PYLE Audio PLTCDN7 User Manual

Precautions  
WARNING  
Warning Screen  
While the vehicle is in motion, the monitor only shows "WARNING PICTURE"  
to prevent trafficaccident. Stop the car in a safe location and apply the parking  
break to watch the picture.  
1. Driving on extremely bumpy roads which cause severe vibration may cause the sound to skip.  
2. When the temperature of the unit falls such as during winter, the monitor screen will become  
darker than usual. Normal brightness will return after using the monitor for a while.  
3. This unit uses a precision mechanism. Even in the event that trouble arises, never open  
the case, disassemble the unit, or lubricate the rotating parts. Be sure to consult your supplier.  
4. Any changes or modifications to this product not approved by the supplier could void  
the warranty and will violate FCC approval.  
2
Handling Discs  
Playable Discs  
This product only requires using of 12cm following circular discs.  
DVD-R, DVD-RW, CD-R and CD-RW can be played back, but it depends on the recorded condition.  
Region number(Regional restriction number)  
1 - USA, CANADA  
2 - EUROPE, JAPAN, SOUTH AFRICA, MID EAST ASIA  
3 - KOREA, SOUTH ASIA  
4 - LATIN AMERICA, SOUTH AMERICA, AUSTRALIA, NEW ZELAND  
5 - RUSSIA, INDIA, MONGOLIA, AFRICA  
6 - CHINA  
7 - ALL COUNTRY  
The Region number of this unit is set at your region number.  
DVD players and DVD video discs each have an assigned region number, and if this numbers do not  
match, a disc cannot be played.  
Handling Discs  
*Do not forcibly insert or remove discs.  
*Turn off the power after remove the disc loaded.  
*Do not use discs that have large scratches, are misshappen, cracked, etc.  
When those discs loaded, the monitor shows " Disc Error". In this case, eject the discs.  
No ejecting those discs can damage the unit.  
*Do not touch the recording side of discs by hands. Hold it carefully by the edges  
*Donot expose discs to direct heat from heaters or any heat sources.  
*Do not expose discs to excess humidity or dust.  
*To remove fingermarks and dust, wipe in a straight line from the center of the disc to  
the circumference with soft, well- dried cloth.  
*Do not clean discs surface with solvent, thinner, and other chemicals.  
With the screen open, a driver may not see the disc insertion slot. For your safety,  
insert a disc with the screen closed.  
3
Operating with the main unit  
Number  
1. VOLUME  
2. VOLUME  
3. MODE  
POWER  
4.OPEN/CLOSE  
5. JOG  
6. JOG  
7. JOG  
8. JOG  
Radio  
TV  
DVD/CD  
Volume Down  
Volume Up  
Short Key: Mode/Power On  
Long Key: Powe Off  
Monitor Open/Close  
Ch Seek Up  
Upper  
Downward  
To the Left  
To the Right  
Enter  
Ch Seek Down  
Ch Tune Down  
Ch Tune Up  
Band  
Mute  
Setting Sounds  
Preset 1  
9. JOG Center  
10. MUTE  
11. FUNC  
12. Preset 1  
Track/Chapter/Fast Forward  
Track/Chapter/Fast Forward  
Repeat  
13. Preset 2  
Preset 2  
Preset 3  
Preset 4  
Preset 5  
Preset 6  
14. Preset 3  
RPT  
15. Preset 4  
RDM  
16. Preset 5  
SUB-T  
17. Preset 6  
AUDIO  
Random  
Sub Title  
Audio  
18. Eject  
Disc Eject  
Remote Sensor  
Reset  
19. R/Sensor  
20. Reset  
21. PS/AS  
22. ASPECT  
23. SLIDE  
Preset Scan/Auto Store  
Aspect  
Sliding Monitor  
4
Operating with the Remote Control  
REMOTE CONTROLLER KEY FUNCTION  
Number  
1
2
Radio  
TV  
CDC  
DVD/CD  
POWER ON/OFF  
OPEN/CLOSE  
MODE  
3
4
MUTE  
5
6
Auto Store/Preset Scan  
Function  
7
ASPECT  
8 -  
Preset 1  
Preset 2  
Preset 3  
Preset 4  
Preset 5  
Preset 6  
Ch No  
Ch No  
Ch No  
Ch No  
Ch No  
Ch No  
Ch No  
Ch No  
Ch No  
Ch No  
Intro  
Random  
Disc Up  
Disc Down  
Figure.10  
Clear  
9
10  
11  
Volume Up/Down  
TILT Up/Down  
12 -I  
Track/Chapter Down  
Track/Chapter Up  
Fast Backward  
Fast Forward  
Pause/Play  
STEP  
13 -  
14 -  
15 -  
16 - II  
17  
I
18  
19 -  
DISPLAY  
Upper  
Ch Seek Up  
Ch Seek Down  
Ch Tune Down  
Ch Tune Up  
Band  
Downward  
To the Left  
To the Right  
Enter/Play  
TITLE  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
SUB-TITLE  
AUDIO  
REPEAT  
SLOW  
ZOOM  
A-B  
STEP  
RANDOM  
PROGRAM  
SEARCH  
DVD SETUP  
Replacing the battery for the remote control  
1.Slide and hold the hooker (®Á in the figure) of the battery cover to  
in the direction of the arrow  
2. Slide the battery cover downward hoding the hooker in the direction  
of the arrow.  
3.insert the battery (CR2025 3V) with O+ face up.  
4.Close the battery cover.  
*Do not use metal tweezers to hold the battery to prevent short-circuit.  
*Dispose of spent batteries in compliance with all applicable regulation.  
5
Basic Operations  
Resetting  
*In case the unit does not operate normally, press the [RESET] button with  
a pointed object to restart the operation when the power of the unit is on.  
*Pressing the [RESET] button will turn off the power. Press the [MODE/POWER]  
button to turn power on.  
*When the screen shows touch key [RADIO] on another mode, change the mode  
to radio mode and then return to the original mode.  
Turning On the Power  
Press the [MODE/POWER] button shortly to switch on the unit,  
When the power of the unit is off, pressing the [OPEN/CLOSE] button will turn on  
the power and the monitor will automatically open.  
Turning Off the Power  
Press the [MODE/POWER] button for more than 2 seconds again to switch off the unit.  
*When the monitor is open, pressing the [OPEN/CLOSE] button will close  
the monitor and video is off, but sound is still working.  
*When the monitor is open, pulling out the car key (ACC OFF) will turn off  
the power and close monitor automatically.  
Selecting a Mode  
1.Press the [MODE/POWER] button shortly to change the mode of operation.  
2.Each time this button is pressed, the mode switches in the following order  
RADIO -> CDC (DVDC) -> DVD -> TV -> NAVI -> AV1 -> AV2 -> RVC -> RADIO  
*[OFF] or [NONE] for set up CDC, AV1, AV2, RVC is selected, thoes modes do not appear on the monitor .  
Adjusting the Volume  
Press the Volume [ ] or [ ] button on any mode to adjust the volume.  
The volume level is indicated in the monitor from 0 (minimum) to 50 (maximum).  
While driving, Keep the volume level at which external sounds can be heard.  
Mute On/Off  
Each time the [MUTE] button is pressed, mute is turned on and off.  
Opening the Monitor  
Press the [OPEN/CLOSE] button. The monitor comes out and stand up automatically.  
*When the unit is off, pressing the [OPEN/CLOSE] button will turn on the power and  
the monitor will be automatically opened.  
*If the monitor touches an obstacle while it is opening or closimg, the monitor  
will stop moving or close. Close the monitor after removing the obstacle.  
*Do not touch the monitor when it is opening or closing. Doing so may damage the unit.  
*To prevent the battery from going dead, operate this unit with the engine running.  
6
iˆšŠGv—Œ™ˆ›–•š͑͑  
j“–š•ŽG›ŒGt–•›–™G  
΁ΣΖΤΤ͑ΥΙΖ͑[OPEN/CLOSE] ͑ΓΦΥΥΠΟ͑ΒΘΒΚΟ͑ΥΠ͑ΙΠΦΤΖ͑ΥΙΖ͑ΞΠΟΚΥΠΣ͟  
!
jˆœ›–•  
*The monitor can be closed only when it is positioned parallel with the front  
of unit. Position manually the monitor parallel with the front of unit by holding  
left and right side of the monitor with hands and then press the [OPEN/CLOSE]  
button to close it.  
