Operating Instructions
DVD Video Camera
Model no.
VDR-D310GN
VDR-D220GN
Before use, please read these instructions
completely.
LSQT1161 A
≥ Depending on the model, some functions are
not available.
≥ Features may vary, so please read carefully.
∫ Indemnity concerning recording
content
The manufacturer shall in no event be liable for
the loss of recordings due to malfunction or
defect of this unit, its accessories or recordable
media.
∫ Carefully observe copyright laws
Recording of pre-recorded tapes or discs or
other published or broadcast material for
purposes other than your own private use
may infringe copyright laws. Even for the
purpose of private use, recording of certain
material may be restricted.
≥ SDHC Logo is a trademark.
≥ miniSD Logo is a trademark.
≥ The Movie Camera uses copyright-protected
technologies and is protected by the patented
technologies and intellectual properties of
Japan and the U.S. To use these copyright-
protected technologies, authorization of the
Macrovision Company is required. It is
prohibited to disassemble or modify the Movie
Camera.
≥ Manufactured under license from Dolby
Laboratories.
“Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
≥ LEICA is a registered trademark of Leica
microsystems IR GmbH and DICOMAR is a
registered trademark of Leica Camera AG.
≥ Other names of systems and products
mentioned in these instructions are usually the
registered trademarks or trademarks of the
manufacturers who developed the system or
product concerned.
These operating instructions are designed for
use with models VDR-D310 and VDR-D220.
Pictures may be slightly different from the
original.
≥ The illustrations used in these operating
instructions show model VDR-D310, however,
parts of the explanation refer to different
models.
3
LSQT1161
Soft skin mode ......................................... 49
Tele macro function (VDR-D310)............. 49
Colour night view function........................ 50
Self-timer recording.................................. 50
Recording guideline function.................... 51
Wide mode............................................... 51
Image stabilizer function .......................... 51
Wind noise reduction function.................. 52
Manual recording functions................52
Scene mode............................................. 52
Manual focus adjustment......................... 53
White balance .......................................... 54
Manual shutter speed/
Contents
Information for Your Safety...................2
Before using
Features ..................................................6
Accessories............................................8
Parts identification and handling .........9
Using the LCD monitor.............................12
Using the viewfinder.................................13
Using the remote control (VDR-D310) .....13
Discs and cards....................................15
Discs that can be used on this unit...........15
Cards that you can use with this unit........19
Disc and card handling.............................20
aperture adjustment................................. 55
Playback
Motion picture playback......................57
Still picture playback
(JPEG still pictures).............................61
Setup
Power supply........................................21
Charging the battery.................................21
Connecting to the AC outlet .....................25
Turning the unit on/off...............................25
Inserting/removing a disc....................26
Inserting/removing an SD card...........28
Selecting a mode..................................29
How to use the joystick .......................29
Switching the language.......................33
Using the menu screen........................33
Setting date and time...........................35
Adjusting LCD monitor/
Editing
Editing scenes......................................63
Deleting scenes ....................................... 63
Dividing a scene....................................... 64
Combining scenes ................................... 64
Using playlists......................................65
What is a playlist?.................................... 65
Creating a new playlist............................. 65
Playing back a playlist.............................. 66
Editing a playlist....................................... 66
Editing still pictures.............................70
Deleting still pictures................................ 70
Locking still pictures................................. 71
DPOF setting ........................................... 71
viewfinder .............................................36
Recording
Disc and card management
Before recording ..................................37
Recording motion pictures .................39
Recording modes and recordable time
available for the motion picture ................40
Recording still pictures
Disc management ................................73
Finalizing a disc ....................................... 73
Un-finalizing a DVD-RW .......................... 74
Protecting a disc ...................................... 74
Formatting discs....................................... 74
Displaying disc information ...................... 75
Card management................................75
Formatting an SD card............................. 75
(JPEG still pictures).............................42
Number of pixels and picture quality
for still picture recording ...........................45
Various recording functions ...............46
Zoom in/out function.................................46
Recording yourself ...................................47
Backlight compensation function..............47
Fade in/fade out function..........................48
4
LSQT1161
With other products
With a TV...............................................77
Playback on TV ........................................77
With a DVD recorder/player.................78
Playback on DVD recorder,
DVD player, computer etc. .......................78
Dubbing recordings
onto a DVD recorder’s hard disk ..............79
With a VCR............................................80
Dubbing images
onto other video devices ..........................80
With a printer (PictBridge)...................80
Others
Menus....................................................83
Menu list...................................................83
Other menus.............................................84
Indications ............................................85
Indications ................................................85
Messages.................................................88
Functions that cannot be used
simultaneously..........................................90
Frequently asked questions................91
Troubleshooting...................................92
Cautions for use...................................96
Explanation of terms............................99
Specifications.....................................101
Number of recordable pictures
on an SD card ........................................103
5
LSQT1161
Before using
Before using
Features
∫ Easy recording! (l 39)
No need to search for the recording start position.
The new recording will not overwrite any previously recorded scene.
∫ Easy playback! (l 57)
Recorded scenes are displayed as thumbnails.
You can easily search for the scenes you want to watch.
∫ Editing scenes! (l 63, 65)
You can create an original video (playlist) by collecting your favourite scenes together and then easily
dub this video to a VCR or a DVD recorder hard disk.
6
LSQT1161
Before using
If you insert a DVD-RW or a DVD-R disc recorded in this unit (that has not been finalized) into
another device such as DVD recorder, computer, etc., the disc may become unusable.
Be sure to finalize the disc on this unit before inserting it in other devices. (l 73)
∫ Using with DVD player/recorder! (l 78)
Just insert the disc into a DVD player/recorder compatible with 8 cm discs to play back the scenes
recorded with this unit on it.
If you have a DVD recorder with hard disk, you can dub scenes recorded on a disc with this unit to the
hard disk.
∫ Using with a computer! (VDR-D310) (Refer to the operating instructions
for PC connection.)
You can enjoy editing scenes with the software on the supplied CD-ROM and creating original
DVD-Video discs.
7
LSQT1161
Before using
Accessories
Optional accessories
Check the accessories before using this unit.
Some optional accessories may not be available
in some countries.
Battery pack
(VDR-D310)
AC adaptor (VW-AD11GN)
Battery pack
(VDR-D220)
Battery pack (lithium/CGR-DU06/640 mAh)
(VDR-D220)
AC adaptor
DC cable
Battery pack (lithium/CGA-DU12/1150 mAh)
Battery pack (lithium/CGA-DU14/1360 mAh)
Battery pack (lithium/CGA-DU21/2040 mAh)
Wide conversion lens (VW-LW3707M3E)
(VDR-D310)
AV/S cable
AC cable
Tele conversion lens (VW-LT3714ME)
(VDR-D310)
Filter kit (VW-LF37WE)
Video DC light (VW-LDC10E)
Light bulb for video DC light (VZ-LL10E)
Remote control
(VDR-D310)
Button-type battery
(VDR-D310)
Stereo microphone (VW-VMS2E)
(VDR-D310)
Tripod (VW-CT45E)
Lens cap
8 cm DVD-RAM disc (single sided/LM-AF30E)
8 cm DVD-RAM disc (double sided/
LM-AF60E)
USB cable
8 cm DVD-RW disc (single sided/LM-RW30E)
(VDR-D310)
8 cm DVD-RW disc (double sided/
LM-RW60E)
CD-ROM
8 cm DVD-R disc (single sided/LM-RF30E)
8 cm DVD-R disc (double sided/LM-RF60E)
(VDR-D310)
Disc cleaning cloth
8 cm DVD-R DL disc (dual layer on single
side/LM-RF55LE)
8
LSQT1161
Before using
connection.)
Disc access lamp [ACCESS/PC]
(VDR-D220) (l 26)
Parts identification and
handling
13 Mode dial (l 29)
14 Joystick (l 29)
15 Recording start/stop button (l 39)
16 Disc eject lever [DISC EJECT] (l 26)
1
17 18
2
3
1
Lens (LEICA DICOMAR) (VDR-D310)
Lens (VDR-D220)
2
3
Microphone (built-in, stereo)
White balance sensor (l 55)
Remote control sensor (VDR-D310) (l 14)
19
20
17 When recording: Zoom lever [W/T] (l 46)
When playing back: Volume lever
[sVOLr] (l 59)
10
11
4
18 Photoshot button [
] (l 42)
19 Accessory shoe
≥ Accessories, such as a video DC light
(optional), are attached here.
20 Eyepiece corrector knob (l 36)
12
13
14
5
6
7
8
15
16
22
9
21
4
5
Menu button [MENU] (l 33)
Viewfinder (l 13)
Due to limitations in LCD production
technology, there may be some tiny bright
or dark spots on the viewfinder screen.
However, this is not a malfunction and
does not affect the recorded picture.
21 Tripod receptacle (l 12)
22 Battery release lever [BATTERY] (l 21)
6
7
8
9
Delete button [ ] (l 63, 67, 70)
LCD monitor open part (l 12)
DC input terminal [DC/C.C. IN] (l 25)
Battery holder (l 21)
10 Power switch [OFF/ON] (l 25)
11 Status indicator (l 25)
12 Disc/computer access lamp [ACCESS/
PC] (VDR-D310) (l 26) (Refer to the
operating instructions for PC
9
LSQT1161
Before using
27
28
34
23
24
29
30
31
32
35
25
26
33
34 Disc compartment (l 26)
35 Grip belt (l 10)
23 LCD monitor (l 12)
Using grip belt
Due to limitations in LCD production
technology, there may be some tiny bright
or dark spots on the LCD monitor screen.
However, this is not a malfunction and
does not affect the recorded picture.
Adjust the belt length so it fits your hand.
Adjust the belt length and the pad
position.
24 Terminal cover
25 Microphone terminal [MIC] (VDR-D310)
≥ A compatible plug-in powered microphone
can be used as an external microphone.
≥ When the unit is connected with the AC
adaptor, sometimes noise may be heard
depending on the microphone type. In this
case, please switch to the battery for the
power supply and the noise will stop.
26 Audio-video output terminal [A/V]
(l 77, 80)
2
1
3
1
2
3
Flip the belt.
Adjust the length.
Replace the belt.
27 Speaker
28 Mode select switch [AUTO/MANUAL/
FOCUS] (l 38, 52, 53)
29 Reset button [RESET] (l 95)
30 Card slot cover [SD CARD] (l 28)
31 Card access lamp (l 29)
32 Card slot (l 28)
33 USB terminal [ ] (l 80)
Attaching the lens cap
Attach the lens cap to protect the surface of the
lens.
≥ When the MC protector or the ND filter of the
Filter Kit (VW-LF37WE; optional) is attached,
use the lens cap included in the Filter Kit.
(Refer to the operating instructions for PC
connection.) (VDR-D310)
10
LSQT1161
Before using
1 Pass the end of the lens cap cord
through the belt.
Lens hood
∫ VDR-D310
Rotate the lens hood counter-
clockwise A to remove it.
In order to attach it, place into slot
B, and then rotate it clockwise C.
2 Pass the lens cap through the
loop.
A
B
3 To attach or remove the lens cap,
hold both sides of the lens cap
with the tips of your finger and
thumb.
C
During recording
The removed lens cap can be attached to the
lens cap fixture.
≥ Attach the MC protector or the ND filter of the
Filter Kit (VW-LF37WE; optional) in front of the
lens hood. Do not attach the other accessories
on the hood. (Except for the lens cap)
(Refer to the operating instructions for the
Filter Kit.)
≥ When attaching the tele conversion lens
(VW-LT3714ME; optional) or the wide
conversion lens (VW-LW3707M3E; optional),
first remove the lens hood.
(Refer to the operating instructions for the tele
conversion lens or the wide conversion lens.)
11
LSQT1161
Before using
≥ When 2 lens accessories, such as the ND filter
and tele conversion lens, are attached and the
W/T lever is pressed toward the W side, the 4
corners of an image will be darkened.
(Vignetting)
(Please carefully read the operating instructions
for how to attach the unit to the tripod.)
∫ VDR-D220
Rotate the lens hood counter-
clockwise A to remove it.
In order to attach it, rotate it
clockwise B.
≥ When the tripod is used, the card slot cover
cannot be opened. Insert an SD card before
attaching this unit to the tripod. (l 28)
A
Using the LCD monitor
You can record the image while viewing it on the
LCD monitor.
1 Place your finger on the LCD
monitor open part A and pull the
LCD monitor out in the direction
of the arrow.
B
≥ Do not attach the accessories on the hood.
(Except for the lens cap)
A
≥ When attaching the MC protector or the ND
filter of the Filter Kit (VW-LF37WE; optional),
first remove the lens hood.
≥ It can open up to 90o.
(Refer to the operating instructions for the
accessories.)
2 Adjust the angle of the LCD
monitor as desired.
≥ It can rotate up to 180o A towards the lens or
90o B towards the viewfinder.
Tripod receptacle
This is a hole for attaching the unit to the optional
tripod.
A
B
12
LSQT1161
Before using
≥ The brightness and colour level of the LCD
monitor can be adjusted from the menu.
(l 36)
≥ The unit may be damaged or fail if the LCD
monitor is forcibly opened or rotated.
≥ If the LCD monitor is rotated by 180x towards
the lens and the viewfinder is extended (when
recording yourself), the LCD monitor and the
viewfinder simultaneously light.
Using the remote control
(VDR-D310)
1
START/
STOP
PHOTO
SHOT
EXT
DISPLAY
7
8
2
DATE/
TIME
ZOOM
3
VOL
Using the viewfinder
SEARCH
PLAY
PAUSE
STOP
SEARCH
STILL ADV
SKIP
Pull out the viewfinder.
STILL ADV
4
SKIP
MENU
9
5
6
ENTER
10
The viewfinder will be activated. (If the LCD
monitor is opened, the viewfinder will be
deactivated.)
1
2
Photoshot button [PHOTO SHOT,
On-screen display button [EXT DISPLAY]
(l 78)
]*
≥ The brightness of the viewfinder (l 36) and
the field of view (l 36) can be adjusted.
3
4
5
6
7
Date/time button [DATE/TIME] (l 35)
Playback operation buttons (l 58)
Delete button [ ]*
Direction buttons [3,4,2,1] (l 34)
Recording start/stop button [START/
STOP]*
8
9
Zoom/volume buttons [ZOOM, VOL]*
Menu button [MENU]* (l 34)
10 Enter button [ENTER] (l 34)
* means that these buttons function in the same
manner as the corresponding buttons on the
unit.
∫ Install a button-type battery
Install the supplied button-type battery in the
remote control before using it.
13
LSQT1161
Before using
1 While pressing the stopper A,
∫ Remote control usable range
pull out the battery holder.
The distance between the remote control and the
unit’s remote control sensor A: Within approx.
5 m
Angle: Approx. 10o up and 15o down, left, and
right
A
2 Set the button-type battery with
its (r) mark facing upward and
then put the battery holder back
in place.
A
≥ The remote control is intended for indoor
operation. Outdoors or under strong light, the
unit may not operate properly even within the
usable ranges.
∫ Concerning the button-type battery
≥ When the button-type battery runs down,
replace it with a new battery (part number:
CR2025). The battery should normally last
about 1 year, however this depends on how
frequently the unit is used.
≥ Keep the button-type battery out of the reach of
children.
CAUTION
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type recommended by the
manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
Warning
Risk of fire, explosion and burns. Do not
recharge, disassemble, heat above 60 xC or
incinerate.
Warning
Keep the Button-Type battery out of the reach
of children. Never put Button-Type battery in
mouth. If swallowed call your doctor.
14
LSQT1161
Before using
Discs and cards
Discs that can be used on this unit
Disc type
DVD-RAM
8 cm
DVD-RW
8 cm
Single sided/
double sided
Single sided/double sided
(DVD-RAM
Ver. 2.1)
[DVD-RW Ver. 1.1/2X-SPEED (2X/1X)]
Recording format
DVD Video
Recording format
(VR format)
DVD Video
Recording format
(VR format)
DVD-Video format
(Video format)
Characteristic
Rewritable disc
Rewritable disc
One time recording
disc
*1
Display on the screen
Indication in these
instructions
(RAM)
(-RW‹VR›)
(-RW‹V›)
Functions
≥ Deleting recorded scenes
≥ Editing on this unit
≥ Playback on other
¥
¥
¥
¥
–
–
*3
*4
*5
¥
¥
¥
*2
products
*6
≥ Recording after finalizing
–
¥
¥
15
LSQT1161
Before using
Disc type
DVD-R
8 cm
DVD-R DL
8 cm
Single sided/double sided
Dual layer on single side
(DVD-R for General Ver. 2.0)
(DVD-R for DL Ver. 3.0)
Recording format
DVD-Video format
(Video format)
DVD-Video format
(Video format)
Characteristic
One time recording disc
One time recording disc
Display on the screen
Indication in these
instructions
(-R)
Functions
≥ Deleting recorded scenes
≥ Editing on this unit
≥ Playback on other
–
–
*5
¥
*2
products
≥ Recording after finalizing
–
¥: available –: not available
*1 By formatting the disc, it can be used repeatedly. (l 74)
*2 DVD players and DVD recorders that support 8 cm discs.
*3 Playback is possible on compatible products.
*4 Must be finalized on this unit. (l 73) Playback is possible on compatible products.
*5 Must be finalized on this unit. (l 73) Playback of DVD-R DL is possible on compatible products.
*6 Un-finalize the disc. (l 74)
16
LSQT1161
Before using
≥ For the purposes of these operating instructions, DVD-R and DVD-R DL are referred to as the
“DVD-R”.
≥ Still pictures cannot be recorded on a disc with this unit.
≥ You cannot record or play continuously from one side of the disc to the other when using a double
sided disc. You will need to eject the disc and turn it over.
≥ Discs inserted in a holder, cartridge, or caddy case cannot be used. Always remove bare discs from
these containers prior to use.
≥ It is recommended that you use Panasonic discs. Usually discs compatible with the DVD standard
can be used for recording and playback with no problems. However, some commercially available
discs do not meet the DVD standard for quality and performance. If you use one of these discs, you
may not be able to record or playback normally. (The message “FOR BEST PERFORMANCE
PANASONIC DISC IS RECOMMENDED.” appears.) Refer to the following support site for
information about discs that have been confirmed as compatible by Panasonic.
http://panasonic.co.jp/pavc/global/cs/e_cam (This website is in English only.)
≥ Discs recorded on this unit may not be playable on other products.
≥ Recording on DVD-R in DVD Video Recording format is not supported.
≥ When using DVD-RW or DVD-R, do not perform the following as it may make the disc
unusable.
jRecord on a disc with other products after recording on it with this unit.
jRecord on a disc with this unit after recording on it with other products.
jInsert an un-finalized disc in any other products.
∫ About format types
What is the DVD Video Recording format (VR
format)?
What is the DVD-Video format (Video
format)?
This is a format for recording on DVD discs
which allows you to record and erase repeatedly
and create playlists. You can record on DVD-
RAM and DVD-RW in DVD Video Recording
format with this unit.
By finalizing the disc, it can be played back on
most DVD players.
You can record on DVD-RW and DVD-R in DVD-
Video format with this unit.
≥ If a disc is recorded in VR format, the data can be exported on a computer.
∫ About DVD-R DL (Dual Layer)
DVD-R DL (Dual Layer) discs have two layers of recording/playback surface on one side.
If the first layer (L0) becomes full during recording, the recording continues uninterrupted on the second
layer (L1). However, the recorded picture is divided into 2 scenes at the point where the layers switch.
The unit automatically switches layers during disc playback so you can play the whole of the disc
continuously like a normal disc. However, the image or sound momentarily stop at the point where the
layers switch.
