Planar Systems Car Video System PT1745R User Manual

PT1745R / PT1745S / PT1745RPF  
Touch Screen LCD Monitor  
USER’S GUIDE  
Table of Contents  
Usage Notice  
Precautions............................................................................................................................. 1  
Introduction  
About PT1745R/PT1745S/PT1745RPF ................................................................................ 2  
Touch Screen for PT1745R/PT1745S/PT1745RPF ........................................................ 2  
Package Overview ...................................................................................................... 3  
Installation  
Product Overview ........................................................................................................ 4  
Front View............................................................................................................... 4  
Bottom View ........................................................................................................... 4  
Start Your Installation .................................................................................................. 5  
Connecting the Display (Figure 7.1)............................................................................. 6  
(Figure 7.1) ............................................................................................................. 7  
Kensington Security Slot.............................................................................................. 8  
VESA Mount Your Monitor ........................................................................................... 9  
Remove the Deskstand...........................................................................................10  
User Controls  
Side Panel Controls....................................................................................................11  
How to Use the OSD Menus .......................................................................................12  
On-Screen Display Menus ..........................................................................................13  
Appendix  
Troubleshooting..........................................................................................................14  
Warning Signal ...........................................................................................................15  
No Signal.................................................................................................................15  
Going to Sleep........................................................................................................15  
Out of Range..........................................................................................................15  
Product Dimensions ...................................................................................................16  
Compatibility Modes ...................................................................................................17  
Touch Screen Driver Installation .................................................................................18  
PT1745R/PT1745S/PT1745RPF Optional Calibration Tool Install ...............................18  
PT1745R/PT1745S/PT1745RPF Install Instructions..................................................19  
Product Registraton and Technical Support ................................................................21  
Usage Notice  
!
!
Warning - To prevent the risk of re or shock hazards, do not expose  
this product to rain or moisture.  
Warning - Please do not open or disassemble the product as this may  
cause electric shock.  
Precautions  
Follow all warnings, precautions and maintenance as recommended in this user’s manual to  
maximize the life of your unit.  
Do:  
• Turn off the product before cleaning.  
Touch screen surface may be cleaned using a soft clean cloth moistened with  
mild window glass commercial cleaners or 50/50 mixture of water and isopropyl  
alcohol.  
• Use a soft cloth moistened with mild detergent to clean the display housing.  
• Use only high quality and safety approved AC/DC adapter.  
• Disconnect the power plug from AC outlet if the product is not going to be used for  
an extended period of time.  
Don’t:  
• Do not touch the LCD Display screen surface with sharp or hard objects.  
• Do not use abrasive cleaners, waxes or solvents for your cleaning.  
• Do not operate the product under the following conditions:  
- Extremely hot, cold or humid environment.  
- Areas susceptible to excessive dust and dirt.  
- Near any appliance generating a strong magnetic eld.  
- In direct sunlight.  
1
Introduction  
About PT1745R/PT1745S/PT1745RPF  
The PT1745R/PT1745S/PT1745RPF is a 17" at panel screen with an active matrix,  
thin-lm transistor (TFT) liquid crystal display (LCD).  
Features include:  
• Direct Analog signal input  
• Active matrix TFT LCD technology  
• 1280 x 1024 SXGA resolution  
• 17" viewable display area  
• 31.47 ~ 80 KHz horizontal scan  
• 56 ~ 75 Hz high refresh rate  
• 0.264mm x 0.264mm pixel pitch  
• Auto adjustment function  
• Multilingual OSD user control  
• Kensington security slot  
• 100 mm VESA mount  
• Removable base for exible mounting solutions.  
• PT1745R/PT1745RPF - 5-wire resistive touch screen with dual RS-232 Serial/USB  
controller.  
