Rockford Fosgate PCH 314 User Manual

®
I
SS  
HIGH DEFINITION  
COMPONENT SYSTEMS  
PCH-14X  
PCH-314 / PCH-414  
PCH-514 / PCH-614  
INSTALLATION & OPERATION  
®
®
TABL E O F C O N T E N T S  
Package Contents .................................................................................... 1  
Introduction ............................................................................................ 1  
Technical Design Features ...................................................................... 2  
Installation Considerations ...................................................................... 4  
Tools Needed .................................................................................... 4  
Placing the Punch Splits Speakers ...................................................... 4  
Installation .............................................................................................. 6  
Mounting the Midrange ..................................................................... 6  
Flush Mounting the Tweeter .............................................................. 7  
Surface Mounting the Tweeter ........................................................... 7  
Mounting the Punch Splits Plates....................................................... 8  
Crossover Installation .............................................................................. 8  
Troubleshooting .................................................................................... 12  
Specifications ........................................................................................ 13  
Warranty Information ............................................................................ 14  
International Information ....................................................................... 15  
G E T T I N G ST A R T E D  
Welcome to Rockford Fosgate! This manual is designed to provide  
information for owner, salesperson and installer. For those of you who  
want quick information on how to install this product, please turn to the  
Installation Section ofthismanualorreferto the iconslisted below. Other  
information can be located by using the Table of Contents. We, at  
Rockford Fosgate, have worked very hard to make sure all the information  
in this manual is current. But, as we are constantly finding new ways to  
improve our product, this information is subject to change without notice.  
I
N
S
T
A
L
L
A
T
I
®
®
TROUBLE-  
S
H
O
O
T
I
N
G
O
N
Sections marked  
INSTALLATION  
Sections marked  
TROUBLESHOOTING  
include “slam dunk”  
assembly and wiring connections  
include recommendations for  
curing installation problems  
PACKAGE CO NTENTS  
PCH-14x  
PCH-314  
(1) Installation & Operation Manual  
(2) 3/4" Tweeter  
(1) Installation & Operation Manual  
(2) 3/4" Tweeter  
(2) TX-4186 Crossover  
(2) Surface Mount Base  
(2) Surface Mount Cup  
(2) Flush Mount Base  
(2) Flush Mount Cup  
(2) 3" Midrange Speaker  
(2) 4x6 Mounting Plate  
(2) TX-4186 Crossover  
(2) 100µf Capacitor  
(2) Surface Mount Base  
(2) Surface Mount Cup  
(2) Flush Mount Base  
(2) Flush Mount Cup  
(8) #8 x 1.24 Screw  
PCH-414/PCH-514 or PCH-614  
(1) Installation & Operation Manual  
(2) 3/4" Tweeter  
(2) 4", 5" or 6" Midrange Speaker  
(2) PCH-142x Crossover  
(2) Speaker Grille Ring  
(2) Speaker Grille Gasket  
(2) Surface Mount Base  
(2) Surface Mount Cup  
(2) Flush Mount Base  
(2) Flush Mount Cup  
(8) #8 x 1.24 Screw  
(2) 15' 22 gauge Speaker Wire  
IN TRO D U C TIO N  
In today’s vehicles, space for everything is at a premium. Many times, the  
space that car designers dedicate for the stereo system is an afterthought.  
Rockford Fosgate realizes that people who want stereo systems in their  
vehicles have to contend with these real world problems. Our solution is  
the Punch Splits High Definition Component Systems. Punch Splits  
speakers are designed to fit in factory locations of vehicles with little  
modification while providing the awesome sound quality people have  
come to expect from Rockford Fosgate.  
1 –  
TECHNICAL DESIGN FEATURES  
Midrange Features  
PVA Treated Cone  
The lightweight paper cones are treated with PVA (PolyVinyl Acetate) for  
environmental stability and increased rigidity. This treatment promotes  
smooth midrange performance and low frequency extension free of  
distortion.  
THE RESULT: Strong and lightweight high performance cones.  
Vented Pole Piece  
The vented pole piece by design, ensures proper ventilation to cool the  
voice coil and maintains lower operating temperatures. This increases the  
thermal power handling of the speaker.  
THE RESULT: Improves power handling by cooling the voice coil.  
High Temperature Voice Coil  
The voice coil used in the Punch Series is of a high temperature copper  
wire construction. The wire is wound in two layers on a black anodized  
aluminum voice coil former. The voice coil former dissipates heat away  
from the voice coil improving the speaker’s thermal stability and improv-  
ing the reliability of the speaker.  
THE RESULT: Improves reliability by dissipating generated heat.  
Nitrile Rubber Surround  
The nitrile material is resilient to temperature variations and provides a  
consistent support necessary for the linear motion of the speaker cone. In  
addition, the inherent damping capabilities eliminates the transmission of  
degrading sonic disturbances between the cone and the frame of the  
speaker greatly improving the clarity of the speaker’s midrange frequency  
response.  
