Roadmaster VRCD220S User Manual

VRCD220S  
CD/MP3/WMA Player,  
AM/FM Stereo Receiver with RDS,  
Auxiliary Input and Detachable Face  
VRCD220S English PROOF Manual.indd  
1
10/15/08 11:34:09 AM  
Precautions  
This unit will only play the following discs.  
Type of disc  
CD  
Label on the Disc  
Recorded Material  
Audio only  
Size of Disc  
12 cm  
MP3/WMA  
N/A  
Audio only  
12 cm  
• Do not attempt to modify the unit.  
• Modifying the unit will void the warranty.  
• Do not operate in extremely high or low tem-  
peratures. The temperature inside the vehicle  
should be between 32º F (0º C) and 100º F  
(37º C) before turning on your unit.  
Stop the vehicle before carrying out any oper-  
ation that could interfere with your driving.  
Care of Discs  
• Do not use CDs with labels or stickers  
attached. The label may leave a sticky resi-  
due when it begins to peel.  
• Handle the disc by its edge to keep the disc  
clean. Do not touch the disc’s surface.  
• Do not use a CD with paste or ink residue  
on it.  
• Clean the discs with an optional cleaning  
cloth. Wipe each disc from the center out.  
2
VRCD220S English PROOF Manual.indd  
3
10/15/08 11:34:12 AM  
Notes on Installation  
• Disconnect negative battery terminal before starting installation. Consult the vehicle’s  
owner’s manual for proper instruction.  
• The unit is designed for a 12 Volt DC negative ground operation system only. Before  
installing the unit, make sure your vehicle is a 12 Volt DC negative ground system.  
• Mark the polarity of the existing speaker wires before disconnecting the old unit.  
• Be sure to connect the color coded leads according to the diagram. Incorrect connec-  
tions may cause the unit to malfunction or damage the vehicle's electrical system.  
• Make sure all the connections are completely correct before turning on your unit.  
• When extending the ignition, memory backup or ground cable, use diameter of 0.75mm  
(AWG18) or more automotive grade cable to avoid wire deterioration or damage to the  
wire coating.  
• To prevent short circuit, never put or leave any metallic object inside the unit. If you  
smell or see smoke, turn off the power immediately and consult your dealer.  
• Insert the unit until it is firmly locked into mounting sleeve, otherwise it may fall out.  
Be careful not to drop or shock the unit, it may break or crack because it contains glass  
parts.  
• The unit is only designed for use with 4 speakers. Do not combine output for use with  
2 speakers. Do not ground negative speaker leads to the chassis ground.  
• Do not open the top or bottom cover and do not install the unit in a place where it  
is exposed to direct sunlight (including faceplate), high heat, humidity, moisture, or  
dust.  
• The faceplate is a precision piece of equipment that contains sensitive electronic com-  
ponents. Do not subject it to excessive shock.  
• When replacing the fuse(s), the replacement must be of the same amperage as shown  
on the fuse holder.  
• Do not block vents or heater panels. Blocking them will cause heat to build up inside  
and may result in fire.  
• After completing the installation and before operating the unit, reconnect the battery.  
Then press the (RES) button with a pointed object, such as a ball-point pen to set the  
unit to its initial status.  
• Do not touch the terminals of the faceplate or of the unit.  
• If you have difficulty installing this unit in your vehicle. Please contact your dealer.  
Remove the  
half sleeve  
E
A
3
VRCD220S English PROOF Manual.indd  
4
10/15/08 11:34:12 AM  
Before You Install  
Automotive audio equipment installations can be challenging at times, even to the most  
experienced of installation technicians. If you are not condent working with electrical  
wiring, removing and reinstalling interior panels, carpeting, dashboards or other compo-  
nents of your vehicle, please call our toll-free help line 1-800-445-1797 and our in-house  
technical service team will answer your installation questions. Contact the vehicle's  
manufacturer for vehicle specic instructions, or consider having the VRCD220S profes-  
sionally installed.  
IMPORTANT: Remove the two transport screws from the top of the unit before installing.  
