Ricoh G700SE User Manual
Camera User Guide  
The serial number of this product  
is given on the bottom face of the  
camera.  
Basic Operations  
If you are using the camera for the first time, read this section.  
This section provides a basic overview of how to turn on the camera, take  
pictures and play back pictures.  
Advanced Operations  
Read this section when you want to learn more about the different camera  
functions.  
This section provides more detailed information about the functions used to  
take pictures and play back pictures, as well as information on how to customize  
the camera settings, print pictures, and use the camera with a computer.  
The rechargeable battery needs to be charged before use. The battery is not  
charged at the time of purchase.  
Safety Precautions  
Warning Symbols  
Various symbols are used throughout this instruction manual and on the  
product to prevent physical harm to you or other people and damage to  
property. The symbols and their meanings are explained below.  
This symbol indicates matters that may lead to imminent risk of death or  
serious injury if ignored or incorrectly handled.  
Danger  
This symbol indicates matters that may lead to death or serious injury if  
ignored or incorrectly handled.  
Warning  
This symbol indicates matters that may lead to injury or physical damage if  
ignored or incorrectly handled.  
Caution  
Sample Warnings  
The symbol alerts you to actions that must be performed.  
The symbol alerts you to prohibited actions.  
The symbol may be combined with other symbols to indicate that a specific  
action is prohibited.  
●
Examples  
Do not touch  
Do not disassemble  
Observe the following precautions to ensure safe use of this equipment.  
Danger  
●
Do not attempt to disassemble, repair or alter the equipment yourself. The high-  
voltage circuitry in the equipment poses significant electrical hazard.  
●
Do not attempt to disassemble, alter or directly solder the battery.  
●
Do not put the battery in a fire, attempt to heat it, use it in a high temperature  
environment such as next to a fire or inside a car, or abandon it. Do not put it into  
water or the sea or allow it to get wet.  
●
Do not attempt to pierce, hit, compress, drop, or subject the battery to any other  
severe impact or force.  
●
Do not use a battery that is significantly damaged or deformed.  
2
Warning  
●
Turn off the power immediately in the event of abnormalities such as smoke  
or unusual odors being emitted. Remove the battery as soon as possible,  
being careful to avoid electric shocks or burns. If you are drawing power from a  
household electrical outlet, be sure to unplug the power cord from the outlet to  
avoid fire or electrical hazards. Discontinue use of the equipment immediately if it  
is malfunctioning. Contact the nearest service center at your earliest convenience.  
●
Turn off the power immediately if any metallic object, water, liquid or other  
foreign object gets into the camera. Remove the battery and memory card  
as soon as possible, being careful to avoid electric shocks or burns. If you are  
drawing power from a household electrical outlet, be sure to unplug the power  
cord from the outlet to avoid fire or electrical hazards. Discontinue use of the  
equipment immediately if it is malfunctioning. Contact the nearest service center  
at your earliest convenience.  
●
Avoid any contact with the liquid crystal inside the picture display, should the  
monitor be damaged. Follow the appropriate emergency measures below.  
• SKIN: If any of the liquid crystal gets on your skin, wipe it off and rinse the  
affected area thoroughly with water, then wash well with soap.  
• EYES: If it gets in your eyes, wash your eyes with clean water for at least 15  
minutes and seek medical advice immediately.  
• INGESTION: If any of the liquid crystal is ingested, rinse the mouth out thoroughly  
with water. Have the person drink a large amount of water and induce vomiting.  
Seek medical assistance immediately.  
●
Follow these precautions to prevent the battery from leaking, overheating,  
igniting or exploding.  
• Do not use a battery other than those specifically recommended for the  
equipment.  
• Do not carry or store together with metal objects such as ballpoint pens,  
necklaces, coins, hairpins, etc.  
• Do not put the battery into a microwave or high pressure container.  
• If leakage of battery fluid or a strange odor, color change, etc. is noticed during  
use or during charging, remove the battery from the camera or battery charger  
immediately and keep it away from fire.  
●
Please observe the following in order to prevent fire, electrical shock or cracking  
of the battery while charging.  
• Use only the indicated power supply voltage. Also avoid the use of multi-socket  
adapters and extension cords.  
• Do not damage, bundle or alter power cords. Also, do not place heavy objects on,  
stretch or bend power cords.  
• Do not connect or disconnect the power plug with wet hands. Always grip the  
plug section when disconnecting a power cord.  
• Do not cover equipment while charging.  
●
Keep the battery and SD memory card used in this equipment out of the reach  
of children to prevent accidental ingestion. Consumption is harmful to human  
beings. If swallowed, seek medical assistance immediately.  
3
●
●
Keep the equipment out of the reach of children.  
Do not touch the internal components of the equipment if they become  
exposed as a result of being dropped or damaged. The high-voltage circuitry in  
the equipment could lead to an electric shock. Remove the battery as soon as  
possible, being careful to avoid electric shocks or burns. Take the equipment to  
your nearest dealer or service center if it is damaged.  
●
When the camera is used in kitchens or in other locations where it will be  
exposed to steam or high levels of humidity, care should be taken to prevent  
moisture accumulating inside the device. Failure to observe this precaution could  
result in fire or electric shock.  
●
●
Do not use the equipment near flammable gases, gasoline, benzene, thinner or  
similar substances to avoid the risk of explosion, fire or burns.  
Do not use the equipment in locations where usage is restricted or prohibited as  
this may lead to disasters or accidents.  
●
●
Wipe off any dust that accumulates on the electrical plug as this may lead to fire.  
Use only the specified AC adapter in household electrical outlets. Other adapters  
pose the risk of fire, electric shock or injury.  
●
To avoid the risk of fire, electric shock or injury, do not use the battery charger or  
AC adapter with commercially available electronic transformers when traveling  
abroad.  
Observe the following precautions to ensure safe use of this unit.  
Caution  
●
Contact with fluid leaking from a battery can lead to burns. If part of your body  
comes in contact with a damaged battery, rinse the area with water immediately  
(Do not use soap).  
If a battery starts to leak, remove it immediately from the equipment and wipe  
the battery chamber thoroughly before replacing it with a new battery.  
●
Plug the power cords securely into the electrical outlets. Loose cords pose a fire  
hazard.  
●
Do not expose the interior of the camera to moisture or allow water to enter  
the camera when handling the device with wet hands. Failure to observe these  
precautions could result in electric shock.  
●
Do not fire the flash at drivers of vehicles, as this may cause the driver to lose  
control and result in a traffic accident.  
Safety Precautions When using optional products, carefully read the instructions provided  
for Accessories  
with the product before using that product.  
4
Using the Manuals  
The following two manuals are included with your G700SE.  
“Camera User Guide”(This booklet)  
This guide explains the usage and functions of the camera.  
It also explains how to install the provided software on your  
computer.  
“Software User Guide”(PDF file)  
The “Software User Guide”is available in the following folders  
on the provided CD-ROM.  
This guide explains how to download images from the  
camera to your computer.  
Each language has its own  
“Software User Guide”in the  
respective folder.  
To copy the User Guide onto your hard disk, copy the PDF file  
from the respective folder directly to your hard disk.  
“MediaBrowser”image viewing and editing software (for Windows only)  
is also included with the camera. For how to use MediaBrowser, see the  
displayed “Help”.  
For more information on MediaBrowser, contact the Customer Support  
Center below.  
North America (U.S.)  
Europe  
TEL: (Toll Free) +1-800-458-4029  
UK, Germany, France and Spain: TEL: (Toll Free) +800-1532-4865  
Other Countries:  
Asia  
China  
TEL: +44-1489-564-764  
TEL: +63-2-438-0090  
TEL: +86-21-5385-3786  
Business hours: 9:00 AM to 5:00 PM  
5
Contents  
Safety Precautions................................................................................................ 2  
Using the Manuals................................................................................................ 5  
Contents................................................................................................................... 6  
Basic Operations  
15  
Packing List ...........................................................................................................16  
Optional Accessories.................................................................................................................16  
How to Use the Mode Dial...............................................................................17  
Names of Parts.....................................................................................................18  
Picture Display .....................................................................................................20  
Getting Ready ......................................................................................................23  
About the Battery........................................................................................................................23  
About the SD Memory Card (available in stores) ....................................................24  
Charging the Rechargeable Battery (DB-65)..............................................................26  
Loading the Battery and SD Memory Card.................................................................27  
Turning the Power On/Off.....................................................................................................28  
Setting the Language, Date and Time ...........................................................................29  
Basic Shooting .....................................................................................................31  
Shooting in Auto Shooting Mode (Focus and Shoot)..........................................31  
Using the Zoom Function......................................................................................................33  
Shooting Close-Ups (Macro Shooting)..........................................................................34  
Using the Flash..............................................................................................................................35  
Using the Self-timer...................................................................................................................36  
Shooting in CALS Mode..........................................................................................................37  
Shooting with My Settings Mode.....................................................................................37  
Playing Back Images ..........................................................................................38  
Viewing Your Images.................................................................................................................38  
Thumbnail View............................................................................................................................38  
Enlarging Images.........................................................................................................................40  
Deleting Files........................................................................................................41  
Deleting a File or All Files........................................................................................................41  
Deleting Multiple Files..............................................................................................................42  
Changing the Display with the DISP. Button.............................................44  
Maximizing the Picture Display Brightness.................................................................46  
The Level Indicator (Electronic Level).............................................................................46  
About the Histogram Display..............................................................................................48  
6
Advanced Operations  
49  
ADJ. Button Functions  
Selecting Shooting Menu Options Assigned to the ADJ./MEMO Button....50  
Shifting the AE and AF Targets............................................................................................51  
50  
1
2
3
Taking Pictures in Scene Mode  
52  
Scene Mode Options .........................................................................................52  
Using Skew Correction Mode..............................................................................................54  
Shooting and Viewing Movies  
55  
Shooting Movies .................................................................................................55  
Playing Back Movies...........................................................................................56  
Memos  
57  
4
5
Adding Memos to New Photos..........................................................................................57  
Viewing Memos............................................................................................................................58  
Using Custom Help  
59  
Creating Custom Help.......................................................................................59  
Viewing Custom Help........................................................................................61  
7
Shooting Menu  
62  
6
Using the Menu ...................................................................................................62  
Shooting Menu Options...................................................................................63  
Density: Adjusting Contrast in Text Mode ....................................................................63  
Size: Choosing the Size of Photographs Taken in Text Mode ................................63  
Movie Size: Choosing a Frame Size for Movies...........................................................63  
Picture Quality/Size: Choosing Size and Compression Options for  
Photographs..........................................................................................................................63  
Focus: Choosing How the Camera Focuses..................................................................63  
Exposure Metering: Choosing How the Camera Sets Exposure .......................63  
Continuous Mode: Shooting a Series of Photos......................................................64  
Image Settings: Adjusting Contrast, Sharpness, Color, and Vividness.............64  
Auto Bracket: Varying Settings over a Series of Photographs.............................64  
Time Exposure: Creating Light Trails ..............................................................................64  
Interval Shooting: Interval Timer Photography ........................................................65  
Camera Shake Correction: Reducing Blur Caused by Camera Shake............65  
Date Imprint: Imprinting the Time and Date of Recording  
on Photographs....................................................................................................................65  
Exposure Compensation: Adjusting Exposure........................................................65  
White Balance: Adjusting Colors According to the Light Source ......................66  
ISO Setting: Controlling the Camera’s Sensitivity to Light.....................................66  
Edit Detection: Detecting Changes to Photos...........................................................66  
Restore Defaults: Restoring Default Shooting Menu Settings ...........................66  
Focus...................................................................................................................................................67  
Manual Focus (MF): Focusing Manually.......................................................................67  
Auto Bracket...................................................................................................................................68  
Auto Bracket: Varying Exposure over a Series of Photographs...........................68  
White Balance Bracket (WB-BKT): Creating Photographs with Varying  
White Balance .......................................................................................................................68  
Exposure Compensation ........................................................................................................69  
White Balance................................................................................................................................70  
Manual: Measuring White Balance...................................................................................71  
ISO Setting: ISO Sensitivity........................................................................................................71  
8
Playback Menu  
72  
7
Using the Menu ...................................................................................................72  
Playback Menu Options....................................................................................73  
Resize: Creating Small Copies of Images .......................................................................73  
Trim: Creating Cropped Copies ..........................................................................................73  
Contrast Correction: Creating Copies with Modified Brightness  
and Contrast ..........................................................................................................................73  
Skew Correction: Reducing the Effects of Perspective..........................................73  
Protect: Protecting Images from Accidental Deletion.............................................73  
Slide Show: Automatic Playback......................................................................................73  
Copy to Card from Internal Memory: Copying Pictures from Internal  
Memory to a Memory Card.............................................................................................73  
DPOF: Selecting Pictures for Printing..............................................................................73  
Recover File: Restoring Deleted Files..............................................................................74  
File Send: Wireless Upload...................................................................................................74  
Trim ......................................................................................................................................................75  
Contrast Correction....................................................................................................................77  
Skew Correction...........................................................................................................................78  
Protect................................................................................................................................................79  
DPOF ...................................................................................................................................................80  
Viewing Pictures on TV .....................................................................................81  
9
Setup Menu  
82  
8
Using the Menu ...................................................................................................82  
Setup Menu Options..........................................................................................83  
Format [Card]: Formatting Memory Cards...................................................................83  
Format [Internal Memory]: Formatting Internal Memory ..................................83  
LCD Brightness: Adjusting the Picture Display Brightness...................................83  
Reg. My Settings: Saving Camera Settings .................................................................83  
Stepped Zoom: Adjusting Zoom in Discrete Steps.................................................83  
ADJ Button Setting 1–4: Choosing Roles for the ADJ. Button...........................84  
AF Auxiliary Light: Assisting Autofocus........................................................................84  
Operation Sounds: Choosing the Sounds Made by the Camera......................84  
Volume Settings: Controlling Volume...........................................................................84  
LCD Confirmation Time: Displaying Photos After Shooting ..............................84  
Auto Power Off: Camera Power Saving........................................................................84  
Monitor Auto off Delay: Choosing the Monitor off Delay...................................84  
LCD Auto Dim: Picture Display Power Saving............................................................84  
Digital Zoom Image: Recording Photos Taken with Digital Zoom  
at Actual Size .........................................................................................................................85  
Level Setting: Adjusting Level Indicator Settings .....................................................85  
Grid Guide Display Options: Choosing a Framing Guide...................................85  
Shooting Info. Display Frame: Viewing Settings at a Glance............................85  
Auto Rotate: Rotating Pictures for Playback................................................................85  
Card Sequence No.: File Numbering Options...........................................................86  
Date Settings: Setting the Camera Clock.....................................................................86  
Language/N : Choosing a Language......................................................................86  
Video Out Mode: Choosing a Video Format...............................................................86  
CALS Pic Quality: Choosing Picture Quality and Size for CALS Mode.............87  
Start Date/Time: Displaying the Date at Startup......................................................87  
Choose/Change Password: Choosing a Camera Password...............................87  
Password Protection: Using a Password to Restrict Camera Access ...............87  
Password Validity Period: Choosing the Length of Time the Password  
Remains in Effect .................................................................................................................87  
Power Button Hold Options: Adjusting POWER Button Responsiveness ...87  
Reg. My Settings...........................................................................................................................88  
Digital Zoom Image...................................................................................................................89  
Choose/Change Password ....................................................................................................90  
Password Protection..................................................................................................................92  
Camera: Adding Password Protection to the Camera .............................................92  
Int. Memory: Adding Password Protection to Internal Memory........................92  
10  
SD WORM: Disabling Password Protection for SD WORM Cards........................93  
Menus: Adding Password Protection to the Menus.................................................93  
Camera Memo Menu  
94  
9
Using the Menu ...................................................................................................94  
Camera Memo Menu Options........................................................................95  
Camera Memo Mode: Choosing a Memo Mode....................................................95  
Memo Skip: Skipping Memo Combinations...............................................................95  
Mark Memo Added to Photos: Displaying Memos That Have Been Added  
to Photos.................................................................................................................................95  
Remove Memo Marking: Removing Marking from Memos That Have Been  
Added to Photos..................................................................................................................95  
Memo Warning: Displaying an Empty Description Warning ..............................95  
Display Memo at Startup: Displaying the Camera Memo Dialog  
at Startup.................................................................................................................................96  
Memo Increment: Incrementing Numerical Memo Descriptions....................96  
Camera Memo Imprint: Imprinting Memos on Photos.......................................96  
Camera Memo 1 Auto Delete: Automatically Deleting the First  
Description.............................................................................................................................96  
Barcode Type: Choosing a Barcode Type......................................................................97  
Barcode Mode: Choosing a Destination for Barcode Data...................................97  
Scan Time: Choosing a Barcode Scan Time .................................................................97  
11  
Expanded Settings Menu  
98  
10  
Using the Menu ...................................................................................................98  
Expanded Settings Menu Options................................................................99  
GPS Datum: Choosing a Geodetic System for GPS ..................................................99  
GPS Disp Mode: Choosing How GPS Data Are Displayed....................................99  
GPS Lock: Disabling GPS Updates....................................................................................99  
GPS Data Select: Choosing a GPS Device................................................................. 100  
GPS Track Time: Choosing How Long GPS Logs Are Stored ............................. 100  
Delete GPS Log: Deleting GPS Logs............................................................................ 100  
Compass Heading: Choosing How Compass Data Are Displayed................ 100  
Compass Calibration: Calibrating the Compass ................................................... 101  
GPS Data Imprint: Recording GPS Data..................................................................... 101  
UTC Data Imprint: Recording UTC Data.................................................................... 101  
Heading Data Imprint: Recording the Compass Heading ............................... 101  
Range Finder Mode: Range Information Handling............................................. 101  
Communication Mode: Choosing a Wireless Connection Method............. 102  
Import Communication Setting: Loading a Host List...................................... 102  
Send To: Choosing a Host ................................................................................................. 102  
Send Status: Choosing When to Select a Host........................................................ 102  
Simple Connection: Using Simple Connection..................................................... 102  
Bluetooth Pass Key: Entering a Bluetooth® Password ........................................ 103  
Bluetooth Search Count: Limiting the Devices Detected................................ 103  
Bluetooth Auto Conn: Automatic Bluetooth® Connection ............................. 103  
Bluetooth Serial: Listing Bluetooth® Devices .......................................................... 103  
Bluetooth Master/Slave: Connecting to Multiple Devices............................... 103  
Image File Size: Resizing Images During Transfer.................................................. 103  
Auto Delete: Deleting Images After Transfer ........................................................... 104  
Quick Send Mode: Uploading Photos as They Are Taken.................................. 104  
Bluetooth Profile: Choosing a Bluetooth® Profile.................................................. 104  
Custom Help: Enabling Custom Help......................................................................... 104  
Admin Pass Key: Choosing a Password for Custom Help .................................. 104  
Admin Mode [Regist]: Updating Custom Help..................................................... 104  
Admin Mode [Delete]: Deleting Custom Help...................................................... 104  
12  
Bluetooth®  
105  
11  
Bluetooth® Connections................................................................................ 105  
Entering a Password ............................................................................................................... 106  
Transferring Images During Playback (Bluetooth®)............................. 107  
Transferring Images During Shooting (Bluetooth®)............................ 108  
One-Touch Transfer................................................................................................................. 109  
Two-Touch Transfer ................................................................................................................. 110  
Auto Transfer................................................................................................................................ 111  
Wireless Networks  
112  
12  
Connecting to a Wireless Network ............................................................ 112  
Configuring the Host ............................................................................................................. 113  
Detailed Setups Tab Settings ............................................................................................ 116  
Configuring a G700SE-only FTP Server....................................................................... 120  
Uploading Images to the SR-10 Server....................................................................... 122  
Creating a Host List and Transferring It to the Camera ...................... 123  
Reading a Host List from a Memory Card ................................................................ 125  
Viewing and Editing the Host List.................................................................................. 127  
Simple Connections for Wireless LANs..................................................... 128  
Connecting Using [WPS Button].................................................................................... 129  
Connecting Using [WPS PIN]............................................................................................ 129  
Connecting Using [Scan]..................................................................................................... 130  
Transferring Images During Playback (Wireless LANs)....................... 131  
Transferring Images During Shooting (Wireless LANs)...................... 132  
One-Touch Transfer................................................................................................................. 133  
Two-Touch Transfer ................................................................................................................. 134  
Auto Transfer................................................................................................................................ 135  
GPS  
136  
13  
Connecting to a GPS Unit ............................................................................. 136  
The GP-1 GPS Unit (Available Separately).................................................................. 136  
Bluetooth®-equipped GPS Units..................................................................................... 137  
The GPS Data Display ..................................................................................... 139  
Recording GPS Data........................................................................................ 140  
Viewing GPS Data ............................................................................................ 141  
13  
Barcode Reader  
142  
14  
The BR-1 Barcode Reader.............................................................................. 142  
Direct Printing  
144  
15  
About the Direct Print Function ................................................................. 144  
Connecting the Camera to a Printer ......................................................... 144  
Printing Still Images........................................................................................ 145  
Printing One or All Still Images........................................................................................ 145  
Printing Several Still Images............................................................................................... 147  
Printing Reports......................................................................................................................... 148  
Copying Pictures to a Computer via USB  
149  
16  
For Windows ...................................................................................................... 149  
System Requirements for Using the Supplied CD-ROM.................................. 149  
CD-ROM Setup........................................................................................................................... 150  
Copying Pictures to Your Computer............................................................................. 155  
For Macintosh.................................................................................................... 157  
Copying Pictures to Your Computer............................................................................. 157  
Appendices  
159  
17  
Troubleshooting............................................................................................... 159  
Error Messages........................................................................................................................... 159  
Camera Troubleshooting..................................................................................................... 163  
Available Settings ............................................................................................ 169  
Specifications .................................................................................................... 171  
Number of Images That Can Be Stored.................................................... 174  
Defaults Settings/Functions Whose Defaults Are Restored  
When the Camera Is Turned Off............................................................. 176  
Using a Wide Conversion Lens.................................................................... 179  
Optional Filters.................................................................................................. 179  
Using the External Flash................................................................................ 180  
Using Your Camera Abroad .......................................................................... 181  
Cautions on Use................................................................................................ 182  
Care and Storage.............................................................................................. 184  
Warranty and Servicing ................................................................................. 186  
Index.................................................................................................................... 192  
14  
Basic  
Operations  
If you are using the camera  
for the first time, read this  
section.  
Packing List..........................................16  
How to Use the Mode Dial ...................17  
Names of Parts.....................................18  
Picture Display.....................................20  
Getting Ready......................................23  
Basic Shooting .....................................31  
Playing Back Images............................38  
Deleting Files .......................................41  
Changing the Display with the DISP.  
Button ............................................44  
Packing List  
Open the package and make sure all the items are included.  
* The actual appearance of items included may differ.  
• G700SE  
• Rechargeable Battery  
• Battery Charger  
The serial number of the camera  
is provided on the bottom face of  
the camera.  
• Accessory Shoe Cover  
• USB Cable (Mini B cable)  
• AV Cable  
• Neck Strap  
• Warranty  
• Camera User Guide  
• CD-ROM (G P.149)  
Optional Accessories  
• Rechargeable Battery (DB-65) • Soft Case (SC-700)  
Used to store your camera.  
• Wide Conversion Lens (DW-5)  
• Battery Charger (BJ-6)  
Note-------------------------------------------------------------------------------------  
Attaching the Neck Strap to the Camera  
Thread the small end of  
the strap through the strap  
eyelet on the camera and  
loop the ends as shown.  
• For the latest information on optional accessories, see the Ricoh website (http://  
16  
www.ricohpmmc.com/).  
How to Use the Mode Dial  
Set the mode dial to  
the desired mode  
before shooting still  
images or movies.  
Mode Dial Symbols and Descriptions  
Symbol  
Function  
CALS Mode  
Description  
Refer to  
P.37  
Quality and size are adjusted to  
produce photographs suitable for  
public works photography. Picture  
quality and size can be selected  
from six options using the [CALS  
Pic Quality] item in the setup menu  
(G P.87).  
V
Auto Shooting Mode Automatically sets the optimal  
aperture value and shutter speed  
P.31  
5
depending on the subject.  
T,  
U
My Settings Mode  
Scene Mode  
You can shoot using the settings  
registered in [Reg. My Settings].  
Optimize settings for the current  
subject or scene or shoot movies.  
P.37  
P.52  
W
17  
Names of Parts  
Camera  
Front View  
3
4
5
6
7
2
1
8
10  
Item Name  
9
Refer to  
1
2
3
4
5
6
7
8
9
AF Auxiliary Light  
Shutter Release Button  
Mode Dial  
POWER Button  
Accessory Shoe  
Speaker  
Strap Eyelet  
Flash  
P.84  
P.31  
P.17, 31, 37, 52  
P.28  
P.180  
P.56  
P.16  
P.35  
P.55  
—
Microphone  
10 Lens  
18  
Rear View  
2
3
4
5
1
12  
11  
10  
6
3
7
8
13  
9
16  
15  
17  
14  
Item Name  
Refer to  
1
2
3
Picture Display  
Auto Focus/Flash Lamp  
Strap Eyelet  
P.20  
P.32, 35  
P.16  
4
5
6
P.33, 38, 40  
P.33, 38, 40  
P.38  
z (Telephoto)/8 (Enlarged View) Button  
Z (Wide-angle)/9 (Thumbnail View) Button  
6 (Playback) Button  
7
8
MENU/OK Button  
DISP. Button  
P.62, 72, 82, 94  
P.40, 44  
9
P.34  
"/N (Macro) Button  
10  
11  
P.36, 41  
P.35  
D (Delete)/t (Self-timer) Button  
#/F (Flash) Button  
12 ADJ./MEMO Button  
13 Terminal Cover  
14 AV Output Terminal  
15 USB Terminal  
16 Tripod Screw Hole  
17 Battery/Card Cover  
P.50, 57  
P.81, 144, 155, 157  
P.81  
P.144, 155, 157  
—
P.27, 179  
19  
Picture Display  
Example of Picture Display when Shooting Pictures  
Still Image Mode  
5
1
2 3  
4
6 7  
8
9
21  
22  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
32  
33  
20  
25  
23
31  
24  
30  
+
26  
27  
28  
29  
Item Name  
Flash Mode  
Edit Detection  
Scene Mode/Multi-shot  
Shooting Mode Types  
My Settings Mode  
Refer to  
P.35  
P.6  
P.52, 64 20 Time Exposure  
P.17  
P.37  
Item Name  
18 Camera Shake Correction  
19 Battery Symbol  
Refer to  
P.65  
P.22  
P.64  
P.36  
1
2
3
4
5
6
21 Self-timer  
22 Macro Shooting  
23 Digital Zoom Magnification/ P.34, 89  
Auto Resize Zoom  
P.34  
Remaining Number of Still P.174  
Images  
7
8
9
Recording Destination  
Image Size  
Picture Quality  
P.25  
P.63  
P.63  
P.63  
P.70  
P.63  
P.64  
P.64  
P.48  
P.94  
P.65  
24 Zoom Bar  
25 Interval Shooting  
26 Aperture  
27 Shutter Speed  
28 Exposure Compensation  
29 ISO Setting  
30 Level Indicator  
31 AF Frame  
P.33  
P.65  
P.171  
P.171  
P.69  
P.71  
P.47  
P.31  
10 Focus Mode  
11 White Balance  
12 Exposure Metering  
13 Image Settings  
14 Auto Bracket  
15 Histogram  
32 Exposure Warning Indicator P.69  
33 Camera Shake Warning Symbol P.33, 65  
16 Memo indicator  
17 Date Imprint  
20  
Movie Mode  
34  
35  
/
36  
Item Name  
34 Recording Time  
Refer to  
P.174  
Item Name  
36 Movie Recording Indicator P.55  
Refer to  
35 Remaining Recording Time P.174  
Note-------------------------------------------------------------------------------------  
When the number of remaining shots is 10,000 or more, “9999”is displayed.  
Example of Picture Display During Playback  
Still Image Mode  
Movie Mode  
5
1
2
3
4
6
7
8
9
/
/
15  
16  
10  
11 12 13  
14  
Item Name  
File Number  
Refer to  
—
Item Name  
Picture Quality  
Refer to  
P.63  
1
2
3
4
5
6
7
9
Number of Playback Files  
Total Number of Files  
Mode Types  
Protect  
DPOF  
—
—
—
P.79  
P.80  
P.25  
10 Date at Shooting  
11 Memo indicator  
12 Aperture  
13 Shutter Speed  
14 Battery Symbol  
15 Recording Time or Lapsed  
Time  
P.30  
P.94  
P.171  
P.171  
P.22  
Playback Data Source  
—
8
Image Size  
P.63  
16 Indicator  
—
21  
Note-------------------------------------------------------------------------------------  
• The picture display may display messages to inform you of operational  
instructions or the camera’s status while in use.  
• Additional information can be viewed by pressing the DISP. button (G P.44).  
1
2
4
5
/
3
6
8
ISO 100  
F5.5  
1
/
60  
EV 0.7  
+
7
9
10  
28 mm  
11  
12  
14  
13  
Blue  
15  
Item Name  
Refer to  
—
Item Name  
Flash Mode  
10 Focal Length of the Zoom P.33  
11 Macro Shooting  
12 Focus Mode  
13 Auto Bracket  
14 Image Settings  
15 Memo indicator  
Refer to  
P.35  
1
2
3
4
5
6
7
8
Shooting Mode  
Continuous Mode  
Aperture  
Shutter Speed  
ISO Setting  
Exposure Compensation  
Exposure Metering  
White Balance  
9
P.64  
P.171  
P.171  
P.71  
P.69  
P.63  
P.70  
P.34  
P.63  
P.64  
P.64  
P.94  
Battery Level Indication  
A battery symbol appears at the lower right of the picture display to  
indicate the battery level. Recharge the battery before it is depleted.  
Battery Symbol  
Description  
Battery is sufficiently charged.  
Green  
Battery partially discharged. Recharging is recommended.  
Battery level is low. Recharge the battery.  
Orange  
Caution---------------------------------------------------------------------------------  
Depending on battery make and condition, the level of AAA NiMH batteries may  
not be shown correctly.  
22  
Getting Ready  
Turn the power on and get ready to shoot.  
Note-------------------------------------------------------------------------------------  
• Be sure the camera is off before removing the battery.  
• For information on how to turn the camera off, see P.29.  
About the Battery  
The G700SE can be used with the following batteries:  
• DB-65 rechargeable Li-ion batteries (supplied)  
• AAA Alkaline Batteries (available in stores)  
• AAA Nickel-Hydrogen Batteries (available in stores)  
Number of shots you can take ----------------------------------------------------  
• Approximate number of shots you can take on a single charge  
Battery Type  
Rechargeable Battery (DB-65)  
AAA Alkaline Batteries (available in stores)  
Number of Shots (Normal Mode)  
approx. 360  
approx. 40  
* When [LCD Auto Dim] (G P.84) is set to [On].  
• Based on CIPA standard (Temperature: 23 degrees Celsius, picture display on, 30  
seconds between shots, changing the zoom setting from telephoto to wide-  
angle or wide-angle to telephoto for each shot, 50% flash usage, turning the  
power off after each 10 shots).  
• The figure for the number of shots that can be taken with AAA alkaline batteries  
is based on measurements made with batteries manufactured by Panasonic.  
• If [Off] is selected for [LCD Auto Dim], up to 345 shots can be taken with DB-65  
batteries and up to 40 shots with AAA alkaline batteries.  
• Set the camera to synchro-monitor mode to increase the number of shots you  
can take (G P.44).  
• The number of shots is for reference only. If the camera is used for long periods  
of time for setting and playback, the shooting time (the number of shots)  
will decrease. If you intend to use the camera for a long period of time, we  
recommend carrying a spare battery.  
23  
Caution---------------------------------------------------------------------------------  
• The battery may become very hot immediately after operation. Turn the camera  
off and leave it to cool down sufficiently before removing the battery.  
• Please remove the battery if you are not going to use the camera for a long  
period of time.  
• When using a lithium-ion battery, use only the specified rechargeable lithium-  
ion battery (DB-65). Do not use any other battery.  
• DB-60 Li-ion batteries can not be used.  
