Pioneer AVH P3400BH User Manual

Owners Manual  
DVD RDS AV RECEIVER  
AVH-P4400BH  
AVH-P3400BH  
AVH-P2400BT  
AVH-P1400DVD  
English  
Contents  
3
En  
Section  
Precautions  
01  
IMPORTANT SAFEGUARDS  
Please read all of these instructions regarding  
your display and retain them for future refer-  
ence.  
WARNING  
Do not attempt to install or service your dis-  
play by yourself. Installation or servicing of  
the display by persons without training and  
experience in electronic equipment and auto-  
motive accessories may be dangerous and  
could expose you to the risk of electric shock  
or other hazards.  
1
Read this manual fully and carefully be-  
fore operating your display.  
2
Keep this manual handy as a reference for  
operating procedures and safety informa-  
tion.  
3
4
5
Pay close attention to all warnings in this  
manual and follow the instructions care-  
fully.  
Do not allow other persons to use this sys-  
tem until they have read and understood  
the operating instructions.  
To ensure safe driving  
WARNING  
!
LIGHT GREEN LEAD AT POWER CON-  
NECTOR IS DESIGNED TO DETECT  
PARKED STATUS AND MUST BE CON-  
NECTED TO THE POWER SUPPLY SIDE  
OF THE PARKING BRAKE SWITCH. IM-  
PROPER CONNECTION OR USE OF  
THIS LEAD MAY VIOLATE APPLICABLE  
LAW AND MAY RESULT IN SERIOUS IN-  
JURY OR DAMAGE.  
Do not install the display where it may (i)  
obstruct the drivers vision, (ii) impair the  
performance of any of the vehicles oper-  
ating systems or safety features, includ-  
ing air bags, hazard lamp buttons or (iii)  
impair the drivers ability to safely oper-  
ate the vehicle.  
Do not operate this display if doing so in  
any way will divert your attention from  
the safe operation of your vehicle. Always  
observe safe driving rules and follow all  
existing traffic regulations. If you experi-  
ence difficulty in operating the system or  
reading the display, park your vehicle in a  
safe location and make necessary adjust-  
ments.  
Please remember to wear your seat belt at  
all times while operating your vehicle. If  
you are ever in an accident, your injuries  
can be considerably more severe if your  
seat belt is not properly buckled.  
Never use headphones while driving.  
To promote safety, certain functions are  
disabled unless the parking brake is on,  
and the vehicle is not in motion.  
6
!
!
!
To avoid the risk of damage and injury and the  
potential violation of applicable laws, this unit  
is not for use with a video screen that is visible  
to the driver.  
To avoid the risk of accident and the potential  
violation of applicable laws, no viewing of  
front seat video should ever occur while the  
vehicle is being driven.  
In some countries or states the viewing of  
images on a display inside a vehicle even by  
persons other than the driver may be illegal.  
Where such regulations apply, they must be  
obeyed and this units DVD features should  
not be used.  
7
8
9
When you attempt to watch a video image  
while driving, the warning Viewing of front  
seat video source while driving is strictly  
prohibited.will appear on the front display.  
To watch a video image on the front display,  
park your vehicle in a safe place and apply the  
parking brake.  
10 Never set the volume of your display so  
high that you cannot hear outside traffic  
and emergency vehicles.  
5
En  
 
Section  
01  
Precautions  
backing up. Do not use for entertainment pur-  
poses.  
Parking brake interlock  
Certain functions (Video viewing and certain  
touch panel keys) offered by this unit could be  
dangerous and/or unlawful if used while driv-  
ing. To prevent such functions from being  
used while the vehicle is in motion, there is an  
interlock system that senses when the parking  
brake is set. If you attempt to use the functions  
described above while driving, they will be-  
come disabled until you stop the vehicle in a  
safe place, and (1) apply the parking brake, (2)  
release the parking brake, and then (3) apply  
the parking brake again. Please keep the  
brake pedal pushed down before releasing the  
parking brake.  
!
Please note that the edges of the rear view  
camera images may differ slightly according  
to whether full screen images are displayed  
when backing up, and whether the images are  
used for checking the rear when the vehicle is  
moving forward.  
To avoid battery exhaustion  
Keep the vehicle engine running when using  
this unit to avoid draining the battery power.  
!
When no power is supplied to this unit,  
such as when the vehicle battery is being  
replaced, the microcomputer of this unit re-  
turns to its initial condition. We recom-  
mend that you transcribe the audio  
adjustment data.  
When using a display  
connected to V OUT  
This units V OUT is for connection of a dis-  
play to enable passengers in the rear seats to  
watch the DVD or Video CD.  
WARNING  
Do not use with vehicles that do not feature an  
ACC position.  
WARNING  
NEVER install the rear display in a location  
where the driver can watch a DVD while driving.  
When using the rear view camera  
With an optional rear view camera, this unit  
can be used as an aid to keep an eye on trai-  
lers, or when backing into a tight parking spot.  
WARNING  
SCREEN IMAGE MAY APPEAR RE-  
VERSED.  
USE INPUT ONLY FOR REVERSE OR  
MIRROR IMAGE REAR VIEW CAMERA.  
OTHER USE MAY RESULT IN INJURY  
OR DAMAGE.  
!
!
CAUTION  
!
The rear view camera function is to be used  
as an aid to keep an eye on trailers, or while  
6
En  
 
Section  
Before you start  
02  
Information to User  
FCC ID: AJDK044  
MODEL NO.: AVH-P4400BH/AVH-P3400BH/  
AVH-P2400BT  
Alteration or modifications carried out without  
appropriate authorization may invalidate the  
users right to operate the equipment.  
IC: 775E-K044  
This device complies with Part 15 of FCC Rules  
and Industry Canada licence-exempt RSS stan-  
dard(s). Operation is subject to the following  
two conditions: (1) this device may not cause  
interference, and (2) this device must accept  
any interference, including interference that  
may cause undesired operation of this device.  
This transmitter must not be co-located or op-  
erated in conjunction with any other antenna  
or transmitter.  
Note  
This equipment has been tested and found to  
comply with the limits for a Class B digital de-  
vice, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reason-  
able protection against harmful interference in  
a residential installation. This equipment gen-  
erates, uses and can radiate radio frequency  
energy and, if not installed and used in accor-  
dance with the instructions, may cause harm-  
ful interference to radio communications.  
However, there is no guarantee that interfer-  
ence will not occur in a particular installation.  
If this equipment does cause harmful interfer-  
ence to radio or television reception, which  
can be determined by turning the equipment  
off and on, the user is encouraged to try to cor-  
rect the interference by one or more of the fol-  
lowing measures:  
The antenna for Bluetooth cannot be removed  
(or replaced) by user.  
This equipment complies with FCC/IC radiation  
exposure limits set forth for an uncontrolled  
environment and meets the FCC radio fre-  
quency (RF) Exposure Guidelines in Supple-  
ment C to OET65 and RSS-102 of the IC radio  
frequency (RF) Exposure rules. This equipment  
has very low levels of RF energy that it deemed  
to comply without maximum permissive expo-  
sure evaluation (MPE). But it is desirable that  
it should be installed and operated keeping the  
radiator at least 20 cm or more away from per-  
sons body (excluding extremities: hands,  
wrists, feet and ankles).  
- Reorient or relocate the receiving antenna.  
- Increase the separation between the equip-  
ment and receiver.  
- Connect the equipment into an outlet on a  
circuit different from that to which the receiver  
is connected.  
MODEL NO.: AVH-P1400DVD  
- Consult the dealer or an experienced radio/TV  
technician for help.  
This device complies with Part 15 of the FCC  
Rules. Operation is subject to the following  
two conditions:  
(1) this device may not cause harmful interfer-  
ence, and (2) this device must accept any inter-  
ference received, including interference that  
may cause undesired operation.  
7
En  
 
Section  
02  
Before you start  
defect or other reproductive harm. Wash hands  
after handling.  
The Safety of Your Ears is in  
Your Hands  
Get the most out of your equipment by playing  
it at a safe levela level that lets the sound  
come through clearly without annoying blar-  
ing or distortion and, most importantly, with-  
out affecting your sensitive hearing. Sound  
can be deceiving. Over time, your hearing  
comfort leveladapts to higher volumes of  
sound, so what sounds normalcan actually  
be loud and harmful to your hearing. Guard  
against this by setting your equipment at a  
safe level BEFORE your hearing adapts.  
CAUTION:  
USE OF CONTROL OR ADJUSTMENT OR  
PERFORMANCE OF PROCEDURES  
OTHER THAN THOSE SPECIFIED HEREIN  
MAY RESULT IN HAZARDOUS RADIATION  
EXPOSURE.  
CAUTION:  
THE USE OF OPTICAL INSTRUMENTS  
WITH THIS PRODUCT WILL INCREASE  
EYE HAZARD.  
ESTABLISH A SAFE LEVEL:  
CAUTION  
!
!
Set your volume control at a low setting.  
Slowly increase the sound until you can  
hear it comfortably and clearly, without dis-  
tortion.  
!
Do not allow this unit to come into contact  
with liquids. Electrical shock could result.  
Also, damage to this unit, smoke, and over-  
heating could result from contact with liquids.  
Keep this manual handy for future reference.  
Always keep the volume low enough to hear  
outside sounds.  
Avoid exposure to moisture.  
If the battery is disconnected or discharged,  
any preset memory will be erased.  
!
Once you have established a comfortable  
sound level, set the dial and leave it there.  
!
!
BE SURE TO OBSERVE THE FOLLOWING  
GUIDELINES:  
!
!
!
!
!
Do not turn up the volume so high that you  
cant hear whats around you.  
Use caution or temporarily discontinue use  
in potentially hazardous situations.  
Do not use headphones while operating a  
motorized vehicle; the use of headphones  
may create a traffic hazard and is illegal in  
many areas.  
Important (Serial number)  
The serial number is located on the bottom of  
this unit. For your own security and convenience,  
be sure to record this number on the enclosed  
warranty card.  
DVD video disc region numbers  
About this unit  
The tuner frequencies on this unit are allo-  
cated for use in North America. Use in other  
areas may result in poor reception.  
Only DVD video discs with compatible region  
numbers can be played on this player. You can  
find the region number of the player on the  
bottom of this unit and in this manual (refer to  
WARNING  
Handling the cord on this product or cords asso-  
ciated with accessories sold with the product  
may expose you to chemicals listed on proposi-  
tion 65 known to the State of California and other  
governmental entities to cause cancer and birth  
8
En  
 
Section  
Before you start  
02  
About this manual  
U.S.A.  
Pioneer Electronics (USA) Inc.  
CUSTOMER SUPPORT DIVISION  
P.O. Box 1760  
Long Beach, CA 90801-1760  
800-421-1404  
This unit features a number of sophisticated  
functions to ensure superior reception and op-  
eration. All the functions have been designed  
for the easiest possible use, but many are not  
self-explanatory. This operation manual will  
help you benefit fully from this units potential  
and to maximize your listening enjoyment.  
We recommend that you familiarize yourself  
with the functions and their operation by read-  
ing through the manual before you begin  
using this unit. It is especially important that  
you read and observe WARNINGs and CAU-  
TIONs in this manual.  
CANADA  
Pioneer Electronics of Canada, Inc.  
CUSTOMER SATISFACTION DEPARTMENT  
340 Ferrier Street  
Unit 2  
Markham, Ontario L3R 2Z5, Canada  
1-877-283-5901  
905-479-4411  
For warranty information please see the Lim-  
ited Warranty sheet included with this unit.  
Operating environment  
This unit should be used within the tempera-  
ture ranges shown below.  
Operating temperature range: 10 °C to +60 °C  
(14 °F to 140 °F)  
EN300328 ETC test temperature: 20 °C and  
+55 °C (4 °F and 131 °F)  
Visit our website  
Visit us at the following site:  
http://www.pioneerelectronics.com  
in Canada  
http://www.pioneerelectronics.ca  
1
Register your product. We will keep the details  
of your purchase on file to help you refer to  
this information in the event of an insurance  
claim such as loss or theft.  
After-sales service for  
Pioneer products  
Please contact the dealer or distributor from  
where you purchased this unit for after-sales  
service (including warranty conditions) or any  
other information. In case the necessary infor-  
mation is not available, please contact the  
companies listed below:  
Please do not ship your unit to the companies  
at the addresses listed below for repair without  
advance contact.  
2
3
Receive updates on the latest products and  
technologies.  
Download owners manuals, order product  
catalogues, research new products, and  
much more.  
Your feedback is important in our continual ef-  
fort to design and build the most advanced,  
consumer-focused product in the industry.  
Serial number  
4
9
En  
 
Section  
02  
Before you start  
Demo mode  
WARNING  
The feature demo automatically starts when  
you select Off for the source and continues  
while the ignition switch is set to ACC or ON.  
To cancel the feature demo, press and hold  
MUTE. Press and hold MUTE again to restart.  
Operating the feature demo while the car en-  
gine is turned off it may drain the battery  
power.  
!
!
Keep the battery out of the reach of children.  
Should the battery be swallowed, consult a  
doctor immediately.  
Batteries (battery pack or batteries installed)  
must not be exposed to excessive heat such  
as sunshine, fire or the like.  
CAUTION  
!
!
Use one CR2025 (3 V) lithium battery.  
Remove the battery if the remote control is not  
used for a month or longer.  
There is a danger of explosion if the battery is  
incorrectly replaced. Replace only with the  
same or equivalent type.  
Important  
Failure to connect the red lead (ACC) of this unit  
to a terminal coupled with ignition switch on/off  
operations may lead to battery drain.  
!
!
!
!
Do not handle the battery with metallic tools.  
Do not store the battery with metallic objects.  
If the battery leaks, wipe the remote control  
completely clean and install a new battery.  
When disposing of used batteries, comply  
with governmental regulations or environmen-  
tal public institutionsrules that apply in your  
country/area.  
Perchlorate Material special handling may  
apply.  
See www.dtsc.ca.gov/hazardouswaste/  
perchlorate. (Applicable to California, U.S.A.)”  
Adjusting the response  
positions of the touch panels  
(Touch Panel Calibration)  
If you feel that the touch panel keys on the  
screen deviate from the actual positions that  
respond to your touch, adjust the response po-  
sitions of the touch panel. Refer to Adjusting  
!
!
Use and care of the remote  
control  
Installing the battery  
Slide the tray on the back of the remote con-  
trol out and insert the battery with the plus (+)  
and minus () poles aligned properly.  
Using the remote control  
Point the remote control in the direction of the  
front panel to operate.  
!
The remote control may not function prop-  
erly in direct sunlight.  
Important  
!
When using for the first time, pull out the  
film protruding from the tray.  
!
!
Do not store the remote control in high tem-  
peratures or direct sunlight.  
Do not let the remote control fall onto the  
floor, where it may become jammed under the  
brake or accelerator pedal.  
10  
En  
 
Section  
Whats what  
03  
Head unit  
Part  
Part  
(AVH-P4400BH)  
USB port  
HOME  
Displaying the  
home display.  
When connecting,  
open the USB con-  
nector lid.  
4
a
b
AUX input jack  
(3.5 mm stereo/  
video jack)  
Use to connect an  
auxiliary device.  
MODE  
Turning the infor-  
mation display off.  
5
6
c/d (TRK)  
1 2 3 4 5 6 7  
CAUTION  
9
8
!
(AVH-P3400BH/AVH-P2400BT/AVH-  
P1400DVD)  
Use an optional Pioneer USB cable (CD-U50E)  
to connect the USB audio player/USB mem-  
ory as any device connected directly to the  
unit will protrude out from the unit and may  
be dangerous.  
!
!
Do not use unauthorized products.  
(AVH-P3400BH/AVH-P2400BT/AVH-  
P1400DVD)  
Notes  
When the navigation system is connected,  
press MODE to switch to the navigation dis-  
play. Press MODE and hold to turn the display  
off.  
2 6 7 4  
8
Press MODE again to turn the display on.  
For details on how to operate a navigation sys-  
tem from this unit, refer to its operation man-  
ual.  
!
3ab9 5 1  
Part  
Part  
1
2
SRC/OFF  
7
8
h (eject)  
+/(VOLUME/  
VOL)  
Disc loading slot  
Auto EQ micro-  
phone input jack  
Use to connect an  
auto EQ micro-  
phone.  
3
MUTE  
9
11  
En  
 
Section  
03  
Whats what  
Remote control  
Part  
Operation  
Press to pause or re-  
sume playback.  
2
5 1  
f
Press to perform fast  
reverse.  
Press to change the  
fast reverse speed.  
m
n
3
7
Press to perform fast  
forward.  
Press to change the  
fast forward speed.  
1
Press to return to the  
previous track (chap-  
ter).  
6
2
3
4
o
p
3
Press to go to the next  
track (chapter).  
5
Press to stop play-  
back.  
If you resume play-  
back, playback will  
start from the point  
where you stopped.  
Touch the key again to  
stop playback comple-  
tely.  
Part  
Operation  
g
Use to select a menu  
on the DVD menu.  
1
2
Thumb pad  
Press to display the  
PBC (playback con-  
trol) menu during PBC  
playback.  
RETURN  
Press to select the  
next/previous disc/  
folder.  
4
a/b(FOLDER/P.CH)  
Press to recall radio  
station frequencies as-  
signed to preset tun-  
ing keys.  
Press to select the  
tuner band when  
tuner is selected as a  
source. Also used to  
cancel the control  
mode of functions.  
Press to switch be-  
tween modes when  
playing discs and USB  
storage devices with  
compressed audio  
and audio data (CD-  
DA) such as CD-  
5
BAND/ESC  
EXTRA and MIXED-  
MODE CDs.  
12  
En  
 
Section  
Whats what  
03  
Part  
Operation  
Press to change the  
audio language during  
DVD playback.  
AUDIO  
Press to switch audio  
output for Video CD/  
DivX/MPEG-1/  
MPEG-2/MPEG-4.  
6
Press to change the  
subtitle language dur-  
ing DVD/DivX/MPEG-4  
playback.  
SUBTITLE  
Press to change the  
viewing angle during  
DVD playback.  
ANGLE  
Press to display the  
DVD menu during  
DVD playback.  
MENU  
7
Press to return to the  
top menu during DVD  
playback.  
TOP MENU  
13  
En  
Section  
04  
Basic operations  
Touch panel keys  
Basic operations  
Source icon  
HOME display  
Radio  
Selecting a favorite source.  
When the source icon is not  
displayed, it can be displayed  
by touching the screen.  
1
2
3
1
Radio  
4
Radio  
Disc  
AV  
USB  
XM  
Pandora  
Audio  
Displaying the rear view  
image by turning the rear  
view image on.  
SIRIUS  
EXT  
1
AUX  
Rear View  
EXT  
2
When the rear view image is  
displayed, you can switch to  
the source display by touch-  
ing the display. You can oper-  
ate from the source display  
temporarily at this time. If  
you do not perform any op-  
erations within a few sec-  
onds, the display will return  
to the rear view image.  
To turn off the rear view  
image, press HOME to re-  
turn to the HOME display  
and then press the touch key  
again.  
Video  
Audio  
System  
Theme  
Favorite  
Bluetooth  
6
5
4
Source off display  
7
8
Wed 28 May  
12:45 PM  
2
This unit can be setup to dis-  
play the rear view image  
automatically when you  
move the shift lever to the  
REVERSE (R) position. For  
details about the settings,  
Source on display  
1
Radio  
Disc  
iPod  
AUX  
3
Turning the source off.  
Displaying the Bluetooth  
connection menu.  
4
Audio  
Displaying the Theme menu.  
5
Displaying the menu.  
Refer to Menu operations on  
page 57.  
6
VIDEO  
14  
En  
 
Section  
Basic operations  
04  
Selecting a source using the buttons  
7
8
Displaying the source menu.  
1
Press SRC/OFF to cycle through the sources  
listed below:  
Selecting a source using the touch panel keys  
Switching to clock adjust-  
ment display.  
Wed 28 May  
12:45 PM  
1
Touch the source icon and then touch the desired  
source name.  
!
!
!
XM XM tuner  
SIRIUS SIRIUS tuner  
Switching to HOME display  
Radio/Digital Radio Radio/Digital Radio tuner  
(Function of AVH-P2400BT/AVH-P1400DVD)  
Digital Radio Built-in Digital Radio tuner  
(Function of AVH-P4400BH/AVH-P3400BH)  
Disc Built-in DVD player  
1
Press HOME when you want to switch the dis-  
play.  
!
Turning the source on using the buttons  
Press SRC/OFF to turn the source on.  
!
!
!
!
1
USB/iPod USB/iPod  
Pandora Pandora  
Turning the source off using the buttons  
1
Press SRC/OFF and hold until the source turns  
TEL/Audio Bluetooth telephone/audio  
(Function of AVH-P1400DVD)  
Audio Built-in Bluetooth audio  
(Function of AVH-P4400BH/AVH-P3400BH/AVH-  
P2400BT)  
off.  
!
!
!
!
!
!
AUX AUX  
AV AV input  
EXT 1 External unit 1  
EXT 2 External unit 2  
When the source icon is not displayed, it can be  
displayed by touching the screen.  
While operating the menu, you cannot select a  
source by touching the source icon.  
When an HD Radio tuner (sold separately) is con-  
nected to the unit, you can select Digital Radio  
instead of Radio.  
!
!
(AVH-P2400BT/AVH-P1400DVD)  
You can select Digital Radio instead of Radio  
with these models.  
!
(AVH-P4400BH/AVH-P3400BH)  
Adjusting the volume  
Press +/(VOLUME/VOL) to adjust the volume.  
1
Notes  
!
In this manual, iPod and iPhone will be re-  
ferred to as iPod.  
!
The USB/iPod icon will change as follows:  
USB is displayed when a USB storage de-  
vice is connected.  
iPod is displayed when an iPod is con-  
nected.  
USB/iPod is displayed when no device is  
connected.  
15  
En  
 
Section  
04  
Basic operations  
!
An external unit refers to a Pioneer product,  
such as those which will be available in the fu-  
ture. Although incompatible as a source, the  
basic functions of up to two external units can  
be controlled with this unit. When two exter-  
nal units are connected, the external units are  
automatically allocated to external unit 1 or  
external unit 2.  
Viewing the hidden items  
1
Touch the scroll icon or drag the scrubber bar to  
view any hidden items.  
!
Also, you can drag the list to view any hidden  
items.  
Specifying the playback point  
1
Drag the scrubber bar on the screen.  
(Not available when the scrubber bar is grayed  
out.)  
Operating the scroll icon  
and the scrubber bar  
1
Audio  
Fader/Balance  
Graphic EQ  
Auto EQ  
F/R 0 L/R  
0
Super Bass  
On  
Sonic Center Control  
Loudness  
L/R 0  
High  
Subwoofer  
Off  
2 1  
Wed 28 May  
12:45 PM  
1
1
L+R  
1
Abcdeabcdeabcdeabcdeab  
08  
12  
01:45  
-02:45  
2
1 Scroll icon  
Appears when selectable items are hidden.  
2 Scrubber bar  
Appears when items cannot be displayed on a  
single page only.  
16  
En  
 
Section  
Basic operations  
04  
Activating the touch panel  
keys  
Displaying still images as a slide-  
show when listening to another  
source.  
You cannot view slideshows when  
DVD or USB source is selected.  
Viewing slideshows.  
1
Wed 28 May  
12:45 PM  
1
1
L+R  
1
Abcdeabcdeabcdeabcdeab  
Displaying the Favorite menu.  
08  
12  
Returning to the previous display.  
Returning to the previous list/cate-  
gory. (the folder/category one level  
higher.)  
01:45  
-02:45  
2
Return  
3
Touch panel keys  
Adjusting the LCD panel angle  
(Function of AVH-P4400BH)  
Turning the display to simpli-  
fied display.  
Returning to the normal dis-  
play by touching the screen  
anytime.  
Returning to the normal dis-  
play by touching same icon  
when playing audio.  
CAUTION  
1
Keep hands and fingers clear of the unit when  
opening, closing, or adjusting the LCD panel. Be  
especially cautious of childrens hands and fin-  
gers.  
Viewing the hidden touch  
panel keys.  
2
3
1
Press h(eject) to display the ejecting  
menu.  
Shorten the touch panel  
area.  
2
Adjust the LCD panel to an easily view-  
able angle.  
Laying the panel down.  
Common operations for  
menu settings/lists  
Returning the panel to the upright  
position.  
(AVH-P4400BH/AVH-P3400BH/AVH-  
P2400BT)  
#
As the set angle is saved, the LCD panel will  
Starting the Bluetooth telephone  
menu.  
automatically be adjusted to the same position  
the next time the LCD panel is opened.  
Displaying the list menu.  
Starting the search function.  
Ejecting a disc  
(AVH-P4400BH)  
17  
En  
 
Section  
04  
Basic operations  
CAUTION  
Keep hands and fingers clear of the unit when  
opening, closing, or adjusting the LCD panel. Be  
especially cautious of childrens hands and fin-  
gers.  
1
Press h(eject) to display the ejecting  
menu.  
2
Eject a disc.  
Ejecting a disc.  
Ejecting a disc  
(AVH-P3400BH/AVH-P2400BT/AVH-  
P1400DVD)  
%
Press h (eject).  
Setting the clock  
1
Switch to Clock Adjustment display.  
2
3
Select the item to set.  
Touch a or b to set the correct date  
and time.  
18  
En  
 
Section  
Tuner  
05  
Introduction of tuner  
operations  
Radio  
Saving song information  
(tag) from the broadcasting  
station to your iPod.  
TAG  
5
6
1
2
3
4
Tuning up or down manually.  
Touch and hold for more  
than two seconds to skip sta-  
tions. Seek tuning starts as  
soon as you release. Touch  
again to cancel seek tuning.  
Wed 28 May  
12:45 PM  
Local  
Radio  
FM1  
AM  
Abcdeabcdeabcde  
Abcdeabcdeabcde  
Abcdeabcdeabcde  
87.9  
MHz  
P.ch  
2
87.9 MHz  
Switching preset channels using the buttons  
Press c or d (TRK).  
1
6
5
Seek tuning using the buttons  
Press and hold c or d (TRK).  
1
Touch panel keys  
Selecting a band (FM1, FM2  
or FM3) by touching the left  
icon. Switching to the AM  
band by touching the right  
icon.  
Notes  
!
!
Listening AM radio while an iPod is charged  
FM1  
from this unit may generate noise. In this  
case, disconnect the iPod from this unit.  
Touch panel keys not listed under Introduction  
of tuner operations may appear on the display.  
1
AM  
The icon for the selected  
band is highlighted.  
Turning local seek tuning on  
and off.  
2
Switching the equalizer  
curves.  
3
Touch and hold for more  
than two seconds to turn the  
auto-equalizer on or off.  
Displaying the preset chan-  
nel list.  
4
19  
En  
 