1. Remove the Old Unit from the Dashboard  
B. Insert the keys supplied with the old unit  
into both sides of the unit as shown in  
figure below until they click. Pull to re-  
move the old unit from the dashboard.  
A. Remove the outer trim frame.  
DIN Front Mount  
DO NOT DISCONNECT WIRES AT THIS TIME!  
2. Mark Polarity of the Speaker Wires  
Marking the polarity of the speaker  
wires will make it easier to connect the  
existing speakers to the VRCD220S.  
Consult wiring diagram of existing head  
unit before disconnecting any wires. If a  
wiring diagram is not available contact  
the manufacturer.  
well as left or right, and front or rear.  
4. Double check that you marked the  
first speaker correctly by checking  
that the speaker wires are the same  
at the head unit.  
5. Repeat this procedure for all of the  
speakers.  
6. Mark the power, ground, and any  
1. While the old unit is playing, discon-  
nect the wires from one speaker.  
2. Take a length of masking tape and  
fold it around the wire so it forms a  
flag.  
other wires also.  
3. On the masking tape mark the polar-  
ity of the speaker wires (+ & - ), as  
4
VRCD220S English PROOF Manual.indd  
5
10/15/08 11:34:13 AM  
Installation  
DIN FRONT-MOUNT (Method A)  
After inserting the Mounting Sleeve  
into the dashboard, select tabs on  
top, bottom, and sides, then bend  
them to secure the mounting sleeve  
in the dash board.(Fig. 1)  
Fig. 1  
Follow the diagram in Fig. 2 for in-  
stalling the rear mounting strap to  
the head unit. The rear mounting  
strap will help keep the head unit  
from moving around inside the dash-  
board.  
1. Dashboard  
2. Nut (5mm)  
3. Spring washer  
4. Screw (5  
25mm)  
5. Screw  
x
6. Strap  
7. Plain washer  
Fig. 2  
Insert ngers into the groove in the front of frame to remove it.  
Insert the keys supplied with the unit in the  
grooves on both sides. The unit can be installed  
or removed from the dashboard using these  
keys.(Fig. 3)  
Fig. 3  
5
VRCD220S English PROOF Manual.indd  
6
10/15/08 11:34:14 AM  
Installation  
DIN REAR-MOUNT (Method B)  
Installation using the screw holes on both sides of the unit.  
1. Screw holes on the side of the unit.  
2. Screws. Use either truss screws (5 x  
8mm) or ush surface screws (4 x 8mm),  
depending on the shape of the screw  
holes in the bracket.  
3. Vehicle’s Factory Mounting Bracket  
4. Dashboard or Console  
5 Hook (Remove this part)  
Note: The mounting sleeve, outer trim  
ring, and the mounting strap are not used  
for this method of installation.  
PARTS  
2 Keys  
1 Hex Nut  
2 Lock Washers  
1 Sheet Metal Screw  
1 Metal Support Strap  
2 Flat Washers  
1 Mounting Bolt  
1 Faceplate Case  
1 Faceplate(not shown)  
6
VRCD220S English PROOF Manual.indd  
7
10/15/08 11:34:14 AM  
Installation  
WIRING CONNECTIONS  
GIVE US A CALL, WE'LL HELP YOU INSTALL.  
PLEASE DO NOT RETURN PRODUCT TO STORE.  
Visit us on the WEB  
For Information and Technical Assistance,  
Call Toll-Free in U.S.A. and Canada.  
