Nokia BH 112 User Manual

Nokia Bluetooth Headset BH-112 User Guide  
Issue 1.1  
3
Get started  
Keys and parts  
7
6
1
2
5
3
4
1
2
3
4
5
6
7
Charger connector  
Indicator light  
Power key  
Microphone  
Call key  
Earpiece  
Earloop  
Start using your headset  
When you switch on your headset for the first time, a voice prompt helps you set up  
your headset. Voice prompts are not available in all languages.  
The headset comes with different sized earpads. Select the earpad that fits the best and  
is the most comfortable for your ear. To change the earpad, pull the current earpad from  
the earpiece, and push the new earpad into place.  
1
To switch the headset on, press and hold  
for 2 seconds. If the headset doesn't  
switch on, charge the battery.  
2
3
Gently push the earpiece into your ear.  
To pair the headset with a compatible phone, follow the voice prompt.  
Charge the battery  
Before using the headset, you must charge the battery.  
4
Warning:  
Use only chargers approved by Nokia for use with this particular model. The use of any  
other types may invalidate any approval or warranty, and may be dangerous. Use of  
unapproved chargers may present a risk of fire, explosion, or other hazard.  
1
2
Connect the charger to a wall outlet.  
Connectthe charger cable to the charger connector onthe headset. Thered indicator  
light turns green when the battery is fully charged.  
3
Disconnect the charger from the headset, then from the wall outlet.  
When you unplug a charger, hold and pull the plug, not the cord.  
The fully charged battery has power for up to 5 hours of talk time or up to 150 hours of  
standby time.  
When the battery charge is low, you hear a voice prompt, the headset beeps every 5  
minutes, and the red indicator light flashes. When the battery is charging, the red  
indicator light is on.  
Check the battery charge  
Make sure the headset is switched on, and press . A green light indicates a sufficient  
charge level. If the light is yellow, you may need to recharge the battery soon. If the  
light is red, recharge the battery.  
Switch the headset on or off  
Switch on  
Press and hold  
once.  
for 2 seconds. The headset beeps, and a green indicator light flashes  
The headset connects to the last connected device. If you have never paired the headset  
with a device, or you have cleared the device pairings, pairing mode is activated.  
Switch off  
Press and hold  
for 2 seconds. The headset beeps, and a red indicator light flashes  
once. All active calls are ended.  
If not connected to a device within 30 minutes, the headset switches off.  
Pair and connect the headset to your phone  
Before using the headset, you must pair and connect it to a compatible phone.  
5
1
2
3
To switch the headset off, press and hold  
Switch on the phone to pair with.  
for 2 seconds.  
If you have never paired the headset with a phone, or you have cleared the phone  
pairings, switch the headset on.  
If you have previously paired your headset with another phone, press and hold  
for 5 seconds.  
Pairing mode is activated, and a green indicator light starts to flash quickly. Follow  
the voice prompt.  
4
Within 3 minutes, activate Bluetooth on the phone, and set it to search for Bluetooth  
devices. For details, see the user guide of the phone.  
5
6
Select the headset from the list of found devices.  
If required, enter the passcode 0000.  
You can pair your headset with 8 compatible phones, but you can only connect it to a  
maximum of 2 phones at the same time.  
With some phones, you may need to make the connection separately after pairing.  
Wear the headset  
If you want to use the headset with the earloop, attach the earloop to the headset. To  
detach the earloop, gently pull it from the headset.  
Slide the earloop behind your ear, and gently push the earpiece against your ear.  
Carefully bend the earloop around your ear for the best fit. Point the headset towards  
your mouth.  
6
Make calls  
Make and receive calls  
To make and receive calls using your headset, you need to connect it to your phone.  
Make a call  
Make a call in the normal way.  
Answer a call  
Press  
.
End a call  
Press  
.
Reject a call  
Press  
twice.  
Switch a call between your headset and phone  
Press and hold  
for 2 seconds.  
You can redial the last called number or use voice dialling, if your phone supports these  
features with the headset.  
Redial the last called number  
When no call is in progress, press  
twice.  
Use voice dialling  
When no call is in progress, press and hold  
in the user guide of your phone.  
for 2 seconds, and follow the instructions  
7
Change the volume  
Set the desired volume level on your connected mobile device. The selected volume level  
is saved as the minimum volume level for the device that is currently connected to the  
headset.  
Pair and connect the headset to two phones  
When you use the headset for the first time, it automatically connects to your phone.  
You can also connect your headset to another phone, and manage calls from, for  
example, both your personal and your work phone at the same time.  
1
2
3
Make sure Bluetooth is activated on both phones.  
To switch the headset off, press and hold  
for 2 seconds.  
for 5 seconds, and pair the headset  
To activate pairing mode, press and hold  
with the second phone.  
4
Switch the headset off and back on. The headset connects to both phones.  
To use your headset with just one phone again, activate pairing mode, and press and  
hold and for 5 seconds.  
Handle calls from two phones  
If your headset is connected to two phones, you can handle calls from both at the same  
time.  
End an ongoing call, and answer a call on another phone  
Press  
.
Put an ongoing call on hold, and answer a call on another phone  
Press and hold for 2 seconds.  
Switch between active and held calls  
Press and hold for 2 seconds.  
End an ongoing call, and activate a held call  
Press  
.
