Philips Bluetooth Headset SHB7150 User Manual

Always there to help you  
Register your product and get support at  
SHB7150  
Question?  
Contact  
Philips  
User manual  
Caution  
1 Important safety  
instructions  
Do not expose the headset to excessive heat.  
Do not drop your headset.  
Headset shall not be exposed to dripping or splashing.  
Do not allow your headset to be submerged in water.  
Do not use any cleaning agents containing alcohol,  
ammonia, benzene, or abrasives.  
If cleaning is required use a soft cloth, if necessary  
dampened with a minimum amount of water or diluted  
mild soap, to clean the product.  
The integrated battery shall not be exposed to  
excessive heat such as sunshine, fire or the like.  
Hearing Safety  
About operating and storage temperatures  
and humidity  
Operate or store in a place where  
temperature is between -15ºC (5ºF) and  
55ºC (131ºF) (up to 90% relative humidity.  
Battery life may be shorter in high or low  
temperature conditions.  
Danger  
To avoid hearing damage, limit the time you use the  
headset at high volume and set the volume to a safe  
level.The louder the volume, the shorter the safe  
listening time is.  
Be sure to observe the following guidelines  
when using your headset.  
Compliance with EMF  
Listen at reasonable volumes for  
reasonable periods of time.  
This product complies with all applicable  
standards and regulations regarding exposure to  
electromagnetic fields.  
Be careful not to adjust the volume  
continuously upwards as your hearing  
adapts.  
Do not turn up the volume so high that  
you can’t hear what’s around you.  
You should use caution or temporarily  
discontinue use in potentially hazardous  
situations.  
Excessive sound pressure from earphones  
and headset can cause hearing loss.  
Using the headset with both ears covered  
while driving is not recommended and may  
be illegal in some areas while driving.  
For your safety, avoid distractions from  
music or phone calls while in traffic or  
other potentially dangerous environments.  
General information  
To avoid damage or malfunction:  
2
EN  
       
2 Your Bluetooth  
stereo headset  
Congratulations on your purchase, and  
welcome to Philips!To fully benefit from the  
support that Philips offers, register your product  
With this Philips wireless on-ear headset, you  
can:  
Quick start guide  
Other devices  
A mobile phone or device (e.g. notebook, PDA,  
Bluetooth adapters, MP3 players etc) which  
supports Bluetooth and is compatible to the  
headset.  
enjoy convenient wireless handsfree calls;  
enjoy and control wireless music;  
switch between calls and music;  
enjoy music on non-Bluetooth devices with  
an audio cable.  
What's in the box  
Philips Bluetooth stereo headset SHB7150  
USB charging cable  
Audio cable  
EN  
3
     
Overview of your Bluetooth  
stereo headset  
a Microphone  
b
Call/Music button  
c Audio input jack  
d Volume/Track control  
e Charging slot  
4
EN  
 
There are two ways to pair your headset with  
your mobile phone:  
3 Get started  
Manual pairing  
NFC pairing  
Manual pairing  
Charge your headset  
1 Make sure that the mobile phone is turned  
on and its Bluetooth feature is activated.  
Note  
2 Make sure that the headset is fully charged  
Before you use your headset for the first time, charge  
the battery for 4 hours for optimum battery capacity  
and lifetime.  
Use only the original USB charging cable to avoid any  
damage.  
and turned off.  
3 Press and hold until the blue and white  
LED flashes alternately.  
Finish your call before charging the headset, as  
connecting the headset for charging will power the  
headset off.  
» The headset remains in pairing mode  
for 2 minutes.  
4 Pair the headset with the mobile phone.  
For detailed information, refer to the user  
manual of your mobile phone.  
Connect the supplied USB charging cable to:  
the USB connector of the headset and;  
USB power source.  
» LED turns white during charging and  
turns off when the headset is fully  
charged.  
NFC pairing  
1 Make sure that the mobile phone is turned  
on.  
2 Make sure that the headset is fully charged  
Tip  
and turned off.  
Normally, a full charge takes 3 hours.  
3 Press and hold until the blue and white  
When your battery is empty, you can carry on listening  
music with an audio cable. Make sure the headset is off  
(and not in idle mode) before using this audio cable.  
LED flashes alternately..  
4 Make sure you turn on the NFC function  
on your phone and your phone’s screen  
remains active.  
5 Place your phone over the headset so that  
the NFC detection area of each device can  
touch each other.  
Pair the headset with your  
mobile phone  
Before you use the headset with your mobile  
phone for the first time, pair it with a mobile  
phone.A successful pairing establishes a unique  
encrypted link between the headset and mobile  
phone.The headset stores the last 8 devices  
in the memory. If you try to pair more than 8  
devices, the earliest paired device is replaced by  
the new one.  
Note  
Make sure your mobile phone has the NFC feature  
available and switched on.  
Make sure your mobile phone is not in standby mode.  
Pairing with NFC is only suitable for Android mobile  
operating system 4.2 or above.  
Refer to the user manual of your mobile phone to  
identify its NFC detection area.  
EN  
5
     