1-800-445-1797  
7
VRCD220S English PROOF Manual.indd  
8
10/15/08 11:34:15 AM  
Location of the Controls  
1
2
3
4
5
6
7
8
21  
20  
19 18  
17  
16  
15  
14  
13  
12  
11 10  
9
1. Clock Button  
2. Mode Button  
3. Volume Up Button  
4. SEL Button  
14. Pre-set #5/Down 10  
15. Pre-set #4/Random  
16. Pre-set #3/Repeat  
17. Pre-set #2/Intro  
18. Pre-set #1/Pause/Play  
19. TA Button  
20. Volume Down Button  
21. AF Button  
22. Eject button  
5. PTY Button  
6. LCD for Track Number, Time, Radio  
Frequency, File Type, ID3, RDS, EQ  
7. Open Faceplate Button  
8. Next Track/Change Frequency/Fast Forward  
9. Previous Track/Change Frequency/Fast Reverse  
10. Band Button  
23. Reset button  
24. Americas/Europe Switch  
25. Disc Slot  
11. F/PS Button  
12. Power Button  
26. Red LED  
13. Pre-set #6/Up 10  
22  
23  
24  
25  
26  
To Remove the Faceplate  
1. Press the Open Button to open the faceplate.  
2. Tilt the faceplate down about half way and push the faceplate to the left, then pull the  
it towards you to remove it.  
8
VRCD220S English PROOF Manual.indd  
9
10/15/08 11:34:16 AM  
Basic Operation  
1. Turning the Unit On / Off  
9. DSP-Preset Equalizer Function  
Press any button to turn the unit on, 1. Press and hold the “SELbutton until  
WELCOME will be displayed on the LCD to you hear a beep.  
indicate it is ready for use. Press and hold 2. Press the “SELbutton to cycle through  
the POWER button to turn the unit off.  
the menu choices until you see DSP  
OFF. 3. Press the +/- buttons to cycle  
through the pre-set EQ settings.  
2. Mode Selection  
Press the MODE Button to cycle between  
AUX, RADIO and CD modes.  
DSP OFF  
POP M  
ROCK M  
FLAT M  
CLASS M  
3. Volume  
4. Leave the unit idle for the new setting to  
take effect.  
Use the VOL +/- Buttons to adjust the vol-  
ume level. The higher the VOL number, the  
higher the volume level.  
10. Loudness  
1. Press and hold the “SELButton until  
you hear a beep.  
2. Press the “SELButton until the display  
shows “LOUD OFF”.  
3. Use the +/- Buttons to select “LOUD  
ON” (Loudness effect ON) or “LOUD  
OFF” (Loudness effect OFF).  
4. Leave the unit idle for the new setting to  
take effect  
4. Bass  
Press the “SELButton until the display  
shows “BAS”. Use the VOL +/- Buttons to  
adjust. When DSP is ON, the Bass control  
is not available.  
5. Treble  
Press “SELButton until the display shows  
“TRE”. Use the VOL +/- Buttons to adjust.  
When DSP is ON, the treble control is not  
available.  
11. Preset Beep Sound Off  
1. Press and hold the “SELButton until  
you hear a beep.  
2. Press the “SELButton until the display  
shows “BEEP ON”.  
3. Use the +/- Buttons to select “BEEP  
ON” (beep sound on) or “BEEP OFF”  
(beep sound off).  
6. Balance  
Press “SELButton until the display shows  
“BAL”, then use the VOL +/- Button to  
adjust the balance between the left & right  
speakers.  
7. Fader  
Press “SELButton five times and the  
display shows “FAD”, then use the VOL +/-  
Button to adjust the balance between the  
front & rear speakers.  
4. Leave the unit idle for the new setting to  
take effect.  
12. Preset Volume Level  
You can set the default volume level for the  
unit when it is turned ON.  
1. Press and hold the “SELButton until  
you hear a beep.  
2. Press the “SELButton until the display  
shows “VOL LAST”.  
3. Press the +/- Buttons to enter “VOL ADJ “  
will be displayed.  
4. Press the “SELButton and “A- VOL 15”  
will be displayed. The number after A-  
VOL indicates the volume level the unit  
will default to the next time you turn the  
unit ON.  
8. Clock  
1. While listening to the radio, press the  
“CLK” button until the clock is dis-  
played  
2. Press and hold the “CLK” button until  
the time starts to flash  
3. Press the VOL + Button to adjust the  
hour  
4. Press the VOL – button to adjust the  
minutes  
5. Press the “CLK” button again or just  
leave the the unit idle for a few new set-  
tings to take effect.  