*When a picture displays on the monitor, pressing the [OPEN/CLOSE] button  
will close the monitor. But the sound can still be heard. If you want to turn off  
the sound, press the [MODE/POWER] button more than 2 seconds to turn off  
the power and the sound.  
h‹‘œš›•ŽG›ŒGz“‹ŒGw–š›–•G  
͢͟΁ΣΖΤΤ͑ΥΙΖ [SLIDE] ΓΦΥΥΠΟ͟  
ͣ͟ͶΒΔΙ͑ΥΚΞΖ͑ΥΙΖ͑[SLIDE] ͑ΓΦΥΥΠΟ͑ΚΤ͑ΡΣΖΤΤΖΕ͑͝ΥΙΖ͑ΞΠΟΚΥΠΣ͑ΤΝΚΕΖΤ͑ΗΠΣΨΒΣΕ͑ΠΣ͑ΓΒΔΜΨΒΣΕ͑͑͢ΤΥΖΡ͝  
͑͑ΥΠΥΒΝ͑ͣ͑ΤΥΖΡΤ͑ΨΚΥΙ͑ͤ͑ΡΠΤΚΥΚΠΟΤ͑͟΅ΙΖ͑ΒΕΛΦΤΥΖΕ͑ΡΠΤΚΥΚΠΟ͑ΚΤ͑ΤΥΠΣΖΕ͑ΚΟ͑ΞΖΞΠΣΪ͟  
h‹‘œš›•ŽG›ŒGsˆ›Œ™ˆ“G}Œž•ŽGh•Ž“ŒG  
΅ΙΖ͑ΞΠΟΚΥΠΣ͘Τ͑ΝΖΗΥ͠ΣΚΘΙΥ͑ΧΚΖΨΚΟΘ͑ΒΟΘΝΖ͑ΔΒΟ͑ΓΖ͑ΒΕΛΦΤΥΖΕ͑ΞΒΟΦΒΝΝΪ͑ΒΤ͑ΥΙΖ͑ΡΚΔΥΦΣΖ͑ΓΖΝΠΨ͟  
h‹‘œš›G›ŒGˆ•Ž“ŒG”ˆ•œˆ““ G‰ G–“‹•ŽG‰–›G“Œ›Gˆ•‹G™Ž›Gš‹ŒG–G›ŒG”–•›–™G  
ž›Gˆ•‹šGˆšG›ŒG—Š›œ™ŒUG  
h‹‘œš›•ŽG›ŒGwŠ›œ™ŒGt–‹ŒGOhš—ŒŠ›P  
ͶΒΔΙ͑ΥΚΞΖ͑ΥΙΖ͑[ASPECT] ΓΦΥΥΠΟ͑ΚΤ͑ΡΣΖΤΤΖΕ͑͝ΥΙΖ͑ΡΚΔΥΦΣΖ͑ΞΠΕΖ͑ΔΙΒΟΘΖΤ͑ΚΟ͑ΗΠΝΝΠΨΚΟΘ͑ΠΣΕΖΣ͟  
FULL -> WIDE -> NORMAL -> FULL  
[FULL]: ͑΀ΣΚΘΚΟΒΝ͑ͥͫͤ͑ΡΚΔΥΦΣΖ͑ΚΤ͑ΖΩΡΒΟΕΖΕ͑ΤΚΕΖΨΒΪΤ͑ΥΠ͑ΗΚΝΝ͑ΥΙΖ͑ΤΔΣΖΖΟ͟  
͑͑͑͑͑͑͑͑͑͑͑͑͑΅ΠΡ͑ΒΟΕ͑ΓΠΥΥΠΞ͑ΠΗ͑ΥΙΖ͑ΡΚΔΥΦΣΖ͑ΒΣΖ͑Τ΢ΦΒΤΙΖΕ͟  
[WIDE]: v•“ G™Ž›Gˆ•‹G“Œ›G—–™›–•šG–G–™Ž•ˆ“G[aZG—Š›œ™ŒGˆ™ŒGŒŸ—ˆ•‹Œ‹Gš‹Œžˆ šU  
[NORMAL]: Gv™Ž•ˆ“G—Š›œ™ŒGž›G[aZGˆš—ŒŠ›G™ˆ›–U  
QG{ŒGˆŠ›–™ G‹Œˆœ“›GšŒ››•ŽGš [NORMAL] U  
h‹‘œš›•ŽG›ŒGiˆššGsŒŒ“  
͢͟΁ΣΖΤΤ͑ΥΙΖ͑ [FUNC] ΓΦΥΥΠΟ͑ΣΖΡΖΒΥΖΕΝΪ͑ΦΟΥΚΝ [BASS]͑ΚΤ͑ΤΖΝΖΔΥΖΕ͟  
ͣ͟΁ΣΖΤΤ͑ΥΙΖ͑ }vs|tlG‚ඖ„GΓΦΥΥΠΟ͑ ΥΠ͑ΚΟΔΣΖΒΤΖ͑ΥΙΖ͑ΓΒΤΤ͑ΝΖΧΖΝ͟  
ͤ͟΁ΣΖΤΤ͑ΥΙΖ͑ }vs|tlG‚ඔ„GΓΦΥΥΠΟ͑ ΥΠ͑ΕΖΔΣΖΒΤΖ͑ΥΙΖ͑ΓΒΤΤ͑ΝΖΧΖΝ͟  
h‹‘œš›•ŽG›ŒG{™Œ‰“ŒGsŒŒ“  
͢͟΁ΣΖΤΤ͑ΥΙΖ͑ [FUNC] ΓΦΥΥΠΟ͑ΣΖΡΖΒΥΖΕΝΪ͑ΦΟΥΚΝ [TREBLE]͑ΚΤ͑ΤΖΝΖΔΥΖΕ͟  
ͣ͟΁ΣΖΤΤ͑ΥΙΖ͑ }vs|tlG‚ඖ„GΓΦΥΥΠΟ͑ ΥΠ͑ΚΟΔΣΖΒΤΖ͑ΥΙΖ͑ΥΣΖΓΝΖ͑ΝΖΧΖΝ͟  
ͤ͟΁ΣΖΤΤ͑ΥΙΖ͑ }vs|tlG‚ඔ„GΓΦΥΥΠΟ ͑ΥΠ͑ΕΖΔΣΖΒΤΖ͑ΥΙΖ͑ΥΣΖΓΝΖ͑ΝΖΧΖΝ͟  
h‹‘œš›•ŽG›ŒGiˆ“ˆ•ŠŒGsŒŒ“  
͢͟΁ΣΖΤΤ͑ΥΙΖ͑ [FUNC] ΓΦΥΥΠΟ͑ΣΖΡΖΒΥΖΕΝΪ͑ΦΟΥΚΝ [BALANCE]͑ΚΤ͑ΤΖΝΖΔΥΖΕ͟  
ͣ͟΁ΣΖΤΤ͑ΥΙΖ͑ }vs|tlG‚ඖ͑ΓΦΥΥΠΟ͑ΥΠ͑ΖΞΡΙΒΤΚΫΖ͑ΥΙΖ͑ΣΚΘΙΥ͑ΔΙΒΟΟΖΝ͟  
ͤ͟΁ΣΖΤΤ͑ΥΙΖ͑ }vs|tlG‚ඔ͑ΓΦΥΥΠΟ͑ΥΠ͑ΖΞΡΙΒΤΚΫΖ͑ΥΙΖ͑ΝΖΗΥ͑ΔΙΒΟΟΖΝ͟  
h‹‘œš›•ŽG›ŒGmˆ‹Œ™GsŒŒ“  
͢͟΁ΣΖΤΤ͑ΥΙΖ͑ [FUNC] ΓΦΥΥΠΟ͑ΣΖΡΖΒΥΖΕΝΪ͑ΦΟΥΚΝ͑[FADER]͑ΚΤ͑ΤΖΝΖ͑ΔΥΖΕ͟  
ͣ͟΁ΣΖΤΤ͑ΥΙΖ͑ }vs|tlG‚ඖ͑ΓΦΥΥΠΟ͑ΥΠ͑ΖΞΡΙΒΤΚΫΖ͑ΥΙΖ͑ΗΣΠΟΥ͑ΔΙΒΟΟΖΝ͟  
ͤ͟΁ΣΖΤΤ͑ΥΙΖ͑ }vs|tlG‚ඔ͑ΓΦΥΥΠΟ͑ΥΠ͑ΖΞΡΙΒΤΚΫΖ͑ΥΙΖ͑ΝΖΗΥ͑ΔΙΒΟΟΖΝ͟  
7
Radio Operation  
Press the [MODE/POWER] button repeatedly until radio mode is selected.  
In case the radio is tuned over 3 hours wih closing the monitor, The unit will be hotter.  
Please make sure to open the monitor when you want to listen to radio over 2 hours,  
or else the unit may be damaged.  
Selecting Radio Reception Area  
See "Selecting Radio Reception Area" in page 12.  
Selecting the Radio Band  
1. Press the [MODE/POWER] button repeatedly until the radio mode is selected.  
Both the sub LCD and the monitor displays information on the radio station tuned in.  
2. Press the [ENTER ] button to selct the desired radio band. Each time the [ENTER]  
button is pressed, the radio band switches in following order.  