∫ Examples of discs that cannot be used on this unit
≥ Discs other than those with diameter of 8 cm
≥ Double layer discs other than DVD-R DL
≥ CD-RW
≥ CD-R
≥ iRW
≥ iR
≥ CD-ROM
≥ CD
≥ DVD-ROM
≥ DVD-Video
17
LSQT1161
Before using
When using brand-new DVD-RW
When using DVD-RW, select whether to record in DVD Video Recording format (VR format) or DVD-
Video format (Video format) and then format the disc. (l 17, About format types)
1 When a brand-new DVD-RW is inserted in this unit,
the screen on the right appears. Select [YES], then
press the joystick.
2 Select format type, then press the joystick.
[VIDEO]: DVD-Video format
[VR]:
DVD Video Recording format
3 When the confirm screen appears, select [YES],
then press the joystick.
≥ To change the format type, format the disc again. (l 74)
If the disc is formatted, then all the data recorded on the disc will be erased.
18
LSQT1161
Before using
Cards that you can use with this unit
Card type
Capacity
SD Memory Card
SDHC Memory Card
8 MB, 16 MB, 32 MB, 64 MB,
128 MB, 256 MB, 512 MB, 1 GB,
2 GB
4 GB
Indication in these
instructions
(SD)
This unit is compatible with both SD Memory cards and SDHC Memory cards. You can only use
SDHC Memory cards on devices that are compatible with them. You cannot use SDHC Memory
cards on devices that are only compatible with SD Memory cards. (When using an SDHC Memory
card on another device, be sure to read the operating instructions for that device.)
≥ For the purposes of these operating instructions, SD Memory Card and SDHC Memory Card are
referred to as the “SD card”.
≥ Motion pictures cannot be recorded on an SD card with this unit.
≥ Please confirm the latest information on the following website. (This website is in English only.)
http://panasonic.co.jp/pavc/global/cs/e_cam
≥ This unit supports SD Memory Cards formatted in FAT12 system and FAT16 system based on SD
Memory Card Specifications and SDHC Memory Cards formatted in FAT32 system.
≥ Use this unit to format SD cards. If an SD card is formatted on other products (such as a computer),
the time spent for recording may become longer and you may not be able to use the SD card. (l 75)
≥ We recommend that you use a Panasonic brand SD card.
≥ When the write-protect switch A on SD card is locked, no recording, deletion or
editing will be possible on the card.
A
≥ Keep the Memory Card out of reach of children to prevent swallowing.
≥ A MultiMediaCard cannot be used on this unit.
19
LSQT1161
Before using
Disc and card handling
∫ How to hold a disc or card
Do not touch the recording/playback surface or
the terminal surface.
∫ When inserting/removing a disc
Do not allow the recording/playback side of the disc to get fingerprints or dirty.
≥ If there is a scratch or dirt (e.g. dust or fingerprints) on the recording/playback side of the disc, images
cannot be recorded or played back normally and the following phenomena may occur:
jRecording or playback become impossible.
jPlayback image stops momentarily or sound is interrupted during playback.
jBlock noise appears on playback images.
jThe message “PLEASE CHECK FOR SCRATCHES OR STAINS ON DISC.” appears.
∫ If there is dirt on the disc
Clean it with the supplied disc cleaning cloth. Wipe the disc
from the centre to the outer edge to remove the dirt. Do not
use force when wiping the disc as it may scratch it. Also, do
not use solvents (thinner, water, antistatic agent, detergent
etc.)
∫ Handling precautions
≥ Be careful about scratches and dirt.
≥ Do not attach labels or stickers to discs.
(This may cause disc warping and un-balanced rotation, rendering it unusable.)
≥ Write on the label side of the disc only with a soft, oil-based felt pen. Do not use ballpoint pens or
other hard writing implements.
≥ Do not use record cleaning sprays, benzine, thinner, static electricity prevention liquids or any other
solvent.
≥ Do not use scratch-proof protectors or covers.
≥ Do not drop, stack, or impact discs. Do not place objects on them.
≥ Do not use the following discs:
jDiscs with exposed adhesive from removed stickers or labels.
jDiscs that are badly warped or cracked.
jIrregularly shaped discs, such as heart shapes.
≥ Do not expose the terminals of the card to water, garbage or dust.
≥ Do not place in the following areas:
jIn direct sunlight.
jIn very dusty or humid areas.
jNear a heater.
jLocations susceptible to significant difference in temperature (condensation can occur).
jWhere static electricity or electromagnetic waves occur.
≥ Put discs and cards back in their cases for protection when not using them.
20
LSQT1161
Setup
Setup
Power supply
Fitting the battery
Push the battery against the battery
holder and slide it until it clicks.
Charging the battery
When this unit is purchased, the battery is not
charged. Charge the battery before using this
unit.
≥ If the DC cable is connected to the AC
adaptor, then the battery will not charge.
Remove the DC cable from the AC adaptor.
A
Removing the battery
While sliding the BATTERY lever,
slide the battery to remove it.
1 Connect the AC cable to the AC
adaptor and the AC outlet.
2 Put the battery on the battery
mount by aligning the mark, and
then securely plug it in.
≥ The output plug of the AC cable is not
completely connected to the AC adaptor
socket. As shown in A, there is a gap.
≥ Hold the battery with your hand so it does not
fall.
∫ Charging lamp
Lights up: Charging
≥ Before removing the battery, be sure to set the
OFF/ON switch to OFF and check that the
status indicator is off.
Goes off: Charging completed
Flashing: The battery is over discharged
(discharged excessively). In a while,
the lamp will light up and normal
charging will start.
CAUTION
When the battery temperature is
excessively high or low, the
CHARGE lamp flashes and the
charging time will be longer than
normal.
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type recommended by the
manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
≥ Battery charging time (l 22)
≥ We recommend using Panasonic batteries.
(l 8)
≥ If you use other batteries, we cannot guarantee
the quality of this product.
21
LSQT1161
Setup
Charging time and recordable time
The times shown in the tables below are for when the temperature is 25 oC and the humidity is 60%. If
the temperature is higher or lower than 25 oC, the charging time will become longer.
∫ Charging time
≥ The charging time shown in the table are approximations.
≥ “2 h 25 min” indicates 2 hours 25 minutes.
VDR-D310:
Battery model number
Voltage/capacity
Charging time
Supplied battery/
CGA-DU12 (optional)
7.2 V/1150 mAh
2 h 25 min
CGA-DU14 (optional)
CGA-DU21 (optional)
7.2 V/1360 mAh
7.2 V/2040 mAh
2 h 45 min
3 h 55 min
VDR-D220:
Battery model number
Voltage/capacity
Charging time
Supplied battery/
CGR-DU06 (optional)
7.2 V/640 mAh
1 h 40 min
CGA-DU12 (optional)
CGA-DU14 (optional)
CGA-DU21 (optional)
7.2 V/1150 mAh
7.2 V/1360 mAh
7.2 V/2040 mAh
2 h 25 min
2 h 45 min
3 h 55 min
22
LSQT1161
Setup
∫ Recordable time (When using a DVD-RAM disc)
≥ The times indicate the recordable time when the viewfinder is used. The times in parentheses
indicate the recordable time when the LCD monitor is used.
≥ The actual recordable time refers to the recordable time on a disc when repeatedly starting/stopping
recording, turning the unit on/off, moving the zoom lever, etc.
≥ “1 h 25 min” indicates 1 hour 25 minutes.
VDR-D310:
Maximum
continuously
recordable time
Battery model
number
Voltage/
capacity
Recording
mode
Actual recordable
time
1 h 25 min
(1 h 20 min)
35 min
(35 min)
XP
SP
LP
XP
SP
LP
XP
SP
LP
Supplied
battery/
7.2 V/
1 h 40 min
(1 h 30 min)
45 min
(40 min)
CGA-DU12
(optional)
1150 mAh
1 h 45 min
(1 h 40 min)
45 min
(45 min)
1 h 45 min
(1 h 40 min)
45 min
(45 min)
CGA-DU14
(optional)
7.2 V/
1360 mAh
2 h
(1 h 50 min)
50 min
(50 min)
2 h 5 min
(1 h 55 min)
55 min
(50 min)
2 h 50 min
(2 h 40 min)
1 h 15 min
(1 h 10 min)
CGA-DU21
(optional)
7.2 V/
2040 mAh
3 h 10 min
(3 h)
1 h 25 min
(1 h 20 min)
3 h 20 min
(3 h 5 min)
1 h 30 min
(1 h 20 min)
VDR-D220:
Maximum
continuously
recordable time
Battery model
number
Voltage/
capacity
Recording
mode
Actual recordable
time
1 h 5 min
(1 h)
30 min
(25 min)
XP
SP
LP
XP
SP
LP
Supplied
battery/
CGR-DU06
(optional)
7.2 V/
640 mAh
1 h 20 min
(1 h 10 min)
35 min
(30 min)
1 h 25 min
(1 h 15 min)
35 min
(30 min)
2 h
(1 h 50 min)
55 min
(50 min)
CGA-DU12
(optional)
7.2 V/
1150 mAh
2 h 20 min
(2 h 10 min)
1 h
(55 min)
2 h 30 min
(2 h 15 min)
1 h 5 min
(1 h)
23
LSQT1161
Setup
Maximum
continuously
recordable time
Battery model
Voltage/
capacity
Recording
mode
Actual recordable
time
number
2 h 35 min
(2 h 20 min)
1 h 5 min
(1 h)
XP
SP
LP
XP
SP
LP
CGA-DU14
(optional)
7.2 V/
1360 mAh
3 h
(2 h 40 min)
1 h 20 min
(1 h 10 min)
3 h 10 min
(2 h 50 min)
1 h 25 min
(1 h 15 min)
3 h 50 min
(3 h 30 min)
1 h 40 min
(1 h 35 min)
CGA-DU21
(optional)
7.2 V/
2040 mAh
4 h 30 min
(4 h 5 min)
2 h
(1 h 50 min)
4 h 45 min
(4 h 20 min)
2 h 5 min
(1 h 55 min)
≥ The display changes as the battery capacity reduces.
#
#
#
#
.
If the battery discharges, then
(
) will flash.
≥ The recordable times will vary depending on the status of use. These times are approximations. The
recordable time will become shorter when you use both the viewfinder and the LCD monitor
simultaneously while rotating the LCD monitor frontward to record yourself, etc.
≥ The batteries heat up after use or charging. This unit will also heat up while being used. This is not a
malfunction.
≥ Be aware that the operating time of the battery will become shorter in low temperatures. We
recommend charging a spare battery for use when recording.
24
LSQT1161
Setup
How to turn on the power
Connecting to the AC outlet
The unit is in the standby condition when the AC
adaptor is connected. The primary circuit is
always “live” as long as the AC adaptor is
connected to an electrical outlet.
While pressing the button A, set the
OFF/ON switch to ON.
A
B
The status indicator B lights and the power turns
on.
≥ When the unit is turned on for the first time, a
message asking you to set the date and time
will appear. Select [YES] and set the date and
time. (l 35)
1 Connect the AC cable to the AC
adaptor and the AC outlet.
How to turn off the power
While pressing the button A, set the
OFF/ON switch to OFF.
2 Connect the DC cable to the AC
adaptor.
A
B
3 Connect the DC cable to this unit.
≥ Do not use the AC cable with any other
equipment as it is designed only for this unit.
Do not use the AC cable from other equipment
with this unit.
≥ While the DC cable is connected to the AC
adaptor, the battery will not charge.
The status indicator B goes off when the power
turns off.
Turning the unit on/off
≥ When recording, remove the lens cap before
turning the unit on.
If the unit is turned on with the lens cap
attached, the automatic white balance
adjustment (l 99) may not function properly.
25
LSQT1161
Setup
∫ To turn off the power
When the power is turned on for the first time
after changing the disc or battery, the unit
carries out a recognition procedure to check
that there are no problems with the disc.
This takes approximately 25 seconds with
DVD-RAM.
Close the LCD monitor and retract
the viewfinder.
If you want to start using the unit as soon as
you turn on the power, do the following.
1) Turn on the power.
2) After “READING DISC...” disappears from
the screen, turn off the power.
You can start recording approximately
8 seconds after you turn on the power again.
≥ Depending on the condition of the disc, it
may take longer than this.
≥ If the date and time are not set, it will take
longer than usual before you can start
recording.
The status indicator goes off and the power turns
off.
≥ The power will not turn off unless the LCD
monitor is closed and the viewfinder is
retracted.
≥ The power will not turn off while recording on a
disc even if the LCD monitor is closed and the
viewfinder is retracted.
Set the OFF/ON switch to OFF when the unit
is not being used.
How to turn the power on and off
with the LCD monitor/viewfinder
When the OFF/ON switch is set to ON, the power
can be turned on and off with the LCD monitor
and the viewfinder when the unit is in video
recording mode or picture recording mode.
Inserting/removing a disc
When inserting or removing the disc, fit the
charged battery pack or connect the AC adaptor
to the unit. The cover of the disc compartment
will not open unless the unit is powered.
∫ To turn on the power
Open the LCD monitor or extend the
viewfinder.
1 Fit the battery or connect the AC
adaptor.
2 Slide the DISC EJECT lever once
and release it.
The status indicator lights and the power turns
on.
26
LSQT1161
Setup
A few moments after the ACCESS/PC lamp
blinks, the cover of the disc compartment will
open slightly.
∫ Removing disc
While pressing down on the spindle, grasp the
edge of the disc and gently lift it out.
3 Open the cover of the disc
compartment by hand and insert/
remove the disc.
∫ Inserting disc
Fit the disc onto the spindle in the centre and
then push the disc down until it clicks into place.
A
B
Recording/playback side
Pickup lens
B
A
≥ Take care not to touch the recording/playback
sides of a disc when inserting or removing it.
4 Push the section marked
PUSH CLOSE on the cover of the
disc compartment to close the
cover.
≥ If you use a new DVD-RW, it is necessary to
format the disc. (l 18)
∫ Identifying recording/playback sides of
disc
Single sided disc:
The recording/playback side is opposite to the
labelled side.
Double sided disc:
The “SIDE A” recording/playback side is the side
opposite the side with the “SIDE A” mark. The
27
LSQT1161
Setup
“SIDE B” recording/playback side is the side with
the “SIDE A” mark.
touch the area around the pickup lens for it
becomes extremely hot.
A
After inserting a disc/After recording
finishes
While the ACCESS/PC lamp is lit, the disc is
rotating and disc information is being
recorded. If the power supply is interrupted at
this time, the disc may become unusable. Do
not disconnect the AC adaptor or remove the
battery. Also, do not strongly shake or cause
impact to the unit.
B
A
B
“SIDE A” mark
The opposite side is the “SIDE A” recording/
playback side.
≥ Do not use excessive force when opening the
cover.
≥ Do not touch the pickup lens or the recording/
playback side of the disc.
Inserting/removing an SD
card
Before inserting/removing an SD card, be
sure to set the OFF/ON switch to OFF.
This may impair recording and playback.
≥ Insert the disc securely to prevent damage.
≥ When you open the cover, the ACCESS/PC
lamp flashes red. Do not leave the cover open.
≥ If the cover is open, the power will not turn off
even if the OFF/ON switch is set to OFF.
≥ If the disc is not correctly inserted, the cover
will not close. Never try to forcibly close the
cover. This could cause damage. Reinsert the
disc properly.
If the SD card is inserted or removed while the
OFF/ON switch is set to ON, this unit may
malfunction or the data recorded on the SD
card may be lost.
≥ If a single sided disc is inserted into the unit
with the printed label facing the inside, an error
message will appear. Remove the disc and
reinsert it with its recording/playback side
facing the inside.
1 Set the OFF/ON switch to OFF to
turn off the power.
≥ Check that the status indicator has gone off.
≥ Do not allow the recording/playback side to
become dirty or scratched.
2 Slide the card slot cover to open.
≥ Do not remove the battery pack or disconnect
the AC adaptor while removing the disc or until
power is completely turned off. If you do, the
cover will not open. If this happens, reattach
the battery pack or reconnect the AC adaptor,
slide the DISC EJECT lever once, and then
release it. A repair disc message may be
displayed when the power is turned back on.
(l 89, About recovery)
≥ Do not insert anything other than the 8 cm
DVD-RAM, DVD-RW, DVD-R or DVD-R DL
disc into the disc compartment. Doing so could
cause malfunctions. (l 17, Examples of discs
that cannot be used on this unit)
≥ Do not touch the pickup lens or other parts
inside the disc compartment. Be sure not to
28
LSQT1161
Setup
3 Insert/remove the SD card into/
Selecting a mode
The mode dial is used to switch between
from the card slot.
recording and playback modes.
Rotate the mode dial slowly but surely.
Rotate the mode dial, and set the
desired mode pictograph to the
position shown in the illustration.
A
≥ When inserting an SD card, face the label side
A upwards and press it straight in as far as it
goes.
≥ When removing the SD card, press the centre
of the SD card and then pull it straight out.
4 Securely close the card slot
cover.
Video recording mode (l 39)
Use this to record motion pictures on a
disc.
∫ Concerning the SD card
≥ Electrical noise, static electricity or failure of
this unit or the SD card may damage or erase
the data stored on the SD card. We
recommend saving important data on a
computer.
Video playback mode (l 57)
Use this to play back motion pictures on
a disc.
Picture recording mode (l 42)
Use this to record still pictures on an
SD card.
∫ Card access lamp
Picture playback mode (l 61)
Use this to play back still pictures on an
SD card.
≥ Do not forcefully rotate the dial.
≥ When this unit accesses the SD card (reading,
recording, playback, erasing, etc.), the access
lamp lights up.
≥ If the following operations are performed when
the access lamp is lit, then the SD card or the
recorded data may be damaged or this unit
may malfunction.
How to use the joystick
This unit has a joystick for selecting functions,
performing operations, etc. so it is easy to
operate this unit with one hand.
sRemoving the SD card
sOperating the OFF/ON switch or the mode
dial
Basic operations
sRemoving the battery or disconnecting
the AC adaptor
Operations on the menu screen and selection of
files on the thumbnail view screen, etc.
29
LSQT1161
Setup
Move the joystick up, down, left, or
right to select an item or scene, and
then press the joystick to set it.
1 Move the joystick up, down, left
or right to select the scene to be
played back and press the
joystick.
1
5
3
4
2
1
2
3
4
5
Select by moving up.
Select by moving down.
Select by moving left.
Select by moving right.
Press the joystick to select the item.
≥ Menu screen operations (l 33)
The selected scene is played back on the full
screen.
The operation icon is automatically displayed on
the screen.
Operations during recording
¬Rotate the mode dial to select
or
2 Move the joystick up, down, left
.
or right to operate.
1 Press the centre of the joystick,
and icons will be displayed on
the screen.
≥ The operation icon appears or disappears
1/2NEXT
each time the centre of the joystick is pressed.
≥ The indication disappears when the centre of
the joystick is pressed again.
≥ The indication changes each time the joystick
is moved down.
2 Move the joystick up, left or right
to select an item.
Operations during playback
¬Rotate the mode dial to select
or
.
30
LSQT1161
Setup
About the operation icons displayed in each mode
About auto mode and manual mode (l 38)
Video recording mode
1/2NEXT
2/2NEXT
3/3NEXT
4/4NEXT
Icon
Direction
Function
Page
3
Backlight compensation
Fade
47
48
33
50
49
49
54
55
55
2
1
3
2
1
3
2
1
(1/2)
Help mode
Colour night view
Soft skin mode
Tele macro (VDR-D310)
White balance
Iris or gain value
Shutter speed
(2/2)
In manual mode
(3/3)
In manual focus
mode (4/4)
21
Manual focus adjustment
53
≥ The shaded operation icons are not displayed while recording.
