Remington 100089 01 User Manual

®
ELECTRIC CHAIN SAW  
OWNER’S MANUAL  
®
®
MODELS  
LNT-2: 076728J, 100089-06, & 099178H  
EL-1, EL-1 Fast Sharp  
EL-7: 075762J, 098031J, 099039J, 100015,  
100089-01, 100089-04, 100089-05, & 100089-07  
EL-7 Fast Sharp: 076702J  
Pole Saw: 104316-01  
Pole Saw Assembly: 104317  
IMPORTANT:Readandunderstandthismanualbeforeassemblingor  
operating this chain saw. Improper use of saw can cause severe  
injury. Keep this manual for future reference.  
®
OWNER’S MANUAL  
MAINTENANCE AND  
STORAGE OF CHAIN SAW  
1. Unplug chain saw from power source  
• when not in use  
SAFETY  
WARNINGS  
KICKBACK  
• before moving from one place to an-  
other  
WARNING: Kickback may oc-  
cur when the nose or tip of the  
guide bar touches an object, or  
when the wood closes in and  
pinches the saw chain in the cut.  
Tip contact in some cases may  
cause a lightning fast reverse re-  
action, kicking the guide bar up  
and back towards the operator.  
Pinching the saw chain along the  
topoftheguidebarmaypushthe  
guide bar rapidly back towards  
the operator. Either of these re-  
actions may cause you to lose  
control of the saw which could  
result in serious injury to user.  
• before servicing  
• before changing accessories or at-  
tachments, such as saw chain and  
guard  
Direction  
2. Inspect chain saw before and after each  
Do Not Let  
Guide Bar  
Touch Here  
use. Check saw closely if guard or other  
part has been damaged. Check for any  
damage that may affect operator safety  
or operation of saw. Check for align-  
ment or binding of moving parts. Check  
for broken or damaged parts. Do not  
use chain saw if damage affects safety  
or operation. Have damage repaired by  
authorized service center.  
90°  
Quadrant  
3. Maintain chain saw with care.  
• Never expose saw to rain.  
• Keep chain sharp, clean, and lubri-  
cated for better and safer performance.  
• Follow steps outlined in this manual  
to sharpen chain.  
Figure 1 - Kickback Hazard Example: Do  
Not Let Nose of Guide Bar Touch Object  
While Chain is Moving  
Kickback Safety Devices On  
This Saw  
This saw has a low-kickback chain and  
reduced kickback guide bar. Both items  
reduce the chance of kickback. Kickback  
can still occur with this saw.  
• Never try cutting through two logs at  
same time. Only cut one log at a time.  
• Keep handles dry, clean, and free of  
oil and grease.  
• Keep all screws and nuts tight.  
• Inspect power cord often. If dam-  
aged, have repaired by authorized  
service center.  
• Never carry chain saw by power  
cord.  
• Never yank power cord to unplug it.  
• Keep power cord from heat, oil, and  
sharp edges.  
• Do not bury guide bar nose or try plunge  
cut (boring into wood using guide bar  
nose).  
Properly install front hand guard. This item  
can reduce injuries from kickback. Follow  
assembly instructions on page 6. Do not  
remove front hand guard. Do not replace  
front hand guard with substitute.  
• Watch for shifting of wood or other  
forces that may pinch chain.  
• Use extreme caution when re-entering a  
previous cut.  
The following steps will reduce the risk of  
kickback.  
• Use low-kickback chain and guide bar  
supplied with this chain saw. Only re-  
place these parts with chains and guide  
bars listed in this manual.  
• Use both hands to grip saw while saw is  
running. Use firm grip. Thumbs and  
fingers must wrap around saw handles.  
• Inspect extension cords often and  
replace if damaged.  
4. When servicing, use only identical re-  
placement parts.  
• Never use dull or loose chain. Keep chain  
sharp with proper tension.  
• Keep all safety items in place on saw.  
Make sure they work properly.  
5. When not in use, always store chain saw  
• in a high or locked place, out of  
children’s reach  
• Do not hand sharpen chain on automatic  
chain sharpening (Fast Sharp) models.  
• Do not overreach or cut above shoulder  
height.  
• Keep solid footing and balance at all  
times  
• in a dry place  
• in a carrying case or with scabbard  
over guide bar  
Saw Maintenance and Kickback  
Safety  
• Stand slightly to left side of saw. This  
keeps your body from being in direct line  
with chain.  
Follow maintenance instructions in this  
manual. Proper cleaning of saw and chain  
and guide bar maintenance can reduce  
chances of kickback. Inspect and maintain  
saw after each use. This will increase the  
service life of your saw. Note: Even with  
proper sharpening, risk of kickback can  
increase with each sharpening.  
Keep this manual for reference. It is your  
guide to safe and proper operation of this  
chain saw.  
• Do not let guide bar nose touch anything  
when chain is moving (see Figure 1).  
097017  
3
®
ELECTRIC CHAIN SAW  
Replacement Chain Chain that com-  
CHAIN SAW NAMES  
AND TERMS  
plies with ANSI B175.1 when used with a  
specific saw. It may not meet ANSI require-  
ments when used with other saws.  
Bucking Process of cutting a felled tree or  
SawChain(Chain) Loopofchainhaving  
cutting teeth for cutting wood. The motor  
drives chain. The guide bar supports chain.  
log into lengths.  
Felling Process of cutting down a tree.  
Felling Cut Final cut when felling a tree.  
Make this cut on opposite side of tree from  
notching cut.  
SpikedBumper(Spike) Pointed teeth at  
front of saw body beside guide bar. Keep  
spiked bumper in contact with wood when  
felling or bucking. It helps maintain posi-  
tion of saw while cutting.  
FrontHandle Locatedatfrontofsawbody.  
Front Hand Guard Shield between front  
handle and guide bar. Protects left hand  
while using saw.  
Sprocket Toothedwheelthatdriveschain.  
Switch Devicethatcompletesorinterrupts  
electrical circuit to motor of saw.  
Guide Bar Metal bar that extends from saw  
body.Theguidebarsupportsandguideschain.  
Switch Linkage This device connects  
switch to trigger. It moves switch when you  
squeeze trigger.  
Guide Bar Nose Tip or end of guide bar.  
Kickback Quick backward and upward  
motion of guide bar. Kickback may occur  
when tip of guide bar touches an object  
while chain is moving. The guide bar will  
kick up and back towards operator.  
Switch Lockout Device that reduces  
accidental starting of saw.  
Trigger Device that turns saw on and off.  
Squeezing trigger turns saw on.  
Limbing Process of cutting limb(s) from a  
felled tree.  
Releasing trigger turns saw off.  
Trimming (Pruning) Process of cutting  
limb(s) from a living tree.  
Low-Kickback Chain Chain that re-  
duces chance of kickback as required by  
ANSI B175.1.  
Undercut An upward cut from underside  
of log or limb. This is done while in normal  
cutting position and cutting with top of  
guide bar.  
Normal Cutting Position Stance used  
while making bucking and felling cuts.  
Notching Cut Notch cut in tree that di-  
rects fall of tree.  
Oiler Control System for oiling guide bar  
and chain.  
PowerHead Chainsawwithoutchainand  
guide bar. Also known as saw body.  
Pushback (Kickback, Pinch) Rapid  
pushback of chain saw. Pushback may oc-  
curifchainalongtopofguidebarispinched,  
caught, or contacts a foreign object.  
RearHandle Handlelocatedatrearofsaw  
body.  
Reduced Kickback Guide Bar Guide  
bar that reduces chance of kickback.  
097017  
4
OWNER’S MANUAL  
PRODUCT  
UNPACKING  
Front Hand  
Guard  
IDENTIFICATION  
1. Remove all items from carton.  
Guide Bar  
Nose  
2. Check all items for any shipping dam-  
age. If you find any damage or if any  
parts are missing, promptly inform  
dealer where you bought chain saw.  
Saw  
Chain  
Rear  
Handle  
Guide Bar  
Spike  
Rear Hand  
Guard  
Scabbard  
Power Cord  
Oil Level Sight Hole  
(located on saw body,  
hidden by front handle)  
Oil Cap  
Front Handle  
Switch  
Lockout  
Trigger  
Motor  
Housing  
Figure 2 - Electric Chain Saw  
097017  
5
®
ELECTRIC CHAIN SAW  
8. Place chain around drive sprocket, then  
ASSEMBLY  
CAUTION: Do not place chain  
on saw backwards. If chain is  
backwards,sawwillvibratebadly  
and will not cut.  
along top groove of guide bar and  
around guide bar nose. Note: Make  
sure cutting edges of chain are facing  
the right direction. Position chain so  
cutting edges on top of guide bar face  
guide bar nose (see Figure 3).  
Note: Some models are pre assembled. As-  
sembly is not needed on these models.  
See Saw Chain Tension Adjustment, page 7.  
9. Adjust saw chain tension. Follow steps  
under Saw Chain Tension Adjustment,  
page 7.  
WARNING: Cutting edges on  
chain are sharp. Use protective  
gloves when handling chain.  
Tapping  
Screw  
Front Hand  
Guard  
Towards  
Guide  
Cutting  
Edge  
IMPORTANT:Donotclampchain  
saw in vise during assembly.  
Bar Nose  
The plastic hardware bag should include:  
• two guide bar bolts  
Saw  
Chain  
Cutting  
Edge  
• two guide bar nuts  
Guide Bar  
Bolts  
• one Phillips-head tapping screw  
• automatic chain sharpener (Fast Sharp  
models only)  
Drive  
Sprocket  
1. Lay chain out flat.  
Mounting  
Stand-Outs  
2. Install front hand guard onto saw body.  
Do this by pressing two mounting stand-  
outs on hand guard into hex-shaped  
holes in saw body (see Figure 3).  