• PT1745S - SAW touch screen with dual RS-232 Serial/USB controller  
• Build-in audio-1W x 2  
Touch Screen for PT1745R/PT1745RPF  
• Analog 5-wire resistive touch screen for nger and stylus input  
• Surface: Anti-glare treatment  
• Interface: Dual RS-232 Serial/USB controller  
• PT1745R Transmittance: 82%±5%  
• PT1745RPF Transmittance: 50%±5% (with Privacy Filter)  
®
• Driver: Windows 7, VISTA, XP, 2000, ME, 98, NT 4.0, CE, XP Embedded, Linux,  
®
Apple Mac OS  
Touch Screen for PT1745S  
• Surface Acoustic Wave (SAW) touch screen for nger and stylus input  
• Surface: Anti-glare treatment  
• Interface: Dual RS-232 Serial/USB controller  
• Transmittance: 92±5%  
®
• Driver: Windows 7, VISTA, XP, 2000, ME, 98, NT4.0, CE, XP Embedded, Linux,  
®
Apple Mac OS  
2
Package Overview  
LCD Display  
VGA Signal Cable  
Power Cord  
Audio-in Cable  
RS-232 Cable  
USB Cable ( A to B)  
xxxxxxxxx /  
xxxxxxxxx  
xxxxxxxxx  
USER’S GUIDE  
www  
.planartouch.com  
Touch Screen Driver  
Installation CD-ROM  
Landing Strip  
User’s Guide  
Screw  
3
Installation  
Product Overview  
• Front View  
• Bottom View  
AUDIO  
RS-232  
USB  
AC IN  
VGA  
POWER SWITCH  
4
Start Your Installation  
Please follow these instructions so that you can hookup the cables to associated connector.  
1. Lay the LCD at on an even surface.  
2. Move the stand into position as seen in the step 2 diagram.  
3. Remove the cable cover as seen in the step 3 diagram.  
4. Connect the cables to the appropriate connectors as seen in the step 4 diagram. Use  
step 4-1 diagram if using the RS-232 serial connector. Use the step 4-2 diagram if using  
the USB connector.  
5. Position all cables under the cover lip as seen in the step 5 diagram.  
6. Re-attach the cable cover . Remove the screw (CBM M3x6) from the accessory box, and  
insert the screw into the cable cover and monitor as seen in the step 5 diagram.  
Step 2  
Step 3  
Step 4-1  
Step 4-2  
Power  
Power  
USB  
Audio (Option)  
RS-232  
Audio (Option)  
VGA  
VGA  
Step 5  
5
Connecting the Display (Figure 7.1)  
To setup this display, please refer to the following gure and procedures.  
1. Be sure all equipment is turned off.  
2. Connect the AC power cord to the power connector on the monitor and the other end  
into an electrical outlet (7.1).  
3. Connect the D-SUB cable from the display's VGA input connector to the D-SUB  
connector of your host computer and tighten the screws (7.1).  
4. Connector the audio-in cable from the audio input port of your display to the audio out  
port of your computer (7.1).  
5. Connect the RS-232 or USB cable from the RS-232 or USB port of your display to the  
RS-232 port or USB port (7.1) of your computer.  
6. Congure the touch screen. Refer to the “Touch Screen Driver Installation” section on  
page 18.  
7. Once the touch screen is congured, the monitor is ready for use.  
!
Notice!  
To ensure the LCD display works well with your computer, please congure the  
display mode of your graphics card to make it less than or equal to 1280 x 1024  
resolution and make sure the timing of the display mode is compatible with the LCD  
display.  
We have listed the compatible “Video Modes” of your LCD display in the appendix  
(on page 17) for your reference.  
6
(Figure 7.1)  
7
Kensington Security Slot  
The monitor can be secured to your desk or any other xed object with Kensington lock  
security products. The Kensington lock is not included.  
8
VESA Mount Your Monitor  
This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard  
which denes a physical mounting interface for at panel monitors, and corresponding with  
the standards of at panel monitor mounting devices, such as wall and table arms. The VESA  
mounting interface is located on the back of your monitor.  
To mount the monitor on an UL-listed certied swing arm or other mounting xture, follow the  
instructions included with the mounting xture to be used.  
Slots (x4)  
100.0 mm  
VESA  
Mounting  
Interface  
!
Warning!  
Please select the proper screws!  
The distance between the back cover surface and the bottom of the screw hole  
is 11 mm. Please use four M4 screws diameter with proper length to mount your  
monitor.  
Please note: the mounting stand must be able to support at least 11 lbs ( 5Kg).  
9
Remove the Deskstand  
Remove 4 screws and then remove hinge.  