Video playback mode
Icon
1/;
∫
Direction
Function
Page
57
3
4
Playback/pause
Stop playback and show thumbnails
57
:
6
2;
9
5
;1
Skip
57
2
1
Rewind
58
Reverse slow/frame playback (during pause)
58
Skip
57
Fast forward
58
Forward slow/frame playback (during pause)
58
31
LSQT1161
Setup
Picture recording mode
1/2NEXT
2/2NEXT
3/3NEXT
4/4NEXT
Icon
Direction
Function
Page
47
3
2
Backlight compensation
Self timer
50
(1/2)
Ø
1
2
1
3
2
1
Help mode
33
49
49
54
55
55
Soft skin mode
(2/2)
Tele macro (VDR-D310)
White balance
In manual mode
(3/3)
Iris or gain value
Shutter speed
In manual focus
mode (4/4)
21
Manual focus adjustment
53
Picture playback mode
Icon
1/;
∫
Direction
Function
Page
61
3
4
2
1
Slide show start/pause
Stop playback and show thumbnails
Playback previous picture (during pause)
Playback next picture (during pause)
61
E
61
D
61
32
LSQT1161
Setup
∫ Help mode
≥ When the help mode is used, functions cannot
be set.
≥ When the help mode is used, motion pictures
and still pictures cannot be recorded.
The help mode explains the operation icons that
are displayed when the AUTO/MANUAL/FOCUS
switch is set to AUTO in video/picture recording
mode.
¬Rotate the mode dial to select
or
.
Switching the language
You can switch the language on the screen
1 Press the joystick to display the
icon during the recording pause.
display or the menu screen.
1 Press the MENU button, then
select [LANGUAGE] and press
the joystick.
1/2NEXT
2 Move the joystick right to select
MENU
[
].
1/2NEXT
2 Select [English] and press the
joystick.
3 Move the joystick up, left or right
to select the desired icon.
Using the menu screen
Refer to “Menu list” (l 83) for information about
the menus.
EXIT
1/2NEXT
1 While stopped, press the MENU
button.
≥ An explanation of the selected icon is
displayed on the screen.
≥ The indication changes each time the joystick
is moved down.
MENU
To exit the help mode
Press the MENU button or select [EXIT].
The menu displayed differs depending on the
position of the mode dial.
EXIT
≥ Do not switch the mode dial when the menu is
displayed.
1/2NEXT
33
LSQT1161
Setup
2 Move the joystick up or down in
order to select the desired top
menu.
7 Press the joystick to enter the
selection.
To get back to the previous screen
Move the joystick left.
3 Move the joystick right or press
the joystick.
To exit the menu screen
Press the MENU button.
MENU
4 Move the joystick up or down in
order to select the submenu item.
≥ The menu screen does not appear during
recording or playing. You cannot start other
operations while the menu screen appears.
Operating with remote control
(VDR-D310)
The menu screen transition is the same as when
the buttons on the main unit are used.
5 Move the joystick right or press
the joystick.
1 Press the MENU button.
MENU
ENTER
6 Move the joystick up or down in
order to select the desired item.
2 Select a menu item.
MENU
ENTER
34
LSQT1161
Setup
≥ Use the direction buttons (3,4,2,1) and
ENTER button in place of the joystick on the
main unit.
move the joystick up or down to
set the desired value.
3 Press the MENU button to exit
the menu screen.
MENU
ENTER
≥ The year will change as follows:
2000, 2001, ..., 2099, 2000, ...
≥ The 24-hour system is used to display the time.
3 Press the joystick to enter the
selection.
≥ The clock function starts at [00] seconds when
the joystick is pressed.
≥ After pressing the MENU button to finish the
setting, check the date and time display.
Setting date and time
When the unit is turned on for the first time, a
message asking you to set the date and time will
appear.
≥ Select [YES] and press the joystick. Perform
steps 2 and 3 below to set the date and time.
∫ Changing the date and time display style
Press the MENU button, then select [SETUP]
# [DATE/TIME] # desired display style and
press the joystick.
≥ You can also show or change the date and
time display by repeatedly pressing the DATE/
TIME button on the remote control.
(VDR-D310)
If the screen shows the incorrect date and time,
then adjust it.
¬Rotate the mode dial to select
or
.
1 Press the MENU button, then
[DATE]
[D/T]
select [BASIC] # [CLOCK SET]
# [YES] and press the joystick.
15.12.2007 15:30
15.12.2007
[OFF]
MENU
∫ Changing the display style
Press the MENU button, then select [SETUP]
# [DATE FORMAT] # desired display style
and press the joystick.
2 Move the joystick left or right to
select the item to be set. Then,
Display style
[Y/M/D]
Screen display
2007.12.15
[M/D/Y]
12.15.2007
15.12.2007
[D/M/Y]
35
LSQT1161
Setup
2 Move the joystick up or down to
select the item to be adjusted.
Then, move the joystick left or
right to make the adjustment.
≥ The date and time function are driven by a
built-in lithium battery.
≥ Make sure to check the time before recording.
≥ If the time display becomes [- -], the built-in
lithium battery has run down. Use the following
steps to charge the battery. When you turn on
the power for the first time after charging, a
message asking you to set the date and time
will appear. Select [YES] and set the date and
time.
To recharge the built-in lithium battery
Connect the AC adaptor or attach the battery
to the unit, and the built-in lithium battery will
be recharged. Leave the unit as it is for approx.
24 hours and the battery will save the date and
time for approx. 6 months. (Even if the OFF/
ON switch is set to OFF, the battery is still
being recharged.)
The bar display moves.
∫ [LCD SET]
[BRIGHTNESS]:
Brightness of the LCD monitor
[COLOUR]:
Colour level of the LCD monitor
∫ [EVF SET]
[BRIGHTNESS]:
WARNING
Brightness of the viewfinder
THE LITHIUM BATTERY IN THIS UNIT MUST
ONLY BE REPLACED BY QUALIFIED
PERSONNEL. IF THIS IS NECESSARY,
CONTACT THE PANASONIC CUSTOMER
CARE CENTRE ON 132600 FOR YOUR
NEAREST AUTHORIZED SERVICE CENTRE.
≥ To adjust the brightness of the viewfinder,
extend the viewfinder and close the LCD
monitor to activate the viewfinder.
≥ When the LCD monitor is rotated by 180°
towards the lens, the brightness and colour
level of the LCD monitor cannot be adjusted.
≥ These settings will not affect the images
actually recorded.
Adjusting LCD monitor/
viewfinder
Adjusting the field of view
Adjust the focus by sliding the
eyepiece corrector knob.
Adjusting the brightness and
colour level
1 Press the MENU button, then
select [SETUP] # [LCD SET] or
[EVF SET] # [YES] and press the
joystick.
0h00m00s
0h00m00s
MENU
36
LSQT1161
Recording
Recording
Before recording
Basic camera positioning
1
4
3
2
5
1
2
3
4
5
Hold the camera with both hands.
Put your hand through the grip belt.
Do not cover the microphones or sensors with your hands.
Keep your arms near your body.
Slightly open your legs.
≥ When you are outdoors, record pictures with the sunlight behind you. If the subject is backlit, it will
become dark in the recording.
≥ When recording, make sure your footing is stable and there is no danger of colliding with another
person, a ball etc.
37
LSQT1161
Recording
∫ About auto mode
Set the AUTO/MANUAL/FOCUS switch to AUTO,
and colour balance (white balance) and focusing will
be adjusted automatically.
jAuto white balance (l 99)
jAuto focusing (l 100)
Depending on the brightness of the subject etc., the
aperture and shutter speed are automatically
adjusted for an optimum brightness.
(When set to the video recording mode: The shutter
speed is adjusted to a maximum of 1/250.)
≥ Colour balance and focus may not be adjusted automatically depending on light sources or scenes. If
so, manually adjust these settings.
jScene mode (l 52)
jWhite balance (l 54)
jShutter speed (l 55)
jIris/gain value (l 55)
jFocus (l 53)
∫ Anti-Ground-Shooting (AGS) (VDR-D310)
This function prevents unnecessary recording when you forget to pause
recording and walk with the unit tilted upside down while recording continues.
≥ If the unit continues to be tilted upside down from the normal horizontal position
while recording on a disc, it is automatically set to recording pause.
¬Rotate the mode dial to select
.
Press the MENU button, then select [SETUP] # [AGS] #
[ON] and press the joystick.
≥ The AGS function may activate and cause the unit to pause the recording if you are recording a
subject right above or right below you. In these cases, set [AGS] to [OFF] then continue the
recording.
≥ Use the recording start/stop button to pause the recording. The AGS function is only a backup
function for when you forget to pause the recording.
≥ The time it takes the unit to be put into recording pause after being tilted upside down varies
depending on the operating conditions.
38
LSQT1161
Recording
Recording motion pictures
(RAM) (-RW‹VR›) (-RW‹V›) (-R)
Record motion pictures onto a disc.
≥ When the unit is purchased, the aspect ratio is set to [16:9] for recording images compatible with a
wide-screen TV.
To watch images on a regular TV (4:3), change the aspect ratio setting (l 51) before recording the
images or when watching them on the connected TV (l 77).
≥ Remove the lens cap before turning the unit on.
If the unit is turned on with the lens cap attached, the automatic white balance adjustment may not
function properly.
1 Turn the unit on.
2 Rotate the mode dial to select
.
3 Open the LCD monitor or extend the viewfinder.
4 Press the recording start/stop
button to start recording.
To end the recording
Press the recording start/stop button again to pause
recording.
≥ [¥] and [;] are red during recording. Do not move
this unit until [;] is green.
≥ The images recorded between pressing the recording start/stop button to start recording and
pressing it again to pause recording become one scene.
39
LSQT1161
Recording
≥ When about 5 minutes have passed without any operation in recording pause, the unit automatically
turns off to prevent the battery from running down. When you want to use the unit, turn it on again.
This setting can also be set to [OFF]. (l 84, [POWER SAVE])
Screen indications in the video recording mode
A
B
Recording mode
A
SP
30min
0h00m10s
Remaining time left for recording
(When the remaining time is less than 1 minute, [R 0min]
flashes red.)
R
B
C
C
Recording time elapsed
≥ The maximum number of scenes on a disc (per side): 999 (Even if there is remaining capacity for
recording on a disc, you may not be able to record 999 scenes.)
≥ Maximum number of dates on a disc (per side): 99 (Even if scenes are recorded on the same day,
they may be grouped on a different recording date.) (l 60)
≥ Sound is recorded in Dolby Digital from the internal stereo microphone on the front of the unit. Take
care not to block this microphone.
≥ Each time the unit enters the recording pause mode, the counter display will be reset to “0h00m00s”.
≥ While motion picture recording is in progress, the recording will not stop even if the LCD monitor is
closed and the viewfinder is retracted.
≥ While “WRITING CONTROL DATA TO DISC. DO NOT SHAKE THE UNIT.” is displayed, do not
disconnect the AC adaptor or remove the battery as doing so may make the disc unusable.
≥ While motion picture recording is in progress, do not disconnect the AC adaptor or remove the
battery. If you do, a repair disc message may be displayed when the power is turned back on. (l 89,
About recovery)
The ACCESS/PC lamp lights immediately after recording finishes. While it lights, the disc is rotating
and disc information is being recorded. If you run while holding the unit or swing it, the recorded
images may be distorted so do not strongly shake or cause impact to it.
Recording modes and recordable time available for the
motion picture
Changing the recording mode of the motion picture.
Press the MENU button, then select
[BASIC] # [REC MODE] # desired
item and press the joystick.
MENU
40
LSQT1161
Recording
∫ Approximate recordable time for 1 disc (single sided)
Recording mode
Disc type
XP
SP
LP
(High quality)
(Normal)
(Long play)
Approx. 75 min
Approx. 138 min
DVD-RAM
DVD-R DL
Approx. 18 min
Approx. 35 min
Approx. 37 min
Approx. 69 min
Image quality
prioritized
Recording time
prioritized
≥ This unit records in VBR. VBR is an abbreviation for Variable Bit Rate. VBR recording automatically
varies the bit rate (amount of data in a fixed time) depending on the subject being recorded. This
means if a subject with sharp movements is recorded, the recording time is reduced.
≥ Mosaic-pattern noise may appear on a playback image in the following cases.
jWhen there is a complicated pattern in the background
jWhen the unit is moved too much or too fast
jWhen a subject with sharp movements has been recorded
(Particularly if it has been recorded in [LP] mode.)
41
LSQT1161
Recording
Recording still pictures (JPEG still pictures)
(SD)
Record the still picture on an SD card.
2
≥ When this unit is purchased, [PICTURE SIZE] is set to [
recording pictures compatible with a wide-screen TV (16:9).
] (VDR-D310)/[ 0.2 ] (VDR-D220) for
To record pictures with a 4:3 aspect ratio, change the [PICTURE SIZE] setting before recording
(l 45).
≥ Remove the lens cap before turning the unit on.
If the unit is turned on with the lens cap attached, the automatic white balance adjustment may not
function properly.
1 Turn the unit on.
2 Rotate the mode dial to select
.
3 Open the LCD monitor or extend the viewfinder.
∫ VDR-D310
4 Press the
button halfway in order
to adjust focusing. (For auto
focusing only)
The shutter speed and the iris/gain value are fixed
and the unit focuses on the subject automatically.
≥ If [O.I.S.] (l 51) is set to [ON], the image stabilizer
function will become more effective when the
button is pressed halfway. ([
] (MEGA optical
MEGA
image stabilizer) will be displayed.)
42
LSQT1161
Recording
A
Shutter chance mark
± (The white lamp flashes.):
¥ (The green lamp lights up.): When in focus
A
B
Focusing
No mark:
When focusing is unsuccessful.
≥ The shutter chance mark is indicated as follows when the
is not pressed halfway. Please use it as a guide for recording.
button
¥ (The green lamp lights up.): When in focus and a good picture can be recorded.
± (The white lamp lights up.): Almost in focus
Focus area
B
5 Press the
button fully to take the
picture.
∫ VDR-D220
4 Press the
button.
The unit automatically focuses on the subject at the
centre of screen (when auto focus is selected).
≥ For information about the number of recordable still pictures on an SD card (l 103)
≥ The sound cannot be recorded.
≥ If the write protection switch on the SD card is set to LOCK, it cannot be used for recording.
≥ The button on the remote control cannot be pressed halfway. (VDR-D310)
≥ If the [PICT.QUALITY] is set to [
], mosaic-pattern noise may appear on a playback image
depending on the picture content.
≥ While this unit accesses the SD card (
is displayed/the access lamp is lit), do not perform the
following operations. The SD card or the recorded data may be damaged.
jTurn the unit off.
jRemove the SD card.
jOperate the mode dial.
≥ Other products may degrade or not play back still pictures recorded on this unit.
∫ To record still pictures clearly
≥ When zooming in on the subject with a magnification of 4k or higher, it is difficult to reduce the slight
shaking from holding this unit by hand. We recommend decreasing the zoom magnification and
approaching the subject when recording.
43
LSQT1161
Recording
≥ When recording still pictures, hold the unit firmly with your hands and keep your arms stationary at
your side so as not to shake the unit.
≥ You can record stable pictures without shaking by using a tripod and the remote control.
Screen indications in picture recording mode
A
Remaining number of still pictures
(Flashes in red when [R 0] appears.)
Size of still pictures
A
B
C
R 100
B
C
Quality of still pictures
∫ About the shutter chance mark (VDR-D310)
≥ The shutter chance mark does not appear in manual focus mode.
≥ Focus on a subject manually when it is not easily focused.
≥ You can record still pictures on the card even if the shutter chance mark does not appear, but pictures
may be recorded without being focused.
≥ The shutter chance mark does not appear or has difficulty displaying in the following cases.
jWhen the zoom magnification is high.
jWhen the unit is shaken.
jWhen the subject is moving.
jWhen the subject stands in front of a light source.
jWhen close subjects and far subjects are included in the same scene.
jWhen the scene is dark.
jWhen there is a bright part in the scene.
jWhen the scene is filled with only horizontal lines.
jWhen the scene lacks contrast.
∫ Concerning the focusing area (VDR-D310)
When there is a contrasting object ahead or behind the subject in the focus area, the subject may not
be focused. If so, move the contrasting object out of the focus area.
Even when it is still difficult to focus, adjust the focus manually.
Recording with a shutter operation effect
You can add a shutter sound when recording still pictures.
Press the MENU button, then select
[ADVANCED] # [SHTR EFFECT] #
[ON] and press the joystick.
MENU
≥ This function’s default setting is [ON].
44
LSQT1161
Recording
Number of pixels and picture quality for still picture recording
∫ [PICTURE SIZE]
Changing the recording size.
Press the MENU button, then select
[BASIC] # [PICTURE SIZE] # desired
item and press the joystick.
MENU
VDR-D310:
Icon
Aspect
4:3
Number of pixels
2048k1512
1280k960
3.1M
1
M
4:3
0.3M
4:3
640k480
2
16:9
1920k1080
VDR-D220:
Icon
0.3M
Aspect
4:3
Number of pixels
640k480
0.2
16:9
640k360
2
≥ When this unit is purchased, [PICTURE SIZE] is set to [
] (VDR-D310)/[ 0.2 ] (VDR-D220). The
sides of pictures recorded with a 16:9 aspect ratio may be cut at printing. Check before printing.
∫ [PICT.QUALITY]
Selecting the picture quality.
Press the MENU button, then select [BASIC] # [PICT.QUALITY] # desired
item and press the joystick.
:Still pictures with a high picture quality are recorded.
: Priority is given to the number of still pictures recorded. Still pictures are recorded in normal picture
quality.
45
LSQT1161
Recording
≥ The zoom speed varies depending on the
range over which the zoom lever is moved.
(The zoom speed does not vary when
operating with the remote control.)
Various recording
functions
≥ When the zoom speed is high, the subject may
not be focused easily.
≥ If you take your finger off the zoom lever during
zoom operation, the operation sound may be
recorded. When returning the zoom lever to
the original position, move it quietly.
Zoom in/out function
(RAM) (-RW‹VR›) (-RW‹V›) (-R) (SD)
VDR-D310:
You can zoom in up to 10k optically.
VDR-D220:
You can zoom in up to 32k optically.
Digital zoom function
(RAM) (-RW‹VR›) (-RW‹V›) (-R)
¬Rotate the mode dial to select
or
.
If the zoom magnification exceeds 10k
(VDR-D310)/32k (VDR-D220), then the digital
zoom function will be activated. The maximum
magnification provided by the digital zoom can
be switched.
Move the zoom lever.
¬Rotate the mode dial to select
.
Press the MENU button, then select
[ADVANCED] # [D.ZOOM] #
desired item and press the joystick.
T side: Close-up recording (zoom in)
W side: Wide-angle recording (zoom out)
MENU
VDR-D310:
[OFF]: Optical zoom only (Up to 10k)
[25k]: Up to 25k
[700k]: Up to 700k
≥ If [25k] or [700k] is selected, the digital zoom
range is displayed in blue while zooming.
≥ When zooming in while holding this unit by
hand, we recommend using the image
stabilizer function. (l 51)
≥ When distant subjects are brought closer, they
are focused at about 1 m (VDR-D310)/1.3 m
(VDR-D220) or more.
≥ When the zoom magnification is 1k, this unit
can focus on a subject approx. 3.5 cm
(VDR-D310)/2 cm (VDR-D220) away from the
lens. (Macro function)
VDR-D220:
[OFF]: Optical zoom only (Up to 32k)
[50k]: Up to 50k
[1000k]: Up to 1000k
≥ If [50k] or [1000k] is selected, the digital zoom
range is displayed in blue while zooming.
≥ The larger the digital zoom magnification, the
more the image quality is degraded.
46
LSQT1161
Recording
≥ This function cannot be used in picture
recording mode.