3
Insert tapping screw through hand  
guard and into saw handle. Tighten  
screw firmly.  
Guide  
Bar  
4. Turn adjusting screw counterclockwise  
(see Figure 4). Continue to turn adjust-  
ing screw until adjusting block is to rear  
of adjusting plate.  
Adjusting  
Hole  
Guide Bar  
Nuts  
5. Install guide bar onto saw body. Place  
rear of guide bar between adjusting  
plate and sprocket support.  
IMPORTANT: Make sure to insert ad-  
justing block into oval adjusting hole  
on guide bar.  
Figure 3 - Assembling Guide Bar, Chain, and Hand Guard  
6. Line up holes on sprocket support with  
center slot on guide bar and holes in  
saw body.  
Adjusting  
Block  
Adjusting  
Plate  
7. Insert guide bar bolts through front  
hand guard, saw body, center slot of  
guide bar, and sprocket support.Attach  
guide bar nuts to guide bar bolts.  
Adjusting  
Screw  
IMPORTANT: Tighten guide bar nuts  
finger tight only. Make sure adjust-  
ing block is in oval adjusting hole on  
guide bar.  
Sprocket  
Support  
Figure 4 - Part Locations For Assembling Guide Bar  
097017  
6
OWNER’S MANUAL  
ASSEMBLY  
SAW CHAIN  
TENSION  
Continued  
ADJUSTMENT  
INSTALLING AUTOMATIC  
CHAIN SHARPENER  
WARNING:Unplugchainsaw  
frompowersourcebeforeadjust-  
ing saw chain tension.  
(Fast Sharp Models Only)  
1. Screw automatic chain sharpener into  
threaded hole.  
2. Continue turning automatic chain  
sharpener until you hear five (5) clicks.  
WARNING: Cutting edges on  
chain are sharp. Use protective  
gloves when handling chain.  
Automatic  
Chain  
Sharpener  
WARNING: Maintain proper  
chain tension always. A loose  
chain will increase the risk of  
kickback.Aloosechainmayjump  
outofguidebargroove.Thismay  
injure operator and damage  
chain. A loose chain will cause  
chain, guide bar, and sprocket to  
wear rapidly.  
PUSH  
Figure 6 - Turning Adjusting Screw  
SHARPTEON  
Guide Bar  
Nuts  
Note: For pre assembled models, the saw  
chain tension is properly set at factory. A  
new chain will stretch. Check new chain  
after first few minutes of operation. Allow  
chain to cool down. Follow steps below to  
readjust saw chain tension.  
Guide Bar  
Figure 5 - Automatic Chain Sharpener  
(Fast Sharp Models Only)  
1. Before adjusting chain, make sure guide  
bar nuts are only finger tight (see Figure  
3, page 6). Also make sure adjusting  
block is in oval adjusting hole on guide  
bar (see Figures 3 and 4, page 6).  
Guide Bar  
Correct  
Tension  
Gap  
2. Turn adjusting screw clockwise until  
all slack is out of chain (see Figure 6).  
Note: There should be no gap between  
side links of chain and bottom of guide  
bar (see Figure 7).  
Incorrect  
Tension  
Figure 7 - Saw Chain Adjustment  
3. Wearing protective gloves, move chain  
around guide bar. Chain should move  
freely. If chain does not move freely,  
loosen chain by turning adjusting screw  
counterclockwise.  
FILLING OIL TANK  
1. Remove oil cap.  
2. Fill oil tank with SAE #30 motor oil.  
Note: For temperatures below 30°F, use  
SAE #10 oil. For temperatures above  
75°F, use SAE #40 oil.  
3. Replace oil cap at once. Tighten oil cap  
firmly for good seal. This will avoid oil  
seepage from tank.  
4. After chain tension is correct, tighten  
guide bar nuts firmly. If not, guide bar  
will move and loosen chain tension.  
This will increase the risk of kickback.  
This can also damage saw. Note:Anew  
chain will stretch. Check new chain  
after first few minutes of operation.  
Allow chain to cool down. Readjust  
chain tension.  
4. Wipe off excess oil.  
Note: It is normal for oil to seep when saw  
is not in use. Empty oil tank after each use to  
prevent seepage.  
097017  
7
®
ELECTRIC CHAIN SAW  
5. When ready to make a cut, press in  
switch lockout with right thumb and  
squeeze trigger (see Figure 10). This  
will turn saw on. Releasing trigger will  
turn saw off. Make sure saw is running  
at full speed before starting a cut.  
OILING CHAIN  
OPERATING CHAIN  
Always check oil level before using saw. To  
SAW  
oil chain, press oil cap. Do not attempt to  
operate the oiler while cutting with the saw.  
Oil will feed onto guide bar and chain. Press  
oilcapatleastoncebeforeeachcut.Checkoil  
level often by looking at oil sight level hole.  
Oil sight level hole is on left side of saw,  
between front handle and front hand guard.  
WARNING: Read and under-  
stand this owner’s manual before  
operating this saw. Make certain  
youreadandunderstandallSafety  
Warnings,pages2and3.Improper  
use of this chain saw can cause  
severe injury or death from fire,  
electrical shock, or body contact  
withmovingchain,orfallingwood.  
Switch  
Lockout  
EXTENSION CORDS  
Use proper extension cords with this saw.  
Use only extension cords marked for out-  
door use. The cord must be marked with  
suffix W or W-A following the cord type  
designation. Example: SJTW-A or SJTW.  
Trigger  
Figure 10 - Switch Lockout and Trigger  
Location  
Figure 9 - Pressing Oil Cap to Oil Chain  
Use proper sized cord with this saw. Cord  
must be heavy enough to carry current  
needed. An undersized cord will cause volt-  
age drop at saw. Saw will lose power and  
overheat. Follow cord size requirements  
listed below.  
6. When starting a cut, place moving  
chain against wood. Hold saw firmly  
in place to avoid possible bouncing or  
skating (sideways movement) of saw.  
CUTTING WITH THE CHAIN  
SAW  
1. Connect saw to extension cord. Con-  
nect extension cord to power supply.  
7. Guide saw using light pressure. Do not  
force saw. The motor will overload and  
can burn out. It will do the job better and  
safer at the rate for which it was intended.  
Cord  
Length  
AWG Cord  
Size  
2. Make sure section of log to be cut is  
not laying on ground. This will keep  
chain from touching ground as it cuts  
through log. Touching ground with  
moving chain will dull chain.  
25 feet  
50 feet  
100 feet  
16  
16  
14  
12  
8. Remove saw from a cut with saw run-  
ning at full speed. Stop saw by releas-  
ing trigger. Make sure chain has  
stopped before setting saw down.  
150 feet  
3. Use both hands to grip saw.Always use  
left hand to grip front handle and right  
hand to grip rear handle. Use firm grip.  
Thumbs and fingers must wrap around  
saw handles (see Figure 10).  
9. Practice until you can maintain a steady,  
even cutting rate.  
Keep cord away from cutting area. Make  
sure cord does not catch on branches or logs  
during cutting. Inspect cords often. Replace  
damaged cords.  
4. Make sure your footing is firm. Keep  
feet apart. Divide your weight evenly  
on both feet.  
The extension cord may come undone from  
the power cord during use. To avoid this,  
make a knot with the two cords as shown in  
Figure 8 below.  
Chain Saw  
Power Cord  
Extension  
Cord  
Figure 8 - Tying Extension Cord and  
Power Cord in Knot  
097017  
8
OWNER’S MANUAL  
Direction  
of Fall  
OPERATING CHAIN  
Retreat  
Path  
SAW  
Hinge  
Direction  
of Fall  
3rd Cut -  
Felling Cut  
Continued  
2nd Cut -  
Upper  
Notch Cut  
FELLING A TREE  
(Cutting Down a Tree)  
2
Inches  
45°  
2"  
WARNING:  
1st Cut -  
Lower  
Notch Cut  
Retreat  
Path  
Tree  
• Avoid kickback. Kickback can  
resultinsevereinjuryordeath.  
See Kickback, page 3 to avoid  
risk of kickback.  
Figure 11 - Retreat Path From Tree  
Felling Procedure  
A) Felling Notch  
• Donotfellatreewithoutample  
skill or expert help.  
• Keep children, animals, and  
bystanders away from area  
when felling a tree.  
• If two or more persons perform  
bucking and felling operations  
A properly placed felling notch will deter-  
mine direction tree will fall. Place felling  
notch on side of tree in direction you want  
tree to fall (see Figure 12). Follow direc-  
tions below to create a felling notch.  
Figure 12 - Felling A Tree  
3. As felling cut nears hinge, tree should  
begin to fall. Note: If needed, drive  
wedges into felling cut to control di-  
rection of fall. If tree settles back and  
pinches chain, drive wedges into fell-  
ing cut to remove saw. Only use wedges  
made of wood, plastic, or aluminum.  
Never use wedge made of steel. This  
could cause kickback and damage to  
chain.  
1. Make lower notch cut as close to  
ground as possible. Hold saw so guide  
bar is horizontal. Cut 1/3 the diameter  
of tree trunk (see Figure 12). Note:Al-  
ways make this horizontal lower notch  
cut first. If you make this cut second,  
tree can pinch chain or guide bar.  
WARNING: When felling a  
tree, be aware of your surround-  
ings. Do not endanger any per-  
son, strike utility lines, or cause  
property damage. If tree strikes  
utility lines, contact utility com-  
pany at once.  
4. When tree begins to fall, quickly  
• remove saw from felling cut  
• release trigger to turn saw off  
• put saw down  
2. Start upper notch cut the same distance  
above first cut as first cut is deep.  