Section  
06  
HD Radioä tuner  
About HD Radioä  
broadcasting  
iTunesâ Tagging provides you the opportunity to discover  
a wide range of content and the means to tagthat con-  
tent for later review and purchase from the iTunesâ  
Store.  
HD Radioä broadcasting is high quality audio  
and data services. HD Radio broadcasting is  
brought to you by your local FM/AM stations.  
HD Radio broadcasting features the following:  
!
!
!
High quality audio  
FM multicasting  
Data services  
Introduction of HD Radio  
tuner operations  
HD Radio (Built-in Digital radio tuner)  
1
2 3 4  
5
6
Blending  
Seek  
Digital  
Radio  
Wed 28 may  
12:45 PM  
Local  
D/AAuto  
All  
FM1 AM  
HD3  
Abcdeabcdeabcde  
Abcdeabcdeabcde  
Abcdeabcdeabcde  
Abcdeabcdeabcde  
87.9  
MHz  
P.CH  
2
TAG  
87.9 MHz  
9
8
7
(AVH-P4400BH/AVH-P3400BH)  
HD Radio (External Digital radio tuner)  
3 4  
5
6
1
2
Blending  
Seek  
Digital  
Radio  
Wed 28 may  
12:45 PM  
Local  
D/AAuto  
All  
FM1  
3/5  
Abcdeabcdeabcde  
Program Service Data: Contributes to the superior user  
experience of HD Radio Technology. Presents song  
name, artist, station IDs, HD2/HD3 Channel Guide, and  
other relevant data streams.  
87.9  
MHz  
P.CH  
2
TAG  
87.9 MHz  
9
8
7
(AVH-P2400BT/AVH-P1400DVD)  
Adjacent to traditional main stations are extra local FM  
channels. These HD2/HD3 Channels provide new, origi-  
nal music as well as deep cuts into traditional genre.  
This receiver is ready to receive HD Radio  
broadcasts when connected to the GEX-  
P20HD, sold separately.  
For details concerning operation, refer to the  
HD Radio tuners operation manual.  
Digital, CD-quality sound. HD Radio Technology enables  
local radio stations to broadcast a clean digital signal.  
AM sounds like todays FM and FM sounds like a CD.  
20  
En  
 
Section  
HD Radioä tuner  
06  
Touch panel keys  
Saving song information (tag)  
from the broadcasting station  
to your iPod.  
Selecting a band (FM or AM)  
TAG  
7
by touching the band key.  
The touch panel key for the  
selected band is highlighted.  
Switching between FM1,  
FM2, and FM3 by touching  
the band key.  
When AM is selected, you  
cannot switch to another AM  
band by touching the band  
key.  
FM1  
AM  
Tuning up or down manually.  
Touch and hold for more than  
two seconds to skip stations.  
Seek tuning starts as soon as  
you release. Touch again to  
cancel seek tuning.  
1
!
When an analog station is  
received, tuning down op-  
eration is conducted with-  
in the analog  
Turning local seek tuning on  
or off.  
2
3
broadcasting. (6 d 2)  
If a digital broadcast is  
not yet received, tuning-  
up operation tunes in the  
next analog station. (2 d  
6)  
!
8
Seek  
All  
Switching between Digital  
broadcasting station seek and  
normal seek.  
Seek  
HD  
Blending  
D/AAuto  
Blending  
Analog  
Switching to the analog  
broadcast of the same fre-  
quency.  
4
Switching the equalizer  
curves.  
Touch and hold for more than  
two seconds to turn the auto-  
equalizer on or off.  
Digital Radio tuner information  
Switching the digital radio tuner informa-  
tion.  
9
5
6
Switching preset channels using the buttons  
Press c or d (TRK).  
1
Seek tuning using the buttons  
Press and hold c or d (TRK).  
Displaying the preset channel  
list.  
1
Note  
Touch panel keys not listed under Introduction of  
HD Radio tuner operations may appear on the dis-  
play.  
21  
En  
Section  
07  
XM/SIRIUS tuner  
using the SIRIUS tuner, please refer to the SIR-  
IUS operation manual.  
Introduction of XM/SIRIUS  
tuner operations  
SIRIUS tuner  
!
With this unit, you can operate one addi-  
tional function: XM/SIRIUS channel direct  
selection. Refer to Selecting an XM/SIRIUS  
1
2 3  
4
5
Mode  
Wed 28 may  
12:45 PM  
Team  
SIRIUS  
All CH  
Off  
Touch panel keys  
SIRIUS1  
Abcdeabcdeabcde  
Selecting a band (XM1, XM2  
or XM3) for XM tuner.  
Selecting a band (SIRIUS1,  
SIRIUS2 or SIRIUS3) for the  
SIRIUS tuner.  
CH183  
XM1  
1
P.CH  
2
SIRIUS1  
CH183  
6
Selecting a channel by num-  
ber or category.  
Mode  
All CH  
Instant Game Team  
Replay Info Setting  
2
Mode  
Category  
7
8 9 a  
XM tuner  
Team  
1
2
4
Turning the Game Alert on or  
off for the SIRIUS tuner.  
On  
Mode  
Wed 28 may  
12:45 PM  
XM  
3
XM  
All CH  
XM1  
Team  
Abcdeabcdeabcde  
Abcdeabcdeabcde  
Abcdeabcdeabcde  
Abcdeabcdeabcde  
Off  
CH183  
Switching the equalizer  
curves.  
P.ch  
2
CH183  
4
Touch and hold for more  
than two seconds to turn the  
auto-equalizer on or off.  
7
You can use this unit to control an XM satellite  
digital tuner (GEX-P920XM), which is sold se-  
parately.  
You can use this unit to control a SIRIUS Satel-  
lite Radio tuner, which is sold separately.  
Displaying the preset chan-  
nel list.  
Selecting a channel directly.  
For details concerning operation, refer to the  
XM tuners operation manuals. This section  
provides information on XM operations with  
this unit which differs from that described in  
the XM tuners operation manual.  
5
Selecting a channel from the  
XM channel list.  
When the SIRIUS tuner is used together with  
this unit, some operations differ slightly from  
those described in the SIRIUS operation man-  
ual. This manual provides information on  
these points. For all other information on  
22  
En  
 
Section  
XM/SIRIUS tuner  
07  
Recalling radio station fre-  
quencies assigned to preset  
tuning keys.  
Selecting the channel cate-  
gory when selecting Mode  
Category.  
7
Selecting a track, fast for-  
warding/reversing or paus-  
ing/playing for the SIRIUS  
tuner.  
Instant  
Replay  
8
Displaying information on  
games for the SIRIUS tuner.  
Game  
Info  
9
a
Selecting teams for game  
alert on the SIRIUS tuner.  
Team  
Setting  
SIRIUS tuner information  
Switching the SIRIUS information.  
6
Touch and hold for more than two seconds  
to scroll the text.  
Manual tuning (step by step) using the buttons  
Press c or d (TRK).  
1
Seek tuning using the buttons  
Press and hold c or d (TRK).  
1
Notes  
!
You can also perform tuning from a desired  
channel category. (Refer to Selecting a SIRIUS  
Touch panel keys not listed under Introduction  
the display.  
!
23  
En  
Section  
08  
Playing moving images  
When playing a disc containing a mixture  
of various media file types  
Introduction of video  
playback operations  
01:45  
-02:45  
You can view DVD/DVD-R/DVD-RW/CD/CD-R/  
CD-RW/USB/iPod.  
l
!
(AVH-P4400BH)  
Touch panel keys  
Depending on your iPod, there may not be  
any output unless you use CD-IU201V (sold  
separately). Be sure to use CD-IU201V to  
connect your iPod.  
Selecting the repeat range.  
1
During playback, touch the  
point at which you want to re-  
sume playback the next time  
the disc is loaded.  
!
(AVH-P3400BH/AVH-P2400BT/AVH-  
P1400DVD)  
Depending on your iPod, there may not be  
any output unless you use CD-IU51V/CD-  
IU201V (sold separately). Be sure to use  
CD-IU51V/CD-IU201V to connect your iPod.  
2
3
Changing the screen mode.  
DVD video  
1 2 3  
4
9
Switching the equalizer  
curves.  
Wed 28 May  
12:45 PM  
1
1
L+R  
1
Abcdeabcdeabcdeabcdeab  
4
5
6
Touch and hold for more  
than two seconds to turn the  
auto-equalizer on or off.  
8 7 6 5  
12  
08  
01:45  
-02:45  
a
Switching among viewing  
angles during playback.  
Return  
b c d e  
f
h i  
Video CD  
Switching the audio output,  
when playing video discs re-  
corded with LPCM audio.  
Return  
g h d i  
Switching between stereo  
and monaural audio output,  
when playing Video CD  
discs.  
iPod video  
j
Wed 28 May  
12:45 PM  
iPod  
All  
Songs  
Switching between subtitle  
languages during playback.  
Abcdeabcdeabcdeabcdeab  
Abcdeabcdeabcdeabcdeab  
Abcdeabcdeabcdeabcdeab  
7
8
2067/12345  
Switching between audio  
languages during playback.  
01:45  
-02:45  
k
24  
En  
 
Section  
Playing moving images  
08  
Starting the search function.  
Displaying iPod menus.  
Returning to the specified  
scene to which the DVD cur-  
rently being played has been  
preprogrammed to return.  
Return  
i
j
k
l
9
Playing the video on your  
iPod in a random order.  
Pausing playback.  
Conducting operation from  
your iPod and listening to it  
using your cars speakers.  
Returning to normal play-  
back during paused, slow  
motion, or frame-by-frame  
playback.  
a
Displaying the DVD menu  
during DVD playback.  
b
c
Switching between media  
file types.  
Returning to the top menu  
during DVD playback.  
Playing back videos  
Stopping playback.  
1
Insert the disc into the disc loading slot with the  
label side up.  
If you resume playback, play-  
back will start from the point  
where you stopped. Touch  
the key again to stop play-  
back completely.  
Playback will automatically start.  
d
!
If you are playing a DVD or Video CD, a menu  
may appear. Refer to Operating the DVD menu on  
When the automatic playback function is on, the  
unit will skip the DVD menu and automatically  
start playback from the first chapter of the first  
Displaying arrow keys to op-  
erate the DVD menu.  
!
e
f
g
!
While an iPod is connected to this unit, PIONEER,  
Accessory Attached or (check mark) is dis-  
played on the iPod.  
When the source icon is not displayed, it can be  
displayed by touching the screen.  
Disconnect headphones from the iPod before  
connecting it to this unit.  
Depending on the iPod model and the amount of  
data stored in the iPod, it may take some time for  
playback to begin.  
Use the touch panel keys to select the iPod after  
connecting it to this unit.  
No Device is displayed when disconnecting the  
iPod.  
If a message is displayed after loading a disc con-  
taining DivX VOD content, touch Play.  
Refer to Playing DivXâ VOD content on page 47.  
Skipping to another title.  
Selecting a folder during  
DivX/MPEG-1/MPEG-2/  
MPEG-4 file playback.  
!
!
!
Speeding down the playback  
speed in four steps, during  
slow motion playback on  
DVD video/Video CD.  
Moving ahead one frame at a  
time during playback.  
Touch and hold for more  
than two seconds to slow  
down playback speed.  
Speeding up the playback  
speed in four steps during  
slow motion playback on  
DVD video/Video CD.  
!
!
!
h
Ejecting a disc  
!
25  
En  
Section  
08  
Playing moving images  
Selecting a chapter using the buttons  
1
Press c or d (TRK).  
Fast forwarding or reversing using the buttons  
1
Press and hold c or d (TRK).  
!
Fast forward/fast reverse may not always be possi-  
ble on some discs. In such cases, normal play-  
back will automatically resume.  
!
The fast forward/fast reverse speed depends on  
the length of time you press and hold down c or  
d (TRK). This function is not available for Video  
CD.  
Notes  
!
This DVD player can play back a DivX file re-  
corded on CD-R/RW, DVD-R/RW, or MPEG-1/  
MPEG-2/MPEG-4. (Please see the following  
section for files that can be played back. Refer  
!
!
Do not insert anything other than a DVD-R/  
RW or CD-R/RW into the disc loading slot.  
If the bookmark function is on, DVD playback  
resumes from the selected point. For more de-  
!
!
Some operations may not be available while  
watching a media due to the programming of  
the disc. In such cases, the icon appears  
on the screen.  
To ensure proper operation, connect the dock  
connector cable from the iPod directly to this  
unit.  
!
!
While the iPod is connected to this unit, the  
iPod cannot be turned on or off.  
Touch panel keys not listed under Introduction  
the display.  
26  
En  
Section  
Playing audio  
09  
Bluetooth Audio  
Introduction of sound  
playback operations  
1 2  
4
Wed 28 May  
12:45 PM  
Audio  
All  
Songs  
You can listen to DVD-R/DVD-RW/CD/CD-R/  
CD-RW/USB/iPod sound files.  
Abcdeabcdeabcdeabcdeab  
Abcdeabcdeabcdeabcdeab  
Abcdeabcdeabcdeabcdeab  
125  
Audio CD  
1 2  
3 4  
5
Wed 28 May  
12:45 PM  
S.Rtrv  
ROM  
Disc  
On  
01:45  
-02:45  
Abcdeabcdeabcdeabcdeab  
Abcdeabcdeabcdeabcdeab  
Abcdeabcdeabcdeabcdeab  
9
!
Depending on the Bluetooth audio player  
connected to this unit, the available opera-  
tions will be limited to the following two le-  
vels:  
A2DP profile (Advanced Audio Distribu-  
tion Profile): You can only playback  
songs on your audio player.  
87  
125  
01:45  
-02:45  
9
8
7
6
5
iPod audio (Control Audio)  
f
1 a b 3 4 i  
AVRCP profile (Audio/Video Remote  
Control Profile): You can perform play-  
back, pause playback, select songs, etc.  
Since there are a number of Bluetooth  
audio players available on the market, avail-  
able operations will vary extensively. When  
operating your player with this unit, refer to  
the instruction manual that came with your  
Bluetooth audio player as well as this man-  
ual.  
As the signal from your cellular phone may  
cause noise, avoid using it when you are  
listening to songs on your Bluetooth audio  
player.  
When a call is in progress on the cellular  
phone connected to this unit via Bluetooth  
wireless technology, the sound of the  
Bluetooth audio player connected to this  
unit is muted.  
Wed 28 May  
12:45 PM  
S.Rtrv  
iPod  
All  
Songs  
Abcdeabcdeabcdeabcdeab  
Abcdeabcdeabcdeabcdeab  
Abcdeabcdeabcdeabcdeab  
!
2067/12345  
01:45  
-02:45  
c d  
e
9
h
g
iPod audio (App Mode)  
!
!
!
!
(AVH-P4400BH)  
Depending on your iPod, there may not be  
any output unless you use CD-IU201V (sold  
separately). Be sure to use CD-IU201V to  
connect your iPod.  
(AVH-P3400BH/AVH-P2400BT/AVH-  
P1400DVD)  
Depending on your iPod, there may not be  
any output unless you use CD-IU51V/CD-  
IU201V (sold separately). Be sure to use  
CD-IU51V/CD-IU201V to connect your iPod.  
!
!
The play time may not display correctly.  
Depending on the type of Bluetooth audio  
player you have connected to this unit, op-  
eration and information display may not be  
available for some functions.  
27  
En  
 
Section  
09  
Playing audio  
Touch panel keys  
Switching the text infor-  
mation to display on this  
unit when playing MP3/  
WMA/AAC files.  
Selecting the repeat  
range.  
8
9
a
1
Pausing and starting  
playback.  
Playing songs in random  
order.  
2
Playing songs on the  
iPod in random order.  
Switching the S.Rtrv  
(sound retriever) function  
setting when playing  
audio.  
Changing the speed of  
audiobook playback on  
the iPod.  
3
b
c
Switching the equalizer  
curves.  
Touch and hold for more  
than two seconds to turn  
the auto-equalizer on or  
off.  
Switching to Link Search  
mode to play songs re-  
lated to the currently  
playing song on the iPod.  
4
Conducting operation  
from your iPod and listen-  
ing to it using your cars  
speakers.  
Displaying a list of track  
titles/file names to select  
songs on a CD.  
Displaying the file name  
list to select the files.  
Displaying iPod menus.  
d
e
Performing operations  
from this unit and listen-  
ing to the music on your  
iPod using your cars  
speakers.  
5
Switching between  
media file types on a  
DVD/CD/USB.  
6
7
Selecting a folder.  
28  
En  
Section  
Playing audio  
09  
Text information  
Note  
Touch panel keys not listed under Introduction of  
sound playback operations may appear on the dis-  
play.  
Displaying the Songs list  
on the iPod.  
f
Displaying the Artists list  
on the iPod.  
Setting up for Bluetooth audio  
g
Before you can use the Bluetooth audio func-  
tion you must set up the unit for use with your  
Bluetooth audio player. This entails establish-  
ing a Bluetooth wireless connection between  
this unit and your Bluetooth audio player, and  
pairing your Bluetooth audio player with this  
unit.  
Displaying the Albums  
list on the iPod.  
h
Artwork display  
1
Connection  
Starting Album Link Search on your iPod  
when you touch the artwork display.  
First, you need to connect a Bluetooth audio to  
this unit.  
For detailed instructions on connecting your  
Bluetooth audio to this unit via Bluetooth wireless  
i
Playing back sound  
1
Insert the disc into the disc loading slot with the  
label side up.  
Notes  
Playback will automatically start.  
While an iPod is connected to this unit, PIONEER,  
Accessory Attached or (check mark) is dis-  
played on the iPod.  
When the source icon is not displayed, it can be  
displayed by touching the screen.  
Disconnect headphones from the iPod before  
connecting it to this unit.  
Depending on the iPod model and the amount of  
data stored in the iPod, it may take some time for  
playback to begin.  
Use the touch panel keys to select the iPod after  
connecting it to this unit.  
!
When playing back files recorded as VBR  
!
(variable bit rate) files, the play time will not be  
correctly displayed if fast forward or reverse  
operations are used.  
!
!
!
!
To ensure proper operation, connect the dock  
connector cable from the iPod directly to this  
unit.  
!
!
While the iPod is connected to this unit, the  
iPod cannot be turned on or off.  
If the characters recorded on the disc are not  
compatible with this unit, those characters  
will not be displayed.  
!
!
No Device is displayed when disconnecting the  
iPod.  
!
Text information may not be correctly dis-  
played depending on the recorded environ-  
ment.  
Ejecting a disc  
!
!
!
Disconnect the USB portable audio player/  
USB memory when you are done using it.  
When you select Clock or Speana on Select-  
work is not displayed.  
Selecting a track using the buttons  
1
Press c or d (TRK).  
Fast forwarding or reversing using the buttons  
1
Press and hold c or d (TRK).  
29  
En  
Section  
â
10  
Using Pandora  
!
!
Connection to the Internet via 3G, EDGE or Wi-  
Fi network.  
Optional Pioneer adapter cable connecting  
your iPhone to the Pioneer car audio/video  
products.  
Introduction of Pandora  
operations  
You can play the Pandora by connecting your  
iPod which was installed the Pandora applica-  
tion.  
Limitations:  
8
1 2  
3
!
Access to the Pandora service will depend on  
the availability of a cellular and/or Wi-Fi net-  
work for purposes of allowing your iPhone to  
connect to the Internet.  
Pandoras service is currently only available in  
the U.S.  
Wed 28 May  
12:45 PM  
S.Rtrv  
Pandora  
Abcdeabcdeabcdeabcde  
Abcdeabcdeabcdeabcde  
Abcdeabcdeabcdeabcde  
Abcdeabcdeabcdeabcde  
!
!
Ability of the Pioneer car audio/video products  
to access the Pandora service is subject to  
change without notice and could be affected  
by any of the following: compatibility issues  
with future firmware versions of iPhones;  
compatibility issues with future firmware ver-  
sions of the Pandora application for the  
iPhone; changes to the Pandora music service  
by Pandora; discontinuation of the Pandora  
music service by Pandora.  
Certain functionality of the Pandora service is  
not available when accessing the service  
through the Pioneer car audio/video products,  
including, but not limited to, creating new sta-  
tions, deleting stations, emailing current sta-  
tions, buying tracks from iTunes, viewing  
additional text information, logging in to  
Pandora, and adjusting Cell Network Audio  
Quality.  
01:45  
-02:45  
7
6 5 4  
Important  
Requirements to access the Pandora music ser-  
vice using the Pioneer car audio/video products:  
!
iPod compatibility  
iPhone (first generation), iPhone 3G, iPhone  
3GS, iPhone 4G, iPod touch 1G, iPod touch  
2G, iPod touch 3G or iPod touch 4G (firmware  
version 3.0 or later).  
Certain firmware versions for the iPod touch  
and iPhone may not be compatible with the  
Pandora application. If this appears to be the  
case, please update the firmware to a version  
that is compatible with Pandora.  
Latest version of the Pandora application for  
the iPhone, downloaded to your device.  
(Search Apple iTunes App Store for  
Pandora).  
Current Pandora account (Free account and  
paid accounts available from Pandora; create  
a free account online at  
!
!
!
Pandora Internet radio is a music service not af-  
filiated with Pioneer. More information is avail-  
able at http://www.pandora.com.  
You can play the Pandora by connecting your  
iPod which was installed the Pandora applica-  
tion and starting up the Pandora application.  
http://www.pandora.com/register or through  
the Pandora application for the iPhone).  
iPhone Data Plan.  
!
Note: If the Data Plan for your iPhone does  
not provide for unlimited data usage, addi-  
tional charges from your carrier may apply for  
accessing the Pandora service via 3G and/or  
EDGE networks.  
30  
En  
 
Section  
â
Using Pandora  
10  
Touch panel keys  
Note  
Touch panel keys not listed under Introduction of  
Pandora operations may appear on the display.  
Switching the S.Rtrv  
(sound retriever) function  
setting while playing  
Pandora.  
1
Switching the equalizer  
curves.  
Touch and hold for more  
than two seconds to turn  
the auto-equalizer on or  
off.  
2
Displaying the QuickMix/  
station list to select  
QuickMix or the desired  
station.  
3
4
Giving a Thumbs-upfor  
the track currently play-  
ing.  
Giving a Thumbs-down”  
for the track currently  
playing and then skip-  
ping to the next track.  
5
6
Storing track information  
(Bookmark).  
Pausing and starting  
playback.  
7
Text information  
8
Playing the station list.  
Playing tracks  
1
Open the USB port cover.  
2
Connect an iPod to the USB cable using an iPod  
Dock Connector.  
3
Start up the Pandora application installed on the  
iPod.  
Skipping tracks  
Press d.  
1
31  
En  
Section  
11  
Playing still images  
Introduction of still image  
playback operations  
You can view still images saved in CD-R/CD-  
RW/USB.  
5
6
Selecting a folder.  
Still image  
Capturing an image in  
JPEG files.  
1 2 3  
4
Wed 28 May  
12:45 PM  
Photo  
Off  
Full  
Rotating the displayed pic-  
ture 90° clockwise.  
Abcdeabcdeabcde  
Abcdeabcdeabcde  
7
8
2
2
Starting or pausing the sli-  
deshow.  
Capture  
Switching between media  
file types when there is  
more than one media file  
type saved to the CD-R/RW  
or USB device. This key  
does not appear if there is  
only one media file type  
saved to the CD-R/RW or  
USB device.  
8
7 6  
5
When playing a disc containing a mixture  
of various media file types  
9
9
When loading a CD-R/RW or USB containing  
JPEG picture files, this unit starts a slideshow  
from the first folder/picture on the disc/device.  
The table below shows the controls for viewing  
a slideshow.  
Playing still images  
1
Insert the disc into the disc loading slot with the  
label side up.  
Touch panel keys  
Playback will automatically start.  
When the source icon is not displayed, it can be  
displayed by touching the screen.  
!
Selecting the repeat range.  
1
2
Ejecting a disc.  
!
Playing files in a random  
order.  
Selecting a file using the buttons  
Press c or d (TRK).  
1
Fast file searching  
1
!
Changing the screen  
mode.  
Press and hold c or d (TRK).  
You can search 10 JPEG files at a time.  
3
4
Notes  
!
Displaying the file name  
list to select the files.  
Files are played back in file number order and  
folders are skipped if they contain no files. (If  
folder 1 (ROOT) contains no files, playback  
commences with folder 2.)  
!
Touch panel keys not listed under Introduction  
on the display.  
32  
En  
 
Section  
Playing still images  
11  
Introduction of still image  
playback as a slideshow  
operations  
You can view still images saved in CD-R/CD-  
RW/USB as a slideshow when listening to an-  
other source.  
Rotating the displayed pic-  
ture 90° clockwise.  
7
8
Starting or pausing the sli-  
deshow.  
1
Start slideshow when listening to an-  
other source.  
1 2 3  
4
5
Off  
Full  
Displaying still images as a slide-  
show.  
2
Select the device containing the files  
Capture  
that you want to display.  
!
!
Disc Built-in DVD player  
USB/iPod USB/iPod  
8
7 6  
The table below shows the controls for viewing  
a slideshow.  
#
To cancel searching, touch Cancel.  
Notes  
Touch panel keys  
!
This unit cannot be used to view still images  
on disc or by USB/iPod as a slideshow when  
the corresponding source, Disc or USB/iPod,  
is selected.  
Touch panel keys not listed under Introduction  
tions may appear on the display.  
Selecting the repeat range.  
1
2
!
Playing files in a random  
order.  
Changing the screen  
mode.  
3
4
Selecting a folder.  
Selecting a file.  
5
6
Capturing an image in  
JPEG files.  
33  
En  
 
