping.
Exterior and interior finish, lamps, and glass are not covered under this warranty.
Customer adjustments which are explained in the instruction manual are not covered under the terms of this warranty.
This warranty will automatically be voided for any unit found with a missing or altered serial number. This warranty is valid only on products
purchased in the United States and Puerto Rico.
Some States do not allow the exclusions or limitations of incidental or consequential damages, or allow limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from State to State.
Correct disposal of batteries in this product
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection
systems)
(Applicable in countries with separate collection
systems)
This marking on the battery, manual or packaging
indicates that the batteries in this product should not
be disposed of with other household waste at the
end of their working life. Where marked, the chemical
symbols Hg, Cd or Pb indicate that the battery contains
mercury, cadmium or lead above the reference levels
in EC Directive 2006/66. If batteries are not properly
disposed of, these substances can cause harm to
human health or the environment.
This marking on the product, accessories or literature
indicates that the product and its electronic accessories
(e.g. charger, headset, USB cable) should not be
disposed of with other household waste at the end
of their working life. To prevent possible harm to the
environment or human health from uncontrolled waste
disposal, please separate these items from other types
of waste and recycle them responsibly to promote the
sustainable reuse of material resources.
To protect natural resources and to promote material
reuse, please separate batteries from other types of
waste and recycle them through your local, free battery
return system.
Household users should contact either the retailer
where they purchased this product, or their local
government office, for details of where and how they
can take these items for environmentally safe recycling.
Business users should contact their supplier and check
the terms and conditions of the purchase contract. This
product and its electronic accessories should not be
mixed with other commercial wastes for disposal.
QUESTIONS OR COMMENTS?
COUNTRY
CALL
OR VISIT US ONLINE AT
WRITE
1-800-SAMSUNG
(726-7864)
Samsung Electronics America, lnc.
85 Challenger Road Ridgefield Park, NJ 07660
IN THE US
www.samsung.com
RoHS compliant
Our product complies with “The Restriction Of the use of certain Hazardous Substances in electrical and electronic equipment”, and we
do not use the 6 hazardous materials- Cadmium (Cd), Lead (Pb), Mercury (Hg), Hexavalent Chromium (Cr +6), Poly Brominated Biphenyls
(PBBs), Poly Brominated Diphenyl Ethers (PBDEs)- in our products.
|
Yorkville Sound Car Speaker U15 User Manual
West Bend Back to Basics SMOOTHIE FREEZE SUP400BINST User Manual
Weil McLain FLAME GUARDIAN WMBC 1A User Manual
Southwestern Bell Speaker CM860 User Manual
Sony DCR User Manual
Sanyo KHS1822 User Manual
Samsung HMX Q11BP User Manual
Samsung AWEP700JBE User Manual
Salton HB 1094 User Manual
Rosewill ATX Computer Case R9859 User Manual