9
VRCD220S English PROOF Manual.indd 10  
10/15/08 11:34:18 AM  
Radio Operation  
5. Press the +/- Buttons to adjust the vol- There are six numbered preset buttons  
ume level.  
which can store and recall stations for each  
6. Leave the unit idle for the new setting to band. While listening to a radio station you  
take effect. The next time you turn the would like to save as a pre-set, press and  
unit ON, the volume will automatically hold one of the buttons numbered 1-6 until  
be adjusted to the sound level you set you hear a beep. The button you pressed  
here.  
is now the pre-set button for that station.  
Radio Frequency Selection  
4. Automatic Store/Preset Scan  
The default frequency setting is in your  
country mode. However if you want to  
change the frequency to Europe or USA,  
please follow the step below:  
1. Press the Open Button to open the  
faceplate.  
2. Tilt the faceplate down about half way  
and push the faceplate to the left.  
3. Pull the faceplate towards you to remove  
it.  
4. Below the faceplate you will see a switch  
with the letter “A” on the right side and  
the letter “E” on the left side.  
A
. Automatic Scan & Store  
While listening to the Radio, press and  
hold the F/PS Button. The receiver will  
automatically scan all of the frequencies of  
the band you are tuned to.  
After scanning the frequencies it will auto-  
matically store the strongest signals to the  
pre-set buttons.  
If there are any stations already saved to  
the pre-set buttons, they will be replaced  
by the Automatic Scan & Store function.  
B. Scan Saved Stations  
5. For use in the Americas slide the switch  
to the left or for use in Europe slide the  
switch to the right.  
Press the F/PS button once to perform the  
scanning functions. In FM mode, press  
the F/PS button and the stations in all 3  
FM bands will be scanned; press this but-  
ton in AM mode and scan all 2 AM Band  
Stations.  
1. Choose a Radio Band  
The unit comes with five bands for storing  
your favorite radio - three FM Bands (FM1,  
FM2, and FM3) and two AM Bands (AM1,  
and AM2) selects. Each of the five bands  
can store up to six preset stations, for a  
total of 30 preset memory stations. 18 FM  
Pre-sets and 12 AM Pre-sets.  
RDS Operation  
Enhanced Other Networks (EON)  
This unit is equipped with the latest tech-  
nology of EON control. EON control allows  
the receiver to monitor other stations for  
traffic announcements while you are lis-  
tening to the Radio or a CD. If there are  
any travel announcements on a nearby  
local station, then the receiver will tune to  
the station, turn up the volume, or inter-  
rupt the playback of the CD for the dura-  
tion of the announcement. At the end of  
the announcement the radio will return  
to its previous state ready for the next  
announcement.  
2. Manual Tune / Seek Function  
Manual Tune: Press the “|>>” Button to  
adjust the radio to a higher frequency or  
press the “<<|” Button to adjust the radio  
to a lower frequency.  
Seek Function : Press and hold the >>|  
Button for about 2 seconds, and the radio  
will search forward for the next strongest  
frequency, then stop.  
3. Press and hold the “|<<” Button for  
about 2 seconds, and the radio will search  
backward for the next strongest frequency,  
then stop.  
AF - Alternative Frequencies  
Press the AF button and the unit will choose  
the strongest FM signal for the selected  
3. Save Your Preset Stations  
10  
VRCD220S English PROOF Manual.indd 11  
10/15/08 11:34:18 AM  
RDS Operation  
station. This means you do not have to sound select button again so that the unit  
re-tune the radio when driving between will show “MASK DPI”.  
different transmitter coverage areas. When Press the “+/-” Buttons to toggle between  
AF is on, it means RDS information is “MASK DPI” and “MASK ALLmode. Then  
received; when AF is flashing, it means leave the unit idle for the new setting to  
RDS information is not yet received.  
take effect.  
TA - Travel Announcements  
During “MASK DPI” mode, the unit will  
Press the TA button and the unit will be mask only the “AF” which has differ-  
activated for reception of traffic announce- ent “PI”, this is the default mode; during  
ments from local radio stations.  
