P B 7 0 0
P B 10 0 0
P B 110 0
P B 15 0 0
P B 2 6 0 0
P B 12 0 0
P B 17 0 0
P B 2 2 0 0
P B 2 7 0 0
USER'S MANUAL
ta b le o f c o n te n ts
1
g e n e ra l fe a tu re s
2
g e n e ra l fe a tu re s
3
g e n e ra l fe a tu re s
4
2 c h a m p P B 7 0 0 • P B 10 0 0 • P B 110 0 • P B 15 0 0 • P B 2 6 0 0
power LED
protection LED
p b 7 0 0
p b 10 0 0
p b 110 0
p b 15 0 0
p b 2 6 0 0
Remote Bass Boost
high pass frequency control
low pass frequency control
high level inputs
low level inputs
input level control
5
bass boost level
crossover mode selector
power terminals
power fuse
speaker connections
fe a tu re s a n d s p e c ific a tio n s
2 c h a m p P B 7 0 0 • P B 10 0 0 • P B 110 0
crossover mode selector
input level control
when used with normal, full range systems, set this switch to “FULL.” If
you wish to use the internal crossover to power a driver of specific frequency
range, use the “LOWPASS” or “HIGHPASS” settings.
output power @ 14.4v DC, 1KHz
RMS Power @ 4 Ohms
RMS Power @ 2 Ohms
Maximum Power Output 350 Watts x 2 500 Watts x 2 550 Watts x 2
40 Watts x 2 50 Watts x 2 50 Watts x 2
60 Watts x 2 70 Watts x 2 75 Watts x 2
use this control to match the outputs of your head unit to the amplifier.
Starting with your head unit set at about the 2 o’clock position, increase
the amp level control until distortion begins to occur, and reduce slightly
from this point.
frequency response
input impedance
15 Hz-30 KHz
low pass frequency control
high pass frequency control
when the crossover selector switch is in “low pass” mode, this control
sets the upper frequency limit for audio program sent to the speakers.
low level inputs
high level inputs
10K Ohms
100 Ohms
when the crossover selector switch is in “high pass” mode, this control
sets the lower frequency limit for audio program sent to the speakers.
input sensitivity
6
Remote Bass Boost
Plug in the Remote Bass Boost Control wire in here.
low level inputs
high level inputs
250mV
2.5V
bass boost level control
this control permits adjustment of the bass level up to an increase of
approximately 18 dB.
power supply voltage
14.4V DC Neg. Ground (10.5-16V)
low level inputs
high level inputs
this amp features gold-plated RCA input jacks for high impedance input.
Use these with car stereo output which uses RCA-type connector cables.
matching speaker impedance
stereo mode
bridged mode
2-4 Ohms
4-8 Ohms
if your car stereo lacks RCA-type output jacks, you may connect speaker
output leads to these input connectors.
power LED
protection LED
power fuse
this indicator is illuminated when power is applied.
15A
15A
15A
maximum current draw
this indicator is illuminated when built-in protection circuitry is activated.
dimensions (W x H x L)
mm
inches
271 x 60 x 175
10.7 x 2.4 x 6.9
271 x 60 x 190 271 x 60 x 210
10.7 x 2.4 x 7.5 10.7 x 2.4 x 8.3
the fuse protects the amplifier and your car’s electrical system from short
circuit conditions.
power terminals
use these connectors to deliver power, ground and remote turn-on control
to the amplifier.
speaker connections
these terminals are 14K gold plated to guarantee high conductivity and
minimum signal loss.
fe a tu re s a n d s p e c ific a tio n s
2 c h a m p P B 15 0 0 • P B 2 6 0 0
crossover mode selectors when used with normal, full range systems, set these switches to “FULL.”
output power @ 14.4v DC, 1KHz
If you wish to use the internal crossovers to power a driver of specific
frequency range, use the “LOWPASS” or “HIGHPASS” settings.
RMS Power @ 4 Ohms
RMS Power @ 2 Ohms
Maximum Power Output
65 Watts x 2
125 Watts x 2
750 Watts x 2
90 Watts x 2
150 Watts x 2
1300 Watts x 2
input level controls use these controls to match the outputs of your head unit to the amplifier.