10  
User Controls  
Side Panel Controls  
Icon  
key Name  
Menu  
Up  
Down  
Enter  
Power  
OSD  
Menu off status  
Key  
Menu on status  
Menu appear  
Brightness  
Mute  
Menu disappear/ return to main item  
Main item select up/ Adjust up  
Main item select down/ Adjust down  
Enter/Select sub-item function  
Power On/Off  
11  
How to Use the OSD Menus  
Icon  
Key Name  
Menu  
Up  
Down  
Enter  
Power  
1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or “Down” button  
to select among the six functions in the main menu.  
2. Choose the adjustment items by pressing the “Enter ” button.  
3. Adjust the value of the adjustment items by pressing the “Up” or “Down” button.  
4. With the OSD menu on screen, press “ Menu” button to return main menu or exit OSD.  
5. The OSD menu will automatically close, if you have left it idle for a pre-set time.  
6. To Lock the OSD / Power menu buttons, please follow the instructions below.  
(Please note: the monitor has to be turned ON with a valid signal pre-set)  
(a.) Press “Menu” key , the OSD menu will pops upon display.  
(b.) Press and hold the “Menu” key again with the OSD menu on the screen, the OSD  
menu will disappear. Then press the “Power” key 1 time while the menu key is still  
being pressed. The “Lock/Unlock” menu will appear for 3 seconds.  
(c.) Use the “Enter” key to select OSD or Power setting then set at “Lock” by pushing the  
“UP” or “Down” button.  
(d.) When the “UP” or “Down” button is released, the previous setting will be saved and  
exit the “Lock/Unlock” menu automatically.  
7. To Unlock the OSD / Power menu buttons, please follow the instructions below.  
(Please note: the monitor has to be turned ON with a valid signal pre-set)  
(a.) Press and hold the “Menu” key then press the “Power” key simultaneously, the “Lock/  
Unlock” menu will appear for 3 seconds.  
(b.) Use the “Enter” key to select OSD or Power setting then set at “Unlock” by pushing the  
“UP” or “Down” button.  
(c.) When the “UP” or “Down” button is released, the previous setting will be saved and exit  
the “Lock/Unlock” menu automatically.  
Please note:  
a. When the OSD Lock function is selected, this indicates that all the buttons except “power”  
button are now disabled.  
b. When the Power Lock function is selected, this indicates that the power key is disabled;  
user can not to turn off the monitor by “Power” key.  
12  
On-Screen Display Menus  
Main OSD Menu:  
ITEM  
CONTENT  
Contrast  
The monitor luminance level control.  
The monitor backlight level control.  
Brightness  
Auto Adjust  
Left/Right  
Up/Down  
Fine-tune the image to full screen automatically.  
Moving screen image horizontal position to left or right.  
Moving screen image vertical position to up or down.  
Horizontal size The screen image horizontal dot clock adjustment.  
Fine The screen image pixel phase adjustment.  
OSD Left/Right Moving OSD menu horizontal position to left or right.  
OSD Up/Down  
OSD Time out  
Moving OSD menu vertical position to up or down.  
OSD auto-disappear time selection.  
OSD menu language selection. ( English, French, Japanese, Deutsch,  
OSD Language  
Spanish, Italian, Traditional Chinese and Simplied Chinese)  
Factory Reset  
RGB  
Factory default value restored.  
Color temperature selection. (9300K, 6500K, 5500K, 7500K, User)  
Audio volume adjustment.  
Volume  
Mute  
Audio On/Off control.  
13  
Appendix  
Troubleshooting  
If you are experiencing trouble with the LCD display, refer to the following. If the problem  
persists, please contact your local dealer or our service center.  
Problem: No image appears on screen.  
Check that all the I/O and power connectors are correctly and well connected  
described in the "Installation" section.  
Make sure the pins of the connectors are not crooked or broken.  
Problem: Partial Image or incorrectly displayed image.  
Check to see if the resolution of your computer is higher than that of the LCD  
display.  
Recongure the resolution of your computer to make it less than or equal to  
1280 x 1024.  
Problem: Image has vertical ickering line bars.  
Use "Fine" to make an adjustment.  
