RCA SOLAM VIDEO CAMERA User Manual

PROPER USE AND CARE OF YOUR  
Capturing real-time  
images of the Sun,  
White, H-alpha &  
Calcium light.  
ASTROVID SolarCam™ ASTRONOMICAL  
CCD VIDEO IMAGING SYSTEM  
Congratulations on the purchase of the ASTROVID SolarCam™ VIDEO  
CAMERA! This is a high quality Astronomical CCD Video Imaging System  
with 2/3 inch monochrome CCD that will provide you with the best full disk  
and high resolution Solar Viewing possible. With proper care this system  
should last many years and provide excellent images!  
SAFETY PRECAUTIONS:  
1. Use only the power transformer supplied with the camera. Use of any  
other power transformer will damage the camera and invalidate the Warranty.  
2. A portable 12 volt battery pack can be used if there is a 0.5 (500 milliamp)  
amp fuse wired in series with the positive lead. We also found that an  
excellent way to use the cameras in the field is to use a 110 volt inverter. These  
are available from either Wal-Mart or K-mart for less than $50.00.  
3. Avoid static electricity discharges. These  
may damage the CCD chip.  
4. Do not point the CCD towards the Sun  
unless protected with a proper solar filter  
or Herschel Wedge. Permanent damage to  
the CCD chip will result if the CCD is not protected.  
5. Do not directly touch or attempt to clean the CCD chip.  
6.The thread mount on the CCD camera has fine threads. Do not force it onto  
the 1.25"-C adapter, T-C adapter, or lens mount.  
7. In our use of the T-C adapter we have found that at times small metal flakes  
from the T-adapter threads will end up on the protective glass that covers the  
CCD chip. When using your camera they will show up as irregular opaque black  
dots on the screen. They can either be blown off using an Air Syringe Bulb  
available at drugs stores or by using a very soft artist’s paintbrush to carefully  
dust them off.  
8. Keep the cover on the camera when it is not in use.  
9. Treat the ASTROVID SolarCam™ camera as a fine piece of equipment and  
it will give you many years of enjoyment.  
Please note: Camera setup will immediately follow the next section.  
PLUGGING INTO THE UNIVERSE:  
Your results will depend greatly on “seeing conditions” at the time of  
observation.  
1. A T-C or 1.25"-C adaptor is required to attach the video camera to the  
telescope.  
2. The camera can be attached directly to the telescope via the T-C adapter or  
via a 1.25"-C adapter into an eyepiece holder for prime focus videography.  
3. If closer views are desired, either a barlow or stacked barlows with the 1.25"-  
C adaptor or an eyepiece projection setup must be used.  
4. Eyepiece projection or Barlow enlargement can be used for closer views of  
prominences and sunspot detail.  
ASTROVID SolarCam™ CCD VIDEO CAMERA  
CAMERA CONNECTIONS:  
***The power supply is to be connected last to prevent any damage to the camera.***  
1. This camera cannot be hooked directly to a television for a picture as it only supplies Baseband or  
Composite Video.  
2. Most newer televisions have separate Video In jacks that can be used with this camera.  
3. Look at the back of the Astrovid SolarCam™ camera.  
4. On the back is a 12 pin female jack labeled DC IN. The round male metal jack on the black power cord  
goes into the ASTROVID SolarCam™. It attaches to the back of the camera’s DC IN jack. Line up the pins  
to match the connector, be careful in doing this so as not to bend any of the pins within the connector. Push  
in the power cord to lock. DO NOT force this connection . Not plug in the wall transformer until all of  
your connections are made.  
5. Plug in the mini-phono plug from the wall transformer power supply into the power cord that is now  
attached to the DC IN.  
6. Connect the white Composite video cable’s Male BNC connector to the back of the SolarCam™ camera’s  
female BNC connector labeled Video.  