• NiMH batteries are not charged at purchase; charge before use.  
• NiMH batteries may suffer a drop in performance immediately after purchase  
or following a month or more of disuse and may need to be recharged two or  
three times before they will hold a charge.  
• The battery life of alkaline batteries varies with make and the time elapsed since  
the date of manufacture. Capacity drops at low temperatures.  
• Manganese and Ni-Cd batteries can not be used.  
• The drain on the battery increases when a GPS unit or barcode reader is  
connected or pictures are uploaded via Bluetooth® or over a wireless LAN. Use a  
DB-65 or ready spare AAA batteries.  
About the SD Memory Card (available in stores)  
Pictures can be stored in the camera’s 103MB internal memory or on  
optional SD, SDHC, and SD WORM memory cards (hereafter referred to  
as “memory cards”).  
SD WORM cards ----------------------------------------------------------------------  
Data stored on SanDisk® SD™ WORM (Write Once Read Many) cards can not be  
deleted or modified. The following are not available with SD WORM cards:  
Deleting files  
Skew Correction  
Movie shooting  
Memos  
Continuous Mode  
Resize  
P.41  
P.54, 78 Trim  
Recover File  
P.74  
P.75  
P.77  
P.79  
P.80  
P.83  
P.55  
P.57  
P.64  
P.73  
P.73  
Contrast Correction  
Protect  
DPOF  
Format [Card]  
Copy to Card from Internal  
Memory  
• SD WORM cards can contain up to 510 folders, each holding a maximum of 510  
photographs.  
• Files can not be copied from a computer to an SD WORM card when the camera  
is connected via USB.  
24  
About Formatting -------------------------------------------------------------------  
Before using a memory card for the first time or after using a memory card  
in other devices, be sure to format it with this camera. Memory cards can be  
formatted using the [Format [Card]] item (G P.83) in the setup menu (G P.82).  
Where images are recorded -------------------------------------------------------  
When no SD memory card is loaded, the camera records images to the internal  
memory (t); when an SD memory card is loaded, it records images to the SD  
memory card (u).  
Where images are played back from --------------------------------------------  
When no SD memory card is loaded, the camera plays back from the internal  
memory (t). When an SD memory card is loaded, it plays back from the SD  
memory card (u).  
Caution---------------------------------------------------------------------------------  
• If an SD memory card is loaded, the camera does not record to the internal  
memory, even if the card is full.  
• Take care not to get the contacts of the card dirty.  
Write-protecting your images ----------------------------------------------------  
Move the write-protection switch on the SD memory card  
to LOCK to prevent your still images from being accidentally  
erased or the card from being formatted.  
Note that you cannot shoot images on a locked card because  
no data can be recorded to the card. Unlock the card before  
shooting. Although SD WORM cards do not have a write-  
protection switch, they can not be formatted, and data can not be deleted from  
SD WORM cards.  
Note-------------------------------------------------------------------------------------  
• The [Copy to Card from Internal Memory] item (G P.73) in the playback menu  
(G P.72) can be used to copy the pictures in internal memory to a memory  
card.  
• An SD/SDHC memory card with a Speed Class of 6 or better is recommended  
when recording movies with [x1280] selected for [Movie Size] (G P.63).  
25  
Charging the Rechargeable Battery (DB-65)  
DB-65 Li-ion batteries must be charged before use.  
Insert the battery into the battery charger, making sure that  
the rand smarkings on the battery match those on the  
battery charger.  
1
• The battery label should face up.  
Caution---------------------------------------------------------------------------------  
Be careful not to reverse the rand ssides.  
Plug the power cable into an outlet.  
• Use the battery charger (BJ-6) to recharge the battery.  
2
• Charging starts. Charging status is indicated by the charger lamp as  
shown in the table below. Once charging has finished, unplug the  
battery charger from the power outlet.  
Charger Lamp  
Lit  
Description  
Charging  
Off  
Charging complete  
Flashing  
The battery charger terminal may be soiled or the battery  
charger/battery may be faulty. Unplug the battery charger  
from the power outlet, and remove the battery.  
• The approximate time needed to recharge a fully-exhausted battery  
is shown below.  
Rechargeable Battery Charging Time  
DB-65  
Approx. 150 min. (25 °C)  
26  
Loading the Battery and SD Memory Card  
After recharging the rechargeable battery, load the battery and the SD  
memory card. Be sure the camera is off before removing the battery or  
the SD memory card.  
Turn the battery/card cover knob  
toward the M mark to open the  
1
cover.  
Insert the rechargeable battery and  
SD memory card.  
2
• Make sure the SD memory card is  
facing the right way and then push the  
card all the way in until it clicks.  
• When the rechargeable battery is  
loaded in place, it is locked with the  
hook shown in the figure.  
Logo side  
Loading the specified dry cell batteries  
(available in stores)  
• Insert the batteries in the direction  
shown.  
Close and knob the battery/card  
cover.  
3
• Close the battery/card cover and rotate  
the knob to the position opposite the  
M
icon.  
27  
Removing the Rechargeable Battery  
Turn the battery/card cover knob toward the M mark to open the  
cover. Release the hook that locks the rechargeable battery. The  
battery is ejected. Pull the battery out of the camera. Be careful not to  
drop the battery when removing it from the camera.  
Removing the Dry Cell Batteries  
Turn the battery/card cover knob toward the M mark to open the cover.  
The batteries will be ejected. Pull the batteries out of the camera. Be careful  
not to drop the dry cell batteries when removing them from the camera.  
Removing the SD Memory Card  
Turn the battery/card cover knob toward the M mark to open the  
cover. Push in the SD memory card and gently release to eject it. Pull  
the card out of the camera.  
Caution---------------------------------------------------------------------------------  
• To prevent moisture or dust from entering the camera, close the battery/card  
cover securely.  
• Before opening or closing the battery/card cover, choose a location free of  
water, sand, mud, and other foreign matter and remove any such matter as may  
be adhering to the camera.  
• Make sure that the rechargeable battery and SD memory card are facing the  
right way when inserted into the camera. Inserting the rechargeable battery  
or SD memory card in the wrong direction and forcing close the battery/card  
cover may damage the camera, rechargeable battery or SD memory card.  
Turning the Power On/Off  
Press the POWER button to turn the camera  
on or off.  
When the camera is turned on, a start-up  
sound plays and the picture display turns on.  
If the POWER button is pressed when the  
camera is on, the number of files recorded  
on that day is displayed, and then the  
camera turns off.  
28  
Note-------------------------------------------------------------------------------------  
• If you adjust the clock before turning the camera off, the camera will display the  
number of shots taken since the clock was set.  
• A zero is displayed if the clock is not set.  
Using the Camera in Playback Mode  
Pressing and holding the 6 (Playback)  
button turns on the camera in playback  
mode, allowing you to start playback at once.  
When the camera has been turned on with  
the 6 button, pressing the 6 button again  
switches playback mode to shooting mode.  
About Auto Power Off --------------------------------------------------------------  
• If the camera goes unused for a set period of time, it automatically turns itself  
off to save power (Auto Power Off).  
• The auto power off setting can be changed (G P.84).  
About Password Protection (G P.92) -----------------------------------------  
If the camera is password protected, you may be prompted for a password when the  
camera is turned on. To use the camera, enter the password as described on P.90.  
Setting the Language, Date and Time  
When the power is turned on for the first time, the language setting  
screen appears (for the picture display language). After setting the  
language, go on to the date/time setting (for printing the date and  
time on your photos).  
Setting the Language  
Press the !" buttons to select a  
language.  
1
• When the DISP. button is pressed, the  
language setting is canceled and the  
date/time setting screen appears.  
Press the MENU/OK button.  
• The display language is set, and the date/time setting screen appears.  
2
29  
Setting the Date and Time  
Press the !"#$ buttons to set the year, month, date, time  
and format.  
1
• Change the setting with !" and move  
the item with #$.  
• You can cancel the setting by pressing  
the DISP. button.  
Check the information on the screen and then press the  
MENU/OK button.  
• The confirmation screen appears.  
2
3
Press the MENU/OK button.  
• The date and time are set.  
• If the battery is low, a warning will be displayed. Use of a fully-  
charged battery is recommended; to clear the warning from the  
display, press MENU/OK.  
Note-------------------------------------------------------------------------------------  
• The language, date, and time can be changed at any time using the [Language/  
N
] and [Date Settings] items (G P.86) in the setup menu (G P.82).  
• The [Date Imprint] item (G P.65) in the shooting menu (G P.62) can be used  
to stamp photographs with the date and time of recording.  
• If the battery is removed for more than three days, the date and time settings  
will be lost. These settings must be made again.  
• To retain the date and time settings, load a battery with adequate remaining  
power for more than ten hours.  
30  
Basic Shooting  
Now you are ready.  
Shooting in Auto Shooting Mode (Focus and Shoot)  
Turn the mode dial to 5 to shoot with auto  
shooting mode.  
The shutter release button works in two steps.  
When you press the shutter release button halfway  
(Half-press), the auto-focus function is triggered to  
determine the focal distance. Next, press it all the way down (Full-  
press) to shoot.  
When your subject is not in the center of your composition, compose  
your photo after focusing (Focus Lock).  
Hold the camera with both hands and  
lightly press both elbows against your  
body.  
1
Put your finger on the shutter release  
button.  
2
Frame the picture with your subject in the AF frame in the  
center of the screen and press the shutter release button  
halfway.  
3
• The camera focuses on the subject and the exposure and white  
balance are fixed.  
• The focal distance is measured at a maximum of nine points. Green  
frames appear to indicate the positions that are in focus.  
31  
To take a picture with the subject in the foreground in focus  
against a background, half-press the shutter release button to  
focus on the subject, and then compose your shot.  
4
5
Subject to be focused  
Shooting range  
Gently press the shutter release button all the way.  
•
The still image you have taken appears momentarily on the picture  
display and is recorded to the internal memory or the SD memory card.  
Caution---------------------------------------------------------------------------------  
When you are shooting, be careful not to obstruct the lens or flash with your  
fingers, hair, or the strap.  
About Focusing-----------------------------------------------------------------------  
The frame in the center of the picture display and the auto focus/flash lamp  
indicate whether the subject is in or out of focus.  
Focus Status  
Frame Color  
White  
Green  
Auto Focus/Flash Lamp  
Off  
On (Green)  
Before focusing  
Subject in focus  
Subject not in focus  
Red (Flashing)  
Blinks (Green)  
It may be impossible to bring the following subjects into focus, or they may not  
be in focus even when the frame color is green.  
• Objects that lack contrast, such as the sky, a wall that is only one color, or the  
hood of a car.  
• Flat two-dimensional objects with only horizontal lines and no significant  
protrusions.  
• Quickly moving objects.  
• Things in poorly lit places.  
• Areas with strong backlighting, or reflections.  
• Things that flicker, such as fluorescent lights.  
• Point light sources, such as light bulbs, spotlights, or LEDs.  
When you want to shoot subjects like this, first focus on an object the same  
distance as your subject and then shoot.  
32  
Preventing Camera Shake ---------------------------------------------------------  
• Press the shutter release button gently to prevent camera shake.  
• If you move the camera when pressing the shutter release button, the still  
image might not come out clearly due to camera shake.  
Camera shake tends to occur in the following cases:  
- When shooting in a dark place without using the flash  
- When using the zoom function  
- When [Time Exposure] (G P.64) is selected in the shooting menu (G P.62)  
• When the J symbol appears on the picture display, this indicates that  
camera shake may occur. To prevent camera shake, try any of the following.  
- Selecting [On] for [Camera Shake Correction] (G P.65) in the shooting menu  
(G P.62)  
- Setting the flash to [Auto] or [Flash On] (G P. 3 5 )  
- Raising the ISO setting (G P.71)  
- Using the self-timer (G P.36)  
Using the Zoom Function  
Press the z (Telephoto) button to zoom in  
so that your subject fills more of the frame.  
To zoom out and increase the area visible  
in the frame, press the Z (Wide-angle)  
button.  
Wide-angle Telephoto  
Zoom bar  
Note-------------------------------------------------------------------------------------  
The [Stepped Zoom] option (G P.83) in the setup menu (G P.82)  
allows optical zoom to be adjusted in six discrete steps.  
33  
Using the Digital Zoom -------------------------------------------------------------  
Optical zoom offers magnifications of up to 5.0 ×; if desired, magnification can be  
further increased by up to 4.0 × using digital zoom. For digital zooming, release  
the z button once when the zoom reaches the limit on the z end on the  
zoom bar, and then hold the z button down again. If [l4 : 3 F] or [l4 : 3 N] is  
selected for [Picture Quality/Size], you can select [Auto Resize] for [Digital Zoom  
Image] (G P.89).  
Shooting Close-Ups (Macro Shooting)  
Use macro mode for close-ups. Press the N  
(macro button) to enable or disable macro  
mode.  
Note-------------------------------------------------------------------------------------  
• [Focus] (G P.63) is set to [Spot AF].  
• Macro mode is not available in manual focus mode (G P.63).  
• To take a further close-up picture during macro shooting, use [Zoom Macro]  
(G P.52) in scene mode.  
• The minimum shooting distance and shooting range when using the zoom are  
shown below.  
Zoom position Minimum Shooting Distance Shooting Range  
(from the front of the lens)  
Wide-angle  
Approx. 1 cm  
Approx. 15 cm  
Approx. 21.8 mm × 16.4 mm  
Approx. 42.3 mm × 31.7 mm  
(when digital zoom is not used)  
Approx. 10.6 mm × 7.9 mm  
(when 4.0× digital zoom is used)  
Telephoto  
Approx. 15 cm  
34  
Using the Flash  
You can select the flash mode that best suits your shot. At the time of  
purchase, the camera is set to [Flash Off].  
With the camera ready to shoot,  
press the F button.  
1
• The list of the flash modes symbol is  
displayed on the picture display.  
Flash Off  
Auto  
The flash will not fire.  
The flash fires automatically when the subject  
is poorly lit or backlit.  
Anti Red-Eye  
Flash On  
Reduces the red-eye phenomenon, in which  
people’s eyes appear red in pictures.  
The flash fires regardless of the lighting  
conditions.  
FLASH ON (10M) The flash always fires with a range of 10 m.  
When zoomed in on your subject, the flash  
fires with a range of 6.2 m.  
Flash Synchro.  
The flash fires with the shutter speed slowed.  
This is useful when taking portrait pictures in  
a nightscape. Camera shake may occur, so the  
use of a tripod is recommended.  
Press the !" buttons to select the flash mode.  
• The flash mode symbol is displayed at the upper left of the picture  
display.  
2
• The auto focus/flash lamp blinks while the flash charges. Photos can  
be taken when the lamp turns off.  
Caution---------------------------------------------------------------------------------  
• You cannot shoot when the flash is charging (approx. 8 seconds).  
• If the camera is powered by AAA alkaline or NiMH batteries, the picture display  
will turn off while the flash charges.  
• After the camera is turned on, it may take longer for the camera to become  
ready for shooting when using the flash.  
35  
Note-------------------------------------------------------------------------------------  
• The flash mode setting is retained until you press the F button again.  
• The auxiliary flash fires to increase the AE accuracy.  
• The flash can not be used in some shooting modes or with some shooting  
menu options (G P.169).  
Using the Self-timer  
The camera offers a ten-second timer for self-portraits and a two-  
second timer to prevent blur caused by camera movement when the  
shutter release button is pressed.  
With the camera ready to shoot, press the t (Self-timer)  
1
button.  
• The Self-timer symbol appears on the  
screen.  
• The [10] to the right of the symbol  
indicates the number of seconds. In this  
case, if you press the shutter release  
button, the camera will shoot after 10  
seconds.  
• Each press of the t button changes the self-timer setting in the  
following order: 10 sec, 2 sec, and Self-timer Off.  
Start the timer.  
• Press the shutter release button to lock focus and start the timer. If  
the ten-second timer is selected, the AF auxiliary light will light.  
2
Note-------------------------------------------------------------------------------------  
• The camera remains in self-timer mode even after the image is shot. To cancel  
the self-timer, press the t button and change the self-timer setting to [Self-  
Timer Off].  
• When the self-timer is set to 2 seconds, the AF auxiliary light does not blink.  
• When the self-timer is set, the [Interval Shooting] setting is disabled.  
36  
Shooting in CALS Mode  
In CALS mode, you can shoot photos in a quality  
and size suitable to be submitted as official public  
works pictures. Picture quality and size are set  
beforehand in [CALS Pic Quality] on the setup menu  
(G P.87). At shipment, [CALS Pic Quality] is set to  
[a4:3N] (normal image quality, 1280×960 pixels,  
with a file size of about 363KB) to conform to the Japanese standard  
for official public works photographs, which requires that images be  
1 megapixel with a file size of 500KB or less.  
Note-------------------------------------------------------------------------------------  
• When the mode dial is set to a mode other than CALS, [Picture Quality/size]  
returns to the setting in the previous mode.  
• You can register [CALS Pic Quality] as My Settings (G P.88).  
Shooting with My Settings Mode  
Rotate the mode dial to Tor Uto take  
photos using settings saved with the [Reg. My  
Settings] option in the setup menu (G P.88).  
Note-------------------------------------------------------------------------------------  
You can change the camera settings set in my settings mode. Changing the  
mode or turning the camera off returns the settings to the original MY1 and MY2  
settings.  
37  
Playing Back Images  
Viewing Your Images  
To select playback mode, press the 6  
(Playback) button. When the camera is off,  
pressing and holding the 6 (Playback)  
button longer than 1 second turns the  
camera on in playback mode.  
Press the #$ buttons to display the  
previous file or the next file. Press the !"  
buttons to display the file 10 frames forward or backward.  
To switch the camera from playback mode to shooting mode, press  
the 6 button again.  
Thumbnail View  
20 Frames  
Press the 9 (Thumbnail view) button to  
view pictures 20 at a time.  
Press the DISP. button to change between  
the thumbnail list and page list. In the page  
list, press the !"#$ buttons to select  
the page.  
To display the highlighted photo full frame,  
press the ADJ./MEMO or 8 (Enlarged view)  
button.  
38  
81 Frames  
To display pictures 81 at a time, press 9 in  
the 20-frame view.  
Press the DISP. button to change between  
the thumbnail list and page list. In the page  
list, press the !"#$ buttons to select  
the page.  
Thumbnail list  
To display the highlighted photo full frame,  
press the ADJ./MEMO button or press 8  
twice.  
Page list  
Date of Recording  
To switch to a calendar display, press 9 in  
the 81-frame view.  
Press the DISP. button to change between  
the thumbnail list and date list. In the date  
list, press the #$ buttons to select the  
date, or press the !" buttons to select  
the page.  
Thumbnail list  
To display the highlighted photo full frame,  
press the ADJ./MEMO button or press 8  
three times.  
Date list  
39  
Enlarging Images  
To zoom in on a photo that is currently displayed full frame, press the 8  
(Enlarged view) button. Maximum magnification varies with image size.  
Image Size  
Enlarged View (maximum magnification)  
z4 : 3 F  
a4 : 3 F/a4 : 3 N/b4 : 3 F  
3.4 ×  
6.7 ×  
Image sizes other than those above 16×  
Operations that can be performed in enlarged view  
8/9  
Zoom in or out. Press !, ", #, or $ to view other areas of the image.  
MENU/OK If the current magnification less than 8×, zoom in to 8× or to maximum  
magnification, whichever is less. If the current magnification is 8× or  
more, zoom in to 16×. If the picture is currently displayed at maximum  
magnification, pressing MENU/OK cancels zoom.  
Pressing the DISP. button at this point changes the display as follows.  
DISP. button  
Pressing the !"#$  
buttons at this point moves  
the area displayed.  
Pressing the !"#$  
buttons at this point moves  
the area displayed.  
Pressing and  
holding the  
DISP. Button  
Pressing and  
holding the  
DISP. Button  
Pressing the !"#$ buttons at this point  
displays the previous or next image enlarged.  
Note-------------------------------------------------------------------------------------  
• Movies cannot be enlarged.  
• Cropped copies (G P.75) can not be zoomed in to the magnifications stated  
above.  
40  
Deleting Files  
You can delete files from the SD memory card or internal memory.  
Note-------------------------------------------------------------------------------------  
• You can use the [Recover File] function to restore needed files that you  
accidentally deleted(G P.74). Note, however, that files can not be recovered  
if, for example, the camera has been turned off or shooting mode has been  
selected since the files were deleted.  
• Files can not be deleted from SD WORM memory cards.  
Deleting a File or All Files  
Press the 6 (Playback) button.  
• The last file recorded is displayed.  
1
Press the !"#$ buttons to display the file you want to  
delete.  
2
• To select multiple pictures, use the 9 (Thumbnail view) button to  
select a multi-frame view before proceeding to Step 3.  
Press the D (Delete) button.  
3
4
Press the !" buttons to select  
[Delete One] or [Delete All].  
• You can change the image for deletion  
with the #$buttons.  
Press the MENU/OK button.  
• If [Delete All] is selected, press the #$ buttons to select [Yes] and  
5
then press the MENU/OK button.  
41  
Deleting Multiple Files  
You can select multiple files for simultaneous deletion either  
individually or by selecting one or more ranges consisting of two  
images and all photographs between them. To delete multiple files,  
press the D (Delete) button in playback mode and follow the steps  
below (to exit at any time without deleting images, press DISP.).  
Specifying Multiple Files Separately  
Press the !" buttons to select [Delete Multi] and then  
press the MENU/OK button.  
1
• Omit this step if the camera is already in multi-frame view.  
Press the !" buttons to select [Sel. Indiv.] and then press  
the MENU/OK button.  
2
Press the !"#$ buttons to select  
the file you want to delete and  
press the MENU/OK button.  
3
• The trash symbol is displayed in the  
upper left corner of the file.  
• Press the ADJ./MEMO button to switch  
to the display for specifying a range of  
files. See Step 3 and beyond on P.43.  
Repeat Step 3 to select all the files you want to delete.  
• If you selected a file by mistake, you can deselect it by selecting the  
file and pressing the MENU/OK button.  
4
• Press DISP. to cancel and return to Step 2.  
Press the D (Delete) button.  
5
6
Press the #$ buttons to select [Yes] and then press the  
MENU/OK button.  
42  
Specifying a Range of Multiple Files  
Press the !" buttons to select [Delete Multi] and then  
press the MENU/OK button.  
1
• Omit this step if the camera is already in multi-frame view.  
Press the !" buttons to select [Sel. Range] and then press  
the MENU/OK button.  
2
3
/
Press the !"#$ buttons to select  
the starting point of the range of  
files you want to delete and press  
the MENU/OK button.  
• If you make a mistake when selecting  
the starting point for the range of files,  
press the DISP. button to return to the  
screen for selecting the starting point.  
• Press the ADJ./MEMO button to switch to the display for specifying  
files separately. See Step 3 and beyond on P.42.  
/
Press the !"#$ buttons to select  
the ending point of the range of  
files you want to delete and press  
the MENU/OK button.  
• The trash symbol is displayed in the  
upper left corner of the specified files.  
4
5
• Press DISP. to cancel and return to  
Step 2.  
Repeat Steps 3 and 4 to specify all the ranges of files you  
want to delete.  
Press the D (Delete) button.  
6
7
Press the #$ buttons to select [Yes] and then press the  
MENU/OK button.  
43  
Changing the Display with  
the DISP. Button  
Pressing the DISP. button allows you to change the screen display  
mode and toggle the information displayed on the picture display.  
During Shooting Mode  
Normal Symbol Display  
Histogram Display  
Grid Guide Display  
Picture Display Off  
No Display  
(Synchro-Monitor Mode)  
Grid Guide Display-------------------------------------------------------------------  
• This displays auxiliary lines on the picture display to help you compose your  
picture. These lines are not recorded with images.  
• Use [Grid Guide Display Options] on the setup menu to select the grid  
(G P.85).  
Synchro-Monitor Mode-------------------------------------------------------------  
This turns the picture display off except when the camera is operated. This is  
effective for saving power consumption. The picture display turns on when the  
shutter release button is pressed halfway; once a picture has been taken and the  
results displayed, the picture display will turn off (this differs from the [LCD Auto  
Dim] and [Monitor Auto off Delay] options in the setup menu).  
44  
Note-------------------------------------------------------------------------------------  
• When [Shooting Info. Display Frame] is set to [On] in the setup menu, the  
shooting information display frame can be displayed for normal symbol display  
and histogram display (G P.85).  
• Histograms are not displayed in movie mode. A blinking [O] icon, the  
recording time, and the time available are displayed during recording even  
when indicators are hidden or the grid guide is displayed.  
• When [Level Setting] is set to [Display] or [Disp + Snd] (G P.46), the level  
indicator is displayed during normal symbol display and histogram display  
(G P.47).  
• When the picture display is off (including when the display has turned off  
automatically in synchro-monitor mode), pressing any of the following buttons  
turns the picture display on: the MENU/OK, ADJ./MEMO, DISP., 8, 9, 6  
(Playback).  
During Playback Mode  
Normal Symbol  
Display  
Histogram and Detailed  
Information Display  
/
/
No memo present  
Memo present  
Memo Display  
No Display  
45  
Maximizing the Picture Display Brightness  
Hold the DISP. button down in shooting mode to maximize the display  
brightness in shooting mode. When the brightness is at the maximum  
setting, holding the DISP. button down returns the brightness to the  
level set in [LCD Brightness] (G P.83).  
The Level Indicator (Electronic Level)  
If the level indicator is enabled using the  
[Level Setting] option in the setup menu,  
the camera will display an indicator and  
sound a beep to help you keep the camera  
level. The level indicator is displayed during  
normal symbol display and histogram  
display.  
This is useful for keeping the image level when taking pictures of  
scenery or buildings. This is also very useful for taking pictures with the  
horizon visible.  
Available Settings  
Off  
Display  
Description  
The level indicator will not display. The level sound will not emit.  
The level indicator will display. The level sound will not emit.  
The level indicator appears on the screen and a level sound is  
emitted when the image is level.  
Disp + Snd  
Sound  
The level indicator will not display. A level sound is emitted  
when the image is level.  
Highlight [Level Setting] in the  
setup menu (G P.82) and press $.  
1
2
Press the !" buttons to select the setting and then press  
the MENU/OK button.  
46  
Level indicator display  
When level:  
The level indicator becomes green,  
indicating that the scale is in the middle.  
Green  
When tilted to the right or left:  
The mark on the level indicator becomes  
orange, indicating the opposite side of the  
direction in which the camera is tilted.  
Orange  
When the camera is tilted too far to the  
right or left:  
Half of the level indicator on the opposite  
side of the direction in which the camera  
is tilted becomes red. The mark on the  
level indicator is not displayed.  
Red  
When the camera is tilted too far forward  
or backward, or it cannot be determined  
whether the camera is level:  
Red  
The top and bottom of the level indicator  
become red. The mark on the level  
indicator is not displayed.  
When the camera is held vertically:  
When shooting with the camera positioned vertically, the level function  
can be used to determine whether the image is vertically level (the level  
indicator appears in a different place).  
Caution---------------------------------------------------------------------------------  
• Tilt is not shown in synchro-monitor mode or if indicators are hidden or  
the framing grid is displayed (G P.44). When [Level Setting] is set to  
[Display+Sound], only the level sound is emitted.  
• The level function is not available if the camera is held upside down, when  
recording movies, and during interval shooting.  
• The level function becomes less accurate when the camera is moving or when  
shooting in an environment subject to moving, such as on a amusement ride.  
• No level sound is emitted when [Level Setting] is set to [Disp + Snd] or [Sound]  
and [Volume Settings] is set to [ꢀꢀꢀ] (Mute) (G P.84).  
• Use this function as a reference to see if images are level when shooting  
images. The accuracy of the level when using the camera as a level cannot be  
guaranteed.  
47  
About the Histogram Display  
When Histogram is on, a histogram appears  
in the lower right corner on the picture  
display. A histogram is a graph indicating  
the number of pixels on the vertical axis  
and the brightness on the horizontal axis  
(from left to right, shadows (dark areas),  
midtones, and highlights (bright areas)).  
By using the histogram, you can determine the brightness of an image  
without being affected by the brightness around the picture display.  
This also helps you correct for areas that are overly bright or dark.  
If the histogram has only peaks on the  
right side, this picture is overexposed  
with too many pixels only for highlight  
sections.  
If the histogram has only peaks on the left  
side without anything else, this picture  
is underexposed with too many pixels  
only for shadow sections. Refer to this  
histogram when correcting the exposure.  
Note-------------------------------------------------------------------------------------  
• The histogram displayed on the picture display is for reference only.  
• After taking a picture, you can correct its brightness and contrast by making  
adjustments to the histogram (G P.77).  
• Depending on the shooting conditions (use of the flash, dark surrounding light,  
etc.), the exposure level indicated in the histogram may not correspond to the  
brightness of the shot image.  
• Exposure compensation has its limitation. It does not necessarily achieve the  
best possible result.  
• A histogram with peaks in the center may not necessarily provide the best result  
to suit your particular requirements. For example, an adjustment is required if  
you want to underexpose or overexpose the image.  
• For information on how to correct the exposure compensation, see P.69.  
48  
Advanced  
Operations  
1
2
3
Read this section when  
you want to learn more  
about the different camera  
functions.  
4
5
6
1
2
3
4
5
6
7
8
9
ADJ. Button Functions ...................50  
Taking Pictures in Scene Mode ......52  
Shooting and Viewing Movies .......55  
Memos............................................57  
Using Custom Help.........................59  
Shooting Menu...............................62  
Playback Menu...............................72  
Setup Menu ....................................82  
Camera Memo Menu ......................94  
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
10 Expanded Settings Menu...............98  
11 Bluetooth®....................................105  
12 Wireless Networks........................112  
13 GPS ...............................................136  
14 Barcode Reader ............................142  
15 Direct Printing..............................144  
16 Copying Pictures to a Computer via  
USB ...............................................149  
17 Appendices...................................159  
1
ADJ. Button Functions  
The ADJ./MEMO button has the following functions.  
Assigning four functions from the shooting menu (ADJ. mode)  
Shifting the AE and AF targets  
Memos (G P.57)  
1
2
3
1
Selecting Shooting Menu Options Assigned  
to the ADJ./MEMO Button  
You can assign four functions from the shooting menu to the ADJ./  
MEMO button (ADJ. mode). The fifth function is fixed to AE/AF target  
shift (G P.51) and cannot be changed.  
ADJ. mode gives you quick access to settings by pressing a few  
buttons rather than via the menus. It is recommended for options you  
find yourself using frequently.  
Set the functions you want to assign to the ADJ./MEMO  
button with [ADJ Button Setting 1/2/3/4] on the setup  
menu.  
1
• At the time of purchase, four of the functions are assigned. You can  
change the assigned functions.  
Press the ADJ./MEMO button in  
shooting mode.  
2
• The ADJ. mode screen appears.  
Press the #$buttons to select the desired item.  
3
4
Press the !" buttons to select the setting and then press  
the MENU/OK button to confirm the setting.  
Note-------------------------------------------------------------------------------------  
• For functions that can be assigned to the ADJ./MEMO button, see P.170.  
• When using a camera memo, the ADJ. mode is disabled.  
50  
Shifting the AE and AF Targets  
You can shift the target for automatic exposure (AE) and/or auto focus  
(AF).  
Available Setting Description  
1
AE/AF  
AE and AF are set to Spot AE and Spot AF respectively and the  
target can be moved for both simultaneously (The targets for  
Spot AE and Spot AF occupy the same position).  
AF  
The AF is set to Spot AF and the target can be moved. The  
exposure metering is set to the mode selected in [Exposure  
Metering] (G P.63) in the shooting menu.  
AE  
The AE is set to Spot AE and the target can be moved. The focus  
is set to the mode selected in [Focus] (G P.63) in the shooting  
menu.  
Select 5/Vmode and press ADJ./MEMO.  
1
2
3
Press the #$ buttons to select P  
.
Press the !" buttons to select the  
setting and then press the MENU/  
OK or ADJ./MEMO button.  
• The target shift screen appears.  
Press the !"#$ buttons to  
position the target over the subject  
that will be used to set focus or  
exposure.  
4
• Pressing the DISP. button returns the  
display to the screen in Step 2.  