THE RESULT: Improves speaker's frequency response.  
2 –  
Tweeter Features  
Neodymium Magnets  
The high ionic compound of neodymium enables a smaller tweeter  
magnet assembly to be used as opposed to the much larger ferrite magnets  
that are commonly used in speaker manufacturing.  
THE RESULT: An efficient magnet which allows smaller tweeter  
construction.  
Magnetic Fluid Cooling  
Magnetic fluid is a synthetic liquid consisting of microscopic magnetic  
particles. The fluid has four times the thermal conductivity as air which  
makes it an ideal cooling agent. Magnetic fluid is injected into the voice  
coil gap which helps dissipate heat generated by the voice coil.  
THE RESULT: A thermal conductor which allows increased power  
handling.  
Swivel Mount Design  
The tweeter is encapsulated in a variable swivel housing. This design  
allows direct dispersion of the tweeter in order to accommodate various  
mounting positions. The swivel mount design allows the tweeter to  
maximize its sonic potential.  
THE RESULT: Precise tweeter imaging regardless of mounting position.  
Crossover Features  
Adjustable Tweeter Level Matching  
The passive crossovers utilize a series power resistor for tweeter level  
matching. The factory set tweeter output level is 0dB, however can be  
reduced –3dB to create a smoother transition between the midrange and  
tweeter. The ability to level match allows the system to be custom “tuned”  
for a particular listener or setup.  
THE RESULT: Allows custom setup of tweeter output level.  
– 3 –  
Optical Compression Circuit  
The supplied passive crossovers utilize an optical compression circuit for  
tweeter protection. This protection circuit absorbs the destructive signal  
caused when the amplifier's output is clipped. This greatly increases the  
power handling capability and the reliability of the tweeter.  
THE RESULT: Increased tweeter reliability under harsh conditions.  
Passive Filter Bypass  
The TX-4186 utilizes an extra screw terminal on the crossover housing  
which allows the tweeters audio signal to “bypass” the internal passive  
filter. This feature allows an external active filter to be used while  
maintaining optical compression for tweeter reliability.  
THE RESULT: System flexibility with constant tweeter protection.  
INSTALLATION CONSIDERATIONS  
Since many of the Punch Splits speakers are designed for direct replace-  
ment in factory speaker locations, some of the following instructions will  
not apply. To maximize the performance in difficult or custom installa-  
tions, please see your Authorized Rockford Fosgate Dealer.  
Warning! Please read the entire Installation section before attempting the  
installation of your Punch Splits Speakers.  
Tools Needed  
The following is a list of some of the tools necessary for the installation of  
the Punch Splits speakers.  
Power Drill with assorted bits  
Volt Meter  
Wire Strippers  
Wire Crimpers  
Marking Pen  
Hole Saw Arbor  
Assorted Hole Saws  
(Midrange)  
Assorted Screwdrivers  
Tape Measure  
Hole Saw (114")  
(Tweeter)  
Placing the Punch Splits Speakers  
A solid front stage with a good image is one of the most difficult tasks to  
achieve in a vehicle. No car has the optimum listening environment. This  
makes proper sound staging very difficult to accomplish. Most speakers  
tend to be placed where they will fit easily, as opposed to where they can  
perform the best The mounting location of your Punch Splits speakers will  
have a great effect on the sound quality of your stereo system. The special  
care taken to place the Punch Splits speakers, will yield many hours of  
listeningenjoymentin return. Severalimportantrecommendationsshould  
be followed.  
– 4 –  
I
®
®
N
S
T
A
L
L
A
T
I
Place the speakers where they have  
a direct path to the listening area.  
When using the Punch Splits, there  
are two options for speaker place-  
ment between the midrange and  
tweeter. For the best integration be-  
tween the midrange and tweeter,  
the tweeter should be placed less  
than 2"from the midrange. (Figure 1)  
If you cannot place the tweeter less  
O
N
2" or less  
Figure 1  
than 2" from the midrange, then place the tweeter more than 7"  
from the midrange. Placing the tweeter 2"-7" from the midrange  
can cause destructive interference (frequency response prob-  
lems) which will affect the speakers ability to reproduce the  
frequency range around the crossover frequency of the Punch  
Splits system.  
Whenever possible, place the tweeter directly above or below  
the midrange as this maximizes the imaging (point source)  
capability of the Punch Splits speakers. (Figure 2)  
Figure 2-A  
Figure 2-B  
Soundradiatedfromapointsourcehasthemostoptimumstereo imaging  
because the separation ofthe acousticalcentersbetween the midrange  
and tweeter for each channel is at the optimum. Figure 2-Adescribes  
a horizontal speaker alignment. In a closed environment such as an  
automobile, horizontal speaker alignment can cause severe ampli-  
tude and phase differences which will degrade not only the imaging,  
but also the frequency response. This is due to the path length  
differences between the midrange and tweeter. Figure 2-B displays  
a vertical alignment between the midrange and tweeter. With a  
vertical alignment, the path length differences between the midrange  
and tweeter are reduced to a minimum. The result is a negligible  
difference in path lengths between the midrange and tweeter regard-  
less of the proximity of the listener to the speakers. Mounting the  
– 5 –  
I
®
®
N
S
T
A
L
L
A
T
I
Punch Splits speakers with minimum path length differences will  
ensure the best staging and imaging possible from your audio  
system.  