Section  
12  
Bluetooth telephone  
!
!
If you are unable to complete the connection  
using this unit, use the device to connect to  
the unit.  
If you connect more than one device at a time,  
connected device may not operate properly.  
Connecting one device at a time is recom-  
mended.  
Introduction of Bluetooth  
telephone operations  
You can use Bluetooth telephone (AVH-  
P4400BH/AVH-P3400BH/AVH-P2400BT).  
Telephone standby display  
1
Wed 28 May  
12:45 PM  
1
1 Incoming call notice  
Radio  
AM  
FM1  
ABCDEHGHI 01  
012345678901  
Indicates that an incoming call has been re-  
ceived and has not been checked yet.  
Abcdeabcdeabcde  
Abcdeabcdeabcde  
!
Not displayed for calls made when your  
cellular phone is disconnected from this  
unit.  
P.CH  
2
Off  
On  
87.9 MHz  
Touch panel keys  
6 5 7  
2 4 3  
Switching the mode to enter  
the phone number directly.  
1
1
When switching to the entering phone  
number mode  
Wed 28 may  
12:45 PM  
1
Switching to the call history  
list.  
ABCDEHGHI 01  
012345678901  
1
4
7
2
5
8
0
3
6
9
2
3
Off  
#
*
C
+
Switching to the phone book  
mode.  
8 b 9 a  
Important  
!
!
Since this unit is on standby to connect with  
your cellular phone via Bluetooth wireless  
technology, using it without the engine run-  
ning can drain the battery power.  
Advanced operations that require attention  
such as dialing numbers on the monitor, etc.,  
are prohibited while driving. Park your vehicle  
in a safe place when using these advanced  
operations.  
Operations available may be limited depend-  
ing on the cellular phone connected to this  
unit.  
Be sure to park your vehicle in a safe place  
and apply the parking brake when performing  
this operation.  
Displaying the preset dial  
screen.  
4
5
6
7
Turning the ring tone for in-  
coming calls on or off.  
Turning automatic answering  
on or off.  
!
!
Displaying the Bluetooth  
connection menu.  
Refer to the instructions  
34  
En  
 
Section  
Bluetooth telephone  
12  
Turning private mode on or  
off.  
1
Connection  
First, you need to connect a Bluetooth telephone  
to this unit.  
8
For detailed instructions on connecting your  
phone to this unit via Bluetooth wireless technol-  
ogy, see following section. Using a Bluetooth de-  
Adjusting the other partys  
listening volume.  
9
2
Volume adjustment  
Adjust the earpiece volume of your cellular phone  
to your preference. The unit will record the ad-  
justed volume level as the default setting.  
Ending a call.  
Rejecting an incoming call.  
Canceling call waiting.  
a
!
!
!
The volume of the callers voice and ring tone  
may vary depending on the type of cellular  
phone.  
If there is a large volume difference between  
the ring tone and callers voice, the overall vo-  
lume level may become unstable.  
Make sure to adjust the volume to a proper  
level before disconnecting the cellular phone  
from the unit. If the volume is muted (zero  
level) on your cellular phone, the volume level  
of your cellular phone remains muted even  
after the cellular phone is disconnected.  
Accepting an incoming call.  
Making a phone call, when  
selecting a phone number.  
Switching between callers on  
hold.  
b
Notes  
!
!
!
Private mode can only be operated while you  
are talking on the phone.  
To end the call, both you and the other caller  
must hang up your phones.  
Touch panel keys not listed under Introduction  
on the display.  
Setting up for hands-free phoning  
Before you can use the hands-free phoning  
function you must set up the unit for use with  
your cellular phone. This entails establishing a  
Bluetooth wireless connection between this  
unit and your phone, registering your phone  
with this unit, and adjusting the volume level.  
35  
En  
Section  
13  
Using Bluetooth wireless technology  
Touch panel keys  
Introduction of Bluetooth  
telephone operations  
Accepting an incoming call.  
Making a phone call, when  
selecting a phone number  
from the dialed and received  
call history.  
1
2
You can use Bluetooth wireless technology  
(AVH-P1400DVD).  
During a call  
Ending a call.  
Rejecting an incoming call.  
Canceling call waiting.  
1
2
3
Wed 28 May  
12:45 PM  
TEL  
Switching the equalizer  
curves.  
Abcdeabc  
3
Touch and hold for more  
than two seconds to turn the  
auto-equalizer on or off.  
Text  
Scroll  
REG  
9 8 7 6 5 4  
Except during a call  
Turning the ring tone for in-  
coming calls on or off.  
Text  
REG  
Scroll  
Touch and hold for more  
than two seconds to display  
the Bluetooth device address  
of your cellular phone and  
the Bluetooth adapter.  
a
4
When you connect a Bluetooth adapter (e.g.  
CD-BTB200)(sold separately) to AVH-  
P1400DVD, you can control Bluetooth tele-  
phone.  
Turning automatic answering  
on or off.  
But the available features are limited.  
Touch and hold for more  
than two seconds to connect  
to a Bluetooth telephone  
automatically.  
Important  
!
!
In some countries, CD-BTB200 is not sold on  
the market.  
5
Since this unit is on standby to connect with  
your cellular phone via Bluetooth wireless  
technology, using it without the engine run-  
ning can drain the battery power.  
Advanced operations that require attention  
such as dialing numbers on the monitor, etc.,  
are prohibited while driving. Park your vehicle  
in a safe place when using these advanced  
operations.  
!
!
Registering connected cellu-  
lar phone to take full advan-  
tage of the features available  
with Bluetooth wireless tech-  
nology.  
Touch and hold for more  
than two seconds to termi-  
nate the Bluetooth wireless  
connection.  
6
Operations available may be limited depend-  
ing on the cellular phone connected to this  
unit.  
36  
En  
 
Section  
Using Bluetooth wireless technology  
13  
Scrolling the phone number.  
1
Connection  
Touch and hold for more  
than two seconds to activate  
connection mode on this  
unit and establish a  
Bluetooth wireless connec-  
tion from your phone.  
First, you need to connect a Bluetooth telephone  
to this unit.  
Text  
For detailed instructions on connecting your  
phone to this unit via Bluetooth wireless technol-  
ogy, see following section. Using a cellular phone  
Volume adjustment  
Scroll  
7
2
Adjust the earpiece volume of your cellular phone  
to your preference. The unit will record the ad-  
justed volume level as the default setting.  
Displaying the dialed call his-  
tory.  
Selecting a phone number  
from the call history.  
!
!
!
The volume of the callers voice and ring tone  
may vary depending on the type of cellular  
phone.  
If there is a large volume difference between  
the ring tone and callers voice, the overall vo-  
lume level may become unstable.  
Make sure to adjust the volume to a proper  
level before disconnecting the cellular phone  
from the unit. If the volume is muted (zero  
level) on your cellular phone, the volume level  
of your cellular phone remains muted even  
after the cellular phone is disconnected.  
8
Displaying the received/  
missed call history.  
Selecting a phone number  
from the call history.  
9
Switching between  
Bluetooth telephone and  
Bluetooth audio.  
Touch and hold for more  
than two seconds to start  
voice recognition.  
Bluetooth audio operations  
When you connect a Bluetooth adapter (e.g.  
CD-BTB200)(sold separately) to AVH-  
P1400DVD, you can control Bluetooth audio.  
a
Important  
Note  
!
Depending on the Bluetooth audio player con-  
nected to this unit, the available operations  
will be limited to the following two levels:  
A2DP profile (Advanced Audio Distribution  
Profile): You can only playback songs on  
your audio player.  
Touch panel keys not listed under Introduction of  
the display.  
AVRCP profile (Audio/Video Remote Con-  
trol Profile): You can perform playback,  
pause playback, select songs, etc.  
Since there are a number of Bluetooth audio  
players available on the market, available op-  
erations will vary extensively. When operating  
your player with this unit, refer to the instruc-  
tion manual that came with your Bluetooth  
audio player as well as this manual.  
Setting up for hands-free phoning  
Before you can use the hands-free phoning  
function you must set up the unit for use with  
your cellular phone. This entails establishing a  
Bluetooth wireless connection between this  
unit and your phone, registering your phone  
with this unit, and adjusting the volume level.  
!
37  
En  
 
Section  
13  
Using Bluetooth wireless technology  
!
!
Information related to a song (such as the  
elapsed playing time, song title, song index,  
etc.) cannot be displayed on this unit.  
Setting the action for c and d  
icons.  
As the signal from your cellular phone may  
cause noise, avoid using it when you are lis-  
tening to songs on your Bluetooth audio  
player.  
Auto  
Switching the equalizer curves.  
Touch and hold for more than two  
seconds to turn the auto-equalizer  
on or off.  
!
When a call is in progress on the cellular  
phone connected to this unit via Bluetooth  
wireless technology, the sound of the  
Bluetooth audio player connected to this unit  
is muted.  
When the Bluetooth audio player is in use,  
you cannot connect to a Bluetooth telephone  
automatically.  
!
!
Note  
Touch panel keys not listed under Bluetooth audio  
operations may appear on the display.  
Playback continues even if you switch from  
your Bluetooth audio player to another source  
while listening to a song.  
Touch panel keys  
Setting up for Bluetooth audio  
Switching between Bluetooth tele-  
phone and Bluetooth audio.  
Before you can use the Bluetooth audio func-  
tion you must set up the unit for use with your  
Bluetooth audio player. This entails establish-  
ing a Bluetooth wireless connection between  
this unit and your Bluetooth audio player, and  
pairing your Bluetooth audio player with this  
unit.  
Skipping back or forward to an-  
other track when Auto is set for  
the auto/manual setting.  
Performing fast forward or reverse  
when Manual is set for the auto/  
manual setting.  
Pausing a song.  
1
Connection  
Touch and hold for more than two  
seconds to activate connection  
mode on this unit and establish a  
Bluetooth wireless connection  
from your player.  
First, you need to connect a Bluetooth audio to  
this unit.  
For detailed instructions on connecting your  
Bluetooth audio to this unit via Bluetooth wireless  
F1  
F2  
Playback starts.  
Touch and hold for more than two  
seconds to terminate the  
Bluetooth wireless connection.  
38  
En  
Section  
Detailed instructions  
14  
2
Touch BSM to turn BSM on.  
Storing and recalling stations  
You can easily store up to six stations for each  
band as presets.  
The six strongest broadcast frequencies will  
be stored under preset tuning keys in order of  
their signal strength.  
!
!
Six stations for each band can be stored in  
memory.  
#
To cancel the storage process, touch  
Cancel.  
Channels are stored and recalled on a  
broadcast station basis. This means that if  
the broadcast station you stored has been  
assigned to a different channel by SIRIUS,  
you can still recall the same broadcast sta-  
tion (though a different channel number  
may appear in the display).  
Tuning in to strong signals  
Local seek tuning lets you tune in to only  
those radio stations with sufficiently strong  
signals for good reception.  
1
Display the preset channel list screen.  
FM: Off —  
AM: Off —  
The highest level setting allows reception of  
only the strongest stations, while lower levels  
allow the reception of weaker stations.  
The preset channel list appears in the display.  
Tuning in to strong HD  
Radio signals  
Local seek tuning lets you tune in to only  
those radio stations with sufficiently strong  
signals for good reception.  
2
Touch and hold one of the preset tun-  
ing keys to store the selected frequency in  
the memory.  
The selected radio station frequency has been  
stored in the memory.  
3
Touch one of the preset tuning keys to  
1
Display the local setting screen.  
select the desired station.  
2
#
Touch On on Local to turn on.  
To turn off, touch Off.  
Storing the strongest stations  
BSM (best stations memory) automatically  
stores the six strongest stations in the order of  
their signal strength.  
3
Touch c or d on Level to select the de-  
sired level.  
Storing broadcast frequencies with BSM may  
replace broadcast frequencies you have saved  
using the preset tuning keys.  
(AVH-P2400BT/AVH-P1400DVD)  
Level1Level2Level3Level4  
(AVH-P4400BH/AVH-P3400BH)  
FM: Level1Level2Level3Level4  
AM: Level1Level2  
1
Display the preset channel list screen.  
#
The highest level setting allows reception of  
only the strongest stations, while lower levels  
allow the reception of weaker stations.  
The preset channel list appears in the display.  
39  
En  
 
Section  
14  
Detailed instructions  
Using iTunes tagging  
You can store the information if the TAG indi-  
cator is displayed while the desired song is  
being broadcast.  
This function can be operated with the following  
iPod models.  
iPod touch 4th generation  
iPod touch 3rd generation  
iPod touch 2nd generation  
iPod touch 1st generation  
iPod classic 160GB  
iPod classic 120GB  
iPod classic  
iPod with video  
iPod nano 6th generation  
#
While storing the tag data on this unit, TAG  
flashes.  
#
The tag information for up to 50 songs can be  
stored on this unit.  
Depending on the timing of when the tag infor-  
mation is stored, the tag information for the song  
played before or after the currently playing song  
may also be stored.  
iPod nano 5th generation  
iPod nano 4th generation  
3
When completed,  
indicator turns  
iPod nano 3rd generation  
off and indicator is displayed.  
iPhone 4  
iPhone 3GS  
iPhone 3G  
iPhone  
Storing the tagged information  
to your iPod  
However, tag information can be stored in this  
unit even while other iPod models are used.  
When you want to use this function in the HD  
Radio tuner source, use an HD Radio tuner  
(GEX-P20HD).  
1
Connect your iPod.  
When your iPod is connected to this unit, your  
iPod starts storing the tagged information  
automatically.  
The song information (tag) can be saved from  
the broadcasting station to your iPod. The  
songs will show up in a playlist called Tagged  
playlistin iTunes the next time you sync your  
iPod. Then you can directly buy the songs you  
want from the iTunes Store.  
The tagged songs and the song that you can  
buy from the iTunes Store may be different.  
Make sure to confirm the song before you  
make the purchase.  
2
When completed,  
indicator turns off  
and the tagged information is stored on  
your iPod.  
Switching the media file type  
When playing a disc containing a mixture of  
various media file types, such as DivX, MPEG-  
1, MPEG-2, MPEG-4 and MP3, you can switch  
between media file types to play.  
Audio data (CD-DA) and JPEG picture files on  
DVD-R/RW/ROM cannot be played back on  
this unit.  
If you cannot use this function normally, up-  
date your iPod firmware.  
Storing the tag information to  
this unit  
CD (audio data (CD-DA))Music/ROM (com-  
pressed audio)Video (DivX, MPEG-1,  
MPEG-2, MPEG-4 video files)Photo (JPEG  
picture files)  
1
Tune in to the broadcast station.  
2
Store the tag information to this unit.  
40  
En  
 
Section  
Detailed instructions  
14  
Operating the DVD menu  
(Function for DVD video)  
Some DVDs allow you to make a selection  
from the disc contents using a menu.  
Operating this units iPod  
function from your iPod  
You can listen to the sound from your iPod ap-  
plications using your cars speakers, when  
App Mode is selected.  
This function is not compatible with the follow-  
ing iPod models.  
Using the arrow keys  
1
Display arrow keys to operate the DVD  
!
!
iPod nano 1st generation  
iPod with video  
menu.  
Refer to Playing moving images on page 24.  
!
While this function is in use, the iPod will  
not turn off even if the ignition key is turned  
off. Operate the iPod to turn off the power.  
2
Select the desired menu item.  
1
Switch the control mode to App Mode.  
Selecting the desired menu item.  
2
Operate the connected iPod to select a  
video/song and play.  
Starting playback from the se-  
lected menu item.  
Notes  
!
The following functions are still accessible  
from the unit even if the control mode is set to  
App Mode.  
Operating the DVD menu by di-  
rectly touching the menu item.  
However, the operation will depend on your  
applications.  
Playing/pausing  
Fast forwarding/reversing  
Tracking up/down  
#
When operating the DVD menu by directly  
touching the menu item, touch the icon to oper-  
ate.  
Moving to a chapter up/down  
App Mode is compatible with the following  
iPod models.  
Returning to the normal DVD video  
display.  
!
iPod touch 4th generation  
iPod touch 3rd generation  
iPod touch 2nd generation  
iPod touch 1st generation  
iPod classic 160GB  
iPod classic 120GB  
iPod classic  
iPod nano 6th generation  
iPod nano 5th generation  
iPod nano 4th generation  
iPod nano 3rd generation  
Displaying arrow keys.  
#
Ways to display the menu will differ depend-  
ing on the disc.  
Depending on the contents of the DVD disc,  
this function may not work properly. In such  
cases, use the touch panel keys to operate the  
DVD menu.  
#
41  
En  
 
Section  
14  
Detailed instructions  
iPod nano 2nd generation  
iPhone 4  
iPhone 3GS  
iPhone 3G  
!
If you select another folder during repeat  
play, the repeat play range changes to Disc.  
If you select USB source, the repeat play  
range changes to All.  
iPhone  
!
!
!
!
If you perform track search or fast forward/  
reverse during File, the repeat play range  
changes to Folder.  
If you perform title/chapter search or fast  
forward/reverse during Chapter, the repeat  
play is set to off automatically.  
If you perform track search or fast forward/  
reverse during Track, the repeat play range  
changes to Disc.  
When Folder is selected, it is not possible  
to play back a subfolder of that folder.  
Random play (shuffle)  
iPod-videos/songs can be played back in ran-  
dom order.  
!
!
!
!
!
!
Songs Play back videos/songs in the se-  
lected list in random order.  
Albums Play back videos/songs from a  
randomly selected album in order.  
Folder Play back songs/tracks in the se-  
lected folder in random order.  
Disc Play back songs/tracks in the se-  
lected disc in random order.  
On Play back files in random order within  
the repeat range, Folder and Disc.  
Off Cancel random play.  
Playing videos from your iPod  
(Function for iPod)  
Videos can be played on this unit if an iPod  
with video capabilities is connected.  
!
This unit can play back Movies, Music vi-  
deos, Video Podcastand TV show”  
which are downloaded from the iTunes  
store.  
Repeating playback  
!
!
!
!
!
!
!
!
Disc Play through the current disc  
Chapter Repeat the current chapter  
Title Repeat the current title  
Track Repeat the current track  
File Repeat the current file  
Folder Repeat the current folder  
One Repeat just the current video/song  
All Repeat all videos/songs in the se-  
lected list on the iPod  
1
Display the iPod menus.  
Refer to Playing moving images on page 24.  
2
Switch to iPod video mode.  
>
Playlists  
Artists  
Albums  
Songs  
Podcasts  
Video  
Genres  
!
!
!
This function cannot be operated during  
Video CD playback featuring PBC (playback  
control).  
If you perform chapter search, fast forward/  
reverse, frame-by-frame playback or slow  
motion playback, the repeat play will stop.  
When playing discs with compressed audio  
and audio data (CD-DA), playback is re-  
peated within the type of data currently  
playing even if Disc is selected.  
#
If you want to switch to iPod video mode,  
touch the icon.  
Switching to iPod video mode.  
Video  
42  
En  
 
Section  
Detailed instructions  
14  
!
!
Composers (composers)  
Audiobooks (audiobooks)  
3
Play the video from the iPod.  
>
Playlists  
Artists  
3
Touch the title of the list that you want  
to play.  
Albums  
Songs  
Repeat this operation until you find the de-  
sired video/music.  
Podcasts  
Video  
Genres  
Notes  
!
You can play playlists created with the PC ap-  
plication (MusicSphere). The application will  
be available on our website.  
#
If you want to switch to iPod music mode,  
touch the icon.  
!
Playlists that you created with the PC applica-  
tion (MusicSphere) are displayed in abbre-  
viated form.  
Switching to iPod music mode.  
Music  
Searching the list by alphabet  
(Function for iPod)  
Browsing for a video/music  
on the iPod  
1
Select a category.  
(Function for iPod)  
To make operating and searching easy, opera-  
tions to control an iPod with this unit are de-  
signed to be as similar to the iPod as possible.  
2
Switch to alphabet search mode.  
Switching to alphabet search mode.  
Searching for a video/music by  
category  
Alphabet search mode is displayed.  
Touch the first letter of the title of the  
1
Display the iPod menus.  
3
Refer to Playing moving images on page 24.  
video/song you are looking for.  
While searching, touch panel key operation is  
not available.  
Refer to Playing audio on page 27.  
2
Touch one of the categories in which  
you want to search for a video/music.  
#
To refine the search with a different letter,  
!
!
!
!
!
!
!
!
!
!
!
!
Video Playlists (video playlists)  
Movies (movies)  
Music Videos (music videos)  
Video Podcasts (video podcasts)  
TV Shows (TV shows)  
Rentals (rentals)  
Playlists (playlists)  
Artists (artists)  
Albums (albums)  
Songs (songs)  
touch Cancel.  
4
Touch the title of the list that you want  
to play.  
Repeat this operation until you find the de-  
sired song/video.  
Resume playback (Bookmark)  
(Function for DVD video)  
Podcasts (podcasts)  
Genres (genres)  
43  
En  
 
Section  
14  
Detailed instructions  
By using the Bookmark function, you can re-  
sume playback from a selected scene the next  
time the disc is loaded.  
1
Start the search function.  
Refer to Playing moving images on page 24.  
2
Touch the desired search option (e.g.,  
The selected scene will be bookmarked so that  
playback resumes from that point next time.  
Chapter).  
3
Touch 0 to 9 to input the desired num-  
!
To clear the bookmark on a disc, touch and  
hold the key during playback.  
The oldest bookmark is replaced by the  
new one.  
ber.  
#
To cancel the entered numbers, touch C.  
!
4
Start playback from the selected part.  
Registering the numbers and start-  
ing playback.  
Frame-by-frame playback  
(Function for DVD video/video CD/DivX file/  
MPEG-1/MPEG-2/MPEG-4)  
Note  
With discs featuring a menu, you can also use  
the DVD menu to make your selection.  
Refer to Playing moving images on page 24.  
Note  
Images during frame-by-frame playback may be  
unclear for some discs.  
Changing audio language  
during playback (Multi-audio)  
Slow motion playback  
Notes  
With DVDs/DivX files that provides audio play-  
back in different languages and different  
audio systems (Dolby Digital, DTS, etc.), you  
can switch between languages/audio systems  
during playback.  
!
!
!
There is no sound during slow motion play-  
back.  
Images during slow motion playback may be  
unclear for some discs.  
Reverse slow motion playback is not  
available.  
Notes  
!
!
!
!
With some DVDs, switching between lan-  
guages/audio systems may only be possible  
using a menu display.  
You can also switch between languages/audio  
systems using Video Setup menu. For details,  
Depending on the setting, the video may not  
be played back with the audio system used to  
record the DVD.  
Searching for the part you  
want to play  
You can use the search function to find the  
part you want to play.  
For DVD videos, you can select Title (title),  
Chapter (chapter) or 10key (numeric keypad).  
For video CDs, you can select Track (track) or  
10key (numeric keypad).  
You will return to normal playback if you  
change the Audio during fast forward/fast re-  
verse, pause or slow motion playback.  
!
Chapter search is not available when disc  
playback is stopped.  
!
This function cannot be operated during  
some DVD videos or Video CD playback  
featuring PBC (playback control).  
44  
En  
 
Section  
Detailed instructions  
14  
This function cannot be used if a specified  
scene has not been preprogrammed on the  
DVD disc.  
Changing the subtitle  
language during playback  
(Multi-subtitle)  
With DVDs/DivX files featuring multi-subtitle  
recordings, you can switch between subtitle  
languages during playback.  
Selecting audio output  
When playing DVD video discs recorded with  
LPCM audio, you can switch the audio output.  
When playing video CDs, you can switch be-  
tween stereo and monaural audio output.  
Notes  
!
With some DVDs, switching between subtitle  
languages may only be possible using a menu  
display.  
!
This function is not available when disc  
playback is stopped.  
!
You can also switch between subtitle lan-  
guages using Video Setup menu. For details,  
!
!
!
!
L+R Left and right  
Left Left  
Right Right  
!
You will return to normal playback if you  
change the Subtitle during fast forward/fast  
reverse, pause or slow motion playback.  
Mix Mixing left and right  
Note  
You may not be able to select or use this function  
depending on the disc and the playback  
location.  
Changing the viewing angle  
during playback (Multi-angle)  
With DVDs featuring multi-angle (scenes shot  
from multiple angles) recordings, you can  
switch among viewing angles during play-  
back.  
PBC playback  
(Function for Video CDs)  
During playback of Video CDs featuring PBC  
(playback control), PBC On is displayed.  
!
During playback of a scene shot from mul-  
tiple angles, the angle icon is displayed.  
Use the Video Setup menu to turn the  
angle icon display on or off. For details,  
1
Start the search function.  
Refer to Playing moving images on page 24.  
2
Touch 10key to display the numeric  
keypad.  
Note  
3
Touch 0 to 9 corresponding to a menu  
You will return to normal playback if you change  
the viewing angle during fast forward/fast re-  
verse, pause or slow motion playback.  
number.  
4
Start playback from the selected part.  
Registering the numbers and start-  
ing playback.  
Return to the specified scene  
(Function for DVD video)  
45  
En  
 
Section  
14  
Detailed instructions  
Notes  
Note  
!
You can display the menu by touching Return  
during PBC playback. For details, refer to the  
instructions provided with the disc.  
PBC playback of a Video CD cannot be can-  
celed.  
During playback of Video CDs featuring PBC  
(playback control), you cannot select the re-  
peat play range or use the search function.  
If part of the recorded information does not dis-  
play, a scroll key appears on the right side of list.  
Touch the scroll key to scroll.  
!
!
Using sound retriever  
Automatically enhances compressed audio  
and restores rich sound.  
Off —  
!
Selecting tracks from the  
track title list  
is more effective than  
.
You can select tracks to playback using the  
track title list which is a list of the tracks re-  
corded on a disc.  
Changing audiobook speed  
(Function for iPod)  
!
Playback at a speed faster than  
1
Display the track title list.  
normal  
Refer to Playing audio on page 27.  
!
!
Playback at normal speed  
Playback at a speed slower than nor-  
2
Touch your favorite track title.  
mal  
Playback begins.  
Displaying lists related to  
the currently playing song  
(Link Search)  
Selecting files from the file  
name list  
(Function for compressed audio/DivX/JPEG/  
(Function for iPod)  
MPEG-1/MPEG-2/MPEG-4)  
File name list is a list of file names (or folder  
names) from which you can select a file (or  
folder) to play back.  
1
Start Link Search.  
1
Display the file (or folder) name list.  
2
Touch one of the categories in which  
Refer to Playing audio on page 27.  
you want to play.  
!
!
!
Artist Displays an album list of the artist  
currently being played.  
Album Displays a song list from the  
album currently being played.  
Genre Displays an album list from the  
genre currently being played.  
2
Touch your favorite file (or folder)  
name.  
#
When you have selected a folder, a list of the  
names of the files (or the folders) in it can be  
viewed. Repeat this operation to select the de-  
sired file name.  
#
To cancel searching, touch Cancel.  
3
Touch the title of the list that you want  
#
If folder 1 (ROOT) contains no files, playback  
to play.  
commences with folder 2.  
46  
En  
 
