Radio Shack PLDVD188 User Manual

SPECIFFICATION  
PLDVD188  
INSTRUCTION MANUAL  
GENERAL SPECIFICATIONS  
Power Requirement...............................14.4V DC(10.8 to 15.6 allow)  
Current Consumption.................................................Less than 2.0A  
Maximun Power output....................................................240WATTS  
Line output....................................................RMS 35W x 4 @ 4 ohm  
Dimensions(w x h x d)............................................182 x 53 x 158mm  
DVD DECK SPECIFICATIONS  
Format...........................................DVD-Video Disc (2 Layer, 2 side)  
Compact Disc  
Video System...................................................Standard NTSC/PAL  
Audio System..........................................................................MP3  
Loading System......................................................... Auto Loading  
Mounting Angle................................................................0 to +/-30  
OPEN  
IR  
TITLE  
CHP TRK  
RDM LOUD DTS  
DIGITAL  
CH  
+
VIDEO  
COMPACT  
SEL  
LOC  
BND  
MU  
CLAS  
POP  
DIGITAL AUDIO  
COMPACT  
ST LOC INT RPT PRG  
-
ROCK  
VIDEO  
DOLBY  
DIGITAL VIDEO  
D
I
G
I
T
A
L
DVD/SVCD/VCD/CD/MP3 PLAYER  
APS  
1TOP  
2RPT  
3INT  
4RDM  
5
6
CLK  
DSP  
MD  
VIDEO SPECIFICATIONS  
Video System..................................4:3 Letter Box and 4:3 Pan Scan  
Video Output level.................................................1.0Vp-p 75 ohms  
Horizontal Resolution................................................................500  
Video Input Terminal......................................0.5 to 2.0Vp-p 75 ohms  
POWER  
SEL  
MODE  
+
VOL+  
UP  
F.FWD  
/NEXT  
ENTER  
DN  
F.BWD  
/PREV.  
VOL-  
AUDIO SPECIFICATIONS  
Fully Compatible To All Types  
Of Discs Such As DVD, VCD,  
SUPER VCD, MP3, CD.  
STOP  
PLAY  
PAUSE  
MENU  
BAND  
Maximum Output.......................................................2Vrms(+/-3dB)  
Frequency Response....................................................20 to 20KHz  
S/N Ratio(A-vtd)......................................................................85dB  
Separation..............................................................................80dB  
1
2
6
9
3
7
0
4
8
5
REPEAT  
+10  
SUBTITLE  
LOC  
ANGLE  
MUTE  
OSD  
RADIO SPECIFICATIONS  
FM SECTION  
AUDIO  
ST  
TITLE/PBC  
A/P  
DSP  
CLK  
Frequency range.................................................87.5MHz - 107.9MHz  
Usable sensitivity......................................................................3uV  
I.F Frequency.....................................................................10.7MHz  
AM SECTION  
ANTI-THEFT FLIP DOWN DETACHABLE PANEL  
CAR DVD VIDEO DIGITAL PLAYER  
Frequency...........................................................530KHz - 1710KHz  
AM/FM-STEREO DIGITAL PLL TUNING RADIO  
WITH INFRARED REMOTE CONTROLLER  
4 x 35W  
29  
2
CONTENTS  
ABOUT FRONT PANEL AND PROTECTION CASE  
WARNING................................................................................................. 1  
REGION MANAGEMENT INFORMATION.....................................................1  
CONTENTS...............................................................................................2  
DVD FEATURES........................................................................................3  
THE FRONT PANEL DIAGRAM...................................................................4  
DESCRIPTION OF THE FRONT FACE AFTER TAKINGOUT THE FRONT PANEL...........................4  
DESCRIPTION OF THE REAR CONNECTORS............................................5  
THE REMOTE CONTROLLER DIAGRAM.....................................................6  
DESCRIPTION OF LCD ON THE FRONT PANEL..........................................7  
DESCRIPTION OF THE BACK OF THE FRONT PANEL.................................8  
LOADING THE BATTERY IN THE REMOTE CONTROLLER...........................8  
CONNECTING..........................................................................................9  
GLOSSARY.............................................................................................10  
CAUTION: Do not install the detachable panel before connecting the wire.  
1. The unit is designed for negative terminal of the battery which is connected to the  
vehicle metal. Please confirm it before installation.  
2. If the car interior is extremely hot, as after being parked in the sun, do not use  
the player until the car has been driven for a while to cool off the interior.  
3. Press the OPEN button to flip down the front panel (see fig.1), then take away the  
front panel (see fig.2) and put it in the protective case (see fig.3) safe keeping.  
SAME FUNCTTION BBUUTTONSS IN DIISC ORR RRADIO MMODE.11  
4. Install the front panel back into its bracket and then push it back to the position for  
playing (see fig.4).  