O
N
IN STALLAT I O N  
The mounting of the Punch Splits speakers and crossovers is just as  
important as choosing the location for the speakers. Improper installation  
will degrade the sound quality and reduce the reliability of the Punch  
Splits speakers. To maximize the performance of your speakers, the  
following criteria should be considered.  
After choosing possible locations for the speakers, it is important to  
make sure there is a flat area large enough for the speaker to mount.  
Warning !Failure to do this can cause damage to the speaker if the  
frame of the speaker is bent during the installation.  
Check to see that the location is deep enough for the speaker and  
the location does not interfere with the normal operation of the  
vehicle.  
When mounting the speakers in the door of a vehicle, special care  
should be taken to make sure the speaker/s do not interfere with  
either the window operation or the door opening and closing. (Be  
careful of the tension bar in the door.)  
When mounting the speakers on the rear deck of the vehicle,  
double checkthe operation ofthe rearhatch ortrunklid. Make sure  
the tension bars and other moving parts are not obstructed by the  
speakersinstallation.  
Refer to the Specifications section of the manual for the mounting depth  
and proper diameter hole to cut for the Punch Splits speakers.  
Mounting the Midrange  
1. Cut the proper size hole for the midrange/woofer.  
2. Place the mounting ring over the mounting hole and mark the location  
of the screw mounting holes.  
3. Remove the ring. Drill the holes for the screws using a 1/8" drill bit.  
4. Route the wire through the hole.  
– 6 –  
I
®
®
N
S
T
A
L
L
A
T
I
5. Place the mounting ring over the hole.  
6. Attach the wires and be sure to observe the proper speaker  
polarity. Keep the speaker wires away from sharp and  
moving objects.  
O
N
7. Place the speaker into the hole and screw the speaker into place.  
Be careful not to bend the speaker frame during this step.  
8. Press the speaker grille into the mounting ring.  
Flush Mounting the Tweeter  
1. Cut a 1-1/4" mounting hole.  
2. Route the wires through the mounting hole.  
3. Attach the wires and be sure to observe the proper speaker polarity.  
Keep the speaker wires away from sharp and moving objects.  
4. Snap the tweeter with the flush mount capsule into the hole.  
5. Angle the tweeter for best sonic performance.  
Surface Mounting the Tweeter  
Mounting  
Plate  
1. Place the mounting plate on the surface where the tweeter will be  
located. Marktwo (2)opposingmountingholesand the centerwire  
access hole.  
2. Remove the mounting plate and drill a 1/4" (6.4mm) hole for the  
speaker wire access. Drill two (2) 1/8" (3mm) holes for the  
mounting screws.,  
3. Route the wires through the mounting hole.  
4. Place the mounting plate in position by threading the speaker wires  
through the center hole. Mount the mounting plate with the  
provided mounting hardware.  
5. Attach the wires and be sure to observe the proper speaker polarity.  
Keep the speaker wires away from sharp and moving objects.  
6. Snap the tweeter onto the mounting plate.  
– 7 –  
I
®
®
N
S
T
A
L
L
A
T
I
Mounting the Punch Splits Plates  
O
N
1. Cut the proper size hole for the midrange/woofer and  
tweeter. The midrange/woofer hole should be slightly  
larger than the mounting plate woofer hole.  
2. Place the mounting plate over the mounting holes and mark the  
location of the screw mounting holes.  
3. Remove the ring. Drill the holes for the screws using a 1/8" drill bit.  
4. Mount the speaker plate.  
Be careful not to bend the mounting plate during this step.  
5. Route the wires through the holes.  
6 Attach the wires and be sure to observe the proper speaker polarity.  
Keep the speaker wires away from sharp and moving objects.  
7. Place the speaker into the hole and snap the speakers into place.  
Note: Follow Steps 4 & 5 of Flush Mount Tweeter for tweeter.  