Press MENU/OK or ADJ./MEMO.  
5
6
Press the shutter release button halfway and then gently  
press it the rest of the way down.  
Note-------------------------------------------------------------------------------------  
• In scene mode, the target icon (P ) changes to U . The focus target for macro  
mode can be selected as described above.  
•
This function is not available when [MF] is selected for [Focus] (G P.63).  
51  
2
Taking Pictures in Scene Mode  
Scene Mode Options  
You can use scene mode to select from among  
five still image modes and movie, and shoot with  
settings automatically optimized for shooting  
conditions.  
2
Use when taking pictures in dimly lit places. The picture display also  
becomes brighter.  
High Sens  
Use to capture images under difficult conditions such as the scene  
of a fire. The focal length is fixed to 2.5 m, allowing you to take clear  
pictures in a situation where the auto focus would normally produce  
blurred images due to flames, smoke and water vapor. Increasing the  
ISO sensitivity extends the range of the flash, and prevents camera  
shake by controlling the shutter speed even when the flash is not  
used. The sharpness level is also increased in this mode and the  
picture display becomes brighter and is suited for firefighting.  
Reduce the effects  
Firefighting  
of perspective when  
photographing  
rectangular objects, such  
Skew Correct  
Mode  
as message boards or  
business cards.  
For detailed operations, see P.54. Image size can be set to [a4 : 3 F],  
[a4 : 3 N], or [z4 : 3 F] using the [Picture Quality/Size] option  
(G P.63) in the shooting menu (G P.62).  
Use when capturing text images, for example notes written on a  
whiteboard at a meeting. Images are captured in black and white.  
Image size can be set to [l4 : 3] or [c4 : 3] using the [Size] option  
(G P.63) in the shooting menu (G P.62).  
Text Mode  
The camera automatically zooms to the optimal zoom position to  
shoot at a higher magnification than in normal macro shooting.  
Optical zoom can not be used. Macro mode is selected automatically.  
Zoom Macro  
Movie  
Allows you to shoot movies with sound. For detailed operations, see  
P.55.  
52  
Caution---------------------------------------------------------------------------------  
When using [Zoom Macro], you can shoot close-ups within the following  
distances:  
Minimum Shooting Distance Shooting Range  
(from the front of the lens)  
Approx. 1 cm  
Approx. 14.8 mm × 11.1 mm  
(when digital zoom is not used)  
Approx. 3.7 mm × 2.8 mm  
2
(when 4.0 × digital zoom is used)  
Selecting a Scene Mode  
Turn the mode dial to W.  
1
• The camera is ready to shoot and the  
selected scene mode is displayed at the  
top of the picture display.  
Press the MENU/OK button to  
change the scene mode.  
2
• The scene mode selection screen  
appears.  
Select a scene mode.  
3
4
Press the MENU/OK button.  
• The scene mode type is displayed at  
the top of the picture display.  
Press the shutter release button to  
shoot the picture.  
5
Changing the shooting menu or setup menu setting in scene mode ----  
Press the MENU/OK button in shooting mode and then press the # button to  
select [MODE] tab. You can then press " once to display the shooting menu,  
twice to display the setup menu.  
53  
Using Skew Correction Mode  
Select [Skew Correct Mode] in the scene mode menu and  
press the MENU/OK button.  
1
Press the shutter release button to shoot the picture.  
2
• The display indicates that the image is being processed, and then  
the area recognized as the correction range is displayed with an  
orange frame. Up to five areas can be recognized.  
2
• If the target area cannot be detected, an error message appears. The  
original image remains unchanged.  
• To select another correction area, move the orange frame to the  
target area by pressing the $ button.  
• To cancel skew correction, press the ! button. Even if you cancel  
skew correction, the original image remains unchanged.  
Press the MENU/OK button.  
• The display indicates that the image is being corrected, and then the  
corrected image is recorded. The original image remains unchanged.  
3
Note-------------------------------------------------------------------------------------  
You can also correct the skew of a previously shot still image (G P.78).  
Caution---------------------------------------------------------------------------------  
When [Skew Correct Mode] is selected, note the following:  
• To shoot the subject as large as possible, position it so that the entire portion  
of the subject is visible on the picture display.  
• The camera may fail to recognize the subject in the following cases:  
- When the image is out of focus  
- When four edges of the subject are not clearly visible  
- When it is hard to distinguish between the subject and background  
- When the background is complicated  
• Two images, one before correction and the other after correction, are  
recorded. If the number of remaining shots is less than two, you cannot shoot  
the subject.  
• The correction area may not be detected properly if the [Date Imprint]  
function is activated.  
54  
3
Shooting and Viewing Movies  
Shooting Movies  
Select [Movie] in the scene mode menu to record movies with sound.  
Frame size can be selected as described on P.63. Each movie you shoot  
is recorded as an AVI file.  
/
Press the shutter release button to start  
recording. The [O] icon will blink. To  
zoom in or out using digital zoom, press  
z or Z (G P.33). The recording time  
and time available are displayed during  
recording. Press the shutter release button  
again to end recording.  
3
Caution---------------------------------------------------------------------------------  
• While shooting movies, operation sounds may be recorded.  
• Movies may be up to 4 GB in size. The maximum length is 12 minutes for  
movies recorded at a [Movie Size] of [x1280] and 29 minutes for movies  
recorded at [z640] or [y320]. Depending on the type of memory card used,  
shooting may end before this length is reached. The maximum total length of  
all movie files that can be stored depends on the capacity of the memory card  
(G P.174).  
• Flicker may be visible in movies recorded under fluorescent lights.  
Note-------------------------------------------------------------------------------------  
• The remaining recording time may not change uniformly because it is  
recalculated from the remaining memory capacity during movie recording.  
• Depending on the remaining battery level, the battery may become depleted  
during movie shooting. Use of a battery with adequate remaining power is  
recommended.  
• An SD/SDHC memory card with a Speed Class of 6 or better is recommended  
when recording movies with [x1280] selected for [Movie Size] (G P.63).  
55  
Playing Back Movies  
To play back movies, follow the steps below.  
/
Select the movie you want to play  
back in playback mode.  
1
Press the ADJ./MEMO button.  
2
• Playback begins. The elapsed playback  
indicator or the elapsed time is  
displayed on the screen.  
3
Fast Forward  
Rewind  
Pause/Playback  
Slow Playback  
Slow Rewind  
Next Frame  
Press the z button during playback.  
Press the Z button during playback.  
Press the ADJ./MEMO button.  
Press and hold the z button during pause.  
Press and hold the Z button during pause.  
Press the z button during pause.  
Press the Z button during pause.  
Press the !" buttons during playback.  
Previous Frame  
Volume Adjustment  
56  
4
Memos  
For information on creating, transferring, and configuring memo lists,  
see the supplied “Software User Guide”.  
Image files created with the camera contain fields that can be used  
to store information about the image. The camera memo function  
employs these fields for memos that can be used to identify and  
classify photos. Read this section for basic information on using  
memos.  
4
Caution---------------------------------------------------------------------------------  
• Memos can not be added to movies.  
• SD WORM memory cards do not support memos.  
• Note that the presence of commas, multiple periods, or any of the following  
characters may corrupt the display of item names in Russianlanguage operating  
systems: \ / : ? * " < > |  
Adding Memos to New Photos  
This section describes how to create memos from an existing memo  
list that has been transferred to the camera.  
Select 5/Vmode and press  
ADJ./MEMO.  
1
• The camera memo dialog will be  
displayed.  
Create a memo.  
2
• If [Mode1] is selected for [Camera  
Memo Mode] (G P.95) in the camera  
memo menu, press ! or " to highlight  
an item, and then press $ and press  
! or " to choose a description.  
If [Mode2] is selected, press # or  
$ to choose from pre-existing  
combinations.  
Items  
Descriptions  
57  
Press MENU/OK.  
• Press MENU/OK to accept the current memo.  
3
4
Take photographs.  
• The memo will be added to all new photos.  
Viewing Memos  
The process for viewing memos varies with the option selected for  
[Camera Memo Mode] (G P.95) in the camera memo menu.  
Mode1  
4
/
Display the desired photo in  
playback mode.  
• Photographs to which memos have  
been added are indicated by a “MEMO”  
icon.  
1
2
3
Press ADJ./MEMO.  
• The memo will be displayed as  
shown at right. Press ! or " to view  
additional data. If desired, the memo  
can be edited as described on P.29 of  
the “Software User Guide”.  
Press MENU/OK.  
• Press MENU/OK to return to normal playback.  
Mode2  
Memos can be displayed only by pressing DISP. during playback  
(G P.45); memos can not be edited.  
58  
5
Using Custom Help  
Pressing DISP. when [On] is selected for [Custom Help] (G P.104) in  
the expanded settings menu (G P.98) displays previously-selected  
JPEG images (“custom help”). Custom help is available in the shooting  
(G P.62) and playback (G P.72) menus.  
Creating Custom Help  
The JPEG images must first be copied to a memory card and then  
copied from the card to the camera’s internal memory.  
Ready a memory card.  
• Connect the camera or a memory card reader to the computer and  
insert a memory card that has been formatted in the camera.  
1
5
Copy the images to the [IMPORT] folder.  
• Copy the JPEG images to the [IMPORT] folder on the memory card.  
Be sure that the folder contains no more than 99 images.  
2
Disconnect the camera or card reader.  
3
• Disconnect the device as described on P.156. If you are using a card  
reader, remove the memory card and insert the card in the camera  
(G P.27).  
Select [Admin Mode [Regist]].  
4
• Highlight [Admin Mode [Regist]] in the  
expanded settings menu (G P.98) and  
press $. You will be prompted to enter  
a password.  
Enter a password.  
5
• Enter the password created using the [Admin Pass Key] option  
(G P.104) in the expanded settings menu (G P.98; the default  
password is “0000”) and press ADJ./MEMO (for information on  
entering a password, see P.91). A confirmation dialog will be  
displayed if the password is correct; entering an incorrect password  
returns you to the expanded settings menu.  
59  
Select [Yes].  
6
• Highlight [Yes] and press MENU/OK to  
copy the images to internal memory  
and return to the expanded settings  
menu. If memory is insufficient, a  
warning will be displayed and copying  
will be interrupted. Any custom help  
images copied to that point will remain  
in internal memory.  
Note-------------------------------------------------------------------------------------  
• Any existing custom help in internal memory is overwritten.  
• Custom help can not be copied to a memory card using the [Copy to Card from  
Internal Memory] option (G P.73) in the playback menu (G P.72).  
5
Caution---------------------------------------------------------------------------------  
The images used for custom help must conform to the following:  
• Color space: YCbCr 4 : 2 : 2 or 4 : 2 : 0  
• Dimensions (W × H): From 32 × 32 to 4000 × 3000 pixels, where the width  
is a multiple of 16 and the height a multiple of 8 (YCbCr 4 : 2 : 2) or 16 (YCbCr  
4 : 2 : 0)  
• File size: 12 MB or less  
• File name: A four-character prefix followed by a four-digit number and the  
extension“.jpg”(e.g., “PLAY0001.jpg”)  
60  
Viewing Custom Help  
Display the menus.  
• Press MENU/OK to display the shooting or playback menu.  
1
2
Press DISP.  
• Custom help is displayed in  
How to Use the Mode Dial  
ascending order by file name. Press  
Set the mode dial to  
the desired mode  
before shooting still  
# or $ to page through help one file  
images or movies.  
at a time, or ! or " to skip ten files  
forward or back. Custom help can  
Mode Dial Symbols and Descriptions  
Symbol  
Function  
CALS Mode  
Description  
Refer to  
P. 3 7  
Quality and size are adjusted to  
produce photographs suitable for  
public works photography. Picture  
quality and size can be selected  
from six options using the [CALS  
Pic Quality] item in the setup menu  
(GP.87).  
be displayed twenty files at a time  
(G P.38) or viewed in enlarged view  
(G P.40), but can not be displaying  
V
5
using the 6 button or deleted by pressing D. Use [Admin Mode  
[Delete]] (G P.104) to delete custom help.  
Exit.  
3
• Press DISP. to return to the menus or press the shutter release button  
halfway or rotate the mode dial to exit to shooting mode.  
Deleting Custom Help---------------------------------------------------------------  
To delete custom help, select [Admin Mode [Delete]] (G P.104) in the expanded  
settings menu (G P.98) and use the D button as described on P.41.  
61  
6
Shooting Menu  
The shooting menu is used to adjust camera settings when taking  
pictures. To display the shooting menu, press the MENU/OK button  
when the camera is in shooting mode.  
Using the Menu  
Press the MENU/OK button in  
shooting mode.  
1
• The shooting menu is displayed.  
• In scene mode, press # to highlight  
the [MODE] tab, press " once to  
highlight the shooting menu tab,  
and press $ to place the cursor in  
6
Indicates the range of displayed  
the shooting menu.  
screens.  
Press the !" buttons to select the  
desired menu item.  
2
• If the DISP. button is pressed at this  
point, the cursor moves to the shooting  
menu tab.  
• Press the " button at the bottom item  
to display the next screen.  
Press the $ button.  
• The menu item settings are displayed.  
3
Press the !" buttons to select the  
setting.  
4
Press the MENU/OK button.  
• The setting is confirmed, the shooting menu disappears and the  
camera is ready to shoot.  
5
• To select the highlighted option and return to the menu shown in  
Step 2, press the # button.  
62  
Shooting Menu Options  
Density  
Adjust contrast when using the [Text Mode] option in scene mode.  
Size  
G
P.174  
Choose the size of pictures taken using the [Text Mode] option in scene mode.  
Movie Size  
Choose the movie frame size.  
Picture Quality/Size  
Adjust picture quality and size when taking pictures.  
Focus  
G
G
G
P.174  
P.174  
P.67  
Choose a focusing mode.  
—
Multi AF  
Measures the distances from nine AF areas and focuses to the nearest AF  
area. Choose to prevent out-of-focus photos.  
Spot AF  
6
—
Selects one AF area at the center of the picture display to allow the camera  
to focus on this area automatically.  
MF  
Enables you to adjust the focus manually (G P.67).  
Snap  
Fixes the shooting distance to a short distance (approx. 2.5m (8.2ft.)).  
∞ (Infinity)  
Fixes the shooting distance to infinity. It is useful for shooting distant scenes.  
Exposure Metering  
You can change the metering method (the range to use for metering) used to  
determine the exposure value.  
—
Multi  
The entire shooting range is divided into 256 partitions, and each is metered  
to determine the overall exposure value.  
Center  
The entire image is metered, with emphasis on the center, to determine  
the exposure value. Use this when the brightness of the center and  
surroundings are different.  
Spot  
Only the center of the image is metered to determine the exposure value.  
Use this setting when you want to use the brightness at the center. This is  
useful if there is a marked difference in contrast or backlighting.  
63  
Continuous Mode  
The camera records photographs one after the other  
while the shutter release button is pressed. Select  
[Off] to take one photo each time the shutter release  
button is pressed.  
Caution------------------------------------------------------------------------------  
• Focus and exposure value are locked.  
• The number of images that can be shot in continuous mode depends on the  
image size setting.  
• When [Card Sequence No.] is set to [On] (G P.86) and the last four digits of  
the file number exceed“9999”during continuous shooting, a separate folder  
is created in the SD memory card and successive pictures taken in continuous  
mode are stored in this folder.  
• The maximum number of consecutive shots that can be taken using  
continuous mode is 999.  
6
Image Settings  
Adjust contrast, sharpness, and vividness.  
Vivid  
Take strong, vivid photos with heightened contrast, sharpness, and  
vividness.  
—
Standard  
Creates an image with normal picture quality.  
Black & White  
Creates a black and white picture.  
Auto Bracket  
G
P.68  
Vary exposure or white balance over a series of pictures.  
Time Exposure  
Use time exposures to capture fireworks as they rise into the air and explode,  
to create trails of light behind cars and other moving objects, or to shoot night  
scenery. Choose the exposure time from [Off], [1 second], [2 seconds], [4 seconds],  
and [8 seconds].  
Note----------------------------------------------------------------------------------  
• The shutter speed may slow down and images may be blurred. Hold the  
camera steady by using a tripod when shooting.  
• The picture display turns off while shooting.  
64  
Interval Shooting  
Take photos automatically at intervals ranging  
from five seconds to three hours in five-second  
increments.  
Hours Minutes Seconds  
Caution------------------------------------------------------------------------------  
• The interval shooting setting is cleared when the camera is turned off.  
• The time until the next picture can be taken according to the shooting menu  
setting may be longer than the time set for interval shooting. If this is the case,  
the shooting interval becomes longer than the set time.  
Note----------------------------------------------------------------------------------  
• Depending on the remaining battery level, the battery may become depleted  
during interval shooting. Use of a battery with adequate remaining power is  
recommended.  
6
• If you press the shutter release button during interval shooting, the camera  
shoots as usual.  
• A high speed memory card or a SD memory card with sufficient memory is  
recommended.  
Camera Shake Correction  
Select [On] to reduce the effects of camera shake.  
Caution------------------------------------------------------------------------------  
• The camera shake correction function cannot prevent movement of the  
shooting subject (caused by wind, etc.).  
• Results vary with shooting conditions.  
Note----------------------------------------------------------------------------------  
The J symbol appears when camera shake is likely to occur (G P.20).  
Date Imprint  
You can insert the date (YY/MM/DD) or the date and time (YY/MM/DD hh:mm) at  
the lower right of a still image. Select [Off] to turn date imprint off.  
Note----------------------------------------------------------------------------------  
• Make the date and time settings in advance (G P.30).  
• [Date Imprint] cannot be used with movies.  
• The date imprinted in an image cannot be deleted.  
Exposure Compensation  
G
P.69  
Choose exposure compensation.  
65  
White Balance  
Adjust the white balance.  
ISO Setting  
G
G
P.70  
P.71  
Adjust ISO sensitivity.  
Edit Detection  
If pictures taken with [On] selected for this option are transferred to a computer,  
changes made after the images were recorded can be detected using image  
authentication software, including the supplied EC1 application.  
Caution------------------------------------------------------------------------------  
• Recording times increase when [On] is selected.  
• Changes made using the [Resize], [Contrast Correction], and [Skew Correction]  
options in the playback menu will be detected by image authentication  
software.  
Restore Defaults  
Select [Yes] and press the MENU/OK button to restore shooting menu settings to  
their default values.  
6
Shooting menu options ------------------------------------------------------------  
The options displayed in the shooting menu vary with the selected shooting  
mode. In scene mode, the options displayed vary with the selected scene. See  
P.169 for more information.  
66  
Focus  
Manual Focus (MF)  
Manual focus (MF) can be used to focus  
at a selected distance when the camera is  
unable to focus using autofocus. A focus  
bar is displayed in the picture display.  
Press and hold the MENU/OK button as required.  
• Pressing and holding the MENU/OK button increases the  
magnification only at the center of the screen.  
1
• Pressing and holding the MENU/OK button again returns from  
enlarged view to normal view.  
6
Adjust the zoom position with the z Z buttons as required.  
2
3
Press the !" buttons to adjust the focus.  
• Pressing the ! button adjusts the focus to farther objects and  
pressing the " button adjusts the focus to closer objects.  
Press the shutter release button to shoot the picture.  
4
Note-------------------------------------------------------------------------------------  
You can also use manual focus to focus on objects within the macro shooting  
range.  
67  
Auto Bracket  
Choose the type of bracketing performed.  
Auto Bracket  
If [On] is selected, the camera will take  
three photos each time the shutter release  
button is pressed: one underexposed  
by 0.5EV, a second at current exposure  
settings, and a third overexposed by 0.5EV.  
Recording  
An icon is displayed when [On] is selected.  
Note-------------------------------------------------------------------------------------  
The exposure compensation can be changed using the shooting menu  
(G P.69).  
6
White Balance Bracket (WB-BKT)  
The white balance bracket function  
automatically records three images—a  
reddish image, a bluish image, and an  
image of the current white balance.  
An icon is displayed when [WB-BKT] is  
selected.  
Note-------------------------------------------------------------------------------------  
• The white balance can be changed using the shooting menu (G P.70).  
• Although white balance bracketing can be selected when [Black & White] is  
chosen for [Image Settings], bracketing will not be performed.  
68  
Exposure Compensation  
Use exposure compensation to vary exposure from the value selected  
by the camera. Choose from values between –2 and +2; negative  
values produce darker pictures, positive values brighter pictures.  
Exposure compensation may be required in the following situations:  
For backlighting  
When the background is particularly bright, the subject will appear  
dark (underexposed). In this case, set the exposure level higher (+).  
When your subject is whitish  
The entire picture will turn out dark (underexposed). Set the exposure  
level higher (+).  
When your subject is darkish  
6
The entire picture will turn out bright (overexposed). Set the exposure  
level lower (–). The same happens when you take a photo of a subject  
in a spotlight.  
Press the !" buttons to choose a  
exposure value and press the MENU/OK  
button. The selected value is displayed in  
the picture display.  
–
Note-------------------------------------------------------------------------------------  
If the subject is very bright or very dark, [Q] will be displayed and exposure  
compensation will not be available.  
69  
White Balance  
Adjust the white balance so that a white subject will appear white. At  
purchase, the white balance mode is set to [Auto]. Change the setting  
in situations where the white balance is difficult to adjust effectively,  
such as when shooting an object of a single color or when shooting  
under multiple light sources.  
AUTO Auto  
Adjusts the white balance automatically.  
Outdoors  
Select this when shooting outdoors (sunny) and white balance fails to adjust  
properly.  
Cloudy  
Select this when shooting in cloudy weather or shade and the white balance  
fails to adjust properly.  
6
Incandescent 1  
Select this when shooting under incandescent light and white balance fails to  
adjust properly.  
Incandescent 2  
Select this when shooting under incandescent light (more reddish, compared  
with [Incandescent 1]).  
Fluorescent  
Select this when shooting under fluorescent light and white balance fails to  
adjust properly.  
Manual  
Adjust the white balance manually (G P.71).  
Ring Light  
Adjust white balance manually as described on P.71. The selected value is  
not reset when defaults are restored using [Restore Defaults].  
Note-------------------------------------------------------------------------------------  
• The white balance may not be adjusted correctly for a subject that is mostly  
dark. In this case, add something white to the subject.  
• When shooting with the flash, the white balance may not be adjusted correctly  
if [Auto] is not selected. In this case, switch to [Auto] to shoot with the flash.  
70  
Manual  
Measure white balance.  
1
• After selecting [Manual] in the white balance menu and placing a  
blank piece of paper or other white object under the lighting you  
wish to measure, aim the camera at the object and press the DISP.  
button to measure white balance.  
Press the MENU/OK button.  
• The symbol appears on the screen.  
2
• The effect of the selected white balance setting can be previewed in  
the picture display. Repeat the above steps until the desired effect is  
achieved.  
Note-------------------------------------------------------------------------------------  
To cancel [Manual], select a setting other than [Manual].  
6
ISO Setting  
ISO sensitivity indicates how sensitive film is to light. A greater value  
means higher sensitivity. High sensitivity is suitable for shooting  
an object in a dark place or a fast-moving object while minimizing  
blurring. When ISO setting is set to [Auto], the camera automatically  
changes the sensitivity according to the distance, brightness, zoom,  
macro settings, and picture quality/size. Choose settings other than  
[Auto] to fix ISO sensitivity at the selected value.  
Note-------------------------------------------------------------------------------------  
• When the flash is used, the maximum value that will be selected for auto  
ISO sensitivity is ISO 400. If the flash is off and image size is set to [l4 : 3 F]  
or [l4 : 3 N], auto ISO sensitivity will be set to values between ISO 64 and  
ISO 400.  
• When the flash is set to [FLASH ON (10M)], the maximum value that will be  
selected for auto ISO sensitivity is ISO 1600.  
• Images shot with a higher sensitivity may appear grainy.  
• When [Auto] is selected for ISO sensitivity, the ISO value displayed when the  
shutter release button is pressed halfway may in some instances (for example,  
when the flash is used) differ from the value selected when the shutter is  
released.  
71  
7
Playback Menu  
The options in the playback menu can be used to perform a variety of  
operations on existing pictures. To display the playback menu, select  
playback mode and press the MENU/OK button.  
Using the Menu  
Press the 6 (Playback) button to select the playback mode.  
1
2
Press the !"#$ buttons to display the desired file.  
• For [Slide Show] (G P.73), [Copy to Card from Internal Memory]  
(G P.73), or [Recover File] (G P.74), skip this step.  
Press the MENU/OK button.  
• The playback menu appears.  
3
7
Press the !" buttons to select the  
desired item.  
4
• If the DISP. button is pressed at this  
point, the cursor moves to the playback  
menu tab.  
Press the $ button.  
• The screen for the selected menu item appears.  
5
72  
Playback Menu Options  
Resize  
You can reduce the image size of a shot still image to create a new file with a  
different image size.  
Original  
Resized  
l4 : 3F/l4 : 3N/j3 : 2F/e4 : 3F/c4 : 3F/  
a4 : 3F/z4 : 3F  
b4 : 3F  
a4 : 3F/a4 : 3N  
z4 : 3F  
Caution------------------------------------------------------------------------------  
Movies cannot be resized.  
Trim  
G
P.75  
This function allows you to trim a still image you have shot and then save it as a  
separate file.  
Contrast Correction  
G
P.77  
Create copies of photographs with modified brightness and contrast.  
7
Skew Correction  
G
P.78  
Create copies that have been processed to reduce the effects of perspective on  
rectangular objects.  
Protect  
G
P.79  
Protect images from accidental deletion.  
Slide Show  
You can display the recorded still images and movie files sequentially on the screen.  
Note----------------------------------------------------------------------------------  
• Each still image is displayed for three seconds.  
• Movies are played back in their entirety.  
Copy to Card from Internal Memory  
Copy all data from internal memory to a memory card in a single operation.  
Note----------------------------------------------------------------------------------  
• If there is not enough space available on the destination memory card, a  
warning will be displayed. Select [Yes] to copy only those files for which there is  
sufficient space.  
• It is not possible to copy the contents of an SD memory card to the internal  
memory.  
DPOF  
G
P.80  
Select pictures for printing.  
73  
Recover File  
Restore deleted files.  
Caution------------------------------------------------------------------------------  
Deleted files cannot be restored after performing any of the following operations.  
• Turning the camera off  
• Switching from playback mode to shooting mode  
• Using DPOF, Resize, Copy to Card from Internal Memory, Skew Correction,  
Contrast Correction or Trim  
• Files with DPOF settings are deleted  
• Internal memory or SD memory card is initialized  
• Altering memos in playback mode  
File Send  
G
P.105  
Copy files to a computer over a wireless LAN or using Bluetooth®.  
7
74  
Trim  
Create a cropped copy of the current photograph.  
Press 8 or 9 to adjust the crop size and  
press !, ", #, or $ to position the crop.  
Press the MENU/OK button to save the  
cropped image to a separate file.  
Caution---------------------------------------------------------------------------------  
• You can only trim still images shot using this camera.  
• While you can trim an image repeatedly, the image is recompressed each time  
and there will be some decline in image quality.  
Note-------------------------------------------------------------------------------------  
• To cancel, press the DISP. button.  
7
• To view help, press the D button while the crop display is shown in the picture  
display. Press the D button again to exit help.  
• If an image is trimmed, the compression ratio changes to Fine.  
• The available settings for the trimming frame size differ depending on the  
original image size.  
75  
• The size of the image after cropping depends on the size of the original and the  
size of the crop (the crop displayed when you select [Trim] is the second largest;  
to select the largest crop, press 9).  
Original image size  
Trimming level  
Trimmed image size  
4000 × 3000  
2592 × 1944  
2048 × 1536  
1600 × 1200  
1280 × 960  
640 × 480  
1, 2  
3
4, 5  
l4 : 3 F/l4 : 3 N  
(4000 × 3000)  
6
7 to 10  
11 to 14  
1
2, 3  
4
5 to 7  
8 to 11  
1
2
3
2592 × 1944  
2048 × 1536  
1600 × 1200  
1280 × 960  
640 × 480  
2592 × 1944  
2048 × 1536  
1600 × 1200  
1280 × 960  
640 × 480  
2048 × 1536  
1600 × 1200  
1280 × 960  
640 × 480  
1600 × 1200  
1280 × 960  
640 × 480  
j3 : 2 F  
(3984 × 2656)  
e4 : 3 F  
(2592 × 1944)  
7
4 to 7  
8 to 12  
1
2
c4 : 3 F  
(2048 × 1536)  
3 to 6  
7 to 10  
1
2 to 4  
5 to 9  
1 to 3  
4 to 8  
b4 : 3 F  
(1600 × 1200)  
1280 × 960  
640 × 480  
a4 : 3 F/a4 : 3 N  
(1280 × 960)  
z4 : 3 F  
(640 × 480)  
1 to 4  
640 × 480  
76  
Contrast Correction  
Create copies that have been processed to adjust brightness and  
contrast.  
Highlight [Contrast Correction] in the  
playback menu and press $ to display a  
level slider and histogram.  
Press ! to make the photo brighter, or  
" to make it darker. Five settings are  
available.  
Press the MENU/OK button. The display indicates that the image is  
being corrected, and then the corrected image is recorded.  
Caution---------------------------------------------------------------------------------  
• If the camera can not create a corrected copy, an error message will be  
displayed and the camera will exit to the playback menu.  
7
• To cancel contrast correction, press the DISP. button.  
• You can correct the contrast for still images shot with this camera. You cannot  
correct the contrast for movies.  
• The desired results may not be achieved with photographs taken with [Text  
Mode] selected in scene mode or with [Black & White] selected for [Image  
Settings].  
• While you can use contrast correction repeatedly, the image is recompressed  
each time and there will be some decline in image quality.  
77  
Skew Correction  
Create copies that have been processed to reduce the effects of  
perspective on rectangular objects, such as message boards or  
business cards.  
Caution---------------------------------------------------------------------------------  
You can use skew correction for still images shot with this camera. You cannot use  
skew correction for movies.  
Note-------------------------------------------------------------------------------------  
• If the camera is able to detect an object that can be used to correct perspective,  
a message will be displayed with the object shown by an orange frame. The  
camera can detect up to five objects.  
• If the target area cannot be detected, an error message appears. The original  
image remains unchanged.  
• To select another correction area, move the orange frame to the target area by  
pressing the $ button.  
• To cancel skew correction, press the ! button. Even if you cancel skew  
correction, the original image remains unchanged.  
7
• The image size does not change for skew corrected images.  
• If the image size is large, skew correction will take time. Resize the image  
(G P.73) before performing skew correction to speed up the process.  
• The following table shows the approximate time required for skew correction.  
Image Size  
l4 : 3 F  
l4 : 3 N  
j3 : 2 F  
e4 : 3 F  
c4 : 3 F  
Correction time  
Image Size  
b4 : 3 F  
a4 : 3 F  
a4 : 3 N  
z4 : 3 F  
Correction time  
Approx. 6 seconds  
Approx. 4 seconds  
Approx. 4 seconds  
Approx. 2 seconds  
Approx. 29 seconds  
Approx. 28 seconds  
Approx. 24 seconds  
Approx. 13 seconds  
Approx. 8 seconds  
• When scene mode is set to [Skew Correct Mode], you can shoot an image and  
then immediately correct any skew in the image (G P.54).  
78  
Protect  
[Protect] allows you to protect files from  
being accidentally deleted.  
If [1 File] is selected, you can protect or  
unprotect the file selected by pressing the  
#$ buttons.  
If [Select All] or [Cancel All] is selected, you  
can protect or unprotect all files.  
Selecting Multiple Files  
Select [Sel Mult] to change the protect status of multiple individual  
files or of all files in a selected range.  
To select multiple individual frames:  
Select [Sel. Indiv.] and press the MENU/OK button.  
1
2
7
Select a frame and press the MENU/OK button.  
• Press the ADJ./MEMO button to switch to the display for specifying a  
range of files.  
• If you selected a file by mistake, you can deselect it by selecting the  
file and pressing the MENU/OK button.  
• Select all files you want to protect.  
Press the D button.  
3
To select two frames and all frames between them:  
Select [Sel. Range] and press the MENU/OK button.  
1
2
Select the first frame and press the MENU/OK button.  