RADIO OPERATION......................................................................12  
FRONT PANEL  
FRONT PANEL  
DISC BASIC OOPERRAATION  
TO TURN ON TO PLAY.............................................................................13  
TO PAUSE THE PLAYBACK......................................................................14  
TO STOP THE PLAYBACK........................................................................14  
TO END PLAYING....................................................................................15  
DISC ADVVANCEEDD OPERAATION  
TO SELECT PLAYING CONTENTS WITH THE MENU.................................16  
FAST FORWARD OR REVERSE PLAYING.................................................16  
TO SELECT NEXT OR LAST CHAPTER/TRACK TO PLAY............................17  
TO REPEAT PLAYING..............................................................................17  
TO CHANGE THE LANGUAGE OF THE CAPTION......................................18  
TO CHECK TITLE, CHAPTER SEQUENCE NUMBER AND PLAYING TIME...18  
USE OF PAD NUMBERS...........................................................................19  
VIEW IN DIFFERENT ANGLE....................................................................19  
TO SELECT THE FIRST TRACK/CHAPTER TO PLAY..................................20  
TO SCAN DISC........................................................................................20  
TO PLAY DISC IN RANDOM .....................................................................20  
CHANGING LANGUAGE TYPE.................................................................20  
RESET DISTORTED PROGRAM...............................................................21  
SETTING UP SYSTEM.............................................................................21  
OPEN BUTTON  
( FIG.1)  
( FIG.2)  
PROTECTIVE CASE  
INSTALLATION........................................................................................25  
CARE AND MAINTENANCE......................................................................27  
ABOUT FRONT PANEL AND PROTECTION CASE......................................29  
TROUBLE SHOOTING..............................................................................30  
SPECIFICATION............................................................................COVER 4  
FRONT PANEL  
( FIG.3)  
FRONT PANEL  
( FIG.4)  
28  
3
CLEANING DISCS  
DVD FEATURES  
Before playing, clean the disc with a clean, lint-free.  
Flip the disc in the direction of the arrow.  
MAIN FUNCTIONS  
* Fully compatibility/ Its fully compatible to all types of discs  
such as DVD, SVCD, VCD, CD, Mp3.  
NOTE:  
. Do not use so solvents such as benzine, thinners. Commercially available  
cleaners or anti static spray damage the unit.  
* Picture with high fidelity resolution/ Horizontal resolution  
as high as 500dpi. It can make full use of the advantages  
of large screen TV based on the fidelity of normal TV.  
Insert a disc with the label surface down. Doing so may damage the unit.  
Label  
surface up  
OTHER FUNCTIONS  
NOTE:  
. Do not try to insert another disc when one has been already inserted.  
Doing so may damage the unit.  
.Handle the disc by its edge. And to keep the disc clean, do not touch  
the surface.  
* Many angles of enjoyment/Users can enjoy the picture from  
different angles selected such as zoom in, side view,  
panorama etc.  
* Many types of picture ratio modes/ These modes enable  
the DVD player to suit different TV screen.  
.Do not stick paper or tape on the disc.  
.Do not expose the disc to direct sunlight or heat sources such as hot air  
ducts. Or leave it in a car parked in direct sunlight where there can be a  
considerable rise in temperature.  
27  
4
THE FRONT PANEL DIAGRAM  
CARE AND MAINTENANCE  
4
9
2
1
3
12  
DVD CARE  
* Always handle the disc by the edges. Never touch the surface. To  
remove fingerprints and dust, use a soft cloth and wipe in a straight  
line from the center of the disc to the outside edge.(See page 28)  
* Take care of IR Remote Control. Keep the remote with your DVD  
cases, where it is unlikely to be lost or damaged.  
* Keep liquids away from the DVD player, including beverages and  
cleaning liquids. Spilling any liquid on the player can damage the  
electronics, resulting in an electrical shock or fire.  
OPEN  
IR  
TITLE  
CHP TRK  
RDM LOUD DTS  
DIGITAL  
CH  
+
VIDEO  
COMPACT  
SEL  
LOC  
BND  
MU  
CLAS  
POP  
DIGITAL AUDIO  
COMPACT  
ST LOC INT RPT PRG  
-
VIDEO  
ROCK  
DOLBY  
DIGITAL VIDEO  
D
I
G
I
T
A
L
DVD/SVCD/VCD/CD/MP3 PLAYER  
APS  
1TOP  
2RPT  
3INT  
4RDM  
5
6
CLK  
DSP  
MD  
* If the unit or remote control should become wet, turn off all power  
and let an authorized dealer clean or service the equipment.  
CAUTION:  
DO NOT ATTEMPT TO OPEN OR SERVICE THE UNIT OR REMOTE  
CONTROL. THE INTERNAL PARTS ARE NOT USER SERVICEABLE.  
* Do not use any liquid or aerosol cleaners, anti-static spray, or  
thinner to clean the disc surface.  
10 11  
6
5
14  
15  
8
13  
7
9. LOCAL/DISTANCE BUTTON  
1. OPEN BUTTON  
2. LCD SCREEN  
10. APS BUTTON  
* Do not allow coins, cleaning cloths, papers and other objects to be  
pushed into the DVD slot, these objects could connect with a voltage  
point inside the unit and cause an electrical shock, or may short out  
pacts causing unit failure or fire.  