Section  
Detailed instructions  
14  
Note  
Capture an image in JPEG files  
You can capture image data and use it as wall-  
paper. Images can be stored and recalled ea-  
sily in this unit.  
If part of the recorded information does not dis-  
play, a scroll key appears on the right side of list.  
Touch the scroll key to scroll.  
!
Only one image can be stored on this unit.  
Old image is overwritten with the new one.  
â
Playing DivX VOD content  
1
Pause the slideshow when the desired  
Some DivX video on demand (VOD) content  
may only be playable a fixed number of times.  
When you load a disc containing this type of  
content, the number of times it has been  
played will be shown on-screen. You can then  
decide whether or not to play the disc.  
image is displayed.  
!
If there is no limit to the number of times  
the DivX VOD content can be viewed, then  
you may load the disc into your player and  
play the content as often as you like, and  
no message will be displayed.  
You can confirm the number of times that  
the content can be played by checking the  
number displayed after This DivX rental  
2
Capture the image.  
!
3
When Do you save this image?is dis-  
played, touch Yes.  
has used  
out of  
views..  
While storing the image to this unit, Saving  
the image. Dont switch off the battery.is  
displayed. When the process is finished,  
Image saved.is displayed.  
Important  
!
In order to play DivX VOD contents on this  
unit, you first need to register the unit with  
your DivX VOD contents provider. For details  
on your registration code, refer to Displaying  
the DivXâ VOD registration code on page 63.  
DivX VOD content is protected by a DRM (Di-  
gital Rights Management) system. This re-  
stricts playback of content to specific,  
registered devices.  
#
To cancel the storage process, touch No.  
Changing the wide screen  
mode  
You can select a desired mode for enlarging a  
4:3 picture to a 16:9 picture.  
!
%
If a message is displayed after loading  
1
Display the screen mode.  
a disc containing DivX VOD content, touch  
Play.  
Playback of the DivX VOD content will start.  
#
#
To skip to the next file, touch Next Play.  
If you do not want to play the DivX VOD con-  
tent, touch Stop.  
2
Touch the desired wide mode setting.  
47  
En  
 
Section  
14  
Detailed instructions  
Full (full screen)  
Selecting and playing the  
QuickMix/station list  
The 4:3 picture is enlarged in the horizontal direc-  
tion only, giving you a 4:3 TV picture (normal pic-  
ture) without any omissions.  
Touch the list for your Pandora stations to se-  
lect one of them to play.  
Just (just)  
1
Display the QuickMix/station list.  
The picture is enlarged slightly at the center and  
the amount of enlargement increases horizontally  
toward the edges of the screen, enabling you to  
enjoy a 4:3 picture without sensing any disparity  
even when viewing on a wide screen.  
2
Change the sort order.  
You can sort the items in the list al-  
phabetically.  
Cinema (cinema)  
The picture is enlarged by the same proportion as  
Full or Zoom in the horizontal direction and by  
an intermediate proportion between Full and  
Zoom in the vertical direction; ideal for a cinema-  
sized picture (wide screen picture) where cap-  
tions lie outside the picture.  
You can sort the items in the list in  
order of the dates on which the  
items were created.  
You can scroll the titles in the list  
while you touch and hold down the  
scroll icon.  
Zoom (zoom)  
The 4:3 picture is enlarged in the same proportion  
both vertically and horizontally; ideal for a cinema  
sized picture (wide screen picture).  
3
Select QuickMix or the desired station.  
You can play only one song at a time  
from a shuffled mix of several sta-  
tions.  
Normal (normal)  
The 4:3 picture is displayed as it is, giving you no  
sense of disparity since its proportions are the  
same as that of the normal picture.  
Notes  
Switching the XM/SIRIUS  
channel selection mode  
You have two methods for selecting a channel:  
by number and by category. When selecting  
by number, channels in any category can be  
selected. Select by category to narrow your  
search down to only channels in a particular  
category.  
!
!
You cannot operate this function while driving.  
Different settings can be stored for each video  
source.  
!
!
When a video is viewed in a wide screen mode  
that does not match its original aspect ratio, it  
may appear different.  
Remember that using the wide mode feature  
of this system for commercial or public view-  
ing purposes may constitute an infringement  
on the authors rights protected by the Copy-  
right Law.  
Mode All CH (channel number select setting)  
Mode Category (channel category select  
setting)  
!
The video image will appear coarser when  
viewed in Cinema or Zoom mode.  
48  
En  
 
Section  
Detailed instructions  
14  
Selecting a SIRIUS channel from  
a channel category  
Channels are organized into various program  
categories, e.g. Rock, Classic, Jazz while lis-  
tening to a SIRIUS station. You can specify  
channels by selecting the desired category.  
Selecting an XM/SIRIUS  
channel directly  
You can select an XM/SIRIUS channel directly  
by entering the desired channel number.  
1
Display the preset channel list.  
1
Select channel category selection  
mode.  
2
Switch to direct input display.  
Mode All CH (channel number select setting)  
Mode Category (channel category select  
setting)  
Switching to direct input display.  
3
Touch 0 to 9 to input the desired chan-  
2
Touch a or b to select the desired chan-  
nel number.  
#
nel category.  
To cancel the input numbers, touch C.  
3
Touch c or d on the buttons to select  
4
Select the XM/SIRIUS channel of the en-  
the desired channel in the selected channel  
category.  
tered number.  
The XM/SIRIUS channel of the entered num-  
ber is selected.  
Selecting a channel from the  
XM channel list display  
The list content can be switched so you can  
search for the track you want to listen to not  
only by the channel name but also by the artist  
name or song title.  
Selecting the XM/SIRIUS channel of  
the entered number.  
!
!
This function is available for GEX-P920XM.  
The channel list shows all the channels  
during Mode All CH mode, and the chan-  
nels included in the selected category dur-  
ing Mode Category mode.  
Using the Game Alert function  
This system can alert you when games invol-  
ving your favorite teams are about to start. To  
use this function you need to set up a game  
alert for the teams in advance.  
1
Display the preset channel list.  
!
This function is available for SIR-PNR2/SIR-  
PNR2C.  
2
Switch the channel list mode.  
Selecting teams for Game Alert  
1
Start Game Alert setup.  
Switching the channel list mode to  
the channel name or the artist  
name/song title.  
3
Touch the desired channel that you  
want to listen to.  
49  
En  
 
Section  
14  
Detailed instructions  
2
3
4
Select a desired league in League.  
Switching to the other station to lis-  
ten to the game.  
Switching the league name.  
Not tuning in to the other station.  
Select a desired team in Team.  
Displaying game information  
If any games of the selected teams are cur-  
rently playing, you can display information on  
the games and tune in to the broadcast chan-  
nel.  
Switching the team name.  
1
Display the game information for the  
selected team.  
Turn the alert on or off.  
Turning the alert on or off.  
2
Touch c or d to select a game.  
The game is displayed, followed by more de-  
tailed game information.  
The game alert function is activated for that  
team.  
!
The game score will be updated automati-  
#
When you have already selected 12 teams,  
cally.  
FULL is displayed and additional teams cannot  
be selected. In this case, first delete a selected  
team and then try again.  
3
Switch to the other station to listen to  
the game.  
5
Repeat these steps to select other  
Switching to the other station to lis-  
ten to the game.  
teams.  
Up to 12 teams can be selected.  
#
If you have not selected any teams, NOT SET  
is displayed.  
Switching the Game Alert on or off  
Once you select the teams, you need to turn  
the Game Alert function on.  
#
When games involving your favorite teams are  
not currently playing, NO GAME is displayed.  
The Game Alert function is on at the default  
setting.  
Displaying the Radio ID  
Channel number selection setting  
If you select CH000, the ID code is displayed.  
When a game of a selected  
team starts  
%
Select CH000.  
When a game of the selected team is about to  
start (or is currently playing) on a different sta-  
tion, a game alert is displayed.  
50  
En  
 
Section  
Detailed instructions  
14  
%
Pause and play  
Switching the SIRIUS display  
!
Actions will differ depending on the con-  
nected SIRIUS tuner.  
Playing and pausing.  
%
Touch SIRIUS tuner information to  
switch the SIRIUS display.  
Channel numberChannel nameCategory  
nameArtist nameSong title/Title name—  
Composer namePlay time  
Switching the seek mode  
There are two seek tuning settings, one is HD  
(Digital broadcasting stations seek) and the  
other is All (normal seek).  
Note  
Play time is displayed during the Instant Replay  
mode.  
AllHD  
Using the Instant Replay  
function  
The following functions can be operated in In-  
stant Replay mode.  
Switching the reception mode  
If the reception for a digital broadcast be-  
comes poor, this unit automatically switches  
to the analog broadcast of the same fre-  
quency. If this function is set to D/A Auto, the  
tuner switches between digital broadcast and  
analog broadcast automatically. If this func-  
tion is set to Analog, the tuner will only re-  
ceive analog broadcasts.  
!
!
To use this function, a Pioneer SIRIUS bus  
interface (e.g. CD-SB10) is required.  
To use this function, a SIRIUS plug-and-  
play unit with an Instant Replay Function is  
required.  
!
For details, refer to the SIRIUS plug-and-  
play units manuals.  
D/A AutoAnalog  
%
To exit from Instant Replay mode, se-  
lect another source or touch the following  
icon.  
Calling a number in the  
phone book  
Exiting from Instant Replay mode.  
(Function of AVH-P4400BH/AVH-P3400BH/  
AVH-P2400BT)  
The phone book in your cellular phone will be  
transferred automatically when the phone is  
connected to this unit.  
%
Select a track  
Press c or d (TRK).  
After finding the number you want to call in  
the phone book, you can select the entry and  
make the call.  
%
Fast forward or reverse  
Press and hold c or d (TRK).  
1
Switch to phone book mode.  
51  
En  
 
Section  
14  
Detailed instructions  
#
If you want to change the character to Rus-  
The phone book display appears.  
sian, touch the icon. To return to English, touch  
the icon again.  
2
Select the phone number list.  
The detailed phone number list of the selected  
entry is displayed.  
Changing the character to Russian.  
3
Select the phone number.  
#
If you want to store the phone number, touch  
#
The order of the first name and last name may  
and hold the list.  
be different from that of the cellular phone.  
4
Make the call.  
4
Touch the list to display the phone  
number list of the selected entry.  
If several phone numbers are included in an  
entry, select one by touching the list.  
If you want to switch to the call history list,  
touch the icon.  
#
5
End the call.  
#
Note  
Switching to the call history list.  
Depending on the cellular phone, the phone book  
may not be transferred automatically. In this  
case, operate your cellular phone to transfer the  
phone book. The visibility of this unit should be  
5
Make the call.  
6
End the call.  
Selecting a number by  
alphabet search mode  
(Function of AVH-P4400BH/AVH-P3400BH/  
AVH-P2400BT)  
Inverting names in phone  
book  
If a lot of numbers are registered in the phone  
book, you can search for the phone number by  
alphabet search mode.  
(Function of AVH-P4400BH/AVH-P3400BH/  
AVH-P2400BT)  
1
Switch to phone book mode.  
When your cellular phone is connected to this  
unit, the first and last names of your contacts  
may be registered to the phone book in reverse  
order. You can use this function to change the  
order back.  
The phone book display appears.  
2
Touch ABC to switch to alphabet search  
(Inverting the names in the phone book)  
mode.  
1
Switch to phone book mode.  
3
Touch the first letter of the entry you  
The phone book display appears.  
are looking for.  
The Phone Book entries starting with that let-  
ter (e.g. Ben, Brianand Burtwhen Bis  
selected) will be displayed.  
52  
En  
 
Section  
Detailed instructions  
14  
2
3
Invert names in phone books.  
3
Touch the list number to select a phone  
number.  
Name and phone number are displayed in the  
detailed list.  
#
Inverting names in phone books.  
If you want to store the phone number, touch  
Would you like to invert all names?”  
and hold the list.  
appears. Touch Yes to continue.  
While the names are inverted, is displayed.  
4
Make the call.  
#
If the inversion fails, Invert Name Errorap-  
pears. In such cases, try again from the begin-  
ning.  
5
End the call.  
Note  
Inverting the names of your contacts from this  
unit does not affect the data on your Bluetooth  
device.  
Using the missed, received  
and dialed call lists on the  
optional Bluetooth adapter  
Using the missed, received  
and dialed call lists  
(Function of AVH-P1400DVD)  
(Function of AVH-P4400BH/AVH-P3400BH/  
AVH-P2400BT)  
The 80 most recent calls dialed, received, and  
missed are stored in the memory. You can  
browse them and call numbers from these  
lists.  
The 80 most recent calls dialed, received, and  
missed are stored in the memory. You can  
browse them and call numbers from these  
lists.  
1
Switch to the call history list.  
1
Switch to the call history list.  
2
Touch a phone number or name (if en-  
tered) you want to call.  
2
Select Missed Calls, Dialed Calls or  
3
Make the call.  
Received Calls.  
Displaying the received call list.  
Displaying the dialed call list.  
Displaying the missed call list.  
4
End the call.  
Setting automatic answering  
If this function is on, this unit automatically  
answers all incoming calls.  
%
Turn automatic answering on or off.  
(AVH-P1400DVD)  
53  
En  
 
Section  
14  
Detailed instructions  
You can easily store up to six phone numbers  
as presets.  
(AVH-P4400BH/AVH-P3400BH/AVH-P2400BT)  
1
Display the preset screen.  
2
Touch one of preset dial keys to select  
the desired phone number.  
If you want to delete a preset phone number,  
touch and hold the preset dial key.  
Adjusting the other partys  
listening volume  
#
(Function of AVH-P4400BH/AVH-P3400BH/  
AVH-P2400BT)  
3
Make the call.  
To maintain the good sound quality, this unit  
can adjust the other partys listening volume.  
If the volume is not loud enough for the other  
party, use this function.  
4
End the call.  
%
Select Far-End VOL.  
123  
Making a call by entering  
phone number  
#
This function can be performed even while  
talking on the phone.  
Settings can be stored for each device.  
#
(Function of AVH-P4400BH/AVH-P3400BH/  
AVH-P2400BT)  
Wed 28 may  
12:45 PM  
1
Switching the ring tone  
You can select whether or not to use this  
units ring tone. If this function is set to on,  
the ring tone for this unit will sound.  
ABCDEHGHI 01  
012345678901  
1
4
7
2
5
8
0
3
6
9
Off  
#
*
C
+
1
Connect your cellular phone to this  
unit.  
Important  
2
Turn ring tone on or off.  
Be sure to park your vehicle in a safe place and  
apply the parking brake when performing this op-  
eration.  
(AVH-P1400DVD)  
(AVH-P4400BH/AVH-P3400BH/AVH-P2400BT)  
1
Switch to the entering phone number  
mode.  
2
Touch the number icons to input the  
numbers.  
Up to 24 digits can be entered.  
Using the preset dial lists  
(Function of AVH-P4400BH/AVH-P3400BH/  
#
AVH-P2400BT)  
54  
En  
 
Section  
Detailed instructions  
14  
3
Make the call.  
Registering a connected  
cellular phone  
(Function of AVH-P1400DVD)  
4
End the call.  
You can register a phone that is temporarily  
connected to this unit in order to take full ad-  
vantage of the features available with  
Bluetooth wireless technology. Only one cellu-  
lar phone can be registered.  
Note  
Entering phone number mode cannot be oper-  
ated unless a Bluetooth telephone is connected  
to this unit.  
1
Start registering a connected cellular  
phone.  
Setting the private mode  
(Function of AVH-P4400BH/AVH-P3400BH/  
AVH-P2400BT)  
During a conversation, you can switch to pri-  
vate mode (talk directly on your cellular  
phone).  
2
unit.  
Use cellular phone to register to this  
If registration is successful, the device name  
of the connected phone is displayed in the se-  
lected assignment.  
#
If the assignment is already taken, the device  
name will be displayed. To replace an assignment  
with a new phone, first delete the current assign-  
ment.  
#
If registration failed, the device name of the  
connected phone will not be displayed in the se-  
lected assignment. In such cases, return to step  
1 and try again.  
Using a cellular phone to  
initiate a connection  
(Function of AVH-P1400DVD)  
A Bluetooth wireless connection can be estab-  
lished from your phone by putting the unit into  
initiating a connection mode.  
You may need to refer to the operation manual  
that came with your phone if you are unsure  
how to initiate a connection from your phone.  
Voice recognition  
(Function of AVH-P1400DVD)  
If your cellular phone features voice recogni-  
tion technology, you can make a call by voice  
commands.  
1
Put the unit in initiating a connection  
!
Operation varies depending on the type of  
cellular phone. Refer to the instruction  
manual that came with your cellular phone  
for detailed instructions.  
mode.  
2
unit.  
#
lular phone.  
#
Use a cellular phone to connect to this  
1
Start voice recognition.  
Operation varies depending on the type of cel-  
2
Say the name of your contact aloud.  
You may need to enter the link code on your  
cellular phone to complete the connection.  
55  
En  
 
Section  
14  
Detailed instructions  
Connecting a Bluetooth  
audio player  
Displaying Bluetooth  
Device address  
(Function of AVH-P1400DVD)  
This unit displays its Bluetooth Device ad-  
dress.  
(Function of AVH-P1400DVD)  
A Bluetooth wireless connection can be estab-  
lished by putting the unit into initiating a con-  
nection mode.  
%
Touch Device Information to display de-  
%
mode.  
Put the unit in initiating a connection  
vice information.  
The Bluetooth Device address is displayed.  
This unit is now on standby for connection  
from Bluetooth audio player.  
If your Bluetooth audio player is set ready for  
Bluetooth wireless connection, connection to  
this unit is automatically established.  
Connecting to a Bluetooth  
device automatically  
(Function of AVH-P1400DVD)  
If this function is set to on, a connection be-  
tween your Bluetooth device and this unit will  
take place automatically as soon as the two  
devices are less than a few meters apart.  
Initially, this function is set to on.  
1
Touch Auto Connect to turn automatic  
connection on.  
If your Bluetooth device is ready for a  
Bluetooth wireless connection, a connection  
to this unit will automatically be established.  
#
To turn automatic connection off, touch  
Auto Connect again.  
2
Turn your vehicles ACC switch off and  
on.  
Once you turn your vehicles ACC switch on  
again, a connection is established auto-  
matically.  
56  
En  
 
Section  
Menu operations  
15  
Introduction of menu  
operations  
Audio adjustments  
Using fader/balance adjustment  
You can change the fader/balance setting to  
provide an ideal listening environment for all  
of the occupied seats.  
1 2  
Audio  
Fader/Balance  
Graphic EQ  
Auto EQ  
Sonic Center Control  
Loudness  
F/R 0 L/R  
0
Super Bass  
On  
L/R 0  
High  
1
Display the audio function menu.  
Subwoofer  
Off  
2
Touch Fader/Balance on the audio func-  
tion menu.  
34  
5
3
Touch a or b to adjust the front/rear  
1
Display menus.  
speaker balance.  
Range: Front 15 to Rear 15  
2
Touch any of the following touch panel  
#
Select F/R 0 L/R 0 when only using two  
keys to select the menu to be adjusted.  
speakers.  
#
The front/rear speaker balance cannot be ad-  
Touch panel keys  
justed when the rear output setting is  
Subwoofer. Refer to Setting the rear output and  
Video Setup menu  
1
2
3
Audio function menu  
4
Touch c or d to adjust the left/right  
speaker balance.  
Range: Left 15 to Right 15  
System menu  
Using the equalizer  
You can adjust the equalization to match the  
cars interior acoustic characteristics as de-  
sired.  
Favorite menu  
You can choose menus within  
each menu (Audio function  
menu, etc.) and register them  
to this favorite menu.  
4
Recalling equalizer curves  
There are seven stored equalizer curves which  
you can easily recall at any time. Here is a list  
of the equalizer curves.  
Returning to the current  
source display  
5
Notes  
Display  
Powerful  
Natural  
Vocal  
Equalizer curve  
Powerful  
Natural  
!
!
!
You can display the Video Setup menu when  
a Disc or USB source is selected.  
If you start the Video Setup menu, playback  
is stopped.  
You cannot display the Audio function menu  
when the mute function is on or a JPEG file is  
playing.  
Vocal  
Flat  
Flat  
Custom1  
Custom 1  
57  
En  
 
Section  
15  
Menu operations  
3
Touch c or d to select the desired item.  
Display  
Equalizer curve  
Custom 2  
PowerfulNaturalVocalFlatCustom1  
Custom2Super Bass  
Custom2  
Super Bass  
Super bass  
4
5
Touch the Equalizer band to adjust.  
!
!
!
The equalizer curves for Custom1 and  
Custom2 can be adjusted.  
You cannot select Custom1 and Custom2  
when using the auto-equalizer.  
When Flat, no changes are made to the  
sound. You can check the effects of the  
equalizer curves by switching alternatively  
between Flat and another equalizer curve.  
Touch a or b to adjust the level of the  
equalizer band.  
Range: +12dB to 12dB  
#
You can then select another band and adjust  
the level.  
Using the auto-equalizer  
The auto-equalizer is an equalizer curve cre-  
ated by auto EQ (refer to Auto EQ (auto-equaliz-  
You can turn the auto-equalizer on or off.  
If you connect an optional microphone to this  
unit, you can use this function.  
1
Display the audio function menu.  
2
Touch Graphic EQ on the audio function  
menu.  
#
You can select Graphic EQ when Auto EQ  
1
Display the audio function menu.  
function is off.  
3
Touch c or d to select the desired item.  
PowerfulNaturalVocalFlatCustom1  
Custom2Super Bass  
2
Touch Auto EQ to turn the auto-equali-  
zer on or off.  
You cannot use this function if auto EQ has  
#
Adjusting the 8-band graphic equalizer  
You can adjust the level of each band for the  
equalizer curves.  
not been carried out.  
Using sonic center control  
Sound that is suited for the listening position  
can easily be created with this function.  
!
A separate Custom1 curve can be created  
for each source. If you make adjustments  
when a curve other than Custom2 is se-  
lected, the equalizer curve settings will be  
stored in Custom1.  
A Custom2 curve that is common for all  
sources can be created. If you make adjust-  
ments when the Custom2 curve is se-  
lected, the Custom2 curve will be updated.  
1
Display the audio function menu.  
!
2
Touch Sonic Center Control on the  
audio function menu.  
1
Display the audio function menu.  
3
tion.  
Touch c or d to select a listening posi-  
Range: Left 7 to Right 7  
2
Touch Graphic EQ on the audio function  
menu.  
58  
En  
 
Section  
Menu operations  
Adjusting loudness  
15  
Boosting the bass  
Loudness compensates for deficiencies in the  
low-frequency and high-frequency ranges at  
low volume.  
You can boost the bass level.  
1
Display the audio function menu.  
1
Display the audio function menu.  
2
Touch c or d to select a desired level.  
Range: 0 to +6  
2
Touch Loudness on the audio function  
menu.  
Using the high pass filter  
3
Touch c or d to select a desired level.  
When you do not want low sounds from the  
subwoofer output frequency range to play  
from the front or rear speakers, turn on the  
HPF (high pass filter). Only frequencies higher  
than those in the selected range are output  
from the front or rear speakers.  
Off (off)Low (low)Mid (mid)High  
(high)  
Using subwoofer output  
This unit is equipped with a subwoofer output  
which can be turned on or off.  
1
Display the audio function menu.  
!
The cut-off frequency and output level can  
be adjusted when the subwoofer output is  
on.  
2
Touch c or d next to the frequency to  
1
Display the audio function menu.  
select cut-off frequency.  
Off (off)50Hz63Hz80Hz100Hz—  
125Hz  
Only frequencies higher than those in the se-  
lected range are output from the front or rear  
speakers.  
2
Touch Subwoofer on the audio function  
menu.  
3
Touch On or Off next to Subwoofer to  
turn the subwoofer output on or off.  
Adjusting source levels  
With SLA (source level adjustment), the vo-  
lume levels of each source can be adjusted to  
prevent significant differences between  
sources.  
4
Touch Normal or Reverse next to Phase  
to select the phase of subwoofer output.  
5
Touch c or d next to Level to adjust  
the output level of the subwoofer.  
Range: +6 to 24  
!
Settings are based on the FM volume level,  
which remains unchanged.  
6
Touch c or d next to Frequency to se-  
1
Display the audio function menu.  
lect the cut-off frequency.  
50Hz63Hz80Hz100Hz125Hz  
Only frequencies lower than those in the se-  
lected range are outputted from the subwoo-  
fer.  
2
Compare the FM volume level with the  
level of the source you wish to adjust.  
59  
En  
 
Section  
15  
Menu operations  
3
Touch Source Level Adjuster on the  
Setting up the DVD player  
Setting the subtitle language  
You can set a desired subtitle language. When  
available, the subtitles will be displayed in the  
selected language.  
audio function menu.  
4
Touch a or b to adjust the source vo-  
lume.  
Range: +4 to 4  
Notes  
1
Display the Video Setup menu.  
!
!
!
When selecting FM as the source, you cannot  
switch to Source Level Adjuster.  
The AM volume level can also be adjusted  
with this function.  
Video CD, CD, compressed audio, DivX,  
MPEG-1, MPEG-2 and MPEG-4 are automati-  
cally set to the same source level adjustment  
volume.  
2
Touch Subtitle Language on the  
Video Setup menu.  
A subtitle language menu is displayed.  
3
Touch the desired language.  
The subtitle language is set.  
If you have selected Others, refer to When you  
!
!
iPod and USB storage device are automati-  
cally set to the same source level adjustment  
volume.  
External unit 1 and external unit 2 are automa-  
tically set to the same source level adjustment  
volume.  
#
Notes  
!
If the selected language is not available, the  
language specified on the disc is displayed.  
You can also switch the subtitle language by  
touching the icon during playback. (Refer to  
Playing moving images on page 24.)  
!
!
The setting made here will not be affected  
even if the subtitle language is switched dur-  
ing playback using Subtitle.  
When you select Others  
A language code input display is shown when  
Others is selected. Refer to Language code  
%
Touch 0 to 9 to input the language  
code.  
#
#
To cancel the entered numbers, touch C.  
To register the code, touch the following touch  
panel key.  
Registering the code.  
Setting the audio language  
You can set the preferred audio language.  
60  
En  
 