“MASK ALLmode, the unit will mask the  
To choose the TA mode, press the “SEL AF which has different PI and no RDS sig-  
Button for 2 seconds, the display will nal with high field strength.  
show “TA SEEK”. Press the “+/-” Buttons  
to choose between “TA SEEK” and “TA RETUNE S/L - SHORT/LONG  
ALARM”, after chooisng, please leave the This function is to set the initial duration  
unit idle for the new mode setting to take of automatic TA Search -- Press and  
effect. In “TA SEEK” mode, the unit will hold the “SELbutton until “TA SEEK” is  
seek for traffic announcement program shown on the LCD, then Press the “+/-”  
when “TA” is pressed; in “TA ALARM” Buttons to cycle through the menu selec-  
mode, no “TA/TP” is displayed and the tions until “RETUNE_S” is shown, use the  
alarm is turned off.  
VOL +/- button to choose “RETUNE_S” or  
“RETUNE_L”. The default is “RETUNE_S”.  
TP - Traffic Program  
The “TP” Function is used to allow the user  
to find only those stations that regularly  
broadcast traffic bulletins.  
PTY - Program Type  
This “PTY” function allow you to select the  
type of program you wish to listen to, and  
will search for a station broadcasting that  
type of program. Press the “PTY” button  
once to show the music type. Then press  
the 1-6 buttons to choose the different  
music types available.  
Press the “PTY” button twice to show Talk  
Show programing you can search for, then  
press a number button 1-6 to choose a  
different Talk Show type program. Each  
number button can display 3 Talk Show  
programs for you to choose.  
There are up to 31 pre-defined program  
types that allows users to find programing  
by genre.  
MASK DPI - MASK ALL  
Press the “SELButton for 2 seconds, the  
display will show “TA SEEK”. Press the  
11  
VRCD220S English PROOF Manual.indd 12  
10/15/08 11:34:18 AM  
CD Operation  
Press this button again to resume play-  
back.  
Electronic Skip Protection - 12 or 45  
seconds  
Electronic Skip Protection is ideal for driv-  
ing on rough roads. Press the “SELButton  
until the display will show “TA SEEK”. Then  
press the “SELButton to cycle through  
the menu until “ESP12” is displayed indi-  
cating that 12 seconds Electronic Skip  
Protection will be activated.  
With “ESP 12” on the display, use the VOL  
“+/-” Buttons to change the setting to “ESP  
45”, indicating that 45 seconds Electronic  
Skip Protection is activated. Leave the unit  
idle for the new setting to take effect.  
4. Scanning Tracks  
Press the No.2/INT Button to play the first  
10 seconds of each track. Press this but-  
ton again to resume playback.  
5. Repeat  
Press the No.3/RPT Button to repeat the  
same track continuously. “RPT ON” will  
appear on the display. Press this button  
again to stop repeating.  
6. Random  
Press the No.4/RDM Button to play all the  
tracks in random order. “RDM ON” will  
appear on the display. Press this button  
again to stop random play.  
1. Insert/Eject CD  
Insert a disc with MP3 into the CD slot with  
label side up. The disc will be automatically  
loaded into the unit, even when it is off or  
in radio mode. The word “MP3 DISC” will  
be displayed  
as the CD is loaded. The first file in the root  
folder will be played. As the file is playing  
“ROOT” will be displayed first, then the if  
there is any ID3 information that will be  
displayed as the file is playing. Press the  
EJECT Button to eject the disc from the  
slot. If the disc is not removed from the  
slot within 5 seconds, it will automatically  
be loaded into the slot again. When the  
disc is ejected and removed, the unit will  
automatically switch to radio mode.  
2. Selecting Tracks  
On the Head Unit, press the SEEK >>|  
Button to advance CD to the next track.  
Track numbers will be shown on the dis-  
play. Press and hold SEEK >>| to fast  
forward. Press the SEEK |<< Button to go  
to a previous track. Track numbers will be  
shown on the display. Press and hold the  
SEEK |<< Button to fast reverse. Disc will  
play normally when the SEEK >>| or SEEK  
|<< Button is released. On the Remote  
Control, use the |<< or >>| Buttons.  
3. Play/ Pause CD  
Press the No.1 Button to pause the CD.  