11. CLOCK BUTTON  
3. IR REMOTE SENSOR  
4. BAND BUTTON  
12. MUTE/LCD COLOUR BUTTON  
13. PRESET STATION AND TOP/RPT  
/INT/RDM BUTTONS  
5. UP(^)/DN(V) BUTTONS  
6. PLAY/PAUSE BUTTON  
7. MODE BUTTON  
TEMPERATURE AND MOISTURE  
when the inside of the vehicle is very cold and the player is used  
immediately, moisture may form on the disc or the optical parts and  
proper playback may not be possible. If moisture forms on the disc,  
wipe it off with a soft cloth. If moisture forms on the optical parts of  
the player, allow the player to sit for about one hour with power on.  
The condensation will disappear naturally allowing for normal operation.  
Please consult your nearest dealer for recommendations and service.  
14. POWER BUTTON  
15. SOUND MODE AND LEVEL BUTTONS  
8. DISPLAY/SUBWOOFER BUTTON  
DESCRIPTION OF THE FRONT FACE AFTER TAKING OUT THE FRONT PANEL  
OPERATION PRECAUTIONS  
* Do not subject the unit to direct sunlight or in extremely hot  
environment (e.g closed windows on a hot summer day, direct,  
direct path or heater vent, etc.).  
RESET  
* Avoid using the unit under the following conditions:  
- After external parking on an extremely hot or cold day.  
- Near strong magnetic fields.  
- In an environment with excessive humidity, dust, or vibration(e.g  
off-road travel, etc.)  
* Do not directly touch the disc surface. Never stick labels on the  
surface of the disc or mark the surface with a pen.  
* Always place a DVD disc back into its case after use.  
1
2
1.LED INDICATOR: Flashing when detachable panel is removed.  
2.RESET BUTTON: Press it to rehabilitate the distorted program  
to zero.  
26  
5
INSTALLLATION  
DESCRIPPTION OF THHE REAR COONNNECTORS  
1
Firstly install the left side, then push  
the right side to make it combine  
with the unit chassis.  
4
2
3
1,2. VIDEO OUTPUT (2 RCA jacks)  
Use an video cable to connect the video output signal to the external  
video monitors.  
3. OPTICAL DIGITAL AUDIO OUTPUT  
Use an optical audio cable to connect the digital audio output signal  
to external audio amplifier system.  
4. WIRING CONNECTING SOCKET  
25  
6
THE REMOTE CONTROLLER DIAGRAM  
INSTALLATION  
2
1
3
POWER  
MODE  
SEL  
4
5
25  
24  
23  
DASH BOARD  
1. MODE BUTTON  
+
VOL+  
UP  
ENTER  
DN  
F.FWD  
/NEXT  
2. SEL BUTTON  
6
METAL MOUNTING STRAP  
F.BWD  
/PREV.  
VOL-  
7
HEX NUT  
3. POWER BUTTON  
22  
21  
SPRING WASHER  
8
STOP  
PLAY  
PAUSE  
MENU  
BAND  
CONSOLE  
PLAIN WASHER  
PLAIN WASHER  
4. JOG UP/SEEK UP BUTTON  
5. F.FWD/NEXT BUTTON  
6. JOG RIGHT BUTTON  
7. F.BWD/PREV. BUTTON  
8. JOG DN/SEEK DN BUTTON  
9. MENU/BAND BUTTON  
9
SLIDE BRACKET HOUSING  
TAPPING SCREW  
1
2
6
9
3
7
4
8
10  
11  
5
20  
HEX BOLT  
REPEAT  
0
+10  
19  
18  
17  
16  
12  
13  
SUBTITLE  
LOC  
MUTE  
ANGLE  
OSD  
AUDIO  
ST  
TITLE/PBC  
A/P  
DSP  
CLK  
14  
15  
18. OSD BUTTON  
10. PLAY/PAUSE BUTTON  
KEY PLATE  
19. SUBTITLE AND LO/DX BUTTON  
20. REPEAT BUTTON  
11. NUMBER/PRESET  
MEMORY BUTTONS  
12. ANGLE BUTTON  
PLASTIC TRIM OUT  
KEY PLATE  
21. STOP BUTTON  
13. MUTE/LCD COLOUR BUTTON  
14. CLOCK BUTTON  
22. VOLUME - BUTTON  
23. JOG LEFT BUTTON  
24. VOLUME + BUTTON  
25. ENTER BUTTON  
15. DISPLAY/SUBWOOFER  
BUTTON  
16. TITLE/PBC AND A/P BUTTON  
17. AUDIO AND ST/MO BUTTON  
24  
7
DESCRIPTTION OF LCCDD ON THE FROONT PANEL  
12  
11  
13  
10  
5
6
7
4
9
DYNAMIC  
FULL  
6/8  
4/8  
2/8  
OFF  
TITLE  
CHP TRK  
RDM LOUD DTS  
DIGITAL  
CH  
CLAS  
POP  
ST  
INT RPT  
LOC  
PRG  
ROCK VIDEO  
OFF  
ON  
PRO LOGIC  
2
1
14  
15  
16  
17  
3
8
AUTO  
1. DVD/VCD/CD/MP3 indicators  
2. Operating statusindicators (play orpause)  
LPCM 48K  
LPCM 96K  
LPCM OUTPUT  
3. Repeat playbackindicators (single orall for DVDdisc, single forVCD/CD disc,  
single, folder andall for MP3disc)  
4. Title number indicator  
5. Chapter numberindicator  
3). The setup items of each setup item in the PREFERENCES setup  
menu show like the following:  