• Press the ADJ./MEMO button to switch to the display for specifying  
files separately.  
• If you make a mistake when selecting the starting point for the range  
of files, press the DISP. button to return to the screen for selecting  
the starting point.  
79  
/
Select the last frame and press the  
MENU/OK button.  
• Repeat Steps 2 and 3 to select multiple  
ranges.  
3
4
Press the D button.  
Note-------------------------------------------------------------------------------------  
[Sel. Indiv.] and [Sel. Range] can be selected directly if [Protect] is chosen in  
thumbnail view.  
Caution---------------------------------------------------------------------------------  
Note that formatting deletes all files, including protected files.  
DPOF  
To request professional prints of the  
photographs on a memory card, first use  
this option to create a digital “print order”  
listing the photos you wish to print and  
the number of prints, and then take the  
memory card to a digital print service  
center that supports the DPOF standard.  
7
To add a photo to or remove it from the print order, select [1 File] and  
press the #$ buttons to display the desired file.  
Select [Select All] to add all photos to the print order, or [Cancel All] to  
remove all files from the print order.  
Selecting Multiple Files  
To change the print status of multiple individual files, select [DPOF] in  
thumbnail view.  
Select photos and press the !" buttons to choose the number of  
prints; press the ! button to increase the number of copies, or press  
the " button to decrease the number of copies.  
Press the MENU/OK button to exit when settings are complete.  
80  
Note-------------------------------------------------------------------------------------  
To remove the DPOF settings for multiple still images, follow the same steps  
described above to set the number of copies to print to [0] for each image, and  
then press the MENU/OK button.  
Viewing Pictures on TV  
To view pictures on a TV, connect the camera using the supplied AV  
cable.  
Securely connect the AV cable to the Video Input Terminal (yellow)  
Video In terminal on the television.  
1
• Connect the white plug of the AV cable  
to the audio input terminal (white) of the  
TV unit and the yellow plug to the video  
input terminal (yellow).  
Turn the camera off and securely  
connect the cable to the camera AV  
2
Audio Input Terminal (white)  
7
output terminal.  
Set the television to Video mode (Set the input to Video).  
• For details, see the documentation that came with the television.  
3
Press the POWER button, or press and hold the 6  
(Playback) button to turn the camera on.  
4
Caution---------------------------------------------------------------------------------  
• When the AV cable is connected to the camera, the picture display and the  
speaker output turn off.  
• Do not force the AV cable into the terminal.  
• Do not apply excessive force with the AV cable connected.  
• When using the AV cable, do not move the camera with the AV cable.  
Note-------------------------------------------------------------------------------------  
• You can connect the AV cable to the Video In terminal on your video recorder  
and record what you have shot to a video recorder.  
• The camera supports the following video standards: NTSC and PAL. Where  
possible, the camera is set to the standard used in your country or region before  
shipment; before connecting the camera to a device that uses a different video  
standard, choose the appropriate video mode (G P.86).  
81  
8
Setup Menu  
You can change the camera settings by displaying the setup menu  
from the shooting menu (G P.62) or playback menu (G P.72).  
Using the Menu  
Press the MENU/OK button.  
• The shooting menu (or the playback menu) appears.  
1
Press # to highlight the tab for the current menu.  
2
3
Press ! or " to highlight the  
setup menu tab.  
• The setup menu tab is second from  
the top.  
Indicates the range of displayed  
screens.  
8
Press $ to place the cursor in the setup menu.  
4
5
Press the !" buttons to select the  
desired item.  
• If the DISP. button is pressed at this  
point, the display returns to the screen  
shown in Step 3.  
• Press the " button at the bottom item  
to display the next screen.  
Press the $ button.  
• The menu item settings are displayed.  
6
Press the !" buttons to select the  
setting.  
7
82  
Press MENU/OK, or press # and then MENU/OK.  
• The setup menu disappears and the camera is ready for shooting or  
playback.  
8
• The setup menu may appear depending on the setting. In this case,  
press the MENU/OK button to return to the shooting or playback  
screen.  
• Pressing the # button in Step 8 confirms the setting and the display  
returns to the screen shown in Step 5.  
Note-------------------------------------------------------------------------------------  
For some functions, the setting selection method may differ from what is  
explained here. For detailed operation, see the explanation of each function.  
Setup Menu Options  
Format [Card]  
Select [Yes] and press the D button to format the memory card.  
Caution------------------------------------------------------------------------------  
Do not turn the camera off during formatting. Failure to observe this precaution  
could result in the system files used by the camera being deleted.  
8
Format [Internal Memory]  
Select [Yes] and press the D button to format internal memory. If you have images  
in the internal memory that you do not want to delete, copy the images to the SD  
memory card before formatting the internal memory (G P.73).  
Caution------------------------------------------------------------------------------  
Do not turn the camera off during formatting. Failure to observe this precaution  
could result in the system files used by the camera being deleted.  
LCD Brightness  
Press the !" buttons to adjust the brightness of the picture display.  
Reg. My Settings  
G
P.88  
Save current camera settings.  
Stepped Zoom  
Select [On] to allow zoom to be adjusted in discrete steps that on a 35-mm  
camera would be equivalent to focal lengths of 28 mm, 35 mm, 50 mm, 85 mm,  
105 mm and 140 mm. In macro mode, the stepped zoom focal lengths are roughly  
equivalent to 33, 35, 50, 85, 105 and 140 mm on a 35-mm camera.  
83  
ADJ Button Setting 1–4  
G
P.50  
Choose the role performed by the ADJ./MEMO button.  
AF Auxiliary Light  
If [On] is selected, the AF auxiliary light will light to assist autofocus.  
Operation Sounds  
Choose the sounds made by the camera.  
Available Settings Description  
All  
All sounds on.  
Level Sound  
Shutter Sounds  
Only the level sound is emitted.  
Only the shutter sound and level sound are emitted.  
Note----------------------------------------------------------------------------------  
If you try to perform an operation that cannot be performed, the beep sound is  
emitted regardless of the [Operation Sounds] setting.  
Volume Settings  
The operation sound volume can be changed.  
Note----------------------------------------------------------------------------------  
When [Volume Settings] is set to [ꢀꢀꢀ] (Mute), the level sound is not emitted  
even when [Level Setting] is set to [Disp+Snd] or [Sound].  
8
LCD Confirmation Time  
Choose how long photos are displayed after shooting. Photos will not be displayed  
if [Off] is selected.  
Auto Power Off  
Choose how long the camera remains on when no operations are performed.  
The camera will not turn off automatically if [Off] is selected, during interval timer  
photography (G P.65), or when the camera is connected to a computer or printer.  
Monitor Auto off Delay  
Choose the delay before the picture display turns off automatically to save power  
when no operations are performed. Once the display has turned off, any operation  
will reactivate the display. This option takes effect only when [Off] is selected for  
[Auto Power Off].  
LCD Auto Dim  
If [On] is selected, the picture display will automatically dim to save power if no  
operations are performed for about five seconds. This feature is not available in  
synchro-monitor mode (G P.44).  
84  
Digital Zoom Image  
G
P.89  
Choose [Auto Resize] to record pictures taken with digital zoom at actual size,  
[Normal] to enlarge image data from the center of the frame.  
Level Setting  
Adjust level indicator and level sound settings.  
Grid Guide Display Options  
G
P.46  
P.44  
G
Choose the type of framing grid available in shooting mode.  
Available Settings Description  
A three-by-three grid for“rule of thirds”composition.  
A four-by-four grid with diagonal lines running from corner  
to corner makes it easy to find the center of the subject. Use  
for architectural photography or photographing products for  
display.  
A two-by-two grid with the center of the frame left clear to  
make it easier to view the subject. Use if your subject is in  
motion.  
8
Shooting Info. Display Frame  
Select [On] to display shooting icons in a frame  
surrounding the view through the lens (G P.44).  
Shooting information display frame cannot be used  
in movie mode.  
+
Auto Rotate  
Select [On] to automatically display pictures in the correct orientation during  
playback.  
85  
Card Sequence No.  
When you switch SD memory cards, you can set your camera to continue  
consecutive numbering from the previously loaded card.  
Available Settings Description  
On (Continue  
numbering)  
Files names consist of“R”followed by a seven-digit number (e.g.,  
“R0010001.jpg”), assigned in ascending order from 0010001 to  
9999999. When a new memory card is inserted, file numbering  
continues from the last number used.  
Off (Do not  
continue  
numbering)  
File numbering is assigned, from RIMG0001.jpg to RIMG9999.  
jpg, for each SD memory card. When the file name reaches  
RIMG9999, no more data can be recorded to that card.  
Note----------------------------------------------------------------------------------  
• This option applies only to memory cards. The names of photos in internal  
memory consist of“RIMG”and a four-digit number.  
• When images are transferred to a computer using DL-10 (G P.155), the file  
being transferred is renamed and saved.  
Caution------------------------------------------------------------------------------  
When the file name reaches RIMG9999 or R9999999, no more files can be saved.  
In this case, move image data from the SD memory card to the memory of the  
computer or a storage medium, and then format the SD memory card.  
8
Date Settings  
G
P.30  
Set the camera clock.  
Note----------------------------------------------------------------------------------  
• If the battery is removed for more than three days, the date and time settings  
will be lost. These settings must be made again.  
• To retain the date and time settings, load a battery with adequate remaining  
power for more than ten hours.  
(
)
Language/N  
*
G
P.29  
You can change the language displayed on the screen.  
Video Out Mode (*)  
You can view your still images and movies on a television screen by connecting  
your camera to a television with the AV cable that came with your camera. Select  
from NTSC (used in North America, the Caribbean, parts of Latin America, and some  
East Asian countries) and PAL (used in the United Kingdom and much of Europe,  
Australia, New Zealand, and parts of Asia and Africa). SECAM is not supported.  
(
) The default setting varies depending on where you purchased the camera.  
*
86  
CALS Pic Quality  
Choose picture quality and size options for CALS mode (G P.37).  
Start Date/Time  
Select [On] to display the current time and date when you turn the camera on and  
select shooting mode.  
Choose/Change Password  
G
P.90  
Choose a password or change the current password. Passwords restrict access to  
some camera functions.  
Password Protection  
G
P.92  
Restrict access to some or all camera functions. Select [Off] to allow unrestricted  
access.  
Password Validity Period  
Choose how long the camera can be used without re-entering the password. This  
option takes effect only when [Camera] or [Int. Memory] is selected for [Password  
Protection]. If [Off] is selected, the camera can only be accessed by re-entering the  
password.  
Power Button Hold Options  
If [On] selected, the POWER button must be pressed for at least two seconds to turn  
the camera on and for at least five seconds to turn the camera off.  
8
87  
Reg. My Settings  
Save current camera settings in [MY1] or [MY2]. Settings saved in [MY1]  
are recalled when the mode dial is rotated to T, those saved in  
[MY2] when the mode dial is rotated to U.  
Set the camera to the desired settings.  
1
2
Select [Reg. My Settings] in the setup menu (G P.82) and  
press the $ button.  
• A confirmation message appears.  
Select [MY1] or [MY2] and press the MENU/OK button.  
• The current camera settings are registered and the display returns to  
the setup menu.  
3
• If you do not want to register them, press the DISP. button.  
Settings Saved in [Reg. My Settings]  
Shooting mode  
(V/5/T/U/W)  
Focal distance used in Manual  
Zoom position  
Macro  
WB-BKT  
Time Exposure  
Camera Shake Correction  
Date Imprint  
8
Flash Mode  
Scene mode  
Exposure Compensation  
White Balance  
Self-Timer  
ISO Setting  
DISP. mode  
Edit Detection  
Density  
Stepped Zoom  
Picture Quality/Size  
Focus  
Digital Zoom Image  
Level Setting  
Exposure Metering  
Continuous Mode  
Image Settings  
Auto Bracket  
Grid Guide Display Options  
Shooting Info. Display Frame  
CALS Pic Quality  
88  
Digital Zoom Image  
If [Normal] (the default option) is selected for [Digital Zoom Image] ,  
digital zoom will enlarge image data from the center of the frame to  
create a picture at the current image size, creating a slightly grainy  
image. To record pictures taken with digital zoom at actual size, select  
[Auto Resize]. The size at which the image will be recorded varies with  
the zoom ratio.  
Auto resize takes effect if you keep the z  
button pressed when the zoom bar is full.  
The size will then change each time the  
z button is pressed; the current size is  
displayed above the zoom bar.  
The auto resize zoom is enabled when l4 : 3F or l4 : 3N is selected  
for [Picture Quality/Size] (G P.63), and the digital zoom is enabled in  
other cases.  
8
Zoom Magnification and Recorded Image Size  
Picture Quality/Size  
l4 : 3 F/l4 : 3 N  
e4 : 3 F  
c4 : 3 F  
a4 : 3 F  
Zoom Magnification Focal Length (*)  
1.0 ×  
1.5×  
2.0×  
3.1×  
6.3 ×  
140 mm  
210 mm  
270 mm  
430 mm  
870 mm  
z4 : 3 F  
(*) Equivalent to that on a 35mm camera  
Caution---------------------------------------------------------------------------------  
• Regardless of the option selected, normal digital zoom is used when [Skew  
Correct Mode] is selected in scene mode.  
• Fine picture quality is used for all photographs recorded using [Auto Resize],  
regardless of the option currently selected for [Picture Quality/Size].  
89  
Choose/Change Password  
Choose the password that must be entered  
to access password-protected settings  
(G P.92). The password can be a barcode  
or a phrase entered via an on-screen  
keyboard.  
Note-------------------------------------------------------------------------------------  
The current password is required to change an existing password.  
Barcode  
Frame the barcode in the picture display and  
press MENU/OK. If the camera can read the  
code, it will set the password to the barcode  
and return to the previous menu. Press DISP.  
to exit without entering a new password.  
8
Note-------------------------------------------------------------------------------------  
The camera can read linear and matrix barcodes.  
Linear  
Matrix (QR)  
Matrix (PDF417)  
Caution---------------------------------------------------------------------------------  
You will be prompted to enter a password  
whenever you attempt to access functions  
protected using [Password Protection]. Frame  
the password barcode in the picture display and  
press MENU/OK. If the barcode is incorrect, a  
message will be displayed; select [Yes] to return  
to the password entry dialog.  
90  
Keyboard  
Enter a password of up to 16  
Password area  
1
characters.  
• Highlight characters using !, ", #,  
or $ and press MENU/OK to enter the  
highlighted character at the current  
cursor position (to delete the character  
at the current cursor position, select  
[Delete]). Press ADJ./MEMO when  
entry is complete (to exit without  
changing the password, press DISP.).  
Keyboard area  
Re-enter the password.  
2
• A confirmation dialog will be displayed; re-enter the password as  
described above to save the password and return to the setup menu.  
If the passwords do not match, a message will be displayed and the  
camera will return to the password entry dialog.  
Caution---------------------------------------------------------------------------------  
You will be prompted to enter a password  
whenever you attempt to access functions  
protected using [Password Protection]. Enter  
the password as described in Step 1, above. If  
the password is incorrect, a message will be  
displayed; select [Yes] to return to the password  
entry dialog.  
8
91  
Password Protection  
Choose the camera functions protected with the password selected  
using [Choose/Change Password] (G P.90). Five options are available.  
Off  
Choose this option to allow unrestricted access to all camera functions.  
No password is required.  
Camera  
You will be prompted to enter a password when the camera is turned  
on. The camera can not be used until you enter the password; if an  
incorrect password is entered, the camera will turn off automatically.  
Int. Memory  
If a memory card is inserted, this option is the same as [Camera]. If no  
memory card is inserted, you will be prompted to enter a password  
before viewing the images in internal memory (no pictures will be  
displayed until the correct password is entered) and when connecting  
the camera to a computer or printer (if an incorrect password is  
entered, the camera will turn off).  
8
Caution---------------------------------------------------------------------------------  
You will also be prompted to enter a password if you select [Format [Internal  
Memory]] after entering an incorrect password. Entering the correct password  
will allow you to format internal memory; entering an incorrect password will  
cause the camera to exit without formatting internal memory.  
92  
SD WORM  
No password is required when SD WORM cards (G P.24) are used. If  
no memory card is inserted or another type of card is used, you will be  
prompted to enter a password when the camera is turned on. Entering  
an incorrect password will cause the camera to turn off.  
Menus  
A password is required to display the camera menus. The menus and  
ADJ. mode can not be used until the correct password is entered.  
Lost Passwords -----------------------------------------------------------------------  
Do not forget your password. If you forget your password, contact one of the  
Ricoh offices listed on the back cover of this manual.  
8
93  
9
Camera Memo Menu  
Using the Menu  
Press the MENU/OK button.  
• The shooting menu (or the playback menu) appears.  
1
Press # to highlight the tab for the current menu.  
2
3
Press ! or " to highlight the  
camera memo menu tab.  
• The camera memo menu tab is  
third from the top.  
Indicates the range of displayed  
screens.  
Press $ to place the cursor in the camera memo menu.  
4
5
Press the !" buttons to select the  
desired item.  
9
• If the DISP. button is pressed at this  
point, the display returns to the screen  
shown in Step 3.  
• Press the " button at the bottom item  
to display the next screen.  
Press the $ button.  
• The menu item settings are displayed.  
6
7
8
Press the !" buttons to select the  
setting.  
Press MENU/OK, or press # and  
then MENU/OK.  
• The camera memo menu will close and  
the camera will return to shooting or  
playback.  
• Pressing the # button in Step 8 confirms the setting and the display  
returns to the screen shown in Step 5.  
94  
Camera Memo Menu Options  
Camera Memo Mode  
“Software User Guide”  
G
P.28  
Choose from the following options:  
Available Settings Description  
Mode1  
Mode2  
Choose a separate description for each item.  
Choose from pre-selected combinations. Descriptions can not  
be selected for individual items.  
Memo Skip  
“Software User Guide”  
G
P.28  
When choosing memos with [Mode2] selected for [Camera Memo Mode], you can  
press and hold # or $ to skip memos with identical descriptions for a selected  
item. Choose from items 1 to 5.  
Note----------------------------------------------------------------------------------  
This option only takes effect when [Mode2] is selected for [Camera Memo Mode].  
Mark Memo Added to Photos  
When [On] is selected, [Memo Marking] will appear  
in the camera memo dialog for memos that have  
been added to photographs. Marking can be  
removed by pressing D in the camera memo dialog  
or by selecting [Remove Memo Marking].  
9
F
Note----------------------------------------------------------------------------------  
This option only takes effect when [Mode2] is selected for [Camera Memo Mode].  
Remove Memo Marking  
Remove [Memo Marking] marking from the camera memo dialog for memos that  
have been added to photos taken with [On] selected for [Mark Memo Added to  
Photos].  
Memo Warning  
If [On] is selected, a warning will be displayed and the shutter release will be  
disabled if you attempt to take a photograph with the description for one or more  
memo items set to [No Setting]. The shutter release can be enabled by choosing a  
description for the affected items.  
Note----------------------------------------------------------------------------------  
This option has no effect when [Mode2] is selected for [Camera Memo Mode] or  
[On] is selected for [Camera Memo 1 Auto Delete].  
95  
Display Memo at Startup  
Select [On] to display the camera memo dialog when the camera is turned on.  
Note----------------------------------------------------------------------------------  
This option is only available if a memo list has been transferred to the camera.  
Memo Increment  
“Software User Guide”  
G
P.32  
If [On] is selected, numbers that appear at the end of memo descriptions can be  
increased or decreased by pressing ! or ".  
Note----------------------------------------------------------------------------------  
This option only takes effect when [Mode1] is selected for [Camera Memo Mode].  
Camera Memo Imprint  
Select [On] to stamp the first three memo items on photographs.  
Note----------------------------------------------------------------------------------  
• Only the first ten letters of the item name and first 32 letters of the description  
will appear on photographs. Only the first 31 letters (including the item name  
and the colon that appears between the item name and the description) will  
appear on photographs taken with [z4:3F] selected for [Picture Quality/  
Size].  
• This option has no effect when [Mode3] is selected for [Barcode Mode].  
Camera Memo 1 Auto Delete  
If [On] is selected, the description for the first memo item will automatically be set  
to [No Setting] when the camera is turned on, a photograph is taken, or a memo  
list is transferred to the camera. A warning will be displayed and the shutter release  
will be disabled if you attempt to take a photograph with the description for the  
first item still set to [No Setting]. The shutter release can be enabled by choosing a  
description for the first item.  
9
Note----------------------------------------------------------------------------------  
This option has no effect when [Mode2] is selected for [Camera Memo Mode].  
96  
Barcode Type  
Choose from the following options:  
Available Settings  
Auto  
Description  
The camera automatically detects the barcode type.  
Linear  
Use for linear barcodes. The following types are supported:  
EAN-13/8 (JAN-13/8), UPC-A/E, UPC/EAN (with add-ons),  
Interleaved 2 of 5, CODEBAR (NW-7), CODE 39, CODE 93,  
CODE 128 TYPE C, GS1-128 (EAN-128), and RSS (GS1  
DataBar).  
QR Code, Micro QR  
Code, DataMatrix,  
When scanning matrix barcodes, choose the option that  
corresponds to the type of barcode that will be scanned.  
PDF417, Micro PDF417,  
MaxiCode, EAN.UCC  
Note----------------------------------------------------------------------------------  
• The camera can read linear barcodes of up to 32 digits and matrix barcodes of  
up to 2400 digits.  
• Voice memos are not available with matrix barcodes.  
Barcode Mode  
“Software User Guide”  
G
P.36  
Choose where barcode data are stored.  
Available Settings Description  
Mode1  
The barcode is stored in the memo list as a temporary  
description for the first item. This description is overwritten each  
time a barcode is read.  
9
Mode2  
The first barcode read is stored in the memo list as a temporary  
description for the first item, the second barcode as a  
temporary description for the second item, the third barcode  
as a temporary description for the third item, and the fourth  
barcode as a temporary description for the fourth item. These  
descriptions are overwritten in turn as new barcodes are read.  
Mode3  
This option only takes effect in shooting mode. Up to fifty  
barcodes can be stored in the memo list as temporary  
descriptions for the first item. These data can be viewed in the  
camera memo dialog before shooting but can not be changed  
and are deleted after a photograph is taken.  
Scan Time  
Choose the maximum time the camera will wait for a barcode to be scanned.  
Scanning will be interrupted if a barcode is not read in the specified time.  
Note----------------------------------------------------------------------------------  
If [27 seconds] or [30 seconds] are selected when a BR-1 barcode reader  
(available separately) is connected, the scan delay will be set to 25.5 seconds.  
97  
10 Expanded Settings Menu  
Using the Menu  
Press the MENU/OK button.  
• The shooting menu (or the playback menu) appears.  
1
Press # to highlight the tab for the current menu.  
2
3
Press ! or " to highlight the  
expanded settings menu tab.  
• The expanded settings menu tab is  
fourth from the top.  
Indicates the range of displayed  
screens.  
Press $ to place the cursor in the expanded settings menu.  
4
5
Press the !" buttons to select the  
desired item.  
• If the DISP. button is pressed at this  
point, the display returns to the screen  
shown in Step 3.  
10  
• Press the " button at the bottom item  
to display the next screen.  
Press the $ button.  
• The menu item settings are displayed.  
6
7
8
Press the !" buttons to select the  
setting.  
Press MENU/OK, or press # and  
then MENU/OK.  
• The expanded settings menu will close  
and the camera will return to shooting  
or playback.  
• Pressing the # button in Step 8 confirms the setting and the display  
returns to the screen shown in Step 5.  
98  
Note-------------------------------------------------------------------------------------  
For some functions, the setting selection method may differ from what is  
explained here. For detailed operation, see the explanation of each function.  
Expanded Settings Menu Options  
GPS Datum  
Choose the geodetic system used when a GP-1 or Bluetooth®-equipped GPS unit  
is connected.  
Available Settings Description  
TOKYO  
The system in common use in Japan.  
WGS-84  
The system in common use internationally.  
GPS Disp Mode  
Choose the format used to display GPS data from a GP-1 or Bluetooth®-equipped  
GPS unit.  
Available Settings Description  
LAT/LON  
UTM  
MGRS  
ALL  
Show latitude and longitude.  
Use Universal Transverse Mercator projection (UTM).  
Use the Military Grid Reference System (MGRS).  
Display all of the above.  
GPS Lock  
N: 035˚  
If [On] is selected when a GP-1 or Bluetooth®-  
equipped GPS unit is used, the $ button can be used  
to disable or enable the reception of new GPS data.  
10  
Caution------------------------------------------------------------------------------  
• If [2Touch] is selected for [Quick Send Mode] (G P.104), files can not be  
transmitted when [GPS Lock] is on.  
• Changing the option selected for [GPS Datum] or [GPS Data Select] ends GPS  
lock.  
99  
GPS Data Select  
G
P.136  
Choose which device is used when both a GP-1 and a Bluetooth®- equipped GPS  
unit are connected. Choose [GPS Options] to use the GP-1, [Bluetooth] to use the  
Bluetooth®-equipped GPS unit.  
Note----------------------------------------------------------------------------------  
If a GP-1 is connected, the compass heading is available even when [Bluetooth]  
is selected.  
GPS Track Time  
Choose the interval at which GPS log data are written to the memory card. GPS data  
will not be logged if [Off] is selected.  
Note----------------------------------------------------------------------------------  
• GPS logs are stored in the“GPSLOG”folder as files named using the current date  
plus a two-digit file number followed by the extension“.LOG”.  
• A new log file is created if the date has changed since the last log file was  
created or when the current log file exceeds 500KB in size.  
• Log files are not created if the memory card is locked (G P.25), an SD WORM  
card is used, or the memory card is full or not inserted. No warning is displayed  
if a log can not be created because the card is full.  
• Logs can be deleted using the [Delete GPS Log] option. Formatting the  
memory card using the [Format [Card]] option (G P.83) in the setup menu  
(G P.82) does not delete GPS log files.  
Delete GPS Log  
Highlight [Yes] and press MENU/OK to delete all GPS log files.  
Note----------------------------------------------------------------------------------  
• GPS logs can not be deleted if the memory card is locked (G P.25).  
10  
• Formatting the memory card using the [Format [Card]] option (G P.83) in the  
setup menu (G P.82) does not delete GPS log files.  
Compass Heading  
Choose the format used to display compass headings  
received from GP-1 or Bluetooth®-equipped GPS  
units that supply compass data.  
Degrees Points  
Available Settings Description  
Cardinal  
Degree  
The heading is displayed using points of the compass.  
The heading is displayed using both points and degrees.  
100  
Compass Calibration  
If a GP-1 is connected, its compass can be calibrated  
by highlighting [Yes], pressing MENU/OK, and then  
holding the camera in one hand and slowly moving it  
through a large figure eight while rotating your wrist.  
Each pass should take from five to eight seconds; a  
beep will sound if calibration is successful, a warning  
buzzer if it is not. Press DISP. to cancel and exit to  
the expanded settings menu before calibration is  
complete.  
GPS Data Imprint  
Select [On] to record GPS data with photographs taken while a GP-1 or Bluetooth®-  
equipped GPS unit is connected. GPS data are recorded in the format selected for  
[GPS Disp Mode] (G P.99). GPS data are not recorded when [Off] is selected or  
when GPS data are unavailable.  
UTC Data Imprint  
Select [On] to record the time provided by the GPS unit with photographs taken  
while a GP-1 or Bluetooth®-equipped GPS unit is connected. The time is not  
recorded when [Off] is selected or when GPS data are unavailable.  
Heading Data Imprint  
If a GP-1 or a Bluetooth®-equipped GPS unit that supplies compass data is  
connected, select [On] to record the compass heading in the format selected for  
[Compass Heading] (G P.100). The compass heading is not recorded when [Off] is  
selected or when GPS data are unavailable.  
Range Finder Mode  
10  
Choose how data acquired from a Bluetooth®-equipped laser range finder (available  
separately from third-party suppliers) are handled.  
Available Settings Description  
Mode1  
Mode2  
Mode3  
Range data always appear in the picture display.  
Range data are displayed until a photograph is taken.  
Photos are taken automatically as range data are acquired.  
101  
Communication Mode  
Choose whether data transmitted using [File Send] (G P.74) and quick send  
(G P.104) are sent via wireless LAN ([W-LAN]) or Bluetooth® ([Bluetooth]).  
Import Communication Setting  
G
P.125  
Highlight [Yes] and press MENU/OK to load a host list previously created and  
transmitted to the camera using the supplied ST-10 software (G P.123). Host lists  
are required when sending files from the camera to a computer via a wireless LAN  
(G P.112).  
Send To  
View, edit, or choose a host from a host list.  
Note----------------------------------------------------------------------------------  
If you do not select a host using this option before connecting to a wireless LAN,  
the camera will attempt to connect to the first host in the list when pictures are  
sent with [Off] selected for [Send Status] or quick send is used with [1Touch]  
selected for [Quick Send Mode] (G P.109).  
Send Status  
Select [On] to select a host every time pictures are sent, [Off] to send pictures to the  
host selected with [Send To]. Choose [Off] if you always use the same host.  
Simple Connection  
G
P.128  
Use a simple connection method to connect to the wireless host or access point  
when sending data via wireless LAN.  
10  
102  
Bluetooth Pass Key  
Enter a password for Bluetooth® connections, allowing the camera to supply the  
password automatically when it connects to a password-protected Bluetooth®  
device.  
Note----------------------------------------------------------------------------------  
• For information on using passwords with a Bluetooth® device, see the  
documentation provided with the equipment.  
• The camera supports passwords of up to 16 characters.  
• If this option is not used, the password must be entered manually each time  
the camera connects to the device.  
• The camera can store only one password at a time. When connecting to  
multiple devices, ensure that they share the same password.  
• Before changing an existing password, enter the current password and press  
MENU/OK.  
Bluetooth Search Count  
Choose the maximum number of Bluetooth® devices (1–10) that will be detected by  
the camera.  
Bluetooth Auto Conn  
G
P.138  
If [On] is selected when the camera is turned on, the camera will automatically  
connect to any Bluetooth® devices to which it was connected when it was turned  
off.  
Bluetooth Serial  
G
P.137  
Lists the Bluetooth® devices detected by the camera. Press ! or " to highlight a  
device and press MENU/OK to connect.  
Bluetooth Master/Slave  
10  
Choose [Master] to allow the camera to be used with multiple Bluetooth® devices  
simultaneously, [Slave] to allow it to be used with only one device at a time.  
Image File Size  
Images will automatically be converted to the selected size during transmission.  
Select [No Alter] to send images at their original size.  
Caution------------------------------------------------------------------------------  
Images are automatically converted to a supported size when sent to BIP-profile  
Bluetooth® devices; as a result, images may not be converted to the size selected  
with [Image File Size].  
103  
Auto Delete  
Select [On] to automatically delete files from the camera after they have been  
transmitted to a computer.  
Quick Send Mode  
G
P.108  
Upload pictures to a computer as they are taken.  
Bluetooth Profile  
Choose a profile for connection to Bluetooth® devices.  
Available Settings Description  
OPP/BIP  
OPP  
Use BIP if device does not support OPP; otherwise use OPP.  
Use OPP (Object Push Profile).  
BIP  
Use BIP (Basic Imaging Profile).  
Custom Help  
G
P.59  
Select [On] to enable custom help.  
Admin Pass Key  
Choose a password for custom help.  
Note----------------------------------------------------------------------------------  
• The password for custom help is not the same as the password selected for  
[Choose/Change Password] (G P.90).  
• See“Keyboard”(G P.91) for information on entering a password. Barcode  
readers can not be used.  
Caution------------------------------------------------------------------------------  
Do not forget your password. If you forget your password, contact one of the  
Ricoh offices listed on the back cover of this manual.  
10  
Admin Mode [Regist]  
G
P.59  
Copy custom help (JPEG image files) from a memory card to internal memory.  
Admin Mode [Delete]  
G
P.61  
Delete selected custom help files.  
104  
11 Bluetooth®  
The camera supports both Bluetooth® and wireless LAN for wireless  
data transfer. Bluetooth® can be used to connect simultaneously to  
multiple computers and other devices. Before using Bluetooth®, select  
[Bluetooth] for [Communication Mode] (G P.102) in the expanded  
settings menu (G P.98).  