The image is horizontally flipped as if you see a
mirror image. (However the image recorded is
the same as a normal recording.)
≥ Extend the viewfinder to see the picture while
recording.
≥ When the recording aspect is 16:9, the image
displayed on the viewfinder screen is
squeezed horizontally, but this is normal and
not a sign of any trouble.
To use the zoom microphone
function
(RAM) (-RW‹VR›) (-RW‹V›) (-R)
The zoom microphone is linked to the zooming
operation so that far-away sounds with a tele-
shot and close-up sounds with a wide-angle shot
are recorded more clearly.
≥ When the LCD monitor is rotated towards the
lens side, the icon will not be displayed even if
you press the joystick.
¬Rotate the mode dial to select
.
≥ Only some indications will appear on the
screen. When [°] appears, return the
direction of the LCD monitor to normal position
and check the warning/alarm indication. (l 88)
Press the MENU button, then select
[ADVANCED] # [ZOOM MIC] # [ON]
and press the joystick.
Backlight compensation
function
MENU
This is for protecting a backlit subject
from being darkened.
(RAM) (-RW‹VR›) (-RW‹V›) (-R) (SD)
Use this function when the light is emanating
from behind the subject and the subject appears
dark.
≥ The zoom microphone function does not work
with an external microphone. (VDR-D310)
¬Rotate the mode dial to select
or
Recording yourself
.
1 Press the joystick. Then move
the joystick down to display the
icon shown in the illustration.
(RAM) (-RW‹VR›) (-RW‹V›) (-R) (SD)
You can record yourself while viewing the LCD
monitor. You can record persons in front of the
unit while showing them the image.
¬Rotate the mode dial to select
or
.
Rotate the LCD monitor towards the
lens side.
1/2NEXT
47
LSQT1161
Recording
2 Move the joystick up to select
3 Press the recording start/stop
button.
[ª].
Start recording. (Fade in)
1/2NEXT
The image on the screen will become brighter.
To return to normal recording
Select [ª] again.
When you start recording, the image/audio
gradually appears.
≥ If you turn off the power or operate the mode
dial, the backlight compensation function is
cancelled.
Pause recording. (Fade out)
Fade in/fade out function
(RAM) (-RW‹VR›) (-RW‹V›) (-R)
Fade in: The image and audio gradually
appear.
Fade out: The image and audio gradually
disappear.
The image/audio gradually disappears. After the
image/audio completely disappears, recording
stops.
¬Rotate the mode dial to select
.
1 Press the joystick. Then move
the joystick down to display the
icon shown in the illustration.
≥ After recording, the fade setting is cancelled.
To cancel fading
Select [
] again.
To select the colour for fade in/out
The colour which appears in fading pictures can
be selected.
1/2NEXT
Press the MENU button, then select
[ADVANCED] # [FADE COLOUR] # [WHITE]
or [BLACK] and press the joystick.
2 Move the joystick left to select
[
].
≥ If you turn off the power, the fade function is
cancelled.
≥ While the fade in/fade out function is selected,
it takes several seconds to display the image
when you start recording. It also takes several
seconds to pause recording.
1/2NEXT
≥ The thumbnails of scenes recorded using fade
in become black (or white).
48
LSQT1161
Recording
Soft skin mode
Tele macro function
(VDR-D310)
This is for bringing only what you
want to record into focus to take
close-ups.
This makes skin colours appear softer
for a more attractive appearance.
(RAM) (-RW‹VR›) (-RW‹V›) (-R) (SD)
This is more effective if you record the bust
image of a person.
(RAM) (-RW‹VR›) (-RW‹V›) (-R) (SD)
By focusing only on the subject and blurring the
background, the image can be impressive.
The unit can focus on the subject at a distance of
approx. 50 cm.
¬Rotate the mode dial to select
or
.
1 Press the joystick. Then move
the joystick down to display the
icon shown in the illustration.
¬Rotate the mode dial to select
or
.
1 Press the joystick. Then move
the joystick down to display the
icon shown in the illustration.
2/2NEXT
2 Move the joystick left to select
2/2NEXT
[
].
2 Move the joystick right to select
[
].
2/2NEXT
To cancel the soft skin mode
Select [
] again.
2/2NEXT
≥ If the background or anything else in the scene
has colours similar to the skin colour, they will
also be smoothed.
≥ If the magnification is 10k or less, then it is
automatically set to 10k.
≥ If the brightness is insufficient, the effect may
not be clear.
≥ You may not be able to see the face clearly
when recording a distant person. In this case,
cancel soft skin mode or zoom in on the face.
To cancel the tele macro function
Select [
] again.
≥ If a sharper focus cannot be achieved, adjust
the focus manually. (l 53)
49
LSQT1161
Recording
≥ In the following cases, the tele macro function
≥ The colour night view function makes the
signal charging time of CCD up to
is cancelled.
jThe zoom magnification becomes lower than
approximately 25k longer than usual, so that
dark scenes can be recorded brightly. For this
reason, bright dots that are usually invisible
may be seen, but this is not a malfunction.
≥ If you turn off the power or operate the mode
dial, the colour night view function is cancelled.
≥ If set in a bright place, the screen may become
whitish for a while.
10k.
jThe power is turned off or the mode dial is
operated.
Colour night view function
This allows recording in dark
locations.
(RAM) (-RW‹VR›) (-RW‹V›) (-R)
Self-timer recording
This is for recording shots of yourself
as well.
This function allows you to record colour subjects
in dark locations to stand out against the
background.
Attach this unit to a tripod, and you can record
images free from vibration.
(SD)
You can record still pictures on an SD card using
the timer.
≥ Minimum required illumination: approx. 1 lx
(VDR-D310)/approx. 2 lx (VDR-D220)
≥ Recorded scene is seen as if frames were
missed.
¬Rotate the mode dial to select
.
1 Press the joystick. Then move
the joystick down to display the
icon shown in the illustration.
¬Rotate the mode dial to select
.
1 Press the joystick. Then move
the joystick down to display the
icon shown in the illustration.
1/2NEXT
2/2NEXT
2 Move the joystick left to select
[Ø].
2 Move the joystick up to select
[
].
1/2NEXT
2/2NEXT
3 Press the
button.
≥ If it is difficult to focus, adjust the focus
manually. (l 53)
After the [Ø] display flashes for approx.
10 seconds, a still picture will be recorded.
≥ After recording, the self-timer is cancelled.
To cancel the colour night view function
Select [
] again.
50
LSQT1161
Recording
≥ If you press the
button halfway and then
fully, the subject is focused when the button is
pressed halfway. (VDR-D310)
Wide mode
This is for selecting the screen’s
aspect ratio when recording motion
pictures.
≥ When you press the
button fully in auto
focus mode, the subject is focused just before
recording. (VDR-D310)
(RAM) (-RW‹VR›) (-RW‹V›) (-R)
To stop the timer midway through
Press the MENU button. (The self-timer setting is
cancelled.)
This allows you to record images compatible with
wide-screen TVs (16:9) and regular TVs (4:3).
≥ If you turn off the power, the self-timer standby
mode is cancelled.
≥ Depending on the time taken to bring the
subject into focus, the recording may take
longer than set to start.
∫ Recording images with a 16:9
aspect ratio
¬Rotate the mode dial to select
.
Press the MENU button, then select
[BASIC] > [REC ASPECT] > [16:9]
and press the joystick.
Recording guideline
function
Checking if the image is level.
MENU
(RAM) (-RW‹VR›) (-RW‹V›) (-R) (SD)
You can check if the image is level while
recording by using the lines displayed on the
screen.
∫ Recording images with a 4:3
¬Rotate the mode dial to select
or
.
aspect ratio
Press the MENU button, then select
[BASIC] # [GUIDE LINES] # [ON]
and press the joystick.
¬Rotate the mode dial to select
.
Press the MENU button, then select
[BASIC] > [REC ASPECT] > [4:3]
and press the joystick.
≥ The default setting is [16:9].
MENU
Image stabilizer function
This is for reducing image shakes
during recording.
To cancel the Recording guideline
function
Press the MENU button, then select [BASIC] #
[GUIDE LINES] # [OFF] and press the joystick.
(RAM) (-RW‹VR›) (-RW‹V›) (-R) (SD)
Reduces the image shaking due to hand
movement when recording.
¬Rotate the mode dial to select
or
≥ The guidelines do not appear on the images
actually recorded.
.
≥ The guidelines are not displayed while rotating
the LCD monitor frontward to record yourself.
51
LSQT1161
Recording
Press the MENU button, then select
[ADVANCED] # [O.I.S.] # [ON] and
press the joystick.
Press the MENU button, then select
[ADVANCED] # [WIND CUT] # [ON]
and press the joystick.
MENU
MENU
To cancel the image stabilizer function
Press the MENU button, then select
[ADVANCED] # [O.I.S.] # [OFF] and press the
joystick.
To cancel the wind noise reduction
function
Press the MENU button, then select
[ADVANCED] # [WIND CUT] # [OFF] and
press the joystick.
≥ This function’s default setting is [ON].
≥ In the picture recording mode, pressing the
button halfway increases the effect of the
image stabilizer function. (MEGA optical image
stabilizer) (VDR-D310)
≥ In the following cases, the image stabilizer
function may not work effectively.
jWhen the digital zoom is used
≥ This function’s default setting is [ON].
≥ The wind noise reduction depends on the wind
strength. (If this function is activated in strong
winds, the stereo effect may be reduced. When
the wind weakens, the stereo effect will be
restored.)
≥ The wind noise reduction function does not
work with an external microphone.
(VDR-D310)
jWhen the unit is shaken greatly
jWhen you record a moving subject while
tracking it
Wind noise reduction
function
This is for reducing the wind noise
coming into the microphone when
recording.
Manual recording
functions
Scene mode
This is for recording in various
situations.
(RAM) (-RW‹VR›) (-RW‹V›) (-R)
¬Rotate the mode dial to select
.
(RAM) (-RW‹VR›) (-RW‹V›) (-R) (SD)
When you record images in different situations,
this mode automatically sets optimum shutter
speeds and apertures.
¬Rotate the mode dial to select
or
.
52
LSQT1161
Recording
≥ Avoid recording under fluorescent light,
1 Set the AUTO/MANUAL/FOCUS
mercury light or sodium light because the
colour and brightness of the playback image
may change.
switch to MANUAL.
≥ If you record a subject illuminated with strong
light or a highly reflective subject, vertical lines
of light may appear.
≥ If the brightness is insufficient, the sports mode
does not function. The [5] display flashes.
≥ If this mode is used indoors, the screen may
flicker.
2 Press the MENU button, then
select [BASIC] # [SCENE MODE]
# desired item and press the
joystick.
Portrait mode
≥ If this mode is used indoors, the screen may
flicker. If so, change the scene mode setting to
[OFF].
Low light mode
≥ Extremely dark scenes may not be able to be
recorded finely.
Spotlight mode
MENU
≥ If the recording subject is extremely bright, the
recorded image may become whitish and the
periphery of the recorded image extremely
dark.
Surf & snow mode
[5] Sports
≥ If the subject is extremely bright, the recorded
image may become whitish.
To record sports scenes or scenes where there
are quick motions
[
] Portrait
To make people stand out against the
background
Manual focus adjustment
[
] Low light
To make the scene brighter in dark conditions
] Spotlight
(RAM) (-RW‹VR›) (-RW‹V›) (-R) (SD)
If auto focusing is difficult due to the conditions,
then manual focusing is available.
[
To make the subject under a spotlight look more
attractive
[
¬Rotate the mode dial to select
or
] Surf & snow
.
To record images in bright places such as ski
slopes and beaches
1 Set the AUTO/MANUAL/FOCUS
switch to MANUAL.
To cancel the scene mode function
Press the MENU button, then select [BASIC] #
[SCENE MODE] # [OFF] and press the joystick.
≥ You can also cancel the scene mode function
by setting the AUTO/MANUAL/FOCUS switch
to AUTO.
Sports mode
≥ For slow-motion playback or playback pause of
recorded pictures, this mode helps diminish
camera shake.
≥ During normal playback, the image movement
may not look smooth.
53
LSQT1161
Recording
2 Move the switch down and set it
1 Set the AUTO/MANUAL/FOCUS
to FOCUS position.
switch to MANUAL.
MNL
MNL
4/4NEXT
3/3NEXT
The manual focus indication [MF] and the icon
shown in the illustration appear.
The icon shown in the illustration is displayed
automatically.
3 Move the joystick left or right to
2 Move the joystick up to select
bring the subject into focus.
[
].
MNL
MNL
4/4NEXT
3/3NEXT
≥ The subject may not be in focus when zoomed
in if focusing with a wide angle. First, zoom in
on the subject, and then focus on it.
3 Move the joystick left or right to
select the white balance mode.
MNL
BACK
To restore to the automatic adjustment
Press the AUTO/MANUAL/FOCUS switch down
again to the FOCUS position.
≥ You can also restore the auto focusing by
setting the AUTO/MANUAL/FOCUS switch to
AUTO.
[
[
] Auto white balance adjustment
AWB
]
Indoor mode (for recording under
incandescent lamps)
≥ Incandescent lights, halogen lamps
[
[
]
]
Outdoor mode
≥ Outdoors under a clear sky
White balance
This is for recording in natural
colours.
Manual adjustment mode
≥ Mercury-vapor lamps, sodium lamps,
some fluorescent lights
≥ Lights used for wedding receptions at
hotels, stage spotlights in theatres
≥ Sunrise, sunset, etc.
(RAM) (-RW‹VR›) (-RW‹V›) (-R) (SD)
The automatic white balance function may not
reproduce natural colours depending on the
scenes or lighting conditions. If so, you can
adjust the white balance manually.
To restore to the automatic adjustment
Set the white balance mode to [
].
AWB
¬Rotate the mode dial to select
or
≥ You can also restore the automatic adjustment
by setting the AUTO/MANUAL/FOCUS switch
to AUTO.
.
54
LSQT1161
Recording
will temporarily be black. (The black balance
cannot be adjusted manually.)
To set the white balance manually
1
2
3
1 Select [ ], fill the screen with a
white subject.
1
2
3
Black balance adjustment in progress.
(Flashes.)
White balance adjustment in progress.
(Flashes.)
MNL
BACK
Adjustment completed. (Lights up.)
≥ When the unit is turned on with the lens cap
attached, the automatic white balance
adjustment may not function properly. Please
turn the unit on after removing the lens cap.
2 Move the joystick up to select
[
].
≥ When the [
] display flashes, the manual
MNL
white balance previously adjusted is stored.
Whenever recording conditions change, re-set
the white balance for correct adjustment.
≥ When setting both the white balance and the
iris/gain, set the white balance first.
BACK
When the [
] display changes from flashing to
on, setting is complete.
Manual shutter speed/
aperture adjustment
≥ When the [
] display continues flashing, the
white balance cannot be set because the place
is dark etc. In this case, use the automatic
white balance.
(RAM) (-RW‹VR›) (-RW‹V›) (-R) (SD)
Shutter Speed:
Adjust it when recording fast-moving subjects.
∫ About the white balance sensor A
Aperture:
Adjust it when the screen is too bright or too
dark.
¬Rotate the mode dial to select
or
.
A
1 Set the AUTO/MANUAL/FOCUS
switch to MANUAL.
The white balance sensor detects the type of
light source during recording.
MNL
Do not cover the white balance sensor during
recording, or it may not function properly.
∫ About the black balance
3/3NEXT
adjustment (VDR-D310)
The icon shown in the illustration is displayed
automatically.
This is one of the 3CCD system functions that
automatically adjusts the black when the white
balance is set in the manual adjustment mode.
When the black balance is adjusted, the screen
55
LSQT1161
Recording
≥ You may see vertical lines of light in the
playback image of a brightly shining subject or
highly reflective subject, but this is not a
malfunction.
2 Move the joystick left or right to
select [ ] (aperture) or [
(shutter speed).
]
≥ During normal playback, image movement
may not look smooth.
MNL
≥ When recording in an extremely bright place,
the screen may change colour or flicker. If so
adjust the shutter speed manually to [1/50] or
[1/100].
3/3NEXT
∫ Manual iris/gain adjustment
3 Move the joystick left or right to
≥ If the gain value is increased, the noise on the
screen increases.
make the adjustment.
≥ Depending on the zoom magnification, there
are iris values that are not displayed.
MNL
A
1/100
OPEN
B
BACK
A
B
Shutter speed:
1/50 to 1/8000
1/25 to 1/2000 (VDR-D310)
1/50 to 1/500 (VDR-D220)
≥ The shutter speed closer to 1/8000 is
faster.
Iris/Gain value:
CLOSE # (F16 to F2.0) # OPEN #
(0dB to 18dB)
≥ Value closer to [CLOSE] darken the image.
≥ Value closer to [18dB] brighten the image.
≥ When the iris value is adjusted to brighter
than [OPEN], it changes to the gain value.
To restore to automatic adjustment
Set the AUTO/MANUAL/FOCUS switch to
AUTO.
≥ When setting both the shutter speed and the
iris/gain value, set the shutter speed and then
set the iris/gain value.
∫ Manual shutter speed adjustment
≥ Avoid recording under fluorescent light,
mercury light or sodium light because the
colour and brightness of the playback image
may change.
≥ If you increase the shutter speed manually, the
gain value will increase automatically
depending on how much the sensitivity lowers
and the noise on the screen may increase.
56
LSQT1161
Playback
Playback
Motion picture playback
(RAM) (-RW‹VR›) (-RW‹V›) (-R)
Play back the motion pictures recorded on the disc.
1 Rotate the mode dial to select
The motion pictures recorded on the disc are
displayed as thumbnails.
.
2 Select the scene to be played back.
A
B
Scene number
Scroll bar display
A
The selected scene will be encircled by a yellow frame.
≥ When 9 or more scenes have been recorded, the next (or previous)
page is displayed by moving the joystick.
≥ If you move and hold the joystick up or down, you can advance
8 scenes at a time. The screen will not change at this time, but the
scene numbers and scroll bar display will change so release the
joystick when you have arrived at the page with the scene you want to
display.
B
3 Press the joystick.
The selected scene is played back on the full screen.
The operation icon is automatically displayed on the screen.
4 Move the joystick to operate.
1/;: Playback/Pause
:: Skip playback (backward)
9: Skip playback (forward)
∫:
Stops the playback and shows the thumbnails
57
LSQT1161
Playback
≥ No sound will be heard except during normal playback.
≥ If pause play is continued for 5 minutes, the screen returns to the thumbnails.
≥ When the amount of time recorded on the scene is short, playback may not be possible.
≥ When a scene is displayed as [
] on the thumbnail display, playback is not possible.
≥ The power will not turn off when the LCD monitor and the viewfinder are closed and retracted.
≥ When playing back a motion picture recorded with other products on this unit or playing back a
motion picture recorded with this unit on other products, the picture quality may deteriorate and it may
be unplayable. (The message “CANNOT PLAY.” appears.)
≥ The time displayed may be different from the recording time and it may take time to display the
thumbnail display when playing back motion pictures recorded on another product.
To display the recording date during playback
Press the MENU button, then select [SETUP] # [DATE/TIME] # [D/T] or [DATE] and press the
joystick.
≥ You can also show or change the date and time display by repeatedly pressing the DATE/TIME
button on the remote control. (VDR-D310)
≥ The recording time is not displayed on the screen during playback of scenes recorded on other
products.
Fast forward/rewind playback
Move and hold the joystick right during playback until
fast-forward starts.
(Move and hold the joystick left to rewind.)
≥ Move the joystick again to increase the speed.
≥ Normal playback is restored when you move the joystick up.
∫ Operating with the remote control (VDR-D310)
Press the 6 or 5 button.