6. Disc playingtime indicator for DVD/VCD, track timeindicator for CD/MP3.  
7. Dolby digitalindicator  
MULTI  
NTSC  
PAL  
TV TYPE  
8. Viewing in different angle indicator  
9. Disc rotation indicator  
10. RANDOM indicator  
DEFAULTS  
RESET  
11. LOUDNESS indicator  
12. DTS digitaloutput indicator  
13. SPECTRUM indicator  
4. Press JOG button to select the setup item and then press ENTER  
button to make it effective.  
14. CLASSIC, POPand ROCK equalizer curves indicators  
15. STEREO indicator  
16. LOCAL stationindicator  
17. SCAN discindicator  
23  
8
1). The setup items of each setup item in the GENERAL setup menu  
show like the following:  
DESCRIPTIION OFF THE BBAACK OF TTHE FRRONT PANEL  
NORMAL/PS  
NORMAL/LB  
WIDE  
TV DISPLAY  
AUTO  
HI-RES  
N-FLICKER  
PIC MODE  
EJ  
ON  
OFF  
ANGLE MARK  
OSD LANG  
ENGLISH  
CHINESE  
1
EJECT BUTTON: Press it to eject the disc from compartment.  
ON  
OFF  
CAPTIONS  
ON  
OFF  
SCR SAVER  
LOADING THHE BATTTTERY INN THE REEMOTE CCONTROLLER  
REMOTE CONTROL BASICS BATTERY REPLACEMENT  
1.Remove the battery holder as the direction indicated by the arrow.  
2.Replace the battery Set a new battery property with (+)side up as  
illustrated.  
2). The setup items of each setup item in the AUDIO setup menu  
show like the following:  
ANALOG  
SPDIF/RAW  
SPDIF/PCM  
AUDIO OUT  
3.Insert the battery holder. Push in the holder to the original position.  
NOTE ON BATTERIES  
1.Old batteries must immediately be removed and disposed.  
2.Improper use of batteries may cause overheating, explosion or ignition.  
Resulting in jury or fire .  
LINE OUT  
F
R REMODE  
OP MODE  
3.Battery leakage may cause damage to the unit.  
4.Do not disassemble or short the batteries.  
5.Do not throw the batteries into the fire.  
STEREO  
DUAL MONO  
L-MONO  
R-MONO  
MIX-MONO  
6.To avoid the risk of accident, keep the batteries out of reach of children.  
22  
9
CONNECTING  
AUDIO  
SETUP  
2).  
POWER AND SPEAKERS OUTPUT  
AUDIO OUT  
OP MODE  
DUAL MONO  
DYNAMIC  
ANTENNA PLUG  
PRO LOGIC  
LPCM OUTPUT  
10A  
WOOFER LINE OUT  
YELLOW  
YELLOW  
MEMORY B+  
FUSE  
MAIN PAGE  
??????(display the selected item)  
BLACK(GND)  
1A  
RED  
RCA LINE OUT  
RED R  
IGNITION SWITCH  
FUSE  
WHITE L  
1A  
BLUE AUTO ANT  
3).  
FUSE  
PREFERENCES PAGE  
FRONT  
+
+
+
GRAY  
WHITE  
FRONT  
TV TYPE  
DEFAULTS  
WHITE / BLACK  
GREEN  
GRAY / BLACK  
VIOLET  
RIGHT  
SP  
LEFT  
SP  
+
REAR  
REAR  
VIOLET / BLACK  
GREEN / BLACK  
MAIN PAGE  
??????(display the selected item)  
NOTE:  
In spite of having any kinds of speaker system, must use 4 ohms  
impedance of speaker to reduce the distortion during high volume  
level.  
3. In one of the above setup menu, press JOG up or down button to  
select setup item, so the TV screen will show the setup items of  
the selected setup item on the right side of the selected setup  
item(select MAIN PAGE item and then press ENTER button to  
return back to SETUP MENU). These setup items menu of each  
one of the GENERAL, AUDIO SETUP and PREFERENCES setup items  
like followings:  
10  
21  
GLOSSARY  
RESET DISTORTED PROGRAM  
When the program of the DVD player is distorted or the disc in the slot  
can not be ejected, press OPEN button on the front panel to flip down  
the front panel from the DVD player, then take away the front panel  
from the DVD player and then press the RESET button on the front  
facet of the unit chassis to rehabilitate the distorted program to zero;  
finally install the front panel back to the previous position in the DVD  
player.  