If you redial or use voice dialling, the call is made on the phone you last had an active  
call on with the headset.  
Settings  
Clear device pairings  
1
To switch the headset off, press and hold  
for 2 seconds.  
8
2
3
Press and hold  
and  
for 9 seconds. The headset beeps twice, and the red and  
green indicator lights alternate.  
When the headset switches on, follow the voice prompt. Pairing mode is activated.  
Deactivate voice prompts  
1
2
To switch the headset off, press and hold  
for 2 seconds.  
Press and hold for 5 seconds. Pairing mode is activated, and a blue indicator  
light starts to flash quickly.  
3
Press and hold  
for 5 seconds. You hear a voice prompt, and a yellow indicator  
light flashes once.  
Activate voice prompts  
1
2
To switch the headset off, press and hold  
for 5 seconds.  
Press and hold for 5 seconds. Pairing mode is activated, and a blue indicator  
light starts to flash quickly.  
3
Press and hold  
for 2 seconds. You hear a voice prompt, and a green indicator  
light flashes once.  
Troubleshooting  
Cannot connect the headset to a compatible device? Make sure the headset is  
charged, switched on, and paired with the device.  
Did the headset stop functioning even though it is charged? Plug the charger into  
a wall outlet, and while you press and hold the power key, connect the headset to  
the charger.  
Product and safety information  
Battery and charger information  
This device has an internal, nonremovable, rechargeable battery. Do not attempt to remove the battery from the device as you  
may damage the device.  
This device is intended for use when supplied with power from the following chargers: AC–11. The exact charger model number  
may vary depending on the type of plug. The plug variant is identified by one of the following: E, X, AR, U, A, C, K, or B.  
The battery can be charged and discharged hundreds of times, but it will eventually wear out.  
Talk and standby times are estimates only. Actual times are affected by, for example, device settings, features being used,  
battery condition, and temperature.  
If the battery has not been used for a long time, to begin charging, you may need to connect the charger, then disconnect and  
reconnect it.  
If the battery is completely discharged, it may take several minutes before the charging indicator is displayed.  
9
When your charger is not in use, unplug it from the electrical plug and the device. Do not leave a fully charged battery connected  
to a charger, as overcharging may shorten the battery’s lifetime. If left unused, a fully charged battery will lose its charge over  
time.  
Always keep the battery between 15°C and 25°C (59°F and 77°F). Extreme temperatures reduce the capacity and lifetime of the  
battery. A device with a hot or cold battery may not work temporarily.  
Do not dispose of batteries in a fire as they may explode. Dispose of batteries according to local regulations. Recycle when  
possible. Do not dispose as household waste.  
Use the charger for its intended purpose only. Improper use or use of unapproved chargers may present a risk of fire, explosion,  
or other hazard, and may invalidate any approval or warranty. If you believe the charger is damaged, take it to a service centre  
for inspection before continuing to use it. Never use a damaged charger. Only use the charger indoors.  
Take care of your device  
Handle your device, charger and accessories with care. The following suggestions help you protect your warranty coverage.  
Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that corrode  
electronic circuits. If your device gets wet, allow the device to dry.  
Do not store the device in cold temperatures.  
Do not attempt to open the device.  
Unauthorised modifications may damage the device and violate regulations governing radio devices.  
Do not drop, knock, or shake the device.  
Only use a soft, clean, dry cloth to clean the surface of the device.  
Recycle  
Always return your used electronic products, batteries, and packaging materials to dedicated collection points. This way you  
help prevent uncontrolled waste disposal and promote the recycling of materials.  
Crossed-out wheeled-bin symbol  
The crossed-out wheeled-bin symbol on your product, battery, literature, or packaging reminds you that all electrical and  
electronic products, batteries, and accumulators must be taken to separate collection at the end of their working life. This  
requirement applies in the European Union. Do not dispose of these products as unsorted municipal waste. For more  
environmental information, see the product Eco profile atwww.nokia.com/ecoprofile.  
Copyright and other notices  
DECLARATION OF CONFORMITY  
Hereby, NOKIA CORPORATION declares that this BH-112 product is in compliance with the essential requirements and other  
relevant provisions of Directive 1999/5/EC. A copy of the Declaration of Conformity can be found at http://www.nokia.com/  
© 2011 Nokia. All rights reserved.  
10  
Nokia, Nokia Connecting People, and the Nokia Original Accessories logo are trademarks or registered trademarks of Nokia  
Corporation. Nokia tune is a sound mark of Nokia Corporation. Other product and company names mentioned herein may be  
trademarks or tradenames of their respective owners.  
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Nokia is under license.  
The availability of products may vary by region. For more information, contact your Nokia dealer. This device may contain  
commodities, technology or software subject to export laws and regulations from the US and other countries. Diversion contrary  
to law is prohibited.  
/Issue 1.1 EN  

PYLE Audio PL97M4 User Manual
Prince Castle Wedgers User Manual
Polk Audio SUBWOOFERDB SUB ENCLOSURE 101 DB804 User Manual
Philips VOX150 User Manual
Philips CQ DFX972N User Manual
Panasonic Palmcorder PV GS70 User Manual
Olympus 200447 User Manual
O'Brien SUPER SCREAMER 2081501 User Manual
MTX Audio MTX Thunder TA8502 User Manual
Motorola Radio GP320 User Manual