The following example shows you how to pair  
the headset with your mobile phone.  
1 Activate the Bluetooth feature of your  
mobile phone, select Philips SHB7150.  
2 Enter the headset password "0000" (4  
zeros) if prompted. For those mobile  
phones featuring Bluetooth 3.0 or higher,  
no need to enter a password.  
10:35  
10:36  
10:37  
Settings  
Connectivity  
Settings  
Settings  
Connectivity  
Bluetooth  
Devices Found  
Enter Password  
****  
Add  
Bluetooth  
device  
Philips SHB7150  
0000  
Select  
Back  
Select  
Back  
Select  
Back  
6
EN  
Turn the headset Press and  
4 beeps  
White  
LED  
flashes  
N/A  
4 Use your  
headset  
off.  
hold for 4  
seconds.  
Play or pause  
music.  
Pick up/hang up  
a call.  
Press once.  
Press once.  
Connect the headset to a  
Bluetooth device  
1 beep  
Reject an  
incoming call.  
Press and  
hold for 1  
second.  
1 long beep  
1 Turn on your mobile phone/Bluetooth  
device.  
Redial the last  
number.  
Switch caller  
during a call.  
Press twice.  
2 beeps  
1 beep  
2 Press and hold to turn the headset on.  
» The blue LED flashes.  
Press once  
» The headset is reconnected to  
the last connected mobile phone/  
Bluetooth device automatically. If the  
last one is not available, the headset  
tries to reconnect to the second last  
connected device.  
Volume/Track control button  
Adjust volume.  
Slide up/  
down  
N/A  
Skip forward.  
Skip backward.  
Mute/unmute the micro- Press once  
phone in a call.  
Press once  
Press twice  
N/A  
N/A  
1
Tip  
If you turn on the mobile phone/Bluetooth device or  
activate the Bluetooth feature after turning on the  
headset, you have to reconnect the headset and mobile  
phone/Bluetooth device manually.  
beep  
Other headset indicator status  
Headset status  
The headset is connected  
Indicator  
Blue LED flashes  
Note  
to a Bluetooth device, while for every 8  
If the headset fails to connect to any Bluetooth device  
within range in 5 minutes, it will switch off automatically  
to save the battery life.  
the headset in standby  
mode or while you are  
listening to music.  
The headset is ready for  
pairing.  
seconds.  
LED flashes  
blue and white  
alternately.  
Manage your calls and music  
The headset is on but not  
connected to a Bluetooth  
device.  
Blue LED flashes  
quickly.  
Call/Music button  
There is an incoming call.  
Blue LED flashes  
once per second.  
White LED  
flashes.  
White LED is off.  
Task  
Operation  
Sound  
or LED  
indicator  
4 beeps  
Blue LED  
flashes.  
Low battery.  
Turn the headset Press and  
on.  
Battery is fully charged.  
hold for 1  
second.  
EN  
7
     
Wear your headset  
Adjust the headband to fit your head.  
Tip  
After use, twist the headset for easy storage.  
Use with the audio cable  
Note  
Make sure that you turn off the Bluetooth headset  
before connecting the audio cable.  
With the supplied audio cable, you can use  
the headset with non-Bluetooth devices or on  
airplane. No battery power is required for the  
headset when you use it with the audio cable.  
Connect the supplied audio cable to  
the headset and;  
an external audio device.  
8
EN  
   
5 Technical data  
Minimum 9 hours of music time or talk  
time  
Minimum 200 hours of standby time  
Normal time for a full charge: 3 hours  
Rechargeable Lithium-Polymer battery  
(200 mAh)  
3.5 mm audio jack for corded headset  
mode  
Bluetooth 3.0, Bluetooth mono support  
(Headset Profile - HSP, Hands-Free  
Profile - HFP), Bluetooth stereo supported  
(Advanced Audio Distribution Profile  
- A2DP;AudioVideo Remote Control  
Profile - AVRCP)  
Operating range: Up to 15 meters (50  
feet)  
Digital echo & noise reduction  
Auto power off  
Note  
Specifications are subject to change without notice.  
EN  
9
 