Title: The longest sections of a picture or a music piece or a  
movie etc on a DVD. Each title is assigned a title number  
enabling you to locate the title you want.  
Track: The sections of a picture or a music piece on a VCD or  
CD. Each track is assigned a track number enabling you  
to locate the track you want.  
SETTING UP SYSTEM  
1. Press MENU button on the IR remote controller to display the  
following settings menu on the TV screen:  
Chapter: A complete section of a picture or a music piece on a  
DVD that are smaller than a title. A title is composed of  
several chapters. Each chapter is assigned a chapter  
number.  
SETUP MENU....MAIN PAGE  
GENERAL SETUP  
AUDIO SETUP  
PREFERENCES  
Caption: The language displayed at the bottom of the TV screen,  
normally the translation or the dialogue, which are also  
recorded on the disc.  
EXIT SETUP  
??????(display the selected item)  
Angle: Some DVD disc are recorded from different angles so  
that users can view the same scene from different angles.  
2. Press JOG up or down button to select the SETUP item in the  
settings menu, then the DVD player will display the following  
settings menus on the TV screen (select EXIT SETUP item and then  
press ENTER button to exit setting menu to resume normal playback)  
1).  
GENERAL  
PAGE  
TV DISPLAY  
PIC MODE  
ANGLE MARK  
OSD LANG  
CAPTIONS  
NORMAL/PS  
NORMAL/LB  
WIDE  
SCR SAVER  
MAIN PAGE  
??????(display the selected item)  
20  
11  
TO SELECT THE FIRST TRACK/CHAPTER TO PLAY  
SAME FFUNCTTION BUTTONNS IN DDISC OORR RADIO MODE  
1. In the state of VCD/CD/MP3 disc playing, press the 1TOP button  
on the front panel to select the first track/chapter to play.(depend  
on the disc used for VCD)  
1. POWER BUTTON  
Press the POWER button on the front panel or the remote controller  
to turn on the unit.  
2. MODE BUTTON  
2. In the state of DVD disc playing, the 1TOP button is not available.  
Press the MODE button on the front panel or the remote controller  
to select DISC or RADIO mode.  
3. AUDIO MODE AND LEVEL BUTTONS  
TO SCAN DISC  
Press the SEL button on the front panel or the remote controller  
to select the audio mode such as VOL, BASS, TREBLE, BALANCE  
and FADER, then press the + or - button on the front panel or the  
remote controller to adjust the level of them.  
1. In the state of VCD/CD disc playing, press the 3INT button  
on the front panel to play the previous 10 seconds part of each  
track/chapter on disc.(depend on the disc used for VCD)  
4. MUTE/LCD COLOUR (EFFECT ONLY FOR MULTI-COLOUR LCD, NO  
EFFECT FOR BLACK MASK LCD) BUTTON  
2. In the state of DVD/MP3 disc playing, the 3INT button is not  
available.  
Press the MUTE button on the front panel or the remote controller  
to eliminate the sound immediately and the audio mute indicator on  
the LCD will be flashed, press it again to resume the normal playback.  
Press it hold for more than 2 seconds to turn on or off the LCD FLASH,  
and the LCD will show FLASH ON or FLASH OFF. When in FLASH ON  
mode, the LCD will change the LCD light colour alternatively. When  
finding your desired LCD flash colour, press it hold for more than 2  
seconds again to select the LCD light colour and stop flashing.  
5. CLOCK DISPLAY AND ADJUSTMENT BUTTONS  
Press the CLK button on the front panel or the remote controller  
to display time on LCD. Press the CLK button hold for about 2 seconds  
to flash HOUR, then press the + or - button on the front panel or the  
remote controller to adjust HOUR, then press the SEL button to flash  
MINUTE, then press the + or - button to adjust MINUTE.  
6. DSP/SUBWOOFER BUTTON  
TO PLAY DISC IN RANDOM  
1. In the state of VCD/CD/MP3 disc playing, press the 4RDM button  
on the front panel to play in random or select DISC REP.(depend on  
the disc used for VCD)  
2. In the state of DVD disc playing, the 4RDM button is not available.  
CHANGING LANGUAGE TYPE  
Press the DSP button on the front panel or the remote controller  
to select the preset music equalizer curves: FLAT, POP, CLASSIC  
and ROCK. The sound effect will be changed.  
1. In the state of DVD disc playing, press the AUDIO button repeatedly  
on the IR remote controller to select the desired language type.  
(depend on the disc used)  
Press it for more than 2 seconds to turn on(default) or off the sub-  
woofer.  
7. OPEN BUTTON  
Press the OPEN button on the front panel to flip down the front  
panel from the unit, then you can insert the disc into the disc  
compartment or press the EJECT button on the back of the front  
panel to eject the disc or take away the front panel.  