Starting with your head unit set at about the 2 o’clock position, increase
the amp level controls until distortion begins to occur, and reduce slightly
from this point.
frequency response
input impedance
15 Hz-30 KHz
low pass frequency controls when one or both of the crossover selector switches is in “low pass”
mode, one can set the upper frequency limit for audio program sent to
the speakers.
low level inputs
high level inputs
10K Ohms
100 Ohms
high pass frequency controls when the one or both of crossover selector switch is in “high pass” mode,
one can set the lower frequency limit for audio program sent to the
speakers.
input sensitivity
low level inputs
high level inputs
7
250mV
2.5V
CH3/4 Remote Bass Boost
Plug in the Remote Bass Boost Control wire in here.
bass boost level controls this control permits adjustment of the bass level up to an increase of
power supply voltage
14.4V DC Neg. Ground (10.5-16V)
approximately 18 dB in either or both pairs of channels.
matching speaker impedance
low level inputs this amp features gold-plated RCA input jacks for high impedance input.
2-4 Ohms
4-8 Ohms
Use these with car stereo output which uses RCA-type connector cables.
stereo mode
bridged mode
high level inputs if your car stereo lacks RCA-type output jacks, you may connect speaker
output leads to these input connectors.
maximum current draw
20 A
30 A
power LED this indicator is illuminated when power is applied.
dimensions (W x H x L)
protection LED this indicator is illuminated when built-in protection circuitry is activated.
mm
inches
271 x 60 x 250
10.7 x 2.4 x 9.8
271 x 60 x 300
10.7 x 2.4 x 11.8
power fuse the fuse protects the amplifier and your car’s electrical system from short
circuit conditions.
power terminals use these connectors to deliver power, ground and remote turn-on control
to the amplifier.
speaker connections these terminals are 14K gold plated to guarantee high conductivity and
minimum signal loss.
fe a tu re s a n d c o n tro ls
4 c h a m p P B 12 0 0 • P B 17 0 0 • P B 2 2 0 0 • P B 2 7 0 0
Remote Bass Boost
ch 3/4 input level control
ch 3/4 high level inputs
ch 1/2 input level control
ch 1/2 high level inputs
p b 12 0 0
p b 17 0 0
p b 2 2 0 0
p b 2 7 0 0
ch 3/4 low level inputs
ch 1/2 low level inputs
ch 3/4 crossover mode selector switch
ch 3/4 bass boost level control
ch 3/4 low pass frequency control
ch 3/4 high pass frequency control
ch 1/2 crossover mode selector switch 8
ch 1/2 bass boost level control
ch 1/2 low pass frequency control
ch 1/2 high pass frequency control
protection LED
power LED
power terminals
power fuse
speaker connections
fe a tu re s a n d s p e c ific a tio n s
4 c h a m p P B 12 0 0 • P B 17 0 0
9
fe a tu re s a n d s p e c ific a tio n s
4 c h a m p P B 2 2 0 0 • P B 2 7 0 0
10
e le c tric a l c o n n e c tio n s
2 c h a m p P B 7 0 0 • P B 10 0 0 • P B 110 0
P B 15 0 0 • P B 2 6 0 0
p b 7 0 0
p b 10 0 0
p b 110 0
p b 15 0 0
p b 2 6 0 0
11
12V battery
head unit
to remote turn-on
+12V
e le c tric a l c o n n e c tio n s
4 c h a m p P B 12 0 0 • P B 17 0 0 • P B 2 2 0 0 • P B 2 7 0 0
p b 12 0 0
p b 17 0 0
p b 2 2 0 0
p b 2 7 0 0
12
12V battery
head unit
to remote turn-on
+12V
s te re o in p u t c o n n e c tio n s
2 c h a m p P B 7 0 0 • P B 10 0 0 • P B 110 0
P B 15 0 0 • P B 2 6 0 0
using low level inputs
using high level inputs
p b 7 0 0
p b 10 0 0
p b 110 0
p b 15 0 0
p b 2 6 0 0
head unit
L/R Audio
Outputs
13
Y Adaptors
PLEASE NOTE! If using high level
inputs, do not use the low level RCA
inputs at the same time!
head unit
L
L
R
R
from speaker terminals
m o n o in p u t c o n n e c tio n s
2 c h a m p P B 7 0 0 • P B 10 0 0 • P B 110 0
P B 15 0 0 • P B 2 6 0 0
using low level inputs
p b 7 0 0
p b 10 0 0
p b 110 0
p b 15 0 0
p b 2 6 0 0
head unit
14
To a second amplifier
Y Adaptors
PLEASE NOTE! If using high level
inputs, do not use the low level RCA
inputs at the same time!