CRO SSO VER INSTALLATIO N  
Wiring the PCH-142x  
®
®
ACTIVE TWEETER PROTECTION  
PCH-142x  
®
Striped  
Wire  
+
+
+
Output from  
Amplifier  
Striped Wire indicates “+” terminal of tweeter  
– 8 –  
I
®
®
N
S
T
A
L
L
A
T
I
Wiring the PCH-314  
O
N
®
®
®
ACTIVE TWEETER PROTECTION  
TX-4186  
(Rear View)  
PCH-14  
+
+
+
Dot indicates  
“+” Terminal  
Input  
Protection  
Striped Wire  
(Rear View)  
PCH-34  
Dot indicates  
“+” Terminal  
+
Output from  
Amplifier  
100µf  
capacitor  
– 9 –  
I
®
®
N
S
T
A
L
L
A
T
I
Wiring the TX-4186  
(Crossover/Tweeter Protection)  
O
N
TWEETER  
PROTECTION  
CROSSOVER  
®
+
+
Tweeter  
Output  
Input  
Protection  
Input  
+
OUTPUT  
FROM  
AMPLIFIER  
+
Striped Wire indicates “+” terminal of tweeter  
Wiring the TX-4186  
(Tweeter Protection Only)  
TWEETER  
PROTECTION  
®
+
+
Input  
Protection  
Tweeter  
Output  
Input  
+
OUTPUT  
FROM  
AMPLIFIER  
+
Striped Wire indicates “+” terminal of tweeter  
WARNING: Use an external high-pass filter of at least 6kHz  
@ 18dB when configuring crossover for Tweeter Protection  
Only Mode  
– 10 –  
I
®
N
S
T
A
L
L
A
T
I
Tweeter Level Matching  
O
N
(Bottom view of PCH-142x/TX-4186  
Cut jumper  
wire for –3dB  
Factory set tweeter level is 0dB  
Cut jumper wire on bottom of crossover to reduce  
tweeter level by –3dB  
Horizontal Logo Mounting  
®
®
T X - 4 1 8 6  
A C T I V E T W E E T E R P R O T E C T I O N  
®
ACTIVE TWEETER PROTECTION  
TX-4186  
®
®
®
Configure logo into desired position and snap into place  
Vertical Logo Mounting  
®
®
Configure logo into desired position and snap into place  
– 11 –  
TROUBLE-S  
H
O
O
T
I
N
G
TR O U BL E SH O O T I N G  
Symptom  
Diagnosis  
Remedy  
No sound from  
speakers  
Check and repair or  
replace wiring as needed.  
Wires between amplifier,  
crossover and speakers  
not connected properly.  
Check system with known  
working amplifier and re-  
pair or replace as needed.  
Amplifier has no output.  
Check for shorts in the  
wiring with a volt/ohm  
meter and repair or  
Speaker wires are  
shorted to each other or  
to the chassis of the  
vehicle.  
replaced wires as needed.  
Check system with known  
working speaker and repair  
or replace as needed.  
Speakers are blown.  
Tweeters “burn  
up” easily  
Crossover is in “passive fil-  
ter bypass” configuration.  
Check wiring and re-config-  
ure as needed.  
External crossover is not fil-  
tering the tweeter properly.  
Check configuration of ex-  
ternal crossover and re-con-  
figure for at least 6kHz @  
18dB/octave  
Excessive clipping from  
amplifier.  
Check gain settings on am-  
plifier and readjust as  
needed.  
Equalizerin system (ifavail-  
able) has excessive boost in  
the high frequency range.  
Check settings on equalizer  
and readjust as needed.  
Distorted sound  
from speakers  
Incorrect wiring between  
crossover and speakers  
Check wiring and repair  
or replace as needed.  
Speaker wires shorted  
to chassis of vehicle.  
Check for shorts in the wir-  
ing with a volt/ohm meter  
and repair or replace wires  
as needed.  
Engine Noise  
from One  
or More  
Speakers  
Crossover ismounted near  
radiated noise source.  
(Powercables, computers,  
etc.)  
Move crossovers away from  
noise sources. (Refer to In-  
stallation section of manual  
on crossovers.)  
– 12 –  
– 13 –  
LIMITED W AR R AN T Y I N FO R M AT I O N  
Rockford Corporation offers a limited warranty on Rockford Fosgate products on the  
following terms:  
Length of Warranty  
1 year on speakers  
30 days on speaker B-stock (receipt required)  
90 days on electronic B-stock (receipt required)  
3 years on electronics  
2 years on source units  
What is Covered  
This warranty applies only to Rockford Fosgate products sold to consumers by  
Authorized Rockford Fosgate Dealers in the United States of America or its  
possessions. Product purchased by consumers from an Authorized Rockford  
Fosgate Dealer in another country are covered only by that countrys Distributor  
and not by Rockford Corporation.  
Who is Covered  
This warranty covers only the original purchaser of Rockford product purchased  
from an Authorized Rockford Fosgate Dealer in the United States. In order to  
receive service, the purchaser must provide Rockford with a copy of the receipt  
stating the customer name, dealer name, product purchased and date of purchase.  
Products found to be defective during the warranty period will be repaired or  
replaced (with a product deemed to be equivalent) at Rockford's discretion.  