8. IR REMOTE SENSOR  
2. In the state of MP3 disc playing, the AUDIO button on the IR remote  
controller is not available.  
3. In the state of VCD/CD disc playing, press the AUDIO button  
repeatedly to select STEREO, MONO LEFT and MONO RIGHT sound  
mode, no language function.  
12  
19  
RADIO OPERATION  
USE OF PAD NUMBERS  
1. PRESET STATION [ 1-6 ] BUTTONS  
A]. To memorize the current frequency, press any one of the six preset  
buttons(1-6) on the front panel or on the remote controller hold for more  
than 2 seconds.  
1. In the state of VCD disc playing, press PBC button on the IR  
remote controller to turn PBC function ON/OFF:  
1).When it is in the state of PBC ON and display the title menu on the TV  
screen if the disc include TITLE MENU, press one of NUMBER buttons  
to select the track/chapter to playback; During playing, the NUMBER  
buttons are not available.  
B]. To recall the preset memory, press one of the preset buttons [1-6].  
2. AS/PS BUTTON  
When shortly pressing the APS button on the front panel or the A/P button on  
2).When it is in the state of PBC OFF, press one of the NUMBER buttons  
to select the chapter/track to playback.  
the remote controller, the radio searches for each preset station. When the field  
strength level is more than the threshold level of stop level, the radio is holding  
at that preset number for few seconds with releasing mute, and then searches  
again. In FM band, FM 1,FM 2 and FM 3 is checked one at a time.  
When long pressing the APS or A/P button (more than 1 second), the radio  
searches from the current frequency and checks the signal strength level until  
1 cycle search is finished. And then 6 strongest stations are preset to the  
corresponding preset number. The AS operation is implemented in the each  
band of selected band. When the AS operation is finished, the radio executes  
the preset scan.  
2. In the state of DVD disc playing, press TITLE button to display the  
title menu; then press the NUMBER button to select the chapter/  
track to playback.  
3. In the state of CD/MP3 disc playing, press the NUMBER button to  
select the chapter/track to playback.  
*
*
+10 BUTTON: Press it once to display 1-, then press one of 1-9  
NUMBER buttons to select one of the 11th-19th tracks. Press it  
twice to display 2-, then press one of 1-9 NUMBER buttons to  
select one of the 21th-29th tracks. Press one of 1-9 NUMBER  
button and then press +10 button to display 1- again(depend on the  
disc used).  
The 1-6 digital buttons on the front panel have not the function of  
selecting track/chapter to playback, but the 1-4 digital buttons on  
the front panel have the function of TOP, RPT, INT and RDM.  
3. LOC BUTTON(effect only for FM)  
If you find that the signal is weak and the listening effect is bad when tuning for  
the distance station, check whether the word LOC is displayed on LCD. If the  
word LOC is displayed on LCD, press the LOC button on the front panel or the  
remote controller to turn off LOC function, then tune for distance radio station  
again.  
If you find that the signal is so strong that the interfere is stronger when tuning  
for the local station, check whether the word LOC is displayed on LCD. If the word  
LOC is displayed on LCD, press the LOC button to turn on LOC function, then  
tune for local radio station again.  
4. BAND and PAL/NTSC BUTTON  
VIEW IN DIFFERENT ANGLE  
In RADIO mode, press it repeatedly on the remote controller or the BND button  
on the front controller to select your desired radio band and word which band  
is selected will be displayed on LCD.  
1. In the state of VCD/MP3/CD disc playing, the ANGLE button on  
the IR remote controller is not available.  
In DISC mode, press it repeatedly to select PAL or NTSC mode.  
2. In the state of DVD disc playing, press TITLE button on the IR remote  
controller to display TITLE MENU on TV screen, then select ANGLE  
FUNCTION item and then press ENTER button on the IR remote  
controller to turn into ANGLE function playing mode, then press the  
ANGLE button repeatedly on the IR remote controller to view in  
different angle.(depend on the disc used)  
5. TUNE/SEEK UP/DOWN BUTTONS  
Press UP or DN button on the remote controller or ^ or v button on the front  
panel to manually tune up or down for your desired station. Press them hold for  
more than 2 seconds to automatically tune up or down for the stronger station.  
6. STEREO/MONO BUTTON  
Press the ST button on the remote controller to select STEREO or MONO sound  
mode.  
18  
13  
IN THE STATE OF MP3 DISC PLAYING  
DISC BASIC OPERATION  
Press the REPEAT button on the IR remote controller or the 2RPT button on the  
front panel to select REPEAT ONE, FOLDER REPEAT or DISC REPEAT. Press the  
PLAY/PAUSE button to resume the normal playback.(The defaulted repeat mode  
is DISC REPEAT).  
TO TURN ON TO PLAY  
1. Connect the DVD player into the video monitor and adjust the video  
monitor to make it to be in good state of COLOUR, BRIGHTNESS  
and so on.  