7.The other end of the white video cable has a Male RCA Adapter that can be plugged into a VIDEO IN  
jack for a television, camcorder, or VCR. (please note set VCR or TV to line in or video in)  
10. Our monitors come with the same BNC jacks as the camera. So if you are using our monitor you will  
need 1 BNC to F-adapter. The RG-59 cable can then be screwed into the VIDEO INPUT JACK on the  
monitor. There is another BNC jack on the monitor for VIDEO OUTPUT. From here using another cable with  
a BNC on one end and an RCA adapter on the other end, you can plug  
into a VCR or Camcorder to simultaneously watch and record your  
With total manual control  
and  
large  
2/3  
inch  
observations. Using this configuration with one of our 850 line high  
resolution monitors will give the best results from the ASTROVID  
StellaCam™.  
11. Once all of the cables and adapters are plugged in, you may  
plug the power supply in.  
monochrome  
ASTROVID  
CCD the  
SolarCam™  
provides the most flexibility  
and largest field of view  
possible!  
ASTROVID SolarCam™ Camera  
Controls  
The use of the separate camera controls will enable the image to gain fine adjustment of the final image. It  
will allow the user to view both solar surface detail and prominences. The use of a monochrome 2/3 inch  
format video CCD will give the largest field of view possible. This will enable full disk viewing on many more  
telescopes. See also the separate specification sheet for parameters of each camera control function.  
The following controls on the camera are detailed as follows:  
Manual Shutter Speed Dial: Round dial labeled 0-9on back upper left corner of the camera. Use the  
mini screwdriver provided to change the shutter speeds. Shutter speeds go from 1/60 second to 1/10000  
second. Position 0-7. Position 8 Filed integration 1/60 second or Frame Integration 1/30 second. Position  
9—no use.  
.
Internal External Sync Switch: Horizontal switch labeled INT EXT. Just to the right of the Shutter  
Speed Dial. Not really used for Solar Imaging. Leave switch to the left on internal.  
Gamma On Off Switch: Vertical switch labeled V ON OFF. Just to right of Internal external sync switch.  
This will control the gamma, which relates closely to the contrast of the image. In the off position the gain is  
adjusted to the normal daylight conditions (gamma 1.0) . In the ON position the gamma is increased. This  
will give a higher contrast image and is useful for solar surface detail. You may want to experiment in both  
positions as the use of various neutral density and colored filters i.e. blue and green will also affect the  
contrast.  
ASTROVID SolarCam™ CCD VIDEO CAMERA  
DC IN Plug: This is the 12 pin hi-rose connector on the upper right of the camera. This is where the DC  
power plug goes into the camera.  
Mini Dip Switch Panel: Center left of camera. Rectangular box containing six dip switches. All six dip  
switches should be in the up position for proper operation of the camera. You do not need to change the  
position of these dip switches.  
GAIN Dial: Dial next to mini dip panel labeled GAIN A, F, M. This three position dial allows you to  
change the gain settings. Gains relates to the strength of the video signal. An increase in gain also  
increases the noise in the background of the image. The goal of the gain control is to manually adjust it to  
keep it as low as possible. The adjustment of the gain in done in conjunction with the adjustment of the  
shutter speeds. It is preferred to use as high a shutter speed as possible so as to overcome some of the  
atmospheric seeing or turbulence of the atmosphere.  
The three gain settings are A – Auto Gain varies from 0 dB to 20 dB depending on the light conditions.  
F—Fixed Gain—with the gain set at 13 dB  
M—Manual Gain The gain is manually adjusted from 0-20 db. You do this by placing the dial in the M  
position with the mini screwdriver. Once this is done you will use the yellow pot labeled M.GAIN (manual  
gain) in the lower right corner of the camera to manually adjust the gain. Rotating clockwise will increase  
the gain. Rotating counterclockwise will decrease the gain.  
75 OHM On/OFF Switch: Vertical Switch on bottom left hand side of camera labeled 75 ohm ON/OFF.  
Should be left in the OFF position for most imaging. You may turn  
VIEW AND RECORD YOUR  
IMAGES AT THE SAME TIME!  