Check and recongure the display mode of the vertical refresh rate of your graphic  
card to make it compatible with the LCD display.  
Problem: Image is unstable and ickering  
Use "Horizontal size" to make an adjustment.  
Problem: Image is scrolling  
Check and make sure the VGA signal cable (or adapter) is securely connected.  
Check and recongure the display mode of the vertical refresh rate of your graphics  
card to make it compatible with the LCD display.  
Problem: Vague image (characters and graphics)  
Use "Fine" to make an adjustment. If this problem still exists,  
use "Horizontal size" to make an adjustment.  
14  
Warning Signal  
If you see warning messages on your LCD screen, this means that the LCD display cannot  
receive a clean signal from the computer graphics card.  
Below are the three kinds of Warning Signal. Please check the cable connections or contact  
your local dealer or Planar for more information.  
No Signal  
This message means that the LCD display has been powered on but it cannot receive any  
signal from the computer graphics card. Check all the power switches, power cables, and  
VGA signal cable.  
Going to Sleep  
The LCD display is under the power saving mode. In addition, the LCD display will enter  
power saving mode when experiencing a sudden signal disconnecting problem.  
The monitor can be activated by pressing any key on the keyboard, triggering the mouse or  
touching the screen.  
Out of Range  
This message means that the signal of the computer graphic card is not compatible with the  
LCD display. When the signal is not included in the “Video Modes” list we have listed in the  
Appendices of this manual, the LCD monitor will display this message.  
15  
Product Dimensions  
386.8 mm  
Front View  
67.0 mm  
Side View  
222.5 mm  
Top View  
16  
Compatibility Modes  
Mode  
Resolution  
H-Frequency (KHz)  
V-Frequency (Hz)  
IBM VGA  
720 x 400  
31.47  
70  
IBM VGA  
VESA VGA  
VESA VGA  
VESA SVGA  
VESA SVGA  
VESA SVGA  
VESA SVGA  
VESA XGA  
VESA XGA  
VESA XGA  
VESA SXGA  
VESA SXGA  
VESA SXGA  
VESA SXGA  
Apple Mac II  
Apple Mac  
640 x 480  
640 x 480  
640 x 480  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
1024 x 768  
1024 x 768  
1024 x 768  
1280 x 1024  
1280 x 1024  
1280 x 960  
1152 x 864  
640 x 480  
832 x 624  
31.47  
37.86  
37.50  
35.16  
37.88  
48.08  
46.88  
48.36  
56.48  
60.02  
64.00  
80.00  
60.00  
67.50  
35.00  
49.72  
60  
72  
75  
56  
60  
72  
75  
60  
70  
75  
60  
75  
60  
75  
66  
75  
17  
Touch Screen Driver Installation  
The PT1745R/PT1745S/PT1745RPF is available with both RS232 and USB connections. The  
®
touch driver is located on the enclosed CD-ROM for these operating systems: Windows 7,  
®
VISTA, XP, 2000, ME, 98, NT 4.0, CE, XP Embedded, Linux, Apple Mac OS.  
Please Note: The PT1745R/PT1745S/PT1745RPF is Microsoft® Windows® HID (Human In-  
terface Device) compatible if you use the USB touch screen interface. No additional software  
driver is required for general operation of the touch screen. A calibration tool can be installed  
for improved touch position accuracy. See “Optional Calibration Tool Install” section for more  
information.  
PT1745R/PT1745S/PT1745RPF Optional Calibration Tool  
Install  
If you would like to use the Optional Calibration Tool, follow the instructions below. Please  
®
note: the calibration tool supports Windows 7, VISTA, XP, XP Embedded, 2000, 98 and ME  
operating systems via USB only.  
1. Open the CD-ROM.  
2. Select the monitor size and then model name.  
3. Click on the “Load Utility” button that appears to the right of the model name.  
4. The HID calibration tool will automatically open. From here the user can choose to do  
the following:  
a. 4 Points Calibration  
b. 9 Points Linearization  
c. 25 Points Linearization  
d. Clear  
e. Draw Test  
f. Advanced. In the Advanced settings area the user may do the following:  
i.  