SEARCH
STILL ADV
SKIP
PLAY
PAUSE
STOP
SEARCH
STILL ADV
SKIP
Slow-motion playback
1 Move the joystick up during playback to pause the playback.
2 Move and hold the joystick right.
(Slow-motion pictures will be played back in
reverse when you move and hold the joystick left.)
≥ Normal playback is restored when you move the joystick up.
58
LSQT1161
Playback
∫ Operating with the remote control (VDR-D310)
Press the E or D button.
SEARCH
STILL ADV
SKIP
PLAY
PAUSE
STOP
SEARCH
STILL ADV
SKIP
Frame-by-frame playback
The motion picture is advanced one frame at a time.
1 Move the joystick up during playback to pause the playback.
2 Move the joystick right.
(The frames will be advanced one at a time in the
reverse direction when you move the joystick left.)
≥ Normal playback is restored when you move the joystick up.
∫ Operating with the remote control (VDR-D310)
1
Press the ; button.
SEARCH
STILL ADV
SKIP
PLAY
PAUSE
STOP
SEARCH
STILL ADV
SKIP
2
Press the E or D button.
SEARCH
STILL ADV
SKIP
PLAY
PAUSE
STOP
SEARCH
STILL ADV
SKIP
To adjust the volume
Adjust the speaker volume during playback.
Move the volume lever to change the volume
level.
Towards “r”: increases the volume
Towards “s”: decreases the volume
≥ The further the [ ] indicator moves to the right, the higher
the volume level becomes.
≥ When the adjustment is completed, the volume setting display will disappear.
59
LSQT1161
Playback
Playing back motion pictures by date
Recorded scenes are grouped by date on this unit.
Scenes recorded on the same day can be played back in succession.
1 Press the MENU button, then select
[PLAY SETUP] # [PLAY MODE] #
[BY DATE] and press the joystick.
≥ When [PLAY MODE] is set to [VIEW ALL], all
recorded motion pictures will be played back in
succession.
MENU
2 Select the date for playback, then press the
joystick.
The scenes recorded on the same day are displayed as thumbnails.
3 Select the scene to be played back.
≥ Even if scenes are recorded on the same day, they are grouped separately in the following cases.
jWhen the number of scenes exceeds 99 (RAM) (-RW‹VR›) (-RW‹V›) (-R)
jWhen the disc is removed (-RW‹V›) (-R)
jWhen the [REC ASPECT] setting is changed (-RW‹V›) (-R)
jWhen the disc is repaired (-RW‹V›) (-R)
jWhen the layers switch on a DVD-R DL (-R)
Resuming the previous playback
Press the MENU button, then select
[PLAY SETUP] # [RESUME PLAY] #
[ON] and press the joystick.
MENU
If playback of a motion picture is stopped, [R]
appears on the thumbnail view of the stopped
scene.
≥ If playback is stopped at any point during a motion
picture while [RESUME PLAY] is set to [OFF], the
next time the motion picture is played back, it will
be from the beginning.
≥ The resume position memorized is cleared if you open the disc cover or operate the mode dial, etc.
(The [RESUME PLAY] setting is kept.)
60
LSQT1161
Playback
Still picture playback (JPEG still pictures)
(SD)
Play back the still pictures recorded on the card.
1 Rotate the mode dial to select
The still pictures recorded on the SD card are
displayed as thumbnails.
.
2 Select the file to be played back.
A
B
File number
Scroll bar display
A
The selected file will be encircled by a yellow frame.
≥ When 9 or more files have been recorded, the next (or previous) page
is displayed by moving the joystick.
≥ If you move and hold the joystick up or down, you can advance 8 files
at a time. The screen will not change at this time, but the file numbers
and scroll bar display will change so release the joystick when you
have arrived at the page with the file you want to display.
B
3 Press the joystick.
The selected file is played back on the full screen.
The operation icon is automatically displayed on the screen.
4 Move the joystick to operate.
1/;: Slide show (playback of the still pictures on the SD card in numerical order) start/pause.
E:
D:
∫:
Plays back the previous picture.
Plays back the next picture.
Stops the playback and shows the thumbnails.
∫ About still picture compatibility
≥ This unit is compliant with the unified standard DCF (Design rule for Camera File system) established
by JEITA (Japan Electronics and Information Technology Industries Association).
≥ The file format supported by this unit is JPEG. (Not all JPEG formatted files will be played back.)
≥ If a non-standard file is played back, the folder/file number may not be displayed.
≥ This unit may degrade or not play back data recorded or created on another product and another
product may degrade or not play back data recorded on this unit.
≥ Do not operate the mode dial during the slide show.
≥ While this unit accesses the SD card (the access lamp is lit), do not remove the SD card.
61
LSQT1161
Playback
≥ It takes time to display the file depending on the number of pixels of the file.
≥ When a file is displayed as [
] on the thumbnail display, playback is not possible.
≥ If you attempt to play back file recorded in a different format or file data is defective, an error message
may appear.
≥ The time displayed may be different from the recording time and it may take time to display the
thumbnail display when playing back still pictures recorded on another product.
≥ The power will not turn off when the LCD monitor and the viewfinder are closed and retracted.
62
LSQT1161
Editing
Editing
2 Select [SELECT] or [ALL] and
Editing scenes
press the joystick.
≥ When [ALL] is selected, the following scenes
will be deleted. Proceed to step 5.
jWhen [PLAY MODE] is set to [VIEW ALL]:
All the scenes on the disc
jWhen [PLAY MODE] is set to [BY DATE]:
All the scenes selected by date
Deleting scenes
This is for deleting scenes recorded
on discs.
(RAM) (-RW‹VR›)
The deleted scenes cannot be restored.
≥ Scenes on DVD-RW (Video format) and DVD-
R cannot be deleted.
3
(Only when [SELECT] is selected in step 2)
Select the scene to be deleted,
then press the joystick.
Deleting scenes one at a time
¬Rotate the mode dial to select
.
1 Press the button during
playback.
The selected scene is encircled by a red frame.
≥ When the joystick is pressed again, the
selected scene will be cancelled.
≥ Up to 8 scenes displayed on a page can be set
in succession.
4
(Only when [SELECT] is selected in step 2)
Press the button.
2 When the confirmation message
appears, select [YES], then press
the joystick.
5 When the confirmation message
appears, select [YES], then press
the joystick.
Deleting multiple scenes from the
thumbnail display
(Only when [SELECT] is selected in step 2)
To continue deleting other scenes
Repeat steps 3-5.
¬Rotate the mode dial to select
.
1 Press the button in the
To complete editing
Press the MENU button.
thumbnail display.
≥ You can also delete scenes by pressing the
MENU button, selecting [EDIT SCENE] #
[DELETE] and then selecting [SELECT] or
[ALL].
≥ To delete an unwanted part of a scene, divide
the scene first, and then delete the
unnecessary part. (l 64)
≥ In case of [ALL], the deletion may take time if
there are many scenes on the disc.
63
LSQT1161
Editing
≥ Do not turn off this unit while deleting.
≥ When you delete scenes, use a battery with
sufficient battery power or use the AC adaptor.
≥ It may not be possible to delete scenes that
have been divided. Combine the divided
scenes, and then delete them.
move the joystick down to set the
dividing point.
Dividing a scene
This is for dividing a scene into two.
≥ Using slow-motion playback or frame-by-frame
playback makes it easy to search for the point
where you want to divide the scene. (l 58)
(RAM) (-RW‹VR›)
To delete an unnecessary portion of a scene, first
divide the scene and then delete the
unnecessary portion.
4 When the confirmation message
appears, select [YES], then press
the joystick.
¬Rotate the mode dial to select
.
1 Press the MENU button, then
select [EDIT SCENE] # [DIVIDE]
To continue dividing other scenes
Repeat steps 2-4.
# [YES] and press the joystick.
To complete editing
Press the MENU button.
MENU
Combining scenes
This function is only for combining
two consecutive scenes into one.
(RAM) (-RW‹VR›)
2 Select the scene to be divided,
¬Rotate the mode dial to select
.
then press the joystick.
1 Press the MENU button, then
select [EDIT SCENE] #
[COMBINE] # [YES] and press
the joystick.
The selected scene is played back.
MENU
3 When you reach the area where
you want to divide the scene,
64
LSQT1161
Editing
≥ If you create or delete playlists, the original
scenes will not be modified. Editing scenes on
a playlist will not affect the original scenes.
2 Select the scene to be combined,
then press the joystick.
A
B
≥ The selected scene and the next scene are
combined.
≥ If you wish to combine scenes that are not next
to each other or scenes with different recording
dates, first create a playlist and then combine
the scenes on the playlist. (l 65, 69)
3 When the confirmation message
appears, select [YES], then press
the joystick.
A
B
Recorded scenes
Playlist
To continue combining other scenes
Repeat steps 2-3.
≥ The maximum number of items on a disc (per
side)
jPlaylists: 99
To complete editing
Press the MENU button.
jPlaylist scenes: 999
≥ If original scenes are deleted, the portion of
playlists created with these scenes is also
deleted.
Using playlists
What is a playlist?
Creating a new playlist
You can create a playlist by gathering your
favourites from the recorded scenes.
Since the playlist is not created by copying data,
you will consume little of the disc capacity by
making a playlist.
(RAM) (-RW‹VR›)
¬Rotate the mode dial to select
.
1 Press the MENU button, then
select [PLAY SETUP] #
[PLAYLIST] # [CREATE] and
press the joystick.
MENU
65
LSQT1161
Editing
2 Select the scene to be added to
the playlist, then press the
joystick.
[PLAYLIST] # [VIEW LIST] and
press the joystick.
MENU
The selected scene is encircled by a red frame.
≥ When the joystick is pressed again, the
selected scene will be cancelled.
2 Select the playlist to be played
back, then press the joystick.
≥ Up to 50 scenes can be set in succession.
≥ The scenes are registered in the playlist in the
order that they were selected. After creating a
playlist, the order of the scenes in it can be
changed with the [MOVE] function. (l 68)
Scenes in the selected playlist are displayed as
thumbnails.
3 Press the MENU button.
4 When the confirmation message
3 Select the scene to start
appears, select [YES], then press
playback, then press the joystick.
the joystick.
The thumbnail view screen of the created playlist
is displayed.
To add another scene to the same
playlist
Select [ADD]. (l 67)
To select a different playlist
Press the MENU button, then select
[PLAYLIST VIEW] and press the joystick.
To playback a playlist
Select the scene to start playback, then press the
joystick.
To return to showing the original scenes
Press the MENU button, then select [END] and
press the joystick.
Playing back a playlist
(RAM) (-RW‹VR›)
¬Rotate the mode dial to select
.
Editing a playlist
1 Press the MENU button, then
(RAM) (-RW‹VR›)
select [PLAY SETUP] #
Editing scenes on a playlist will not affect the
original scenes.
66
LSQT1161
Editing
3
(Only when [SELECT] is selected in step 2)
Select the scene to be deleted,
then press the joystick.
Deleting scenes
≥ Deleting scenes on a playlist will not affect the
original scenes.
∫ Deleting scenes one at a time
¬Select playlist playback mode. (l 66,
steps 1 and 2)
1 Press the button during
The selected scene is encircled by a red frame.
≥ When the joystick is pressed again, the
selected scene will be cancelled.
playback.
≥ Up to 8 scenes displayed on a page can be set
in succession.
4
(Only when [SELECT] is selected in step 2)
Press the button.
5 When the confirmation message
appears, select [YES], then press
the joystick.
2 When the confirmation message
appears, select [YES], then press
the joystick.
(Only when [SELECT] is selected in step 2)
To continue deleting other scenes
Repeat steps 3-5.
∫ Deleting multiple scenes from
the thumbnail display
¬Select playlist playback mode. (l 66,
steps 1 and 2)
To complete editing
Press the MENU button.
1 Press the button in the
thumbnail display.
≥ You can also delete scenes by pressing the
MENU button, selecting [EDIT] # [DELETE]
and then selecting [SELECT] or [ALL].
≥ Deleting scenes on a playlist will not increase
the remaining capacity for recording.
≥ The playlist itself is deleted if you delete all the
scenes in it.
≥ When a playlist is deleted, the number of each
subsequent playlist decreases by one.
≥ It may not be possible to delete scenes that
have been divided. Combine the divided
scenes, and then delete them.
2 Select [SELECT] or [ALL] and
press the joystick.
≥ When [ALL] is selected, the selected playlist
Adding scenes to playlist
will be erased. Proceed to step 5.
¬Select playlist playback mode. (l 66,
steps 1 and 2)
67
LSQT1161
Editing
1 Press the MENU button, then
select [EDIT] # [ADD] # [YES]
and press the joystick.
1 Press the MENU button, then
select [EDIT] # [MOVE] # [YES]
and press the joystick.
MENU
MENU
2 Select the scene to be added,
2 Select the scene to be moved,
then press the joystick.
then press the joystick.
The selected scene is encircled by a red frame.
≥ When the joystick is pressed again, the
selected scene will be cancelled.
The selected scene is encircled by a red frame,
and the position to insert is shown by a yellow
bar.
≥ Up to 50 scenes can be set in succession.
≥ The scenes are added to the playlist in the
order that they were selected. The order of the
scenes in the playlist can be changed by
[MOVE] function. (l 68)
3 Select the position to insert the
scene, then press the joystick.
3 Press the MENU button.
4 When the confirmation message
appears, select [YES], then press
the joystick.
The thumbnail view screen of the playlist that
scenes were added to is displayed.
To continue moving other scenes in the
playlist
Repeat steps 2-3.
To complete editing
Press the MENU button.
To continue adding scenes to the
playlist
Repeat steps 1-4.
Dividing a scene
Moving scenes
You can divide a scene into two parts.
≥ Dividing scenes on a playlist will not affect the
original scenes.
The scenes in a playlist can be moved.
¬Select playlist playback mode. (l 66,
steps 1 and 2)
¬Select playlist playback mode. (l 66,
steps 1 and 2)
68
LSQT1161
Editing
1 Press the MENU button, then
select [EDIT] # [DIVIDE] # [YES]
and press the joystick.
Combining scenes
Two consecutive scenes can be combined into
one.
≥ Combining scenes on a playlist will not affect
the original scenes.
MENU
¬Select playlist playback mode. (l 66,
steps 1 and 2)
1 Press the MENU button, then
select [EDIT] # [COMBINE] #
[YES] and press the joystick.
2 Select the scene to be divided,
then press the joystick.
MENU
The selected scene is played back.
2 Select the scene to be combined,
3 When you reach the area where
you want to divide the scene,
move the joystick down to set the
dividing point.
then press the joystick.
≥ The selected scene and the next scene are
combined.
3 When the confirmation message
appears, select [YES], then press
the joystick.
≥ Using slow-motion playback or frame-by-frame
playback makes it easy to search for the point
where you want to divide the scene. (l 58)
4 When the confirmation message
appears, select [YES], then press
the joystick.
To continue combining other scenes
Repeat steps 2-3.
To complete editing
Press the MENU button.
To continue dividing other scenes
Repeat steps 2-4.
To complete editing
Press the MENU button.
69
LSQT1161
Editing
≥ When [ALL] is selected, all files on the SD card
except the locked files will be erased. Proceed
to step 5.
Editing still pictures
Deleting still pictures
This is for deleting still picture files
recorded on SD cards.
3
(Only when [SELECT] is selected in step 2)
Select the file to be deleted, then
press the joystick.
(SD)
The deleted files cannot be restored.
Deleting files one at a time
¬Rotate the mode dial to select
.
The selected file is encircled by a red frame.
≥ When the joystick is pressed again, the
selected file will be cancelled.
≥ Up to 8 files displayed on a page can be set in
succession.
1 Press the button during
playback.
4
(Only when [SELECT] is selected in step 2)
Press the button.
5 When the confirmation message
appears, select [YES], then press
the joystick.
2 When the confirmation message
appears, select [YES], then press
the joystick.
(Only when [SELECT] is selected in step 2)
To continue deleting other files
Repeat steps 3-5.
Deleting multiple files from the
thumbnail display
To complete editing
Press the MENU button.
¬Rotate the mode dial to select
.
1 Press the button in the
∫ Deleting still picture files recorded on an
SD card by other products
thumbnail display.
A still picture file (other than JPEG) that cannot
be played back on this unit may be erased.
≥ You can also delete files by pressing the
MENU button, selecting [PHOTO SETUP] #
[DELETE] and then selecting [SELECT] or
[ALL].
≥ In case of [ALL], the deletion may take time if
there are many files on the SD card.
≥ Do not turn off this unit while deleting.
≥ When you delete files, use a battery with
sufficient battery power or use the AC adaptor.
≥ Do not remove the SD card while deleting.
2 Select [SELECT] or [ALL] and
press the joystick.
70
LSQT1161
Editing
≥ If files conforming to DCF standard are
deleted, all the data related to the files will be
deleted.
DPOF setting
This is for writing the printing data on
an SD card.
Locking still pictures
This is for preventing still picture files
from being deleted by mistake.
(SD)
You can write the data of the still pictures to be
printed and the number of prints (DPOF data)
onto the SD card.
(SD)
Still picture files recorded on an SD card can be
locked so that they are not deleted by mistake.
(However even if you lock some files on an SD
card, formatting the card will delete all the files.)
¬Rotate the mode dial to select
.
1 Press the MENU button, then
select [PHOTO SETUP] #
[DPOF SET] # [SET] and press
¬Rotate the mode dial to select
.
the joystick.
1 Press the MENU button, then
select [PHOTO SETUP] #
[LOCK] # [YES] and press the
joystick.
MENU
MENU
2 Select the file to be set, then
press the joystick.
2 Select the file to be protected,
then press the joystick.
The number of prints set to be in DPOF is
displayed.
3 Move the joystick up or down to
[
] display appears and the selected file is
select the number of prints, then
locked.
press the joystick.
≥ Press the joystick again to release the lock
setting.
≥ You can also select multiple files in succession.
≥ You can select from 0 to 999. (The selected
number of pictures can be printed with the
printer supporting DPOF.)
≥ To cancel the setting, set the number of prints
to [0].
≥ You can also select multiple files in succession.
To complete the settings
Press the MENU button.
To complete the settings
Press the MENU button.
71
LSQT1161
Editing
To cancel all DPOF settings
Press the MENU button, then select
[PHOTO SETUP] # [DPOF SET] #
[CANCEL ALL] and press the joystick.
≥ When the confirmation message appears,
select [YES], then press the joystick.
∫ What is DPOF?
DPOF stands for Digital Print Order Format. This
enables picture printing information to be written
onto an SD card so that it can be used on a
system supporting DPOF.
≥ The DPOF setting can be established for up to
999 files.
≥ DPOF setting made on other devices may not
be recognized by this unit. Please perform the
DPOF settings on this unit.
≥ You cannot add the recording date to pictures
to be printed with the DPOF settings.
72
LSQT1161
Disc and card management
Disc and card management
[FINALIZE] # [YES] and press
the joystick.
Disc management
Finalizing a disc
It allows the discs to be played on
other devices.
MENU
(-RW‹VR›) (-RW‹V›) (-R)
If you insert a DVD-RW or a DVD-R disc
recorded in this unit (that has not been
finalized) into another device such as DVD
recorder, computer, etc., the disc may
become unusable.
3 When the confirmation message
appears, select [YES], then press
the joystick.
Be sure to finalize the disc on this unit before
inserting it in other devices.
When finalizing a DVD-RW (Video format) or
DVD-R, a top menu containing thumbnails is
created.
≥ When finalizing is complete, press the MENU
button to exit the message screen.
DVD-RAM:
≥ It is not necessary to finalize DVD-RAM.
DVD-RW (VR format):
≥ DVD-RW (VR format) after finalization can
be recorded and edited in the same way as
DVD-RW (VR format) before finalization.