What is Not Covered  
1. Damage caused by accident, abuse, improper operations, water, theft  
2. Any cost or expense related to the removal or reinstallation of product  
3. Service performed by anyone other than Rockford or an Authorized Rockford  
Fosgate Service Center  
4. Any product which has had the serial number defaced, altered, or removed  
5. Subsequent damage to other components  
6. Any product purchased outside the U.S.  
7. Any product not purchased from an Authorized Rockford Fosgate Dealer  
Limit on Implied Warranties  
Any implied warranties including warranties of fitness for use and merchantability  
are limited in duration to the period of the express warranty set forth above. Some  
states do not allow limitations on the length of an implied warranty, so this  
limitation may not apply. No person is authorized to assume for Rockford Fosgate  
any other liability in connection with the sale of the product.  
How to Obtain Service  
Please call 1-800-669-9899 for Rockford Customer Service. You must obtain an  
RA# (Return Authorization number)to return anyproductto Rockford Fosgate. You  
are responsible for shipment of product to Rockford.  
Ship to: Speakers  
Ship to: Electronics  
Rockford Corporation  
Warranty Repair Department  
2055 E. 5th Street  
Rockford Acoustic Design  
(Receiving-speakers)  
609 Myrtle N.W.  
Grand Rapids, MI 49504  
RA#:_________________  
Tempe, AZ 85281  
RA#:_________________  
– 14 –  
– 15 –  
Asegurese de leer las instrucciones antes de instalar estos productos.  
INTRODUCCIÓN  
En los vehiculos de hoy en dia, premia el espacio para todo. Muchas  
veces, el espacio que los diseñadores de coches dedican al equipo de  
música es un requerimiento posterior al diseño. Rockford Fosgate sabe  
que la gente que quiere equipos de música en sus vehiculos, debe pelear  
con este problema cotidiano. Nuestra solución es los sistema de  
componentes de Alta definicíon Punch Split. Los altavoces Punch Split  
están diseñados para ser situados en los lugares dispuestos por la fábrica  
de los vehiculos con sólo una ligera modificación, ofreciendo la calidad  
de sonido que la gente espera de Rockford Fosgate.  
LUGAR DE MONTAJE  
Para obtener una buena integración  
entre el altavoz de medios y el tweeter,  
el tweeter debe estar situado a menos  
de dos pulgadas del altavoz. (Figura 1)  
no superior a 5cm  
Figura 1  
I
®
®
N
S
INSTALACIÓN  
T
A
L
L
A
T
I
O
N
Montaje del altavoz de medios  
1. Corte el agujero de tamaño exacto para el altavoz de medios o  
woofer.  
• Para el PCH-44, corte un agujero de 96,8mm de diámetro  
• Para el PCH-54, cortelo de 123,8mm  
• Para el PCH-64, cortelo de 144,5mm  
2. Coloque el aro de montaje sobre el agujero y marque la posición de  
los agujeros para los tornillos.  
3. Saque el aro de montaje, Perfore los agujeros para los tornillos de  
sujeción usando una broca de 1/8" (3mm).  
– 16 –  
4. Coloque el cable a través del agujero.  
5. Coloque el aro de montaje sobre el agujero.  
6. Conecte los cables al altavoz observando la polaridad del mismo.  
7. Coloque el altavoz en el agujero y atornillelo. Tenga cuidado en  
no doblar el soporte del altavoz durante este paso.  
8. Presione la reja del altavoz sobre el aro de montaje.  
Montaje empotrado del Tweeter  
1
1. Corte un agujero de 1 4" (32mm).  
2. Coloque los cables a través del agujero de montaje.  
3. Conecte los cables observando la polaridad del altavoz. Aleje los  
cables de objetos móbiles o punzantes.  
4. Encaje el tweeter con la capsula de montaje en el agujero.  
5. Oriente el tweeter hacia donde obtenga una mejor caracteristica  
del sonido.  
Montaje superficial del Tweeter  
Superficie  
de montaje  
1. Coloque la superficie de montaje donde se situará el tweeter.  
Marque dos agujeros opuestos y haga el agujero contral para el  
acceso del cable.  
2. Saque la superficie de montaje y perfore con una broca de 6.4mm  
para el acceso del cable. Perfore los agujeros para los tornillos con  
una broca de 3mm.  
3. Pase los cables a través de los agujeros.  
4. Coloque la superficie de montaje en la posición, pasando los  
cables por el agujero central.  
5. Conecte los cables y asegurese de observar la polaridad del  
altavoz. Aleje los cables de objetos móbiles o punzantes.  