FM1 -> FM2 -> FM3 -> AM1 -> AM2 ->FM1  
Seek Tuning  
Push the JOG [ ] or [ ] button to automaticaly seek a station.  
Tuning automatically stops at a broadcasting frequency.  
Manual Tuning  
Push the JOG [ ] or [ ] button repeatedly until the desired station is selected.  
The frequecy changes one step at a time.  
Manual Memory  
1. Tune in the station to be preset with seek or manual tuning.  
2. Press one of the [PRESET] buttons for more than 2 seconds at which you want  
to store the selected station.  
3. Each band can store 6 stations in the [PRESET] buttons as follows.  
FM1: 6, FM2: 6, FM3: 6, AM1: 6, AM2: 6, Total: 30staions  
Auto Memory  
1. Press the [ENTER] button to select the band for the stations to be preset.  
2. Press the [PS/AS] button for more than 2 seconds. Stations are automatically  
stored in the [PRESET] buttons in order of signal strength.  
3. Each band can store 6 stations in the [PRESET] buttons as follows.  
Preset Scan  
This function is useful when searching the stations stored in each [PRESET] buttons.  
1. Press the [PS/AS] button shortly. The unit starts scanning each station for 5 seconds sequentially  
2. Press the [PS/AS] button shortly again to stop scanning and retain the station currently selected.  
Recalling the Preset Station  
Press one of the [PRESET] button which the desired station is preset .  
8
Basic Operations with Touch Keys  
This unit has Touch Screen feature. You can select/adjust the functions by touchung touch keys  
displaying on the monitor.  
You can touch the screen with finger or the plastic pen supplied with this unit.  
1. Press the [OPEN/CLOSE] button to open the monitor and turn on the power.  
2. Touch anywhere of the screen softly with a finger to show the menu of touch keys.  
BASiC MODE  
1. [MODE] key  
2. Current mode display  
3. [EQ/DSP] key  
4. [SETUP] key  
5. [PICTURE] key  
6. [EXIT] Key  
7. [TILT] Up/Down key  
Selecting the Mode  
1. Touch [MODE] to show the menu of each mode on the screen  
2. Touch one of the mode key that you want.  
Adjusting Sound Volume  
Touch VOL [ ] or [ ] to adjust the volume of the sound.  
The adjusted sound volume is stored in memory.  
Adjusting Tilt Angle  
Touch TILT [ ] or [ ] to adjust vertical angle of the monitor.  
The adjusted angle is stored in memory.  
Removing the menu on the screen  
Touch [EXIT] to exit from the menu on the screen, or else the menu will disappear within 10 seconds.  
Touch Point Calibration  
The touch point may be moved a little after long using of the unit.  
In this case, reset the touch point as follows  
1. Press [FUNC] button of the main unit for more than 10 seconds. The monitor shows following picture .  
2. Press the center of cross mark on the left upper side with a plastic pen with a rounded end.  
The cross mark disappears and appears again on the right upper side.  
3. Press the center of cross mark on the right upper side. The cross mark disappears  
and appears again on the left bottom.  
4. Press the center of cross mark on the left bottom side. The cross mark disappears  
and appears again on the right bottom.  
5. Press the center of cross mark on the right bootom side. The cross mark disappears  
and appears. The correct touch point is set up.  
9
System Settings with Touch Keys  
Adjusting the Bass Level  
1. Touch [EQ/DSP] to show the audio menu.  
2. Touch [ ] or [ ] to decrease or increase the bass level.  
Adjusting the Treble Level  
1. Touch [EQ/DSP] to show the menu.  
2. Touch [ ] or [ ] to decrease or increase the treble level.  
Adjusting the Balance Levels  
1. Touch [EQ/DSP] to show the menu.  
2. Touch [ ] or [ ] to emphasize the sound in the left or the right channel.  
Adjusting the Fader Levels  
1. Touch [EQ/DSP] to show the menu.  
2. Touch [ ] or [ ] to emphasize the sound in the front or the rear channel.  
Selecting EQ  
1. Touch [EQ/DSP] to show the menu.  
2. Touch [EQ] to select one of EQ mode  
Each time [EQ] is touched, the EQ mode switches as follows.  
OFF -> CLASSIC -> ROCK -> POPS -> JAZZ -> OFF  
Setting Up 3D Sound  
1. Touch [EQ/DSP] to show the menu.  
2. Touch [3D] to select 3D sound [ON] or [OFF].  
[ON]: 3D sound on  
[OFF]: 3D sound off  
Setting Up 4.1 Channel Output  
1. Touch [EQ/DSP] to show the menu.  
2. Touch [4.1 Ch] to select 4.1 channel [ON] or [OFF].  
[ON]: 4.1 Ch on  
[OFF]: 4.1 Ch off  
Setting Up A/V 1 or A/V 2 Input  
1. Touch [SETUP] and then Touch [EXT. DEVICE] to show the menu.  
2. Touch [AV 1] or [AV 2] to select [ON] or [OFF].  
Each time [AV 1] or [AV 2] is touched, [ON] or [OFF] is selected.  
3. Select [ON] when a external device is connected to [AV 1] or [AV 2].  
Select [OFF] when no external device is connected to [AV 1] or [AV 2].  
*When a navigation unit is connected to AV 1 or AV 2 input, make sure to set  
[OFF] for AV 1 or AV 2 which it is connected to.  
10  
System Settings with Touch Keys  
Setting Clock  
1. Touch [SETUP] and then Touch [SYSTEM] to show the menu.  
2. Touch HOUR [ ] or [ ] to adjust the hour.  
3. Touch MIN [ ] or [ ] to adjust the minute.  
* The screen dispalys 24 hours and sub LCD dispalys 12 hours.  
* Clock on the sub LCD displays only when the power of the unit is off and ACC on.  
Adjusting the Volume of Subwoofer  
1. Touch [SETUP] and then Touch [VOLUME] to show the menu.  
2. Touch Woofer VOL [ ] or [ ] to adjust the subwoofer volume.  
Adjusting the Brightness of Picture  
1. Touch [PICTURE] to show the picture menu.  
2. Touch BRIGHT [ ] or [ ] to adjust the brightness of picture.  
Adjusting the Color Density of Picture  
1. Touch [PICTURE] to show the menu.  
2. Touch COLOR [ ] or [ ] to adjust the color density of picture.  
Adjusting the Tint of Picture  
1. Touch [PICTURE] to show the menu.  
2. Touch HUE [ ] or [ ] to adjust the tint of picture.  
Selecting the Brightness of Backlight  
1. Touch [PICTURE] to show the menu.  
2. Touch [DIMMER] to select the brightness of backlight.  
Each time [DIMMER] is touched, the menu switches as follows.  
USER -> STD -> DAY -> NIGHT -> AUTO -> USER  
[USER] : To adjust the dimmer level by end user  
[STD] : Standard level of the dimmer adjusted by the factory  
[DAY] : Recommended when the surrouding is very bright.  
[NIGHT] : Recommended for night time or dark surrounding.  
[AUTO] : Automatically adjusted according to the surroundung brightness.  
11  
Radio Operation with Touch Keys  
1. Touch softly with finger anywhere of the screen to show touch key menu.  
2. Touch [MODE] to show the mode menu and then touch [RADIO] to select radio mode.  
Selecting Radio Reception Area  
1. Touch [SETUP] and then Touch [SYSTEM] to show the menu.  
2. Touch [RADIO AREA] to select radio area for your country.  
USA  
USA, Canada, S.America  
EU, S/E Asia, M/E Asia, Africa  
Korea, Taiwan, Philipine  
China  
EUROPE  
KOREA  
CHINA  
Selecting the Radio Band  
Touch [BAND] to select radio band.  
Each time [BAND] is touched, the radio band switches in following order.  
FM1 -> FM2 -> FM3 -> AM1 -> AM2 ->FM1  
Seek Tuning  
Touch [ ] or [ ] to automaticaly seek a radio station.  
Tuning automatically stops at a broadcasting frequency.  
Manual Tuning  
Touch [ ] or [ ] repeatedly until the desired station is selected.  
The frequecy changes one step at a time.  
Manual Preset Memory  
1. Tune in the station to be preset with seek or manual tuning.  
2. Touch one of the preset [CH1 - CH6] for more than 2 seconds at which you want to store  
the selected station.  
3. Each band can store 6 stations.  
FM1: 6, FM2: 6, FM3: 6, AM1: 6, AM2: 6, Total: 30staions  
Auto Preset Memory  
1. Touch [BAND] to select the band for the stations to be preset.  
2. Touch [AS] to store the stations automatically. The stations will be automatically  
stored in the [PRESET] buttons in order of signal strength.  
Preset Scan  
The frequency of the stations stored in the preset [CH1 - CH6] is being displayed on the screen.  