12  
VRCD220S English PROOF Manual.indd 13  
10/15/08 11:34:18 AM  
MP3 & WMA Disc Operation  
MP3 & WMA Disc Operation  
4. Play/ Pause CD  
On the Head Unit, press the No.1 Button  
Electronic Skip Protection-120 Seconds to pause the CD. Press this button again  
Electronic Skip Protection is ideal for to resume playback.  
driving on rough roads. Electronic Skip  
Protection for MP3 & WMA CDs is a default 5. Scanning Tracks  
feature. Please note that this feature sup- On the Head Unit, press the No.2/INT  
ports CDs with Songs encoded by 96Kb/s Button to play the first 10 seconds of each  
and 32000Hz.  
track. Press this button again to resume  
For songs encoded in higher quality, the playback.  
anti-shock duration will decrease propor-  
tionally to the file size.  
6. Repeat  
On the Head Unit, press the No.3/RPT  
1. Insert/Eject CD  
Button to repeat the same track continu-  
Insert a disc with MP3 into the CD slot with ously. “RPT ON” will appear on the display.  
label side up. The disc will be automatically Press this button again to stop repeating.  
loaded into the unit, even when it is off or  
in radio mode. The word “MP3 DISC” will 7. Random  
be displayed  
On the Head Unit, press the No.4/RDM  
as the CD is loaded. The first file in the root Button to play all the tracks in random  
folder will be played. As the file is playing order. “RDM ON” will appear on the dis-  
“ROOT” will be displayed first, then the if play. Press this button again to stop ran-  
there is any ID3 information that will be dom play.  
displayed as the file is playing. Press the  
“EJECT” Button to eject the disc from the 8. UP 10  
slot. If the disc is not removed from the Press the No.6/UP10 Button to advance  
slot within 5 seconds, it will automatically 10 track at a time.  
be loaded into the slot again. When the  
disc is ejected and removed, the unit will 9. DN 10  
automatically switch to radio mode.  
Press the No.5/DN10 Button to go back 10  
track at a time.  
2. Selecting Tracks  
On the Head Unit, press the “>>|” Button to Search Modes  
advance CD to the next track. Track num- There are 4 search modes to help find your  
bers will be shown on the display. Press favorite MP3 tracks. The search modes  
and hold the “>>|” Button to fast forward. only works with MP3 CDs, and do not work  
The disc will play normally when the “>>|” with any other type of CDs.  
Button is released. Press the “|<<” Button  
to go to a previous track. The track num- 1. Simple Track Search  
bers will be shown on the display. Press Press the SEEK |<< or >>| Button to go  
and hold the “|<<” Button to fast reverse. to the next track or previous track. Press  
Disc will play normally when the “|<<” the Number 5 button to go back 10 tracks  
Button is released. On the Remote Control at once or press the Number 6 button to  
the “|<<” or “>>|” Buttons operate the advance 10 tracks at once.  
same as on the Head Unit.  
2. Track Search  
Press the F/PS Button and the display will  
show “TRK SCH”. Press the SEL Button so  
13  
VRCD220S English PROOF Manual.indd 14  
10/15/08 11:34:19 AM  
MP3 & WMA Disc Operation  
that “TRK” will blink on the display.  
AUX IN cable. Use the volume control to  
Then use the VOL +/- Button to choose adjust volume.  
your desired track and press the SEL  
Button again to confirm the selection. The 2. RCA Output  
selected track will be searched for and The RCA Output Jack is on the back of the  
then played.  
unit. (Refer to Wiring Diagram) This output  
is for connecting amplifier, equalizer, or  
other audio component that requires a  
3. File Search  
Press the F/PS Button twice and the pre-amp out connection. (Red = Right,  
display will show “FILE SCH”. Press the White = Left)  
SEL Button to enter the root folder of the Follow the manufacturers instructions for  
disc. Use the VOL +/- Button to choose a the audio component that you are con-  
folder in the root folder, then press the SEL necting.  
Button to confirm. The selected folder will  
be opened.  