Felling is the process of cutting down a tree.  
Make sure your footing is firm. Keep feet  
apart. Divide your weight evenly on both  
feet. Follow directions below to fell a tree.  
Example: If lower notch cut is eight  
inches deep, start upper notch cut eight  
inches above it. Cut downward at 45°  
angle. The upper notch cut should meet  
end of lower notch cut (see Figure 12).  
• exit area using retreat path  
Before Felling a Tree  
WARNING: Be alert for falling  
overheadlimbs.Watchyourfoot-  
ing while exiting area.  
3. Remove tree trunk wedge created by  
notching cuts.  
1. Before felling, inspect tree. Make sure  
there are no dead limbs or branches that  
may fall on you. Study natural lean of  
tree, location of larger branches, and  
B) Felling Cut  
wind direction. This will help you judge 1. Make felling cut two inches higher than  
which way tree will fall.  
lower notch cut and on opposite side  
of tree (see Figure 12). Keep felling cut  
parallel to lower notch cut.  
2. Clear work area around tree.  
3. Plan and clear a retreat path before fell-  
ing. Make retreat path opposite to  
planned direction of fall of tree and at  
45° angle (see Figure 11).  
4. Remove dirt, stones, loose bark, nails,  
staples, and wire from tree where you  
will make felling cuts.  
2. Cut towards notch.  
WARNING: Do not cut all the  
way through tree. Leave about  
two inches of tree diameter un-  
cut directly behind felling notch  
(see Figure 12). This uncut por-  
tion acts as a hinge. The hinge  
helpskeeptreefromtwistingand  
falling in wrong direction.  
5. Stay on uphill side when felling tree.  
Tree could roll or slide downhill after  
falling.  
Continued  
097017  
9
®
ELECTRIC CHAIN SAW  
Entire Length Of Log On  
Ground  
Cut log from top (see Figure 14).  
BUCKING A LOG  
OPERATING CHAIN  
SAW  
WARNING: Avoid kickback.  
Continued  
Kickback can result in severe in-  
juryordeath.SeeKickback,page  
3 to avoid risk of kickback.  
LIMBING A TREE  
WARNING: Avoid kickback.  
WARNING:  
Kickback can result in severe in-  
juryordeath.SeeKickback,page  
3 to avoid risk of kickback.  
• If on slope, make sure log will  
not roll down hill. Secure log  
byusingwoodenstakes. Drive  
wooden stakes into ground on  
downhill side of log. Stand on  
uphill side of log while cutting.  
Log may roll after cutting.  
• Never try cutting through two  
logs at same time. This could  
increase the risk of kickback.  
• While cutting log, never hold  
logwithyourhand,leg,orfoot.  
• While cutting log, never allow  
another person to hold log.  
• Turn off and unplug saw be-  
fore moving from one place to  
another.  
WARNING:Whencuttinglimb  
thatisundertension,useextreme  
caution.Bealertforwoodspring-  
ing back. When wood tension is  
released, limb could spring back  
and strike operator causing se-  
vere injury or death.  
Figure 14 - Bucking Log With Entire  
Length On Ground  
Limbingisremovingbranchesfromafallen  
tree. Make sure your footing is firm. Keep  
feet apart. Divide your weight evenly on  
both feet. Do not remove larger limbs under  
tree that support log off ground. Remove  
each limb with one cut (see Figure 13).  
Clear cut limbs from work area often. This  
will help maintain a safe work area.  
Log Supported On One End  
1. Make first cut on underside of log (see  
Figure 15). Use top of guide bar to  
make this cut. Cut 1/3 through diam-  
eter of log. This cut will keep section  
from splintering when cut.  
Bucking a log is cutting a log into sections.  
Make sure your footing is firm. Keep feet  
apart. Divide your weight evenly on both feet.  
Whenpossible,raiselogorsectionoffground.  
Do this by using limbs, logs, chocks, etc.  
2. Make second cut directly above first  
cut. Cut down to meet first cut. This  
cut will keep log from pinching guide  
bar and chain.  
Make sure you start your cut where limb  
will not pinch saw during cutting. To avoid  
pinching, start cut on freely hanging limbs  
from above limb. Start cut on limbs under  
tension from under limb. If pinch occurs,  
turn saw off, lift limb, and remove saw.  
When cutting through log, maintain control  
byreducingcuttingpressurenearendofcut.  
Donotrelaxyourgriponchainsawhandles.  
Do not let moving chain touch ground.  
Ground will dull moving chain. After cut-  
ting through log, release trigger to turn saw  
off before moving saw.  
2nd Cut  
Follow directions below to buck a log.  
1st Cut  
Figure 15 - Bucking Log When Log Is  
Supported On One End  
Figure 13 - Limbing A Tree  
097017  
10  
OWNER’S MANUAL  
2nd Cut -  
Pruning Cut  
(to avoid pinching)  
TRIMMING A TREE (Pruning)  
OPERATING CHAIN  
4th Cut -  
Final Stub  
Cut  
SAW  
WARNING: Avoid kickback.  
Kickback can result in severe in-  
juryordeath.SeeKickback,page  
3 to avoid risk of kickback.  
Continued  
Log Supported On Both Ends  
1. Make first cut from above log (see Fig-  
ure 16). Cut 1/3 through diameter of  
log. This cut will keep section from  
splintering when cut.  
6"  
WARNING: Do not operate  
chain saw while  
• in a tree  
• on a ladder or any other un-  
stable surface  
• in any awkward position  
Youmaylosecontrolofsawcaus-  
ing severe injury.  
2" to 4"  
2. Make second cut on underside of log,  
directly under first cut. Use top of guide  
bar to make this cut. Cut up to meet  
first cut. This will keep log from pinch-  
ing guide bar and chain.  
1st Cut -  
Pruning Undercut  
(to avoid splintering)  
3rd Cut - Stub Undercut  
(to avoid splintering)  
WARNING: Do not cut limbs  
higher than your shoulders.  
1st Cut  
Figure 17 - Cutting A Limb  
CAUTION: Seek professional  
help if facing conditions beyond  
your ability.  
Trimming a tree is the process of cutting  
limbs from a living tree. Make sure your  
footing is firm. Keep feet apart. Divide your  
weight evenly on both feet. Follow direc-  
tions below to trim a tree.  
1. Make first cut six inches from tree trunk  
on underside of limb. Use top of guide  
bar to make this cut. Cut 1/3 through  
diameter of limb (see Figure 17).  
2nd Cut  
Figure 16 - Bucking Log When Log Is  
Supported On Both Ends  
2. Move two to four inches farther out on  
limb. Make second cut from above limb.  
Continue cut until you cut limb off.  
3. Make third cut as close to tree trunk as  
possible on underside of limb stub. Use  
top of guide bar to make this cut. Cut  
1/3 through diameter of stub.  
4. Make fourth cut directly above third  
cut. Cut down to meet third cut. This  
will remove limb stub.  
097017  
11  
®
ELECTRIC CHAIN SAW  
Normal Guide Bar Maintenance  
1. Remove guide bar from chain saw.  
CARE OF GUIDE BAR  
CLEANING AND  
MAINTENANCE  
Uneven bar wear causes most guide bar  
problems. Incorrect sharpening of chain  
cutter and depth gauge settings often cause  
this. When bar wears unevenly, it widens  
guidebargroove(seeFigure18).Thiscauses  
chainclatterandrivetpopping. Sawwillnot  
cutstraight.Replaceguidebarifthisoccurs.  
2. Remove sawdust from guide bar  
groove periodically. Use putty knife or  
wire.  
NOTICE: Below are instructions  
forservicingyourchainsaw.Any  
servicing not mentioned below  
should be done by an authorized  
service center.  
3. Clean oil slots after each day of use.  
4. Remove burrs from sides of guide bar.  
Use flat file to make side edges square.  
Inspect guide bar before sharpening chain.  
A worn or damaged guide bar is unsafe. A  
worn or damaged guide bar will damage  
chain. It will also make cutting harder.  
Replace guide bar when  
• bar is bent or cracked  
CLEANING SAW BODY  
• inside groove of bar is badly worn  
WARNING: Unplug chain saw  
from power source before servic-  
ing. Severe injury or death could  
occur from electrical shock or  
body contact with moving chain.  
Note: When replacing guide bar, see Re-  
placement Parts and Accessories, on back  
cover, for proper bar.  
Guide Bar  
Groove  
Burr  
WARNING: Cutting edges on  
chain are sharp. Use protective  
gloves when handling chain.  
Guide Bar  
WARNING: When cleaning  
saw body,  
• do not submerge saw in any  
liquids  
Flat File  
• do not use products that con-  
tain ammonia, chlorine, or  
abrasives  
• do not use chlorinated clean-  
ingsolvents,carbontetrachlo-  
ride, kerosene, or gasoline  
Guide Bar  
Guide Bar  
With Uneven  
Normal Guide  
Cleaning Groove With  
Putty Knife  
Bar  
Wear  
Figure18-GuideBarCrossSectionShow-  
ing Uneven Bar Wear  
Keepsawbodyclean.Useasoftclothdamp-  
ened with a mild soap and water mixture.  
Wipe saw body to clean.  
Oil Slot  
Figure 19 - Guide Bar Maintenance  
097017  
12  
OWNER’S MANUAL  
4. Hold file guide level. Make sure 30°  
mark on file guide is parallel to center  
of guide bar (see Figure 20). This will  
Sharpening Cutters  
CLEANING AND  
Use file guide for 30° filing.  
1. Adjust chain for proper tension (see Saw  
MAINTENANCE  
insure that you file cutters at 30° angle.  