SHOW THE WONDERS OF  
THE SUN TO LARGE GROUPS  
AT ONE TIME!  
it on if you are passing through a monitor and going to a recording  
device or if you are running very long distances of video cable. You  
can experiment turning the switch on and off once you have your  
image on the screen.  
Trigger Switch: This is the vertical switch at the bottom labeled  
TRIG + - Used for external triggering of the camera. Not generally used for Solar Imaging. Leave in the -  
position.  
VIDEO BNC Connector: Round Female Video BNC Connector labeled VIDEO. This is the EIA  
monochrome video output for the camera. It goes to any TV, Monitor, VCR, Recorder, Frame Grabber etc.  
Manual Gain: Yellow Dial labeled M.GAIN. Used when making manual gain adjustments. Use after  
setting the gain dial to M for manual. See above please.  
USING YOUR ASTROVID SolarCam™ ( Part 1) :  
Because solar imaging is a little more involved than other planetary and lunar imaging. It is  
recommend that once you achieve your best images, you make note of your setup. i.e. camera  
settings , gain, shutter, gamma, filters used etc.  
1. Make all of your camera connections and plug in the power.  
2. Mae sure you have you telescope setup with proper solar protection for both your eyes an the  
SolarCam™.  
3. Attach the camera to the telescope via the 1.25 inch adapter.  
4. Adjust the shutter speed to the position labeled 0. This is the 1/60 second shutter speed.  
5. Put the Gain A,F,M button to the manual position. Rotate the M. Gain button clockwise to the full 20dB  
position  
©AVA ASTRO CORP 2001  
ASTROVID SolarCam™ CCD VIDEO CAMERA  
-3-  
USING YOUR ASTROVID SolarCam™ (Part 2 Solar Surface Detail):  
1. Point your telescope towards the Sun. The easiest way to begin is to find your focus by finding the edge of  
the sun.  
2. By initially adjusting the settings as discussed in part 1, the sun should appear overexposed and bright  
white. Once you know the sun is on the screen, turn the gain down by rotating the M.GAIN button counter-  
clockwise. You may have to move the telescope until you find the edge of the sun. Once you think you  
have the edge of the sun you can check it by increasing the shutter speeds. This will act to dim the image.  
This is done by rotating the shutter speeds from positions 0-7.  
3. It is very easy to overexpose the sun using such sensitive cameras. So often what looks like the edge of  
the sun is actually an overexposed over-flowing image. By decreasing the gain and/or increasing the shut-  
ter speeds you should be able to find the edge of the sun.  
4. Once you have the edge of the sun in focus, you can re-center the disk of the sun by moving your tele-  
scope.  
5. When the disk of the sun is on the screen you can start to make adjustments to your image. The three ad-  
justments you will make will be the Gain (manual), Shutter speed and Gamma.  
6. Start by adjusting the gain and shutter speeds. The goal here is to keep the gain as low as possible and to  
keep the shutter speed as high as possible. This is often going to be a slight compromise.  
7. Once you have adjusted the gain and shutter speed you can then adjust the gamma. You can go from low  
contrast to high contrast. Increasing the contrast will show more solar surface detail.  
8. You can also adjust the impedance to see if it improves the image ore not. This is the vertical switch la-  
beled 75 ON / OFF.  
9. To further enhance the image you can see below the section on using filters.  
USING FILTERS TO ENHACE SOLAR SURFACE DETAIL:  
We tested several filter combinations to achieve the best solar surface detail. We recommend the following.  
White Light Surface Detail:  
1. We recommend using the Baader 1.25 inch contrast booster that is mated with the Baader 1.25 inch UVIR  
blocker.  
2. You may also use the Baader Solar continuum filter with the Baader UVIR blocker. The Baader Solar con-  
tinuum filter also works very well visually.  