IN THE STATE OF CD DISC PLAYING  
Press the REPEAT button on the IR remote controller or the 2RPT button on  
the front panel to select REPEAT ONE, DISC REPEAT(defaulted repeat mode).  
2. Press POWER button on the remote controller or the front panel  
of the DVD player to turn on the DVD player, then the DVD VIDEO  
will displayed on TV screen(if it is in disc mode).  
TO CHANGE THE LANGUAGE OF THE CAPTION  
In the state of DVD disc playing, press SUBTITLE button repeatedly to select  
the language of the caption or turn off the caption.(depend on the disc used.)  
3. Press OPEN button on the front panel of the DVD player to flip  
down the front panel, then insert the disc in the slot with the label  
side upward. When the disc is inserted halfway, it is automatically  
pulled into the unit. At the moment, the TV screen will show DISC  
LOADING, then PLAY in the upper left corner and the DVD LCD will  
show disc rotation indicator, DVD/CD/VCD/MP3 (depend on the  
disc species) indicator, playing indicator(depend on disc species),  
title number indicator(depend on disc species), chapter number  
indicator(depend on disc species) and disc playing time indicator.  
Some discs may automatically start playback from the first chapter  
/track. Some discs will automatically start playback by displaying  
the disc title menu on TV screen.  
In the state of VCD/CD/MP3 disc playing, the button is not available.  
TO CHECK TITLE, CHAPTER SEQUENCE NUMBER OR PLAYING TIME  
1. In the state of DVD disc playing, press the OSD button repeatedly on the  
remote controller to display the title, chapter sequence number or different  
species of time about current playing disc, such as TITLE REMAIN time,  
CHAPTER ELAPSED time and CHAPTER REMAIN time.  
2. In the state of CD disc playing, press the OSD button repeatedly on the  
remote controller to display the different species of time about current  
playing disc, such as SINGLE ELAPSED time, SINGLE REMAIN time, TOTAL  
ELAPSED time, TOTAL REMAIN time, then checking time OFF.  
4. When displaying the DVD title menu on TV screen, press PLAY/  
PAUSE button on IR remote controller or the front panel of the DVD  
player to play the defaulted first track/chapter; or press JOG  
buttons to select track/chapter in the DVD title menu and then  
press ENTER button on the IR remote controller or PLAY/PAUSE  
button on the IR remote controller or on the front panel of the DVD  
player to play the selected track/chapter.  
3. In the state of MP3 disc playing, press the OSD button repeatedly on the  
remote controller to display the different species of time about current  
playing disc, such as SINGLE ELAPSED time, SINGLE REMAIN time.  
4. In the state of VCD disc playing:  
*
When playback a double-sided DVD video disc, insert the disc with  
top side up. Play it back in its entirety, then take out the disc and  
turn it over to play the second side. (The top and back side of a DVD  
video disc are marked differently on different discs)  
1).When in the state of PBC ON, press the OSD button repeatedly on the remote  
controller to display the different species of time about current playing disc,  
such as SINGLE ELAPSED time, SINGLE REMAIN time, and then OFF.  
2).When in the state of PBC OFF, press the OSD button repeatedly to display the  
different species of time about current playing disc, such as SINGLE ELAPSED  
time, SINGLE REMAIN time, TOTAL ELAPSED time, TOTAL REMAIN time,  
then checking time OFF.  
14  
17  
TO SELECT NEXT OR LAST CHAPTER/TRACK TO PLAY  
TO PAUSE THE PLAYBACK  
1. Press the F.FWD/NEXT button on the IR remote controller or the  
^ button on the front panel during playback to select the next  
chapter/track to playback.  
In the state of DVD/VCD/CD/MP3 disc playing, press the PLAY  
/PAUSE button on IR remote controller or the front panel of DVD  
player to pause the playback, press the PLAY/PAUSE button again  
to resume normal playback.  
NOTE: PRESS THE F.FWD/NEXT OR ^BUTTON MULTIPLE TIMES TO  
ADVANCE MULTIPLE CHAPTERS FORWARD.  
2. Press the F.BWD/PREV. button on the IR remote controller or the  
v button on the front panel during playback to select the last  
chapter/track to playback.  
TO STOP THE PLAYBACK  
NOTE: PRESS THE F.BWD/PREV. OR V BUTTON MULTIPLE TIMES  
TO ADVANCE MULTIPLE CHAPTERS BACKWARD.  
*
*
The sound is muted during chapter/track forward or backward.  
While in chapter/track forward or backward the display status  
screen is activated along the top of the screen.  
In the state of DVD disc playing, press the STOP button once on IR  
remote controller to stop the playback, then press the PLAY/PAUSE  
button to resume the normal playback; press the STOP button twice to  
full stop the playback, then press the PLAY/PAUSE button to start  
playback from the first chapter/track of the disc.  
*
For VCD disc, when PBC ON, the PREV. button is not available.  