1. Touch [PS] shortly. The unit starts scanning each station for 5 seconds sequentially.  
2. Touch [PS] shortly to stop scanning and retain the station currently selected.  
Recalling the Preset Station  
1. Touch [BAND] to select the desired band.  
2. Touch one of preset [CH1 - CH6] shortly at which the desired station is preset.  
Cautions  
In case the radio is worked over 3 hours without opening the monitor, The unit  
becomes hotter. It is strongly recommended to open the monitor when you want  
to listen to radio over 3 hours, or else the unit can be damaged.  
12  
{}Gv—Œ™ˆ›–•Gž›G{–œŠGrŒ  
͑
zŒ“ŒŠ›•ŽGG}‹Œ–Gz š›Œ”  
͢͟΅ΠΦΔΙ͑[SETUP] ΒΟΕ͑ΥΙΖΟ͑΅ΠΦΔΙ͑[SYSTEM] ͑ΥΠ͑ΤΙΠΨ͑ΥΙΖ͑ΞΖΟΦ͟  
ͣ͟΅ΠΦΔΙ͑[VIDEO STD] ͑͑ΥΠ͑ΤΖΝΖΔΥ͑΅·͑ΤΪΤΥΖΞ͑ΗΠΣ͑ΪΠΦΣ͑ΔΠΦΟΥΣΪ͟  
͑͑͑ͶΒΔΙ͑ΥΚΞΖ͑[VIDEO STD] ΚΤ͑ΥΠΦΔΙΖΕ͑͝ΥΙΖ͑΅·͑ΤΪΤΥΖΞ͑ΚΤ͑ΤΨΚΥΔΙΖΕ͟  
NTSC -> PAL BG -> PAL DK -> PAL I -> PAL AUS -> NTSC  
ͤ͟΅ΠΦΔΙ͑‚vr„G͑›–Gš›–™ŒG›ŒG{}Gš š›Œ”G –œGšŒ“ŒŠ›Œ‹U  
<TV System for Your Country>  
NTSC  
Ά΄Ͳ͑͝ʹΒΟΒΕΒ͑͝;ΖΩΚΔΠ͑͝ʹΙΚΝΖ͑͝·ΖΟΖΫΦΖΝΒ͑͟΅ΒΚΨΒΟ͑͝ͼΠΣΖΒ͑  
͸ΖΣΞΒΟΪ͑͝ͺΥΒΝΪ͑͟΄ΡΒΚΟ͑͝΄ΨΚΥΫΖΣΝΒΟΕ͑͝΄ΨΖΕΖΟ͑͝ͿΖΥΙΖΣΝΒΟΕΤ  
΅ΦΣΜΖΪ͑͝;͠Ͷ͑ͲΤΚΒ͑͝΄͠Ͷ͑ͲΤΚΒ  
PAL BG  
PAL I  
Άͼ͑͝͹ͼ͑͝΄͠ͲΗΣΚΔΒ͑͝  
PAL DK  
ʹΙΚΟΒ͑͝΁ΠΝΒΟΕ  
PAL AUS ͲΦΤΥΣΒΝΚΒ  
~ˆ›Š•ŽG{}  
͑͢͟΅ΠΦΔΙ͑[MODE] ͑ΜΖΪ͑͑ΥΠ͑ΤΙΠΨ͑ΥΙΖ͑ΞΠΕΖ͑ΞΖΟΦ͑ΒΟΕ͑ΥΙΖΟ͑ΥΠΦΔΙ͑[TV] ͑ΥΠ͑ΤΖΝΖΔΥ͑΅·͑ΞΠΕΖ͟  
ͣ͑͟΅ΠΦΔΙ͑[BAND] ͑ΥΠ͑ΤΖΝΖΔΥ͑ΥΙΖ͑ΕΖΤΚΣΖΕ͑ΓΒΟΕ͟  
͑͑͑͑ͶΒΔΙ͑ΥΚΞΖ͑[BAND] ͑ΚΤ͑ΥΠΦΔΙΖΕ͑͝ΥΙΖ͑΅·͑ΓΒΟΕ͑ΤΨΚΥΔΙΖΤ͑ΚΟ͑ΗΠΝΝΠΨΚΟΘ͑ΠΣΕΖΣ  
TV1 -> TV2 -> TV3 -> TV1  
ͤ͟΅ΠΦΔΙ͑ΠΟΖ͑ΠΗ͑͑΁΃Ͷ΄Ͷ΅ [1-36] ͑ΨΙΚΔΙ͑ΚΤ͑ΡΣΖΤΖΥ͑ΥΙΖ͑ΕΖΤΚΣΖΕ͑ΤΥΒΥΚΠΟ͟  
hœ›–Gz›–™Œ  
͢͟΅ΠΦΔΙ͑[BAND] ͑ΥΠ͑ΤΖΝΖΔΥ͑ΥΙΖ͑ΕΖΤΚΣΖΕ͑ΓΒΟΕ͟  
ͣ͟΅ΠΦΔΙ͑[AS] ͑ΥΠ͑ΒΦΥΠ͑ΤΔΒΟ͑ΒΟΕ͑ΤΥΠΣΖ͑΅·͑ΔΙΒΟΟΖΝΤ͟  
͑͑ͲΝΝ͑ΣΖΔΖΚΧΒΓΝΖ͑΅·͑ΔΙΒΟΟΖΝΤ͑ΒΣΖ͑ΒΦΥΠΞΒΥΚΔΒΝΝΪ͑ΤΥΠΣΖΕ͑ΚΟ͑ΖΒΔΙ͑΅·͑ΓΒΟΕ͑͟  
͑͑΅ΙΖ͑ͤͧ͑ΤΥΒΥΚΠΟΤ͑ΨΚΥΙ͑ΘΠΠΕ͑ΣΖΔΖΡΥΚΠΟ͑ΒΣΖ͑ΤΥΠΣΖΕ͑ΚΟ͑ΡΣΖΤΖΥ͑ΠΟ͑ΖΒΔΙ͑ΓΒΟΕ͟  
tˆ•œˆ“G{œ••ŽGˆ•‹Gz›–™ŒGG  
͢͟΅ΠΦΔΙ͑[BAND] ͑ΥΠ͑ΤΖΝΖΔΥ͑ΥΙΖ͑ΕΖΤΚΣΖΕ͑ΓΒΟΕ͟  
ͣ͟΅ΠΦΔΙ͑‚ඔ„G–™G‚ඖ„͑ΗΠΣ͑ΞΒΟΦΒΝ͑ΥΦΟΚΟΘ͑ΒΟΕ͑‚̵„G–™G‚̷„͑ΗΠΣ͑ΒΦΥΠ͑ΤΖΖΜ͑ΥΦΟΚΟΘ͟  
ͤ͟΅ΠΦΔΙ͑ΠΟΖ͑ΠΗ͑͑΁΃Ͷ΄Ͷ΅ [1-36] ͑ΥΠ͑ΤΥΠΣΖ͑ΥΙΖ͑ΤΖΝΖΔΥΖΕ͑ΤΥΒΥΚΠΟ͟  
jˆœ›–•  
͛͑ͷΠΣ͑ΪΠΦΣ͑ΤΒΗΖΥΪ͑͝ΥΙΚΤ͑ΦΟΚΥ͑ΥΦΣΟΤ͑ΠΗΗ͑ΥΙΖ͑ΡΚΔΥΦΣΖ͑ΨΙΖΟ͑ΥΙΖ͑ΔΒΣ͑ΚΤ͑ΞΠΧΚΟΘ͑͟΀ΟΝΪ͑ΥΙΖ͑ΒΦΕΚΠ͑ΔΒΟ͑  
͑͑ΓΖ͑ΙΖΒΣΕ͑͟΅ΙΖ͑ΡΚΔΥΦΣΖ͑ΔΒΟ͑ΠΟΝΪ͑ΓΖ͑ΨΒΥΔΙΖΕ͑ΨΙΖΟ͑ΥΙΖ͑ΡΒΣΜΚΟΘ͑ΓΣΖΒΜ͑ΚΤ͑ΒΡΡΝΚΖΕ͟  
͑͑΄ΥΠΡ͑ΥΙΖ͑ΧΖΙΚΔΝΖ͑ΚΟ͑Β͑ΤΒΗΖ͑ΝΠΔΒΥΚΠΟ͑ΒΟΕ͑ΒΡΡΝΪ͑͑ΥΙΖ͑ΡΒΣΜΚΟΘ͑ΓΣΖΒΜ͑ΥΠ͑ΨΒΥΔΙ͑ΥΙΖ͑ΡΚΔΥΦΣΖ͟  
u–›Œš  
͛͑ΈΙΖΟ͑ΣΖΔΖΚΧΚΟΘ͑ΥΙΖ͑΅·͑ΓΣΠΒΕΔΒΤΥΤ͑͝ΥΙΖ͑ΤΥΣΖΟΘΥΙ͑ΠΗ͑ΥΙΖ͑ΤΚΘΟΒΝΤ͑ΔΙΒΟΘΖΤ͑ΤΚΟΔΖ͑ΥΙΖ͑ΔΒΣ͑ΚΤ͑ΞΠΧΚΟΘ͑͝  
͑͑͑ΤΠ͑ΚΟ͑ΤΠΞΖ͑ΔΒΤΖΤ͑ΚΥ͑ΞΒΪ͑ΟΠΥ͑ΓΖ͑ΡΠΤΤΚΓΝΖ͑ΥΠ͑ΣΖΔΖΚΧΖ͑ΔΝΖΒΣ͑ΡΚΔΥΦΣΖΤ͟  
͛͑΅·͑ΤΚΘΟΒΝΤ͑ΒΣΖ͑ΤΥΣΠΟΘΝΪ͑ΝΚΟΖΒΣ͑͝ΤΠ͑ΣΖΔΖΡΥΚΠΟ͑ΚΤ͑ΒΗΗΖΔΥΖΕ͑ΓΪ͑ΓΦΚΝΕΚΟΘΤ͑͝ΞΠΦΟΥΒΚΟΤ͑ΒΟΕ͑ΠΥΙΖΣ͑ΠΓΤΥΒΔΝΖΤ͟  
͛͑΄ΦΔΙ͑ΖΩΥΖΣΟΒΝ͑ΗΒΔΥΠΣΤ͑ΤΦΔΙ͑ΒΤ͑ΖΝΖΔΥΣΚΔ͑ΥΣΒΚΟ͑ΝΚΟΖΤ͑͝Β͑ΙΚΘΙ͑ΧΠΝΥΒΘΖ͑ΝΚΟΖΤ͑͝ΒΟΕ͑ΤΚΘΟΒΝ͑ΕΖΧΚΔΖΤ͑ΞΒΪ͑  
͑͑͑͑ΕΚΤΥΦΣΓ͑ΥΙΖ͑ΡΚΔΥΦΣΖ͑ΠΣ͑ΔΒΦΤΖ͑ΟΠΚΤΖ͟  
͛͑ͺΗ͑ΥΙΖ͑ΣΖΔΖΡΥΚΠΟ͑ΚΤ͑ΡΠΠΣ͑͝ΤΨΚΥΔΙ͑ΥΠ͑Β͑ΤΥΒΥΚΠΟ͑ΨΚΥΙ͑ΘΠΠΕ͑ΣΖΔΖΡΥΚΠΟ͟  
13  
DVD/CD Changer Operation with Touch Keys  
Setting Up a DVD/CD Changer  
1. Touch [SETUP] and then Touch [EXT. DEVICE] to show the menu.  
2. Touch [CDC] to select DVD or CD changer source.  
Each time [CDC] is touched, the source is switched as follows.  
NONE -> MPIRE -> DVDC 12 -> DVDC 10 -> S CDC -> CDC 6 -> NONE  
3. Select [6 CDC], [10 DVDC] or [12 DVDC] when it is connected to the AV control box.  
Select [S CDC] when Sanyo 6 CD changer is connected to the AV control box.  
Select [NONE] when no DVD or CD changer is connected to the AV control box.  
*The factory default setting is [NONE].  
*The car DVD or CD changer is an optional item. This unit only offers input for the system.  
*Only when 6 disc CD changer, 10 or 12 disc DVD changers which we are supplying is  
connected, all the functions are working as mentioned in here.  
*To control of the 10 or 12 DVD changer, see the owner's manual of the DVD changer.  
Operating the10/12 DVD Changer or the 6 CD Changer  
Touch [MODE] key and then touch [CDC] key to select CD/DVD changer mode.  
STATUS: This shows the current CD status (Disc check, Seek, Etc).  
TIME: This shows playing time of the disc being played.  
Selecting a Disc  
Touch [ ] or [ ] button to select "DISC".  
Pausing Disc Play  
Touch [ II] to pause playback. Touch [ II] again to resume playback.  