6 Notice  
Your product contains batteries covered by the  
European Directive 2006/66/EC, which cannot  
be disposed with normal household waste.  
Please inform yourself about the local rules  
on separate collection of batteries because  
correct disposal helps to prevent negative  
consequences for the environmental and  
human health.  
Declaration of conformity  
Hereby,WOOX Innovations declares that this  
product is in compliance with the essential  
requirements and other relevant provisions  
of Directive 1999/5/EC.You can find the  
com.  
This product has been designed, tested and  
manufactured according the European R&TTE  
directive 1999/5/EC.  
Remove the integrated battery  
Note  
Make sure the headset is disconnected from the USB  
charging cable before removing the battery.  
Disposal of your old product  
and batteries  
If there is no collection/recycling system for  
electronic products in your country, you can  
protect the environment by removing and  
recycling the battery before disposing the  
headset.  
Your product is designed and manufactured  
with high quality materials and components,  
which can be recycled and reused.  
a
b
When this crossed-out wheeled bin symbol is  
attached to a product it means that the product  
is covered by the European Directive 2002/96/  
EC. Please inform yourself about the local  
separate collection system for electrical and  
electronic products.  
c
d
Please act according to your local rules and  
do not dispose of your old products with your  
normal household waste.  
Correct disposal of your old product helps to  
prevent potential negative consequences for the  
environment and human health.  
Environmental information  
All unnecessary packaging has been omitted.  
We have tried to make the packaging easy to  
separate into three materials: cardboard (box),  
10 EN  
     
polystyrene foam (buffer) and polyethylene  
(bags, protective foam sheet.)  
Your system consists of materials which can  
be recycled and reused if disassembled by  
a specialized company. Please observe the  
local regulations regarding the disposal of  
packaging materials, exhausted batteries and old  
equipment.  
Notice for the European  
Union  
0168  
Hereby,WOOX Innovations declares that this  
product is in compliance with the essential  
requirements and other relevant provisions of  
Directive 1999/5/EC.  
Trademarks  
2013 © WOOX Innovations Limited.All rights  
reserved.  
Philips and the Philips’ Shield Emblem are  
registered trademarks of Koninklijke Philips N.V.  
and are used by WOOX Innovations Limited  
under license from Koninklijke Philips N.V.  
Bluetooth  
The Bluetooth word mark and logos are owned  
by the Bluetooth SIG, Inc. and any use of such  
marks by WOOX Innovations Limited is under  
license.  
EN 11  
   
My Bluetooth headset is connected to a  
7 Frequently  
Bluetooth stereo enabled mobile phone, but  
music only plays on the mobile phone speaker.  
Refer to the user manual of your mobile phone.  
Select to listen to music through the headset.  
asked questions  
My Bluetooth headset does not switch on.  
The battery level is low. Charge the headset.  
The audio quality is poor and crackling noise  
can be heard.  
The Bluetooth device is out of range. Reduce  
the distance between your headset and  
Bluetooth device, or remove obstacles between  
them.  
I cannot pair my Bluetooth headset with a  
mobile phone.  
The Bluetooth is disabled. Enable the Bluetooth  
feature on your mobile phone and turn on the  
mobile phone before you turn on the headset.  
The audio quality is poor when streaming  
from the mobile phone is very slow, or audio  
streaming does not work at all.  
Make sure your mobile phone not only  
supports (mono) HSP/HFP but also supports  
A2DP (see 'Technical data' on page 9).  
Pairing does not work.  
Make sure the headset is in pairing mode.  
manual (see 'Pair the headset with your  
mobile phone' on page 5).  
Make sure that the LED light flashes blue  
and white alternately before you release  
the call/music button. Do not stop holding  
the button if you see the blue LED only.  
I hear but cannot control music on my  
Bluetooth device (e.g. play/pause/skip forward/  
backward).  
Make sure the Bluetooth audio source supports  
AVRCP (see 'Technical data' on page 9).  
The mobile phone cannot find the headset.  
The headset may be connected to a  
previously paired device.Turn off the  
connected device or move it out of range.  
Pairing may have been reset or the headset  
has been previously paired with another  
device. Pair the headset with the mobile  
phone again as described in the user  
manual (see 'Pair the headset with your  
mobile phone' on page 5).  
My headset does not work when the audio  
cable is connected.  
Microphone function will be deactivated if a  
3.5mm audio cable is connected to the headset.  
In such case, your headset is only for music  
enjoyment.  
How can I restore all original headset settings?  
When the headset is powered off, press and  
hold the Call/Music button for 10 seconds.The  
headset is powered ON, entered the pairing  
mode and then powered off.The factory setting  
is reset.  
Voice dialing or redialing does not work on  
my mobile phone.  
Your mobile phone may not support this  
feature.  
support.  
The other side cannot hear me on the mobile  
phone.  
The microphone is muted. Press volume/track  
control button once to enable the microphone.  
12 EN  
 
Specifications are subject to change without notice  
2013 ©WOOX Innovations Limited.All rights  
reserved.  
SHB7150_UM_EN_V1.0  

Profoto D1 250 AIR User Manual
Pioneer BDR 207DBK Internal Blu ray Writer BDR 207DBK User Manual
Panasonic SDR S26 User Manual
Panasonic Lumix DMC FH6 User Manual
Magnadyne M5000CD User Manual
Listen Technologies DCN LA 334 User Manual
KitchenAid 4KHB100 User Manual
Kenwood Excelon DDX8019 User Manual
Kenwood DPX503 User Manual
Kenwood Car Video System KVT 829DVD User Manual