4. Character Search  
Maintenance  
Press the F/PS Button three times and Cleaning the Unit  
the display will show “CHAR SCH”. This Do not use any liquids to clean this unit.  
is for files by file names. Press the SEL Do not use petroleum distillates to clean  
Button and the first character will blink this unit. Use a clean, dry cloth to clean  
on the display. Use the VOL +/- Button to this unit.  
change the character. Press the SEL but-  
ton once to confirm the character entered Replacing the Fuse  
and advance to the next character. After Make sure the amperage matches the  
you have input the name, press and hold specified value when replacing the fuse(s).  
the SEL Button to confirm. The song near- If the fuse is bad, check the power connec-  
est alphabetically to the name input will be tion and replace the fuse with a new one. If  
found and then begin to play.  
the same problem occurs, this might indi-  
cate a malfunction within the unit.  
Warning  
AUX IN & RCA Output  
1. Auxiliary Input  
When replacing a fuse, do not use a fuse  
with a higher amperage rating than the  
fuse originally supplied to your unit, other-  
The Auxiliary Input RCA Jacks are on the wise damage will result to your unit.  
rear of the unit. To use the AUX IN feature  
you must use a RCA to 3.5mm cable.  
Insert the cable’s RCA plugs into the Red &  
White AUX IN jacks on the rear of the unit.  
Route the end of the cable with the 3.5mm  
jack to an area that is safe and convenient  
to the headphone jack of any external  
audio device such as walkman and disc-  
man. Press the “Mode” button to choose  
AUX. Connect any portable audio device  
such as a DVD player or VCD player to the  
14  
VRCD220S English PROOF Manual.indd 15  
10/15/08 11:34:19 AM  
Simple Troubleshooting Guide  
PROBLEM  
CAUSE/SOLUTION  
No Power  
Check wiring connections.  
Check and make sure the fuse is not blown.  
Replace with the proper rating/size fuse.  
Some errors occur in the LCD or  
nothing functions when buttons  
are pressed.  
Press the RESET Button.  
Unable to receive stations  
Check and make sure the antenna is con-  
nected properly.  
Poor radio reception  
Check and make sure the antenna is the  
correct length. Make sure the antenna  
is not broken. If the antenna is broken,  
replace it. The antenna is poorly ground-  
ed. Check and make sure the antenna is  
grounded at mounting location.  
CD’s cannot be loaded  
Songs keep skipping  
A CD is already loaded in the player. Eject CD.  
The CD is dirty or damaged.  
File information shows in LCD but  
will not play.  
Your le may be corrupt.  
Specications  
GENERAL  
Operating Power...................................................... 11 to 16 Volts DC, Negative Ground  
Total Maximum Power .......................................................................................140 Watts  
RMS Power ................................................................4x7 Watts at 4 Ohms 1% THD+N  
Output Wiring.......................................................Designed for using four speakers only  
RCA line out .......................................................................... low-level outputs - 1000MV  
Output Impedance...................................................... Compatible 4 to 8 Ohm Speakers  
Fuses................................................................................................... 1 amp and 10 amp  
Dimensions ...............................................................178mm(W) x 178mm(D) x 51mm (H)  
Weight ..................................................................................................................... 2.3 Kg  
CD PLAYER  
Signal / Noise Ratio ................................................................................................>60dB  
Frequency Response...................................................................................20 Hz~20KHz  
Channel Separation ................................................................................................>50dB  
D / A Converter .......................................................................................................... 1 Bit  
FM TUNER  
Tuning Range ...................................(USA) - 87.5 - 107.9MHz, (Europe) - 87.5 - 108 MHz  
FM Sensitivity.......................................................................................................... 12dBu  
Stereo Separation @ 1 Khz....................................................................................... 35dB  
AM TUNER  
Tuning Range......................(USA) -- 530-1710 KHz, (Europe) -- 522-1620 KHz  
Am Sensitivity .........................................................................................................30dBu  
15  
VRCD220S English PROOF Manual.indd 16  
10/15/08 11:34:19 AM  
Limited Warranty  
VIRTUAL REALITY SOUND LABS® products are designed and manufactured to provide a high level of trouble-  
free performance. VIRTUAL REALITY SOUND LABS warrants, to the original purchaser, that its products are  
free from defects in material and workmanship for 30 days from the date of original purchase, as part of our  
commitment to product excellence. VIRTUAL REALITY SOUND LABS and/or it’s afliates routinely improves  
the designs, materials or production methods of its existing products. Because it is impractical to publicize all  
changes in every product, we reserve the right to make such changes without notice.  