Stopping Disc Play  
Touch [ ] to stop playback. Touch [ II] to resume playback.  
Fast Forward Play  
Touch [  
] for fast forward.  
Fast Backward play  
Touch [  
] for fast backward.  
Track/Chapter Search  
Touch [I  
] or [  
I] to search the track/chapter number of the current disc.  
Repeat Play  
Touch [RPT] to select [ONE]. [ALL] or [OFF]  
[ALL] : All the track on the current disc plays repeatedly  
[ONE] :The selected track on the current disc plays repeatedly.  
[OFF] : Repeat play will be off.  
Intro Play  
Touch [INT] to select [ONE]. [ALL] or [OFF]  
[ALL] : The first 10 seconds of each track of all discs plays in succession.  
[ONE] :The first 10 seconds of each track of the current disc plays in succession.  
[OFF] : Intro play will be off.  
Random Play  
Touch [RDM] to select [ONE]. [ALL] or [OFF]  
[ALL] : All the tracks of all discs plays in random order.  
[ONE] : All the tracks on the current disc plays in random order.  
[OFF] : Randpm play will be off.  
14  
Navigation Operation with Touch Keys  
Setting Up  
1. Touch [SETUP] and then Touch [EXT. DEVICE] to show the menu.  
2. Touch [NAVI] to select a navigation Input source.  
Each time [NAVI] is touched, Input source is switches as follows.  
<Version 1>  
NONE -> NOVA -> DW -> NONE  
[NONE]:Select no navigation unit is connected to the unit.  
[NOVA]or [DW]:Select RGB output of your navigation is connected to [RGB] input of the main unit.  
* The factory default setting is [NONE].  
<Version 2>  
NONE -> RGB -> AV 1 -> AV 2 -> NONE  
[NONE] No navigation unit is connected to the unit.  
[RGB] RGB output of your navigation is connected to [RGB] input of the main unit.  
[AV1] AV output of your navigation is connected to [AV1] input of the AV control box.  
[AV2] AV output of your navigation is connected to [AV2] input of the AV control box.  
* The factory default setting is [NONE].  
* Check the version of your unit and set up according to the version  
Watching the Picture of Navigation  
1. Touch [MODE] to show the mode menu.  
2. Touch [NAVI]. The screen shows the picture of the navigation  
or press [MODE] button on the main unit repeatedly until [NAVI] mode is selected.  
*When your navigation unit is connected to AV1 or AV2 input of the AV control  
box, set up AV1/AV2 [ON] and then select AV1/AV2 mode to watch the picture of the navigation.  
*The car navigation system is an optional item. This unit only offers input for the system.  
Rear View Camera Operation with Touch Keys  
Setting Up  
1. Touch [SETUP] and then Touch [EXT. DEVICE] to show the menu.  
2. Touch [RVC] to select [ON] or [OFF]  
Each time [RVC] is touched, [ON] or [OFF] is selected.  
3. Select [ON] when a rear view camera is connected to [RVC] input of the AV control box.  
or select [OFF] when no rear view camera is connected to.  
*The factory default setting is [OFF].  
*Connect video output of your rear view camera to video input [RVC IN] of the AV control box.  
Watching the Picture of Rear View Canmera  
1. Touch [MODE] to show the mode menu.  
2. Touch [RVC] or set the rear gear on any mode.The monitor shows the picture of  
the back view camera picture.  
*A rear view camera is an optional item. This unit only offers input for the system.  
15  
k}kGz š›Œ”GzŒ››•ŽšGž›G{–œŠGrŒ  
XU{–œŠG[MODE] G’Œ GG›–Gš–žG›ŒG”–‹ŒG”Œ•œGˆ•‹G›Œ•G›–œŠG[DVD] G›–GšŒ“ŒŠ›Gk}kG”–‹ŒU  
YU{–œŠG[Setup] G›–Gš–žGk}kGšŒ›œ—G”Œ•œUG{ŒGšŠ™ŒŒ•Gš–žšG–““–ž•ŽG”Œ•œU  
SETUP MENU -- MAIN PAGE  
GENERAL SETUP  
SPEAKER SETUP  
AUDIO SETUP  
PREFERENCES  
EXIT SETUP  
QGpG[Setup] GšG›–œŠŒ‹SG—“ˆ ‰ˆŠ’Gž““G‰ŒG—ˆœšŒ‹Gˆ•‹G›ŒGšŠ™ŒŒ•Gš–žšG›ŒGšŒ›œ—G”Œ•œU  
ZU{–œŠG‚̵„SG‚̷„SG‚ඔ„SG–™G‚ඖ„G›–GšŒ“ŒŠ›Gˆ•‹Gˆ‹‘œš›G›ŒG›Œ”U  
GGG‚̵„GaGw™ŒššG›–GšŒ“ŒŠ›Gœ——Œ™G›Œ”U  
GGG‚̷„GaGw™ŒššG›–GšŒ“ŒŠ›G“–žŒ™G›Œ”U  
GGG‚ඔ„GaGw™ŒššG›–GšŒ“ŒŠ›G“Œ›G›Œ”U  
GGG‚ඖ„GaGw™ŒššG›–GšŒ“ŒŠ›G™Ž›G›Œ”U  
[U{–œŠG‚ඔ̅„G(Enter)G ›–GŒŸŒŠœ›ŒG›ŒGšŒ“ŒŠ›Œ‹G›Œ”šG–™GšˆŒG›ŒGŠˆ•ŽŒš  
16  
General Setup  
PIC MODE  
Select according to the disc recording format. If you are not sure of the recording  
format, it is recommended to select [AUTO].  