Bluetooth® Connections  
Complex settings are not required to transfer images via Bluetooth®.  
Select [Bluetooth] for  
[Communication Mode].  
1
• Select [Bluetooth] for [Communication  
Mode] (G P.102) in the expanded  
settings menu (G P.98).  
Transfer images.  
2
• Transfer images using quick send (G P.104) or the [File Send]  
option (G P.74) in the playback menu (G P.72). The camera will  
automatically detect potential hosts; select a host to begin transfer  
(a password may be required).  
Caution---------------------------------------------------------------------------------  
• Bluetooth® has a maximum range of about 10 m (33 ft.); ensure that there are  
no obstacles between the two devices.  
11  
• The camera can communicate with devices that use the Basic Imaging Profile  
(BIP) or Object Push Profile (OPP). Consult the documentation provided with  
the Bluetooth® device.  
• Movies can not be transferred via Bluetooth®.  
105  
Entering a Password  
If an authentication key, or password, is  
required for connection to a Bluetooth®  
device, a message will be displayed. Enter a  
password as described below.  
Press MENU/OK.  
• An on-screen keyboard will be displayed.  
1
Enter the password.  
2
• Enter a password as described on  
P.91 (for information on selecting a  
password, consult the documentation  
provided with the host device). If you  
do not enter the correct password  
within 30 seconds, an error message  
will be displayed; press MENU/OK to try  
again.  
Press MENU/OK.  
• Press MENU/OK to begin transfer.  
3
Note-------------------------------------------------------------------------------------  
• The camera supports passwords of up to 16 characters.  
11  
• The camera stores the password and performs authentication automatically  
when you next connect to the device; no further password entry is required.  
If desired, the password can be stored in the camera before the connection is  
made (G P.103).  
• If the Bluetooth® device displays a password-entry dialog before the camera,  
enter the password on the device first and then enter the same password on  
the camera.  
106  
Transferring Images During Playback  
(Bluetooth®)  
Images can be copied to Bluetooth® devices using the [File Send]  
option in the playback menu (G P.72).  
Select [File Send].  
1
• Select [File Send]. If you intend to copy  
only one picture, display the picture full  
frame before proceeding. Highlight  
[File Send] in the playback menu  
(G P.72) and press $ to display a list  
of devices (if this is the first time you  
have used Bluetooth®, a confirmation  
dialog will be displayed; highlight [Yes] and press MENU/OK).  
Choose a host.  
2
• Press ! or " to highlight a device and  
press MENU/OK (to view a description  
of the highlighted device, press $; to  
remove the device from the list, press  
D). If the desired device does not  
appear, press ADJ./MEMO to refresh the  
list.  
Transfer images.  
3
• Highlight [Send One] (send only the  
current image) or [Send All] (copy all  
images), and press MENU/OK. Enter a  
password if prompted (G P.106). A  
progress indicator will be displayed.  
11  
Press MENU/OK when transfer is complete.  
• A message will be displayed when transfer is complete. Press MENU/  
OK to return to playback.  
4
Transferring Multiple Selected Images -----------------------------------------  
To transfer multiple selected images, select thumbnail view (G P.38) before  
selecting [File Send]. After choosing a device as described in Step 2, highlight still  
images and press MENU/OK to select or deselect. Press DISP. when your selection  
is complete. A confirmation dialog will be displayed; highlight [Yes] and press  
MENU/OK to transfer the selected images.  
107  
Skipping Steps 1 and 2--------------------------------------------------------------  
Once you have selected a host and password, the options in Step 3 can be  
displayed by pressing and holding DISP. during playback.  
Interrupting Transfer ---------------------------------------------------------------  
Pressing DISP., 6, or the shutter release button interrupts transfer.  
Note-------------------------------------------------------------------------------------  
Unless [BIP] is selected for [Bluetooth Profile] (G P.104) in the expanded settings  
menu (G P.98), images are transferred at the size currently selected for [Image  
File Size] (G P.103) in the expanded settings menu (G P.98). If [BIP] is selected  
and the image file size is larger than the maximum supported by the device,  
images will be resized to the maximum supported by the device.  
Transferring Images During Shooting  
(Bluetooth®)  
The [Quick Send Mode] option (G P.104) in the expanded settings  
menu (G P.98) can be used to transfer photographs as they are taken.  
Movies can not be transferred.  
Available Setting Description  
Off  
Photos are not uploaded during shooting.  
1Touch  
Press MENU/OK when a photo is displayed after shooting to  
upload it to a Bluetooth® device.  
2Touch  
Auto  
Press $ to display the most recent photo and press MENU/OK  
to begin upload. Not available when [On] is selected for [GPS  
Lock] (G P.99).  
Photos are automatically uploaded at their original size as they  
are taken.  
11  
Caution---------------------------------------------------------------------------------  
Photos are not uploaded in scene mode (G P.52) or if [On] is selected for  
[Continuous Mode] (G P.64) in the shooting menu.  
Note-------------------------------------------------------------------------------------  
• Before shooting, confirm that the host device is on.  
• The [Auto Delete] option (G P.104) in the expanded settings menu (G P.98)  
can be used to automatically delete photos from the camera after transfer.  
108  
Interrupting Transfer/Terminating the Connection -------------------------  
To interrupt transfer, rotate the mode dial or press DISP., 6, or the shutter release  
button. To interrupt transfer and terminate the connection, select playback mode  
or turn the camera off.  
Choosing a Host----------------------------------------------------------------------  
Photos are automatically uploaded to the device last selected for [File Send]  
(G P.74) in playback mode. Use [File Send] to choose a different device.  
One-Touch Transfer  
When [1Touch] is selected for [Quick Send Mode], the MENU/OK  
button can be used when a photo is displayed after shooting to  
upload it to the device currently selected for [File Send]. The photo is  
not uploaded if the button is not pressed in the time selected for [LCD  
Confirmation Time] (G P.84) in the setup menu (G P.82); longer  
times are recommended.  
A Bluetooth® antenna icon is displayed  
while the camera is connected to the  
device; when transfer is complete, the  
camera will return to shooting mode  
without terminating the connection. The  
connection can be terminated by selecting  
playback mode or turning the camera off.  
Note-------------------------------------------------------------------------------------  
• Photos can not be uploaded if: a device has not been selected using [File Send]  
(G P.74), [Off] is selected for [LCD Confirmation Time], [On] or [WB-BKT] is  
selected for [Auto Bracket], or the option selected for [Picture Quality/Size] is  
larger than the size supported by the host when [BIP] is selected for [Bluetooth  
Profile] (G P.104) in the expanded settings menu (G P. 9 8 ) .  
11  
• Images are not resized during transfer, regardless of the option selected for  
[Image File Size] (G P.103) in the expanded settings menu (G P.98).  
109  
Two-Touch Transfer  
To upload your most recent photo:  
Press $.  
1
• A confirmation dialog will be displayed. (If this is the first time you  
have used two-touch transfer, you will be asked if you wish to  
choose a host; highlight [Yes] and press MENU/OK to display a list of  
Bluetooth® devices. Press ! or " to highlight a device and press  
MENU/OK. If the desired device does not appear, press ADJ./MEMO  
to refresh the list.)  
Press MENU/OK to begin transfer.  
• Enter a password if prompted  
2
(G P.106). A progress indicator is  
displayed during transfer. A Bluetooth®  
antenna icon is displayed while the  
camera is connected; when transfer  
is complete, the camera will return to  
shooting mode without terminating  
the connection. The connection can be terminated by selecting  
playback mode or turning the camera off.  
Note-------------------------------------------------------------------------------------  
• Two-touch transfer can not be used when [On] is selected for [GPS Lock]  
(G P.99) in the expanded settings menu (G P. 9 8 ) .  
• Unless [BIP] is selected for [Bluetooth Profile] (G P.104) in the expanded  
settings menu (G P.98), images are transferred at the size currently selected  
for [Image File Size] (G P.103) in the expanded settings menu (G P.98). If  
[BIP] is selected and the image file size is larger than the maximum supported  
by the device, images will be resized to the maximum supported by the device.  
11  
110  
Auto Transfer  
Select [Auto] to automatically upload photos as they are taken.  
Note-------------------------------------------------------------------------------------  
• Photos can not be uploaded if a device has not been selected using [File Send]  
(G P.74) or if the option selected for [Picture Quality/Size] is larger than the size  
supported by the host when [BIP] is selected for [Bluetooth Profile] (G P.104) in  
the expanded settings menu (G P.98).  
• Images are not resized during transfer, regardless of the option selected for  
[Image File Size] (G P.103) in the expanded settings menu (G P.98).  
11  
111  
12 Wireless Networks  
Pictures can be uploaded from the camera over a wireless Local Area  
Network (LAN). Before accessing a wireless network, select [W-LAN]  
for [Communication Mode] (G P.102) in the expanded settings menu  
(G P.98).  
Connecting to a Wireless Network  
Configure the host device (G P.113).  
1
• Use the supplied ST-10 software to configure the host ftp server.  
If desired, the supplied SR-10 software can be used to create an  
SR-10 ftp server on your computer exclusively for use by the G700SE  
(G P.120).  
Create a host list (G P.123).  
• Use ST-10 to create a host list containing connection information for  
the hosts you configured in Step 1.  
2
Copy the host list to the camera (G P.123).  
3
• Connect the camera to the computer using the supplied USB cable  
and transfer the host list to internal memory, or use a memory card  
to copy the host list to the camera (G P.125). Host lists can be  
edited on the camera after transfer (G P.127).  
Select [W-LAN] for [Communication Mode].  
• Select [W-LAN] for [Communication Mode] (G P.102) in the  
4
expanded settings menu (G P.98).  
12  
Transfer images.  
5
• Use quick send (G P.104) or the [File Send] option (G P.74) in  
the playback menu (G P.72) to transfer images to a host selected  
from a list displayed when transfer begins. If desired, the host can  
be selected in advance using the [Send To] option (G P.102) in the  
expanded settings menu (G P.98).  
112  
Caution---------------------------------------------------------------------------------  
• The camera’s wireless transmitter has a maximum range of about 30 m (100 ft.);  
ensure that there are no obstacles between the two devices.  
• The supplied ST-10 software (available for Windows only) is required for  
connection to a wireless LAN.  
Configuring the Host  
Before images can be transferred to a host computer or other  
device over a wireless network, a host list containing the necessary  
connection information must be copied to the camera. The supplied  
ST-10 software is used to configure the host computer for transfer.  
Note-------------------------------------------------------------------------------------  
See P.151 for information on installing ST-10.  
Start ST-10.  
1
• Start ST-10. In the Windows start menu, select [All Programs] >  
[Programs] > [DC Software] > [ST-10].  
Click [All Detailed Setups].  
• The ST-10 window will be displayed.  
Click [All Detailed Setups].  
2
12  
113  
Click the desired tab.  
3
• In the [Detailed Setups for selections]  
dialog, choose from the following  
tabs:  
- Network: Enter an IP address.  
- Wireless LAN: Adjust wireless LAN  
settings.  
- FTP Send: Adjust ftp settings.  
- Dial-up/Mail Config./Address  
Book: Not required; the camera  
does not support dial-up  
connections or e-mail.  
Note-------------------------------------------------------------------------------------  
• If the computer is not currently configured for ftp, use the supplied SR-10  
software to create an ftp server (G P.120).  
• Advanced settings for some options can be accessed by clicking [Detail].  
Click [Add].  
4
• Click the [Add] button under [Setup  
Name] to display the [New Name for  
the Setup] dialog.  
Enter a name.  
• Enter a name for the new  
configuration and click [OK].  
5
6
Adjust settings.  
• Adjust settings as described on P.116.  
12  
The configuration currently selected in the [Setup Name] list can be  
renamed by clicking [Rename] or deleted by clicking [Delete]. Click  
[Apply] to save changes.  
114  
Adjust settings in the remaining tabs.  
• Repeat Steps 3–6 to adjust settings in the remaining tabs.  
7
8
Save settings and exit.  
• Click [OK] to save changes and return to the ST-10 window, and then  
click [OK] to exit ST-10.  
Caution---------------------------------------------------------------------------------  
Consult the system administrator for information on network settings.  
12  
115  
Detailed Setups Tab Settings  
[Network] tab  
Item Name  
Description  
Host Setup  
Host Name  
These settings are not required when using this  
camera.  
Camera Password  
Automatically retrieves its  
IP address  
Select this to retrieve an IP address automatically for  
the camera.  
Use the following IP address Select this to use a fixed IP address, and then enter the  
information below.  
IP address  
Subnet Mask  
Default Gateway  
[IP address]  
Fixed IP address for the camera  
[Subnet Mask]  
Usually enter 255.255.255.0.  
[Default Gateway]  
IP address of an Internet-connected computer  
Automatically retrieves the Select this to retrieve the address automatically from  
address from the DNS server the DNS server.  
Use the following DNS  
server addresses  
Primary DNS Server  
Secondary DNS Server  
Select this to use a fixed DNS server address, and then  
enter the information below.  
[Primary DNS Server]  
Primary DNS server address of your Internet service  
provider  
[Secondary DNS Server]  
Secondary DNS server address of your Internet  
service provider  
12  
116  
[Wireless LAN] tab  
Note-------------------------------------------------------------------------------------  
Wireless LAN settings do not require adjustment when the simple connection  
option is used (G P.128).  
Item Name  
Description  
Connection Method  
Select from the following connection methods.  
[Infrastructure]  
Connection method for communication through  
routers and access points  
[AdHoc]  
Connection method for communication between  
slave devices  
ESS-ID  
A wireless LAN enables communication between a  
master device and a slave device having the same  
ESS-ID. Enter the same ESS-ID as the master device.  
When several access points are in use, a channel is  
set to each access point. Select the channel of the  
access point.  
Communication Channel  
[Auto]  
Select this if [Connection Method] is set to  
[Infrastructure] and there is only one access point.  
[1-13]  
If [Connection Method] is set to [Infrastructure] and  
there are several access points or if [Connection  
Method] is set to [AdHoc], select the channel you  
want to use.  
Cryptography  
Select from the following encryption methods.  
[None]  
12  
No encryption is used.  
[WEP]  
This can be selected when [Connection Method] is  
set to either [Infrastructure] or [AdHoc].  
[AES]  
This can be selected only when [Connection  
Method] is set to [Infrastructure].  
[TKIP]  
This can be selected only when [Connection  
Method] is set to [Infrastructure].  
117  
Item Name  
Description  
Network Key  
Enter the security key. Select a key type from [String]  
and [Hex] and enter an encryption key in the box.  
[String]  
If [WEP] is selected for [Cryptography], enter  
an encryption key of 5 or 13 characters. Entering a 5-  
character string uses 40-bit encryption, and entering  
a 13-character string uses 128-bit encryption.  
If [AES] or [TKIP] is selected, enter an  
encryption key from 8 to 63 characters.  
[Hex]  
If [WEP] is selected for [Cryptography], enter  
a ten-character (40 bit) or 26-character (128 bit) key.  
If [AES] or [TKIP] is selected, enter a 64-  
character key.  
Authentication  
[Open System]  
This can be selected only when [Cryptography] is  
set to [None] or [WEP]. This authentication does not  
use WEP keys.  
[Shared Key]  
This can be selected only when [Cryptography] is set  
to [None] or [WEP]. This authentication compares  
the WEP keys of different devices.  
[WPA-PSK]  
This can be selected only when [Cryptography] is set  
to [AES] or [TKIP].  
[WPA2-PSK]  
This can be selected only when [Cryptography] is set  
to [AES] or [TKIP].  
12  
[FTP Send] tab  
Item Name  
Description  
Server Name  
Enter the name or IP address of the ftp server to which  
images will be uploaded. If you are using the SR-10  
server (G P.120), enter the IP address.  
Enter a user name and password for the ftp server to  
which images will be uploaded. Not required if you  
are using the SR-10 server (G P.120).  
Choose the destination folder for images uploaded to  
the ftp server.  
User Name and Password  
Specify Folder  
118  
Item Name  
Description  
Does not send file whose  
name already exists  
If this option is selected, images will not be uploaded  
if an image with the same filename already exists  
in the destination folder (SR-10 servers (G P.120)  
ignore this setting; during upload, images are  
renamed as necessary to avoid duplication as  
described on P.122). If this option is not selected,  
images in the destination folder will be overwritten by  
images with the same filename.  
PASV  
Select this option to connect to the ftp server in PASV  
mode. Choose this option when you are unable to  
connect to an ftp server that is behind a firewall.  
Note-------------------------------------------------------------------------------------  
The camera does not support dial-up connections or e-mail, and there is  
consequently no need to adjust the settings in the [Dial-up], [Mail Config.], and  
[Address Book] tab.  
12  
119  
Configuring a G700SE-only FTP Server  
If the computer is not currently configured for use as an ftp server,  
the supplied SR-10 software can be used to create an SR-10 ftp server  
exclusively for use by this camera.  
Caution---------------------------------------------------------------------------------  
SR-10 ftp servers created using the supplied SR-10 software can be used only for  
upload from this camera. Other ftp clients can not connect, and images can not  
be downloaded to the camera.  
Note-------------------------------------------------------------------------------------  
See P.151 for information on installing SR-10.  
Start SR-10.  
1
• In the Windows start menu, select  
[All Programs] > [Programs] >  
[DC Software] > [SR-10]. The SR-10  
window will be displayed.  
12  
120  
Adjust settings.  
2
1
2
3
4
Specify: Choose a destination folder. Choose [Server] to upload  
images to the folder listed in the [Folder name] text box, [Camera]  
to upload images to the folder selected in the [FTP Send] tab of  
the host list, or [Server+Camera] to upload images to a sub-folder  
created under the folder listed in the [Folder name] text box using  
the name selected in the [FTP Send] tab of the host list (see below).  
1
Folder named in [Folder Name] text box  
Folder named in [Camera] text box  
Folder name: Enter the name of the destination folder or click the  
folder icon to navigate to the desired folder. Note that the folder  
is not created automatically; if necessary, create a folder with the  
desired name.  
2
Log file name: To create a transmission log, enter a name and path  
for the log file.  
PASV Mode Port Number: Enter the port number used for  
connection to the ftp server when [PASV] is selected in the ST-10  
[FTP Send] tab.  
3
4
12  
Click [Apply].  
• Click [Apply] to save changes.  
3
4
Click [Quit].  
• Click [Quit] to exit SR-10.  
121  
Uploading Images to the SR-10 Server  
To upload images to the SR-10 server, transfer the host list to the  
camera and then follow the steps below.  
Start SR-10.  
1
• In the Windows start menu, select [All Programs] > [Programs] >  
[DC Software] > [SR-10].  
Click [Start].  
2
• The SR-10 window will be displayed;  
click [Start] to start the ftp server. The  
computer is now ready to receive  
images from the camera. To hide the  
SR-10 window during upload, click  
[Hide]. SR-10 can be displayed again  
by clicking the SR-10 icon in the  
taskbar.  
Upload images.  
3
• Images are uploaded to the selected folder (G P.121). See P.105 and  
112 for more information. Transfer status is displayed in the SR-10  
[Connections] list.  
Note-------------------------------------------------------------------------------------  
If the destination folder contains an image with the same name as an image  
uploaded from the camera, the image in the destination folder will be renamed  
by adding a suffix assigned in ascending order from -001 to -999 to the end of  
the file name. If an image with the same name and suffix already exists in the  
destination folder, it will be overwritten.  
12  
122  
Creating a Host List and Transferring It to  
the Camera  
Once hosts have been configured using ST-10, you can create a host  
list for transfer to the camera via USB.  
Note-------------------------------------------------------------------------------------  
The host list can also be saved on a computer, copied to a memory card, and then  
transferred to the camera (G P.125).  
Click [Add] or select an existing  
host.  
1
1
• To add a new host, click [Add]. To  
edit settings for an existing host,  
choose it from the pull-down  
menu.  
2
3
Adjust settings.  
2
3
Connection Method: Select [Wireless LAN] and choose wireless  
LAN settings from the pull-down menu. The settings selected in the  
[Wireless LAN] tab (G P.117) will be displayed.  
1
Network Setup: Choose a network from the pull-down menu. The  
settings selected in the [Network] tab (G P.116) will be displayed.  
Send Method: Select [Send via FTP]. The settings selected in the  
2
3
12  
[FTP Send] tab (G P.118) will be displayed.  
Add host configurations.  
• Repeat Steps 1 and 2 to add or edit other host configurations. The  
current configuration can be renamed by clicking [Rename] or  
deleted by clicking [Delete].  
Click [Apply].  
• Click [Apply] to save the host list.  
4
5
Connect the camera to the computer.  
• Turn the camera off and connect it to the computer using the  
supplied USB cable. The camera will turn on automatically.  
123  
Click [Transfer to Camera].  
6
• Enter the camera password when  
prompted and click [OK] to begin  
transfer. If you wish to update a host  
list already present on the camera,  
click [Yes] when prompted. If you did  
not click [Apply] in Step 4, you will  
also be prompted to save the host  
list; click [OK].  
Click [OK] when transfer is complete.  
• A message will be displayed when transfer is complete; click [OK].  
7
8
Exit ST-10.  
• Click [OK] in the ST-10 window to exit ST-10. Remove the camera  
from the system and disconnect the USB cable as described on P.156.  
Select [Import Communication  
Setting].  
9
• After turning the camera on, highlight  
[Import Communication Setting] in the  
expanded settings menu (G P.98) and  
press $. A confirmation dialog will be  
displayed.  
12  
124  
Select [Yes].  
10  
• Press $ to highlight [Yes] and press  
MENU/OK to copy the host list to  
internal memory and return to the  
expanded settings menu. If a host  
list is already present, a dialog will be  
displayed: select [Yes] to overwrite  
the existing list or [No] to exit to the  
expanded settings menu without  
updating the list.  
Note-------------------------------------------------------------------------------------  
• ST-10 saves network settings and the host list automatically when you exit the  
application. The most recently selected settings are displayed the next time you  
start ST-10.  
• The password entered in Step 6 is required when opening the host list in ST-10.  
• The ST-10 software supplied with this camera can not be used to open or  
transfer host lists created using ST-10 software supplied with earlier cameras.  
Recreate the host list using the version of ST-10 supplied with this camera.  
Reading a Host List from a Memory Card  
Host lists created with a computer can be copied to a memory card  
inserted in a card reader or card slot and then loaded into the camera’s  
internal memory.  
Caution---------------------------------------------------------------------------------  
Use a memory card that has been formatted in the camera.  
Click [Save in File].  
12  
1
• After creating a host list as described  
in Steps 1–4 on P.123, click [Save in  
File] to display the [Save As] dialog.  
125  
Choose a destination.  
2
3
• Navigate to the desired folder on the computer hard drive and  
enter a file name (note that although you can use any name, you  
will need to rename the file “SYSTEM.PRM”when copying it to the  
memory card in Step 5). Click [Save]. You will be prompted to enter a  
password.  
Enter a password and click [OK].  
• The host list will be saved to the selected destination and a message  
will be displayed.  
Note-------------------------------------------------------------------------------------  
Host lists stored on the computer hard drive can be opened for editing using the  
ST-10 [Open file] option. Enter the password you used in Step 3 when prompted.  
A warning will be displayed if the password is incorrect.  
Exit ST-10.  
• Click [OK] in the ST-10 window to exit ST-10.  
4
5
Copy the host list to the memory  
card.  
• Insert the memory card in a card reader  
or card slot and copy the host list to the  
“SYSTEM”folder on the memory card.  
Rename the file “SYSTEM.PRM”.  
Insert the memory card in the camera.  
Select [Import Communication Setting].  
• After turning the camera on, select [Import Communication Setting]  
in the expanded settings menu as described in Step 9 on P.124.  
6
7
12  
Caution---------------------------------------------------------------------------------  
Only one host list at a time can be read from a memory card.  
Note-------------------------------------------------------------------------------------  
The host list can also be transferred to the camera by direct USB connection  
(G P.123).  
126  
Viewing and Editing the Host List  
The camera can be used to view and edit the host list.  
Select [Send To].  
1
• After turning the camera on, highlight  
[Send To] in the expanded settings  
menu (G P.98) and press $ to display  
the host list.  
View settings.  
2
• Press ! or " to highlight items and press $ to view. Press DISP. to  
return to the previous display.  
Host list  
Category list  
Settings list  
Edit settings.  
3
4
• Highlight an entry in the settings list and press $. Edit the setting  
using the on-screen keyboard (G P.91) and press MENU/OK to save  
changes and return to the settings list. Repeat Steps 2–3 to select  
and edit additional settings.  
Return to the expanded settings menu.  
• Press MENU/OK to return to the expanded settings menu.  
12  
Caution---------------------------------------------------------------------------------  
Check the [Network Key] after editing [Crypt/Authentication] (G P.118). Note  
that if [AES/WPA-PSK], [AES/WPA2-PSK], [TKIP/WPA-PSK], or [TKIP/WPA2-PSK] was  
selected for [Cryptography] or [Authentication] in ST-10 (G P.117), changing  
the [Connection Method] to [AdHoc] automatically changes [Cryptography] to  
[None] and [Authentication] to [Open System].  
127  
Simple Connections for Wireless LANs  
Using the [Simple Connection] option in  
the expanded settings menu (G P.98),  
you can connect to a wireless LAN without  
adjusting settings in the ST-10 [Wireless  
LAN] tab (G P.117).  
Available Setting Description  
Off  
Simple connection off; the camera connects using the wireless  
LAN settings for the host selected for [Send To] (G P.102).  
WPS Button  
WPS PIN  
Scan  
If the wireless LAN access point is equipped with a WPS button,  
you can connect by simply pressing the button.  
If the wireless LAN access point uses a WPS PIN code, you can  
connect by entering the PIN on the camera.  
The camera automatically searches for and selects a wireless  
LAN access point and prompts you to enter a network key  
and other information as required. The camera stores this  
information even when turned off and supplies it automatically  
the next time you connect to the network.  
Connection Inf  
The camera displays information for the wireless LAN access  
point to which you are currently connected.  
12  
128  
Connecting Using [WPS Button]  
Select [WPS Button] for [Simple Connection].  
1
• Highlight [Simple Connection] in the expanded settings menu  
(G P.98) and press $, and then press ! or " to highlight [WPS  
Button] and press $. A message will be displayed while the camera  
waits for a signal from the wireless LAN access point.  
Press the WPS button.  
2
• Press the WPS button on the wireless LAN access point (see the  
documentation provided with the device for details). The camera  
will display connection information to show that the connection  
has been successfully established; press MENU/OK to return to the  
expanded settings menu. If the connection fails or if no connection  
is established within two minutes, an error will be displayed and the  
camera will exit to the expanded settings menu.  
Connecting Using [WPS PIN]  
Select [WPS PIN] for [Simple Connection].  
1
• Highlight [Simple Connection] in the expanded settings menu  
(G P.98) and press $, and then press ! or " to highlight [WPS  
PIN] and press $.  
Enter the PIN.  
• Enter an eight-digit PIN using the on-  
screen keyboard (G P.91) and press  
2
MENU/OK. A message will be displayed  
while the camera connects. Connection  
information is displayed if the attempt  
is successful; press MENU/OK to return  
to the expanded settings menu. If the  
connection fails, an error will be displayed and the camera will exit  
to the expanded settings menu.  
12  
Note-------------------------------------------------------------------------------------  
The camera stores the PIN even when turned off.  
129  
Connecting Using [Scan]  
Select [Scan] for [Simple Connection].  
1
• Highlight [Simple Connection] in the expanded settings menu  
(G P.98) and press $, and then press ! or " to highlight [Scan]  
and press $. A message will be displayed while the camera searches  
for wireless LAN access points; when the search is complete, a list of  
the available access points will be displayed.  
Select an access point.  
2
• Press ! or " to highlight an access point and press MENU/OK. The  
camera will attempt to connect using the wireless LAN settings  
last entered for [Scan]. If the attempt is successful, connection  
information will be displayed; press MENU/OK to return to the  
expanded settings menu.  
• If no previous settings exist or if the settings are incorrect, a message  
will be displayed prompting you to enter wireless LAN information  
manually; highlight [OK] and press MENU/OK to display wireless LAN  
settings (G P.117). Press ! or " to highlight items and press $ to  
select. Edit settings, using the on-screen keyboard where required,  
and press MENU/OK to connect when settings are complete.  
Connection information will be displayed if the camera is able to  
connect; press MENU/OK to return to the expanded settings menu.  
Caution---------------------------------------------------------------------------------  
Upload will be cancelled if the camera is unable to connect at current settings.  
The camera will not attempt to connect to the host selected for [Send To]  
(G P.102).  
12  
130  
Transferring Images During Playback  
(Wireless LANs)  
The [File Send] option in the playback menu (G P.72) can be used to  
upload images to a computer during playback.  
Caution---------------------------------------------------------------------------------  
Before uploading images over a wireless LAN, use a computer to create a host list  
and transfer it to the camera (G P.123). Images can not be uploaded if a host list  
has not been transferred to the camera or if the settings in the list are incorrect.  
Select [File Send].  
1
• If you intend to copy only one picture,  
display the picture full frame before  
proceeding. Highlight [File Send] in  
the playback menu (G P.72) and  
press $. If [On] is selected for [Send  
Status] (G P.102), the host list will be  
displayed. If [Off] is selected, proceed  
to Step 3.  
Choose a host.  
• Press ! or " to highlight a device and press MENU/OK.  
2
Transfer images.  
3
• Highlight [Send One] (send only the  
current image) or [Send All] (copy  
all images), and press MENU/OK. A  
progress indicator will be displayed.  
12  
Press MENU/OK when transfer is complete.  
• A message will be displayed when transfer is complete. Press MENU/  
OK to return to playback.  
4
131  
Transferring Multiple Selected Images -----------------------------------------  
To transfer multiple selected images, select thumbnail view (G P.38) before  
selecting [File Send]. After choosing a device as described in Step 2, highlight still  
images and press MENU/OK to select or deselect. Press DISP. when your selection  
is complete. A confirmation dialog will be displayed; highlight [Yes] and press  
MENU/OK to transfer the selected images.  
Skipping Steps 1 and 2--------------------------------------------------------------  
Once you have selected a host and password, the options in Step 3 can be  
displayed by pressing and holding DISP. during playback.  
Interrupting Transfer ---------------------------------------------------------------  
Pressing DISP., 6, or the shutter release button interrupts transfer.  
Note-------------------------------------------------------------------------------------  
Images are transferred at the size currently selected for [Image File Size]  
(G P.103) in the expanded settings menu (G P.98).  
Transferring Images During Shooting  
(Wireless LANs)  
The [Quick Send Mode] option in the expanded settings menu  
(G P.98) can be used to transfer photographs as they are taken.  
Available Setting Description  
Off  
Photos are not uploaded during shooting.  
1Touch  
Press MENU/OK when a photo is displayed after shooting to  
begin upload. Movies can not be transferred.  
2Touch  
Auto  
Press $ to display the most recent photograph or movie and  
press MENU/OK to begin upload. Not available when [On] is  
selected for [GPS Lock] (G P.99).  
Photos are automatically uploaded at their original size as they  
are taken. Photos are not converted to the size selected for  
[Image File Size] (G P.103) in the expanded settings menu  
(G P.98).  
12  
132  
Caution---------------------------------------------------------------------------------  
• Before uploading images over a wireless LAN, use a computer to create a host  
list and transfer it to the camera (G P.123). Images can not be uploaded if a  
host list has not been transferred to the camera or if the settings in the list are  
incorrect.  
• Photos are not uploaded in scene mode (G P.52) or if [On] is selected for  
[Continuous Mode] (G P.64) in the shooting menu.  
• During transfer, the flash does not charge and optical zoom is disabled.  
Note-------------------------------------------------------------------------------------  
• Before shooting, confirm that the host device is on.  
• The [Auto Delete] option (G P.104) in the expanded settings menu (G P.98)  
can be used to automatically delete photos from the camera after transfer.  
Interrupting Transfer/Terminating the Connection -------------------------  
To interrupt transfer, rotate the mode dial or press DISP., 6, or the shutter release  
button. To interrupt transfer and terminate the connection, select playback mode  
or turn the camera off.  