Continued  
Chain Tension Adjustment, page 7).  
5. File from inside towards outside of cut-  
ter until sharp. Only file in this one direc-  
tion (see Figure 20). Note: Two or three  
strokes with file should sharpen cutter.  
2. Clamp guide bar in vise to hold saw  
SHARPENING SAW CHAIN  
(Non-Fast Sharp Model)  
steady. Note: Do not clamp chain.  
3. Press 5/32" round file (attached to file  
guide) into groove between top plate  
and depth gauge on chain. File guide  
should rest on both top plate and depth  
gauge (see Figures 20 and 21). Note:  
File at midpoint of guide bar.  
6. After each cutter if sharpened, move  
chain forward to sharpen next cutter.  
File all cutters on one side of chain.  
WARNING: Unplug chain saw  
from power source before servic-  
ing. Severe injury or death could  
occur from electrical shock or  
body contact with moving chain.  
7. Move to other side of chain and repeat  
process.  
Filing  
Direction  
WARNING: Cutting edges on  
chain are sharp. Use protective  
gloves when handling chain.  
30° Guide  
Mark  
File  
Guide  
Keep chain sharp. Your saw will cut faster  
and more safely. A dull chain will cause  
undue sprocket, guide bar, chain, and motor  
wear. If you must force chain into wood and  
cutting creates only sawdust with few large  
chips, chain is dull.  
5/32"  
Round File  
Items Needed to Sharpen Chain  
Note: This illustration  
Purchasetheseitemsfromyourlocaldealer,  
hardwarestore,orchainsawsuppliesoutlet.  
shows file guide  
placement and filing  
direction for sharpen-  
ing cutters on left side  
of chain.  
• 5/32" round file  
• Depth gauge tool  
• File guide  
• Vise  
Figure 20 - File and File Guide Placement On Chain  
• Medium sized flat file  
Groove  
Depth Gauge  
(left side of chain)  
Left Side of  
Chain  
Depth Gauge  
(right side  
of chain)  
Groove  
Top Plate  
(right side of chain)  
Top Plate  
(left side of chain)  
Right Side of  
Chain  
Figure 21 - Chain Part Locations  
Continued  
097017  
13  
®
ELECTRIC CHAIN SAW  
5. Place saw on clean, flat surface.  
6. Connect saw to power supply.  
SHARPENING SAW CHAIN  
(Fast Sharp Model)  
CLEANING AND  
MAINTENANCE  
7. Hold saw, with both hands in normal  
cutting position.  
Continued  
WARNING: Unplug chain saw  
8. Press in switch lockout with right  
thumb and squeeze trigger.  
from power source before servic-  
ing. Severe injury or death could  
occur from electrical shock or  
body contact with moving chain.  
Filing Cutter Depth Gauges  
The cutter depth gauge clearance is reduced  
as cutters are sharpened. After every second  
orthirdsharpening,resetcutterdepthgauges.  
9. Gently push on sharpener knob. Saw  
must be running for chain to sharpen.  
Note: Sparks appearing shows sharp-  
ener is working (see Figure 25). If no  
sparks appear, continue to adjust sharp-  
ener one click at a time. After each  
click, press sharpener knob until light  
flow of sparks appears.  
1. Place depth gauge tool (.025") firmly  
across top of two cutters. Make sure  
depth gauge enters slot in depth gauge  
tool (see Figure 22).  
WARNING: Cutting edges on  
chain are sharp. Use protective  
gloves when handling chain.  
2. Use medium flat file. File depth gauge  
level with depth gauge tool.  
WARNING: Do not hand-  
sharpen this Fast Sharp chain.  
Hand-sharpening chain will in-  
crease risk of kickback.  
After several sharpenings, you must turn  
sharpener knob more to bring stone into  
position.  
3. Remove depth gauge tool. With flat file,  
round off front corner of cutter depth  
gauge (see Figure 23).  
After several hand filings, have authorized  
servicecenterorsharpeningservicemachine  
sharpen chain. This will insure even filing.  
Keep chain sharp. Your saw will cut faster  
and more safely. A dull chain will cause  
undue sprocket, guide bar, chain, and motor  
wear. If you must force chain into wood and  
cutting creates only sawdust with few large  
chips, chain is dull.  
Flat File  
Depth Gauge  
Follow the steps below to sharpen Fast  
Sharpchain. Theautomaticchainsharpener  
sharpens cutter, lowers cutter depth gauge,  
and adjusts guard drive link.  
Figure 25 - Sharpening Fast Sharp Chain  
Depth  
Gauge  
Tool  
1. Adjust saw chain for proper tension  
(see Saw Chain Tension Adjustment,  
page 7).  
REPLACING SAW CHAIN  
Replace chain when cutters are too worn to  
sharpen or when chain breaks. Only use  
replacement chain noted in this manual.  
Always include new drive sprocket when  
replacing chain. This will maintain proper  
drivingofchain.Note:Forproperchainand  
drive sprocket, see Replacement Parts and  
Accessories, on back cover.  
2. Clean out excess sawdust and wood  
chips from drive sprocket area.  
Depth  
Gauge  
Slot  
3. Turn sharpener knob counterclockwise  
until clicking stops (see Figure 24).  
4. Turn sharpener knob clockwise until  
you hear five distinct clicks.  
Figure 22 - Depth Gauge Tool On Chain  
Front Corner  
.025"  
PUSH  
SHARPTEON  
Figure 23 - Round Off Front Corner Of  
Depth Gauge  
Sharpener  
Knob  
Figure 24 - Turning Sharpener Knob  
097017  
14  
OWNER’S MANUAL  
TROUBLESHOOTING  
WARNING: Unplug chain saw from power source before servicing.  
Severe injury or death could occur from electrical shock or body contact  
with moving chain.  
OBSERVED FAULT  
POSSIBLE CAUSE  
REMEDY  
Saw runs, but does not cut.  
Chain assembled backwards on guide bar  
See Assembly, page 6  
Saw does not cut unless heavily forced. Chain is dull  
Cutting produces only sawdust with few  
large chips.  
See Sharpening Saw Chain, page 13 (non-  
Fast Sharp model) or page 14 (Fast Sharp  
model)  
Saw runs slow. Saw stalls easily.  
Low power supply voltage  
Extension cord wire size too small. See  
Extension Cords, page 8  
Motorofsawdoesnotrunwhenyousqueeze 1. Switch lockout not pressed in to release 1. Press in switch lockout before squeez-  
trigger.  
trigger  
ing trigger  
2. Extension cord connections loose  
3. Open line fuse or circuit breaker  
4. Bad motor brushes  
2. Check cord connections  
3. Check line fuse or circuit breaker  
4. See authorized service center  
5. See authorized service center  
5. Open wiring circuit on saw  
Motorofsawruns, butchaindoesnotmove. Gear train failure  
See authorized service center  
Chain does not get oil.  
1. Clogged oil slot in guide bar  
2. Oil is too thick  
1. Remove guide bar and clean oil slot  
2. Use correct weight of oil. See Filling Oil  
Tank, page 7  
Chain comes off guide bar.  
1. Chain is loose  
1. Tighten chain. See Saw Chain Tension  
Adjustment, page 7  
2. Guide bar and chain not assembled right 2. See Assembly, page 6  
Saw smokes.  
Saw leaks oil.  
Saw damaged. Do not use saw.  
Oil cap is not secure.  
See authorized service center  
Tighten oil cap. Note: Empty oil tank when  
not in use.  
6. Wipe off outside of saw body. Do this  
with soft cloth dampened with a mild  
soap and water mixture.  
STORAGE  
SERVICE  
PUBLICATIONS  
If storing saw for more than 30 days, follow  
steps below.  
7. Store chain saw  
You can buy a service manual from address  
listedonbackpageofthismanual.Sendacheck  
for $5.00 payable to DESA International.  
• in a high or locked place, out of  
children’s reach  
• in a dry place  
• in a carrying case or with scabbard  
over guide bar  
1. Drain oil tank.  
2. Remove and clean guide bar and chain.  
Clean guide bar and chain by soaking  
in petroleum based solvent or mild soap  
and water mixture.  
You can receive an illustrated parts list free  
of charge. Send a self-addressed stamped  
envelope to address on back page of this  
manual.  
3. Dry guide bar and chain.  
4. Place chain in container filled with oil.  
This will prevent rust.  
TECHNICAL  
SERVICE  
When writing, include model number and  
serial number of saw. You will find these  
numbers on saw motor housing decal.  
5. Wipe a thin coating of oil over surface  
of guide bar.  
You may have further questions about as-  
sembling,operating,ormaintainingthissaw.  
If so, contact DESA International’s Techni-  
cal Service Department at 1-800-323-5190.  
097017  
15  
®
ELECTRIC CHAIN SAW  
PARTS CENTRALS  
Ray's Portable Heater Service  
3191 Myers Road  
Camino, CA 95709  
Portable Heater Parts  
342 North County Road 400 East  
Valparaiso, IN 46383  
219-462-7441  
Four Flags Power Products  
1115 Stateline Road  
Niles, MI 49120  
Forrest Lytle and Sons Inc.  
740 West Galbraith Road  
Cincinnati, OH 45231  
513-521-1464  
Webbs Appliance Center  
1519 Church Street  
Nashville, TN 37203  
615-329-4079  
616-684-2697  
916-644-7716  
1-800-362-6951  
1-800-268-4983  
1-800-899-4079  
Bortz Chain Saw Shop  
Road #2, Box 64A  
Oley, PA 19547  
Baltimore Electronics  
1348 Dixwell Avenue  
Hamden, CT 06514  
203-248-7553  
FBD  
Hance Distributors Inc.  