[AUTO]: Automatically select the image mode according to the disc recording format.  
[HI-RES]: Play with high resolution for TV format.  
[NON-FLICKER]: Selected to lower flash playing for movie format.  
*The factory default setting is [AUTO].  
ANGLE MARK  
Select according to the disc-recording format. You can set up so that the angle mark  
appears on the screen where the angles can be swithced.  
[ON] : To show angle mark on the screen.  
[OFF] : To close angle mark.  
*The factory default setting is [ON].  
OSD LANGUAGE  
Select a desired language for On-Screen Display (OSD) to set it.  
[ENGLISH] : English OSD is selected.  
[KOREAN] : Korean OSD is selected.  
*The factory default setting is [ENGLISH].  
CAPTIONS  
Select [ON] or [OFF] to set the display captions on or off.  
*The factory default setting is [OFF].  
MAIN PAGE  
Select [MAIN PAGE] to return to "SETUP MENU -- MAIN PAGE" menu.  
17  
z—Œˆ’Œ™GzŒ›œ—GVGhœ‹–GzŒ›œ—  
kv~utp  
zŒ“ŒŠ›GˆG‹Œš™Œ‹Gˆœ‹–G–œ›—œ›G”–‹ŒU  
[LT/RT]: zŒ“ŒŠ›G–™Gw™–Gs–ŽŠG“Œ›Gˆ•‹G™Ž›Gˆœ‹–G–œ›—œ›U  
[STEREO]: zŒ“ŒŠ›G–™Gš›Œ™Œ–Gˆœ‹–G–œ›—œ›U  
[OFF]: zŒ“ŒŠ›G–™G\UXGjˆ••Œ“Gˆœ‹–G–œ›—œ›U  
QG{ŒGˆŠ›–™ G‹Œˆœ“›GšŒ››•ŽGš [STEREO] U  
h|kpvGv|{  
GzŒ“ŒŠ›GˆG‹Œš™Œ‹G–œ›—œ›G”–‹ŒG–™Gˆœ‹–GšŽ•ˆ“šU  
[ANALOG]: vœ›—œ›šGˆ•ˆ“–ŽGˆœ‹–GšŽ•ˆ“šG›™–œŽGyjhGŠ–••ŒŠ›–•U  
[SPDIF/RAW]: Gvœ›—œ›šG\UXGŠG‹Ž›ˆ“GšŽ•ˆ“šG›™–œŽG–—›Šˆ“GŠ–••ŒŠ›–•G›–GˆG‹Ž›ˆ“Gˆ”—“Œ™U  
[SPDIF/PCM]: vœ›—œ›šGYGŠG‹Ž›ˆ“GšŽ•ˆ“šG›™–œŽG–—›Šˆ“GŠ–••ŒŠ›–•G›–GˆG‹Ž›ˆ“Gˆ”—“Œ™U  
QG{ŒGˆŠ›–™ G‹Œˆœ“›GšŒ››•ŽGš [ANALOG] U  
QGzŒ“ŒŠ› [SPDIF/RAW] G–™ [SPDIF/PCM] žŒ•GˆG‹Ž›ˆ“Gˆ”—“Œ™GšGŠ–••ŒŠ›Œ‹  
GGG›–G›ŒGh}GŠ–•›™–“G‰–ŸU  
vwGtvkl  
zŒ“ŒŠ›Gˆœ‹–G–œ›—œ›G“ŒŒ“UGGGG  
[LINE OUT]aGz›ˆ•‹ˆ™‹Gˆœ‹–G–œ›—œ›G“ŒŒ“UGG  
[RF REMOD]aGp•Š™ŒˆšŒ‹Gˆœ‹–G–œ›—œ›G“ŒŒ“UGG  
QG{ŒGˆŠ›–™ G‹Œˆœ“›GšŒ››•ŽGš [RF REMOD] U  
k|hsGtvuv  
zŒ“ŒŠ›GˆG‹Œš™Œ‹Gˆœ‹–G–œ›—œ›G”–‹ŒU  
[STEREO]aGz›Œ™Œ–Gˆœ‹–G–œ›—œ›GG  
[L-MONO]aGsŒ›Gˆœ‹–G–œ›—œ›G–•“ GG  
[R-MONO]aGyŽ›Gˆœ‹–G–œ›—œ›G–•“ UGG  
[MIX-MONO]aGsŒ›Gˆ•‹G™Ž›G‰–›Gˆœ‹–G–œ›—œ›GG  
QG{ŒGˆŠ›–™ G‹Œˆœ“›GšŒ››•ŽGš [STEREO] U  
wyvGsvnpj  
zŒ›Gœ—Gk–“‰ Gw™–Gs–ŽŠ  
[OFF]: k–“‰ Gw™–Gs–ŽŠGvU  
[ON]: k–“‰ Gw™–Gs–ŽŠGv•U  
[AUTO]: k–“‰ Gw™–Gs–ŽŠGhœ›–U  
QG{ŒGˆŠ›–™ G‹Œˆœ“›GšŒ››•ŽGš [ON] U  
swjtGv|{w|{  
zŒ“ŒŠ›GˆŠŠ–™‹•ŽG›–GwjtG–œ›—œ›G™Œ˜œŒ•Š G–G –œ™G‹Ž›ˆ“Gˆ”—“Œ™U  
[LPCM 48K]  
[LPCM 96K]  
QG{ŒGˆŠ›–™ G‹Œˆœ“›GšŒ››•ŽGš [LPCM 96K] U  
18  
Preferences  
AUDIO  
Select a desired audio language.  
KOREAN, ENGLISH, FRENCH, SPANISH, CHINESE, JAPANESE  
*The factory default setting is [ENGLISH].  
*This option is available only when the language selected is recorded in the disc.  
SUBTITLE  
Select a desired subtitle language.  
KOREAN, ENGLISH, FRENCH, SPANISH, CHINESE, JAPANESE, OFF  
*This option is available only when the language selected is recorded in the disc.  
*The factory default setting is [ENGLISH].  
DISC MENU  
Select a desired DVD menu language.  
KOREAN, ENGLISH, FRENCH, SPANISH, CHINESE, JAPANESE  
*This option is available only when the language selected is recorded in the disc.  
*The factory default setting is [ENGLISH].  
PARENTAL  
This is to cut scenes that are unfavorable for children. Select a desired parential lock.  
When a parential lock is selected, you need to input a password to see the picture.  
1. G  
2
3. PG  
4. PG - 13  
5
6. PG - R  
7. NC - 17  
8. ADULT  
*The factory default setting is [8 ADULT].  
PASSWORD  
You can change the old password (4-digit) to new one (4-digit).  
1. Select [PASSWORD] and [CHANGE].  
2. Input an old password with number button on the remote control and touch [ENTER].  
3. Input a new password with number button on the remote control, and touch [ENTER].  
4. Input a new password again in the [CONFIRM] and touch [ENTER].  
*Factory default setting is "No Password".  
DEFAULTS  
Select [RESET] and touch [ENTER] to reset all saved items to the factory defaults.  
19  
DVD Video Operation with Touch Keys  
1. Insert a DVD disc into the disc slot hole.  
The mode automatically switches to DVD mode and Playback starts.  
2. Press the [OPEN/CLOSE] button to open the monitor.  
*In case playback does not operate normally, press the [RESET]  
button with a pointed object to restart the operation.  
Switching the NTSC/PAL system.  
You can switch the video system. See "Selecting Video System" in  
TV operations with Touch Key in Page 13.  
Pausing Disc Play  
Touch [ II] to pause playback. Touch [ II] again to resume playback.  
Stopping Disc Play  
Touch [ ] to stop playback. Touch [  
] or [ II] to resume playback.  
Fast Forward Play  
Touch [  
] for fast forward.  
] is touched, the fast forward speed goes from 2X, 8X, 16X, 32X, 64X  
Each time [  
to normal playback.  
Fast Backward play  
Touch [  
] for fast backward.  
] is touched, the fast backward speed goes from 2X, 8X, 16X, 32X, 64X  
Each time [  
to normal playback.  
Chapter Search  
1.Touch [I  
2.Touch [  
] to search the chapter number to backward.  
I] to search the chapter number to forward.  