6. Encaje el tweeter en la superficie de montaje.  
– 17 –  
Conectando el PCH-142x  
®
®
ACTIVE TWEETER PROTECTION  
PCH-142x  
®
El hilo  
marcado  
+
+
+
Salida del  
Amplificador  
El hilo marcado indica el “+” del tweeter  
Ajuste de Nivel del Tweeter  
(Vista inferior del PCH-142x/TX-4186)  
Corte el cable para  
obtener –3dB  
El ajuste de origen es –0dB  
Corte el hilo en la parte inferior del tweeter para una  
reduccion del nivel del tweeter de –3dB  
Conectando el TX-4186  
(Crossover/Proteccion de Tweeter)  
Protección del Tweeter  
Crossover  
®
El hilo  
marcado  
+
+
Tweeter  
Input Output  
Input  
+
Salida del  
Amplificador  
Protection  
+
El hilo marcado indica el “+” del tweeter  
– 18 –  
ATTENTION: Veuillez lire les instructions suivantes pour l'installation de ces  
produits.  
INTRODUCTION  
Dans les véhicules actuels, l'espace est primor dial. Dans beaucoup de  
cas, l'espace dédié au système audio par les fabricants d'automobiles se  
retrouve au second plan. Rockford Fosgate réalise que les gens qui  
veulentun système audio dansleurvoiture sontconfrontésà ce problème.  
Notre solution est le système voies séparées Punch Splits. Les haut-  
parleurs Splits sont conçus pour être installés dans les emplacements  
d'origine après une légère modification tout en reproduisant la qualité  
sonore que les gens attendent de Rockford Fosgate.  
EMPLACEMENT DE MONTAGE  
Pour bénéficier d'une harmonie maxi-  
mum entre le médium et l'aigu  
l'éloignement entre ces deux haut-  
parleurs devrait être de moins de 5cm  
entre les 2 châssis. (Figure 1)  
moins de 5cm  
Figure 1  
I
N
S
T
A
L
L
A
T
I
®
®
INSTALLATION  
O
N
Montage du haut-parleur médium  
1. Découper un trou adapté au haut-parleur médium/woofer.  
• Pour le PCH-44, le diamètre du trou est de 96,8mm  
• Pour le PCH-54, le diamètre du trou est de 123,8mm  
• Pour le PCH-64, le diamètre du trou est de 144,5mm  
2. Placer l'anneau de montage sur le trou et repérer l'emplacement des  
des vis.  
3. Retirer l'anneau. Percer les trous des vis en utilisant une mèche de  
3mm.  
– 19 –  
4. Faire passer les fils dans le trou central.  
5. Placer l'anneau de montage au-dessus du trou central.  
6. Connecter les fils au haut-parleur en respectant les polarités.  
Eloigner les fils de toute partie tranchante ou mobile du véhicule.  
7. Placer le haut-plarleur au-dessus du trou central. Visser le haut-  
parleur dans son emplacement. Faire attention a ne pas tordre le  
chassis du haut-parleur durant cette etape de montage.  
8. Mettre la grille dans l'anneau de montage.  
Montage encastré du tweeter  
1. Découper un trou de montage de 32mm.  
2. Faire passer le fil dans le trou de montage.  
3. Connecter les fils au haut-parleur en respectant les polarités.  
Eloigner les fils de toute partie tranchante ou mobile du véhicule.  
4. Clipser le tweeter avec la capsule d'encastrement dans le trou.  
5. Diriger le tweeter pour atteindre la meilleure qualité de sonore.  
Montage en surface du tweeter  
Plaque de  
Montage  
1. Placer la plaque de montage en surface la où le tweeter doit être  
installé. Marquer deux (2) trous de montage opposés et le trou  
central pour le fil.  
2. Enlever la plaque de montage et percer un trou de 6,4 mm pour le  
trou central du fil. Percer deux (2) trous de 3mm pour les visses de  
montage.  
3. Diriger les visses dans les trous de montage.  
4. Placer la plaque de montage en position en faisant passer les fils à  
travers du trou central.  
5. Connecter les fils au haut-parleur en respectant les polarités.  
Eloigner les fils de toute partie tranchante ou mobile du véhicule.  
6. Clipser le tweeter sur la plaque de montage.  
– 20 –  
Branchement du PCH-142x  
®
®
ACTIVE TWEETER PROTECTION  
PCH-142x  
Fil  
®
marqué  
+
+
+
Sortie de  
l'empli  
Le fil marqué indique la connexion “+” du tweeter  
Compensation du Niveau Aigu  
Vue d'en bas du PCH-142x/TX-4186  
Coupez le pontage au  
verso du filtre pour –3dB  
Le niveau de défaut est de –0dB  
Coupez le pontage au verso du filtre our atténuer  
l'aigu de 3dB.  
Branchement du TX-4186  
Filtre passe-haut / Protection du tweeter  
Filtre  
Protection du Tweeter  
®
+
+
Sortie du  
Tweeter  
Entrée  
Entrée  
+
Sortie de  
l'empli  
+
Protection  
Le fil marqué indique la connexion “+” du tweeter  
– 21 –  
Bitte lesen Sie diese Gebrauchsanleitung zuerst sorgfältig durch. Das kann  
Sie vor dem falschen Einsatz, Ausfallen oder sogar BeschädigungdesProduktes  
oder Ihres Fahrzeuges schützen.  