12795 16th Avenue North  
Plymouth, MN 55441  
612-559-2299  
Industrial Hardware  
4109 Bainbridge Blvd.  
Chesapeake, VA 23324  
757-543-2232  
1349 Adams Street  
Bowling Green, KY 42103-3414  
502-846-1199  
610-987-6452  
1-800-397-7553  
21st Century  
1-800-788-0008  
1-800-654-8534  
Automotive Equipment Service  
3117 Holmes  
Kansas City, MO 64109  
816-531-9144  
2950 Fretz Valley Road  
Perkasie, PA 18944  
215-795-0400  
Eckley’s Small Engine  
31617 Spruce Drive  
Eustis, FL 32726  
Mills Lawn and Garden  
4750 B. Baxter Road, Unit B  
Virginia Beach, VA 23462  
757-490-7001  
Lyons & Lyons Sales Co. Inc.  
Glen Arm Road  
Glen Arm, MD 21057  
301-665-6500  
352-357-6764  
1-800-325-4828  
1-800-843-3546  
Parts Company of America  
1657 Shermer Road  
Northbrook, Ill 60062  
708-498-5900  
LaPortes' Parts & Service  
2444 N 5th Street  
Hartsville, SC 29550  
1-800-333-5966  
Sun Appliance Service Center  
1687 Central Avenue  
Albany, NY 12205  
Tuco Industrial Products  
5223 180th Street SW  
Suite 4A-1  
Lynnwood, WA 98037  
425-743-9533  
Master Parts Distributors  
1184 Wilson NW  
Grand Rapids, MI 49544  
1-616-791-0505  
1-800-446-1446  
803-332-0191  
518-869-9591  
1-800-323-0620  
1-800-735-1268  
AUTHORIZED SERVICE CENTERS  
ALABAMA (AL)  
California Electric Service  
1139 East 12th Street  
Oakland, CA 94606  
510-834-1050  
COLORADO (CO)  
FLORIDA (FL)  
IDAHO (ID)  
A & O General Repair Service  
1470 Opelika Road  
Auburn, AL 36830  
334-821-7022  
McGuckin Power Equipment Center  
2845 Valmont Road  
Boulder, CO 80302  
303-443-9317  
Cricket Shop  
Rossiter Electric  
1501 S. Capitol Ave.  
Idaho Falls, ID 83403  
208-529-3665  
3012 39th Avenue West  
Bradenton, FL 34205  
941-755-7758  
California Electric Service  
2594 East Colorado Blvd.  
Pasadena, CA 91107  
818-792-3194  
Southern Power Tool  
3956 Government Blvd.  
Mobile, AL 36693  
334-666-3623  
Ace Mower and Small Engines  
4718 Chromium Drive  
Colorado Spring, CO 80918  
719-593-0862  
Eckley's Small Engine  
31617 Spruce Drive  
Eustis, FL 32736  
352-357-6764  
Steam Store Rocky Mountain, Inc.  
155 North Gate Mile  
Idaho Falls, ID 83401  
208-522-0609  
California Electric Service  
1717 Bell Street  
Sacramento, CA 95814  
916-443-5711  
ARIZONA (AZ)  
Bartell Tool Service  
1448 W. Cedar Avenue  
Denver, CO 80223  
303-777-5463  
Al's Small Engine, Inc.  
2620 Blanding Blvd.  
Middleburg, FL 32068  
904-282-5416  
Steam Store of Magic Valley, Inc.  
156 4th Avenue South  
Twin Falls, ID 83301  
208-734-3694  
Best Brothers Lawnmower Repair  
5549 W. Glendale Avenue  
Glendale, AZ 85301  
602-939-9170  
California Electric Service  
3430 El Cajon Blvd.  
San Diego, CA 92104  
619-283-6488  
Metrogas Equipment Company  
790 West 64th Ave.  
Denver, CO 80221  
303-428-3036  
S TEK Power Tools  
2605 South Orange Avenue  
Orlando, FL 32806  
407-851-5642  
J & J Enterprises  
D & L Small Engines, Inc.  
10023 North 19th Ave.  
Phoenix, AZ 85021  
602-861-1978  
1704 Addison Avenue East  
Twin Falls, ID 83301  
208-733-2001  
California Electric Service  
1090 Bryant Street  
San Francisco, CA 94103  
415-431-8494  
Winfrey's Repair  
317 8th Street  
Greeley, CO 80631  
970-353-9576  
Lindle & Sons Electric Motor Repair  
7016 Hwy. 22  
Panama City, FL 32401  
850-871-1722  
ILLINOIS (IL)  
Power Tool Service Center  
660 East 19th Street  
Tucson, AZ 85719  
520-884-8974  
Cherry Valley Small Engine Repair  
702 East State Street  
Cherry Valley, IL 61016  
815-332-5636  
California Electric Service  
783 The Alamada  
San Jose, CA 95126  
408-295-0475  
AAA Electric Company, Inc.  
24 South Main Street  
Longmont, CO 80501  
330-776-6031  
Eustis and Sons, Inc.  
7035 66th Street North  
Pinellas Park, FL 34665  
813-544-1486  
CALIFORNIA (CA)  
Ray's Portable Heater Service  
3191 Meyers Road  
Camino, CA 95709  
916-644-7716  
Chainsaw Central  
11 E. Main Street  
Chicago Heights, IL 60411  
708-756-2280  
Lawnmower & Saw  
3115 S. Main Street  
Santa Ana, CA 92707  
714-540-5307  
Dales Electric Motor Repair  
932 Coffman Street  
Longmont, CO 80501  
303-651-6907  
Mulvaney's Inc.  
2148 W. Tennessee Street  
Tallahassee, FL 32304  
904-576-5578  
Lange Electric  
California Electric Service  
1170 G. Burnett Avenue  
Concord, CA 94520  
510-827-1011  
912 E. Fayette  
Effingham, IL 62401  
217-347-7626  
Rincon Valley Yard & Garden  
4972 Sonoma Hwy  
Santa Rosa, CA 95409  
707-593-4124  
CONNECTICUT (CT)  
Baltimore Electronics  
1348 Dixwell Avenue  
Hamden, CT 06514  
203-248-7553  
A-1 Tool Rental, Inc.  
2509 South State Road 7  
West Hollywood, FL 33023  
305-961-9250  
H & R Pump Company, Inc.  
2111 E. Washington Street  
Joliet, IL 60434  
California Electric Service  
612 South Shoppers Lane  
Covina, CA 91723  
California Electric Service  
41715 Enterprise Circle North  
Suite 101  
Temecula, CA 92590  
909-695-5445  
815-726-2950  
818-915-4935  
1-800-397-7553  
GEORGIA (GA)  
Hamilton Hardware  
5300 Veterans Pkwy.  
Columbus, GA 31904  
706-322-6545  
Mathis-Kelley Construction  
1046 W. Jefferson Street  
Morton, IL 61550  
California Electric Company  
1208 East Ash Avenue  
Fullerton, CA 92631  
714-870-0900  
Utility Electric Service  
53 Main Street  
Hartford, CT 06106  
860-246-7271  
309-266-9733  
California Electric Service  
14753 Oxnard Street  
Van Nuys, CA 91411  
818-997-8855  
Cowan Ace Hardware  
1264 Green Street  
Conyers, GA 30207  
770-483-8818  
Ambraw Power Equipment  
310 E. Decatur Street  
Newton, IL 62448  
J & N Garden Equipment  
4460 W. Imperial Hwy.  
Inglewood, CA 90304  
310-671-0079  
Goodies Sales and Service  
133 Hamilton Street  
New Haven, CT 06515  
203-865-1470  
618-783-2821  
California Electric Service  
2314 South Westwood Blvd.  
W. Los Angeles, CA 90064  
310-475-2532  
Douglasville Ace Hardware  
6530 Church Street  
Douglasville, GA 30133  
770-942-7044  
California Electric Company  
11284 Los Alamitos Blvd.  
Los Alamitos, CA 90720  
310-596-7895  
Appliance Servicenter of Stamford  
15 Cedar Heights Road  
Stamford, CT 06905  
PBI  
203-322-7656  
3160 Industrial Drive  
Yuba City, CA 95993  
916-671-1871  
S & P Rental & Supply Co.  
259 Clayton Street  
Lawrenceville, GA 30245  
770-963-0392  
California Electric Service  
23725 Via Fabricante, Unit B  
Mission Viejo, CA 92691  
714-586-9440  
Tifton Electric Motors  
1265 US Hwy. 82E  
Tifton, GA 31794  
912-382-4040  
097017  
16  
OWNER’S MANUAL  
INDIANA (IN)  
KANSAS (KS)  
MARYLAND (MD)  
Fowler's Farm City Sales  
2876 West Washington Road  
Ithaca, MI 48847  
MONTANA (MT)  
Hutchens Sales and Service  
R.R. #5, Box 550  
Bloomfield, IN 47424  
812-876-1891  
Abilene Rent-All & Sales  
1701 West 1st Street  
Abilene, KS 67410  
913-263-7668  
Center Supply Company  
6802 Industrial Drive #208  
Beltsville, MD 20705  
301-595-0860  
Tom's Service Repair  
1111-6th Avenue North  
Billings, MT 59103  
406-259-6179  
517-875-3976  
Superior Industrial Sales & Service  
116 N. State Street  
Jackson, MI 49201  
517-784-0539  
Nichols Ice & Oil  
2018 Park Road  
Connersville, IN 47331  
317-825-3741  
NAAB Electric, Inc.  
2013 W. Jones  
Garden City, KS 67846  
316-276-8101  
Lehmans Hardware, Inc.  
5921 Belair Road  
Baltimore, MD 21206  
410-483-5888  
Mosch Electric Motors, Inc.  