DVD Video operations with the remote control  
Disc Menu  
1. Press the [TITLE] button to show root menu on the screen.  
2. Press the [ ], [ ], [ ], or [ ] button to select the desired menu.  
3. Press the [ENTER] button to confirm and play the selected menu.  
Switching the Subtitle Language  
Press the [SUB-T] button repeatedly until the desired subtitle languge is selected.  
*This function only available when there are two or more languages recorded in the disc.  
Switching the Audio Language  
Press the [AUDIO] button repeatedly until the desired audio languge is selected.  
*This function only available when there are two or more languages recorded in the disc.  
20  
Slow Playback  
1. Press the [SLOW] button. Each time the [SLOW] button is pressed, the slow playback  
speed goes from forward 2X, 4X, 8x, backward 2X, 4X, 8X to normal playback.  
2. Press the [ II] button to return to normal playback.  
*There is no sound during slow playback.  
Frame by Frame Playback  
1. Press the [STEP] button. Press the button again to show next image.  
2. Press the [ II] button to return to normal playback.  
*There is no sound during frame by frame playback.  
Repeat Playback  
Each time the [REPEAT] button is pressed, the repeat function switches as follows.  
CHAPTER REPEAT -> TITLE REPEAT -> REPEAT OFF -> CHAPTER REPEAT  
Repeat between A and B Scene  
1. Press the [A-B] button at the beginning of the desired scene.  
2. Press the [A-B] button again at the end of the desired scene.  
The scene from A to B continues repeating.  
3. Press the [A-B] button again to cancel REPEAT A-B.  
Searching with a Chapter/Title number  
1. Press the [SEARCH] button to show chapter and title number.  
2. Press the [ ] or [ ] button to select chapter or title.  
3. Input the number of the chapter or title that you want to play back with the [0] to [9] key.  
4. Press the [ENTER] button to confirm and play the selected chapter/title number.  
Viewing Zoom  
1.Each time the [ZOOM] button is pressed. The size of image changes from X1.5, X2, X3 to normal.  
2. While zooming, press [ ], [ ], [ ], or [ ] to scroll the image.  
3. Press [ II] button to return to normal playback.  
Time Display  
*Each time the [DISPLAY] button is pressed, the time display during playback switches as follows.  
1. Displaying the elapsed time of the current title.  
2. Displaying the remaining time of of the current title.  
3. Displaying the elapsed time of the current chapter.  
4. Displaying the remaining time of of the current chapter.  
5. Time display off.  
21  
VCD Operation with Touch Keys  
1. Insert a VCD disc into the disc slot hole.  
The mode automatically switches to DVD mode and Playback starts.  
2. Press the [OPEN/CLOSE] button to open the monitor.  
3. Touch the screen to show the touch keys.  
Pausing Disc Play  
Touch [ II] to pause playback. Touch [ II] again to resume playback.  
Stopping Disc Play  
Touch [ ] to stop playback. Touch [  
] or [ II] to resume playback.  
Fast Forward Play  
Touch [  
Each time [  
] for fast forward.  
] is touched, the fast forward speed goes from 1X, 2X, 3X, 4X to normal playback.  
Fast Backward play  
Touch [  
Each time [  
] for fast backward.  
] is touched, the fast backward speed goes from 1X, 2X, 3X, 4X to normal playback.  
VCD operations with the remote control  
Slow Playback  
1. Press the [SLOW] button. Each time [SLOW] button is pressed, the slow playback speed goes  
from forward 2X, 4X, 8x, backward 2X, 4X, 8X to normal playback.  
2. Press [ II] button to return to normal playback.  
*There is no sound during slow playback.  
Frame by Frame Playback  
1. Press the [STEP] button. Press the button again to show next image.  
2. Press the [ II] button to return to normal playback.  
*There is no sound during frame by frame playback.  
Repeat between A and B Scene  
1. Press the [A-B] button at the beginning of the desired scene.  
2. Press the [A-B] button again at the end of the desired scene.  
The scene from A to B continues repeating.  
3. Press the [A-B] button again to cancel REPEAT A-B.  
Viewing Zoom  
1.Each time the [ZOOM] button is pressed. The size of image changes from X1.5, X2, X3 to normal.  
2. While zooming, press the [ ], [ ], [ ], or [ ]button to scroll the image.  
3. Press the [ II] button to return to normal playback.  
22  
Listening to CD with Touch Keys  
1. Insert a Music CD disc into the disc slot hole.  
The mode automatically switches to DVD mode and Playback starts.  
2. Press the [OPEN/CLOSE] button to open the monitor.  
3. Touch the screen to show the touch keys.  
Pausing Disc Play  
Touch [ II] to pause playback. Touch [ II] again to resume playback.  
Stopping Disc Play  
Touch [ ] to stop playback. Touch [  
] or [ II] to resume playback.  
Fast Forward Play  
Touch [  
Each time [  
] for fast forward.  
] is touched, the fast forward speed goes from 1X, 2X, 3X, 4X to normal playback.  
Fast Backward play  
Touch [  
Each time [  
] for fast backward.  
] is touched, the fast backward speed goes from 1X, 2X, 3X, 4X to normal playback.  
Track Search  
1.Touch [I  
2.Touch [  
] to search the track number to backward.  
I] to search the track number to forward.  
CD operations with the remote control  
Repeat Play  
Press the [REPEAT] button to select [ONE], [ALL] or [OFF].  
[ALL]: All the track on the current disc plays repeatedly  
[ONE]:The selected track on the current disc plays repeatedly.  
[OFF]: Repeat play will be off.  
Random Play  
Press the [RANDOM] button to select [ON] or [OFF].  
[ON]: All the tracks on the current disc plays in random order.  
[OFF]: Randpm play will be off.  
Repeat between A and B Section  
1. Press the [A-B] button at the beginning of the desired section.  
2. Press the [A-B] button again at the end of the desired section.  
The section set from A to B continues repeating.  
3. Press the [A-B] button again to cancel REPEAT A-B.  
23  
Listening to MP3 with Touch Keys  
1. Insert an MP3 disc into the disc slot hole.  
The mode automatically switches to DVD mode and Playback starts.  
2. Press the [OPEN/CLOSE] button to open the monitor.  
3. Touch the screen to show the touch keys.  
4. Touch [ ], [ ], [ ] or [ ] to select the folder and touch [  
] key.  
5. Touch [ ], [ ], [ ] or [ ] to select the file that you want to play and touch [  
] key.  
Pausing Disc Play  
Touch [ II] to pause playback. Touch [ II] again to resume playback.  
Stopping Disc Play  
Touch [ ] to stop playback. Touch [  
]or [ II] to resume playback.  
Fast Forward Play  
Touch [  
Each time [  
] for fast forward.  
] is touched, the fast forward speed goes from 2X, 4X, 6X, 8X to normal play.  
Fast Backward play  
Touch [  
Each time [  
] for fast backward.  
is touched, the fast backward speed goes from 2X, 4X, 6X, 8X to normal playback.  
Track Search  
1.Touch [I  
2.Touch [  
] to search the track to backward.  
I] to search the track to forward.  
MP3 operations with the remote control  
Repeat Play  
Press the [REPEAT] button to select [REP-ONE], [FOLDER REPEAT] or [FOLDER].  
[REP-ONE]: The selected track on the current folder plays repeatedly.  
[FOLDER REPEAT]: All the tracks on the current folder play repeatedly  
[FODER]: Repeat play will be off.  
Random Play  
Press the [RANDOM] button to select [RANDOM], [SHUFFLE-ON] or [FOLDER].  
[RANDOM]: All the tracks on the current folder plays in random order.  
[SHUFFLE ON]:The selected track on the current folder plays in random order.  
[FOLDER]: Random play will be off.  
24  
Accessries  
Main Unit  
Remote control with a battery x each 1EA  
NINET Cable x 1EA  
Touch Ceramic Pen x1EA  
Trim Plate x 1EA  
Mounting Half Sleeve x 1EA  
Mounting Bracket x1EA  
Removal Key x 2EA  
Hex Head Screw (M5 x 15mm) x 4EA  
Binding Head Screw (#15 x 15) x 1EA  
Spring Washer 5.2 x 1EA  
Plate Washer 5.2x 1EA  
Power Cable x 1EA  
Cleaning Cloth x 1EA  
AV control Box  
Power Cable x 1EA  
Mounting Bracket x 2EA  
Binding Head Screw (M4 x 6mm) x 4EA  
Binding Head Screw (M5 x 16mm) x 4EA  
Installing the A/V Control Box  
Install the A/V Control Box on  
somewhere under a front seat.  
25  
Installation  
Installing the Unit  
1. Place the universal mounting bracket (Half Sleeve) into the instrument panel and bend  
each stopper of the mounting bracket inward by a screwdriver.  
2. Insert the unit into the mounting bracket until it locks after connecting the wires.  
3. Mount the outer escutcheon so that all the hooks are looked.  
Removing the unit  
1. Unfasten the hex nut when the rear of the unit has been secured with it.  
2. Remove the outer escutcheon.  
3. Insert the 2 keys as the figure between the spring and the mounting bracket,  
then pull the unit out.  