Choosing a Host----------------------------------------------------------------------  
Photos are automatically uploaded to the device last selected for [File Send] in  
playback mode (G P.74). Use [File Send] to choose a different device.  
One-Touch Transfer  
When [1Touch] is selected for [Quick Send Mode], the MENU/OK  
button can be used when a photo is displayed after shooting to  
upload it to the host currently selected for [File Send] (if no host is  
selected, the photo will be uploaded to the first host in the host list).  
The photo is not uploaded if the button is not pressed in the time  
selected for [LCD Confirmation Time] (G P.84) in the setup menu  
(G P.82); longer times are recommended.  
12  
A wireless LAN antenna icon is displayed  
while the camera is connected; when  
transfer is complete, the camera will return  
to shooting mode without terminating  
the connection. The connection can be  
terminated by selecting playback mode or  
turning the camera off.  
133  
Note-------------------------------------------------------------------------------------  
• Photos can not be uploaded if: [Off] is selected for [LCD Confirmation Time], or  
[On] or [WB-BKT] is selected for [Auto Bracket].  
• Images are not resized during transfer, regardless of the option selected for  
[Image File Size] (G P.103) in the expanded settings menu (G P.98).  
Two-Touch Transfer  
To upload your most recent photo:  
Press $.  
1
• A confirmation dialog will be displayed. (If this is the first time you  
have used two-touch transfer and [On] is selected for [Send Status]  
as described on P.102, you will be asked if you wish to choose a host;  
highlight [Yes] and press MENU/OK to display the host list. Press !  
or " to highlight a host and press MENU/OK. If the desired host  
does not appear, press ADJ./MEMO to refresh the list. If [Off] is  
selected for [Send Status], the image will be uploaded to the host  
selected for [Send To].)  
Press MENU/OK to begin transfer.  
• A progress indicator is displayed  
2
during transfer. A wireless LAN  
antenna icon is displayed while the  
camera is connected; when transfer  
is complete, the camera will return to  
shooting mode without terminating  
the connection. The connection can be  
terminated by selecting playback mode or turning the camera off.  
12  
Note-------------------------------------------------------------------------------------  
• Two-touch transfer can not be used when [On] is selected for [GPS Lock]  
(G P.99) in the expanded settings menu (G P. 9 8 ) .  
• Unless [BIP] is selected for [Bluetooth Profile] (G P.104) in the expanded  
settings menu (G P.98), images are transferred at the size currently selected  
for [Image File Size] (G P.103) in the expanded settings menu (G P.98).  
Choosing a Host----------------------------------------------------------------------  
Photos are automatically uploaded to the device last selected for [File Send] in  
playback mode (G P.74). Use [File Send] or the [Send To] option (G P.102) in  
the expanded settings menu (G P.98) to choose a different device.  
134  
Auto Transfer  
Select [Auto] to automatically upload photos as they are taken.  
Caution---------------------------------------------------------------------------------  
Images are not resized during transfer, regardless of the option selected for  
[Image File Size] (G P.103) in the expanded settings menu (G P.98).  
12  
135  
13 GPS  
When an optional GP-1 GPS unit or Bluetooth®-equipped GPS unit is  
connected, the camera can record the GPS data (including latitude,  
longitude, and compass heading) supplied by the device.  
Caution---------------------------------------------------------------------------------  
• GPS data are not recorded with photos taken in text mode.  
• Local geographic conditions may prevent or delay the acquisition of GPS data.  
• When both a GP-1 and a Bluetooth®-equipped GPS unit are connected, the  
preferred source can be selected using the [GPS Data Select] option (G P.100)  
in the expanded settings menu (G P.98).  
Connecting to a GPS Unit  
The GP-1 GPS Unit (Available Separately)  
There is no need for complicated  
adjustments to camera settings when  
using the GP-1. To connect the GP-1, turn  
the camera off and use the supplied Allen  
key to remove the side cover from the  
camera. Connect the GP-1 with the status  
indicator at the rear of the camera and  
tighten the locking nut.  
Note-------------------------------------------------------------------------------------  
• The GP-1 is not equipped with a battery or on/off switch. It turns on to supply  
GPS data when the camera is turned on and turns off when the camera is  
turned off.  
• Turn the camera off before connecting or disconnecting the GP-1.  
13  
136  
Bluetooth®-equipped GPS Units  
Bluetooth®-equipped GPS units supply GPS data to the camera  
wirelessly.  
Select [Bluetooth Serial].  
1
• Highlight [Bluetooth Serial] in the expanded settings menu  
(G P.98) and press $ (if this is the first time you have used  
Bluetooth®, the dialog shown at right will be displayed; press #  
or $ to highlight [Yes] and press MENU/OK to scan for available  
Bluetooth® devices).  
Highlight a device.  
2
• Press ! or " to highlight a device (to  
view a description of the device, press  
$; to remove the device from the list,  
press D). If the desired device does not  
appear, press ADJ./MEMO to refresh the  
list.  
Press MENU/OK.  
• Press MENU/OK. The camera will show  
3
connection status. If prompted for a  
password, press MENU/OK and enter a  
password as described on P.106. When  
a connection is established, GPS data,  
a Bluetooth® antenna icon, and a GPS  
icon will appear in the shooting display.  
13  
137  
Note-------------------------------------------------------------------------------------  
[Send To] lists the most recent device first.  
Terminating the Connection ------------------------------------------------------  
Turning the camera off terminates the connection.  
Connecting Automatically---------------------------------------------------------  
• Selecting [On] for [Bluetooth Auto Conn] (G P.103) in the expanded settings  
menu (G P.98) allows the camera to connect automatically to the most  
recently-used Bluetooth®- equipped GPS unit. If the camera is turned off with  
this option selected, when next turned on it will automatically scan for and  
attempt to connect to the most recently used Bluetooth®- equipped GPS unit.  
The camera will not connect if the unit is out of range or otherwise inaccessible  
(G P.105).  
• [Bluetooth Auto Conn] is for use only with GPS devices.  
• If prompted to supply a password, press MENU/OK and enter the password for  
the Bluetooth® device (G P.106).  
• To prevent the camera from connecting automatically, select [Off] for  
[Bluetooth Auto Conn] before turning the camera off.  
13  
138  
The GPS Data Display  
Bluetooth® icon  
(Bluetooth®-equipped GPS units only)  
During shooting, GPS data  
are displayed as shown  
at right.  
Heading (GP-1)  
Latitude/  
longitude  
×3(4)  
Satellites visible  
at current  
location  
Number of  
satellites used  
Accuracy  
To view more data, press DISP.  
Note-------------------------------------------------------------------------------------  
The format for the compass heading and for latitude and longitude can be  
chosen using the [Compass Heading] (G P.100) and [GPS Disp Mode] (G P.99)  
options in the expanded settings menu (G P.98).  
Accuracy -------------------------------------------------------------------------------  
The accuracy of the GPS data is displayed as shown below:  
Display  
no fix  
2d  
3d  
Diff  
Contents  
The GPS unit cannot receive data.  
The NMEA-0183 format GSA positioning mode is 2d.  
The NMEA-0183 format GSA positioning mode is 3d.  
The NMEA-0183 format GGA quality is DGPS.  
13  
139  
Caution---------------------------------------------------------------------------------  
Some time may be required to update GPS data.  
If the number of satellites drops below three,  
the GPS icon changes to show that GPS data  
can not be acquired.  
Retention of GPS Data--------------------------------------------------------------  
If the camera is unable to update GPS data, it will store and use the most recently  
acquired data for up to ten minutes. Note that these data are deleted if the [GPS  
Datum] option (G P.99) in the expanded settings menu (G P.98) is used to  
select a different geodetic system.  
Recording GPS Data  
GPS data can be recorded with each photograph and movie taken  
(note that GPS data are not recorded with photographs taken in text  
mode).  
With the GPS function enabled, turn the Mode Dial to  
5/V.  
1
Confirm that the camera is  
receiving GPS data.  
2
• Confirm that the GPS icon and GPS data  
are displayed. Detailed information can  
be viewed by pressing DISP.  
Shoot photos or movies.  
3
13  
• GPS data will be recorded with each photograph or movie taken  
according to the options currently selected for [GPS Data Imprint]  
(G P.101), [UTC Data Imprint] (G P.101), and [Heading Data  
Imprint] (G P.101) in the expanded settings menu (G P.98).  
Caution---------------------------------------------------------------------------------  
If no GPS data are available when the shutter release button is pressed halfway,  
the message“NO GPS FIX”will be displayed and no GPS data will be recorded  
when the picture is taken.  
140  
Viewing GPS Data  
/
GPS data recorded with pictures can be  
viewed during playback by pressing the  
DISP. button until GPS data are displayed.  
Note-------------------------------------------------------------------------------------  
• Latitude and longitude are displayed in orange if current GPS data were  
unavailable when the picture was taken (G P.136).  
• GPS data are included with images transferred to a computer (G P.105, 112).  
• GPS data are displayed in the format selected for [GPS Disp Mode] (G P.99) in  
the expanded settings menu (G P.98).  
The GPS Log ---------------------------------------------------------------------------  
The camera logs GPS data to the memory card at the interval selected for [GPS  
Track Time] (G P.100) in the expanded settings menu (G P.98; no log is  
created if [Off] is selected). Log files can be viewed in a text editor or word  
processing software. Entries consist of the longitude, latitude, altitude, track  
number, and the date and time, separated by commas; for example, an entry  
recording a position of 35° 40´ 1˝ N 139° 45´ 47˝ E at an altitude of 3.5 m at  
07:58:14 on October 8, 2010 (UTC) would take the following form:  
139.82972,35.66694,3.5,0,08-10-2010 07:58:14  
Longitude  
Altitude  
Date  
Time  
Latitude Track no.  
A track number of“1”indicates data logged at the start of GPS recording, “0”data  
logged during GPS recording.  
13  
141  
14 Barcode Reader  
The BR-1 Barcode Reader  
When connected to the camera, the BR-1 barcode reader (available  
separately) can be used to read linear barcodes for use in camera  
memos (G P.57). See the documentation provided with the BR-1 for  
more information.  
Caution---------------------------------------------------------------------------------  
• Do not transfer or sell the BR-1 to a third party.  
• The BR-1 is for commercial use only.  
• Be sure that you have read and understood the documentation and all safety  
warnings provided with the BR-1 and related equipment.  
To connect the BR-1, turn the camera off  
and use the supplied Allen key to remove  
the side cover from the camera. Connect  
the BR-1 with the read button at the rear of  
the camera and tighten the locking nut.  
When the camera is turned on, it will detect  
the BR-1 and an icon will be displayed.  
Barcodes can be read by pressing the  
BR-1 read button when the camera memo  
dialog is displayed (G “Software User  
Guide”P.36).  
14  
142  
Note-------------------------------------------------------------------------------------  
• The BR-1 is not equipped with a battery or on/off switch. It turns on when the  
camera is turned on and turns off when the camera is turned off.  
• Turn the camera off before connecting or disconnecting the BR-1.  
• The camera can not be used to read barcodes while the BR-1 is connected.  
Disconnect the BR-1 to read matrix barcodes.  
• The BR-1 can not be used to read password codes when [Barcode] is selected  
for [Choose/Change Password] (G P.90) in the setup menu (G P.82).  
14  
143  
15 Direct Printing  
About the Direct Print Function  
The Direct Print standard enables direct printing from a camera to a  
printer by connecting them via a USB cable. Photos can be printed  
quickly and easily from your digital camera without using a computer.  
Caution---------------------------------------------------------------------------------  
You cannot print AVI files (movies) with this function.  
Note-------------------------------------------------------------------------------------  
• This camera uses PictBridge, an industry standard for Direct Printing.  
• Your printer must be compatible with PictBridge to use the Direct Print  
function. For support information, see the documentation that came with the  
printer.  
Connecting the Camera to a Printer  
Connect your camera to a printer using the USB cable provided.  
Make sure that the camera power is off.  
1
2
Open the terminal cover.  
• Slide the knob in the direction  
shown and open the terminal  
cover.  
Connect your camera to a printer  
3
using the USB cable provided.  
• Turn on the printer if it is not already on.  
• Your camera turns on automatically.  
15  
Note-------------------------------------------------------------------------------------  
To disconnect the camera from the printer, check that the camera is turned off  
after printing is finished, and disconnect the USB cable.  
144  
Caution---------------------------------------------------------------------------------  
• Do not force the USB cable into the terminal.  
• Do not apply excessive force with the USB cable connected.  
• When using the USB cable, do not move the camera with the USB cable.  
• To prevent moisture or dust from entering the camera, close the terminal cover  
securely after disconnecting the USB cable.  
Printing Still Images  
You can print still images from the camera with a PictBridge-  
compatible printer. If a memory card is inserted, the pictures will be  
printed from the memory card; otherwise pictures will be printed from  
internal memory.  
Caution---------------------------------------------------------------------------------  
Do not disconnect the USB cable during printing.  
Note-------------------------------------------------------------------------------------  
• If a [Printer error.] message appears during image transfer, check the printer  
status and take the appropriate action.  
• If a computer connection message appears even though the camera is  
connected to the printer, reconnect the camera and press the ADJ./MEMO  
button within two seconds.  
Before printing, connect the camera to the  
printer. The message [Connecting...] shown  
at right will be displayed if the printer is  
ready; press the ADJ./MEMO button to view  
the Direct Print playback display.  
Printing One or All Still Images  
Select an image for printing and press the ADJ./MEMO  
button.  
1
15  
Select [1 File] or [All Files] and press the ADJ./MEMO button.  
• The Direct Print menu appears.  
2
145  
Select an item and press the $ button to view the options  
available.  
3
• When [Connecting…] is displayed,  
the connection to the printer is not  
yet established. When a connection is  
established, [Connecting…] disappears  
and [Direct Print] appears. Proceed  
with this step after the connection is  
established.  
• The following items can be selected. Each item is available only  
when supported by the printer connected to the camera.  
Item Name  
Description  
Printing Quantity Sets the print quantity.  
Paper Size  
Paper Type  
Layout  
Sets the paper size.  
Sets the paper type.  
Sets the number of images printed on a sheet of paper.  
The number of images that can be laid out on a sheet of  
paper varies depending on the connected printer.  
Report Print (*) Prints on forms.  
Memo Print (*)  
Choose whether reports will include camera memo  
descriptions (G P.148). Depending on the layout selected  
with [Report Print], the camera memo may not be printed.  
In this case, delete some of the information in the camera  
memo.  
Print Size  
Date Print  
Sets the print image size.  
Selects whether to print the date (shooting date). The  
date format can be set using the date/time option in the  
setup menu. If the picture was taken using [Date Imprint]  
(G P.65), only the imprinted date will be printed.  
File Name Print Selects whether to print the file name.  
Optimize Image Selects whether to optimize the image data (still image)  
prior to printing on the printer.  
Print Quality  
Sets the print quality.  
Toner Saving (*) Selects whether to conserve toner by using less ink during  
printing.  
1-Side/2-Sides (*) Selects whether to print on both sides of the paper.  
During duplex printing, one copy is printed for each still  
image. Only one copy is printed even if you selected more  
than one copy to print in Step 3 on P.147.  
15  
(
) Compatible Ricoh printers only.  
*
146  
Note-------------------------------------------------------------------------------------  
• To specify the settings as the default settings  
next time the camera is connected to the  
printer, press the ADJ./MEMO button when the  
screen in Step 3 is displayed. Select [Yes] in the  
display at right and press the MENU/OK button.  
• To use the settings last set the next time the  
camera is connected to the printer, select [No].  
Select an option and press the MENU/OK button.  
• The display returns to the Direct Print menu.  
• Repeat Steps 3 and 4 to change other settings as required.  
4
5
Press the MENU/OK button.  
• The selected still images are sent to the printer and the [Sending…]  
screen appears.  
• Pressing the DISP. button cancels the operation.  
• When the images have been sent to the printer, the display returns  
to the Direct Print playback mode screen and printing starts.  
Printing Several Still Images  
Press the 9 (Thumbnail view) button.  
• Photos will be displayed in multi-frame playback.  
1
Select an image and press the MENU/OK button.  
2
3
Press the !" buttons to set the  
number of copies to print.  
• Press the ! button to increase the  
number of copies, or press the "  
button to decrease the number of  
copies.  
• Repeat Steps 2 and 3 to select  
additional images.  
15  
Press the MENU/OK button.  
• The Direct Print menu appears.  
4
5
Select an item and press the $ button to view the options  
available.  
• See Steps 3 and following on P.146.  
147  
Note-------------------------------------------------------------------------------------  
• Only images with a printer symbol (p) are printed. If you cancel printing and  
then try to print again, make sure that the printer symbol is on the images you  
want to print.  
• The same still image can also be printed several times on a single sheet.  
• The available items vary depending on the functions of the printer.  
• To print images using the printer’s default settings, select [Printer Select] on the  
detailed options screen.  
Printing Reports  
Select [Report Print] on the Direct Print menu.  
You can only select [Report Print] when the camera is connected to a  
Ricoh printer that supports PictBridge after setting [Paper Size] to [A4]  
on the menu.  
The layout that can be selected depends on the connected printer. For  
more details, see the documentation that came with the printer.  
Available Layouts  
1 Frame W/Rule  
2 Frames W/Rule  
3 Frames W/Rule  
4 Frames W/Rule  
1 Frame W/O Rule 2 Frames W/O Rule 3 Frames W/O Rule 4 Frames W/O Rule  
Const. Photo 1  
W/Remark Section Additional Report  
1-10  
Examples of Printed Reports  
15  
1 Frame W/Rule  
2 Frames W/O Rule  
Const. Photo 1  
Note-------------------------------------------------------------------------------------  
Memos will only be included in the report if [5] is selected for [Number of Items]  
in the List Editor (G “Software User Guide”P.24).  
148  
16 Copying Pictures to a Computer via USB  
The screen images shown here may differ from the images displayed  
on your computer depending on your computer OS.  
For Windows  
You can copy pictures to your computer with or without DL-10  
software, which can be installed from the supplied CD.  
System Requirements for Using the Supplied CD-ROM  
The following environments are necessary for using the supplied CD-  
ROM. Please check your computer, or the computer's user manual.  
Operating Systems  
Supported  
Windows 2000 Professional Service Pack 4  
Windows XP Home Edition Service Pack 3/Professional Service Pack 3  
Windows Vista Service Pack 2  
Windows 7 (32- and 64-bit)  
CPU  
Pentium® IV: 1.6 GHz or faster  
Pentium® M: 1.4 GHz or faster  
Core™ 2 Duo: 1.5 GHz or faster  
Memory  
Windows 2000/Windows XP: 512 MB or more  
Windows Vista/Windows 7: 1 GB or more  
300 MB or more  
Hard drive space  
required for installation  
Display Resolution  
Display Colors  
1024 × 768 pixels or greater  
65,000 colors or greater  
CD-ROM Drive  
USB Port  
A CD-ROM drive compatible with the above-mentioned computer  
A USB port compatible with the above-mentioned computer  
16  
149  
Caution---------------------------------------------------------------------------------  
• The CD-ROM supports Japanese, English, French and German. Operations are  
not guaranteed on operating systems with other languages.  
• 64-bit Windows Vista is not supported.  
• If your computer has an upgraded OS, the USB function may not work normally,  
so it cannot be supported.  
• The provided software may not operate properly if changes are made to the  
operating system, such as with patches and service package releases.  
• The camera does not support connection to a USB port added by using an  
extension function (PCI bus or other).  
• If used in conjunction with a hub or other USB devices, the software may not  
work properly.  
• When dealing with movies and other large files, a larger memory environment  
is recommended.  
• MediaBrowser is not supported under Windows 2000.  
CD-ROM Setup  
Once you insert the supplied CD-ROM in the CD-ROM drive, the  
installer screen appears automatically.  
Windows 2000/Windows XP  
• The installer screen appears automatically.  
Windows Vista/Windows 7  
• If an Autorun dialog is displayed, select [Run Autorun.exe]. The installer  
will start automatically.  
Use this button to install  
software required for batch  
downloading and editing of  
images.  
Install EC1 image  
authentication software.  
16  
Click this to display the list of  
files contained on the CD-ROM.  
150  
Installing Software  
Click [Installing the software] to install the following software.  
Software  
DL-10  
List Editor  
ME1  
Description  
Downloads images collectively to your computer.  
Create memo lists.  
View and manage photographs to which memos have  
been appended, edit memos, and print memos with  
photographs.  
ST-10  
SR-10  
Adjust settings for connection to wireless LANs.  
Create an ftp server on your computer for the exclusive  
use of this camera.  
MediaBrowser  
USB Driver  
Display, manage, and edit existing images. Not supported  
under Windows 2000.  
Used to connect an earlier model Ricoh camera to  
a computer running Windows 98/Windows 98 SE/  
Windows Me/Windows 2000. Not used with this camera.  
Used to connect an earlier model Ricoh camera to  
a computer running Windows XP/Windows Vista/  
Windows 7. Not used with this camera.  
WIA Driver  
Caution---------------------------------------------------------------------------------  
• Do not install the software when the camera is connected to your computer  
with a USB cable.  
• The names for DC Software items differ from the names for Caplio Software  
items provided with previous models as shown below.  
Caplio Software  
RICOH Gate La  
Caplio Viewer  
DC Software  
DL-10  
DU-10  
Caplio Server  
SR-10  
Caplio Setting  
ST-10  
If Caplio Software from a CD-ROM supplied with a previous model is already  
installed on your computer, a message asking you to uninstall the Caplio  
Software before installing DC Software will appear when you try to install the  
new software.  
• Administrator privileges are required for installation.  
16  
• DL-10 is not network-compatible. Use as a stand-alone application.  
151  
Click [Installing the software].  
Windows 2000/Windows XP  
1
• After a while, the [Choose Setup Language] screen appears.  
Windows Vista/Windows 7  
• If a [User Account Control] dialog is displayed, select [Yes]  
(Windows 7) or [Allow] (Windows Vista). After a short pause, the  
[Choose Setup Language] dialog will be displayed.  
Select a language and follow the on-screen instructions to  
complete installation.  
• The MediaBrowser installer will start. To install MediaBrowser, accept  
the license agreement and follow the on-screen instructions.  
2
3
When a message appears asking you to restart your  
computer, select [Yes, I want to restart my computer now.]  
and then click [Finish].  
• Your computer will restart automatically.  
• After your computer restarts, a Windows security warning message  
appears.  
Click [Unblock] for DL-10.  
4
Installing EC1  
EC1 can be used to determine whether photographs shot with [On]  
selected for [Edit Detection] (G P.66) in the shooting menu have  
been altered since they were taken. See the “Software Users Guide”for  
details.  
Click [Installing EC1].  
1
• Depending on your user environment, an installation message for  
“Visual C++ Runtime Library (×86)”or “.NET Framework 2.0”may  
be displayed. If this message appears, follow the instructions on  
the message to install the software. If a message instructing you to  
restart your computer appears after installation, please restart your  
computer.  
Follow the on-screen instructions and install EC1.  
2
16  
152  
Caution---------------------------------------------------------------------------------  
If EC1 is already installed on your computer, you cannot reinstall it. If you try to  
reinstall it, a message asking if you want to change or delete EC1 is displayed. To  
exit without changing or deleting EC1, click [Cancel].  
Installing Other Software  
Click [Browse CD-ROM Content] to install the following software:  
Software  
Adobe Reader  
EX1  
Description  
Required to view manuals in pdf format.  
Rename files according to memo descriptions or export  
memos as CSV, XML, or text. EX1 comes in server and  
client versions.  
Caution---------------------------------------------------------------------------------  
• Do not install the software when the camera is connected to your computer  
with a USB cable.  
• Administrator privileges are required for installation.  
• To install MediaBrowser without installing other applications, double-click the  
setup.exe icon in the“MediaBrowser”folder.  
Installing Adobe Reader  
Acrobat Reader or Adobe Reader need not be installed if already  
installed on your computer.  
Note-------------------------------------------------------------------------------------  
• For details about Adobe Reader, see Help for Adobe Reader.  
• Installation of Adobe Reader 9.3 requires either Microsoft Internet Explorer  
6.0 or later or Firefox 2.0 or later. Microsoft Internet Explorer is available via  
Microsoft Update.  
• Installation of Adobe Reader 9.3 requires MSI (Microsoft Windows Installer)  
version 3.1 or later. Microsoft Windows Installer is available via Microsoft Update.  
16  
153  
Click [Browse CD-ROM Content].  
• The files on the CD-ROM are listed.  
1
2
Open the folder for your language in the [Adobe Reader]  
folder and double-click the Adobe Reader installer.  
• A screen appears to confirm user account management for  
Windows 7 and Windows Vista. Select [Continue].  
Install Adobe Reader by following the messages displayed.  
3
Installing EX1  
For information on using EX1, see the “Software Users Guide”.  
Click [Browse CD-ROM Content].  
• The files on the CD will be displayed.  
1
Start the installer.  
2
• Double-click [EX1] and then double click either [EX1_for_Server]  
(or [EX1_for_Server.exe]) or [EX1_for_Client] (or [EX1_for_Client.  
exe]). Under Windows 7 and Windows Vista, a [User Account Control]  
dialog will be displayed; click [Continue].  
Install EX1.  
• Follow the on-screen instructions.  
3
Uninstalling the Software ---------------------------------------------------------  
•
The software can be uninstalled using the [Programs and Features] control panel  
(Windows 7 and Windows Vista) or [Add/Remove Programs] control panel (other  
versions of Windows).  
• Administrator privileges are required.  
• Quit any other programs that may be running before uninstalling the software.  
16  
154  
Copying Pictures to Your Computer  
Follow the steps below to copy pictures to your computer.  
Connect the camera to the computer  
using the supplied USB cable.  
1
• Turn the camera off before connecting  
the USB cable.  
• The camera turns on automatically when  
a connection is established.  
Copy photos to the computer.  
If DL-10 is installed:  
2
• DL-10 starts and image transfer begins automatically.  
• Pictures are copied to the [Digital Camera] folder in [My Documents],  
where they are sorted into separate folders by date of recording. See  
the “Software User Guide”on the supplied CD for more information.  
If DL-10 is not installed:  
• Copy files from the camera to the  
desired location.  
• When an SD memory card is  
loaded, its files are displayed.  
Otherwise, files in the internal  
memory are displayed.  
Example of the display  
in Windows XP  
16  
155  
Disconnect the USB cable when transfer is complete.  
• Click the [Safely Remove Hardware] or  
3
[Unplug or Eject Hardware] icon in the  
taskbar (the illustration above shows the icon for Windows XP) and  
select [Safely Remove USB Mass Storage Device] or [Stop USB Mass  
Storage Device] from the menu that appears. You can then  
disconnect the USB cable.  
• If the remove hardware icon is not displayed  
in Windows 7, click the button in the  
taskbar.  
Caution---------------------------------------------------------------------------------  
• Do not turn off the camera or disconnect the USB cable during image transfer.  
• Do not use force when connecting the cable or when handling the camera with  
the cable connected. Do not attempt to transport the camera while the USB  
cable is connected.  
• To prevent moisture or dust from entering the camera, close the terminal cover  
securely after disconnecting the USB cable.  
Note-------------------------------------------------------------------------------------  
The camera is provided with MediaBrowser software that allows you to display  
and edit images from your computer. For how to use MediaBrowser, see the  
displayed“Help”.  
For the latest information about MediaBrowser, access the Web page of Pixela Co.,  
Ltd. (http://www.pixela.co.jp/oem/mediabrowser/e/).  
16  
156  
For Macintosh  
This camera supports the following Macintosh operating systems.  
• Mac OS 9.0 to 9.2.2  
• Mac OS X 10.1.2 to 10.6.3  
Caution---------------------------------------------------------------------------------  
Although the software included in the CD-ROM cannot be used with Macintosh,  
it is possible to display the“Software User Guide”(note that Acrobat Reader is  
required to view the“Software User Guide”under Mac OS 9).  
Copying Pictures to Your Computer  
Follow the steps below to copy pictures to your computer.  
Connect the camera to the computer  
using the supplied USB cable.  
1
• Turn the camera off before connecting  
the USB cable.  
• The camera turns on automatically when  
a connection is established.  
Copy photos to the computer.  
• Copy files from the camera to the  
desired location.  
2
• When an SD memory card is  
loaded, its files are displayed.  
Otherwise, files in the internal  
memory are displayed.  
Disconnect the USB cable when transfer is complete.  
• Drag the camera volume into the Trash and then disconnect the USB  
cable.  
3
16  
157  
Caution---------------------------------------------------------------------------------  
• Do not turn off the camera or disconnect the USB cable during image transfer.  
• Do not use force when connecting the cable or when handling the camera with  
the cable connected. Do not attempt to transport the camera while the USB  
cable is connected.  
• You can also click [Eject] on the [Special] menu in Mac OS 9 or the [File] menu  
in Mac OS X to cancel the connection.  
• If the USB cable is disconnected without disabling the connection, the Unsafe  
Removal of Device screen may be displayed. Be sure to stop the connection  
before removing the USB cable.  
• When you connect your camera to a Macintosh computer, a file called  
“FINDER.DAT”or“.DS_Store”may be created in your SD memory card, which will  
appear as [Unmatched File] on your camera. You can delete this file from the SD  
memory card if you wish.  
• To prevent moisture or dust from entering the camera, close the terminal cover  
securely after disconnecting the USB cable.  
16  
158  
17 Appendices  
Troubleshooting  
Error Messages  
If an error message is displayed on the screen, check the information  
on the reference page and take the corresponding action.  
Non-Bluetooth® or Wireless LAN related error messages  
Error Message  
Insert card.  
Set date.  
Cause and Solution  
No card is loaded. Insert a card.  
The date is not set. Set the date.  
Refer to  
P.27  
P.86  
The file number limit has been  
exceeded.  
The file number limit has been exceeded. Use another card. P.86  
Unmatched File  
This file cannot be displayed on the camera. Check the file  
contents on your computer, and then delete the file.  
—
Insufficient memory. Continue?  
All the files cannot be copied because there is insufficient P.24  
memory on the card. Use another card.  
Protected  
The file selected for deletion is protected.  
The card is locked (write-protected). Unlock the card.  
Selected option is not available with SD WORM cards. Use P.24  
a different type of card.  
P.79  
P.25  
Card Is Write-Protected.  
This option is not available with  
SD WORM cards.  
Print settings cannot be applied  
to this file.  
This file (movie or other file) cannot be selected for  
printing.  
—
Insufficient Memory/  
Capacity Short  
Files cannot be stored. Make sure there is sufficient  
memory or delete unwanted files.  
P.41,  
P.83  
The image print number limit has been exceeded. Select an P.147  
image and set the number to 0.  
Format internal memory.  
Format card.  
The internal memory requires formatting.  
The card is not formatted. Format the card with this  
camera.  
P.83  
P.83  
Card Error  
Reformat the card. If the error message still appears after P.83  
that, the card may be faulty. Do not use the card.  
Writing Data  
No File  
Writing file to memory. Wait until writing finishes.  
There are no files that can be played back.  
—
—
Out of memory. cannot record.  
The number of remaining shots is 0. Switch to another card P.24  
or the internal memory.  
No files to restore.  
There are no files to restore.  
P.74  
17  
159  
Error Message  
Cause and Solution  
Refer to  
Can not —. *  
Selected option can not be applied to image more than  
once, or image was created with different make of camera.  
If image was created with different make of camera,  
process image using original make of camera.  
—
*
“—“ indicates the name of the process that can not be applied.  
Bluetooth® related error messages  
Error Message  
Cause and Solution  
Refer to  
Requested file cannot be sent.  
You attempted to send an image other than still ones  
(.JPG). Only still images (.JPG) can be sent.  
The input passkey did not match the destination device.  
Enter the correct passkey.  
The passkey was not entered within the time limit. Enter  
the passkey again within the time limit.  
At the start of transfer, the destination device could not be P.105  
connected due to one of the following causes. Check the  
device status and start again from the beginning.  
• Signal no longer reach the destination device.  
• The destination device does not exist nearby (about 10 m  
(3.3 ft.)).  
P.105  
Verifying failed.  
Cannot connect.  
—
P.106  
• The destination device is not active because the power is  
off or due to other causes.  