Section  
Menu operations  
15  
1
Display the Video Setup menu.  
Setting the multi-angle DVD  
display  
The angle icon can be set so it appears on  
scenes where the angle can be switched.  
2
Touch Audio Language on the Video  
Setup menu.  
An audio language menu is displayed.  
1
Display the Video Setup menu.  
3
Touch the desired language.  
The audio language is set.  
If you have selected Others, refer to When you  
2
Touch Multi Angle on the Video Setup  
#
menu to turn angle icon display on or off.  
Notes  
Setting the aspect ratio  
!
If the selected language is not available, the  
language specified on the disc is used.  
You can also switch the audio language by  
touching Audio during playback. (Refer to  
Playing moving images on page 24.)  
The setting made here will not be affected  
even if the audio language is switched during  
playback using Audio.  
There are two kinds of display: a wide screen  
display that has a width-to-height ratio (TV as-  
pect ratio) of 16:9, and regular display that has  
a TV aspect of 4:3. Be sure to select the correct  
TV aspect for the display connected to V OUT.  
!
!
!
When using regular display, select either  
Letter Box or Pan Scan. Selecting 16:9  
may result in an unnatural picture.  
!
If you select the TV aspect ratio, the units  
display will change to the same setting.  
Setting the menu language  
You can set the preferred language in which  
the menus recorded on a disc are displayed.  
1
Display the Video Setup menu.  
1
Display the Video Setup menu.  
2
Touch TV Aspect on the Video Setup  
menu to select the TV aspect ratio.  
Touch TV Aspect repeatedly until the desired  
aspect ratio appears.  
2
Touch Menu Language on the  
Video Setup menu.  
A menu language menu is displayed.  
!
16:9 Wide screen picture (16:9) is dis-  
played as is (initial setting)  
3
Touch the desired language.  
The menu language is set.  
If you have selected Others, refer to When you  
!
Letter Box The picture is the shape of a  
letterbox with black bands on the top and  
bottom of the screen  
#
!
Pan Scan The picture is cut short on the  
right and left sides of the screen  
Note  
Notes  
When playing discs that do not specify  
If the selected language is not available, the lan-  
guage specified on the disc is displayed.  
!
Pan Scan, the disc is played back in  
Letter Box display even if you select the  
Pan Scan setting. Confirm whether the disc  
16 : 9 LB  
package bears the  
mark.  
61  
En  
 
Section  
15  
Menu operations  
!
The TV aspect ratio cannot be changed for  
some discs. For details, refer to the discs in-  
structions.  
2
Touch Parental on the Video Setup  
menu.  
3
Touch 0 to 9 to input a four digit code  
number.  
Setting the slideshow interval  
JPEG files can be viewed as a slideshow on  
this unit. In this setting, the interval between  
each image can be set.  
#
#
To cancel the entered numbers, touch C.  
To register the code, touch the following touch  
panel key.  
Registering the code.  
1
Display the Video Setup menu.  
The code number is set, and the level can now be  
set.  
2
Touch Time Per Photo Slide on the  
Video Setup menu to select the slideshow  
interval.  
Touch Time Per Photo Slide repeatedly until  
the desired setting appears.  
4
5
Touch 1 to 8 to select the desired level.  
Touch Enter.  
The parental lock level is set.  
!
!
!
8 Playback of the entire disc is possible  
(initial setting)  
7 to 2 Playback of discs for children and  
non-adult-oriented discs is possible  
1 Playback of discs for children only is  
possible  
!
!
!
!
5sec JPEG images switch at intervals of 5  
seconds  
10sec JPEG images switch at intervals of  
10 seconds  
15sec JPEG images switch at intervals of  
15 seconds  
Manual JPEG images can be switched  
manually  
Notes  
!
We recommend to keep a record of your code  
number in case you forget it.  
Setting parental lock  
!
The parental lock level is stored on the disc.  
Look for the level indication written on the  
disc package, included literature or on the  
disc itself. Parental lock of this unit is not pos-  
sible if a parental lock level is not stored on  
the disc.  
With some discs, the parental lock may be ac-  
tive only for certain levels of scenes. The play-  
back of those scenes will be skipped. For  
details, refer to the instruction manual that  
came with the disc.  
Some DVD video discs let you use parental  
lock to restrict children from viewing violent  
and adult-oriented scenes. You can set paren-  
tal lock to the desired level.  
!
When you have a parental lock level set  
and play a disc featuring parental lock,  
code number input indications may be dis-  
played. In such cases, playback will begin  
when the correct code number is entered.  
!
Setting the code number and level  
A code number must be registered in order to  
play back discs with parental lock.  
Changing the level  
You can change the set parental lock level.  
1
Display the Video Setup menu.  
1
Display the Video Setup menu.  
62  
En  
 
Section  
Menu operations  
15  
!
Up to 126 characters can be displayed on one  
screen. If more than 126 characters are set,  
the excess characters will not be displayed.  
2
Touch Parental on the Video Setup  
menu.  
3
Touch 0 to 9 to input the registered  
code number.  
â
Displaying the DivX VOD  
registration code  
#
To register the code, touch the following touch  
panel key.  
In order to play DivX VOD (video on demand)  
contents on this unit, the unit must first be re-  
gistered with a DivX VOD contents provider.  
For registration, generate a DivX VOD registra-  
tion code and submit it to your provider.  
Registering the code.  
This sets the code number, and the level can now  
be changed.  
If you enter an incorrect code number, the  
icon is displayed. Touch C and enter the correct  
!
Keep a record of the code as you will need  
it when you register your unit to the DivX  
VOD provider.  
#
code number.  
1
Display the Video Setup menu.  
4
5
Touch 1 to 8 to select the desired level.  
Touch Enter.  
The new parental lock level is set.  
If you forget your code number, touch C 10  
times.  
2
Touch DivX® VOD on the Video Setup  
#
menu.  
Registration Code and Deregistration Code  
appear.  
Setting the DivX subtitle file  
3
Touch Registration Code.  
You can select whether or not to display DivX  
external subtitles.  
Your registration code is displayed.  
!
The DivX subtitles will be displayed even  
when Custom is selected if no DivX exter-  
nal subtitle files exist.  
Displaying the deregistration code  
If your device is already registered, deregister  
it by entering the deregistration code.  
1
Display the Video Setup menu.  
1
Display the Video Setup menu.  
2
Touch DivX® Subtitle on the  
2
Touch DivX® VOD on the Video Setup  
Video Setup menu to select the desired  
subtitle setting.  
menu.  
!
!
Original Display the DivX subtitles  
Custom Display the DivX external subti-  
tles  
3
#
Touch Deregistration Code.  
To cancel deregistration, touch Cancel.  
4
Touch OK.  
Notes  
Up to 42 characters can be displayed on one  
The deregistration is complete.  
!
line. If more than 42 characters are set, the  
line breaks and the characters are displayed  
on the next line.  
63  
En  
 
Section  
15  
Menu operations  
Automatic playback of DVDs  
System settings  
Switching the auxiliary setting  
Activate this setting when using an auxiliary  
device connected to this unit.  
When a DVD disc with a DVD menu is in-  
serted, this unit will cancel the menu automa-  
tically and start playback from the first chapter  
of the first title.  
!
Some DVDs may not operate properly. If  
this function is not fully operated, turn this  
function off and start playback.  
1
Display the system menu.  
1
Display the Video Setup menu.  
2
Touch AUX Input on the system menu  
to turn AUX Input on or off.  
2
Touch DVD Auto Play to turn automatic  
playback on.  
To turn automatic playback off, touch  
Setting AV input  
Activate this setting when using an external  
video component connected to this unit.  
#
DVD Auto Play again.  
1
Display the system menu.  
2
Touch AV Input on the system menu to  
turn AV Input on or off.  
Setting the rear output and  
subwoofer controller  
This units rear output (rear speaker leads out-  
put and RCA rear output) can be used for full-  
range speaker (Full) or subwoofer  
(Subwoofer) connection. If you switch the  
rear output setting to Subwoofer, you can  
connect a rear speaker lead directly to a sub-  
woofer without using an auxiliary amp.  
Initially, the unit is set for a rear full-range  
speaker connection (Full).  
1
Turn the unit off.  
2
Press HOME to switch to the HOME dis-  
play.  
3
Touch System key.  
System menu is displayed.  
64  
En  
 
Section  
Menu operations  
15  
!
!
When ATT is displayed, the sound is attenu-  
ated and only the volume can be adjusted.  
(No other audio adjustments can be made.)  
Operation returns to normal when the phone  
connection is ended.  
4
Touch Rear Speaker on the system  
menu to switch the subwoofer output or  
full-range speaker.  
#
When no subwoofer is connected to the rear  
output, select Full (full-range speaker).  
When a subwoofer is connected to the rear  
#
output, select Subwoofer (subwoofer).  
Selecting the system language  
The system language can be selected from  
nine languages.  
If text information such as the title name, artist  
name or a comment is embedded in a Eur-  
opean language, they can also be displayed  
on this unit.  
Notes  
!
!
Even if you change this setting, there will be  
no output unless you turn the subwoofer out-  
Both rear speaker lead outputs and RCA rear  
output are switched simultaneously in this  
setting.  
!
The language can be changed for the fol-  
lowing:  
System menu  
On-screen display  
Switching sound muting/  
attenuation  
Sound from this system is automatically  
muted or attenuated when a signal from  
equipment with a mute function is received.  
(English and Russian only)  
Multi language setting for DivX  
(English and Russian only)  
Language for cautions  
Some operations on this unit are prohib-  
ited from use while driving or require  
careful attention when operated. In  
such cases, a caution will appear on the  
display. You can change the language  
for caution messages with this setting.  
If the embedded language and the selected  
language setting are not the same, text in-  
formation may not display properly.  
Some characters may not be displayed  
properly.  
!
Sound from this system returns to normal  
when the muting or attenuation is can-  
celed.  
1
Display the system menu.  
!
2
Touch Mute/ATT until the desired set-  
!
ting appears.  
Touch Mute/ATT until the desired setting ap-  
pears in the display.  
1
Display the system menu.  
!
!
Mute Muting  
ATT 20dB Attenuation (ATT 20dB has a  
stronger effect than ATT 10dB)  
ATT 10dB Attenuation  
Off Turns the sound muting/attenuation  
off  
2
Touch System Language on the system  
menu to select the desired language.  
!
!
3
Touch the desired language.  
English (English)Français (French)—  
Deutsch (German)Español (Spanish)  
Русский (Russian)Português (Portu-  
Notes  
When Mute is displayed, the sound is turned  
off and no audio adjustments can be made.  
!
guese)
ﺍﻟﻌﺮﺑﻴﺔ
 (Arabic)—  
(Hebrew)  
(Persian)  
65  
En  
Section  
15  
Menu operations  
5
Touch Clear.  
Setting the ever scroll  
After selecting a desired item, a confirmation  
display appears. Touch OK to delete the mem-  
ory.  
When ever scroll is set to On, recorded text in-  
formation scrolls continuously in the display.  
Set to Off if you prefer the information to  
scroll just once.  
#
If you do not want to clear the memory, touch  
Cancel.  
1
Display the system menu.  
Updating Bluetooth connection  
software  
(Function of AVH-P4400BH/AVH-P3400BH/  
AVH-P2400BT)  
2
Touch Ever Scroll on the system menu  
to turn ever scroll on or off.  
This function is used to update this unit with  
the latest software. For information on the soft-  
ware and updating, refer to our website.  
Setting the Bluetooth audio  
(Function of AVH-P4400BH/AVH-P3400BH/  
AVH-P2400BT)  
Important  
You need to activate the Audio source in order  
to use a Bluetooth audio player.  
Never turn the unit off and never disconnect the  
phone while the software is being updated.  
1
Display the system menu.  
1
Turn the unit off.  
2
play.  
Press HOME to switch to the HOME dis-  
2
Touch Bluetooth Audio on the system  
menu to turn Bluetooth audio on or off.  
3
Touch System key.  
System menu is displayed.  
Clearing Bluetooth memory  
(Function of AVH-P4400BH/AVH-P3400BH/  
AVH-P2400BT)  
4
Touch Bluetooth Software Update.  
5
Touch Start to display the data transfer  
mode.  
Important  
#
Follow the on-screen instructions to finish up-  
Never turn the unit off while the Bluetooth mem-  
ory is being cleared.  
dating the software.  
1
Turn the unit off.  
Displaying the Bluetooth  
system version  
(Function of AVH-P4400BH/AVH-P3400BH/  
AVH-P2400BT)  
2
play.  
Press HOME to switch to the HOME dis-  
If this unit fails to operate properly, you may  
need to consult your dealer for repair. In such  
cases, you may be asked to specify the system  
version. Perform the following procedure to  
check the version on this unit.  
3
Touch System key.  
System menu is displayed.  
4
Touch Bluetooth Memory Clear on the  
system menu.  
66  
En  
Section  
Menu operations  
15  
1
Turn the unit off.  
1
Display the system menu.  
2
Press HOME to switch to the HOME dis-  
play.  
2
Touch Camera Polarity on the system  
menu to select the appropriate setting.  
3
Touch System key.  
!
!
Battery When the polarity of the con-  
nected lead is positive while the shift lever  
is in REVERSE (R) position  
Ground When the polarity of the con-  
nected lead is negative while the shift lever  
is in REVERSE (R) position  
System menu is displayed.  
4
Touch Bluetooth Version Information to  
display to the version of the Bluetooth  
module of this unit.  
!
Off When a rear view camera is not con-  
nected to this unit  
Setting the rear view camera  
(back up camera)  
Note  
You can also switch the rear view image by press-  
ing the touch key, regardless of the  
Camera Polarity setting on the sytem menu.  
CAUTION  
Pioneer recommends the use of a camera  
which outputs mirror-reversed images.  
Otherwise, the screen image will appear re-  
versed.  
Setting the video signal  
When you connect this unit to an AV equip-  
ment to this unit, select the suitable video sig-  
nal setting.  
This unit features a function that automatically  
switches to the rear view camera video (R.C  
IN) when a rear view camera is installed on  
your car and the shift lever is moved to the RE-  
VERSE (R) position. (For more details, con-  
sult your dealer.)  
!
As this function is initially set to Auto, the  
unit will automatically adjust the video sig-  
nal setting.  
!
After you set up the rear view camera set-  
ting, move the shift lever to REVERSE (R)  
and confirm that the rear view camera  
video is shown on the display.  
!
You can operate this function only for the  
video signal input into the AV input.  
1
Display the system menu.  
!
!
!
Change this setting if the display switches  
to the rear view camera video by error while  
you are driving forward.  
To stop watching the rear view camera  
video and return to the source display,  
press and hold MUTE.  
Touch the RearView source icon to display  
the rear view camera image while driving.  
Touch the source icon again to turn the  
rear view camera off. For details, refer to Se-  
2
Touch Video Signal Setting on the func-  
tion menu.  
Video Signal Setting items are displayed.  
!
!
!
AV Adjusts the AV video signal  
AUX Adjusts the AUX video signal  
Camera Adjusts the rear view camera  
video signal  
3
Touch c or d to select the desired  
video signal appears.  
AutoPALNTSCPAL-MPAL-N—  
SECAM  
67  
En  
 
Section  
15  
Menu operations  
#
You cannot adjust the picture adjustment for  
Changing the picture adjustment  
the rear view camera when Camera Polarity is  
set to Off. (Refer to Setting the rear view camera  
You can adjust the Brightness (brightness),  
Contrast (contrast), Color (color) , Hue (hue),  
Dimmer (dimmer), Temperature (tempera-  
ture), Black Level (black level) and  
Dot Adjustment (RGB dot clock adjustment)  
for each source and rear view camera.  
#
You can adjust Hue only when the color sys-  
tem is set to NTSC.  
With some rear view cameras, picture adjust-  
ment may not be possible.  
#
!
You cannot adjust Color, Hue, Contrast  
and Black Level for the audio source.  
4
Touch c or d to adjust the selected  
item.  
1
Display the system menu.  
Each time you touch c or d, the level of the  
selected item increases or decreases.  
#
#
Dimmer can be adjusted from +1 to +48.  
Temperature can be adjusted from +3 to 3.  
2
If you are adjusting the  
Picture Adjustment, select the unit.  
5
Touch Black Level and Dot Adjustment  
to adjust.  
Adjusting the Picture Adjustment  
for the Navigation system.  
#
#
Black Level can be set on or off.  
Dot Adjustment can be set to 1 or 2.  
NAVI  
Notes  
Rear  
View  
Adjusting the Picture Adjustment  
for the rear view camera.  
!
!
You cannot operate this function while driving.  
Different Brightness/Contrast/Dimmer set-  
tings can be set for when the illumination  
switch is on and when it is off.  
Adjusting the Picture Adjustment  
for the source.  
Source  
Auto EQ (auto-equalizing)  
3
Touch any of the following touch panel  
The auto-equalizer automatically measures  
the cars interior acoustic characteristics, and  
then creates an auto-equalizer curve based on  
that information.  
keys to select the function to be adjusted.  
Picture Adjustment items are displayed.  
!
!
!
!
Brightness Adjusts the black intensity  
Contrast Adjusts the contrast  
Color Adjusts the color saturation  
Hue Adjusts the tone of color (red or  
green is emphasized)  
!
To perform this function, dedicated micro-  
phone (e.g. CD-MC20) is required.  
!
!
!
Dimmer Adjusts the brightness of the dis-  
play  
WARNING  
As a loud tone (noise) may be emitted from the  
speakers when measuring the car's interior  
acoustic characteristics, never perform auto TA  
or auto EQ while driving.  
Temperature Adjusts the color tempera-  
ture, resulting in a better white balance  
Black Level Emphasizes the dark portions  
of images making the difference between  
bright and dark more distinct  
Dot Adjustment Adjusts phase shifting  
by dot clock when a Navigation system is  
connected  
CAUTION  
!
!
Thoroughly check the conditions before per-  
forming auto EQ as the speakers may be da-  
maged if these functions are performed when:  
68  
En  
 
Section  
Menu operations  
15  
The speakers are incorrectly connected.  
(For example, when a rear speaker is con-  
nected as a subwoofer output.)  
A speaker is connected to a power amp de-  
livering output higher than the speakers  
maximum input power capability.  
If the microphone is placed in an unsuitable  
position the measurement tone may become  
loud and measurement may take a long time,  
resulting in battery drainage. Be sure to place  
the microphone in the specified location.  
The LPF on active subwoofers or exter-  
nal amps delay the lower sounds.  
Auto EQ changes the audio settings as fol-  
lows:  
The fader/balance settings return to the  
center position. (Refer to Using fader/  
The equalizer curve switches to Flat.  
The front, center and rear speakers will  
automatically be adjusted to a high  
pass filter setting.  
Previous settings for auto EQ will be over-  
written.  
!
!
Before operating the auto EQ function  
!
!
Carry out auto EQ in as quiet a place as  
possible, with the car engine and air condi-  
tioning switched off. Also cut power to car  
phones or portable telephones in the car, or  
remove them from the car before carrying  
out auto EQ. Sounds other than the mea-  
surement tone (surrounding sounds, en-  
gine sound, telephones ringing etc.) may  
prevent correct measurement of the car in-  
terior acoustic characteristics.  
Performing auto EQ  
Stop the car in a place that is quiet,  
close all the doors, windows and sun roof,  
and then turn the engine off.  
If the engine is left running, engine noise may  
prevent correct auto EQ.  
1
2
Fix the optional microphone in the cen-  
!
Be sure to carry out auto EQ using the op-  
tional microphone. Using another micro-  
phone may prevent measurement, or result  
in incorrect measurement of the car inter-  
ior acoustic characteristics.  
ter of the headrest of the drivers seat, fa-  
cing forward.  
The auto EQ may differ depending on where  
you place the microphone. If desired, place  
the microphone on the front passenger seat to  
carry out auto EQ.  
!
!
In order to perform auto EQ, the front  
speaker must be connected.  
When this unit is connected to a power  
amp with input level control, auto EQ may  
not be possible if the power amps input  
level is set below the standard level.  
When this unit is connected to a power  
amp with an LPF, turn this LPF off before  
performing auto EQ. Also set the cut-off fre-  
quency for the built-in LPF of an active sub-  
woofer to the highest frequency.  
The distance has been calculated by com-  
puter to be the optimum delay to give accu-  
rate results for the circumstances, so  
please continue to use this value.  
!
!
3
Turn the ignition switch to ON or ACC.  
If the cars air conditioner or heater is turned  
on, turn it off. Noise from the fan in the air  
conditioner or heater may prevent correct auto  
EQ.  
The reflected sound within the car is  
strong and delays occur.  
69  
En  
Section  
15  
Menu operations  
4
Display the system menu.  
9
Store the microphone carefully in the  
glove compartment or another safe place.  
If the microphone is subjected to direct sun-  
light for an extended period, high tempera-  
tures may cause distortion, color change or  
malfunction.  
5
Touch Auto EQ Measurement to enter  
auto EQ measurement mode.  
6
Plug the microphone into the micro-  
10 Press h(eject) to close the panel.  
(AVH-P4400BH only)  
phone input jack on this unit.  
(AVH-P3400BH/AVH-P2400BT/AVH-  
P1400DVD)  
(AVH-P4400BH)  
7
8
Touch Start to start auto EQ.  
When the 10-second countdown starts,  
get out of the car and close the door within  
10 seconds.  
A measurement tone (noise) is emitted from  
the speakers, and auto EQ measurement be-  
gins.  
When auto EQ is completed, Complete is dis-  
played.  
When the cars interior acoustic characteris-  
tics cannot be measured correctly, an error  
message will be displayed. (Refer to Under-  
#
It takes about nine minutes for auto EQ mea-  
surement to be completed when all the speakers  
are connected.  
#
To stop auto EQ, touch Stop.  
70  
En  
Section  
Menu operations  
Favorite menu  
15  
Introduction of Bluetooth  
connection menu operations  
1
Display menu columns to register.  
#
If you are using a cellular phone that can be  
connected via Bluetooth wireless technology,  
we recommend that you use your phone to  
search for this unit and establish a connection  
between it and your phone. The PIN code is  
set to 0000 as default. The product name for  
this unit will display on your phone as the de-  
vice name. For details, refer to Entering PIN  
73. For further details concerning the proce-  
dures for establishing Bluetooth wireless con-  
nections, refer to the instruction manual for  
the phone.  
You can customize menus except  
Video Setup menu.  
2
Touch and hold the menu column to  
register it.  
#
menu column again.  
To cancel registration, touch and hold the  
3
Display the favorite menu and choose a  
registered menu.  
Note  
You can register up to 12 columns.  
Pairing from this unit  
(Function of AVH-P4400BH/AVH-P3400BH/  
AVH-P2400BT)  
Connection  
01: Phone1  
02: Phone2  
03: Phone3  
1
Display the Bluetooth Connection  
Menu.  
2
3
Touch Connection to select a device.  
Start to search.  
Starting to search.  
While searching,  
is displayed and when  
available devices are found, the device names  
or Bluetooth device addresses (if names can-  
not be obtained) are displayed.  
71  
En  
 
Section  
15  
Menu operations  
#
If you want to switch between the device  
If you cannot open the connection between  
your Bluetooth device and this unit from your  
Bluetooth device, you can use this function to  
establish a connection.  
names and Bluetooth device addresses, touch  
the icon.  
Switching between the device  
names and Bluetooth device ad-  
dresses.  
1
Display the Bluetooth Connection  
Menu.  
#
#
To cancel searching, touch Stop.  
If five devices are already paired,  
Memory Full is displayed and pairing cannot be  
performed. In such cases, delete a paired device  
first. Refer to this page.  
2
Touch Special Device to select the spe-  
cial device.  
#
Bluetooth devices that are difficult to establish  
#
If no device can be found, Not Found is dis-  
a connection with are called special devices. If  
your Bluetooth device is listed as a special device,  
select the appropriate one.  
played. In such cases, check the status of the  
Bluetooth device and search again.  
4
Touch a device name to select the de-  
3
Touch the special device list to open the  
vice you want to connect to.  
While connecting, Pairing is displayed. If the  
connection is established, Paired is displayed.  
connection.  
This unit is now on standby for a connection  
with the Bluetooth device.  
!
6-digit number appears on the display of  
this unit. Once the connection is estab-  
lished, this number disappears.  
#
If three devices are already paired,  
Memory Full is displayed and pairing cannot be  
performed. In such cases, delete a paired device  
first. Refer to this page.  
#
If the connection fails, Error is displayed. In  
such cases, try again from the beginning.  
The PIN code is set to 0000 as the default, but  
4
Use your Bluetooth device to establish  
#
a connection.  
can be changed. Refer to Entering PIN code for  
The connection method is different depending  
on the Bluetooth device. Refer to the manual  
for your Bluetooth device to establish a con-  
nection.  
#
Once the connection is established, the de-  
vice name is displayed.  
Touch the device name to disconnect.  
While connecting, Pair your phone is dis-  
played. If the connection is established,  
Paired is displayed.  
#
If you want to delete a paired Bluetooth tele-  
phone, display Delete OK?. Touch Yes to delete  
the device.  
#
If the connection fails, Error is displayed. In  
such cases, try again from the beginning.  
You may also need to enter a PIN code into  
#
Deleting a paired device.  
this unit. If your telephone requires a PIN code to  
establish a connection, look for the code on the  
telephone or in its accompanying documenta-  
tion.  
#
Never turn the unit off while the paired  
Bluetooth telephone is being deleted.  
#
The PIN code is set to 0000 as the default, but  
can be changed. Refer to Entering PIN code for  
Using a Bluetooth device to pair  
(Function of AVH-P4400BH/AVH-P3400BH/  
AVH-P2400BT)  
72  
En  
 