*Keep the 2 keys in safe. You cannot remove the unit without it.  
1. Make sure to ground the unit to a negative 12V DC power supply  
2. When replacing a fuse, only use a new one with the prescrived rating. Using a fuse with wrong  
rating may cause the unit to malfunction.  
3. To prevent short circuits when replacing a fuse, first disconnect the wiring harness.  
4. Do not use any screws except for the ones provided. Using improper screws may damage the unit.  
5. If you experience problems during installation, consult your supplier.  
26  
Wire Connection  
1. Be sure that the PARKING SENSOR WIRE must be grounded or opened.  
If it is connected to ACC (B+). The unit can be damaged.  
2. Do not ground the POWER ANTENNA wire. If it is grounded, the unit can be damaged.  
27  
Connection for AV Equipments  
28  
Connection for AV Equipments  
29  
Troubleshooting guide  
What might appear to be malfunction in your unit may just be the result of slight misoperation or  
miswiring. Before calling service, first check the following table for possible problems.  
Problem  
Possible Cause  
Solution  
After checking for short  
circuits in the wires, replace  
the fuse with one having the  
same rating.  
The fuse has blown.  
The power does not turn  
No ACC position on  
vehicle ignition.  
Connect the same wire to the  
ignition as the battery wire.  
The computer chip in the  
unit is not functioning  
normally.  
Nothing happens when  
the buttons are pressed.  
Press the reset button on  
the unit.  
For safety reasons, the  
monitor does not open  
while the vehicle is  
moving. Engaging the  
parking brake.  
The monitor does not  
open / close.  
The parking brake is not  
engaged.  
The unit is not connected  
to the parking brake  
detection switch.  
Make proper connections  
according to "wire  
connection"  
For safety reasons no  
television/video images  
are displayed while the  
vehicle is moving.  
Engaging the parking  
brake will cause images  
to be displayed.  
No television/video  
image appears  
The parking brake is not  
engaged.  
Television/video  
image appears black-white.  
The color system is set  
incorrectly.  
Please switch to correct  
color system from menu.  
If the temperature of the  
monitor drops, the screen  
may appear darker when  
power is first turned on  
due to the characteristics  
of a liquid crystal panel.  
Wait a while Normal  
brightness will return.  
When the unit is set to  
auto dimmer, it is not  
linked to the vehicle's  
light switch.  
Make propper connections  
according to  
" Wire connection."  
Separate the two antennas  
as far as possible.  
Turn off the main unit.  
Turn off Attenuator.  
Reconnect the input/output  
wires or the wiring  
The unit is a location  
where temperature is low.  
The screen is dark.  
The unit is set to auto  
dimmer.  
The screen does not  
darken when the  
vehicle's lights are  
turned on.  
The illumination wire has  
not been connected.  
(If manual dimmer is set)  
The TV antenna and  
vehicle's radio antenna  
are to close.  
Attenuator is turned on.  
The fader or balance  
settings are set all the  
way to one side.  
AM/FM radio reception  
is poor and/or  
there is noise.  
No sound can be heard,  
or the volume is low.  
harness correctly.  
Reconnect the input/output  
wires or the wiring  
The input/output wires or  
wiring harness are  
connected in correctly.  
harness correctly.  
30  
Troubleshooting guide  
Problem  
Possible Cause  
Solution  
Reset the fader and/or  
balance settings.  
One of the speaker wires  
is being pinched by a  
screw in the car.  
The sound quality is poor or  
distorted.  
The speakers are not  
wired correctly.  
Reconnect the speaker  
wires so that each output  
terminal is connected to a  
different speaker.  
The car antenna is not  
extended.  
Pull the antenna out all the way.  
Radio reception is poor.  
The antenna control wire is not  
connected.  
The battery wire has not  
been connected to the  
proper terminal.  
Connect the wire correctly,  
referring to the section on "connections".  
Connect the wire correctly,  
referring to the section on  
"connections".  
The memory is erased  
when the ignition is  
turned off.  
The disc is scratched or  
dirty.  
Random play has been  
selected.  
Clean the disc.  
The sound/picture skips  
on a DVD/VCD/CD.  
A track will not play.  
Turn off random play.  
The subtitle cannot be displayed  
when the DVD disc being played  
does not contain the recording of  
subtitles.  
The DVD disc being  
played does not contain  
the recording of subtitles.  
The subtitle is not  
displayed.  
The DVD disc being  
played does not contain  
the recording of more  
than one audio (or  
subtitle) language.  
The DVD disc being  
played does not contain  
the recording of more  
than one angle.  
You are attempting to  
switch the angle in a  
DVD section where more  
than one angle is not  
recorded.  
The voice (or subtitle) language  
cannot be changed when the DVD  
disc being played does not contain  
the recording of more than one  
voice(or subtitle) language.  
The voice(or subtitle)  
language cannot be  
changed.  
The viewing angle cannot be  
changed when the DVD disc being  
played does not contain the  
recording of more than one angle.  
More than one viewing angle may  
be recorded only in limited  
sections in a disc.  
The viewing angle cannot  
be changed.  
Playback will not start  
even after a title is  
selected.  
A viewing restriction  
(RATING) has been set  
for the disc.  
Check the viewing restriction  
level(RATING) setting.  
The DVD disc being  
played does not contain  
the recording of the  
selected voice or subtitle  
language.  
The voice or subtitle  
language selected in the  
]initial setting is not  
played.  
level(RATING) setting.  
recording of the selected voice or  
subtitle language.  
Remote control does not  
work  
Replace the batteery with one  
having the same rating.  
The battery runs out.  
31  
Specifications  
Power Requirement  
14.4V DC (11~16V)  
2A  
DVD Monitor  
Junction Box  
Current Consumption  
10A  
Operating Temperature  
Storage Temperature  
-10 ~ 60  
-20 ~ 80  
General  
Total  
178(W) X 50(H) X 190(D)  
178(W) X 50(H) X 165(D)  
DVD Monitor Install  
Size  
Weight  
Total  
257(W) X 40(H) X 187(D)  
JunctionBox  
Weight  
Display Size  
7 Inch Wide  
LCD Type  
Transparent Type TN LCD  
TFT Active Matrix  
Drive Method  
Monitor Section  
Number of Pixels  
Back Lighting  
336,960(1,440 X 234)  
U-Shaped Cold Cathode Fluorescent Tube  
NTSC/PAL Switchable  
Viseo System  
Maximum Power Output  
Pre Output Voltage  
45W  
4ch  
35W  
1ch (Center)  
RMS  
1V  
1.2V  
4
5chRMS1V  
RMS  
Subwoofer Output Voltage RMS  
Speaker Impedance  
Decoder  
Audio Section  
Linear PCM / Dolby Digital /Dolby Pro Logic / DTS  
Classic/Rock/Pops/Jazz  
Available  
EQ  
3D Sound  
Bass/Treble Control Range  
System  
10dB  
DVD Video / VCD /CD / dtsCD / MP3  
96 / 24bit  
D/A converter  
DVD Player Section  
FM Radio Section  
Channels  
5.1ch / 4ch Don Mix  
MPEG-1&2 Audio Layer 3  
87.5 ~ 108  
MP3 Decoding Format  
Frequency Range  
Manual Tuning 50  
Frequency Step  
Seek Tuning 100  
Usable Sensitivity  
Stereo Separation  
S/N Ratio  
15dB (S/N=30dB)  
25dB  
50dB  
USA Band  
530 ~ 1710  
Frequency Range  
Frequency Step  
Europe Band  
USA Band  
522 ~ 1620  
10  
AM Radio Section  
TV Tuner Setion  
Europe Band  
9
Usable Sensitivity  
Image Rejection Ratio  
System  
35dB (S/N=20dB)  
45dB  
NTSC / PAL-BG / PAL-DK / PAL-I  
2 ~ 13 (VHF), 14 ~ 69 (UHF)  
E2 ~ S41 (VHF), E21 ~ E69 (UHF)  
NTSC  
PAL  
Channel Coverage  
Antenna Input  
4 ch Diversity (75  
1.0Vpp / 75  
1.0Vpp / 75  
1.0V / 22  
)
Video Input Voltage  
Input/Output Section Video Output Voltage  
Audio Input Voltage  
32  

Rinnai QPA 09 0001 User Manual
RCA CC6251 User Manual
Plantronics 50 0230B 004 User Manual
Pioneer DEH P4800MP User Manual
Panasonic PALMCORDER PV L60 User Manual
Panasonic CQ C3401 User Manual
Panasonic Car Stereo System CQ BT5107U User Manual
Oster 133086 User Manual
Manitowoc Ice MFD 51 User Manual
Kenwood CASSETTE RECEIVER KRC 778RV User Manual