EINLEITUNG  
In Fahrzeugen unserer heutigen Zeit ist Platz oft sehr begrenzt. Oftmals  
sind die vom Werk vorgesehenen Plätze für Lautsprecher sehr  
unzureichend. Rockford Fosgate hat verstanden, daβ es für Viele, die eine  
Stereoanlage im Auto wollen ein groβes Problem ist. Die Lösung dafür ist  
dasPunch SplitsKomponenten-System. Punch SplitsLautsprecherwurden  
designed um in Originaleinbauplätzen Raum zu finden und dabei die  
gute Klangqualität zu liefern, die Sie von Rockford Fosgate gewöhnt sind.  
EINBAUORT  
Für die beste Integration zwischen  
Mittel- und Hochtöner sollte der  
Hochtöner niemals weiter wie 5 cm  
vom Mitteltöner entfernt sein.  
5 cm oder weniger  
Figure 1  
I
N
S
T
A
L
L
A
T
I
®
®
MONTAGE  
O
N
Montage des Mitteltöners  
1. Schneiden Sie die richtige Lochgröβe für den Mitteltöner/Woofer aus.  
• Für den PCH-44, ein 96,8mm Durchmesserloch  
• Für den PCH-54, ein 123,8mm Durchmesserloch  
• Für den PCH-64, ein 144,5mm Durchmesserloch  
2. Plazieren Sie den Montagering über dem vorgesehenen Ausschnitt  
und markieren Sie die Schraubenlöcher.  
3. EntfernenSiedenRingundbohrenSie dieLöcherfürdenMontageringvor.  
4. Führen Sie das Kabel durch das Loch.  
– 22 –  
5. Montieren Sie den Lautsprecherring.  
6. Schlieβen Sie den Lautsprecher an und achten Sie darauf, daβ die  
Polung stimmt.  
7. Plazieren Sie den Lautsprecher und schrauben Sie ihn fest. Bitte  
achten Sie darauf, daβ der Lautsprecherkorb sich beim  
Festschrauben nicht verzieht.  
8. Pressen Sie das Lautsprechergitter vorsichtig in den Montagering.  
Hochtöner-Einbaumontage  
1. Schneiden Sie ein 1-1/4" (32mm) Montageloch.  
2. Führen Sie die Lautsprecherkabel durch dieses Loch.  
3. Klemmen Sie die Lautsprecherkabel am Lautsprecher an. Achten Sie  
auf die Polung und das die Kabel an keiner scharfen Kante anliegen.  
4. Pressen Sie den Hochtönermitseinem Gehäuse in dasvorgesehene  
Loch.  
5. Drehen Sie den Hochtöner in die klangbeste Stellung.  
Hochtöner-Aufbaumontage  
Montageplatte  
1. Plazieren Sie die Montageplatte des Hochtöners auf die  
vorgesehene Stelle. Markieren Sie 2 Befestigungslöcher und 1  
Mittelloch für das Kabel.  
2. Entfernen Sie die Montageplatte und bohren Sie ein Mittelloch  
von 6,4 mm fürdasLautsprecherkabelsowie 2 Befestigungslöcher  
von 3 mm für die Schrauben.  
3. Führen Sie die Kabel durch das vorgesehene Loch.  
4. Plazieren Sie die Montageplatte, führen Sie die Lautsprecherkabel  
durch das Mittelloch und montieren Sie die Montageplatte.  
5. Klemmen Sie die Lautsprecherkabel am Lautsprecher an. Achten  
Sie auf die Polung und das die Kabel an keiner scharfen Kante  
anliegen.  
6. Pressen Sie den Hochtöner auf die Montageplatte.  
– 23 –  
Verkabelung des PCH-142x  
®
®
ACTIVE TWEETER PROTECTION  
PCH-142x  
das  
®
abisolierte  
Kabel  
+
+
+
Ausgang vom  
Verstärker  
das abisolierte Kabel zum “+” Terminal des Hochtöners  
Tweeter Level Matching  
(Vorderansicht)  
Trennen Sie die  
Kabelbrücke um  
–3dB zu erreichen  
• Werkseinstellung Hochtonpegel –0dB  
Durch Trennen der Kabelbrücke reduzieren Sie den Pegel  
des Hochtöners um –3dB  
Verkabelung des TX-4186  
(Frequenzweiche/Hochton Sicherung)  
Crossover  
Tweeter Protection  
®
Eingang  
Hochtonschutz  
+
+
Hochton  
Ausgang  
Input  
+
Ausgang vom  
Verstärker  
+
das abisolierte Kabel zum “+” Terminal des Hochtöners  
– 24 –  
Si prega di leggere le istruzioni prima di procedere all'installazione.  