• The destination device does not support the Bluetooth®  
Profiles required for communication with this camera.  
• Inappropriate device was selected for the destination.  
Cannot send.  
Transfer was interrupted by one of the following causes.  
Check the device status and start again from the beginning.  
• Signal no longer reach the destination device.  
—
• The destination device can no longer receive a signal.  
• There is insufficient space on the destination device.  
Wireless LAN related error messages  
Communication and send setting errors  
Error Message  
Connection error  
Cause and Solution  
Refer to  
P.116,  
P.127  
The camera is unable to establish a connection for some  
reason. Check the communication settings.  
The [Send Method] setting is not selected in the  
communication settings. Select [Send via FTP].  
The destination access point is off or otherwise not  
operating. Check the access point.  
Send method must be selected  
Cannot connect to access point  
P.123  
—
Incorrect communication settings. Check the send settings. P.116  
17  
160  
Error Message  
Cause and Solution  
Refer to  
The IP address is already in use  
The same IP address as the camera exists in the destination P.116  
network. Check the [IP address] in the Detailed Setups  
[Networks] tab.  
Conflicting LAN setting  
The first destination sent to after turning the camera on  
and the setting in the Detailed Settings [Network] tab or  
[Wireless LAN] tab is different. To send to a destination  
different from the setting in the [Network] or [Wireless  
LAN] tab, change the destination in advance and restart  
the camera.  
P.116,  
P.117  
Destination not registered  
Invalid key size.  
The communication list has not been imported by the  
camera. Import the communication list into the camera  
and try again.  
When [Crypt/Authentication] in [W/less LAN] is changed  
on the camera, check the network key.  
P.123  
P.117,  
P.118  
• If [WEP/OPEN] or [WEP/SHARED] is selected for [Crypt/  
Authentication], enter the [Network Key] as below.  
[String]: Five characters or 13 characters  
[Hex]: Ten characters or 26 characters  
• If [AES/WPA-PSK], [AES/WPA2-PSK], [TKIP/WPA-PSK], or  
[TKIP/WPA2-PSK] is selected for [Crypt/Authentication],  
the network key must contain 64 characters ([Hex]) or  
from 8 to 63 characters ([String]).  
Cannot find access point.  
Camera could not find wireless LAN access point to which it P.128  
could connect using [Simple Connection] > [WPS Button]/  
[WPS PIN]; check device and confirm that signal is not  
blocked and that the access point is within distance of  
about 30 m (100 ft.).  
Connection information not  
available.  
Information required for connection to wireless LAN access P.128  
point is not available. Select any option other than [Off] for  
[Simple Connection] and try again.  
FTP send setting errors  
Error Message  
Cause and Solution  
Refer to  
No upload server name setting  
[Server Name] for the destination is not set in the Detailed P.118  
Setups [FTP Send] tab. Set the [Server Name] setting.  
Unable to acquire the IP address of the destination server. P.118  
Set the correct [Server Name] setting in the Detailed  
Setups [FTP Send] tab.  
Cannot detect IP address  
No response from server  
Cannot connect to server  
The destination server does not respond. Check the  
advanced settings on the [FTP Send] tab.  
Unable to connect to the destination server. Check the  
advanced settings on the [FTP Send] tab  
P.118  
P.118  
Setting error either in user name Incorrect [User Name] or [Password] setting. Set the correct P.118  
17  
or password  
[User Name] and [Password] settings in the Detailed  
Setups [FTP Send] tab.  
161  
Error Message  
Cause and Solution  
Refer to  
The folder does not exist.  
The specified inbox folder does not exist on the destination. P.118  
Set the correct [Folder Name] setting in the Detailed  
Setups [FTP Send] tab.  
Cannot send  
Server error  
Unable to send files for some reason. Check the advanced P.118  
settings on the [FTP Send] tab.  
An error is received from the server after connecting to the  
server. Try resending the file.  
—
Note-------------------------------------------------------------------------------------  
If you cannot solve the problem using the solutions above, contact a Ricoh office  
or your local authorized Ricoh dealer.  
17  
162  
Camera Troubleshooting  
Power Supply  
Problem  
The camera does not  
turn on.  
Cause  
Solution  
Refer to  
P.26,  
P. 2 7  
The battery is exhausted or not  
inserted.  
Check that battery is correctly  
inserted. Charge battery  
(rechargeable battery only),  
insert fresh battery.  
An unacceptable battery is used. Use supplied battery or  
compatible AAA batteries.  
P. 2 3  
P.29  
P.27  
—
The camera is automatically  
turned off by auto power off.  
The battery is loaded in wrong  
direction.  
Turn the camera back on.  
Load correctly.  
Because the camera overheated, Wait until the temperature of  
the power was automatically  
turned off.  
the camera returns to normal. Do  
not attempt to cool the camera  
suddenly.  
The camera turns off  
during use.  
The camera was left unattended  
and unused, so auto power off  
turned it off.  
Turn the camera back on.  
P.29  
Battery is exhausted.  
Check that battery is correctly  
inserted. Charge battery  
(rechargeable battery only),  
insert fresh battery.  
P.26,  
P. 2 7  
An unacceptable battery is used. Use supplied battery or  
compatible AAA batteries.  
P. 2 3  
P. 2 7  
P. 2 3  
The camera does not  
turn off.  
Camera malfunction  
Remove the battery and load  
it again.  
The battery has been  
fully charged, but:  
• The battery symbol is  
displayed, indicating  
a low battery level.  
• The camera turns off.  
Cannot charge the  
battery.  
A unacceptable battery is used.  
Use supplied battery or  
compatible AAA batteries.  
Battery has reached the end of its Replace with a new rechargeable P. 2 7  
useful life.  
battery.  
—
Battery runs out  
quickly.  
It is being used at extreme high or  
low temperatures.  
—
—
Many shots are being taken in  
dark places or other location  
requiring extensive use of flash.  
—
17  
163  
Shooting  
Problem  
Cause  
Battery is exhausted.  
Solution  
Refer to  
P.26,  
P. 2 7  
The camera does not  
shoot even if you press  
the shutter release  
button.  
Check that battery is correctly  
inserted. Charge battery  
(rechargeable battery only),  
insert fresh battery.  
The camera is not on.  
Press the POWER button to turn P. 2 9  
the camera on.  
The camera is in playback mode.  
P. 2 9  
Press the 6 (Playback) button  
to select the shooting mode.  
The shutter release button is not Press the shutter release button P. 3 2  
pressed all the way. all the way.  
The SD memory card is not formatted. Format the card.  
The SD memory card is full. Load a new card, or delete  
unwanted files.  
P.83  
P.27,  
P. 4 1  
P.27  
The SD memory card has reached Load a new SD memory card.  
the end of its useful life.  
The flash is charging.  
Wait until the auto focus/flash  
lamp stops blinking.  
P. 3 5  
The SD memory card is locked.  
The contact surface of the SD  
memory card is dirty.  
Unlock the card.  
Wipe with a soft, dry cloth.  
P.25  
—
Unable to view the shot The image confirmation time is  
image. too short.  
Lengthen the image  
confirmation time.  
P. 8 4  
Images do not appear The camera is not on, or the  
on the picture display. picture display is dark.  
Turn the camera on, or adjust the P.29,  
brightness of the picture display.  
P. 8 3  
The VIDEO/AV cable is connected. Disconnect the VIDEO/AV cable.  
—
The screen display is in synchro-  
monitor mode.  
Press the DISP. button to change P. 4 4  
the display.  
Although the camera  
is set to auto focus, it is  
unable to focus.  
The lens is dirty.  
The subject is not in the center of Shoot with focus lock.  
the shooting range.  
Wipe clean with a soft, dry cloth.  
—
P.31  
It is a hard-to-focus subject.  
Shoot with focus lock or manual P.31,  
focus.  
P. 6 7  
Although the camera is The camera incorrectly focused  
not in focus, the green because the distance to the  
frame appears in the  
center of the picture  
display.  
Shoot with macro mode, or move P. 3 4  
away from the subject.  
subject is too close.  
17  
164  
Problem  
Cause  
Solution  
Refer to  
The picture is blurred  
(The J symbol  
appears).  
You moved the camera when  
pressing the shutter release  
button.  
Hold camera in both hands with P. 3 1  
your elbows pressed lightly  
against your torso.  
Use a tripod.  
Use the camera shake correction  
function.  
P. 6 5  
When shooting in a dark place  
(such as indoors), the shutter  
speed slows down and pictures  
become easily blurred.  
Use the flash.  
P. 3 5  
P. 7 1  
P. 6 5  
Raise the ISO setting.  
Use the camera shake correction  
function.  
The flash does not fire. The flash cannot be used in the  
To shoot with the flash, change P.35,  
Or, the flash cannot  
charge.  
following cases:  
the settings or mode.  
P. 1 6 9  
• In bracket shooting  
• In continuous mode  
• In movie mode  
In some scene modes, the flash is  
disabled by default.  
The flash is set to flash off.  
Battery is exhausted.  
Cancel Flash Off.  
P.35  
P.26,  
P. 2 7  
Check that battery is correctly  
inserted. Charge battery  
(rechargeable battery only),  
insert fresh battery.  
Even though the flash The distance to the subject  
fired, the picture  
is dark.  
Get closer to your subject and  
shoot. Change the flash mode or  
the ISO setting.  
P.71,  
P. 1 7 1  
exceeds the flash range.  
The subject is dark.  
Correct the exposure (Exposure  
compensation also changes the  
light intensity of the flash).  
P. 6 9  
—
Cannot use the ADJ.  
button function.  
The camera memo list is saved on Delete files with the “.mta”  
the SD memory card.  
extension in the camera  
[TEMPLATE] folder.  
The image is too bright. The light intensity of the flash is  
not appropriate.  
Position yourself slightly further P. 3 5  
from your subject or turn the  
flash off and use other lighting.  
Subject is overexposed (The  
Correct the exposure.  
Cancel exposure time.  
Adjust the brightness of the  
picture display.  
P. 6 9  
P. 6 4  
P. 8 3  
[
Q] symbol appears).  
The brightness of the picture  
display is not appropriate.  
The image is too dark. The shot was taken in a dark place Cancel Flash Off.  
while set to flash off.  
P.35  
The subject is underexposed (The Correct the exposure.  
P. 6 9  
P. 6 4  
P. 8 3  
[
Q] symbol appears).  
Set the long exposure time.  
The brightness of the picture  
display is not appropriate.  
Adjust the brightness of the  
picture display.  
17  
165  
Problem  
Cause  
Solution  
Refer to  
The image lacks natural The picture was shot in conditions Add a white object to the  
P. 7 0  
color.  
that made it difficult for auto  
composition, or use a white  
white balance to adjust the white balance setting other than auto.  
balance.  
The date or recording  
information does not  
appear on the screen.  
The brightness of the  
picture display changes from that used for autofocus..  
during AF.  
Vertical streaks  
(“smear”) appear in  
photos.  
The screen display function is set Press the DISP. button to change P. 4 4  
to no display. the display.  
Ambient lighting is poor or differs This is normal.  
—
—
Subject is bright.  
This is normal and does not  
indicate a malfunction.  
The level indicator is  
not displayed.  
[Level Setting] is set to [Off] or  
[Sound].  
Set [Level Setting] to [Display] or P. 4 6  
[Disp + Snd].  
The display is set to a setting other Press the DISP. button to change P. 4 4  
than normal symbol display or  
histogram.  
the display to normal symbol  
display or histogram.  
The camera is upside down (The  
shutter release button is on the  
bottom).  
Hold the camera correctly.  
—
The image is tilted even You shot the image while moving, Shoot in an environment that is  
—
—
though it was shot with such as on a amusement ride.  
not moving.  
the level indicator in  
the middle or while  
the level sound was  
sounding.  
The subject is not level.  
Check the subject.  
17  
166  
Playback/Deleting  
Problem  
Cause  
Solution  
Refer to  
Cannot play back, or the The camera is not in playback  
P. 3 8  
Press the 6 (Playback) button.  
playback screen does  
not appear.  
mode.  
The VIDEO/AV cable is not  
connected properly.  
The [Video Out Mode] setting is  
incorrect.  
Connect properly.  
P.81  
P.86  
—
Set it to the correct format.  
The contents of the SD No SD memory card is loaded, or Load a card with stored images.  
memory card cannot an SD memory card with no stored  
be played back, or the images is loaded.  
playback screen does  
not appear.  
You played back an SD memory  
card that was not formatted with and recorded with this device.  
this device.  
Load a card that was formatted P.27,  
P. 8 3  
You played back an SD memory  
card that was not recorded  
normally.  
Load a normally recorded card.  
—
The contact surface of the SD  
memory card is dirty.  
There is something wrong with  
the SD memory card.  
Wipe with a soft, dry cloth.  
—
—
Play back images from another  
card and if there is nothing  
wrong with the card, the camera  
is okay. There may be something  
wrong with the card, so do  
not use it.  
The picture display  
turned off.  
Battery is exhausted.  
Check that battery is correctly  
inserted. Charge battery  
(rechargeable battery only),  
insert fresh battery.  
P.26,  
P. 2 7  
The camera was left unattended  
and unused, so auto power off  
turned it off.  
Turn the camera back on.  
P.29  
A file cannot be  
deleted.  
Cannot format the SD  
memory card.  
The file is protected.  
The SD memory card is locked.  
The SD memory card is locked.  
Unprotect the file.  
Unlock the card.  
Unlock the card.  
P.79  
P.25  
P.25  
17  
167  
Other Problems  
Problem  
Cause  
Solution  
Refer to  
Cannot load the SD  
memory card.  
The card is facing the wrong way. Load correctly.  
P.27  
The camera does not  
operate even when the  
buttons are pressed.  
Battery is exhausted.  
Camera malfunction  
Check that battery is correctly  
P.26,  
P. 2 7  
inserted. Charge battery  
(rechargeable battery only),  
insert fresh battery.  
Press the POWER button to turn P. 2 9  
the camera off, and then press  
the POWER button to turn the  
camera on again.  
Remove the battery and load  
it again.  
P. 2 9  
The date is incorrect.  
The set date  
disappeared.  
The correct date/time are not set. Set the correct date/time.  
P.86  
P. 8 6  
The battery was removed.  
If the battery is removed for  
more than three days, the date  
setting will be lost. Make the  
settings again.  
Auto power off does  
not work.  
Auto power off is set to [Off].  
Set the time for auto power off. P.84  
The operation sound  
cannot be heard.  
The operation sound volume is  
turned off.  
Use [Volume Settings] to set  
the volume to a setting other  
than mute.  
P. 8 4  
P.86  
Images do not appear The [Video Out Mode] setting is  
on the TV.  
Set it to the correct format.  
incorrect.  
The AV cable is not connected.  
The TV is not correctly set to  
VIDEO IN.  
Connect the AV cable properly.  
Check that the TV is correctly set  
to VIDEO IN.  
P.81  
—
17  
168  
Available Settings  
The following table lists the settings available in each shooting mode.  
W
5
V
N (Macro) *1  
F (Flash)  
✓
✓
✓
✓
—
—
—
✓
✓
✓
—
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
—
—
✓
—
✓
t (Self-timer) *2  
Digital Zoom *3  
Density  
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
—
—
—
— *4  
✓
—
—
—
✓
—
—
—
✓
—
—
—
—
—
—
✓
—
—
✓
Size  
Movie Size  
Picture Quality/Size  
Focus  
✓
—
—
—
—
—
—
—
—
—
—
—
—
—
—
✓
5
✓
*
—
✓
Multi AF *6  
Spot AF  
AF  
MF  
Snap  
∞
✓
✓
✓
—
—
✓
✓
✓
✓
✓
—
✓
✓
—
✓
—
—
✓
—
—
✓
—
✓
✓
✓
✓
✓
—
—
✓
✓
✓
✓
✓
✓
Exposure Metering  
Continuous Mode *7  
✓
✓
—
—
—
—
—
—
✓
—
—
—
—
—
—
✓
—
—
—
—
—
—
—
—
8
*
✓
✓
—
✓
Image Settings  
✓
✓
Auto Bracket *8  
*
✓
✓
9
—
—
—
✓
Time Exposure *10  
✓
✓
Interval Shooting *11  
✓
—
✓
Camera Shake Correction *12  
Date Imprint  
✓
✓
✓
✓
✓
✓
✓
*1 [Focus] is set to [Spot AF]. Disabled when [MF] is selected for [Focus].  
*2 Disabled during interval timer and continuous shooting.  
*3 Not available if image is zoomed in during manual focus.  
*4 Picture quality and size for CALS mode is selected using the [CALS Pic Quality] option in the  
setup menu.  
*5 [a4 : 3 F], [a4 : 3 N], and [z4 : 3 F] only.  
*6 Functions as [Spot AF] when digital zoom is in effect.  
*7 Disabled during interval timer shooting.  
*8 Flash turns off.  
*9 Disabled during continuous shooting.  
*10 Disabled during auto bracketing and continuous shooting.  
*11 Disabled when self-timer is used.  
*12 Not available if [Flash On], [FLASH ON (10M)], or [Flash Synchro.] is selected as flash mode for  
long time-exposures or continuous shooting or if ten-second self-timer is used.  
17  
169  
W
5
V
Exposure Compensation  
White Balance *13  
ISO Setting  
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
—
✓
✓
✓
✓
✓
✓
—
✓
✓
✓
✓
—
✓
✓
✓
✓
✓
—
✓
✓
✓
✓
✓
✓
✓
✓
✓
—
—
—
✓
—
✓
✓
✓
✓
—
✓
—
✓
—
—
—
—
—
✓
Edit Detection *14  
Restore Defaults  
ADJ Button Off  
✓
✓
—
—
✓
—
—
✓
—
—
✓
—
—
—
—
—
—
—
—
—
—
—
✓
—
—
✓
Setting 1–4  
Exposure Comp.  
White Balance  
ISO  
15  
*
✓
✓
✓
✓
—
—
—
—
—
—
—
—
✓
—
—
—
—
—
—
—
—
✓
—
—
—
—
—
—
—
—
✓
—
—
—
—
—
—
—
—
✓
—
—
—
—
—
—
—
—
—
✓
Quality  
Focus  
Image  
Expo. Metering  
Cont. Mode  
Auto Bracket  
Density  
Shooting Info. Display Frame  
Other than those above  
✓
✓
✓
✓
✓
✓
*13 Not available if [Black & White] is selected for [Image Settings].  
*14 Disabled during auto bracketing and continuous shooting.  
*15 The function displayed when the ADJ. button is pressed in scene mode is always the same and  
is not affected by the roles assigned to the button.  
17  
170  
Specifications  
No. of effective pixels (camera) Approx. 12.10 million effective pixels  
Image Sensor  
Lens  
1/2.3˝ CCD (Approx. 12.40 total million pixels)  
5.0 mm to 25 mm (equivalent to 28 mm to 140 mm on a 35-mm camera)  
F3.5 to F5.5  
Focal Length  
F-aperture  
Shooting Distance Normal shooting: Approx. 30 cm to ∞ (Wide-angle) or 50 cm to ∞  
(Telephoto) (from the front of the lens)  
Macro shooting: Approx. 1 cm to ∞ (Wide-angle), 15 cm to ∞ (Telephoto)  
or 1 cm to ∞ (Zoom macro mode) (from the front of the lens)  
Lens Construction 11 elements in 9 groups plus 1 prism  
Zoom Magnification  
Optical zoom at 5.0 ×, Digital zoom at 4.0 ×, Auto resize zoom at approx.  
6.3 × (VGA image)  
Focus Modes  
Multi AF (CCD method)/Spot AF (CCD method)/MF/Snap/∞ (with AF  
Auxiliary Light)  
Blur Reduction  
Digital image stabilizer  
Shutter  
Speed  
Still Image  
8, 4, 2, 1 to 1/1500 seconds (The upper and lower limits differ for each  
shooting mode and flash mode.)  
Movie  
Exposure Exposure  
Control  
1/30 to 1/10000 seconds  
Multi Light Metering (256 segments)/Center-weighted Light Metering/  
Metering Mode Spot Metering (TTL-CCD Metering)  
Exposure Mode Program AE  
Exposure  
Compensation  
Manual exposure compensation (+2.0 to –2.0 EV in 1/3 EV Steps), Auto  
bracket function (–0.5 EV, 0, +0.5 EV)  
Exposure Range Wide angle: 1.7–15.4 EV  
(auto mode, Telephoto: 3.0–15.6 EV  
center-weighted (Exposure range for auto ISO calculated using values for ISO 100.)  
metering)  
Note: At 6.0 EV or lower, each drop of 1.0 EV is associated with a 0.25 EV  
drop in brightness. Brightness drops by no more than 1.0 EV.  
Auto/ISO 64/ISO 100/ISO 200/ISO 400/ISO 800/ISO 1600/ISO 3200  
ISO Sensitivity (Standard  
Output Sensitivity)  
White Balance Mode  
Auto/Outdoors/Cloudy/Incandescent 1/Incandescent 2/Fluorescent/Manual/  
Ring Light, White balance bracket function  
Flash  
Flash Mode  
Auto flash (fires automatically in low-light conditions and when the subject  
is backlit)/Anti Red-eye/Flash On/FLASH ON (10M)/Flash Synchro./Flash Off  
Approx. 20 cm to 10.0 m (Wide-angle), approx. 40 cm to 6.2 m (Telephoto)  
(ISO AUTO/ISO 1600, from the front of the lens)  
Built-in flash  
Range  
Charging Time  
Approx. 8 seconds  
Picture Display  
Shooting Mode  
3.0˝ Transmissive LCD, approx. 920,000 dots  
Auto shooting mode/Scene mode (High Sens/Firefighting/Skew Correct  
Mode/Text Mode/Zoom Macro/Movie)/My settings mode/CALS mode  
F (Fine), N (Normal)  
Picture Quality Mode *1  
17  
171  
Number of Still Image  
Recorded  
4000 × 3000, 3984 × 2656, 2592 × 1944, 2048 × 1536, 1600 × 1200,  
1280 × 960, 640 × 480  
1280 × 720, 640 × 480, 320 × 240  
Pixels  
Movie  
Text  
4000 × 3000, 2048 × 1536  
Recording Media  
SD memory card, SDHC memory card (up to 32 GB), SD WORM card, Internal  
Memory (approx. 103 MB)  
Recording 4000 × 3000  
N: approx. 2713 KB/Screen, F: approx. 4735 KB/Screen  
F: approx. 4177 KB/Screen  
F: approx. 2281 KB/Screen  
F: approx. 1431 KB/Screen  
F: approx. 880 KB/Screen  
Data  
3984 × 2656  
2592 × 1944  
2048 × 1536  
1600 × 1200  
1280 × 960  
640 × 480  
Capacity  
N: approx. 363 KB/Screen, F: approx. 708 KB/Screen  
F: approx. 190 KB/Screen  
Recording Still Image  
JPEG (Exif Ver. 2.21)*2  
File Format  
Movie  
AVI (Open DML Motion JPEG Format Compliant)  
JPEG Baseline Format Compliant (Still image, movie)  
Compression  
Format  
Other Major Shooting Functions Continuous mode, Self-timer (operation time: approx. 10 seconds, approx.  
2 seconds), Interval shooting (shooting interval: 5 seconds to 3 hours, in  
increments of 5 seconds)*3, AE/AF target shift, Histogram display, Grid  
guide display, Electronic level  
Other Major Playback Functions Thumbnail view, Enlarged view (maximum 16×), Resize, Contrast  
Correction, Skew Correction, Trim, Slide show, DPOF  
Interface  
USB2.0 (High-Speed USB) Mini-B, Mass storage-compatible *4, AV output  
1.0Vp-p (75 Ω)  
Video Signal Format  
Power Supply  
NTSC, PAL  
Rechargeable Battery (DB-65): 3.6V  
DB-65: approx. 360 shots  
Battery life (based on CIPA  
standard) *5  
AAA alkaline: 40 shots *6  
(When [LCD Auto Dim] is set to [On] *7)  
118.8 mm × 71.0 mm × 41.0 mm (excluding projections; measured  
according to CIPA guidelines)  
Dimensions (W × H × D)  
Weight  
Approx. 314 g (including memory card and supplied battery)  
Approx. 286 g (camera only)  
Tripod Hole Shape  
Date Maintain Time  
Operating Temperature  
Operating Humidity  
Storage Temperature  
Water resistance/  
Dust resistance  
1/4-20UNC  
Approx. 3 days  
–10 °C to 40 °C  
90% or less  
–20 °C to 60 °C  
Camera only: JIS/IEC Class 8 water resistance, JIS/IEC Class 6 dust resistance  
(IP68)  
Camera with optional GP-1 or BR-1 attached: JIS/IEC Class 4 water  
resistance, JIS/IEC Class 6 dust resistance (IP68)  
17  
172  
*1 The picture quality mode that can be set varies depending on the image size.  
*2 Compatible with DCF and DPOF. DCF is the abbreviation for“Design rule for Camera File system,”  
a JEITA standard (Full compatibility with other devices is not guaranteed).  
*3 When the flash is set to [Flash Off].  
*4 Mass storage mode is supported by Windows 2000, Windows XP, Windows Vista, Windows 7,  
Mac OS 9.0–9.2.2, and Mac OS X 10.1.2–10.6.3.  
*5 The number of remaining shots is based on the CIPA standard and may vary depending on  
usage conditions. This is for reference only.  
*6 When using the AAA Alkaline batteries manufactured by Panasonic.  
*7 If [Off] is selected for [LCD Auto Dim], up to 345 shots can be taken with DB-65 batteries and up  
to 40 shots with AAA alkaline batteries.  
Bluetooth® Communication Port  
Communication Method  
Output  
Bluetooth® standard Ver. 2.1 + EDR  
Bluetooth® standard Power Class 2  
Approx. 10 m (line of sight)  
BIP, OPP, SPP  
Communication Range*1  
Supported Bluetooth®  
Profiles*2  
Frequency Band  
2.4 GHz (2.4 GHz – 2.4835 GHz)  
*1 The communication range may vary depending on obstructions between the two devices,  
signal strength, software or operating system in use, and other factors.  
*2 These are specifications according to the intended use of the Bluetooth®-enabled devices and  
are predetermined by Bluetooth® standards.  
Wireless LAN Communication Port  
Compliance Standard  
Transmission Method  
IEEE802.11b/g  
IEEE802.11g: OFDM  
IEEE802.11b: DSSS, DQPSK, DBPSK  
IEEE802.11g: 54M/48M/36M/24M/18M/12M/9M/6M (bps)  
IEEE802.11b: 11M/5.5M/2M/1M (bps)  
Approx. 30 m  
Data Transfer Speed*1  
Communication Range*2  
This varies depending on the location of the devices, usage environment, and  
usage conditions.  
Security Protocol  
Frequency Band  
WEP (64/128bit), WPA-PSK (TKIP/AES), WPA2-PSK (TKIP/AES)  
2.4 GHz (2.412 - 2.462 GHz)  
*1 The data transfer speeds are the maximum theoretical values based on the wireless LAN  
standard and may differ from the actual data transfer speed.  
*2 The communication range may vary depending on obstructions between the two devices,  
signal strength, location of the devices, usage environment, software or operating system in use,  
and other factors.  
17  
173  
Number of Images That Can Be Stored  
The following table shows the approximate number of images that can  
be recorded in the internal memory and onto an SD memory card at  
various image size and picture quality settings.  
Internal  
Memory  
22  
38  
25  
45  
72  
116  
141  
265  
509  
38  
Mode  
Image Size  
1 GB  
202  
351  
229  
416  
657  
1060  
1286  
2418  
4650  
351  
2 GB  
412  
714  
465  
4 GB  
810  
1403  
914  
1653  
2623  
4162  
5029  
9284  
8 GB  
1648  
2856  
1860  
3364  
5339  
8469  
16 GB 32 GB  
l4 : 3 F  
l4 : 3 N  
j3 : 2 F  
e4 : 3 F  
c4 : 3 F  
b4 : 3 F  
a4 : 3 F  
a4 : 3 N  
z4 : 3 F  
3316  
6653  
5
V
W
([Movie] and  
[Text mode]  
excluded)  
5746  
3743  
6769  
11527  
7510  
13580  
842  
1336  
2119  
2561  
4728  
8781  
714  
10743 21551  
17041 34184  
10234 20591 41306  
18894 38015 76258  
17242 35089 70600 141622  
1403  
2623  
W(Text l4 : 3  
Mode)  
2856  
5339  
5746  
11527  
c4 : 3  
72  
657  
1336  
10743 21551  
W(Movie) x1280  
3 min. 6 min. 12 min. 24 min. 50 min. 100 min.  
3 s 13 s 14 s 54 s 6 s 31 s  
8 min. 18 min. 35 min. 72 min. 145 min. 292 min.  
54 s 7 s 35 s 24 s 42 s 16 s  
20 s  
58 s  
y640  
z320  
2 min. 21 min. 43 min. 86 min. 175 min. 352 min. 707 min.  
22 s 34 s 53 s 10 s 22 s 50 s 47 s  
Note-------------------------------------------------------------------------------------  
• The figures for storage capacity assume that no camera memo lists, voice  
memos, or other camera system files are stored in the internal memory or on an  
SD memory card.  
• Fewer images can be recorded on SD WORM cards. The figures for SD WORM  
cards are given below.  
Mode  
Image Size  
l4 : 3 F  
128 MB 1 GB  
25  
198  
5
V
W
([Movie] and  
[Text mode]  
excluded)  
l4 : 3 N  
j3 : 2 F  
e4 : 3 F  
c4 : 3 F  
b4 : 3 F  
a4 : 3 F  
a4 : 3 N  
z4 : 3 F  
43  
338  
29  
229  
51  
399  
79  
614  
124  
147  
252  
412  
956  
1137  
1944  
3172  
17  
174  
• The maximum recording time is the estimated total recording time. Movies may  
be up to 4 GB in size. The maximum length is 12 minutes for movies recorded at  
a [Movie Size] of [x1280] and 29 minutes for movies recorded at [z640] or  
[y320].  
• An SD/SDHC memory card with a Speed Class of 6 or better is recommended  
when recording movies with [x1280] selected for [Movie Size] (G P.63).  
• The number of remaining shots displayed on the picture display may differ from  
the actual number of shots, depending on the subject.  
• Movie recording time and the maximum number of still pictures may vary  
depending on the capacity of the recording destination (internal memory or SD  
memory card), shooting conditions, and the type and manufacturer of the SD  
memory card.  
• Choose image size according to how the picture will be used:  
Image Size  
Description  
l4 : 3 F/l4 : 3 N/  
j3 : 2 F  
• For creating large prints.  
• For downloading to a computer for trimming and  
other processes.  
e4 : 3 F/c4 : 3 F  
b4 : 3 F/a4 : 3 F/  
a4 : 3 N  
• For creating prints.  
• For shooting a large number of pictures.  
• For shooting a large number of pictures.  
• For attaching to e-mail.  
z4 : 3 F  
• For posting on a website.  
17  
175  
Defaults Settings/Functions Whose  
Defaults Are Restored When the Camera Is  
Turned Off  
Turning the camera off may reset some function settings to their  
defaults. The table below indicates whether or not the function is reset  
to its default when the camera is turned off.  
: setting is saved ×: setting is reset  
{
Function  
Default Settings  
Shooting  
Density  
Size (Text Mode)  
Movie Size  
Picture Quality/Size  
Picture Quality/Size (Skew Correction)  
Focus  
Focus (Firefighting)  
Exposure Metering  
Continuous Mode  
Image Settings  
Auto Bracket  
Time Exposure  
Interval Shooting  
Camera Shake Correction  
Date Imprint  
Exposure Compensation  
White Balance  
ISO Setting  
Edit Detection  
Macro  
Flash  
Normal  
l4 : 3  
x1280  
l4 : 3 N  
a4 : 3 F  
Multi AF  
Snap  
Multi  
Off  
Standard  
Off  
Off  
0 Sec.  
Off  
Off  
0.0  
Auto  
Auto  
Off  
Macro Off  
Flash Off  
Off  
{
{
{
{
{
{
{
{
×
{
{
{
×
{
{
{
{
{
{
{
{
×
Self-Timer  
Playback  
Setup  
Volume Adjustment  
LCD Brightness  
Reg. My Settings  
Stepped Zoom  
ADJ Button Setting 1  
ADJ Button Setting 2  
ADJ Button Setting 3  
ADJ Button Setting 4  
—
—
—
Off  
{
{
{
{
{
{
{
{
Exposure Comp.  