≥ After finalizing a DVD-RW (VR format) once,
you cannot finalize it again. (Even if you
record on or edit a DVD-RW (VR format)
after finalizing, it is not necessary to finalize
it again.)
DVD-RW (Video format), DVD-R:
≥ After finalizing, the disc becomes play-only
and you can no longer record.
≥ When you un-finalize a DVD-RW (Video
format), the disc can be used for recording
again. (l 74)
≥ Do not finalize a disc recorded on this unit
using any other device.
≥ In the case of a double sided disc, finalize each
side.
≥ The top menu created when finalizing does not
appear on this unit. Play back the disc on a
DVD player.
Titles are displayed by recording date on the
top menu. However, when [PLAY MODE] is set
to [BY DATE] to view scenes by recording
date, some scenes recorded on the same date
may be separated. (l 60) These scenes will
be displayed as separate titles on the top
menu.
≥ It may take time to finalize a disc.
≥ If this unit becomes hot or is shaken strongly or
impacted while finalizing, the finalization will
fail and the disc may become unplayable on
other devices.
≥ If the power supply stops while finalizing, the
finalization will fail and the disc may become
unplayable on other devices even if disc repair
is carried out.
¬Rotate the mode dial to select
.
1 Connect this unit to the AC
adaptor.
≥ Finalization cannot be executed when using a
battery. If the power supply stops while
finalizing, the finalization will fail and the data
may be damaged. Use the AC adaptor.
2 Press the MENU button, then
select [DISC SETUP] #
73
LSQT1161
Disc and card management
[DISC PROTECT] and press the
joystick.
Un-finalizing a DVD-RW
This is for un-finalizing a DVD-RW
(Video format) so that it can be used
for recording.
MENU
(-RW‹V›)
¬Rotate the mode dial to select
.
1 Press the MENU button, then
select [DISC SETUP] #
[UN-FINALIZE] # [YES] and
press the joystick.
2 When the confirmation message
appears, select [YES], then press
the joystick.
To release disc protection
MENU
1) Press the MENU button, then select
[DISC SETUP] # [DISC PROTECT] and
press the joystick.
2) When the confirmation message appears,
select [YES], then press the joystick.
≥
If the disc has been protected on another device,
it may not be possible to release the protection on
this unit. In this case, release the protection on the
device that you used to protect it.
2 When the confirmation message
appears, select [YES], then press
the joystick.
≥ When un-finalizing is complete, press the
MENU button to exit the message screen.
Formatting discs
This is for initializing discs.
≥ DVD-RW (VR format) cannot be un-finalized.
DVD-RW (VR format) after finalization can be
recorded and edited in the same way as DVD-
RW (VR format) before finalization.
(RAM) (-RW‹VR›) (-RW‹V›)
Please be aware that if a disc is formatted, then
all the data recorded on the disc will be erased.
≥ DVD-R cannot be un-finalized.
≥ When you un-finalize the disc, use a battery
with sufficient battery power or the AC adaptor.
¬Rotate the mode dial to select
or
.
Protecting a disc
1 Press the MENU button, then
select [DISC SETUP] #
(RAM) (-RW‹VR›)
[FORMAT DISC] # [YES] and
press the joystick.
This is for preventing recorded contents from
being deleted or edited by mistake.
Further recording and editing is not possible on
protected discs until the protection is released.
MENU
¬Rotate the mode dial to select
.
1 Press the MENU button, then
select [DISC SETUP] #
74
LSQT1161
Disc and card management
≥ When formatting a DVD-RAM, skip to step 3.
Press the MENU button, then select
[DISC SETUP] # [INFORMATION] #
[YES] and press the joystick.
2
(When formatting a DVD-RW only)
Select format type (l 17), then
press the joystick.
MENU
To exit the information screen
Press the MENU button.
3 When the confirmation message
appears, select [YES], then press
the joystick.
≥ When formatting is complete, press the MENU
Card management
button to exit the message screen.
Formatting an SD card
This is for initializing cards.
≥ In the case of a double sided disc, format each
side.
≥ It may not be possible to format a disc with
many scratches or dirt. Such discs cannot be
used.
≥ During formatting, do not turn this unit off.
≥ When you format the disc, use a battery with
sufficient battery power or the AC adaptor.
Formatting DVD-RAM:
≥ We recommend formatting on this unit. If
formatting on a computer, use the supplied
software (VDR-D310). For more details, refer
to the operating instructions of the software.
If you connect this unit to a computer to format
a DVD-RAM, you cannot use DVDForm to
physically format it. Use a separate DVD-RAM
drive to physically format a DVD-RAM.
Formatting DVD-RW:
(SD)
Please be aware that if an SD card is formatted,
then all the data recorded on the card will be
erased. Store important data on a computer, etc.
¬Rotate the mode dial to select
or
.
1 Press the MENU button, then
select [SETUP] #
[FORMAT CARD] # [YES] and
press the joystick.
MENU
≥ Format on this unit.
Displaying disc information
(RAM) (-RW‹VR›) (-RW‹V›) (-R)
Information such as the number of recorded
scenes, the remaining space and whether or not
the disc is finalized or protected is displayed.
2 When the confirmation message
appears, select [YES], then press
the joystick.
≥ When formatting is complete, press the MENU
button to exit the message screen.
¬Rotate the mode dial to select
or
.
75
LSQT1161
Disc and card management
≥ Use this unit to format SD cards. If an SD card
is formatted on other products (such as a
computer), the time spent for recording may
become longer and you may not be able to use
the SD card.
≥ Depending on the type of SD card being used,
it may take time to format.
≥ During formatting, do not turn this unit off.
≥ When you format the SD card, use a battery
with sufficient battery power or the AC adaptor.
≥ Do not remove the SD card while formatting.
76
LSQT1161
With other products
With other products
∫ If the image or audio from this unit is not
output on the TV
With a TV
≥ Check that the plugs are inserted as far as they
go.
≥ Check the connected terminal.
≥ Check the TV’s input setting (input switch).
(For more information, please read the
operating instructions for the TV.)
Playback on TV
(RAM) (-RW‹VR›) (-RW‹V›) (-R) (SD)
The motion pictures and still pictures recorded by
this unit can be played back on a TV.
≥ If the images are not displayed correctly on a
wide-screen TV, adjust the aspect setting on
the TV. (Refer to the operating instructions of
the TV for details.) If the pictures are displayed
squeezed horizontally on a regular TV (4:3),
change the [TV ASPECT] setting on this unit.
(l below)
≥ Use the AC adaptor to free you from worrying
about the battery running down.
1 Connect this unit and a TV.
∫ To watch images with a 16:9
aspect ratio on a regular TV (4:3)
When playing back motion pictures recorded with
a 16:9 aspect ratio ([REC ASPECT] was set to
[16:9]) or still pictures recorded with a 16:9
A
2
aspect ratio [[PICTURE SIZE] was set to [
]
S VIDEO IN
*
(VDR-D310)/[ 0.2 ] (VDR-D220)] on a TV with a
4:3 aspect ratio, the images may be squeezed
horizontally. In this case, change the menu
setting to play back the pictures in the original
aspect ratio. (Depending on the TV setting, the
pictures may not be displayed correctly. For
more information, please read the operating
instructions of your TV.)
VIDEO IN
AUDIO IN
A
AV/S cable (supplied)
≥ Insert the plugs as far as they will go.
* If the TV has an S Video terminal, also connect
the S Video plug to it. This allows you to enjoy
more beautiful pictures.
Press the MENU button, then select
[SETUP] # [TV ASPECT] # [4:3]
and press the joystick.
2 Turn on this unit, then rotate the
Example of images with a 16:9 aspect ratio on
a regular TV (4:3)
mode dial to select
or
.
3 Change the input channel on the
[TV ASPECT] setting
TV.
[16:9]
[4:3]
≥ The channel set will differ depending on the
terminal to which the unit is connected.
4 Start playback on this unit.
The image and audio are output on the TV.
≥ This function’s default setting is [16:9].
77
LSQT1161
With other products
∫ To display the on-screen
information on the TV
(VDR-D310)
Playing back a DVD-RAM or a
DVD-RW (VR format)
The information displayed on the screen
(operation icon and time code, etc.) can be
displayed on the TV.
(RAM) (-RW‹VR›)
1
[Only when playing back a DVD-RW (VR
format)]
Press the EXT DISPLAY button on
the remote control.
Finalize the disc on this unit.
(l 73)
START/
2 Insert the disc in the playback
PHOTO
SHOT
EXT
STOP
DISPLAY
device and then play it back.
DATE/
TIME
ZOOM
VOL
≥ Press the button again to erase the
information.
≥ The screen on this unit will not change.
≥ Playback is only possible on devices that
support 8 cm DVD-RAM or DVD-RW (VR
format). Refer to the operating instructions of
the playback device.
≥ You cannot record images that allow “One time
only recording” on a 8 cm disc.
With a DVD recorder/
player
Playback on DVD recorder,
DVD player, computer etc.
Playing back a DVD-RW (Video
format) or a DVD-R
≥ Do not insert a DVD-RW or a DVD-R disc
recorded in this unit (that has not been
finalized) into another device such as DVD
recorder, DVD player, computer, etc. as the
disc may become unusable.
(-RW‹V›) (-R)
1 Finalize the disc on this unit.
(l 73)
≥ If you insert a DVD-RW disc recorded in this
unit (that has not been finalized) into
another device such as DVD recorder,
computer, etc., a format message may
appear. Do not format the disc as all the
important data recorded on the disc will be
erased and cannot be recovered.
2 Insert the disc in the playback
device and then play it back.
≥ When playing back a disc on a DVD recorder/
player, place the device so that the disc lies
flat.
≥ Playback is possible on devices that support
8 cm DVD-Video, but playback on all DVD
players is not guaranteed.
≥ Playback of DVD-R DL is only possible on
devices that support 8 cm DVD-R DL. Refer to
78
LSQT1161
With other products
the operating instructions of the playback
device.
≥ The recording time is not displayed.
≥ If you dub images recorded on a DVD-RW
(Video format) or a DVD-R disc, the title name
of the images after dubbing becomes the date
they were dubbed.
Dubbing recordings onto a
DVD recorder’s hard disk
If you dub images directly from the disc or with
the AV/S cable and then play them back on a
wide-screen TV, they may be squeezed
horizontally. In this case, refer to the operating
instructions of the device you are dubbing to
or read the operating instructions of the wide-
screen TV and set the aspect setting to 16:9
(Full).
(RAM) (-RW‹VR›) (-RW‹V›) (-R)
If you have a DVD recorder with hard disk,
images recorded by this unit can be stored on
the hard disk.
≥ Do not insert a DVD-RW or a DVD-R disc
recorded in this unit (that has not been
finalized) into the DVD recorder as the disc
may become unusable.
≥ If you insert a DVD-RW disc recorded in this
unit (that has not been finalized) into the
DVD recorder, a format message may
appear. Do not format the disc as all the
important data recorded on the disc will be
erased and cannot be recovered.
≥ If you want to dub a disc that the DVD recorder
is not compatible with, connect this unit and the
DVD recorder with the AV/S cable and then
dub the disc. (l 80)
1
[Only when you dub a DVD-RW or a DVD-R]
Finalize the disc on the unit.
(l 73)
2 Insert the disc in the DVD
recorder, then dub the contents
onto the hard disk.
≥ For details on how to dub the images onto the
hard disk, refer to the operating instructions of
the DVD recorder.
≥ If your DVD recorder has an SD card slot, you
can write the still picture files recorded on an
SD card with this unit to a disc or the hard disk.
≥ You cannot record images that allow “One time
only recording” on a 8 cm disc.
79
LSQT1161
With other products
4 Start playback on this unit.
With a VCR
Then start recording on the
connected device.
≥ See the operating instructions of the video
device for details.
Dubbing images onto other
video devices
To stop dubbing
Stop recording on the connected device.
Then stop playback on this unit.
(RAM) (-RW‹VR›) (-RW‹V›) (-R)
You can dub images played back on this unit
onto other video devices.
You can create a playlist by gathering the scenes
you want to dub, then dub the scenes in this
playlist only to other devices. (l 65)
≥ If the date and time display and function
indication are unnecessary, cancel them
before dubbing. (VDR-D310) (l 35, 78)
≥ Use the AC adaptor to free you from worrying
about the battery running down.
With a printer (PictBridge)
1 Connect this unit and a video
(SD)
device.
To print pictures by directly connecting this unit to
the printer, use a printer compatible with
PictBridge. (Read the operating instructions for
the printer.)
≥ Use the AC adaptor to free you from worrying
about the battery running down.
¬Insert an SD card with recorded
images in the unit, then turn on the
unit.
A
S VIDEO IN
*
VIDEO IN
1 Connect this unit and a printer.
AUDIO IN
A
AV/S cable (supplied)
≥ Insert the plugs as far as they will go.
* If the video device has an S Video terminal,
also connect the S Video plug into it. This
allows you to enjoy more beautiful pictures.
A
2 Turn on this unit, then rotate the
mode dial to select
.
A
USB cable [supplied (VDR-D310)]
3 Change the input channel on the
≥ Insert the plugs as far as they will go.
≥ Do not use any other USB cables except the
supplied one. (Operation is not guaranteed
with any other USB cables.) (VDR-D310)
video device and TV.
≥ The channel set will differ depending on the
terminal to which the unit is connected.
80
LSQT1161
With other products
The USB function selection screen will appear.
7 Select the paper size setting on
[PAPER SIZE].
2 Select [PictBridge] and press the
joystick.
The [
] indication appears on this unit’s
screen.
3 Select a file to be printed, then
[STANDARD]: Size specific to the printer
[4t5 INCH]: L size
press the joystick.
[5t7 INCH]: 2L size
[4t6 INCH]: Postcard size
[A4]:
A4 size
≥ You cannot set paper sizes not supported on
the printer.
The number of pictures set is displayed.
8 Select the layout setting on
[PAGE LAYOUT].
4 Move the joystick up or down to
select the desired number of
prints, then press the joystick.
≥ You can set up to 9 prints.
≥ To cancel the setting, set the number of prints
to [0].
≥ Up to 8 files displayed on a page can be set in
succession by repeating steps 3 and 4.
[STANDARD]: Layout specific to the printer
5 Press the MENU button to
[
[
]:
]:
No frame print
Frame print
display the PictBridge menus.
≥ You cannot set page layouts not supported on
the printer.
MENU
9 Select [PRINT] # [YES] and
press the joystick.
The pictures are printed.
≥ Exit PictBridge by disconnecting the USB cable
after the pictures have been printed.
6 Select the date print setting on
When you stop printing halfway
Move the joystick down.
[DATE PRINT].
≥ If the printer is not capable of date printing, this
A confirmation message appears. If [YES] is
selected, the number of prints set is cancelled
and the screen returns to step 3. If [NO] is
selected, all the settings are kept and the screen
returns to step 3.
setting is unavailable.
81
LSQT1161
With other products
≥ Avoid the following operations during printing.
These operations disable proper printing.
jDisconnecting the USB cable
jRemoving the SD card
jSwitching the mode dial
jTurning off the power
≥ Check the settings for the paper size, quality of
print, etc. on the printer.
≥ The sides of pictures recorded when [
]
2
(VDR-D310)/[
] (VDR-D220) is set may be
0.2
cut at printing. Check before printing.
When using a printer with a trimming or
borderless printing function, cancel this
function before printing. (Refer to the operating
instructions of the printer for details.)
≥ You may not be able to print still pictures
recorded with other products.
≥ When the unit is connected directly to the
printer, the DPOF settings cannot be used.
≥ Connect the printer directly to this unit. Do not
use a USB hub.
82
LSQT1161
Others
Others
Still picture recording menus
Menus
Menu list
Motion picture recording menus
∫ [BASIC]
[SCENE MODE] (l 52)
[GUIDE LINES] (l 51)
[PICTURE SIZE] (l 45)
[PICT.QUALITY] (l 45)
[CLOCK SET] (l 35)
∫ [BASIC]
[SCENE MODE] (l 52)
[GUIDE LINES] (l 51)
[REC MODE] (l 40)
[REC ASPECT] (l 51)
[CLOCK SET] (l 35)
∫ [ADVANCED]
[O.I.S.] (l 51)
[SHTR EFFECT] (l 44)
∫ [SETUP]
[DISPLAY] (l 84)
∫ [ADVANCED]
[DATE/TIME] (l 35)
[DATE FORMAT] (l 35)
[FORMAT CARD] (l 75)
[POWER SAVE] (l 84)
[BEEP SOUND] (l 84)
[LCD SET] (l 36)
[D.ZOOM] (l 46)
[O.I.S.] (l 51)
[FADE COLOUR] (l 48)
[WIND CUT] (l 52)
[ZOOM MIC] (l 47)
[EVF SET] (l 36)
[INITIAL SET] (l 85)
[DEMO MODE] (l 85)
∫ [DISC SETUP]
[FORMAT DISC] (l 74)
[INFORMATION] (l 75)
∫ [LANGUAGE] (l 33)
∫ [SETUP]
[DISPLAY] (l 84)
Motion picture playback menus
[DATE/TIME] (l 35)
[DATE FORMAT] (l 35)
[POWER SAVE] (l 84)
[AGS] (VDR-D310) (l 38)
[BEEP SOUND] (l 84)
[LCD SET] (l 36)
[EVF SET] (l 36)
[INITIAL SET] (l 85)
[DEMO MODE] (l 85)
∫ [PLAY SETUP]
[PLAY MODE] (l 60)
[RESUME PLAY] (l 60)
[PLAYLIST] (l 65, 66)
∫ [LANGUAGE] (l 33)
∫ [EDIT SCENE]
[DIVIDE] (l 64)
[COMBINE] (l 64)
83
LSQT1161
Others
[DELETE] (l 63)
[DATE FORMAT] (l 35)
[FORMAT CARD] (l 75)
[POWER SAVE] (l 84)
[BEEP SOUND] (l 84)
[LCD SET] (l 36)
∫ [DISC SETUP]
[FINALIZE] (l 73)
[UN-FINALIZE] (l 74)
[DISC PROTECT] (l 74)
[FORMAT DISC] (l 74)
[INFORMATION] (l 75)
[EVF SET] (l 36)
[TV ASPECT] (l 77)
∫ [LANGUAGE] (l 33)
∫ [SETUP]
[DISPLAY] (l 84)
[DATE/TIME] (l 35)
[DATE FORMAT] (l 35)
[POWER SAVE] (l 84)
[BEEP SOUND] (l 84)
[LCD SET] (l 36)
[EVF SET] (l 36)
Other menus
∫ [DISPLAY]
≥ [OFF]
≥ [ON]
The screen indications are selected as shown in
the illustration below.
[OFF]
[TV ASPECT] (l 77)
;
∫ [LANGUAGE] (l 33)
(In playlist playback mode)
∫ [EDIT]
[ON]
SP
;
0h00m00s
[ADD] (l 67)
R
30min
[MOVE] (l 68)
[DIVIDE] (l 68)
[COMBINE] (l 69)
[DELETE] (l 67)
∫ [CREATE]
∫ [PLAYLIST VIEW]
∫ [END]
∫ [POWER SAVE]
≥ [OFF]
≥ [5 MINUTES]
[OFF]:
The power saving function is not activated.
[5 MINUTES]:
Still picture playback menus
When about 5 minutes have passed without any
operation, this unit automatically turns off to
prevent the battery from running down. When
you use this unit, turn it on again.
≥ In the following cases, the unit may not turn off
even when you set this to [5 MINUTES].
jWhen using the AC adaptor
jWhen connecting the unit to a computer or
printer via the USB cable
∫ [PHOTO SETUP]
[LOCK] (l 71)
[DPOF SET] (l 71)
[DELETE] (l 70)
∫ [BEEP SOUND]
≥ [OFF]
≥ [ON]
This allows operations such as starting and
ending recording to be signaled by a beep.