2513 - 17th St. NE  
Black Eagle, MT 59414  
406-453-2481  
Norm's Electric Motor Repair  
414 Walbridge  
Kalamazoo, MI 49001  
616-382-5054  
B & W Repair Service  
213 N. Main Street  
Dale, IN 47523  
Morris Electric Repair  
2423 5th Street  
Great Bend, KS 67530  
316-792-2919  
Norris Taylor Contractors, Inc.  
8480 Ocean Gateway  
Easton, MD 21601  
Sun Rental Center  
1301 - 3rd St. NW  
Great Falls, MT 59404  
406-761-6688  
812-937-2576  
410-822-2050  
A & J Rentals  
Reggie's Small Engine Spec.  
3011 Lower Huntington Road  
Ft. Wayne, IN 46809  
McPherson Rental Center  
911 West First Street  
McPherson, KS 67460  
316-241-3333  
Southern States Frederick Coop  
500 E. South Street  
550 S. 11th Street  
Niles, MI 49120  
616-684-3200  
NEBRASKA (NE)  
Hatten's Electric Service  
130 S. Hastings, Box 843  
Hastings, NE 68901  
402-463-4596  
Frederick, MD 21705  
301-663-6165  
219-747-6212  
Four Flags Power Products  
1115 Stateline Road  
Niles, MI 49120  
Eastside Electric  
928 East Lincoln  
Goshen, IN 46526  
219-533-3823  
Town and Country  
2008 Princeton  
Ottawa, KS 66067  
913-242-3133  
Lyons and Lyons Sales Co., Inc.  
Glen Arm Road  
Lincoln Tool Service Center  
3535 North 40th Street  
Lincoln, NE 68404  
402-464-1157  
Glen Arm, MD 21057  
410-665-6500  
616-684-2697  
Bob's Service Shop  
2537 W. Drahner Road  
Oxford, MI 48371  
810-628-2601  
Mills Electric  
KENTUCKY (KY)  
Hart's Motor Service  
1747 Woodlawn Road  
Bardstown, KY 40004  
502-348-3270  
Chesapeake Rent All  
210 N. Stokes Street  
Havre De Grace, MD 21078  
410-939-1720  
4828 Calumet Ave.  
Hammond, IN 46327  
219-931-3114  
Flohr Electric Motor  
4356 South 90th Street  
Omaha, NE 68127  
402-331-6863  
Don's Small Engine Repair  
630 S. Mill Street  
Plymouth, MI 48170  
313-451-5656  
Tyrie Mower Repair  
110 South 16th Street  
Lafayette, IN 47905  
317-742-7886  
Tracy's Appliance Company  
520 Soleman's Island Road  
P. Frederick, MD 20678  
301-855-1818  
E-Z Rent It Inc.  
MSE Parts Unlimited  
4935 South 136th Street  
Omaha, NE 68137  
402-895-0806  
1428 U.S. 31-W By-Pass  
Bowling Green, KY 42101  
502-782-9462  
Bid's Service, Inc.  
11276 E. Ten Mile  
Warren, MI 48089  
810-759-3040  
Kabelin True Value Hardware  
512 Andrew Avenue  
Laporte, IN 46350  
MASSACHUSETTS (MA)  
Holander Electric, Inc.  
36 Walton Street  
Attleboro, MA 02703  
508-226-1060  
Roman's Repair Shop  
601 College Street  
Bowling Green, KY 42101  
502-746-0857  
Ted's Mower Sales and Service, Inc.  
5155 Q. Street  
Omaha, NE 68117  
402-731-7058  
219-362-7917  
MINNESOTA (MN)  
Patrick's Sales & Service  
415 - 8th Ave. NE  
Brainerd, MN 56401  
218-829-5356  
Krep's Small Engine Repair  
3301 East County Road 350 North  
Muncie, IN 47303  
Hopkinsville Electric Motor  
704 W. 15th Street  
Hopkinsville, KY 42240  
502-886-7585  
Ormond's Inc.  
LaVern Hass Repair  
1204 - 1st Road  
Wisner, NE 68791  
402-529-6846  
115R Dean Ave.  
Franklin, MA 02038  
508-528-2013  
317-282-5139  
Lear Lawn & Garden  
2204 N. Wolfe Street  
Muncie, IN 47303  
317-282-6273  
Perry's Electrical Rebuilders  
24630 Hale Avenue  
Forest Lake, MN 55025  
612-464-8054  
Maury's Fluorescent Appliance  
1521 Bardstown Road  
Louisville, KY 40205  
502-456-1671  
Beacon Lumber/Beacon Rental  
513 Church Street  
NEVADA (NV)  
Fallon Saw & Tool  
300 N. Marine St.  
Fallon, NV 89406  
702-423-1888  
New Bedford, MA 02745  
508-995-1766  
Li'l Engine Sales & Service, Inc.  
1428 Vincennes Street  
New Albany, IN 47150  
812-944-1377  
Hance Distributor, Inc.  
12795 16th Avenue North  
Plymouth, MN 55441  
612-559-2299  
Rental World, Inc.  
9509 Dixie Hwy.  
Louisville, KY 40272  
502-935-8853  
Grafton Power Equipment  
North Grafton Shopping Center  
9 Williams Road  
North Grafton, MA 01536  
508-839-6366  
One Stop Shop  
1408 Industrial Way #3  
Gardnerville, NV 89410  
702-782-7004  
Ertel & Sons Portable Welding  
109 E. Main Street  
Swayzee, IN 46986  
317-922-4611  
Hance Sales and Service  
11212 Wayzata Blvd.  
Minnetonka, MN 52343  
612-545-8467  
All States Industrial Repair  
728 E. Center Street  
Madisonville, KY 42431  
502-821-6555  
Mott's Tool Repair Service  
92 Rayber Road  
Orleans, MA 02653  
508-240-0764  
NEW HAMPSHIRE (NH)  
Taylor Rental Center  
223 Wincherster Street  
Keene, NH 03431  
603-352-0539  
Portable Heater Parts  
342 North County Road, 400 East  
Valparaiso, IN 46383  
219-462-7441  
Andy's Small Engine Repair  
209 9th Avenue, NE  
Rochester, MN 55906  
507-280-0373  
Bluegrass Plumbing and Heating  
121 South First Street  
Richmond, KY 40475  
606-623-2390  
Utility Electric Service #2  
810 Main Street  
Springfield, MA 01105  
413-781-1635  
Kingston Enterprises  
85 North Road  
Kingston, NH 03848  
603-642-3506  
D W Handy's  
Reed's Sales & Service  
1260 Payne Ave.  
St. Paul, MN 55101  
612-774-9515  
2112 S. 15th Street  
Vincennes, IN 47591  
812-886-0172  
LOUISIANA (LA)  
Welch Sales & Service  
13348 W. Main  
La Rose, LA 70373  
504-693-3351  
Franconia Fuel Company, Inc.  
379 Main Street  
Wareham, MA 02571  
508-295-0039  
Hammar Industrial Supply  
175 Amherst Street  
Nashua, NH 03061  
603-822-5161  
IOWA (IA)  
Brown's  
408 South Fifth Street  
Abel, IA 50003  
515-993-3053  
MISSISSIPPI (MS)  
Handy Man Rentals  
1904 Shiloh Road  
Corinth, MS 38834  
601-287-2460  
Triangle Bicycle and Lawnmower  
5433 Crowder Road  
New Orleans, LA 70127  
504-241-3239  
MICHIGAN (MI)  
R & A Service  
12900 Haggerty Road  
Belleville, MI 48111  
313-697-1144  
Exeter Rent All  
State Rt 27, Box 68A  
Raymond, NH 03077  
603-895-6583  
Beal's Motor Rewinding  
600 West Beach  
Cherokee, IA 51012  
712-225-6173  
MISSOURI (MO)  
MAINE (ME)  
Stewarts Enterprises  
7631 NW Salebarn Road  
Cameron, MO 64429  
816-632-6578  
Richard's Electric Motor  
259 Main Street  
Caribou, ME 04736  
207-498-8950  
Thompson's Rental Resale Repair  
11973 New Lothrop Road  
Byron, MI 48418  
Blink Electric Motors  
Rear 116 N. 1st Ave.  
Marshalltown, IA 50158  
515-752-3036  
810-266-4969  
Northwest Power Sales  
RD #2, Box 200  
Maryville, MO 64468  
816-582-5080  
Roger's Electric Motor Shop  
823-West Main Street  
Madawaska, ME 04756  
207-728-4253  
Renter Center, Inc.  
24948 Gratiot  
East Pointe, MI 48021  
810-772-8111  
Fry Company  
Box 96 Thatcher Ave.  
Millerton, IA 50165  
515-897-3235  
Buchheit, Inc.  
Rent-N-Save  
Master Service Center  
7876 Division  
Grand Rapids, MI 49504  
616-455-3117  
Route 7, Box 239  
Perryville, MO 63775  
573-547-1010  
28 Allen Avenue  
Portland, ME 04103  
207-797-2223  
Moreland Repair  
2145 Jericho Road  
Peosta, IA 52068  
319-583-3669  
L.A. Pickard Sales & Service  
383 Lewiston Road  
Topsham, ME 04086  
207-725-2874  
Wolf Creek Farm Supply  
8011 Wolf Creek Road  
Herron, MI 49744  
Northeast Iowa Motor Service  
24665-150th Street  
Sumner, IA 50674  
517-727-2391  
Chicago Drive Rentals, Inc.  