3. You can also use neutral density filters.  
Hydrogen Alpha and Calcium Light Surface Detail:  
1. We recommend using the Baader 1.25 inch contrast booster that is mated with the Baader 1.25 inch UVIR  
blocker.  
2. You may also use the Baader Solar continuum filter with the Baader UVIR blocker. The Baader solar con-  
tinuum filter also works very well visually.  
3. You can also use Blue and Green filters if you have them as they will act as Neutral Density filters in H-  
alpha light.  
4. For Calcium light you can use red and green filters as these will act as Neutral Density filters.  
5. If you have a set of imaging filters you can use the colored filters from these sets. Some of the sets have  
built-in IR blocking and others do not.  
ASTROVID SolarCam™ CCD VIDEO CAMERA  
USING YOUR ASTROVID SolarCam™ (Part 3 Hydrogen-alpha Prominence Detail):  
-5-  
1. Solar prominences are imaged in Hydrogen alpha light. Solar prominences are much dimmer than the  
surface detail found on the sun.  
2. The majority of observed solar prominences do not change in appearance very quickly. However, you  
may be able to find one of the changes morphology in rapid time.  
3. Gain becomes the more important parameter in imaging solar prominences. An increase of gain will  
boost the signal bringing out the much fainter prominences. This is done by increasing the manual  
gain.  
4. Increase the manual gain until you see a prominence.  
5. You also want to decrease the shutter speed as you make your initial adjustments to allow the promi-  
nences to come into view.  
6. Once a prominence appears on screen you can start to make adjustments to your image.  
7. You can see that if the gain is increased you start to lose some of the fine detail (burning it out) but  
bring out the fainter structures  
8. The goal is to adjust the gain so that the most amount of detail can be imaged in the prominence.  
9. Again, you will find that you need a balance between gain and shutter speeds. However, this time the  
gain will be set higher and the shutter speeds will most likely be lower.  
10. The Solar Hydrogen -alpha line is a very narrow wavelength in a more atmospheric stable part of the  
spectrum. The use of slower shutter speeds will not always decrease the resolution of the promi-  
nences.  
11. The human eye has an incredible response to light in terms of dynamic range. The eye can look at ob-  
jects going from black to bright white in the same image. A camera cannot do that. Cameras have a  
more limited dynamic range. So often with H-alpha imaging you will not see the prominences and so-  
lar surface detail at the same time.  
12. To better view Solar prominences it is often desirable to increase your image scale. This involves using  
a Barlow lens or Powermate from TeleVue. A Powermate is a better choice as it is more corrected and  
will not change your focal point. The only drawback here is that in some of the wide field h-alpha tele-  
scopes apply a Barlow is not always beneficial. However, on Solar scopes with already longer focal  
lengths using a Powermate or Barlow lens is generally beneficial.  
USING FILTERS FOR H-ALPHA PROMINENCES  
1. The main filters used for prominences are neutral density filters. However, in long focal lengths they  
would be less likely to be used than in short wide field telescopes.  
2. Again, for neutral density filters you can use a green or blue filter on wide-field telescopes.  
3. Because the setups for solar imaging vary so much, some experimentation is need here to determine  
whether a filter is needed or not for your particular setup.  
4. Keeping notes of your results will help in saving time for setup and will lead you to the best possible  
images.  
Enjoy Your Astrovid SolarCam™!!!!  
Be sure to try it on the Moon and Planets Also!!!  
© AVA Astro Corp 08/09/2005 jec  

RCA EZ3000BL User Manual
PYLE Audio View Series PLTDN71 User Manual
ProMaster Universal Memory Card Multi Reader Universal Memory Card Multi Reader User Manual
Polk Audio db501 User Manual
Pioneer LECTEUR BDP 120 User Manual
Panasonic AVCCAM AG HMC150P User Manual
Mackie ACTIVE SUBWOOFER SYSTEM SRS1500 User Manual
KitchenAid KSB580 User Manual
JVC KD AR7500 User Manual
JVC GZ MG20AS User Manual