CONDITIONS OF WARRANTY:  
If during the 30 day warranty period your new product is found to be defective, VIRTUAL REALITY SOUND LABS  
will repair such defect, or replace the product, without charge for parts or labor subject to the following condi-  
tions:  
1. All repairs must be performed by VIRTUAL REALITY SOUND LABS and/or its afliates in Eatontown, New Jersey.  
2. The equipment must not have been altered or been damaged through negligence, accident, or improper opera-  
tion.  
3. The replacement of parts are exempted from this warranty when replacement is necessary due to normal wear and  
tear.  
4. All warranty claims must be accompanied by a copy of the sales receipt or bill of sale.  
5. Repair or replacement parts supplied by VIRTUAL REALITY SOUND LABS under this warranty are protected  
only for the unexpired portion of the original warranty.  
6. In the case of car stereos, this warranty does not extend to the elimination of car static or motor noise; cor-  
rection of antenna problems; costs incurred for the removal or reinstallation of the product; damage to tapes,  
speakers, accessories or car electrical systems.  
7. VIRTUAL REALITY SOUND LABS will not be responsible for any charge incurred for installation.  
OWNER’S RESPONSIBILITIES:  
VIRTUAL REALITY SOUND LABS will make every effort to provide warranty service within a reasonable period of time.  
SHOULD YOU HAVE ANY QUESTIONS ABOUT SERVICE RECEIVED, OR IF YOU WOULD LIKE ASSISTANCE IN  
OBTAINING SERVICE, PLEASE CALL TOLL FREE 1-800-445-1797, 8:30am - 4:30pm EST.  
In order to provide you with the proper warranty service, we request that you adhere to the following procedure:  
1. Include a copy of your sales receipt or bill of sale with your unit when it is returned for warranty service.  
2. If it is necessary to return your product for service, please return it securely packed, preferably in the original  
shipping carton, and freight and insurance prepaid to the following address: VIRTUAL REALITY SOUND LABS,  
Service Department, 41 James Way, Eatontown, New Jersey 07724.  
3. Please include a detailed explanation of the problem you are having.  
4. If your product is found by VIRTUAL REALITY SOUND LABS to have a defect in material or workmanship, within  
the warranty period, it will be repaired or replaced at no charge and returned to you prepaid. Where permitted by  
Iaw VIRTUAL REALITY SOUND LABS liability shall be limited to that set forth in this warranty. This warranty shall  
be the exclusive remedy of the purchaser.  
VIRTUAL REALITY SOUND LABS® makes no other warranty of any kind, expressed or implied; and all implied  
warranties, are hereby disclaimed by VIRTUAL REALITY SOUND LABS and excluded from this warranty, VIR-  
TUAL REALITY SOUND LABS and/or its afliates, the manufacturer, distributor and seller shall not be liable for  
any injury, loss or damage, incidental or consequential, arising out of the use or intended use of the product.  
VRCD220S English PROOF Manual.indd 17  
10/15/08 11:34:19 AM  
©2008 Intellectual Solutions Inc., All rights reserved. All designs, logos and images are the exclusive property of  
Intellectual Solutions Inc. and/or its afliates. US and Foreign patents pending. 072208 Printed in China 00000  
VRCD220S English PROOF Manual.indd 18  
10/15/08 11:34:19 AM  

Plantronics Bluetooth Headset 510S User Manual
Nortel Networks Calculator n0060597 User Manual
Midland Radio X TRA TALK LXT385 User Manual
Mazda 2009 CX 7 User Manual
Maxxsonics Car Amplifier P1 20001 User Manual
KitchenAid KFP750BW1 User Manual
Kenwood Car Stereo System TH 41E User Manual
JVC LVT2095 001A User Manual
JVC KD AHD69 User Manual
JVC JCV Everio High Definition Digital Camcorder GSTD1BUS User Manual