11298 Chicago Drive  
Holland, MI 49424  
616-396-9575  
319-578-5883  
Black Hawk Rental  
324 West 15th Street  
Waterloo, IA 50702  
319-234-4421  
097017  
17  
®
ELECTRIC CHAIN SAW  
NEW JERSEY (NJ)  
Complete Saw Service  
336 River Road  
Advanced Power Equipment  
101 Fairgrounds Drive  
Manlius, NY 13104  
315-682-4010  
North East Mower Service  
412 East 156th Street  
Cleveland, OH 44110  
216-531-8197  
OREGON (OR)  
SOUTH CAROLINA (SC)  
Hall's Small Motor Repair  
225 Heathwood Drive  
Aiken, SC 29803  
Turner’s Lawnmower and Saw  
728 SE Robin Way  
Gresham, OR 97080  
503-665-5441  
Garfield, NJ 07026  
201-478-7838  
803-649-6313  
P & C  
Pecnik's Lawnmower Service  
732 East 163rd Street  
Cleveland, OH 44110  
216-531-8480  
Nemeth's Mower Service  
55 - 4th Ave.  
Haskell, NJ 07420  
201-835-0080  
12 East Street  
Nunda, NY 14517  
716-468-5050  
Pendleton Grain Growers  
200 S. 1st Street  
P.O. Box 1248  
Hermiston, OR 97801  
541-567-5591  
Todd's Electric Motor Repair  
110 Laurel Street  
Conway, SC 29526  
803-248-2444  
Otega Repair  
Lefeld Welding & Steel Supply  
512 N. Second Street  
Coldwater, OH 45828  
419-678-2397  
Air & Electric Tool Service, Inc.  
215 North 8th Street  
Kenilworth, NJ 07033  
908-272-5567  
Rd #2, Ostdawa Ave.  
Otego, NY 13825  
607-988-7859  
LaPortes Parts & Service  
2444 N. 5th Street  
Hartsville, SC 29550  
803-332-0191  
Mattix Appliance Parts Company  
501 N. Main  
Phoenix, OR 97535  
541-535-6263  
Owego Agway Coop  
38 West Avenue  
Owego, NY 13827  
607-687-2039  
Dayton Hardware & Supply  
16-32 N. Irwin Street  
Dayton, OH 45404  
Associated Industries  
Rd 38, Box 2486  
Mt. Holley, NJ 08060  
609-267-8417  
Turner Repair Service  
3 E. Belvue Road  
Taylors, SC 29687  
864-244-1746  
Oregon Appliance  
2137 East Burnside Street  
Portland, OR 97214  
503-235-6681  
513-258-3721  
1-800-762-3426 Ohio only  
Jack-n-Heater Service  
185 Beartown Road  
Painted Post, NY 14870  
607-962-1239  
Woodchuck's Lawnmower  
and Appliance  
220 Whitehorse Pike  
Magnolia, NJ 08049  
609-783-1111  
Ken's Repair  
TENNESSEE (TN)  
3246 S. Sectionline  
Delaware, OH 43015  
614-369-4798  
PENNSYLVANIA (PA)  
Albright's Hardware  
2119 Wabert Ave.  
Allentown, PA 18104  
610-433-3831  
Cole's Small Equipment Center  
247-A Vance Tank Road  
Bristol, TN 37620  
Larmon Small Engine  
16353 Co. Rt. 91  
Pierrepont Manor, NY 13674  
315-465-6671  
615-968-1175  
Lavon Dietsch Repair  
07145 Scott Rd. Rt #2  
Edgerton, OH 43517  
419-298-2948  
Myron Tepper/Tep's Power  
Equipment  
1007 N. High Street  
Millville, NJ 08332  
609-825-8294  
Vista Small Engine  
1510 Vista Lane  
Clarksville, TN 37043  
615-552-6953  
General Rental & Sales Center  
Old Rt 1 & 41  
Avondale, PA 19311  
610-268-2825  
R & D Mower & Snowblower  
Sales and Service  
1630 Empire Blvd.  
Webster, NY 14580  
716-671-9409  
Anytool & Outdoor Power Equip.  
21150 Lorain Road  
Fairview Park, OH 44126  
216-356-1920  
Master Repair Service  
305 Elmore Road  
Crossville, TN 38555  
615-484-2061  
Capitol Service & Equipment  
551 New Market Road  
Piscataway, NJ 08855  
908-968-5577  
Bud's Tractor and Mower Sevice  
21 Bock Lane  
Baden, PA 15005  
412-869-7142  
Bedford Appliance, Inc.  
1173 Yonkers Ave.  
Yonkers, NY 10704  
914-237-7575  
LaGrange True Value  
300 E. Main Street  
LaGrange, OH 44050  
216-355-4222  
The Speciality Shop  
2300 East Magnolia Avenue  
Knoxville, TN 37917  
423-523-6894  
Handyman's Tool Shop  
508 State Hwy. #10  
Randolph, NJ 07869  
201-361-1581  
Copper Creek  
Rd. #1, Locust Valley  
Barnesville, PA 18214  
717-467-2792  
NORTH CAROLINA (NC)  
Ray's Lawn Mower & Machine  
1414 Landis Avenue  
Charlotte, NC 28205  
704-377-1112  
Deep Run Mower Service  
58781 Heil Addn. Deep Run  
Martins Ferry, OH 43935  
614-859-6131  
Authorized Equipment Service  
812 Polk Avenue  
Memphis, TN 38126  
901-774-0850  
Sam's Repair Shop  
137 W. Bennett Ave.  
Wildwood, NJ 03077  
603-895-6583  
Passmore Service Center  
1108 Rt. 100  
Betchelsville, PA 19505  
610-367-9084  
Worcester Sales and Service  
34200 Lorian Road  
N. Ridgeville, OH 44039  
216-327-2196  
Martin Equipment Company  
4209-B US 70 E.  
Goldsboro, NC 27534  
919-778-5996  
Webb's Appliance Service Center  
1519 Church Street  
Nashville, TN 37203  
615-329-4079  
NEW MEXICO (NM)  
K & S Service Center  
7521 Menaul N.E.  
Albuquerque, NM 87110  
505-884-6262  
Engine Doctors  
20 Russell Blvd.  
Bradford, PA 16701  
814-362-3091  
Staker Sales & Service  
1424 Ninth Street  
Portsmouth, OH 45662  
614-353-6965  
Hickory Home & Garden Center  
336 HWY 321 NW  
Hickory, NC 28601  
704-327-3719  
TEXAS (TX)  
Pro-Fix  
Industrial Distributing Co.  
9411 Neils Thompson Dr.  
Austin, TX 78759  
512-837-4122  
NEW YORK (NY)  
Rear 681 Main Street  
Edwardsville, PA 18704  
717-288-0476  
Sun Appliance Service Center  
1687 Central Avenue  
Albany, NY 12205  
518-869-9591  
Leonard Hardware  
145 North 15th Street  
Sebring, OH 44672  
330-938-6329  
Bowden Electric Motor Service  
1681 S. Wesleyan Blvd.  
Rocky Mount, NC 27803  
919-446-4203  
Carson's Hardware  
637-43 Main Street  
Hellertown, PA 18055  
610-838-7741  
Bud's LP Gas & Supply  
225 Grand  
Channelview, TX 77330  
713-457-2456  
Valley Mower Service  
2857 Ellis Creek Road  
Barton, NY 13734  
607-589-4825  
Sparks Sales & Service  
5184 Fletcher Chapel Road  
Springfield, OH 45502  
513-323-5925  
Small Engine Performance Ctr.  
312 Eldred  
Valdese, NC 28690  
704-879-9652  
Eaton Enterprises  
240 Main Street  
Imperial, PA 15126  
412-695-0702  
Corpus Christi Power Tool & Rpr.  
3701 Agnes  
Corpus Christi, TX 78405  
512-883-1117  
White Tool Supply Inc.  
3047 Atlantic Avenue  
Brooklyn, NY 11208  
718-227-8844  
Eckert Bros.  
NORTH DAKOTA (ND)  
Fix-It Shop  
316 - 21st St. East  
Dickinson, ND 58601  
701-225-0766  
244 Factory Street  
Sugarcreek, OH 44681  
216-852-2611  
Valray Nurseries Inc.  
R.D. #8, Box 362  
Kittanning, PA 16201  
412-548-1579  
Freel Enterprise  
118 Elston  
Dallas, TX 75232  
214-376-9913  
Shields Brothers of Buffalo  
1410 Main Street  
Buffalo, NY 14209  
716-883-3860  
Larry's Mini Engines  
4732 US Route 20 West  
Wakeman, OH 44889  
216-839-2508  
Ted's Saw Service  
412 South 4th Street  
Grand Forks, ND 58201  
701-775-7343  
Petrosky's Hardware & Supply Co.  
602 Alexandria Street  
Latrobe, PA 15650  
Hawn Equipment Rental  
7777 Hawn Freeway  
Dallas, TX 75217  
214-398-8121  
Lehman's Farm & Home Supply  
Route 26  
Denmark, NY 13631  
315-493-1151  
OKLAHOMA (OK)  
B.M.I. Inc.  
13102 East 1st Street  
Broken Arrow, OK 74012  
918-252-0011  
412-537-3541  
Craig's Small Engine Repair  
508 East 2nd Street  
Williston, ND 58801  
701-774-0798  
Reddi-Rentals  
Dyer Cycle  
948 S. Woodbourne Rd.  
Levittown, PA 19057  
215-943-4800  
4501 Dyer Street  
El Paso, TX 79930  
915-566-6022  
John’s Engine Repair  
10482 Sisson Hwy.  
Eden, NY 14057  
716-337-3719  
H. L. Moss  
OHIO (OH)  
1714 E. 15th Street  
Tulsa, OK 74104  
918-744-1305  
Raymond, M. Nolt  
290 S. Shirk Road  
New Holland, PA 17557  
717-354-0198  
Ray DeSpain's Inc.  