using high level inputs
head unit
To a second amplifier
L
L
R
R
wiring harness
wiring harness
from speaker terminals
S te re o in p u t c o n n e c tio n s
4 c h a m p P B 12 0 0 • P B 17 0 0 • P B 2 2 0 0 • P B 2 7 0 0
4 CH Stereo input connections using low level inputs
p b 12 0 0
p b 17 0 0
p b 2 2 0 0
p b 2 7 0 0
head unit
L/R FRONT
Audio Outputs
15
L/R REAR
Audio Outputs
2 CH Stereo input connections using low level inputs
R
L
Y adaptors
h ig h le v e l S te re o in p u t c o n n e c tio n s
4 c h a m p P B 12 0 0 • P B 17 0 0 • P B 2 2 0 0 • P B 2 7 0 0
4 CH floating ground connections
4 CH floating ground connections
p b 12 0 0
p b 17 0 0
p b 2 2 0 0
p b 2 7 0 0
16
4 CH harness wiring for common ground connections
CH 3/4
CH 1/2
REAR
L
R
L
R
FRONT
ORANGE
ORANGE
REAR
L
R
L
R FRONT
BLACK
BLACK
ORANGE
BLACK
BLACK
ORANGE
ORANGE
ORANGE
from speaker terminals
BLACK
BLACK
ORANGE
BLACK
BLACK
PLEASE NOTE! If using high level inputs,
do not use the low level RCA inputs at the
same time!
ORANGE
from speaker terminals
m o n o in p u t c o n n e c tio n s
4 c h a m p P B 12 0 0 • P B 17 0 0 • P B 2 2 0 0 • P B 2 7 0 0
4 CH mono input connections using low level inputs
p b 12 0 0
p b 17 0 0
p b 2 2 0 0
p b 2 7 0 0
head unit
LEFT FRONT Audio Outputs
LEFT REAR Audio Outputs
17
RIGHT FRONT Audio Outputs
RIGHT REAR Audio Outputs
2 CH mono input connections using low level inputs
L
R
Y adaptors
h ig h le v e l m o n o in p u t c o n n e c tio n s
4 c h a m p P B 12 0 0 • P B 17 0 0 • P B 2 2 0 0 • P B 2 7 0 0
4 CH floating ground connections
p b 12 0 0
p b 17 0 0
p b 2 2 0 0
p b 2 7 0 0
4 CH harness wiring
for common ground connections
18
R
L
ORANGE
BLACK
ORANGE
BLACK
BLACK
BLACK
ORANGE
ORANGE
from speaker terminals
PLEASE NOTE! If using high level inputs, do
not use the low level RCA inputs at the same
time!
s p e a k e r c o n n e c tio n s
2 c h a m p P B 7 0 0 • P B 10 0 0 • P B 110 0
P B 15 0 0 • P B 2 6 0 0
Stereo Output Mode
p b 7 0 0
p b 10 0 0
p b 110 0
p b 15 0 0
p b 2 6 0 0
19
Bridged Mono Output Mode
LEFT speaker
RIGHT speaker
MINIMUM
SPEAKER
IMPEDANCE
4 OHMS!
speaker
s p e a k e r c o n n e c tio n s
4 c h a m p P B 12 0 0 • P B 17 0 0 • P B 2 2 0 0 • P B 2 7 0 0
4 CH Output Mode
p b 12 0 0
p b 17 0 0
p b 2 2 0 0
p b 2 7 0 0
20
L
R
FRONT speakers
REAR speakers
R
L
Bridged Dual Mono Output Mode
MINIMUM
SPEAKER
IMPEDANCE
4 OHMS!
speakers
L
R
s p e a k e r c o n n e c tio n s
4 c h a m p P B 12 0 0 • P B 17 0 0 • P B 2 2 0 0 • P B 2 7 0 0
2 CH Stereo Output Mode with Subwoofer Output
p b 12 0 0
p b 17 0 0
p b 2 2 0 0
p b 2 7 0 0
21
MINIMUM
SPEAKER
IMPEDANCE
4 OHMS!
R
L
SPEAKERS
SUBWOOFER
m o u n tin g a n d in s ta lla tio n
22
p ro te c tio n
c irc u itry
tro u b le s h o o tin g
23
p re c a u tio n s
n o te s
24
15
|
Proctor Silex 840096000 User Manual
PB Heat MI User Manual
Panasonic NV GS250GN User Manual
Palm Series 3 User Manual
Nikon Camera Lens AF Nikkor 50mm f User Manual
Maretron MBB100 User Manual
Lanier CYAN TONER CARTRIDGE 480 0279 User Manual
Kenwood KRC 579R User Manual
Kenwood Car Stereo System KRC 411 User Manual
JVC KV MH6500 User Manual