Section  
Menu operations  
15  
Connecting to a Bluetooth  
device automatically  
Displaying Bluetooth Device  
address  
(Function of AVH-P4400BH/AVH-P3400BH/  
AVH-P2400BT)  
(Function of AVH-P4400BH/AVH-P3400BH/  
AVH-P2400BT)  
If this function is set to on, a connection be-  
tween your Bluetooth device and this unit will  
take place automatically as soon as the two  
devices are less than a few meters apart.  
Initially, this function is set to on.  
This unit displays its Bluetooth device ad-  
dress.  
1
Display the Bluetooth Connection  
Menu.  
1
Display the Bluetooth Connection  
Menu.  
2
Touch Device Information to display de-  
vice information.  
The Bluetooth device address is displayed.  
2
Touch Auto Connect to turn automatic  
connection on.  
Entering PIN code for Bluetooth  
wireless connection  
(Function of AVH-P4400BH/AVH-P3400BH/  
AVH-P2400BT)  
To connect your Bluetooth device to this unit  
via Bluetooth wireless technology, you need to  
enter a PIN code on your Bluetooth device to  
verify the connection. The default code is  
0000, but you can change it with this function.  
If your Bluetooth device is ready for a  
Bluetooth wireless connection, a connection  
to this unit will automatically be established.  
#
To turn automatic connection off, touch  
Auto Connect again.  
If connection fails, Auto connection failed.  
Retry?appears. Touch Yes to reconnect.  
3
Once you turn your vehicles ACC  
switch on again, a connection is estab-  
lished automatically.  
1
Display the Bluetooth Connection  
Menu.  
Switching visible unit  
(Function of AVH-P4400BH/AVH-P3400BH/  
AVH-P2400BT)  
This function sets whether or not to make this  
unit visible to the other device.  
Initially, this function is set to on.  
2
Touch PIN Code Input to select  
PIN Code Input.  
3
4
Touch 0 to 9 to input pin code.  
After inputting PIN code (up to 8 di-  
1
Display the Bluetooth Connection  
gits), store in this unit.  
Menu.  
Storing the PIN code in this unit.  
2
Touch Visibility to select visibility off.  
#
To turn visibility on, touch Visibility again.  
73  
En  
 
Section  
15  
Menu operations  
Selecting the OSD (on-screen  
display) color  
The OSD color can be changed.  
Introduction of Theme  
setting menu operations  
1
Display the Theme menu.  
Selecting the illumination color  
This unit is equipped with multiple-color illu-  
mination.  
2
3
Touch Screen.  
Touch one of the colors on the list.  
Direct selection from preset  
illumination colors  
You can select an illumination color from the  
color list.  
Selecting the background display  
You can switch the background that is dis-  
played when listening to a source.  
1
Display the Theme menu.  
1
Display the Theme menu.  
2
Touch Background.  
2
Touch Illumination and then touch a  
color on the list.  
3
Touch the desired setting.  
#
If no JPEG images are stored in this unit, you  
cannot select photo. To store a JPEG image to  
Customizing the illumination color  
1
Display the Theme menu.  
2
Touch Illumination and then touch  
Custom.  
3
Display the customizing menu.  
Displaying the customizing menu.  
4
Touch the color bar to customize the  
color.  
5
Touch c or d to fine-tune the color.  
6
Touch the icon and hold to store the  
customized color in the memory.  
Storing the customized color in  
the memory.  
Memo  
The customized color has been stored in the  
memory.  
The set color will be recalled from the memory  
the next time you touch the same icon.  
74  
En  
 
Section  
Other functions  
16  
6
Gently touch the center of the + mark  
Adjusting the response  
positions of the touch panels  
(Touch Panel Calibration)  
If you feel that the touch panel keys on the  
screen deviate from the actual positions that  
respond to your touch, adjust the response po-  
sitions of the touch panel. There are two ad-  
justment methods: 4-point adjustment, in  
which you touch four corners of the screen;  
and 16-point adjustment, in which you make  
fine-adjustments on the entire screen.  
displayed on the screen.  
After you touch all the marks, the data for the  
adjusted position is saved.  
#
Do not turn off the engine while the data is  
being saved.  
7
Press and hold HOME to complete the  
adjustment.  
Using an AUX source  
!
Touch the screen gently for adjustment.  
Forcefully pressing the touch panel may da-  
mage the touch panel. Do not use a sharp  
pointed tool such as a ballpoint pen or me-  
chanical pen. Doing so may damage the  
screen.  
A separately sold auxiliary device such as a  
VCR or portable device can be connected to  
this unit. When connected, the auxiliary device  
is automatically recognized as an AUX source  
and is assigned to AUX.  
!
If the touch panel cannot be adjusted prop-  
erly, consult your local Pioneer dealer.  
About AUX connection methods  
You can connect auxiliary devices to this unit.  
1
Turn the unit off.  
Mini pin plug cable (AUX)  
When connecting an auxiliary device using a  
mini plug cable  
iPods and portable audio/video players can be  
connected to this unit via mini plug cable.  
2
Press and hold HOME to start Touch  
Panel Calibration.  
The 4-point touch panel adjustment screen ap-  
pears.  
!
If an iPod with video capabilities is con-  
nected to this unit via 3.5 mm plug (4 pole)  
cable (such as the CD-V150M), you can  
enjoy the video contents of the connected  
iPod.  
3
Touch each of the arrows on the four  
corners of the screen.  
To cancel the adjustment, press and hold  
HOME.  
#
4
Press HOME to complete 4-point adjust-  
!
A portable audio/video player can be con-  
nected by using a 3.5 mm plug (4 pole) with  
an RCA cable (sold separately). However,  
depending on the cable, a reverse connec-  
tion between the red (right side audio)  
cable and yellow (video) cable may be re-  
quired in order for the sound and video  
image to be reproduced correctly.  
ment.  
Data for the adjusted position is saved.  
#
being saved.  
Do not turn off the engine while the data is  
5
Press HOME to proceed to 16-point ad-  
justment.  
The 16-point touch panel adjustment screen  
appears.  
#
%
Insert the stereo mini plug into the  
To cancel the adjustment, press and hold  
AUX input jack on this unit.  
Refer to Installation on page 77.  
Refer to Whats what on page 11.  
HOME.  
75  
En  
 
Section  
16  
Other functions  
Using an external unit  
An external unit refers to a Pioneer product,  
such as those which will be available in the fu-  
ture. Although incompatible as a source, the  
basic functions of up to two external units can  
be controlled with this unit. When two external  
units are connected, the external units are  
automatically allocated to external unit 1 or ex-  
ternal unit 2.  
The basic operations of the external unit are  
explained below. The allocated functions will  
differ depending on the connected external  
unit. For details concerning these functions,  
refer to the owners manual for the external  
unit.  
Actions will differ depending on  
the connected external unit.  
F1  
F2  
F3  
F4  
Function 1 to 4  
Actions will differ depending on  
the connected external unit.  
Using the functions allocated to 1  
to 6 keys.  
Actions will differ depending on  
the connected external unit.  
Basic operations  
The functions allocated to the following opera-  
tions will differ depending on the connected  
external unit. For details concerning these  
functions, refer to the owners manual for the  
connected external unit.  
Auto  
Switching to auto or manual.  
Audio  
Switching to video and audio.  
Video  
Changing the screen mode.  
Switching the equalizer curves.  
Touch and hold for more than two  
seconds to turn the auto-equalizer  
on or off.  
76  
En  
 
Section  
Installation  
17  
Connecting the units  
WARNING  
!
LIGHT GREEN LEAD AT POWER CON-  
NECTOR IS DESIGNED TO DETECT  
PARKED STATUS AND MUST BE CON-  
NECTED TO THE POWER SUPPLY SIDE  
OF THE PARKING BRAKE SWITCH. IM-  
PROPER CONNECTION OR USE OF  
THIS LEAD MAY VIOLATE APPLICABLE  
LAW AND MAY RESULT IN SERIOUS IN-  
JURY OR DAMAGE.  
WARNING  
!
To avoid the risk of accident and the potential  
violation of applicable laws, no viewing of  
front seat video should ever occur while the  
vehicle is being driven. Also, rear displays  
should not be in a location where they are visi-  
bly distracting to the driver.  
!
In some countries or states the viewing of  
images on a display inside a vehicle even by  
persons other than the driver may be illegal.  
Where such regulations apply, they must be  
obeyed and this units DVD features should  
not be used.  
WARNING  
!
!
Use speakers over 50 W (output value) and be-  
tween 4 W to 8 W (impedance value). Do not  
use 1 W to 3 W speakers for this unit.  
The black cable is ground. When installing  
this unit or power amp (sold separately), make  
sure to connect the ground wire first. Make  
sure that the ground cable is properly con-  
nected to metal parts of the car body using a  
spade terminal sold commercially. The ground  
wire of the power amp and the one of this unit  
or any other device must be connected to the  
car separately with different screws. If the  
screw for the ground wire loosens or falls out,  
it could result in fire, generation of smoke or  
malfunction.  
CAUTION  
!
PIONEER does not recommend that you in-  
stall or service your display unit yourself. In-  
stalling or servicing the product may expose  
you to risk of electric shock or other hazards.  
Refer all installation and servicing of your dis-  
play unit to authorized Pioneer service person-  
nel.  
!
!
Secure all wiring with cable clamps or electri-  
cal tape. Do not allow any bare wiring to re-  
main exposed.  
Do not drill a hole into the engine compart-  
ment to connect the yellow cable of the dis-  
play unit to the vehicle battery. Engine  
vibration may eventually cause the insulation  
to fail at the point where the wire passes from  
the passenger compartment into the engine  
compartment. Take extra care in securing the  
wire at this point.  
POWER AMP  
Ground wire  
Other devices  
(Another electronic  
device in the car)  
!
It is extremely dangerous to allow the micro-  
phone lead to become wound around the  
steering column or shift lever. Be sure to in-  
stall the unit in such a way that it will not ob-  
struct driving.  
Metal parts of cars body  
!
!
Make sure that cables will not interfere with  
moving parts of the vehicle, such as the shift  
lever, parking brake or seat sliding mechan-  
ism.  
Do not shorten any cables. If you do, the pro-  
tection circuit may fail to work properly.  
77  
En  
 
Section  
17  
Installation  
na, connect it to the antenna booster power  
supply terminal.  
Important  
!
This unit cannot be installed in a vehicle with-  
out ACC (accessory) position on the ignition  
switch.  
!
!
Never connect the blue/white cable to the  
power terminal of an external power amp.  
Also, never connect it to the power terminal of  
the auto antenna. Doing so may result in bat-  
tery drain or a malfunction.  
IP-BUS connectors are color-coded. Be sure  
to connect connectors of the same color.  
ACC position  
No ACC position  
!
!
Use this unit with a 12-volt battery and nega-  
tive grounding only. Failure to do so may result  
in a fire or malfunction.  
To prevent a short-circuit, overheating or mal-  
function, be sure to follow the directions  
below.  
Disconnect the negative terminal of the  
battery before installation.  
Secure the wiring with cable clamps or ad-  
hesive tape. Wrap adhesive tape around  
wiring that comes into contact with metal  
parts to protect the wiring.  
Place all cables away from moving parts,  
such as the shift lever and seat rails.  
Place all cables away from hot places,  
such as near the heater outlet.  
Do not connect the yellow cable to the bat-  
tery by passing it through the hole to the  
engine compartment.  
Cover any disconnected cable connectors  
with insulating tape.  
Do not shorten any cables.  
Never cut the insulation of the power cable  
of this unit in order to share the power  
with other devices. The current capacity of  
the cable is limited.  
Use a fuse of the rating prescribed.  
Never wire the negative speaker cable di-  
rectly to ground.  
Never band together negative cables of  
multiple speakers.  
!
When this unit is on, control signals are sent  
through the blue/white cable. Connect this  
cable to the system remote control of an exter-  
nal power amp or the vehicles auto-antenna  
relay control terminal (max. 300 mA 12 V DC).  
If the vehicle is equipped with a glass anten-  
78  
En  
Section  
Installation  
17  
79  
En  
Section  
17  
Installation  
Connecting the power cord  
26 pin cable (Supplied with navigation unit)  
Insert the 26 pin cable in the direction  
indicated in the figure.  
RGB input  
This product  
Antenna input  
Navigation system  
(AVIC-U220(sold  
separately))  
Fuse (10 A)  
Please contact your  
dealer to inquire about  
the connectable  
AUX jack (3.5 ø) (AVH-P4400BH only)  
Use a mini plug cable to connect with auxiliary device.  
navigation unit.  
Yellow  
Connect to the constant 12 V supply terminal.  
Orange/white  
Connect to lighting switch terminal.  
Red  
Connect to terminal controlled by ignition switch (12 V DC).  
Black (chassis ground)  
Connect to a clean, paint-free metal location.  
White  
Gray  
Front speaker  
Front speaker  
White/black  
Green  
Gray/black  
Violet  
Left  
Right  
Rear speaker or  
Subwoofer (4 Ω)  
Rear speaker or  
Subwoofer (4 Ω)  
Green/black  
Violet/black  
When using a subwoofer of 70 W (2 Ω), be sure to connect with Violet and Violet/black leads of this unit.  
Do not connect anything to Green and Green/black leads.  
Green  
Violet  
Subwoofer (4 Ω)  
× 2  
Not used.  
Green/black  
Violet/black  
80  
En  
Section  
Installation  
17  
4 m (13 ft. 1 in.)  
Microphone (AVH-P4400BH/AVH-P3400BH/AVH-P2400BT only)  
Microphone input (AVH-P4400BH/AVH-P3400BH/AVH-P2400BT only)  
Wired remote input  
Hard-wired remote control adaptor can be connected  
(sold separately).  
Violet/white  
Of the two lead wires connected to the back lamp, connect the one  
in which the voltage changes when the gear shift is in the  
REVERSE (R) position. This connection enables the unit to  
sense whether the car is moving forwards or backwards.  
Yellow/black  
If you use an equipment with Mute function, wire this lead to  
the Audio Mute lead on that equipment. If not, keep the Audio  
Mute lead free of any connections.  
Connection method  
1. Clamp the lead.  
2. Clamp firmly with  
needle-nosed pliers.  
Note:  
· The position of the parking brake switch depends on the vehicle model. For details,  
consult the vehicle Owner’s Manual or dealer.  
Light green  
Used to detect the ON/OFF status of the parking  
brake. This lead must be connected to the power  
supply side of the parking brake switch.  
Parking brake  
switch  
Power supply side  
Ground side  
Blue/white  
Connect to system control terminal of the power amp or  
auto-antenna relay control terminal (max. 300 mA 12 V DC).  
With a 2 speaker system, do not connect anything to the speaker leads  
that are not connected to speakers.  
Note:  
· Change the initial setting of this unit. The  
subwoofer output of this unit is monaural.  
81  
En  
Section  
17  
Installation  
When connecting to separately sold power amp  
Rear output  
Front output  
Power amp  
(sold separately)  
To rear output  
To front output  
Power amp  
(sold separately)  
Power amp  
(sold separately)  
Subwoofer  
output  
To subwoofer  
output  
This product  
Connect with RCA cables  
(sold separately)  
System remote control  
Blue/white  
Connect to system control terminal of the  
power amp or auto-antenna relay control  
terminal. (max. 300 mA 12 V DC).  
Left  
Right  
Subwoofer  
Subwoofer  
Front speaker  
Rear speaker  
Front speaker  
Rear speaker  
Perform these connections when  
using the optional amplifier.  
82  
En  
Section  
Installation  
17  
Connecting the system (for AVH-P1400DVD model)  
Microphone  
for hands-free phoning  
(supplied with Bluetooth adapter)  
Bluetooth adapter  
(e.g. CD-BTB200)  
(sold separately)  
This product  
Black  
IP-BUS input  
IP-BUS cable  
(Supplied with Bluetooth adapter)  
Connecting the system (for AVH-P2400BT/AVH-P1400DVD model)  
This product  
HD Radio tuner  
(sold separately)  
IP-BUS input  
IP-BUS cable  
(Supplied with HD Radio tuner)  
83  
En  
Section  
17  
Installation  
When connecting with optional CD-IU201V cable  
iPod with video capabilities  
(sold separately)  
This product  
USB input  
Dock connector  
1.5 m (4 ft. 11 in.)  
USB cable  
(Supplied with this unit for  
AVH-P4400BH.  
AUX input  
(AUX)  
Sold separately for other models.)  
2 m (6 ft. 7 in.  
)
Interface cable  
(CD-IU201V) (sold separately)  
84  
En  
Section  
Installation  
17  
When connecting the external video component and the display  
External video component (sold  
separately)  
To audio outputs  
To video output  
Audio inputs  
(L IN, R IN)  
RCA cables  
(sold separately)  
Video input (V IN)  
This product  
Rear monitor output  
To video input  
(V OUT)  
Display with RCA input jacks  
(sold separately)  
!
It is necessary to change AV Input in the  
system menu when connecting the exter-  
nal video component.  
When using a display connected to rear video output  
This products rear video output and rear  
audio output are for connection of a display to  
enable passengers in the rear seats to watch  
the DVD, etc.  
WARNING  
Never install the display in a location where it  
is visible to the driver while driving.  
!
85  
En  
Section  
17  
Installation  
Rear view camera input (R.C IN)  
When connecting with a rear  
view camera  
When the shift lever is switched to REVERSE  
(R), the display on this unit automatically  
switches to the rear view image. You need to  
set the Camera Polarity properly in the sys-  
tem menu. For details about the settings, refer  
You can also switch the rear view image by  
pressing the touch key. For details, refer to  
This product  
RCA cable  
(sold separately)  
To video output  
WARNING  
USE INPUT ONLY FOR REVERSE OR MIR-  
ROR IMAGE REAR VIEW CAMERA. OTHER  
USE MAY RESULT IN INJURY OR DAMAGE.  
Rear view camera  
(sold separately)  
Violet/white  
Of the two lead wires  
connected to the back lamp,  
connect the one in which the  
voltage changes when the  
gear shift is in the REVERSE  
(R) position. This connection  
enables the unit to  
CAUTION  
!
You must use a camera which outputs mir-  
ror reversed images.  
!
!
The screen image may appear reversed.  
The rear view camera function is to be used  
as an aid to keep an eye on trailers, or while  
backing up. Do not use for entertainment pur-  
poses.  
sense whether the car is  
moving forwards or  
backwards.  
!
Objects in the rear view may appear closer or  
more distant than they actually are.  
86  
En  
Section  
Installation  
17  
!
When installing, to ensure proper heat disper-  
sal when using this unit, make sure you leave  
ample space behind the rear panel and wrap  
any loose cables so they are not blocking the  
vents.  
Installation  
Notes  
!
!
!
Check all connections and systems before  
final installation.  
Do not use unauthorized parts as this may  
cause malfunctions.  
Consult your dealer if installation requires dril-  
ling of holes or other modifications to the vehi-  
cle.  
Leave ample  
space  
5 cm  
!
!
Do not install this unit where:  
it may interfere with operation of the vehi-  
cle.  
it may cause injury to a passenger as a re-  
sult of a sudden stop.  
Do not install the display where it may (i) ob-  
struct the drivers vision, (ii) impair the perfor-  
mance of any of the vehicles operating  
systems or safety features, including air bags,  
hazard lamp buttons or (iii) impair the drivers  
ability to safely operate the vehicle.  
The semiconductor laser will be damaged if it  
overheats. Install this unit away from hot  
places such as near the heater outlet.  
Optimum performance is obtained when the  
unit is installed at an angle of less than 30°.  
5 cm  
5cm  
!
To some types of vehicles, this unit cannot be  
properly installed. In such case, use the op-  
tional installation kit (ADT-VA133).  
Installation using the screw  
holes on the side of the unit  
!
!
%
Fastening the unit to the factory radio-  
mounting bracket.  
Position the unit so that its screw holes are  
aligned with the screw holes of the bracket,  
and tighten the screws at 3 locations on each  
side.  
87  
En  
 
Section  
17  
Installation  
Installing the microphone (For  
AVH-P4400BH/AVH-P3400BH/  
AVH-P2400BT model)  
1
2
CAUTION  
It is extremely dangerous to allow the micro-  
phone lead to become wound around the steer-  
ing column or shift lever. Be sure to install the  
unit in such a way that it will not obstruct driving.  
Note  
3
Install the microphone in a position and orienta-  
tion that will enable it to pick up the voice of the  
person operating the system.  
4
5
When installing the microphone on  
the sun visor  
1 If the pawl gets in the way, bend it down.  
2 Factory radio mounting bracket  
3 Use either truss (5 mm × 8 mm) or flush  
surface (5 mm × 9 mm) screws, depending  
on the bracket screw holes.  
1
Install the microphone on the micro-  
phone clip.  
4 Frame  
1
2
In some types of vehicles, discrepancy may  
occur between the unit and the dashboard.  
If this happens, use the supplied frame to  
fill the gap.  
5 Dashboard or console  
1 Microphone  
2 Microphone clip  
2
Install the microphone clip on the sun  
visor.  
With the sun visor up, install the microphone  
clip. (Lowering the sun visor reduces the voice  
recognition rate.)  
88  
En  
Section  
Installation  
17  
2
Install the microphone clip on the rear  
1
side of the steering column.  
1
2
1 Microphone clip  
2 Clamp  
Use separately sold clamps to secure the  
lead where necessary inside the vehicle.  
2
When installing the microphone on  
the steering column  
1
Install the microphone on the micro-  
phone clip.  
1 Double-sided tape  
2 Clamp  
1
2
Use separately sold clamps to secure the  
lead where necessary inside the vehicle.  
Adjusting the microphone angle  
3
4
1 Microphone  
2 Microphone base  
3 Microphone clip  
4 Fit the microphone lead into the groove.  
#
Microphone can be installed without using  
microphone clip. In this case, detach the micro-  
phone base from the microphone clip. To detach  
the microphone base from the microphone clip,  
slide the microphone base.  
The microphone angle can be adjusted.  
89  
En  
Appendix  
Additional information  
Troubleshooting  
Common  
Symptom  
The  
Cause  
Action (Refer-  
ence page)  
icon is  
The operation is This operation is  
Symptom  
Cause  
Action (Refer-  
ence page)  
displayed, and prohibited for the not possible.  
operation is not disc.  
possible.  
The power will Leads and con-  
Confirm once more  
The operation is This operation is  
not turn on.  
The unit will  
not operate.  
nectors are incor- that all connec-  
rectly connected. tions are correct.  
not compatible  
with the config-  
uration of the  
disc.  
not possible.  
The fuse is  
blown.  
Rectify the cause  
and then replace  
the fuse. Be sure to  
install a fuse with  
the same rating.  
The image dis- The data could  
Stop playback  
once, and start  
played stops  
(pauses) and  
no longer be  
read during play- playback again.  
the unit cannot back.  
be operated.  
Operation with Battery power is Load a new battery.  
the remote  
control is not  
possible.  
low.  
There is no  
sound.  
The volume level Adjust the volume  
is low. level.  
Some operations Try operating with  
are prohibited  
with certain  
discs.  
another disc.  
The unit does  
not operate  
correctly even  
when the ap-  
propriate re-  
mote control  
buttons are  
pressed.  
The volume  
level is low.  
The attenuator is Turn the attenuator  
on.  
off.  
The sound and The unit is not  
Firmly secure the  
unit.  
video skip.  
firmly secured.  
File size and  
transmission rate that is within the  
are above recom- recommended size  
Create a DivX file  
mended rates.  
and transmission  
rate.  
Playback is not The disc is dirty. Clean the disc.  
possible.  
The type of disc Check the disc  
The aspect  
ratio is incor-  
rect and the  
image is  
The aspect ratio Select the appro-  
setting is incor- priate setting for  
loaded cannot be type.  
played on this  
unit.  
rect for the dis-  
play.  
your display. (Page  
The disc loaded Change the disc to  
is not compatible one that is compa-  
stretched.  
The motor  
sounds when  
the ignition  
switch is  
turned ON (or  
is turned to  
ACC).  
The unit is con-  
This is a normal  
with this video  
system.  
tible with your  
video system.  
firming whether operation.  
or not a disc is  
loaded.  
There is no  
sound.  
The volume  
level will not  
rise.  
Cables are not  
connected cor-  
rectly.  
Connect the cables  
correctly.  
The unit is per-  
forming still,  
slow motion or  
frame-by-frame  
playback.  
There is no sound  
during still, slow  
motion or frame-  
by-frame playback.  
Nothing is dis- The rear view  
played.  
The touch  
panel keys can-  
not be used.  
Connect a rear  
view camera.  
camera is not  
connected.  
Camera Polarity Press and hold  
There is no  
image dis-  
played.  
The parking  
brake cable is  
not connected.  
Connect the park-  
ing brake cable,  
and apply the park-  
ing brake.  
is at incorrect  
setting.  
HOME to return to  
the source display  
and then select the  
correct setting for  
Camera Polarity.  
The parking  
brake is not ap-  
plied.  
Connect the park-  
ing brake cable,  
and apply the park-  
ing brake.  
90  
En  
 