Carter Electrical Repair  
3448 Lunar Rd. NE  
Carrollton, OH 44615  
330-627-4061  
P.O. Box 184, Loop 494 North  
New Caney, TX 77357  
713-689-2121  
M & S Repair Shop  
303 Hilltop Drive  
Elma, NY 14059  
716-652-0311  
Kay Electric Motors Inc.  
810 48th Street  
Woodward, OK 73801  
405-256-3254  
Service Department  
Bortz Chainsaw Shop  
45 Bortz Road  
Oley, PA 19547  
610-987-6452  
Northwest Mower Sales and Service  
6086 Cheviot Road  
Cincinnati, OH 45247  
513-385-2400  
Crossbay Appliance Service  
158-34 Crossbay Blvd.  
Howard Beach, NY 11414  
718-843-4422  
Snyder Electric Company  
1500 Chateau Street  
Pittsburgh, PA 15233  
412-231-3100  
Forrest Lytle & Sons  
740 W. Galbraith Road  
Cincinnati, OH 45231  
513-521-1464  
Belco Equipment Company  
3801 - 29th Street  
Long Island City, NY 11101  
718-361-1122  
Stamm's Mower Repair  
Rd. 5, Pine Lane Box 150  
Selinsgrove, PA 17870  
717-743-7651  
Anytool Precision Sharpening Repair  
21150 Lorain Road  
Cleveland, OH 44126  
216-356-1920  
Para-Deys Tools  
708 Victor Road  
Macedon, NY 14502  
315-986-2520  
097017  
18  
OWNER’S MANUAL  
UTAH (UT)  
VIRGINIA (VA)  
WASHINGTON (WA)  
Action Small Appliance Service  
1500 145th Place SE  
Bellevue, WA 98005  
206-455-3578  
WEST VIRGINIA (WV)  
Beckley Mower Service  
3695 Robert C. Byrd Drive  
Beckley, WV 25802  
304-253-5748  
Roosevelt Service Center  
133 South 300 East, Box 1546  
Roosevelt, UT 84066  
801-722-2708  
Industrial Hardware  
4109 Bainbridge Blvd.  
Chesapeake, VA 23324  
804-543-2232  
Longs Engine Service  
7536 Stone Road  
Salt Lake, UT 84121  
801-943-5135  
Warren E. Smith Shops  
564 Reading Rd. Ext.  
300 Madestic Drive  
Christiansburg, VA 24073  
540-382-5501  
TUCO Industrial Products  
5227 180th SW, Suite 4A-1  
Lynnwood, WA 98046  
206-743-9533  
Town and Country Supply  
4117 First Avenue  
Nitro, WV 25143  
304-755-3520  
Appliance Service Center  
210 E. 600 South  
Salt Lake City, UT 84111  
801-328-9703  
Action Small Appliance  
2125 Second Avenue  
Seattle, WA 98121  
206-448-2020  
WISCONSIN (WI)  
Smith Petroleum Ltd.  
217 N. Walworth  
Darien, WI 53314  
414-724-3206  
Mills Repair Service  
4750 B. Baxter Road, Unit B  
Virginia Beach, VA 23462  
757-490-7001  
VERMONT (VT)  
Brown and Roberts  
182 Main Street  
Brattleboro, VT 05301  
802-257-4566  
A to Z Rentals  
American Power Equip. Ctr.  
6502 Horsepen Road  
Richmond, VA 23230  
804-285-4838  
10903 E. Sprague  
Spokane, WA 99206  
509-924-2000  
Ken's Economy Sales  
8887 Highway A  
Marshfield, WI 54449  
715-676-2143  
Lifficks Electric Shop  
8239 S. Park Avenue  
Tacoma, WA 98408  
206-474-7403  
Stafford Equipment Sales & Service  
21055 Jefferson Davis Hwy.  
Stafford, VA 22554  
Moore's Repair Service  
W287 & N2108 Stuart Drive  
Pewaukee, WI 53072  
414-691-2814  
540-720-1710  
Outdoor Power Equipment  
800 White Marsh Road  
Suffolk, VA 23434  
804-925-4933  
Morisse Power Center  
200 N. Chicago Avenue  
S. Milwaukee, WI 53172  
414-762-6444  
Purchase these accessories and parts from  
your nearest dealer or service center. If they  
can not supply these accessories or parts,  
either contact your nearest Parts Central or  
DESA International for referral informa-  
tion. Parts centrals are listed in this manual.  
REPLACEMENT  
PARTS AND  
ACCESSORIES  
WARNING: Use only replace-  
ment parts and accessories de-  
scribed in this manual. Use of  
other parts or accessories could  
damage saw or injure operator.  
DESA International  
P.O. Box 90004  
Bowling Green, KY 42102-9004  
1-800-972-7879  
Parts Department  
LNT-2  
Part Number Description  
EL-1/EL-7 Fast Sharp  
Part Number Description  
EL-7 - 100015  
Part Number Description  
097566-01S  
Guide bar, 8"  
091369S  
097567-01S  
091371S  
Chain, 8"  
Guide bar, 10"  
Chain, 10"  
097570-01S  
091367S*  
076695  
Guide bar, 14"  
Chain, 14"  
Drive sprocket  
101623-01  
101619-01  
075752  
Guide bar, 15"  
Chain, 15"  
Drive sprocket  
097568-02S  
Guide bar, 12"  
091373S  
Chain, 12"  
EL-7, 098031J, 099039J, 100089-01, General  
075752  
Drive sprocket  
100089-04, 100089-05  
Part Number Description  
Part Number Description  
079963-02  
Plasticscabbard,8"&10"  
099178H, 100089-06, 100089-07 & 097572-03S  
Guide bar, 16"  
Chain, 16"  
Drive sprocket  
079963-04  
Plastic scabbard,  
12", 14", & 16"  
Hand Guard  
EL-1  
091375S  
075752  
Part Number Description  
079088-01  
077155  
097570-01S  
091374S  
075752  
Guide bar, 14"  
Chain, 14"  
Drive sprocket  
Adjusting Plate Assy.  
POLE SAW, 104316-01  
POLE SAW ASSEMBLY, 104317  
Part Number Description  
* Includes automatic chain sharpener.  
104302-01S  
104301S  
075752  
Guidebar, 8"  
Chain, 8"  
Drive Sprocket  
097017  
19  
Warranty Service  
Non-Warranty Service  
REPAIR SERVICE  
If saw requires warranty service, return it to If saw requires service, return it to nearest  
nearest authorized service center. You must authorized service center. Repairs will be  
show proof of purchase. If faulty materials billed to you at regular repair list prices.  
or workmanship caused damage, we will Note:Normalwear, misuse, abuse, neglect,  
Note: Only use original replacement parts.  
Thiswillprotectyourwarrantycoveragefor  
parts replaced under warranty.  
Each authorized service center is indepen-  
dently owned and operated. For additional  
service center or warranty information, call  
1-800-323-5190.  
repair or replace saw without charge.  
or accidental damage is not covered under  
warranty.  
Model ______________  
Serial No. ______________  
Date Purchased ______________  
ELECTRIC CHAIN SAW LIMITED WARRANTY  
Always specify model and serial numbers when writing the factory.  
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written warranty. We  
make no other warranty, expressed or implied.  
DESA International warrants this electric chain saw and any parts thereof, to be free from defects in material and workmanship for one year from  
the date of first purchase from an authorized dealer, provided that the product has been properly maintained and operated in accordance with all  
applicable instructions. The bill of sales or proof of purchase must be presented at the time a claim is made under this warranty.  
This warranty is extended only to the original retail purchaser. This warranty covers only the parts and labor required to restore this chain saw  
to its proper operating condition. Warranty parts must be obtained through factory authorized dealers and service centers for this product. These  
dealers and service centers will provide original factory replacement parts. Failure to use original factory replacement parts voids this warranty.  
This warranty does not cover commercial, industrial, or rental usage, nor does it apply to parts that are not in original condition because of normal  
wear and tear, or parts that fail or become damaged as a result of misuse, accident, lack of proper maintenance, tampering, or alteration. Travel,  
handling, transportation, and incidental costs associated with warranty repairs are not reimbursable under this warranty and are the responsibility  
of the owner.  
To the full extent allowed by the law of the jurisdiction that governs the sale of the product, this express warranty excludes any and all other  
expressed warranties and limits the duration of any and all implied warranties, including warranties of merchantability and fitness for a particular  
purpose to one year form the date of first purchase, and DESA International’s liability is hereby limited to the purchase price of the product and  
DESA International shall not be liable for any other damages whatsoever including indirect, incidental, or consequential damages.  
Some states do not allow limitation of how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages,  
so the above limitation of damages may not apply to you.  
Thiswarrantyprovidestheoriginalpurchaserwithspecificrights. Forinformationregardingthoserights, pleaseconsulttheapplicablestatelaws.  
INTERNATIONAL  
2701 Industrial Drive  
P.O. Box 90004  
Bowling Green, KY 42102-9004  
097017 01  
097017-01  
REV. X  
5/98  
NOT A UPC  

Pioneer Car Amplifier SA 500 User Manual
Philips SHB6100 User Manual
Panasonic PV7667 User Manual
Panasonic DMP BD80GN User Manual
Oster Blender OSTER VERSA PERFORMANCE BLENDER User Manual
Magnadyne M3 LCD User Manual
Mackie Car Speaker SRM450V2 User Manual
KitchenAid 4KFP720BU0 User Manual
Kenwood KVT 522DVDY User Manual
Kenwood KFC 1383 User Manual