Adjust the Double Click Area.  
ii. Enable auto right click and adjust the auto right click time.  
iii. Choose to be either in the HID Mouse Mode or HID Digitizer Mode (Windows®  
Vista only).  
iv. Simply click the “Apply” button once the settings are nalized.  
18  
PT1745R/PT1745S/PT1745RPF Install Instructions  
®
If you are using a PC running Windows 7, VISTA, XP, 2000, ME, 98,  
NT4.0, follow the instructions below:  
1. Power on the PC.  
2. Be sure the USB or the RS-232 Serial cable is connected from the PC to the LCD  
display.  
3. Open the CD-ROM.  
4. Follow the step-by-step instructions as shown on the pop-up windows.  
®
If you are using a PC running Windows XP Embedded, follow the  
instructions below:  
Express:  
1. Power on the computer.  
2. Make sure that the RS232 or USB cable is connected to the computer.  
3. Be sure that your EWF is disabled. If your EWF is enabled, please disable the EWF by  
using the EWF Manager command.  
4. Once the EWF is disabled click on the XP driver on the CD-ROM and follow the  
step-by-step instructions as shown on the pop-up windows.  
Custom:  
1. Power on the computer.  
2. Make sure that the RS232 or USB cable is connected to the computer.  
3. Follow the step-by-step instructions found in the zipped le on the CD-ROM.  
19  
®
If you are using a PC running Windows CE, follow the instructions  
below:  
1. Power on the computer.  
2. Make sure that the RS232 or USB cable is connected to the computer.  
3. Using Platform Builder, build an image le by following the step-by-step instructions  
found in the zipped le on the CD-ROM.  
®
If you are using a PC running Linux or Apple Mac OS, follow the  
instructions below:  
1. Power on the computer.  
2. Make sure that the RS232 or USB cable is connected to the computer.  
3. Follow the step-by-step instructions found in the zipped le on the CD-ROM.  
When changing the Touch Interface (RS-232 or USB), please follow  
instructions below:  
1. Uninstall the touch driver.  
2. Re-start the computer.  
3. Remove the original Touch Interface (RS-232 or USB).  
4. Connect the computer to the Touch Interface (RS-232 or USB) that you would like to use.  
5. Load the Touch Driver CD, then follow the step-by-step instructions as show on monitor.  
PLEASE NOTE!  
Don’t plug in both the RS-232 and USB cables!  
Doing so may cause a driver conict, making your touch screen inoperable.  
20  
Product Registration and Technical Support  
Register Your Planar Products Today  
Thank you for choosing Planar. To assure you receive all the benets of your Planar product  
and services, register your Planar product today. Visit our website to register your product at  
Cables, Replacement Lamps, Accessories  
To nd cables, replacement lamps and accessories for your Planar projector, LCD monitor,  
touch screen or other Planar products visit our online store at www.PlanarOnline.com or  
nd other stores who carry Planar products at http://www.planar.com/howtobuy.  
Technical Support  
Visit Planar at http://www.planar.com/support for product registration, operations manuals,  
touch screen drivers, warranty information and access to Planar’s Technical Library for online  
troubleshooting.  
To speak with Planar Customer Support please have your model and serial number available  
and dial:  
Planar Support  
Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the US.  
Hours: 24 hours a day, 7 days a week.  
Toll or long distance charges may apply.  
21  
Planar Systems, Inc.  
Customer Service  
1195 NW Compton Drive  
Beaverton, OR 97006-1992  
Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the United States.  
Hours: 24 hours a day, 7 days a week  
© 2011 Planar Systems, Inc. 4/11 Planar is a registered trademark of Planar Systems, Inc.  
Other brands and names are the property of their respective owners.  
Technical information in this document is subject to change without notice.  
020-1021-00D  
820470035104  

PYLE Audio PLTDN70 User Manual
Plantronics Bluetooth Headset M165 User Manual
Philips CAM110 User Manual
Olympus m_robe MR 100 User Manual
Nostalgia Electrics Retro RSM 650 User Manual
Nokia Bluetooth Stereo Headset BH 221 User Manual
Nikon Digital Cameras User Manual
Lanzar Car Audio Lanzar Vibe VIBE251 User Manual
KitchenAid KFPW760COB0 User Manual
JVC XL MV558GD User Manual