Appendix  
Additional information  
Symptom  
Cause  
Action (Refer-  
ence page)  
Symptom  
Cause  
Action (Refer-  
ence page)  
No xxxx ap-  
There is no em-  
Switch the display  
No subtitles  
The DVD being  
Subtitles are not  
pears when a  
display is chan- mation.  
ged (No Title,  
bedded text infor- or play another  
are displayed. played does not displayed if they  
feature subtitles. are not recorded  
on the disc.  
track/file.  
for example).  
You can only  
Switch the lan-  
Subfolders can- Folder repeat  
Select the repeat  
Select the repeat  
switch between guage using the  
items indicated disc menu.  
in the disc menu.  
not be played  
back.  
play has been se- range again.  
lected.  
The repeat  
Another folder  
Playback is not The DVD being  
The language can-  
performed with played does not not be switched if  
the audio lan- feature dialog or the selected lan-  
range changes was selected dur- range again.  
automatically. ing repeat play.  
guage and sub- subtitles in the  
title language selected lan-  
guage is not re-  
corded on the disc.  
Track search or  
fast forward/re-  
verse was per-  
formed during  
file repeat play.  
Select the repeat  
range again.  
settings se-  
guage.  
lected in Video  
Setup menu.  
The viewing  
angle cannot  
be switched.  
The DVD being  
played does not cannot be  
feature scenes  
The viewing angle  
DVD  
switched if the  
shot from multi- DVD does not fea-  
Symptom  
Cause  
Action (Refer-  
ence page)  
ple angles.  
ture scenes re-  
corded from  
Playback is not The loaded disc Replace the disc  
possible. has a different re- with one featuring  
multiple angles.  
You are trying to Switch between  
switch to multi- multiple angles  
angle viewing for when watching  
a scene that was scenes recorded  
gion number  
from this unit.  
the same region  
number as this  
unit.  
A parental lock Parental lock is  
message is dis- activated.  
played and  
Turn parental lock  
off or change the  
not recorded  
from multiple an-  
from multiple an- gles.  
gles.  
playback is not  
possible.  
The image is  
extremely un-  
Some discs fea- Since this unit is  
ture a signal to  
compatible with  
Parental lock  
The code number Enter the correct  
cannot be can- is incorrect.  
celed.  
clear/distorted prohibit copying. the analog copy  
code number.  
and dark dur-  
ing playback.  
generation man-  
agement system,  
when playing a  
disc that has a sig-  
nal prohibiting  
You have forgot- Touch C 10 times  
ten your code  
number.  
to cancel the code  
number.  
copying, horizontal  
stripes or other im-  
perfections may  
appear when  
viewed on some  
displays. This is  
not a malfunction.  
Dialog lan-  
guage (and  
subtitle lan-  
The DVD being  
played does not not be switched if  
feature multiple they are not re-  
The language can-  
guage) cannot language record- corded on the disc.  
be switched.  
ings.  
You can only  
Switch the lan-  
switch between guage using the  
items indicated disc menu.  
in the disc menu.  
91  
En  
Appendix  
Additional information  
Video CD  
Symptom  
Bluetooth audio/telephone  
Cause  
Action  
Symptom  
Cause  
Action  
The PBC (play- The Video CD  
This operation is  
not available for  
The sound  
from the  
Bluetooth  
There is a call in The sound will be  
back control)  
menu cannot  
be called up.  
being played  
does not feature Video CDs that do  
PBC.  
progress on a  
Bluetooth con-  
played back when  
the call is termi-  
nated.  
not feature PBC.  
audio source is nected cellular  
not played  
back.  
phone.  
Repeat play  
The Video CD  
This operation is  
and track/time being played fea- not available for  
A Bluetooth-con- Do not operate the  
search are not tures PBC.  
possible.  
Video CDs that fea-  
ture PBC.  
nected cellular  
phone is cur-  
rently being oper-  
ated.  
cellular phone at  
this time.  
iPod  
A call was made Reconnect the  
with a Bluetooth- Bluetooth connec-  
connected cellu- tion between this  
Symptom  
Cause  
Action  
The iPod does The cables are in- Disconnect the  
lar phone and  
unit and the cellu-  
not operate  
correctly.  
correctly con-  
nected.  
cable from the  
iPod. Once the  
iPods main menu  
is displayed, recon-  
nect the iPod and  
reset it.  
then immediately lar phone.  
terminated. As a  
result, communi-  
cation between  
this unit and the  
cellular phone  
The iPod version Update the iPod  
is old. version.  
was not termi-  
nated properly.  
Sound from the The audio output Use the iPod to  
iPod cannot be direction may change the audio  
heard.  
switch automati- output direction.  
cally when the  
Bluetooth and  
USB connections  
are used at the  
Error messages  
When you contact your dealer or your nearest  
Pioneer Service Center, be sure to note the  
error message.  
same time.  
Tuner  
Message  
Cause  
Action  
No Data Pro- This unit cannot Move to the desir-  
vided  
receive artist  
able location with  
name/song title good reception.  
information.  
No Data  
This unit cannot Move to the desir-  
receive program able location with  
service name in- good reception.  
formation.  
DVD  
Message  
Cause  
Action  
Different Re- The disc does not Replace the DVD  
gion Disc  
have the same  
region number  
as this unit.  
with one bearing  
the correct region  
number.  
92  
En  
 
Appendix  
Additional information  
Message  
Cause  
Action  
Message  
Cause  
Action  
Unplayable  
File  
This type of file  
cannot be played can be played.  
on this unit.  
Select a file that  
Error-02-XX/  
FF-FF  
The disc is dirty. Clean the disc.  
The disc is  
scratched.  
Replace the disc.  
Format Read Sometimes there Wait until the mes-  
is a delay be- sage disappears  
tween the start of and you hear  
The disc is  
loaded upside  
down.  
Check that the disc  
is loaded correctly.  
playback and  
sound.  
There is an elec- Turn your vehicles  
trical or mechan- ACC switch off and  
ical error.  
when you start to  
hear any sound.  
on.  
Video frame  
rate not sup- rate is more than can be played.  
ported 30 fps.  
DivX files frame Select a file that  
Unplayable  
Disc  
This type of disc Replace the disc  
cannot be played with one that can  
on this unit.  
be played on this  
unit.  
Audio Format This type of file is Select a file that  
not supported not supported on can be played.  
this unit.  
The inserted disc Replace the disc.  
does not contain  
any playable  
files.  
External storage device (USB)  
Message  
Cause  
Action  
Protect  
Skipped  
TEMP  
All the files on  
the inserted disc  
are embedded  
with DRM.  
Replace the disc.  
Unplayable  
File  
This type of file  
cannot be played can be played.  
on this unit.  
Select a file that  
The inserted disc Play an audio file  
contains DRM  
protected files.  
There are no  
songs.  
Transfer the audio  
files to the USB  
portable audio  
player/USB mem-  
ory and connect.  
not embedded with  
Windows Media  
DRM 9/10.  
The temperature Wait until the unit  
of the unit is out- returns to a tem-  
side the normal perature within the  
operating range. normal operating  
limits.  
Security for the  
connected USB memory instruc-  
memory is en-  
abled.  
Follow the USB  
tions to disable se-  
curity.  
Rental ex-  
pired.  
The inserted disc Select a file that  
contains expired can be played.  
DivX VOD con-  
Format Read Sometimes there Wait until the mes-  
is a delay be- sage disappears  
tween the start of and you hear  
tent.  
playback and  
sound.  
when you start to  
hear any sound.  
Video resolu- The inserted disc Select a file that  
tion not sup- contains a high can be played.  
ported  
definition DivX/  
MPEG-1/  
MPEG-2/MPEG-4  
file.  
Skipped  
The connected  
USB portable  
audio player/  
USB memory  
contains WMA  
files that are pro-  
tected by  
Play an audio file  
not embedded with  
Windows Media  
DRM 9/10.  
It is not possi- This units flash Select a file that  
ble to write it memory used as can be played.  
in the flash.  
the temporary  
storage area is  
full.  
Windows Med-  
iaä DRM 9/10.  
Your device is This units DivX Register this unit  
not author-  
ized to play  
registration code to the DivX VOD  
has not been contents provider.  
this DivX pro- authorized by the  
tected video. DivX VOD con-  
tents provider.  
93  
En  
Appendix  
Additional information  
Message  
Cause  
Action  
Message  
Protect  
Cause  
Action  
All the files on  
the connected  
USB portable  
audio player/  
Transfer audio files  
not protected by  
Windows Media  
DRM 9/10 to the  
Rental ex-  
pired.  
The inserted ex- Select a file that  
ternal storage de- can be played.  
vice contains  
expired DivX  
VOD content.  
USB memory are USB portable  
protected by audio player/USB  
Windows Media memory and con-  
DRM 9/10. nect.  
Video resolu- The inserted ex- Select a file that  
tion not sup- ternal storage de- can be played.  
ported  
vice contains a  
high definition  
DivX/MPEG-1/  
MPEG-2/MPEG-4  
file.  
Incompatible The USB device Connect a USB  
USB  
connected to is  
portable audio  
not supported by player or USB  
this unit.  
memory that is  
USB Mass Storage  
Class compliant.  
It is not possi- This units flash Select a file that  
ble to write it memory used as can be played.  
in the flash.  
the temporary  
storage area is  
full.  
The USB device The connected  
is not formatted USB device should  
with FAT16 or  
FAT32.  
be formatted with  
FAT16 or FAT32.  
Your device is This units DivX Register this unit  
Check USB  
The USB connec- Check that the  
tor or USB cable USB connector or  
not author-  
ized to play  
this DivX pro-  
tected video.  
registration code to the DivX VOD  
has not been  
contents provider.  
has short-  
circuited.  
USB cable is not  
caught in some-  
thing or damaged.  
authorized by the  
DivX VOD con-  
tents provider.  
Wait until the mes-  
sage disappears  
and you hear  
sound.  
The connected  
USB portable  
audio player/  
USB memory  
Disconnect the  
USB portable  
audio player/USB  
memory and do  
Format Read Sometimes there  
is a delay be-  
tween the start of  
playback and  
consumes more not use it. Turn the  
when you start to  
hear any sound.  
than maximum  
allowable cur-  
rent.  
ignition switch to  
OFF, then to ACC  
or ON and then  
connect a compli-  
ant USB portable  
audio player/USB  
memory.  
Video frame  
rate not sup- rate is more than can be played.  
ported 30 fps.  
DivX files frame Select a file that  
Audio Format This type of file is Select a file that  
not supported not supported on can be played.  
this unit.  
Error-02-9X/- Communication Perform one of the  
DX  
failed.  
following opera-  
tions.  
iPod  
Turn the ignition  
switch OFF and  
back ON.  
Disconnect the  
USB portable  
audio player/USB  
memory.  
Change to a dif-  
ferent source.  
Then, return to the  
USB portable  
audio player/USB  
memory.  
Message  
Format Read Sometimes there Wait until the mes-  
is a delay be- sage disappears  
tween the start of and you hear  
Cause  
Action  
playback and  
sound.  
when you start to  
hear any sound.  
94  
En  
Appendix  
Additional information  
Bluetooth  
Message  
Cause  
Action  
Message  
Cause  
Action  
Error-02-6X/- Communication Disconnect the  
9X/-DX  
failed.  
cable from the  
iPod. Once the  
iPods main menu  
is displayed, recon-  
nect the iPod and  
reset it.  
Error-10  
The power failed Turn the ignition  
for the Bluetooth switch OFF and  
module of this  
unit.  
then to ACC or ON.  
If the error mes-  
sage is still dis-  
played after  
performing the  
above action,  
please contact  
your dealer or an  
authorized Pioneer  
Service Station.  
iPod failure.  
Disconnect the  
cable from the  
iPod. Once the  
iPods main menu  
is displayed, recon-  
nect the iPod and  
reset it.  
Pandora  
Error-02-67  
Stop  
The iPod firm-  
ware version is  
old.  
Update the iPod  
version.  
Message  
Cause  
Action  
Error-19  
Communication Disconnect the  
There are no  
songs.  
Transfer songs to  
the iPod.  
failed.  
cable from the  
iPod. Once the  
iPods main menu  
is displayed, recon-  
nect the iPod and  
reset it.  
There are no  
Select a list that  
songs in the cur- contains songs.  
rent list.  
Not Found  
No related  
songs.  
Transfer songs to  
the iPod.  
Start up the  
Pandora Ap-  
The Pandora ap- Start up the  
plication has not Pandora applica-  
plication from started running tion from your  
iTunes tagging  
Message Cause  
your Device.  
yet.  
iPod/iPhone.  
Action  
Unable to  
save thumb  
rating. Try  
again later.  
Unable to save  
thumb rating.  
Try again later.  
iPod full. Tags Memory used for Sync the iPod with  
not trans-  
ferred.  
tag information iTunes and clean  
on the iPod is  
full.  
up the tagged play-  
list.  
Unable to  
save Book-  
mark. Try  
Unable to save  
Bookmark.  
Try again later.  
Memory full. This units flash Connect the iPod  
Tags not  
memory used as to this unit and  
again later.  
stored. Con-  
nect iPod.  
the temporary  
storage area is  
full.  
transfer this units  
tag information to  
the iPod.  
Pandora sys- Pandora system Try again later.  
tem mainte-  
nance. Try  
is undergoing  
maintenance.  
Tag transfer  
failed.  
This units tag in- Check the iPod  
formation cannot and try again.  
transfer to the  
again later.  
Skip limit  
reached.  
Skip limit  
reached.  
Do not exceed the  
skip limit.  
iPod.  
Tag store  
failed.  
Tag information Try again.  
cannot be stored  
in this unit.  
This version  
of the  
Pandora Ap-  
plication is  
not sup-  
This version of  
the Pandora ap- iPhone that has a  
plication is not  
supported.  
Connect an iPod/  
compatible version  
of the Pandora ap-  
plication installed.  
Error-8D  
Built-in FLASH  
ROM encoun-  
tered an error  
Turn the ignition  
OFF and ON.  
ported.  
Check Device Device error mes- Please check your  
sage displayed in iPod/iPhone.  
Pandora Applica-  
tion.  
95  
En  
Appendix  
Additional information  
Message  
Pandora is un- Unable to play  
able to play music from  
Cause  
Action  
Message  
Cause  
Action  
Please check your  
iPod/iPhone.  
Error. Please  
check battery. being supplied  
Power is not  
! Connect the bat-  
tery correctly.  
music. Please Pandora.  
see your De-  
vice.  
from the battery ! Check the battery  
to this unit. voltage.  
Create station No station found. Create a station in  
within the  
Pandora Ap-  
plication on  
Device.  
the Pandora appli-  
cation on your  
iPod/iPhone.  
Understanding messages  
No Active Sta- No station se-  
Select a station.  
Messages  
Translation  
tion  
lected.  
Pioneer recommends  
the use of a camera  
which outputs mirror-  
reversed images.  
Otherwise, the screen  
image will appear re-  
versed.  
Screen image may ap-  
pear reversed.  
Understanding auto EQ  
error messages  
When correct measurement of the cars inter-  
ior acoustic characteristics is not possible  
using auto EQ, an error message may appear  
on the display. In such cases, refer to the table  
below to see what the problem is and how it  
may be corrected. After checking, try again.  
Message  
Cause  
Action  
Error. Please  
check MIC.  
The microphone Plug the optional  
is not connected. microphone se-  
curely into the  
jack.  
Error. Please  
check xxxx  
speaker.  
The microphone ! Confirm that the  
cannot pick up  
the measuring  
speakers are con-  
nected correctly.  
tone of a speaker. ! Correct the input  
level setting of the  
power amp con-  
nected to the  
speakers.  
! Plug the micro-  
phone securely  
into the jack.  
Error. Please  
check noise.  
The surrounding ! Stop your car in  
noise level is too a place that is  
high.  
quiet, and switch  
off the engine, air  
conditioner and  
heater.  
! Set the micro-  
phone correctly.  
96  
En  
 
Appendix  
Additional information  
Indicator list  
!
!
Indicates that a cellular phone  
is connected.  
Indicates that an incoming call  
has been received and has not  
been checked yet.  
Area 1  
Area 2  
!
Not displayed for calls made  
when your cellular phone is  
disconnected from this unit.  
Indicates the battery strength of  
the cellular phone.  
!
The level shown on the indica-  
tor may differ from the actual  
battery strength.  
!
If the battery strength is not  
available, nothing is displayed  
in the battery strength indica-  
tor area.  
Area 3  
Area 1  
Indicates the signal strength of the  
cellular phone.  
Indicates that a Bluetooth tele-  
phone is connected.  
Indicates that the digital format is  
Dolby Digital.  
Indicates that Auto EQ is on.  
Shows when radio signal is re-  
ceived.  
Indicates that the digital format is  
MPEG Audio.  
Shows when analog audio of HD  
Radio signal is received.  
Indicates that the digital format is  
Linear PCM.  
Shows when digital audio of HD  
Radio signal is received.  
Indicates the sampling frequency.  
Shows when HD Radio station in-  
formation is received.  
Indicates that the digital format is  
DTS.  
Shows when downloadable song  
information (tag) from a radio sta-  
tion is received.  
Shows when song information  
(tag) from an HD Radio station is  
being saved to this unit.  
1+1ch  
Indicates the audio channel.  
2ch  
Mch  
Shows while searching a song/  
video in alphabet search mode.  
Shows when song information  
(tag) is being saved to your iPod.  
Indicates that a disc with PBC On  
is being played.  
Shows when this unit has the song  
information (tag).  
Shows which audio language has  
been selected.  
97  
En  
 
Appendix  
Additional information  
Shows which subtitle language  
has been selected.  
Shows the category name.  
Shows the folder name of the folder  
containing the MP3/WMA/AAC file  
currently being played.  
Shows which viewing angle has  
been selected.  
Shows the file name of the MP3/  
WMA/AAC file currently being  
played.  
Shows which audio output has  
been selected.  
Shows the preset number of the sta-  
tion currently being tuned in to.  
Area 2  
Shows the disc title of the CD text  
disc currently being played.  
Shows the channel currently being  
tuned in to.  
CH  
Shows the song title when receiving  
the tag information.  
Shows SIRIUS information.  
Shows the track title of the track cur-  
rently being played for CD text discs.  
Shows the song title of the song cur-  
rently being played for MP3/WMA/  
AAC files.  
Area 3  
Shows the title number currently  
being played.  
Shows the comment currently being  
played.  
Shows the chapter number cur-  
rently being played.  
Shows the station name currently  
tuned in to.  
Shows the artist name when receiv-  
ing the tag information.  
Shows the artist name of the track/  
song currently being played for CD  
text discs.  
Shows the artist name of the artist  
currently being played for MP3/  
WMA/AAC files.  
Shows the replay time currently  
being played.  
Shows when the game alert func-  
tion is on while receiving SIRIUS  
stations.  
Shows the genre of the track/song  
currently being played.  
Shows cellular phone information.  
Shows general phone information.  
Shows home phone information.  
Shows office phone information.  
Shows other phone information.  
Indicates that the feature demo is  
on.  
98  
En  
Appendix  
Additional information  
Handling guidelines  
Discs and player  
Certain functions may not be available for some DVD  
video discs.  
It may not be possible to play back some DVD video  
discs.  
Use only discs featuring any of following logos.  
It is not possible to play back DVD-RAM discs.  
This unit is not compatible with discs recorded in  
AVCHD (Advanced Video Codec High Definition) for-  
mat. Do not insert AVCHD discs as you may not be  
able to eject the disc.  
When using discs that can be printed on label sur-  
faces, check the instructions and the warnings of the  
discs. Depending on the discs, inserting and ejecting  
may not be possible. Using such discs may result in  
damage to this equipment.  
Do not attach commercially available labels or other  
materials to the discs.  
!
!
The discs may warp making the disc unplayable.  
The labels may come off during playback and pre-  
vent ejection of the discs, which may result in da-  
mage to the equipment.  
Use 12-cm discs. Do not use 8-cm discs or an adapter  
for 8-cm discs.  
Use only conventional, fully circular discs. Do not use  
shaped discs.  
External storage device (USB)  
Depending on the external storage device (USB), the  
following problems may occur.  
!
!
!
Operations may vary.  
The storage device may not be recognized.  
Files may not be played back properly.  
Do not insert anything other than a DVD-R/RW or CD-  
R/RW into the disc loading slot.  
Do not use cracked, chipped, warped, or otherwise  
damaged discs as they may damage the player.  
USB storage device  
Unfinalized CD-R/RW discs cannot be played back.  
Do not touch the recorded surface of the discs.  
Store discs in their cases when not in use.  
Connections via USB hub are not supported.  
Do not connect anything other than a USB storage  
device.  
Do not attach labels, write on or apply chemicals to  
the surface of the discs.  
Firmly secure the USB storage device when driving.  
Do not let the USB storage device fall onto the floor,  
where it may become jammed under the brake or ac-  
celerator pedal.  
To clean a disc, wipe the disc with a soft cloth out-  
ward from the center.  
Depending on the USB storage device, the device  
may cause noise to occur in the radio.  
Condensation may temporarily impair the players  
performance. Let it rest for about one hour to adjust  
to a warmer temperature. Also, wipe any damp discs  
off with a soft cloth.  
Copyright protected files that are stored in the USB  
devices cannot be played back.  
Playback of discs may not be possible because of  
disc characteristics, disc format, recorded applica-  
tion, playback environment, storage conditions, and  
so on.  
You cannot connect a USB portable audio player/USB  
memory to this unit via USB hub.  
Partitioned USB memory is not compatible with this  
unit.  
Road shocks may interrupt disc playback.  
Read the precautions for discs before using them.  
99  
En  
 
Appendix  
Additional information  
Depending on the application settings and the envir-  
onment, playback of discs recorded on a personal  
computer may not be possible. (For details, contact  
the manufacturer of the application.)  
Depending on the kind of USB portable audio player/  
USB memory you use, the device may not be recog-  
nized or audio files may not be played back properly.  
Do not leave the USB portable audio player/USB  
memory in direct sunlight for extended amounts of  
time. Doing so may cause the device to malfunction  
from the extreme rise in temperature.  
Playback of CD-R/RW discs may become impossible  
in case of direct exposure to sunlight, high tempera-  
tures, or the storage conditions in the vehicle.  
Titles and other text information recorded on a CD-R/  
RW disc may not be displayed by this unit (in the  
case of audio data (CD-DA)).  
iPod  
DualDiscs  
To ensure proper operation, connect the dock connec-  
tor cable from the iPod directly to this unit.  
DualDiscs are two-sided discs that have a recordable  
CD for audio on one side and a recordable DVD for  
video on the other.  
Firmly secure the iPod when driving. Do not let the  
iPod fall onto the floor, where it may become jammed  
under the brake or accelerator pedal.  
Playback of the DVD side is possible with this unit.  
However, since the CD side of DualDiscs is not physi-  
cally compatible with the general CD standard, it may  
not be possible to play the CD side with this unit.  
Frequent loading and ejecting of a DualDisc may re-  
sult in scratches on the disc. Serious scratches can  
lead to playback problems on this unit. In some  
cases, a DualDisc may become stuck in the disc load-  
ing slot and will not eject. To prevent this, we recom-  
mend you refrain from using DualDisc with this unit.  
Please refer to the information from the disc manu-  
facturer for more detailed information about  
DualDiscs.  
About iPod settings  
!
When an iPod is connected, this unit changes the  
EQ (equalizer) setting of the iPod to off in order to  
optimize the acoustics. When you disconnect the  
iPod, the EQ returns to the original setting.  
!
You cannot set Repeat to off on the iPod when  
using this unit. Repeat is automatically changed  
to All when the iPod is connected to this unit.  
Incompatible text saved on the iPod will not be dis-  
played by the unit.  
DVD-R/RW discs  
JPEG picture files  
Unfinalized DVD-R/RW discs which have been re-  
corded in the Video format (video mode) cannot be  
played back.  
Playback of DVD-R/RW discs may not be possible,  
due to disc characteristics, scratches or dirt on the  
disc, or dirt, condensation, etc. on the lens of this  
unit.  
Depending on the application settings and the envir-  
onment, playback of discs recorded on a personal  
computer may not be possible. (For details, contact  
the manufacturer of the application.)  
JPEG is short for Joint Photographic Experts Group  
and refers to a still image compression technology  
standard.  
Files are compatible with Baseline JPEG and EXIF 2.1  
still images up to a resolution of 8 192 × 7 680. (EXIF  
format is used most commonly with digital still cam-  
eras.)  
Playback of EXIF format files that were processed by a  
personal computer may not be possible.  
There is no progressive JPEG compatibility.  
CD-R/RW discs  
DivX video files  
When CD-R/RW discs are used, playback is possible  
only for discs which have been finalized.  
Playback of CD-R/RW discs recorded on a music CD  
recorder or a personal computer may not be possible  
due to disc characteristics, scratches or dirt on the  
disc, or dirt, condensation, etc., on the lens of this  
unit.  
Depending on the composition of the file information,  
such as the number of audio streams or file size,  
there may be a slight delay when playing back discs.  
Some special operations may be prohibited due to  
the composition of the DivX files.  
100  
En  
 
Appendix  
Additional information  
Only DivX files downloaded from a DivX partner site  
are guarantee for proper operation. Unauthorized  
DivX files may not operate properly.  
Sampling frequency: 8 kHz to 48 kHz (32 kHz, 44.1 kHz,  
48 kHz for emphasis)  
Compatible ID3 tag version: 1.0, 1.1, 2.2, 2.3 (ID3 tag  
Version 2.x is given priority over Version 1.x.)  
DRM rental files cannot be operated until playback is  
started.  
M3u playlist: Not compatible  
Recommended file size: 2 GB or less with a transmis-  
sion rate of 2 Mbps or less.  
MP3i (MP3 interactive), mp3 PRO: Not compatible  
The ID code of this unit must be registered to a DivX  
VOD provider in order to playback DivX VOD files. For  
information on ID codes, refer to Displaying the DivXâ  
AAC  
Compatible format: AAC encoded by iTunes  
File extension: .m4a  
For more details about DivX, visit the following site:  
http://www.divx.com/  
Sampling frequency: 8 kHz to 44.1 kHz  
Bit rate: 8 kbps to 320 kbps  
MPEG-1/MPEG-2/MPEG-4 video files  
Apple Lossless: Not compatible  
Elapsed playback time may not be displayed correctly.  
AAC file bought from the iTunes Store (.m4p file ex-  
tension): Not compatible  
Important  
!
!
When naming a JPEG image file, add the cor-  
responding file name extension (.jpg, .jpeg,  
.jpe or .jfif).  
This unit plays back files with these file name  
extensions (.jpg, .jpeg, .jpe or .jfif) as a JPEG  
image file. To prevent malfunctions, do not  
use these extensions for files other than JPEG  
image files.  
DivX compatibility  
Compatible format: DivX video format implemented in  
relation to DivX standards  
File extensions: .avi or .divx  
DivX Ultra format: Not compatible  
DivX HD format: Not compatible  
DivX files without video data: Not compatible  
DivX plus: Not compatible  
Compressed file  
compatibility (disc, USB)  
WMA  
Compatible audio codec: MP2, MP3, Dolby Digital  
LPCM: Not compatible  
Bit rate: 8 kbps to 320 kbps (CBR), VBR  
Sampling frequency: 8 kHz to 48 kHz  
Compatible external subtitle file extension: .srt  
File extension: .wma  
Bit rate: 5 kbps to 320 kbps (CBR), VBR  
Sampling frequency: 8 kHz to 48 kHz  
MPEG-1/MPEG-2/MPEG-4 video  
Windows Media Audio Professional, Lossless, Voice/  
DRM Stream/Stream with video: Not compatible  
File extensions: .wpg or .mpeg (MPEG-1/MPEG-2), .avi  
(MPEG-4)  
MP3  
Compatible audio codec: MP2 (MPEG-1/MPEG-2),  
MP2, MP3, Dolby Digital (MPEG-4)  
File extension: .mp3  
H.264 (MPEG-4AVC): Not compatible  
LPCM: Not compatible  
Bit rate: 8 kbps to 320 kbps (CBR), VBR  
101  
En  
 