When [OFF] is set, no beep is heard when an
operation such as recording is started or ended.
∫ [SETUP]
[DISPLAY] (l 84)
[DATE/TIME] (l 35)
84
LSQT1161
Others
Indications
1 Beep
When you start recording
When you turn on the power
When this unit is recognized by the computer or
the printer, etc.
Indications
∫ Recording indications
Motion picture recording
2 Beeps
When you pause recording
When you turn off the power
2 Beeps for 4 times
SP
;
0h00m00s
R
30min
MNL
When an error occurs e.g. recording not starting.
Check the sentence displayed on the screen.
(l 88)
AWB
1
/
100
OPEN
0dB
15.12.2007 15:30
∫ [INITIAL SET]
Still picture recording
≥ [YES]
≥ [NO]
2
MEGA
R
100
When there is a menu that cannot be selected
due another function or mode being activated,
set to [YES] for changing the menu settings back
to the initial shipping condition.
MNL
AWB
1
/
100
OPEN
0dB
15.12.2007 15:30
(The language setting cannot be changed back
to the initial shipping condition.)
Remaining battery power
∫ [DEMO MODE]
R
0min
Remaining time for recording
Elapsed recording time
≥ [OFF]
≥ [ON]
This item is used to start the unit demonstration.
(Only when using the AC adaptor and the mode
dial is at the
0h00m00s
15.12.2007
15:30
Date/time indication
or
position)
If you set this to [ON] without inserting a disc or
an SD card, this unit is automatically set to the
demonstration mode for introducing its functions.
If any button is pressed or operated, the
demonstration mode is cancelled. If no
operations take place for approx. 10 minutes, the
demonstration mode automatically starts. To
terminate the demonstration mode, insert a disc
or an SD card, or set this to [OFF]. For normal
use, set this function to [OFF].
¥/; (Red)
; (Green)
16:9
Recording/writing to a disc
Recording pause
Wide mode
Auto mode
AUTO
Manual mode
MNL
MF
Manual focus
2t
Zoom magnification indication
Back light mode
Image stabilizer
Shutter speed
ª
1/100
OPEN, F2.0
0dB
F number
Gain value
Soft skin mode
Tele macro
,
Fade (White), Fade (Black)
Colour night view function
85
LSQT1161
Others
∫ Playback indications
Zoom microphone
ZOOM
Motion picture playback
Wind noise reduction
,
,
Motion picture recording mode
XP
SP
LP
5
Sports mode
Portrait mode
Low light mode
Spotlight mode
Surf & snow mode
Still picture playback
Auto white balance
AWB
Indoor mode (recording under
incandescent lamp)
Outdoor mode
Manual adjustment mode
Disc type
DVD-RAM
1
;
Playback
Pause
DVD-RW (VR format)
DVD-RW (Video format)
DVD-RW (unformatted)
DVD-R
5,
6,
/
Fast forward/rewind
DVD-R DL
7/8
Last/first scene paused
Skip playback
± (White)
¥ (Green)
Shutter chance mark
9/:
D/E
Slow motion playback
Frame-by-frame playback
Motion picture playback time
Ø
Self-Timer recording
MEGA OIS
;1/2;
0h00m00s
MEGA
Number of recording pixels for
still pictures
Play mode
VDR-D310:
All scenes on the disc
displayed
2048k1512
1920k1080
3.1M
2
01
01
Scenes recorded on the
selected date displayed
Scenes in the selected playlist
displayed
1
M
1280k960
640k480
0.3M
VDR-D220:
0.3M
640k480
0.2
640k360
No.10
R
Scene number
(White)
(Green)
(Red)
Card can be recorded to
Recognizing the card
Recording/accessing the card
Volume adjustment
Resume playback
Contents that have been
protected on another device.
,
Still picture quality
Remaining number of still
pictures
R 100
Still picture folder/file number
display
100-0001
When a printer compatible with
PictBridge is connected
Accessing the card (When
connected to a computer)
DPOF already set
(to more than 1)
1
86
LSQT1161
Others
Locked still pictures
Number of recording pixels for
still pictures
VDR-D310:
2048k1512
3.1M
1920k1080
2
1
M
1280k960
0.3M
640k480
VDR-D220:
0.3M
640k480
640k360
0.2
The picture size is not displayed for still
pictures recorded with other products that have
different picture sizes from the sizes shown
above.
∫ Confirmatory indications
–– (Time
display)
The built-in battery is low.
(l 36)
The warning/alarm indication
appears when LCD monitor is
rotated towards the lens side.
Return the direction of the LCD
monitor to normal position and
check the warning/alarm
indication.
°
No disc is inserted.
Unusable disc
No SD card is inserted/
unusable card.
87
LSQT1161
Others
Messages
CAN NOT READ THIS
DISC. PLEASE CHECK
FOR SCRATCHES OR
STAINS ON DISC.
The disc is scratched or dirty. Eject the disc and clean it. (l 20) If
there are scratches on the disc, use a new disc.
NO DATA.
There are no images recorded on the disc or card.
INCOMPATIBLE DISC.
You inserted an incompatible disc (copy-protected discs, etc.).
PLEASE CHECK THE
DISC.
You inserted a disc that cannot be read on this unit (a disc recorded
in an incompatible data format etc.).
You inserted a disc that does not meet the DVD standard for quality
and performance so you may not be able to record normally. Refer
to the following support site for information about discs that have
been confirmed as compatible by Panasonic.
FOR BEST
PERFORMANCE
PANASONIC DISC IS
RECOMMENDED.
http://panasonic.co.jp/pavc/global/cs/e_cam
(This website is in English only.)
CANNOT RECORD IN AGS
MODE.
The AGS function is activated. (l 38)
A finalized DVD-RW (Video format) or DVD-R has been inserted.
After finalizing, the discs become play-only and cannot record. If you
un-finalize a DVD-RW (Video format), it can be used for recording.
(l 74)
CANNOT RECORD.
(THIS DISC IS FINALIZED)
CANNOT RECORD. DISC
IS FULL.
The disc is full or the number of scenes has reached the maximum
limit so no further data can be recorded. Delete unnecessary scenes
(l 63) or insert a new disc.
CANNOT RECORD. THE
NUMBER OF SCENES HAS
EXCEEDED THE MAXIMUM
LIMIT.
INTERNAL TEMPERATURE
TOO HIGH. PLEASE TURN
UNIT OFF AND WAIT A
WHILE.
The temperature of the unit is high so it cannot be operated. Turn off
the power, wait until the unit cools and then turn on the power again.
If you insert a DVD-RW or a DVD-R disc recorded in this unit (that
has not been finalized) into another device such as DVD recorder,
computer, etc., the disc may become unusable. Be sure to finalize
the disc on this unit before inserting it in other devices.
FINALIZE THE DISC FOR
PLAYBACK ON OTHER
DEVICES.
CANNOT UN-FINALIZE
THIS DISC.
DVD-R cannot be un-finalized.
CHECK CARD.
CARD LOCKED.
This card is not compatible or it cannot be recognized by the unit.
The write protection switch on the SD card is set to LOCK. (l 19)
88
LSQT1161
Others
The SD card is full so no further data can be recorded. Delete
unnecessary files (l 70) or insert a new SD card.
CARD FULL.
PUSH THE RESET
SWITCH.
An irregularity in the unit has been detected. Press the RESET
CHECK THE DISC AFTER
PUSHING THE RESET
SWITCH TO REPAIR IT.
button to restart the unit. (l 95)
CHANGE TO MANUAL
MODE.
You are attempting to use a function that cannot be used
simultaneously.
CANCEL NIGHT VIEW
MODE
With DVD-RW (Video format) and DVD-R, if the number of dates
displayed becomes 99 when [PLAY MODE] is set to [BY DATE], you
cannot change the aspect setting from 16:9 to 4:3 and vice versa.
CANNOT SET.
PLEASE CONNECT AC
ADAPTOR
Finalizations cannot be executed and the unit cannot be connected
to the computer when using a battery. Use the AC adaptor.
The unit cannot correctly establish the connection to the computer
or printer. Disconnect and reconnect the USB cable and then select
the desired USB function again.
DISCONNECT USB
CABLE.
CANNOT OPERATE WHILE The unit’s power cannot be turned off when the unit is connected to
USB CONNECTED.
the computer.
About recovery
It is possible that the system cannot complete writing of a file normally when, for example, power is
turned off for some reason during recording or editing.
If faulty management information is found when a disc is accessed, the following message may appear.
Be sure to follow the messages. (Repairing may take time depending on the error.)
DISC ERROR HAS OCCURRED. NOW REPAIRING THE DISC.
≥ When you repair the disc, use a battery with sufficient battery power or the AC adaptor. Even if the
power is turned off without repairing the disc, you can repair the disc when you turn the power on
again.
≥ Depending on the condition of the data, it may not be possible to completely repair the data.
≥ Do not repair a disc that has been recorded on another device. This may cause the loss of data or the
disc.
89
LSQT1161
Others
Functions that cannot be used simultaneously
Some functions in this unit are disabled or cannot be selected due to the unit’s specifications.
The table below shows examples of functions restricted by various conditions.
Conditions which
disable the functions
Functions
Digital zoom
≥ In picture recording mode
Fade
≥ While recording to a disc (Cannot set or cancel)
≥ In picture recording mode
Colour night view
≥ When the colour night view function is used
Backlight compensation
≥ When the iris/gain is set
Soft skin mode (Set and cancel)
Tele macro (Set and cancel)
Help mode
≥ While recording to a disc
Zoom microphone
Wind noise reduction
≥ An external microphone is used
≥ When setting the AUTO/MANUAL/FOCUS switch
to AUTO
Scene mode
≥ When the colour night view function is used
≥ When digital zoom is used
≥ When the colour night view function is used
Change of white balance
≥ When the colour night view function is used
≥ When the scene mode is used
Adjusting the shutter speed, iris/gain
90
LSQT1161
Others
Frequently asked questions
What kind of discs can be used?
DVD-RAM, DVD-RW, DVD-R and DVD-R DL can be used if they are 8 cm bare discs.
(l 15)
Can discs with a cartridge be used?
They can be used if the cartridge is removed.
Can double sided discs be used?
They can be used.
However you cannot record or play continuously from one side of the disc to the other.
You will need to eject the disc and turn it over.
Can I record continuously from one side of the disc to the other on a double sided disc?
You cannot record continuously from one side of the disc to the other. The recording time
indicated on the disc package is the total time for both sides. You will need to eject the
disc and turn it over to record on both sides.
Can DVD-R only be recorded to once only?
Recording can be started and stopped until the disc is full.
However the data recorded on the DVD-R cannot be erased.
Is playback possible on a DVD player?
By finalizing a DVD-RW (VR format/Video format) or a DVD-R in this unit, it can be
played back on a DVD player.
To playback a DVD-RAM, DVD-RW (VR format) or DVD-R DL, you will need a DVD
recorder or a DVD player that supports DVD-RAM, DVD-RW (VR format) or DVD-R DL.
Refer to the operating instructions of the DVD recorder or DVD player.
91
LSQT1161
Others
Troubleshooting
Problem
Check points
≥ Is the battery fully charged?
# Charge the battery using the AC adaptor. (l 21)
≥ The battery protection circuit may have operated. Attach the
battery to the AC adaptor for 5 to 10 seconds. If the unit still
cannot be used, the battery is faulty.
This unit cannot be
turned on.
≥ Is the LCD monitor opened or the viewfinder extended?
≥ If you do not use the unit for approximately 5 minutes, the
power is automatically turned off to conserve the battery
charge. To resume recording, turn the power back on.
The power will not turn off automatically when the power save
function (l 84) is set to [OFF].
This unit is turned off
automatically.
≥ Is the battery low?
This unit does not stay
on long enough.
# If the remaining battery power indication is flashing or the
message “LOW BATTERY.” is displayed, the battery has run
down. Charge the battery. (l 21)
A clicking sound is heard
when the power is turned
off.
≥ This is the sound of the lens moving and is not a malfunction.
≥ Is the battery fully charged?
# Charge it with the AC adaptor. (l 21)
≥ Are you using the battery in an extremely cold place?
# The battery is affected by ambient temperature. In cold places,
the operating time of the battery becomes shorter.
≥ Has the battery worn out?
Battery runs down
quickly.
# The battery has a limited life. If the operating time is still too short
even after the battery is fully charged, the battery has worn out
and can no longer be used.
≥ The unit cannot be operated unless you open the LCD monitor
or extend the viewfinder.
This unit cannot be
operated though it is
turned on.
≥ Press the RESET button. (l 95) If normal conditions are not
restored yet, remove the battery or AC adaptor, wait about 1
minute and then reconnect the battery or AC adaptor. Then
about 1 minute later, turn on the power again. (Conducting the
above operation when the access lamp is on may destroy the
data on the disc or card.)
This unit does not
operate normally.
≥ Has the demonstration started?
# If you set [DEMO MODE] to [ON] without inserting a disc or a
card in video recording mode or picture recording mode, the unit
is automatically set to the demonstration mode for introducing its
functions. Normally this should be set to [OFF]. Press the MENU
button, then select [SETUP] # [DEMO MODE] # [OFF] and
press the joystick.
The screen has changed
suddenly.
92
LSQT1161
Others
Problem
Check points
The remote control does
not function.
≥ Has the button-type battery of the remote control run out?
# Replace it with a new button-type battery. (l 13)
≥ The disc cover will not open unless the unit is powered.
# Connect a charged battery or AC adaptor.
≥ The DISC EJECT lever does not work when the unit is
connected to the computer. (VDR-D310) (Refer to the operating
instructions for PC connection.)
The DISC EJECT lever
does not work.
≥ Are there fingerprints or dirt on the surface of the disc?
# If there are fingerprints or dirt on the disc, wipe them off. (l 20)
The disc cannot be read.
A function indication
such as the remaining
time indication or the
elapsed time indication is
not shown.
≥ If you set [SETUP]>[DISPLAY]>[OFF], indications other than
warnings and date indications disappear.
≥ Is the DVD-RAM or the DVD-RW (VR format) write-protected?
# Release the protection. (l 74) If the DVD-RAM or DVD-RW (VR
format) was protected on another device, release the protection
on the same device.
≥ Has the DVD-RW (Video format) or DVD-R been finalized?
# After finalizing, the discs become play-only and cannot record. If
you un-finalize a DVD-RW (Video format), it can be used for
recording. (l 74)
Recording does not start
although power is
supplied to this unit and
the disc or card is
≥ Has the SD card’s write protect switch been set to LOCK?
# No recording is possible while the write protect switch is set to
LOCK. (l 19)
≥ Is the memory of the disc or card full?
correctly inserted.
# If the disc or card has no more available memory, free up some
memory by deleting unnecessary scenes (l 63, 70) or use a
new disc or card.
≥ Is the unit set to the video recording mode or picture recording
mode?
# No recording is possible unless the mode dial is at
≥ Is the disc cover open?
or
.
# If the cover is open, this unit may not operate normally. Close the
disc cover.
≥ Is the disc scratched or dirty?
# Clean the disc. (l 20) If there are scratches on the disc, use a
new disc.
≥ The unit is hot. Follow the messages on the display.
To use the unit again, turn the unit off and leave it for a while.
Recording starts but
stops immediately.
The playback picture
breaks up for a moment.
≥ Is the AGS function activated?
# Record in the normal horizontal position or set [AGS] to [OFF].
(l 38)
The unit arbitrarily stops
recording.
93
LSQT1161
Others
Problem
Check points
≥ Are you trying to record small or finely detailed objects with
[PICT.QUALITY] set at [
# If you try to record small or finely detailed objects with
[PICT.QUALITY] set at [ ], the images may break up into a
]?
Recorded still pictures
are not clear.
mosaic-like pattern. Record with [PICT.QUALITY] set at [
]
instead. (l 45)
≥ Is manual focus mode selected?
# Set the AUTO/MANUAL/FOCUS switch to AUTO.
≥ Are you trying to record a scene which is hard to bring into
focus in auto focus mode?
# There are some recording subjects and surroundings for which
the auto focus does not operate correctly. (l 100) If so, use the
manual focus mode to adjust the focus. (l 53)
Auto focus function does
not work.
Sound is not played back
from the built-in speaker
of this unit.
≥ Is the volume too low?
# During playback, move the volume lever to display the volume
indication and adjust it. (l 59)
≥ Have you selected video input on the TV?
Although this unit is
correctly connected to a
TV, playback images
cannot be seen.
# Please read the operating instructions of your TV and select the
channel that matches the input used for the connection.
≥ Is the [TV ASPECT] setting correct?
# Change the setting to match the aspect ratio of the TV.
Press the MENU button, then select [SETUP] # [TV ASPECT]
# [16:9] or [4:3] and press the joystick.
The playback images are
squeezed horizontally.
≥ Is the DVD-RAM or the DVD-RW (VR format) write-protected?
# Release the protection. (l 74)
If the disc or the contents on the disc have been protected on
another device, release the protection on the same device.
≥ It may not be possible to delete scenes that have been divided.
# Combine the divided scenes, and then delete them. (l 64)
≥ It may not be possible to delete scenes that are displayed as
Scenes cannot be deleted
or edited.
[
] on the thumbnail display. If the scenes are unnecessary,
format the disc or card to erase the data. (l 74, 75) Please be
aware that if a disc or card is formatted then all the data
recorded on the disc or card will be erased.
≥ Is the file on the SD card locked?
# Locked files cannot be deleted. Release the lock setting. (l 71)
≥ If the SD card’s write protect switch is set to LOCK, then
deletion is disabled. (l 19)
≥ The data may be destroyed. It may have been destroyed by
static or electromagnetic waves. Store important data on a
computer or other products as well.
The images on the SD
card do not look normal.
Even if a disc or a card is
formatted, it cannot be
used.
≥ Either this unit or the disc or card may be damaged. Please
consult a dealer. Use an SD card from 8 MB to 4 GB with this
unit.
94
LSQT1161
Others
Problem
Check points
≥ Is this unit connected to a computer?
# No operation can be performed on this unit when it is connected
to a computer. (VDR-D310) (Refer to the operating instructions
for PC connection.)
The indication
disappears.
≥ Turn off the power to this unit. If the power cannot be turned
off, press the RESET button, or remove the battery or AC
adaptor and then reattach it. After that, turn on the power
again. If normal operation is still not restored, detach the
power connected, and consult the dealer who you purchased
this unit from.
The screen is frozen.
No operation can be
performed.
≥ Is the disc scratched or dirty?
# After using the following method to restart the unit, eject the disc
and clean it. (l 20) If there are scratches on the disc, use a new
disc.
≥ The unit has automatically detected an error. Press the RESET
button with the projecting part of the lens cap A. This will
restart the unit.
“PUSH THE RESET
SWITCH.” or “CHECK
THE DISC AFTER
A
PUSHING THE RESET
SWITCH TO REPAIR IT.”
is displayed.
≥ If you do not press the RESET button, the power to this unit is
turned off automatically about 1 minute later.
≥ Even after you press the RESET button, the indication may still
appear repeatedly. If so, this unit needs repair. Detach the
power connected, and consult the dealer who you purchased
this unit from. Do not attempt to repair the appliance by
yourself.
≥ Check that the device is compatible with the capacity or type of
SD card (SD Memory Card/SDHC Memory Card) that you
inserted.
If the SD card is inserted
in another device, it is not
recognized.
# Refer to the operating instructions of the device for details.
95
LSQT1161
Others
Do not spray insecticides or volatile
chemicals onto the unit.