White Balance  
ISO  
17  
Quality  
176  
: setting is saved ×: setting is reset  
{
Function  
Default Settings  
Setup  
AF Auxiliary Light  
Operation Sounds  
Volume Settings  
LCD Confirmation Time  
Auto Power Off  
Monitor Auto off Delay  
LCD Auto Dim  
Digital Zoom Image  
Level Setting  
Grid Guide Display Options  
Shooting Info. Display Frame  
Auto Rotate  
Card Sequence No.  
Date Settings  
Language/N  
Video Out Mode  
CALS Pic Quality  
Start Date/Time  
Choose/Change Password  
Password Protection  
Password Validity Period  
Power Button Hold Options  
On  
All  
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
„„ꢀ (Medium)  
0.5 seconds  
30 minutes  
Off  
On  
Normal  
Display  
Off  
On  
Off  
—
(
1)  
*
*
(
1)  
a4 : 3 N  
On  
—
Off  
Off  
Off  
Camera Memo Camera Memo Mode  
Memo Skip  
Mode1  
Item 2  
Off  
Off  
Off  
Off  
Off  
Off  
Mark Memo Added to Photos  
Memo Warning  
Display Memo at Startup  
Memo Increment  
Camera Memo Imprint  
Camera Memo 1 Auto Delete  
Barcode Type  
Auto  
Mode1  
3 seconds  
Barcode Mode  
Scan Time  
(
1)The default setting varies depending on where you purchased the camera.  
*
17  
177  
: setting is saved ×: setting is reset  
{
Function  
Default Settings  
Expanded  
Settings  
GPS Datum  
GPS Disp Mode  
GPS Lock  
GPS Data Select  
GPS Track Time  
WGS-84  
LAT/LON  
Off  
GPS Options  
Off  
Cardinal  
Off  
Off  
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
Compass Heading  
GPS Data Imprint  
UTC Data Imprint  
Heading Data Imprint  
Range Finder Mode  
Communication Mode  
Send Status  
Simple Connection  
Bluetooth Pass Key  
Bluetooth Search Count  
Bluetooth Auto Conn  
Bluetooth Master/Slave  
Image File Size  
Off  
Mode1  
W-LAN  
On  
Off  
—
5
Off  
Slave  
640  
Off  
Auto Delete  
Quick Send Mode  
Bluetooth Profile  
Custom Help  
Off  
OPP/BIP  
Off  
Admin Pass Key  
0000  
17  
178  
Using a Wide Conversion Lens  
A wide conversion lens (DW-5) enables  
shooting at a lens magnification of  
0.8 times (equivalent to a 35mm  
camera’s 22mm zoom in wide-angle).  
Caution---------------------------------------------------------------------------------  
• When the wide conversion lens is attached, set the zoom position to the wide-  
angle end.  
• When the wide conversion lens is attached, even if you use the internal or  
external flash, the area around the subject is not illuminated sufficiently so the  
picture will be partly underexposed.  
Note-------------------------------------------------------------------------------------  
For cleaning and storage, see the documentation that came with your wide  
conversion lens.  
Optional Filters  
Commercially-available filters with a  
diameter of 37mm can be mounted on  
the lens to protect it from damage and  
condensation.  
17  
179  
Using the External Flash  
You can attach an external flash and  
other accessories (available in stores) to  
the accessory shoe.  
You can only use an external flash  
equipped with both of the following functions.  
• Slave flash function (flash is triggered in response to the firing of  
another flash)  
• Pre-flash support function (flash is synchronized with the second  
flash instead of the pre-flash)  
Caution---------------------------------------------------------------------------------  
• The accessory shoe conforms to JIS B7101.  
• You cannot use an external flash with no spring or lock mechanism.  
• You cannot use an external flash for which synchronization with the pre-flash  
cannot be cancelled.  
Note-------------------------------------------------------------------------------------  
The accessory shoe does not support a synchronizer contact.  
17  
180  
Using Your Camera Abroad  
Battery Charger (Model BJ-6)  
The battery charger can be used in regions with a current of 100–240V, 50 Hz/60 Hz.  
If you are going to travel to a country that uses a different shaped wall outlet/plug,  
please consult your travel agent on a plug adapter suitable for wall outlets in your  
country of destination.  
Do not use electrical transformers. It may damage the camera.  
Warranty  
This product was manufactured for use in the country in which it was purchased.  
The warranty is only valid in the country in which the camera was purchased.  
Should the product fail or malfunction while you are abroad, the manufacturer  
assumes no responsibility for servicing the product locally or bearing the  
expenditure incurred therefore.  
Playback on Television in Other Regions  
Playback is possible on televisions (or monitors) equipped with a video input  
terminal. Please use the AV cable provided.  
This camera is compatible with both NTSC and PAL television formats. Set the video  
format on the camera to match that of the television you are using.  
When you go abroad, set your camera to the local video format.  
17  
181  
Cautions on Use  
Waterproofing/Dust Resistance  
• The camera complies with the JIS/IEC Class 8 standard for water resistance  
and the JIS/IEC Class 6 (IP68) standard for dust resistance. Note, however,  
that when an optional GP-1 GPS unit or BR-1 barcode reader is attached, it  
complies with the JIS/IEC Class 4 standard for water resistance only.  
• After shooting in the rain or cleaning in water, water may seep through the  
eyepiece of the lens segment and the tripod screw holes on the underside.  
This is not a problem because these sections are of double structure.  
• The internal mechanisms of the camera are neither waterproof nor dustproof.  
• Should water enter the inside of the camera, remove the batteries  
immediately and contact the Ricoh Repair Center.  
Cautions on Use  
• When opening and closing the battery/card cover or terminal cover, take  
care to prevent any water, sand, mud, dust, or other foreign matter that may  
have adhered to the camera from entering the interior of device. If possible,  
avoid opening or closing the camera at the beach, near the sea, or in sandy  
soil to prevent seawater or sand from getting inside.  
• Open and close the battery/card cover or terminal cover with your bare  
hands. Do not wear gloves, as any sand, dust, or other foreign matter that  
may have adhered to the gloves may get inside the camera. Remove any  
water, sand, mud, dust, or other foreign matter that may have adhered to  
the camera and open and close the covers in a place where it will not be  
exposed to dirt.  
• Water droplets may get inside when the cover is opened. Wipe dry before  
using.  
• Because of its waterproof structure, the mode dial may be hard to turn  
when it has not been operated for a long time. If this occurs, operate the dial  
several times to restore it to the initial state.  
• On a sandy beach or in a dusty place such as a construction site, pay  
sufficient attention to prevent sand or dust from adhering to the camera.  
• Do not leave the camera in places where there are extremes of temperature  
or humidity, such as in a closed car, at the seashore, or in a bathroom.  
• Do not force the battery/card cover or terminal cover.  
• Do not lift the camera by the battery/card cover or terminal cover.  
• If any foreign object (metal, water, liquid) gets inside the camera, stop  
using the camera immediately. Turn the power off, remove the battery and  
memory card, and consult your nearest dealer or Ricoh Repair Center.  
• In cold climates, if the camera has water droplets adhering to its surface, they  
may freeze. Using the camera with ice on it may cause it to fail. Do not leave  
the camera with water adhering to it.  
17  
182  
•
This product was manufactured for use in the country in which it was purchased.  
The warranty is only valid in the country in which the camera was purchased.  
• Should the product fail or malfunction while you are abroad, the  
manufacturer assumes no responsibility for servicing the product locally or  
bearing the expenditure incurred therefore.  
• Be sure not to drop or apply any sudden force to the camera.  
• While you are carrying the camera, be careful not to hit it against other  
objects. Take special care to not hit the lens and picture display.  
• Firing the flash consecutively may heat the firing unit. Do not fire it  
consecutively more than necessary.  
• Do not touch the flash and keep foreign objects away from the firing unit.  
Doing so can cause burns and fires.  
• Do not fire the flash near eyes. It could cause visual impairment (particularly  
for infants).  
• Do not fire the flash near the driver of a vehicle to avoid causing accidents.  
• The battery may become hot after extended use. Touching the battery  
immediately after use could result in burns to your fingers.  
• If the picture display or panel is exposed to sunlight, they may become  
washed out and images may become hard to view.  
• The picture display and panel may contain some pixels that do not remain  
lit up continually in part or at all. Also, the brightness may become uneven  
because of the characteristics of LCDs. These are not failures.  
• Do not forcefully press the surface of the picture display.  
• In an environment where the temperature changes suddenly, condensation  
may occur in the camera, resulting in troubles such as fogging of the glass  
surface or malfunctions of the camera. If this occurs, place the camera in a  
bag to slow the temperature change as much as possible. Take it out of the  
bag after the temperature difference from the atmosphere has decreased  
to a fairly small amount. If condensation occurs, remove the battery and  
memory card, and wait until the moisture has dried before using the camera.  
• To avoid damaging the connectors, do not put any objects into the camera’s  
microphone or speaker holes.  
• Before taking any important pictures (such as at weddings, on trips abroad,  
etc.), test the camera to check operation and ensure proper functioning. We  
recommend that you keep this manual and spare battery on hand.  
Conditions in which condensation may easily occur: -----------------------  
•
When the camera is moved to an environment where the temperature differs greatly.  
• In humid places.  
• In a room immediately after being heated, or when the camera is exposed  
directly to cooled air from an air-conditioner or another similar appliance.  
17  
183  
Care and Storage  
Care  
• Please note that if fingerprints, dirt, etc. get onto the lens, picture quality will suffer.  
• Any dust or dirt on the lens should be gently removed either with a blower  
(available from third-party suppliers) or a soft cloth, paying particular attention to  
the area around the lens barrel. Do not touch the lens directly with your fingers.  
• If the camera is dirty or after use at the beach, take the following steps: Make sure  
the battery/card cover and terminal cover are securely closed. Fill a wash-basin or  
bowl with tap water and use the water to remove any dirt, sand or salt from the  
camera, and then wipe the camera dry with a soft, dry cloth.  
•
If the rubber packing is dirty, wipe it clean with a soft, dry cloth. If the rubber packing  
has anything sticking to it or it is cracked or damaged, its waterproofing function may  
be compromised, resulting in leakage. If dirt cannot be removed or the packing is  
damaged, request your nearest dealer or Ricoh Repair Center to replace the packing.  
• In the unlikely event that your camera fails to work properly, please consult your  
Ricoh Repair Center.  
• There are high voltage circuits in this camera. As this is dangerous, do not  
dismantle this camera under any circumstances.  
• Do not get volatile substances, such as thinner, benzene, or pesticides on your  
camera. This may cause a change in quality, paint to peel, etc.  
•
As the surface of the picture display is easily scratched, do not rub hard objects against it.  
• Clean the surface of the picture display by wiping gently with a soft cloth  
containing a small amount of display cleaner (that does not contain organic  
solvents) sold in stores.  
Use and Storage  
• Please avoid using or storing your camera in the following kinds of places, as this  
may damage the camera.  
- In high heat and humidity, or where there is severe change in temperature or  
humidity.  
- Places with a lot of dust, dirt or sand.  
- Places with severe vibration.  
- Places where it is in direct contact with vinyl or rubber products or chemicals,  
including mothballs or other insect repellent, for long periods of time.  
- Places with strong magnetic fields (near a monitor, transformer, magnet, etc.).  
• To keep the camera free from dust and other foreign matter, store it in a lint-free  
case. Do not place it directly in a pocket or other location where it will be exposed  
to dirt or lint.  
• Remove the battery if you are not going to use the camera for a long period of  
time.  
17  
184  
Replacing the rubber packing  
To maintain the waterproof ability, replace the rubber packing every two years,  
regardless of whether it has gotten dirty. If you use the camera frequently in a wet,  
sandy, or dusty environment, we recommend replacing the packing every year. The  
replacement will be performed by the Ricoh Repair Center on a chargeable basis.  
Precautions regarding care of your camera  
1. Be sure to turn the power off.  
2. Remove the batteries before caring for your camera.  
17  
185  
Warranty and Servicing  
1. This product is backed by a limited warranty. During the warranty period mentioned  
in the Warranty supplied with your camera, any defective parts will be repaired free  
of charge. In the event of a camera malfunction, contact the dealer from which you  
purchased the camera or your nearest Ricoh Repair Center. Please note that you will be  
not be reimbursed for the cost of bringing the camera to the Ricoh Repair Center.  
2. This warranty does not cover any damage resulting from:  
failure to follow the instructions in the instruction manual;  
repair, modification or overhaul not conducted by an authorized service center listed  
in the instruction manual;  
fire, natural disaster, act of God, lightning, abnormal voltage, etc.;  
improper storage (noted in the“Camera User Guide”), leaking of battery and other  
fluids, mold, or otherwise insufficient care of the camera.  
dropping the camera or exposing it to water, mud, sand, etc. with the battery/card  
cover or terminal cover open.  
1
2
3
4
5
3. After the warranty period has passed, you will be liable for all repair fees, including those  
incurred at an authorized service center.  
4. You will be liable for all repair fees, even within the warranty period, if the warranty card is  
not attached or if the distributor's name or the purchase date have been changed or are  
not indicated on the card.  
5. Expenses for overhaul and thorough inspection by special request of the customer will be  
charged to the customer, whether or not they are incurred during the warranty period.  
6. This warranty only applies to the camera and not to the accessories, such as the case and  
strap, nor does it apply to the battery and other consumables provided.  
7. Any consequential damages arising from failure of the camera, such as expenses incurred  
in taking pictures or loss of expected profit, will not be reimbursed whether they occur  
during the warranty period or not.  
8. The warranty is only valid in the country in which the camera was purchased.  
* The above provisions refer to repairs offered free of charge, and do not limit your legal  
rights.  
* The intention of the above provisions is also described in the warranty card provided  
with this camera.  
9. Parts essential to the servicing of the camera (that is, components required to maintain  
the functions and quality of the camera) will be available for a period of five years after  
the camera is discontinued.  
10. Please note that if the camera is seriously damaged by flooding, submergence, infiltration  
of sand or mud, violent shocks or dropping, it may not be repairable, and restoration to  
its original condition may be impossible.  
Note-------------------------------------------------------------------------------------  
• Before sending the camera in for repair, check the battery and read the  
instruction manual again to ensure proper operation.  
• Some repairs require a significant amount of time to be completed.  
• When sending the camera to a service center, please include a note which  
describes the defective part and the problem as precisely as possible.  
• Remove all accessories not related to the problem before sending the camera  
to the service center.  
• This warranty does not apply to data stored on an SD memory card or in  
internal memory.  
17  
186  
Notes to users  
This Transmitter must not be co-located or operated in conjunction with any other antenna  
or transmitter.  
The available scientific evidence does not show that any health problems are associated  
with using low power wireless devices. There is no proof, however, that these low power  
wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio  
frequency energy (RF) in the microwave range while being used. Whereas high levels  
of RF can produce health effects (by heating tissue), exposure to low-level RF that does  
not produce heating effects causes no known adverse health effects. Many studies of  
lowlevel RF exposures have not found any biological effects. Some studies have suggested  
that some biological effects might occur, but such findings have not been confirmed by  
additional research. G700SE has been tested and found to comply with FCC/IC radiation  
exposure limits set forth for an uncontrolled equipment and meets the FCC radio frequency  
(RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency  
(RF) Exposure rules. Please refer to the SAR test report that was uploaded at FCC website.  
17  
187  
INFORMATION TO THE USER  
USA FCC Part 15 Class B  
This equipment has been tested and found to comply with the limits for a Class B  
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a residential installation. This  
equipment generates, uses and can radiate radio frequency energy and if not installed  
and used in accordance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in  
a particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on,  
the user is encouraged to try to correct the interference by one or more of the following  
measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment into an outlet on a circuit different from that to which the  
receiver is connected.  
• Consult the dealer or an experienced radio/TV technician for help. (FCC 15.105B)  
Changes or modifications not expressly approved by the party responsible for compliance  
could void the user's authority to operate the equipment. (FCC 15.21)  
Properly shielded and grounded cables and connectors must be used for connections to  
host computer in order to comply with FCC emission limits. (FCC 15.27)  
An AC adapter with a ferrite core must be used for RF interference suppression.  
COMPLIANCE INFORMATION STATEMENT  
Product Name: DIGITAL CAMERA  
Model Number: G700SE  
This device complies with Part 15 of the FCC Rules.  
Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference, and  
(2) This device must accept any interference received, including interference that may  
cause undesired operation.  
RICOH AMERICAS CORPORATION  
5 Dedrick Place, West Caldwell NJ, 07006 Tel.: 1-800-225-1899  
Note to Users in Canada  
Note: This Class B digital apparatus complies with Canadian ICES-003  
Remarque Concernant les Utilisateurs au Canada  
Avertissement : Cet appareil numerique de la classe B est conforme a la norme NMB-003  
du Canada  
IMPORTANT SAFETY INSTRUCTIONS-SAVE THESE INSTRUCTIONS  
DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE  
INSTRUCTIONS.  
17  
188  
Notice to Users in EEA Countries  
Declaration of Conformity  
This product complies with the essential requirements and provisions of Directive 1999/5/  
EC of the European Parliament and of the Council of 9 March 1999 on radio equipment  
and telecommunications terminal equipment and the mutual recognition of their  
conformity.  
The CE Declaration of Conformity is available on the Internet at URL:  
http://www.ricoh.com/r_dc/support/ce_docs/  
This equipment may be operated in GB, DE, BE, FR, NL, IT, LU, IE, ES, AT.  
National Restrictions  
Outdoor use of the 2.4 GHz band is prohibited in the following country:  
• France  
* Use may be prohibited in other areas also.  
Ce produit est conforme aux exigences essentielles et aux dispositions de la Directive  
1999/5/CE du Parlement européen et du Conseil du 9 mars 1999, concernant les  
équipements hertziens et les équipements terminaux de télécommunications et la  
reconnaissance mutuelle de leur conformité.  
La Déclaration de conformité CE est disponible sur Internet à l’adresse suivante :  
http://www.ricoh.com/r_dc/support/ce_docs/  
Cet équipement peut être utilisé en GB, DE, BE, FR, NL, IT, LU, IE, ES, AT.  
Restrictions nationales  
L’utilisation de la bande de fréquence 2,4 GHz en extérieur est interdite dans le pays  
suivant:  
• France  
* Il se peut que son utilisation soit également interdite dans d’autres pays.  
Dieses Produkt entspricht den Anforderungen und Vorschriften der Richtlinie 1999/5/  
EG des Europäischen Parlaments und des Rates vom 9. März 1999 über Funkanlagen  
und Telekommunikationsendeinrichtungen und die gegenseitige Anerkennung ihrer  
Konformität.  
Die CE-Konformitätserklärung ist im Internet unter folgender URL abrufbar:  
http://www.ricoh.com/r_dc/support/ce_docs/  
Dieses Gerät darf betrieben werden in: GB, DE, BE, FR, NL, IT, LU, IE, ES, AT.  
Nationale Beschränkungen  
Die Verwendung einer 2,4 GHz-Frequenz im Freien ist im folgenden Land untersagt:  
17  
• Frankreich  
* In anderen Ländern kann die Verwendung ebenfalls verboten sein.  
189  
Dit product voldoet aan de essentiële eisen en bepalingen van Richtlijn 1999/5/EG van  
het Europees Parlement en de Raad van 9 maart 1999 betreffende radioapparatuur en  
telecommunicatie-eindapparatuur en de wederzijdse erkenning van hun conformiteit.  
De EG-verklaring van conformiteit is beschikbaar via internet op de volgende URL:  
http://www.ricoh.com/r_dc/support/ce_docs/  
Dit toestel mag gebruikt worden in GB, DE, BE, FR, NL, IT, LU, IE, ES, AT.  
Nationale beperkingen  
Het gebruik van de 2,4GHz-frequentieband is verboden in:  
• Frankrijk  
* Het gebruik ervan kan ook in andere gebieden verboden zijn.  
Questo prodotto è conforme ai requisiti essenziali e alle disposizioni della Direttiva  
1999/ 5/CE del Parlamento europeo e del Consiglio, del 9 marzo 1999, riguardante le  
apparecchiature radio e le apparecchiature terminali di telecomunicazione e il reciproco  
riconoscimento della loro conformità.  
La dichiarazione CE di Conformità è disponibile su Internet all’indirizzo:  
http://www.ricoh.com/r_dc/support/ce_docs/  
Questa apparecchiatura può essere utilizzata in GB, DE, BE, FR, NL, IT, LU, IE, ES, AT.  
Restrizioni nazionali  
L’utilizzo in ambiente esterno della banda 2,4 GHz è vietato nel seguente paese:  
• Francia  
* L’utilizzo potrebbe non essere consentito anche in altre aree.  
Este producto cumple con los requisitos esenciales y cualesquiera otras disposiciones  
aplicables o exigibles de la Directiva 1999/5/CE del Parlamento Europeo y del Consejo,  
de 9 de marzo de 1999, sobre equipos radioeléctricos y equipos terminales de  
telecomunicación y reconocimiento mutuo de su conformidad.  
La Declaración de Conformidad de CE está disponible en Internet en la siguiente dirección URL:  
http://www.ricoh.com/r_dc/support/ce_docs/  
Está autorizado el uso de este equipo en GB, DE, BE, FR, NL, IT, LU, IE, ES, AT.  
Restricciones nacionales  
Está prohibido el uso en exterior de la banda de 2,4 GHz en:  
• Francia  
* Es posible que el uso también esté prohibido en otras zonas.  
17  
190  
Hinweis für Benutzer in Ländern des europäischen Wirtschaftsraumes  
Dieses Produkt befindet sich in Übereinstimmung mit den grundlegenden  
Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/  
EG des Europäischen Parlaments und des Rates vom 9. März 1999 über Funkanlagen  
und Telekommunikationsendeinrichtungen und die gegenseitige Anerkennung ihrer  
Konformität.  
Unter der folgenden URL finden Sie die offizielle Konformitätserklärung:  
http://www.ricoh.com/r_dc/support/ce_docs/  
Dieses Gerät darf in GB und DE verwendet werden.  
17  
191  
Choose/Change Password .................87, 90  
Communication Mode...............................102  
Compass Calibration ...................................101  
Compass Heading.........................................100  
Continuous Mode............................................64  
Contrast Correction.................................73, 77  
Copy to Card from Internal Memory....73  
Custom Help.............................................59, 104  
Index  
A
Accessory Shoe.......................................18, 180  
ADJ./MEMO Button.................................19, 50  
ADJ Button Setting..................................50, 84  
Admin Mode [Delete].................................104  
Admin Mode [Regist]..................................104  
Admin Pass Key...............................................104  
Adobe Reader..................................................153  
AE/AF Target Shift.............................................51  
AF Auxiliary Light......................................18, 84  
Auto Bracket ................................................64, 68  
Auto Delete.......................................................104  
Auto Focus/Flash Lamp................19, 32, 35  
Auto Power Off...........................................29, 84  
Auto Rotate..........................................................85  
Auto Shooting Mode .............................17, 31  
AV Cable.........................................................16, 81  
AV Output Terminal.................................19, 81  
D
Date Imprint ........................................................65  
Date Settings...............................................29, 86  
Delete.......................................................................41  
Delete Button..............................................19, 41  
Delete GPS Log...............................................100  
Density....................................................................63  
Digital Zoom................................................34, 89  
Digital Zoom Image........................34, 85, 89  
Direct Print.........................................................144  
DISP. Button..................................................19, 44  
Display Memo at Startup.............................96  
DL-10.......................................................... 149, 151  
DPOF ................................................................73, 80  
B
Barcode Mode....................................................97  
Barcode Reader...............................................142  
Barcode Type.......................................................97  
Battery .............................................................26, 27  
Battery/Card Cover..................................19, 27  
Battery Charger..........................................16, 26  
Bluetooth Auto Conn..................................103  
Bluetooth Master/Slave.............................103  
Bluetooth Pass Key........................................103  
Bluetooth Profile ............................................104  
Bluetooth Search Count............................103  
Bluetooth Serial ..............................................103  
BR-1........................................................................142  
E
EC1..........................................................................152  
Edit Detection.....................................................66  
Enlarged view.....................................................40  
Error Messages................................................159  
EX1..........................................................................153  
Expanded Settings Menu............................98  
Exposure Compensation .....................65, 69  
Exposure Metering ..........................................63  
External Flash...................................................180  
F
File Send.................................................................74  
Firefighting ...........................................................52  
Flash..........................................................18, 19, 35  
Focus................................................................63, 67  
Format [Card] ......................................................83  
Format [Internal Memory]...........................83  
C
CALS Mode...................................................17, 37  
CALS Pic Quality ................................................87  
Camera Memo....................................................57  
Camera Memo 1 Auto Delete...................96  
Camera Memo Imprint .................................96  
Camera Memo Menu.....................................94  
Camera Memo Mode.....................................95  
Camera Shake.....................................................33  
Camera Shake Correction............................65  
Card Sequence No...........................................86  
CD-ROM.......................................................16, 149  
G
GP-1........................................................................136  
GPS .........................................................................136  
GPS Data Imprint...........................................101  
GPS Data Select..............................................100  
GPS Datum...........................................................99  
GPS Disp Mode..................................................99  
GPS Lock.................................................................99  
192  
GPS Track Time................................................100  
Grid Guide Display...........................................44  
Grid Guide Display Options........................85  
Password Validity Period...............................87  
PictBridge...........................................................144  
Picture Display............................................19, 20  
Picture Quality/Size.........................................63  
Playback Button......................... 19, 29, 38, 72  
Playback Menu...................................................72  
Playback Mode...................................................29  
POWER Button....................................................18  
Power Button Hold Options.......................87  
Protect.............................................................73, 79  
H
Heading Data Imprint.................................101  
High Sens...............................................................52  
Histogram Display............................................48  
I
Image File Size.................................................103  
Image Settings...................................................64  
Import Communication Setting ..........102  
Internal Memory............................................174  
Interval Shooting..............................................65  
ISO Setting....................................................66, 71  
Q
Quick Send Mode..........................................104  
R
Range Finder Mode......................................101  
Rechargeable Battery.....................................26  
Recover File..........................................................74  
Reg. My Settings........................................83, 88  
Remove Memo Marking ..............................95  
Report Print.......................................................148  
Resize .......................................................................73  
Restore Defaults ................................................66  
L
Language/N ........................................29, 86  
LCD Auto Dim.....................................................84  
LCD Brightness...................................................83  
LCD Confirmation Time ................................84  
Lens...........................................................................18  
Level Indicator....................................................46  
Level Setting................................................46, 85  
List Editor............................................................151  
S
Scan Time..............................................................97  
Scene Mode (SCENE)..............................17, 52  
SDHC Card ............................................................24  
SD Memory Card............................ 24, 27, 174  
SD WORM Card..................................................24  
Self-timer .......................................................19, 36  
Send Status........................................................102  
Send To.................................................................102  
Setup Menu .........................................................82  
Shooting Info. Display Frame....................85  
Shooting Menu..................................................62  
Shutter Release Button .........................18, 31  
Simple Connection.......................................102  
Size.............................................................................63  
Skew Correction........................................73, 78  
Skew Correct Mode.................................52, 54  
Slide Show ............................................................73  
Speaker ...................................................................18  
SR-10........................................................... 120, 151  
ST-10........................................................... 113, 151  
Start Date/Time .................................................87  
Stepped Zoom...................................................83  
Strap Eyelet...........................................................18  
Synchro-Monitor Mode................................44  
M
Macro...............................................................19, 34  
Manual Focus (MF)...........................................67  
Mark Memo Added to Photos..................95  
ME1.........................................................................151  
MediaBrowser..................................................151  
Memo Increment..............................................96  
Memo Skip............................................................95  
Memo Warning..................................................95  
MENU/OK Button.......19, 62, 72, 82, 94, 98  
Microphone .........................................................18  
Mode Dial......................................................17, 18  
Monitor Auto off Delay .................................84  
Movie ...............................................................52, 55  
Movie Size.............................................................63  
My Settings Mode (MY)........................17, 37  
N
Neck strap .............................................................16  
O
Operation Sounds............................................84  
Optional Filter..................................................179  
P
Password Protection.......................29, 87, 92  
193  
T
Terminal Cover ...................................................19  
Text Mode .............................................................52  
Thumbnail View.................................................38  
Time Exposure....................................................64  
Trim ...................................................................73, 75  
Tripod Screw Hole............................................19  
TV Playback...........................................................81  
U
USB Cable...................16, 123, 144, 155, 157  
USB Terminal........................................................19  
UTC Data Imprint...........................................101  
V
Video Out Mode................................................86  
Volume Settings................................................84  
W
White Balance.............................................66, 70  
White Balance Bracket (WB-BKT)............68  
Wide Conversion Lens........................16, 179  
Z
Zoom........................................................................33  
Zoom Macro........................................................52  
194  
Telephone Support Numbers in Europe  
UK  
(from within the UK)  
(from outside the UK)  
0203 239 6327  
+44 203 239 6327  
Deutschland  
France  
Italia  
(innerhalb Deutschlands)  
(außerhalb Deutschlands)  
06331 268 438  
+49 6331 268 438  
(à partir de la France)  
(en dehors de la France)  
0800 88 18 70  
+33 1 60 60 19 94  
(dall'Italia)  
(dall'estero)  
02 4004 7319  
+39 02 4004 7319  
España  
(desde España)  
(desde fuera de España)  
900984912  
+49 6331 268 440  
http://www.service.ricohpmmc.com/  
From environmental friendliness to environmental conservation and  
to environmental management  
Ricoh is aggressively promoting environment-  
friendly activities and also environment  
conservation activities to solve the great subject  
of management as one of the citizens on our  
precious earth.  
To reduce the environmental loads of digital cameras, Ricoh is also trying to solve the great subjects  
of“Saving energy by reducing power consumption”and“Reducing environment-affecting chemical  
substances contained in products”.  
If a problem arises  
First of all, see“Troubleshooting”(G P.159) in this manual. If the issues still persist, please contact a  
Ricoh office.  
Ricoh Offices  
RICOH COMPANY, LTD.  
3-2-3, Shin-Yokohama Kouhoku-ku, Yokohama City, Kanagawa 222-8530, JAPAN  
http://www.ricoh.com/r_dc/  
RICOH AMERICAS  
CORPORATION  
5 Dedrick Place, West Caldwell, New Jersey 07006, U.S.A.  
1-800-22RICOH  
http://www.ricoh-usa.com/  
RICOH INTERNATIONAL B.V.  
(EPMMC)  
Oberrather Straße 6, D-40472 Düsseldorf, GERMANY  
(innerhalb Deutschlands)  
06331 268 438  
(außerhalb Deutschlands) +49 6331 268 438  
http://www.ricoh.com/r_dc/  
RICOH ASIA PACIFIC  
21/F, One Kowloon, 1 Wang Yuen Street, Kowloon Bay, Hong Kong  
(Toll Free) +1-800-458-4029  
UK, Germany, France and Spain: (Toll Free) +800-1532-4865  
Other Countries: +44-1489-564-764  
OPERATIONS LIMITED  
About MediaBrowser  
North America (U.S.)  
Europe  
Asia  
+63-2-438-0090  
China  
+86-21-5385-3786  
Business hours: 9:00 AM to 5:00 PM  
Ricoh Company, Ltd.  
Ricoh Building, 8-13-1, Ginza, Chuo-ku, Tokyo  
104-8222, Japan  
2010 November  
*L758 2971*  
EN USA GB GB AE AE  
Printed in Vietnam  

QSC Audio MH 1075 User Manual
Pioneer DEH P7200HD User Manual
Panasonic CQ R145U User Manual
Nokia HS 54W User Manual
Morphy Richards FP48952MEE User Manual
Maxxsonics Car Amplifier P1 6004 User Manual
Kenwood KDC C205 User Manual
Kenwood KAC 818 User Manual
Kenwood Car Stereo System krc 669 User Manual
Kenwood Car Amplifier KAC 648 User Manual