Appendix  
Additional information  
!
!
Pioneer cannot guarantee compatibility with  
all USB mass storage devices and assumes  
no responsibility for any loss of data on media  
players, smart phones, or other devices while  
using this product.  
Do not leave the discs/external storage device  
(USB) or iPod in places with high  
temperatures.  
Bit rate: 8 kbps to 320 kbps (CBR), VBR  
Sampling frequency: 8 kHz to 48 kHz  
Supplemental information  
Some characters in a file name (including the file ex-  
tension) or a folder name may not be displayed.  
This unit may not operate correctly depending on the  
application used to encode WMA files.  
There may be a slight delay at the start of playback of  
audio files embedded with image data or audio files  
stored on a USB storage device that has numerous  
folder hierarchies.  
iPod compatibility  
This unit supports only the following iPod models.  
Supported iPod software versions are shown below.  
Older versions may not be supported.  
Made for  
Disc  
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
iPod touch 4th generation (software version 4.3.1)  
iPod touch 3rd generation (software version 4.1)  
iPod touch 2nd generation (software version 4.2.1)  
iPod touch 1st generation (software version 3.1.3)  
iPod classic 160GB (software version 2.0.4)  
iPod classic 120GB (software version 2.0.1)  
iPod classic (software version 1.1.2)  
Playable folders: up to 700  
Playable files: up to 999 for CD-R/RW  
Playable files: up to 3 500 for DVD-R/RW  
File system: ISO 9660 Level 1 and 2, Romeo, Joliet,  
UDF 1.02 (DVD-R/RW)  
iPod with video (software version 1.3)  
iPod nano 6th generation (software version 1.0)  
iPod nano 5th generation (software version 1.0.1)  
iPod nano 4th generation (software version 1.0.4)  
iPod nano 3rd generation (software version 1.1.3)  
iPod nano 2nd generation (software version 1.1.3)  
iPod nano 1st generation (software version 1.3.1)  
iPhone 4 (software version 4.3.3)  
iPhone 3GS (software version 4.1)  
iPhone 3G (software version 4.2.1)  
iPhone (software version 3.1.3)  
Multi-session playback: Compatible  
Packet write data transfer: Not compatible  
Regardless of the length of blank sections between  
the songs from the original recording, compressed  
audio discs play with a short pause between songs.  
External storage device (USB)  
Playable folders: up to 6 000 (up to 700 for DivX/  
MPEG-1/MPEG-2/MPEG-4)  
Depending on the generation or version of the iPod,  
some functions may not be available.  
Playable files: up to 65 535, up to 1 000 for one folder  
Playback of copyright-protected files: Not compatible  
Operations may vary depending on the software ver-  
sion of iPod.  
Partitioned external storage device (USB): Only the  
first playable partition can be played.  
When using an iPod, an iPod Dock Connector to USB  
Cable is required.  
There is no compatibility for Multi Media Cards  
(MMC).  
When you use Pioneer CD-IU51V/CD-IU201V interface  
cable, consult your dealer for details.  
About the file/format compatibility, refer to the iPod  
manuals.  
CAUTION  
Audiobook, Podcast: Compatible  
!
Pioneer accepts no responsibility for data lost  
on the USB memory/USB portable audio  
player even if that data is lost while using this  
unit.  
102  
En  
 
Appendix  
Additional information  
Using the display correctly  
CAUTION  
Pioneer accepts no responsibility for data lost on  
the iPod, even if that data is lost while this unit is  
used.  
CAUTION  
!
If liquid or foreign matter should get inside  
this unit, turn off the power immediately and  
consult your dealer or the nearest authorized  
PIONEER Service Station. Do not use the unit  
in this condition because doing so may result  
in fire, electric shock, or other failure.  
If you notice smoke, a strange noise or smell,  
or any other abnormal signs from the display,  
turn off the power immediately and consult  
your dealer or the nearest authorized  
PIONEER Service Station. Using this unit in  
this condition may result in permanent da-  
mage to the system.  
Do not disassemble or modify this unit, as  
there are high-voltage components inside  
which may cause electric shock. Be sure to  
consult your dealer or the nearest authorized  
PIONEER Service Station for internal inspec-  
tion, adjustments, or repairs.  
Sequence of audio files  
The user cannot assign folder numbers and  
specify playback sequences with this unit.  
!
Example of a hierarchy  
01  
02  
03  
!
: Folder  
: Compressed  
audio file  
04  
01 to 05: Folder  
number  
05  
1 to 6: Playback  
sequence  
Level 1 Level 2 Level 3 Level 4  
Disc  
Handling the display  
Folder selection sequence or other operation  
may differ depending on the encoding or writ-  
ing software.  
!
Never touch the screen with anything be-  
sides your finger when operating the touch  
panel function. The screen can scratch ea-  
sily.  
External storage device (USB)  
The playback sequence is the same as the re-  
corded sequence in the external storage de-  
vice (USB).  
To specify the playback sequence, the follow-  
ing method is recommended.  
1 Create a file name that includes numbers that  
specify the playback sequence (e.g.,  
001xxx.mp3 and 099yyy.mp3).  
2 Put those files into a folder.  
3 Save the folder that contains the files to the  
external storage device (USB).  
However, depending on the system environ-  
ment, you may not be able to specify the play-  
back sequence.  
For USB portable audio players, the sequence  
is different and depends on the player.  
!
When the display is subjected to direct sun-  
light for a long period of time, it will be-  
come very hot resulting in possible  
damage to the LCD screen. You should  
avoid exposing the display unit to direct  
sunlight as much as possible.  
!
The display should be used within the tem-  
perature range of 10 °C to +60 °C (14 °F to  
140 °F).  
At temperatures higher or lower than this  
operating temperature range, the display  
may not operate normally.  
!
!
The LCD screen is exposed in order to in-  
crease its visibility within the vehicle. Do  
not press it strongly on it as this may da-  
mage it.  
Do not push the LCD screen forcefully as  
this may scratch it.  
103  
En  
 
Appendix  
Additional information  
Liquid crystal display (LCD) screen  
Bluetooth profiles  
!
!
!
Heat from the heater may damage the LCD  
screen, and cool air from the cooler may  
cause moisture to form inside the display  
resulting in possible damage.  
Small black dots or white dots (bright dots)  
may appear on the LCD screen. These are  
due to the characteristics of the LCD  
screen and do not indicate a malfunction.  
When using a cellular phone, keep the an-  
tenna away from the display to prevent dis-  
ruption of the video image by the  
In order to use Bluetooth wireless technology,  
devices must be able to interpret certain pro-  
files. This unit is compatible with the following  
profiles.  
!
!
!
!
!
!
!
GAP (Generic Access Profile)  
SDP (Service Discovery Protocol)  
OPP (Object Push Profile)  
HFP (Hands Free Profile)  
HSP (Head Set Profile)  
PBAP (Phone Book Access Profile)  
A2DP (Advanced Audio Distribution Pro-  
file)  
appearance of spots, colored stripes, etc.  
!
AVRCP (Audio/Video Remote Control Pro-  
file) 1.3  
LED (light-emitting diode)  
backlight  
!
At low temperatures, using the LED back-  
light may increase image lag and degrade  
the image quality due to the characteristics  
of the LCD screen. Image quality will im-  
prove with an increase in temperature.  
To protect the LED backlight, the display  
will darken in the following environments:  
In the direct sunlight  
Copyright and trademark  
This item incorporates copy protection tech-  
nology that is protected by U.S. patents and  
other intellectual property rights of Rovi  
Corporation. Reverse engineering and disas-  
sembly are prohibited.  
!
Bluetooth  
Near the heater vent  
The Bluetoothâ word mark and logos are regis-  
tered trademarks owned by Bluetooth SIG, Inc.  
and any use of such marks by PIONEER COR-  
PORATION is under license. Other trademarks  
and trade names are those of their respective  
owners.  
!
!
The product lifetime of the LED backlight is  
more than 10 000 hours. However, it may  
decrease if used in high temperatures.  
If the LED backlight reaches the end of its  
product lifetime, the screen will become  
dark and the image will no longer be pro-  
jected. In such cases, please consult your  
dealer or the nearest authorized PIONEER  
Service Station.  
!
Bluetooth is a short-range wireless radio  
connectivity technology that is developed  
as a cable replacement for mobile phones,  
handheld PCs and other devices. Bluetooth  
operates in 2.4 GHz frequency range and  
transmits voice and data at speeds up to 1  
megabit per second. Bluetooth was  
Keeping the display in good  
condition  
!
launched by a special interest group (SIG)  
that comprises of Ericsson Inc., Intel Corp.,  
Nokia Corp., Toshiba and IBM in 1998, and  
it is currently developed by nearly 2 000  
companies worldwide.  
When removing dust from the screen or  
cleaning the display, first turn the system  
power off, then wipe with a soft dry cloth.  
When wiping the screen, take care not to  
scratch the surface. Do not use harsh or  
abrasive chemical cleaners.  
!
104  
En  
 
Appendix  
Additional information  
DVD video  
Dolby Digital  
is a trademark of DVD Format/Logo  
Licensing Corporation.  
Manufactured under license from Dolby  
Laboratories. Dolbyand the double-D symbol  
are trademarks of Dolby Laboratories.  
iTunes  
Apple and iTunes are trademarks of Apple  
Inc., registered in the U.S. and other coun-  
tries.  
DivX  
DivXâ, DivX Certifiedâ and associated logos  
are trademarks of DivX, Inc. and are used  
under license.  
ABOUT DIVX VIDEO: DivXâ is a digital  
video format created by DivX, Inc. This is an of-  
ficial DivX Certifiedâ device that plays DivX  
video. Visit divx.com for more information and  
software tools to convert your files into DivX  
video.  
ABOUT DIVX VIDEO-ON-DEMAND: This  
DivX Certifiedâ device must be registered in  
order to play purchased DivX Video-on-De-  
mand (VOD) movies. To obtain your registra-  
tion code, locate the DivX VOD section in  
Menu operations. Go to vod.divx.com for more  
information on how to complete your registra-  
tion.  
MP3  
Supply of this product only conveys a license  
for private, non-commercial use and does not  
convey a license nor imply any right to use  
this product in any commercial (i.e. revenue-  
generating) real time broadcasting (terrestrial,  
satellite, cable and/or any other media), broad-  
casting/streaming via internet, intranets and/  
or other networks or in other electronic con-  
tent distribution systems, such as pay-audio or  
audio-on-demand applications. An indepen-  
dent license for such use is required. For de-  
tails, please visit  
http://www.mp3licensing.com.  
WMA  
About the SAT RADIO READY mark  
Windows Media is either a registered trade-  
mark or trademark of Microsoft Corporation in  
the United States and/or other countries.  
This product includes technology owned by  
Microsoft Corporation and cannot be used or  
distributed without a license from Microsoft  
Licensing, Inc.  
The SAT RADIO READY mark indicates that  
the Satellite Radio Tuner for Pioneer (i.e., XM  
tuner and Sirius satellite tuner which are sold  
separately) can be controlled by this unit.  
Please inquire to your dealer or nearest  
authorized Pioneer service station regarding  
the satellite radio tuner that can be connected  
to this unit. For satellite radio tuner operation,  
please refer to the satellite radio tuner owners  
manual.  
iPod & iPhone  
iPhone, iPod, iPod classic, iPod nano, and  
iPod touch are trademarks of Apple Inc., regis-  
tered in the U.S. and other countries.  
Made for iPodand Made for iPhonemean  
that an electronic accessory has been de-  
signed to connect specifically to iPod or  
iPhone, respectively, and has been certified by  
the developer to meet Apple performance  
standards. Apple is not responsible for the op-  
eration of this device or its compliance with  
safety and regulatory standards. Please note  
that the use of this accessory with iPod or  
iPhone may affect wireless performance.  
105  
En  
Appendix  
Additional information  
!
Everything worth listening to is on Sir-  
iusXM, getting over 130 channels, includ-  
ing the most commercial-free music, plus  
the best sports, news, talk and entertain-  
ment. A SiriusXM Vehicle Tuner and Sub-  
scription are required. For more  
information, visit  
http://www.siriusxm.com”  
!
Sirius, XM, SAT Radio Ready and all related  
logos and marks are trademarks of Sirius  
XM Radio, Inc. All rights reserved.  
HD Radioä Technology  
!
AVH-P4400BH and AVH-P3400BH  
HD Radio Technology manufactured under  
license from iBiquity Digital Corporation.  
U.S. and Foreign Patents. HD Radioä and  
the HD, HD Radio, and Arclogos are pro-  
prietary trademarks of iBiquity Digital Corp.  
Pandora  
Pandora is a registered trademark of Pandora  
Media, Inc.  
106  
En  
Appendix  
Additional information  
Language code chart for DVD  
Language (code), input code  
Japanese (ja), 1001  
English (en), 0514  
French (fr), 0618  
Spanish (es), 0519  
German (de), 0405  
Italian (it), 0920  
Chinese (zh), 2608  
Dutch, Flemish (nl), 1412  
Portuguese (pt), 1620  
Swedish (sv), 1922  
Russian (ru), 1821  
Korean (ko), 1115  
Greek (el), 0512  
Dzongkha (dz), 0426  
Ewe (ee), 0505  
Kurdish (ku), 1121  
Komi (kv), 1122  
Cornish (kw), 1123  
Kirghiz, Kyrgyz (ky), 1125  
Latin (la), 1201  
Luxembourgish (lb), 1202  
Ganda (lg), 1207  
Limburgan (li), 1209  
Lingala (ln), 1214  
Kinyarwanda (rw), 1823  
Sanskrit (sa), 1901  
Sardinian (sc), 1903  
Sindhi (sd), 1904  
Northern Sami (se), 1905  
Sangho (sg), 1907  
Sinhala (si), 1909  
Slovak (sk), 1911  
Slovenian (sl), 1912  
Samoan (sm), 1913  
Shona (sn), 1914  
Somali (so), 1915  
Albanian (sq), 1917  
Serbian (sr), 1918  
Swati (ss), 1919  
Esperanto (eo), 0515  
Estonian (et), 0520  
Basque (eu), 0521  
Persian (fa), 0601  
Fulah (ff), 0606  
Finnish (fi), 0609  
Fijian (fj), 0610  
Faroese (fo), 0615  
Western Frisian (fy), 0625  
Irish (ga), 0701  
Gaelic (gd), 0704  
Galician (gl), 0712  
Guarani (gn), 0714  
Gujarati (gu), 0721  
Manx (gv), 0722  
Hausa (ha), 0801  
Hebrew (he), 0805  
Hindi (hi), 0809  
Hiri Motu (ho), 0815  
Croatian (hr), 0818  
Haitian (ht), 0820  
Hungarian (hu), 0821  
Armenian (hy), 0825  
Herero (hz), 0826  
Interlingua (ia), 0901  
Indonesian (id), 0904  
Interlingue (ie), 0905  
Igbo (ig), 0907  
Lao (lo), 1215  
Lithuanian (lt), 1220  
Luba-Katanga (lu), 1221  
Latvian (lv), 1222  
Malagasy (mg), 1307  
Marshallese (mh), 1308  
Maori (mi), 1309  
Macedonian (mk), 1311  
Malayalam (ml), 1312  
Mongolian (mn), 1314  
Marathi (mr), 1318  
Malay (ms), 1319  
Maltese (mt), 1320  
Burmese (my), 1325  
Nauru (na), 1401  
Bokmal (nb), 1402  
Ndebele, North (nd), 1404  
Nepali (ne), 1405  
Ndonga (ng), 1407  
Nynorsk (nn), 1414  
Norwegian (no), 1415  
Ndebele, South (nr), 1418  
Afar (aa), 0101  
Abkhazian (ab), 0102  
Avestan (ae), 0105  
Afrikaans (af), 0106  
Akan (ak), 0111  
Amharic (am), 0113  
Aragonese (an), 0114  
Arabic (ar), 0118  
Sotho, Southern (st), 1920  
Sundanese (su), 1921  
Swahili (sw), 1923  
Tamil (ta), 2001  
Telugu (te), 2005  
Tajik (tg), 2007  
Assamese (as), 0119  
Avaric (av), 0122  
Thai (th), 2008  
Tigrinya (ti), 2009  
Turkmen (tk), 2011  
Tagalog (tl), 2012  
Tswana (tn), 2014  
Tonga (to), 2015  
Turkish (tr), 2018  
Tsonga (ts), 2019  
Tatar (tt), 2020  
Aymara (ay), 0125  
Azerbaijani (az), 0126  
Bashkir (ba), 0201  
Belarusian (be), 0205  
Bulgarian (bg), 0207  
Bihari (bh), 0208  
Bislama (bi), 0209  
Bambara (bm), 0213  
Bengali (bn), 0214  
Tibetan (bo), 0215  
Breton (br), 0218  
Sichuan Yi (ii), 0909  
Inupiaq (ik), 0911  
Ido (io), 0915  
Icelandic (is), 0919  
Inuktitut (iu), 0921  
Javanese (jv), 1022  
Georgian (ka), 1101  
Kongo (kg), 1107  
Twi (tw), 2023  
Navajo, Navaho (nv), 1422 Tahitian (ty), 2025  
Chichewa (ny), 1425  
Occitan (oc), 1503  
Ojibwa (oj), 1510  
Oromo (om), 1513  
Oriya (or), 1518  
Ossetian (os), 1519  
Panjabi, Punjabi (pa),  
1601  
Uighur, Uyghur (ug), 2107  
Ukrainian (uk), 2111  
Urdu (ur), 2118  
Uzbek (uz), 2126  
Venda (ve), 2205  
Vietnamese (vi), 2209  
Bosnian (bs), 0219  
Catalan (ca), 0301  
Chechen (ce), 0305  
Chamorro (ch), 0308  
Corsican (co), 0315  
Kikuyu, Gikuyu (ki), 1109  
Volapük (vo), 2215  
Cree (cr), 0318  
Czech (cs), 0319  
Church Slavic (cu), 0321  
Chuvash (cv), 0322  
Welsh (cy), 0325  
Kuanyama (kj), 1110  
Kazakh (kk), 1111  
Kalaallisut (kl), 1112  
Central Khmer (km), 1113  
Kannada (kn), 1114  
Pali (pi), 1609  
Walloon (wa), 2301  
Wolof (wo), 2315  
Xhosa (xh), 2408  
Yiddish (yi), 2509  
Yoruba (yo), 2515  
Zhuang, Chuang (za),  
2601  
Polish (pl), 1612  
Pashto, Pushto (ps), 1619  
Quechua (qu), 1721  
Romansh (rm), 1813  
Danish (da), 0401  
Kanuri (kr), 1118  
Rundi (rn), 1814  
Divehi (dv), 0422  
Kashmiri (ks), 1119  
Romanian (ro), 1815  
Zulu (zu), 2621  
107  
En  
 
Appendix  
Additional information  
Preout maximum output level  
..................................................... 4.0 V  
(AVH-P4400BH)  
Specifications  
General  
Preout maximum output level  
..................................................... 2.0 V  
(AVH-P3400BH/AVH-P2400BT/AVH-P1400DVD)  
Equalizer (8-Band Graphic Equalizer):  
Frequency .......................... 40 Hz/80 Hz/200 Hz/400 Hz/  
1 kHz/2.5 kHz/8 kHz/10 kHz  
Power source ............................. 14.4 V DC (10.8 V to 15.1 V  
allowable)  
Grounding system ................... Negative type  
Maximum current consumption  
..................................................... 10.0 A  
Dimensions (W × H × D):  
Gain ...................................... 12 dB  
HPF:  
D
Chassis ..................... 178 mm × 100 mm ×  
165 mm  
Frequency .......................... 50 Hz/63 Hz/80 Hz/100 Hz/  
125 Hz  
(7 in. × 3-7/8 in. × 6-1/2 in.)  
Slope .................................... 12 dB/oct  
Subwoofer (mono):  
Nose ........................... 171 mm × 97 mm × 18 mm  
(6-3/4 in.× 3-7/8 in.× 3/4 in.)  
Frequency .......................... 50 Hz/63 Hz/80 Hz/100 Hz/  
125 Hz  
Slope .................................... 18 dB/oct  
Gain ...................................... +6 dB to 24 dB  
Phase .................................. Normal/Reverse  
Bass boost:  
(AVH-P4400BH)  
Nose ........................... 171 mm × 97 mm × 9 mm  
(6-3/4 in. × 3-7/8 in. × 3/8 in.)  
(AVH-P3400BH/AVH-P2400BT/AVH-P1400DVD)  
Weight .......................................... 2.0 kg (4.4 lbs)  
(AVH-P4400BH)  
Gain ...................................... +12 dB to 0 dB  
Weight .......................................... 1.7 kg (3.7 lbs)  
(AVH-P3400BH/AVH-P2400BT/AVH-P1400DVD)  
DVD Player  
System .......................................... DVD video, Video CD, CD,  
WMA, MP3, AAC, DivX,  
Display  
Screen size/aspect ratio ....... 6.95 inch wide/16:9  
(effective display area:  
JPEG, MPEG system  
Usable discs .............................. DVD video, Video CD, CD,  
CD-R/RW, DVD-R/RW/R DL  
Region number ........................ 1  
Frequency response ............... 5 Hz to 44 000 Hz (with DVD,  
at sampling frequency  
156.4 mm × 81.7 mm)  
(AVH-P4400BH)  
Screen size/aspect ratio ....... 5.8 inch wide/16:9  
(effective display area:  
128.4 mm × 70.9 mm)  
96 kHz)  
(AVH-P3400BH/AVH-P2400BT/AVH-P1400DVD)  
Pixels ............................................. 345 600 (1 440 × 240)  
Display method ........................ TFT active matrix, driving  
type  
Signal-to-noise ratio ............... 96 dB (1 kHz) (IHF-A net-  
work) (RCA level)  
(AVH-P4400BH)  
Signal-to-noise ratio ............... 91 dB (1 kHz) (IHF-A net-  
work) (RCA level)  
Color system .............................. NTSC/PAL/PAL-M/PAL-N/  
SECAM compatible  
(AVH-P3400BH/AVH-P2400BT/AVH-P1400DVD)  
Output level:  
Durable temperature range (power off)  
..................................................... 20 °C to +80 °C  
Video .................................... 1.0 Vp-p/75 W ( 0.2 V)  
Number of channels .............. 2 (stereo)  
MP3 decoding format ........... MPEG-1 & 2 Audio Layer 3  
WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11, 12  
(2 ch audio)  
(Windows Media Player)  
AAC decoding format ............ MPEG-4 AAC (iTunes en-  
coded only) (.m4a)  
Audio  
Maximum power output ....... 50 W × 4  
70 W × 1/2 W (for subwoo-  
fer)  
Continuous power output ... 22 W × 4 (50 Hz to  
15 000 Hz, 5 % THD,  
4 W load, both channels dri-  
ven)  
(Ver. 9.0.3 and earlier)  
DivX decoding format ............ Home Theater Ver. 3, 4, 5.2,  
6 (.avi, .divx)  
MPEG video decoding format  
Load impedance ...................... 4 W (4 W to 8 W (2 W for 1 ch)  
allowable)  
..................................................... MPEG1, MPEG2, MPEG4  
108  
En  
 
Appendix  
Additional information  
USB  
USB standard specification  
..................................................... USB 1.1, USB 2.0 full speed  
Maximum current supply .... 1.0 A  
USB Class ................................... MSC (Mass Storage Class)  
File system .................................. FAT16, FAT32  
MP3 decoding format ........... MPEG-1 & 2 Audio Layer 3  
WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11, 12  
(2 ch audio)  
(Windows Media Player)  
AAC decoding format ............ MPEG-4 AAC (iTunes en-  
coded only)  
(Ver. 9.0.3 and earlier)  
DivX decoding format ............ Home Theater Ver. 3, 4, 5.2,  
6 (.avi, .divx)  
MPEG video decoding format  
..................................................... MPEG1, MPEG2, MPEG4  
FM tuner  
Frequency range ...................... 87.9 MHz to 107.9 MHz  
Usable sensitivity ..................... 9 dBf (0.8 µV/75 W, mono,  
S/N: 30 dB)  
Signal-to-noise ratio ............... 72 dB (IHF-A network)  
AM tuner  
Frequency range ...................... 530 kHz to 1 710 kHz  
(10 kHz)  
Usable sensitivity ..................... 25 µV (S/N: 20 dB)  
Signal-to-noise ratio ............... 62 dB (IHF-A network)  
Bluetooth  
(AVH-P4400BH/AVH-P3400BH/AVH-P2400BT)  
Version .......................................... Bluetooth 3.0 certified  
Output power ............................ +4 dBm Maximum  
(Power class 2)  
CEA2006 Specifications  
Power output ............................. 14 W RMS × 4 Channels  
(4 W and 1 % THD+N)  
S/N ratio ....................................... 91 dBA (reference: 1 W into  
4 W)  
Note  
Specifications and the design are subject to mod-  
ifications without notice.  
109  
En  
110  
En  
111  
En  
PIONEER CORPORATION  
1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi,  
Kanagawa 212-0031, JAPAN  
PIONEER ELECTRONICS (USA) INC.  
P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.  
TEL: (800) 421-1404  
PIONEER EUROPE NV  
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique  
TEL: (0) 3/570.05.11  
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.  
253 Alexandra Road, #04-01, Singapore 159936  
TEL: 65-6472-7555  
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.  
5 Arco Lane, Heatherton, Victoria, 3202 Australia  
TEL: (03) 9586-6300  
PIONEER ELECTRONICS OF CANADA, INC.  
340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada  
TEL: 1-877-283-5901  
TEL: 905-479-4411  
PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.  
Blvd.Manuel Avila Camacho 138 10 piso  
Col.Lomas de Chapultepec, Mexico, D.F. 11000  
TEL: 55-9178-4270  
 
台北4078  
(02) 2657-3588  
司  
9095樓  
(0852) 2848-6488  
ã 2011 PIONEER CORPORATION.  
All rights reserved.  
Printed in China  
<KNAZX> <11K00000>  
<CRB3728-A/U> UC  

Radio Shack 200 User Manual
Pioneer AVH P1400DVD User Manual
Philips SPORTS ARMBAND SJM2007 User Manual
Panasonic HC X910 User Manual
Panasonic AW RC600 User Manual
Omega OFS20 User Manual
Metrik Mobile Electronics MCD 476 User Manual
Lightning Audio Bolt b22501 B22501 User Manual
Kenwood KX W8050 User Manual
Kenwood Car Stereo System TS B2000 User Manual