Cautions for use
In the event of abnormal operation (e.g. if the unit
emits smoke or an unusual smell), immediately
stop operating the unit and consult the
≥ If the unit is sprayed with such chemicals, its
body may be marred and the surface finish
may peel off.
Panasonic Customer Care Centre on 132600.
≥ Do not leave rubber or plastic products in
contact with the unit for a long time.
About this unit
When you use the unit in a sandy or dusty
place such as a beach, do not let sand or fine
dust get into the body and terminals of the
unit.
≥ The unit, disc and card become warm after
long operation, but this is not a malfunction.
Also, keep the unit away from sea water.
≥ Sand or dust may damage the unit. (Care
should be taken when inserting and removing
a disc or a card.)
≥ If sea water splashes onto the unit, wipe off the
water with a well wrung cloth. Then wipe the
unit again with a dry cloth.
Keep the DVD Video Camera as far away as
possible from electromagnetic equipment
(such as microwave ovens, TVs, video games
etc.).
≥ If you use the DVD Video Camera on top of or
near a TV, the pictures and sound on the DVD
Video Camera may be disrupted by
electromagnetic wave radiation.
When carrying the unit, do not drop or bump
it.
≥ A strong impact can break the unit’s casing,
causing it to malfunction.
≥ Do not use the DVD Video Camera near cell
phones because doing so may result in noise
adversely affecting the pictures and sound.
≥ Recorded data may be damaged, or pictures
may be distorted, by strong magnetic fields
created by speakers or large motors.
≥ Electromagnetic wave radiation generated by
microprocessors may adversely affect the DVD
Video Camera, disturbing the pictures and
sound.
Do not use benzine, paint thinner or alcohol
for cleaning the unit.
≥ Before cleaning, detach the battery or pull out
the AC cable from the AC outlet.
≥ The camera body may be discoloured and the
surface finish may peel off.
≥ If the DVD Video Camera is adversely affected
by electromagnetic equipment and stops
functioning properly, turn the DVD Video
Camera off and remove the battery or
disconnect AC adaptor. Then reinsert the
battery or reconnect AC adaptor and turn the
DVD Video Camera on.
≥ Wipe the unit with a soft dry cloth to remove
dust and fingerprints. To remove stubborn
stains, thoroughly wring a cloth that has been
soaked in a neutral detergent diluted with
water and wipe the unit with it. Afterwards,
wipe it with a dry cloth.
≥ When you use a chemical dust cloth, follow the
instructions that came with the cloth.
Do not use the DVD Video Camera near radio
transmitters or high-voltage lines.
≥ If you record near radio transmitters or
high-voltage lines, the recorded pictures and
sound may be adversely affected.
Do not touch the laser pickup lens.
≥ If you touch the laser pickup lens directly it may
cause malfunctions.
Do not use any other lens cleaners except a
commercial available 8 cm DVD video camera
lens cleaner.
≥ Using any other lens cleaners except the one
for 8 cm DVD video camera could cause this
unit to malfunction.
Make sure to use the supplied cords and
cables. If you use optional accessories, use
the cords and the cables supplied with them.
Do not extend the cords and the cables.
96
LSQT1161
Others
Do not use the unit for surveillance purposes
or other business uses.
Prepare spare batteries when going out for
≥ If you use the unit for a long time, heat will
build up inside it and this may cause a
malfunction.
recording.
≥ Prepare batteries appropriate to 3 to 4 times
the period during you want to record pictures
in. In cold places such as a ski resort, the
period during which you can record pictures is
shortened.
≥ When you travel, do not forget to bring an AC
adaptor so that you can recharge the batteries
at your destination.
≥ This unit is not intended for business use.
When you are not going to use the unit for an
extended time
≥ When storing the unit in a cupboard or cabinet,
it is recommended that you place a desiccant
(silica gel) in with it.
If you drop the battery accidentally, check to
see if the terminals are damaged.
≥ Attaching a battery with damaged terminals
can damage the unit or AC adaptor.
About the battery
The battery used in this unit is a rechargeable
lithium-ion battery. It is susceptible to humidity
and temperature and the effect increases the
more the temperature rises or falls. In cold areas,
the full charge indication may not appear or the
low battery indication may appear about
5 minutes after starting use. At high
temperatures, the protection function may be
triggered, making it impossible to use the unit.
Do not throw old battery into fire.
≥ Heating a battery or throwing it into a fire may
result in an explosion.
≥ If the operating time is very short even after the
battery has been recharged, the battery has
worn out. Please purchase a new battery.
About the AC adaptor
Be sure to detach the battery after use.
≥ If the battery is left attached, a minute amount
of current continues to flow even if the unit’s
power is off. Keeping the unit in this state may
result in over discharge of the battery. This
may result in you not being able to use the
battery even after it is charged.
≥ If the battery is warm, charging requires more
time than normal.
≥ If the temperature of the battery is extremely
high or extremely low, the CHARGE lamp may
continue flashing, and the battery may not be
charged. Wait until the appropriate
≥ The battery should be stored in the vinyl bag
so metal does not come into contact with the
terminals.
≥ The battery should be stored in a cool place
free from humidity, with as constant
temperature as possible. (Recommended
temperature: 15 °C to 25 °C, Recommended
humidity: 40% to 60%)
≥ Extremely high temperatures or low
temperatures will shorten the life of the battery.
≥ If the battery is kept in high-temperature, high-
humidity, or oily-smoky places, the terminals
may rust and cause malfunctions.
temperature is restored before charging the
battery again. If the battery still fails to charge,
something may be wrong with the battery or
AC adaptor. Contact your dealer.
≥ If you use the AC adaptor near a radio, radio
reception may be disturbed. Keep the AC
adaptor 1 m or more away from the radio.
≥ When using the AC adaptor, it may generate
whirring sounds. However, this is normal.
≥ After use, be sure to disconnect the AC
adaptor. (If it is left connected, a minute
amount of current is consumed.)
≥ Always keep the electrodes of the AC adaptor
and battery clean.
≥ To store the battery for a long period of time,
we recommend you charge it once every year
and store it again after you have completely
used up the charged capacity.
Put this unit near the outlet to make it easy
for the interrupting device (plug) to reach it.
≥ Dust and other matter attached to the battery
terminals should be removed.
97
LSQT1161
Others
is lit), do not remove the SD card, operate the
mode dial, turn off the power or shake or
impact the unit.
About the disc
≥ If there is dust, a scratch, or dirt on disc or
if it is warped, the following phenomena
may occur:
– Block noise in playback image
– Momentary stop of playback image
– Sound interrupted during playback, or
abnormal sound
∫ About the miniSD Card
≥ Be sure to insert miniSD Cards in the
dedicated card adaptor before use. Inserting a
card in this unit without the adaptor may
damage the unit or the card.
≥ Do not insert an empty card adaptor in this
unit. Do not leave the adaptor in this unit while
inserting or removing miniSD Cards. This may
cause the unit to malfunction.
– Scenes are displayed as [
thumbnail display
] on the
– Disc cannot correctly be recognized
– Delay between video and audio
LCD monitor/viewfinder
When the access lamp is illuminated (during
access to the disc), do not open the disc
cover, turn off the power, or cause any
vibrations or impacts.
≥ When the LCD monitor gets dirty, wipe it with a
dry soft cloth.
≥ In a place with drastic temperature changes,
condensation may form on the LCD monitor.
Wipe it with soft dry cloth.
DVD-R/DVD-R DL
≥ For optimum recording on DVD-R discs, this
unit writes control data to a DVD-R used for
recording when it is being inserted and ejected.
If the disc has no area for control data to be
written, recording may not be possible. To
prevent this, do not insert a DVD-R which has
been recorded on more than 50 times.
≥ Do not insert a DVD-R recorded on this unit
that has not been finalized into a recordable
device, such as a DVD recorder. The recorded
data may be damaged.
≥ When the unit has become very cold, for
example due to storage in a cold area, its LCD
monitor will be slightly darker than usual
immediately after the power is turned on. The
normal brightness will be restored when the
unit’s internal temperature rises.
Extremely high precision technology is
employed to produce the LCD Monitor screen
featuring a total of approximately 123,000
pixels. The result is more than 99.99%
effective pixels with a mere 0.01% of the
pixels inactive or always lit. However, this is
not a malfunction and does not affect the
recorded picture.
About the SD card
≥ The memory capacity indicated on the label of
an SD card is the total of the capacity for
copyright protection and management and the
capacity which can be used on the unit, a
computer etc.
≥ During prolonged use, the unit’s surfaces and
the SD card will heat up slightly. This is normal.
≥ Keep the Memory Card out of reach of children
to prevent swallowing.
Extremely high precision technology is
employed to produce the viewfinder screen
featuring a total of approximately 113,000
pixels. The result is more than 99.99%
effective pixels with a mere 0.01% of the
pixels inactive or always lit. However, this is
not a malfunction and does not affect the
recorded picture.
When inserting or removing the SD card,
always set the OFF/ON switch to OFF.
While this unit accesses the SD card (while
/
is being displayed/the access lamp
98
LSQT1161
Others
Explanation of terms
Automatic white balance
About condensation
White balance adjustment recognizes the colour
of light and adjusts so the white colour will
become a purer white. The unit determines the
hue of light that comes through the lens and
white balance sensor, thereby judging the
recording condition, and selects the closest hue
setting.
This is called automatic white balance
adjustment.
However, since the unit only stores white colour
information under several light sources,
automatic white balance adjustment does not
function normally under other light sources.
When condensation forms on the unit, the lens
will cloud up and the unit may not work properly.
Make every effort to ensure that condensation
does not form. If it does form, take the actions
described below.
Causes of condensation
Condensation takes place when the ambient
temperature or humidity is changed as
follows.
≥ When this unit is brought inside from the cold
(e.g. a ski slope) to a warm room.
≥ When this unit is moved from an
air-conditioned car to outside.
≥ When a cold room has been warmed up
quickly.
≥ When cool wind from an air conditioner is
directly blown onto this unit.
2)
10 000K
9
8
000K
000K
3)
7
6
000K
000K
4)
5)
5
4
000K
000K
≥ After summer afternoon showers of rain.
≥ When this unit is in a very humid place where
the air is thick with steam. (e.g. a heated
swimming pool)
6)
1)
7)
3
000K
8)
When this unit is taken to a location with a
significant temperature difference such as
from a cold place to a hot place.
9)
2
1
000K
000K
10)
If, for example, you have used this unit for
recording on a ski slope and are taking it into a
heated room, place the unit inside a plastic bag,
remove as much of the air from inside the bag as
possible, then seal the bag. Leave the unit for
about an hour in the room so the temperature of
the unit is close to the ambient temperature of
the room, then use it.
The illustration above shows the range over
which the auto white balance functions.
1) The effective range of automatic white
balance adjustment on this unit
2) Blue sky
3) Cloudy sky (rain)
4) TV screen
5) Sunlight
6) White fluorescent lamp
7) Halogen light bulb
What to do with the lens is fogged
up.
Remove the battery or AC adaptor and leave the
unit for about 1 hour. When the unit becomes
close to the ambient temperature, the fog
disappears naturally.
8) Incandescent light bulb
9) Sunrise or sunset
10) Candlelight
Outside of the effective range of automatic white
balance adjustment, the image will become
reddish or bluish. Even within the effective range
of automatic white balance adjustment, the
automatic white balance adjustment may not
function properly if there is more than one light
99
LSQT1161
Others
source. For light outside the functional automatic
white balance adjustment range, use the manual
white balance adjustment mode.
Similarly, when recording something on the
opposite side of a road with heavy traffic, a
vehicle that happens to pass by may be brought
into focus.
White balance
Recording a subject that is surrounded by
objects with glossy surfaces or by highly
reflective objects
Since whatever is shiny or glistens is brought into
focus, it is hard to focus on the subject to be
recorded. The focus may become blurry when
recording subjects at the seashore, in night
views or in scenes involving fireworks or special
lights.
The images recorded by the unit may become
bluish or reddish under the influence of certain
light sources. To avoid such phenomena, adjust
the white balance.
White balance adjustment determines the white
colour under different light sources. By
recognizing which is the white colour under
sunlight and which is the white colour under a
fluorescent light, the unit can adjust the balance
among the other colours.
Recording a subject in dark surroundings
The unit cannot focus correctly because the light
information that comes through the lens
decreases considerably.
Since the white colour is the reference for all the
colours (that make up light), the unit can record
pictures in a natural hue if it can recognize the
reference colour white.
Recording a fast-moving subject
As the focus lens-inside moves mechanically, it
cannot keep up with a fast-moving subject.
When, for example, recording a sports event with
fast moving subjects, the focus may lose its
sharpness.
Auto focus
The lens is moved forward or backward
automatically to bring the subject into focus.
Auto focus has the following characteristics.
≥ Adjusts so that the vertical lines of a subject
are seen more clearly.
Recording a subject with little contrast
It is easy to bring subjects with a sharp contrast
or vertical lines or stripes into focus. This means
that a subject with little contrast, such as a white
wall, may become blurry because the unit
achieves focus based upon the vertical lines of
an image.
≥ Attempts to bring an object with higher contrast
into focus.
≥ Focuses on the screen centre only.
Due to these characteristics, auto focus does not
work correctly in the following situations. Record
pictures in the manual focus mode.
Recording distant and close-up objects at the
same time
Since the unit focuses on whatever is at the
centre of the screen, it is difficult to bring the
background into focus when close-up objects are
placed in focus. When recording people with
distant mountains in the background, you cannot
focus on both the subject which is close-up and
the objects which are in the distance.
Recording a subject behind dirty or dusty
window
The subject behind the window will not be
focused because the focus is on the dirty
window.
100
LSQT1161
Others
Specifications
DVD Video Camera
Information for your safety
Power source:
Power consumption:
DC 7.9 V/7.2 V
VDR-D310:
Recording 7.0 W
VDR-D220:
Recording 6.0 W
Signal system
CCIR: 625 lines, 50 fields PAL colour signal
DVD Video Recording format (DVD-RAM, DVD-RW)
DVD-Video format (DVD-RW, DVD-R, DVD-R DL)
Recording format
VDR-D310:
1/6z 3CCD image sensor
Total: 800 Kk3
Effective pixels:
Moving picture: 630 Kk3 (4:3), 540 Kk3 (16:9)
Still picture: 710 Kk3 (4:3), 540 Kk3 (16:9)
VDR-D220:
Image sensor
1/6z CCD image sensor
Total: 800 K
Effective pixels:
Moving picture: 400 K (4:3), 540 K (16:9)
Still picture: 410 K (4:3), 550 K (16:9)
VDR-D310:
Auto Iris, F1.8 to F2.8
Focal length:
3.0 mm to 30.0 mm
Macro (Full range AF)
VDR-D220:
Lens
Auto Iris, F1.8 to F3.7
Focal length:
2.3 mm to 73.6 mm
Macro (Full range AF)
Filter diameter
Zoom
37 mm
VDR-D310:
10k optical zoom, 25/700k digital zoom
VDR-D220:
32k optical zoom, 50/1000k digital zoom
Monitor
2.7z wide LCD monitor (approx. 123 K pixels)
Colour electric viewfinder (approx. 113 K pixels)
Stereo (with a zoom function)
Viewfinder
Microphone
Speaker
1 round speaker ‰ 20 mm
101
LSQT1161
Others
Standard illumination
1,400 lx
12 lx (Low light mode: 1/50)
[approx. 1 lx (VDR-D310)/approx. 2 lx (VDR-D220) with the colour
night view function]
Minimum required
illumination
Video output level
1.0 Vp-p, 75 ™
Y: 1.0 Vp-p, 75 ™
C: 0.3 Vp-p, 75 ™
S Video output level
Audio output level (Line)
Mic input (VDR-D310)
316 mV, 600 ™
Mic sensitivity j50 dB (0 dB=1 V/Pa, 1 kHz)
(‰ 3.5 mm stereo mini jack)
Card reader/writer function (No copyright protection support)
Hi-Speed USB (USB 2.0) compliant
PictBridge-compliant
USB
Dimensions
(excluding the projecting
parts)
66.7 mm (W) k 91.1 mm (H) k 142.7 mm (D)
Mass
(without battery, lens cap
and a disc)
Approx. 510 g
0 °C to 40 °C
(0 °C to 30 °C when connected to the computer)
Operating temperature
Operating humidity
10% to 80%
Motion pictures
Recording media
Compression
8 cm DVD-RAM Ver. 2.1
8 cm DVD-RW Ver. 1.1/2X-SPEED (2X/1X)
8 cm DVD-R for General Ver. 2.0
8 cm DVD-R for DL Ver. 3.0
MPEG2
XP: 10 Mbps (VBR)
(Approx. 18 min recordable time on a single-sided DVD-RAM)
SP: 5 Mbps (VBR)
(Approx. 37 min recordable time on a single-sided DVD-RAM)
LP: 2.5 Mbps (VBR)
Recording mode and
transfer rate
(Approx. 75 min recordable time on a single-sided DVD-RAM)
Audio compression
Still pictures
Dolby Digital, 16 bit (48 kHz/2 ch)
SD Memory Card:
8 MB/16 MB/32 MB/64 MB/128 MB/256 MB/512 MB/1 GB/2 GB
(FAT12 and FAT16 format corresponding)
SDHC Memory Card:
Recording media
4 GB (FAT32 format corresponding)
102
LSQT1161
Others
JPEG (Design rule for Camera File system, based on Exif 2.2
standard), DPOF corresponding
Compression
Picture size
VDR-D310:
2048k1512, 1920k1080 (16:9), 1280k960, 640k480
VDR-D220:
640k480, 640k360 (16:9)
AC adaptor
Information for your safety
Power source:
Power consumption:
DC output:
AC 110 V to 240 V, 50/60 Hz
19 W
DC 7.9 V, 1.4 A (Unit operation)
DC 8.4 V, 0.65 A (Battery charging)
Dimensions
Mass
61 mm (W) k 32 mm (H) k 91 mm (D)
Approx. 110 g
Specifications may change without prior notice.
Number of recordable pictures on an SD card
VDR-D310:
Picture size
3.1M
(2048k1512)
(1920k1080)
2
Picture quality
8 MB
16 MB
32 MB
64 MB
128 MB
256 MB
512 MB
1 GB
3
8
5
13
4
10
24
51
98
7
17
18
29
39
39
61
81
75
120
250
490
990
2010
3950
155
330
650
1290
2630
5170
160
320
630
210
410
820
2 GB
1290
2520
1680
3290
4 GB
103
LSQT1161
Others
Picture size
(1280k960)
(640k480)
0.3M
1
M
Picture quality
8 MB
16 MB
32 MB
64 MB
128 MB
256 MB
512 MB
1 GB
8
21
47
97
14
34
42
97
86
195
75
210
420
155
430
820
870
185
300
1650
3430
6790
13600
27660
54310
390
780
620
1710
3400
6800
13830
27150
1230
2470
5030
9870
1550
3160
6210
2 GB
4 GB
VDR-D220:
Picture size
(640k480)
(640k360)
0.3M
0.2
Picture quality
8 MB
16 MB
32 MB
64 MB
128 MB
256 MB
512 MB
1 GB
42
97
86
195
42
97
86
195
210
430
420
210
430
820
420
870
870
820
1650
3430
6790
13600
27660
54310
1650
3430
6790
13600
27660
54310
1710
3400
6800
13830
27150
1710
3400
6800
2 GB
13830
27150
4 GB
≥ The number of recordable pictures depends on whether [
subject being recorded.
] and [
] are used together and on the
≥ The numbers shown in the table are approximations.
104
LSQT1161
105
LSQT1161
106
LSQT1161
107
LSQT1161
A
LSQT1161 A
F0107Ra0 ( 3000 A )
Matsushita Electric Industrial Co., Ltd.
Web site: http://panasonic.net
|