TO REPEAT PLAYING  
In the state of MP3/CD disc playing, press the STOP button on IR  
remote controller to stop the playback. Then press the PLAY/PAUSE  
button to resume the normal playback.  
IN THE STATE OF DVD DISC PLAYING  
In the state of VCD disc playing, press PBC button on the IR remote  
controller to turn PBC function ON/OFF:  
Press the REPEAT button on the IR remote controller or the 2RPT  
button on the front panel to select CHAPTER REPEAT, TITLE REPEAT  
or REPEAT OFF.  
1. When starting to turn on PBC function, it will play from the beginning  
of disc(it will display title menu on TV screen if the disc include title  
menu, then press NUMBER or NEXT button to select chapter/track  
to play). During playback, the STOP button is not available. (For some  
discs, when it is in PBC on, press STOP button to return back to title  
menu during playback.)  
IN THE STATE OF VCD DISC PLAYING  
Press PBC button on the IR remote controller to turn PBC function  
ON/OFF(the defaulted mode is PBC OFF):  
1. When it is in the state of PBC ON, during playing, the REPEAT  
button on the IR remote controller or 2RPT button on the front  
panel are not available.  
2. When it is in the state of PBC OFF, during playing, press the  
REPEAT button on the IR remote controller or 2RPT button on the  
front panel to select REPEAT ONE or REPEAT OFF.  
2. When starting to turn off PBC function, it will also play from the  
beginning of disc(it will not display title menu on TV screen even if  
the disc include title menu). During playback, press the STOP button  
to stop playback, and then press the PLAY/PAUSE button to play  
from the beginning of disc again.  
TO MUTE  
16  
15  
DISC ADDVANCEED OPERRATION  
TO END PLAYING  
TO SELECT PLAYING CONTENTS WITH THE MENU  
If the disc includes the title menu:  
1. Press OPEN button on the front panel of the DVD player to flip down  
the front panel, then press EJECT button on the back of the front  
panel of DVD player to eject the disc from the slot and take away the  
disc.  
In the state of DVD disc playing  
1. press TITLE button on the IR remote  
controller to display title menu on the TV screen.  
2. Press JOG button on the IR remote controller to select your desired  
chapter/track or other icon; or press number button to select your  
desired chapter/track to playback.  
3. Press ENTER button on the IR remote controller to play the selected  
chapter/track; or to display the subtitle menu on the TV screen, then  
press JOG button to select your desired chapter/track or other icon,  
then press ENTER button to play the selected chapter/track.  
2. Press the POWER button on the IR remote controller or the front  
panel of the DVD player to turn off the DVD player.  
NOTE:  
In the state of CD disc playing  
The TITLE, JOG and ENTER buttons are disabled.  
In the state of DVD/VCD/CD/MP3 disc playing, if the power  
button or the ignition is shut off and then turn on the power or  
the ignition, the DVD player will resume play at the exact spot  
where playback was interrupted.  
In the state of VCD disc playing, press PBC button to turn PBC on or off.  
1. When starting to turn on PBC function, it will play from the beginning of disc  
till it display title menu on TV screen if the disc include title menu.  
For some VCD discs, when it is in PBC on, press STOP button to return back  
to title menu during playback. Then press the NEXT or NUMBER button to  
select track/chapter to playback.  
2. When starting to turn off PBC function, it will also play from the beginning  
of disc, but it can not show the title menu.  
In the state of MP3 disc playing:  
1. After inserting the MP3 disc into the disc slot and then the title menu be  
showed on TV screen; then press JOG button to select your desired FOLDER,  
then press ENTER button to display the subtitle menu on the TV screen, then  
press JOG button to select your desired track, then press ENTER button to  
play the selected track to playback.  
NOTE:  
1. If the DVD player can not convey the disc to the reading position  
after inserting disc into disc compartment, press EJECT button  
hold for more than about 3 seconds to make the DVD player convey  
the disc to the reading position.  
2. During playing, the TITLE, JOG and ENTER buttons are not available, you can  
press the digital buttons to select the track to playback.  
FAST FORWARD OR REVERSE PLAYING  
2. If the DVD player can not eject out the disc from the disc compart-  
ment after pressing EJECT button shortly, press EJECT button  
hold for more than about 3 seconds to make the DVD player eject  
out the disc from the disc compartment.  
Press the F.FWE/NEXT or F.BWD/PREV. button continuously on  
the IR remote controller or the ^ or v button on the front panel hold  
during normal playback to fast play forwards or backwards.  
*
While in rapid preview or rapid review the display status screen in  
activated along the top of the screen.  

Radio Shack SYSTEM 440 User Manual
Pioneer GM X374 User Manual
Panasonic WV 7130D User Manual
Panasonic NV DS60 User Manual
Panasonic AJ SPC700 P User Manual
Makita DP4002 User Manual
Kicker DS6930 User Manual
JVC LVT1405 002A User Manual
JVC KD KD R210 User Manual
JVC GY HM750U User Manual