INTRODUZIONE  
Negli autoveicoli di oggi non c'é molto spazio. Molte volte i progettisti di  
automobili si accorgono solo a vettura ultimata che mancano gli spazi per  
gli impianti stereo. Rockford Fosgate é conscia del fatto che la gente che  
vuole realizzare degli impianti stereo sulle properie autovetture deve  
affrontare questo problema. La soluzione che proponiamo consiste nel  
Punch Splits High Definition Component Systems. Gli altoparlanti Punch  
Splits sono ideati per essere installati, con piccole modifiche, negli spazi  
predisposti per gli impianti, riuscendo cosí a riprodurre la grandiosa  
qualitá del suono che la gente si aspetta da Rockford Fosgate.  
POSIZIONAMENTO  
Per ottenere la migliore integrazione  
tra tweeter e midrange vi suggeriamo  
di posizionare i due componenti a  
meno di 5 cm tra loro (fig. 1).  
meno di 5cm  
Figura 1  
I
N
S
T
A
L
L
A
T
I
®
INSTALLAZIONE  
O
N
Installazione del Midrange  
1. Praticate un foro adatto per il midrange/woofer  
• 96,8mm per PCH-44  
• 123,8mm per PCH-54  
• 144,5mm per PCH-64  
2. Posizionate l'anello della griglia sul foro e segnate la posizione delle viti.  
3. Togliete l'anello della griglia e forate il pannello con una punta da 3 mm.  
4. Fate passare il cavo attraverso il foro praticato per l'altoparlante.  
– 25 –  
5. Posizionate la griglia spora il foro dell'altoparlante.  
6. Collegate i cavi facendo attenzione alla corretta polaritá.  
7. Posizionate l'altoparlante nel foro ed avvitatelo. Assicuratevi di  
non piegare il cestello dell'altoparlante.  
8. Incastrate la griglia sull'anello di fissaggio.  
Installazione ad incasso del tweeter  
1. Praticate un foro da 32mm.  
2. Fate passare i cavi attraverso il buco.  
3. Collegate i cavi facendo attenzione alla corretta polaritá.  
4. Incastrate il tweeter con la flangia di montaggio nel foro.  
5. Angolate il tweeter per ottenere la miglior qualitá timbrica.  
Installazione a superficie del Tweeter  
Flangia di  
montaggio  
1. Posizionate la flangia sulla superficie dove il tweeter sará  
posizionato e segnate 2 fori diametralmente opposti ed uno al  
centro per farvi passare il cavo.  
2. Togliere la flangia e con una punta da 6,5 mm fare un foro per il  
cavo dell'altoparlante. Pratciare 2 fori da 3 mm per le viti.  
3. Far passare i cavi attraverso il foro praticato.  
4. Posizionare la flangia in posizione infilando icavidell'altoparlante  
attraverso ilforo centrale. Montare la flangia con le vitia dotazione.  
5. Collegate i cavi prestando attenzione alla corretta polaritá.  
Accertarsi che i cavi dell'altoparlante siano distanti da superfici  
affilate e parti in movimento.  
6. Incastrare il tweeter sulla flangia di montaggi.  
– 26 –  
Cablare il PCH-142x  
®
®
ACTIVE TWEETER PROTECTION  
PCH-142x  
®
Cavi  
spellati  
+
Uscita  
dell'amplificatore  
+
+
Il cavo spellato indica il positivo del tweeter  
Regolazione del livello di emissione del tweeter  
(Vista Posteriore del PCH-142x/TX-4186)  
Tagliare il  
ponticello per –3dB  
• Il livello preimpostato é –0dB  
Tagliare il ponticello accessibile dal foro sul retro del  
crossover per ottenere un'attenuazione del tweeter di –3dB  
Cablare il TX-4186  
(Crossover/Protezione del tweeter)  
Crossover  
Protezione del tweeter  
®
ingresso  
protezione  
il cavo  
spellato  
+
+
Ingresso  
uscita del tweeter  
+
+
Il cavo spellato indica il positivo del tweeter  
– 27 –  
NOTES  
M ADE IN THE USA  
This product is designed, developed and assembled in the USA by a dedicated  
group of American workers. The majority of the components used in the  
construction of this product are produced by American companies. However, due  
to the global nature of their manufacturing facilities and the loudspeaker parts  
industry in general, some parts may be manufactured in other countries.  
Rockford Fosgate  
Rockford Corporation  
546 South Rockford Drive  
Tempe, Arizona 85281 U.S.A.  
In U.S.A., (602) 967-3565  
In Europe, Fax (49) 4207-801250  
In Japan, Fax (81) 559-79-1265  
LIT9781  
11/96  

Panasonic CXDP610EUC User Manual
Panasonic CQ C9901W User Manual
Panasonic Camcorder AG HVX200A User Manual
Olympus 227465 User Manual
Nikon 805x56DCF User Manual
Newcon Optik NEWCON Night Vision BN5 User Manual
MB QUART ONYX ONX11500D User Manual
Kenwood Excelon KVT 815DVD User Manual
JVC LYT0332 001A User Manual
JVC LYT0261 001B User Manual