Nady Systems Car Speaker CX 222SW User Manual

O W N E R ’ S M A N U A L  
CX-22SW  
2-WAY STEREO PLUS SUBWOOFER  
WARNING  
An equilateral triangle enclosing a lightning flash/arrowhead symbol is  
intended to alert the user to the presence of uninsulated dangerous  
voltagewithin the products enclosure which may be of sufficient  
magnitude to constitute a risk of electric shock.  
ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR  
An equilateral triangle enclosing an exclamation point is intended to alert  
the user to the presence of important operating and service instructions in  
the literature enclosed with this unit.  
IMPORTANT SAFETY INSTRUCTIONS  
When using this electronic device, basic precautions should always be taken, including the following:  
1. Read all instructions before using the product.  
2. Do not use this product near water (e.g., near a bathtub, washbowl, kitchen sink, in a wet basement, or near a  
swimming pool, etc.).  
3. This product should be used only with a cart or stand that will keep it level and stable and prevent wobbling.  
4. This product, in combination with headphones or speakers, may be capable of producing sound levels that  
could cause permanent hearing loss. Do not operate for a long period of time at a high volume level or at a  
level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should consult an  
audiologist.  
5. The product should be positioned so that proper ventilation is maintained.  
6. The product should be located away from heat sources such as radiators, heat vents, or other devices  
(including amplifiers) that produce heat.  
7. The product should be connected to a power supply only of the type described in the operating instructions or  
as marked on the product. Replace the fuse only with one of the specified type, size, and correct rating.  
8. The power supply cord should: (1) be undamaged, (2) never share an outlet or extension cord with other  
devices so that the outlet’s or extension cord’s power rating is exceeded, and (3) never be left plugged into  
the outlet when not being used for a long period of time.  
9. Care should be taken so that objects do not fall into, and liquids are not spilled through, the enclosure’s  
openings.  
10. The product should be serviced by qualified service personnel if:  
A.  
B.  
The power supply cord or the plug has been damaged.  
Objects have fallen into, or liquid has been spilled onto the product.  
C. The product has been exposed to rain.  
D. The product does not appear to operate normally or exhibits a marked change in performance.  
E.  
The product has been dropped, or the enclosure damaged.  
11. Do not attempt to service the product beyond what is described in the user maintenance instructions. All  
other servicing should be referred to qualified service personnel.  
3
CONTROLS AND CONNECTIONS  
3
4
2
6
2
4
3
5
1
5
7
8
FRONT PANEL  
1.  
POWER SWITCH  
To turn the unit ON or OFF, press the upper or lower  
PLEASE READ THIS MANUAL  
BEFORE OPERATING THIS UNIT  
portion of this button. The internal power LED illuminates  
when the unit is turned ON. (Caution: Always turn the  
Crossover ON before the amplifier, and turn it OFF after  
the amplifier or transients harmful to the speakers  
may result.)  
Caution : To prevent malfunctioning  
and/or possible equipment damage:  
Before plugging the unit into the power  
source: (1) the voltage selector switch  
should be set for the correct voltage for  
your area (115V or 230V) and (2) all  
equipment connected to the crossover  
outputs should be turned off or all the  
inputs turned down.  
2.  
CROSSOVER FREQUENCY CONTROLS:  
These select the crossover frequencies of the LOW and  
HIGH ways. Theyre a low cut for the HIGH and a high  
cut for the LOW. You can select the frequencies  
between 250 Hz and 6 Hz.  
3.  
4.  
L/H OUTPUT LEVEL CONTROLS:  
These are used to adjust the output level of each way: LOW and HIGH .  
LOW CUT BUTTONS FOR LOW WAY:  
These insert low cut filters in the LOW way of each stereo channel with a 12dB/Octave, 30 Hz HPF  
to minimize problems from subsonic frequencies in the signal, to suppress hum, and to prevent low  
frequency speaker resonance.  
5.  
6.  
PHASE BUTTONS:  
These allow switching the polarity to invert the signal phase on the HIGH ways. This is done after  
the output levels are set to correct audible phase problems.  
Caution: Before pressing the PHASE BUTTON, always lower the outputs of your power amplifiers  
to avoid possible speaker damage.  
SUB CROSSOVER FREQUENCY CONTROL:  
This selects the crossover frequency of the SUB WOOFER way. You can select the frequency  
between 50 Hz to 250 Hz.  
7.  
8.  
SUBWOOFER OUTPUT LEVEL CONTROL:  
This is used to adjust the SUB WOOFER output level.  
SUBWOOFER LOW CUT BUTTON:  
This inserts a low cut filter in the SUBWOOFER way with a 12dB/Octave, 30 Hz HPF to minimize  
problems from subsonic frequencies in the signal, to suppress hum, and to prevent low frequency  
subwoofer speaker resonance.  
4
CONTROLS AND CONNECTIONS  
XLR  
R CHANNEL  
L CHANNEL  
BALANCE  
D
SUB  
PIN  
PIN  
PIN  
1
2
3
GND  
HI  
LO  
115V/60Hz  
230V/50Hz  
PHONE UNBAL  
NADY SYSTEMS, Inc.  
Emeryville, CA, USA  
Made in Taiwan  
AC IN  
FUSE 0.5A  
HIGH  
OUTPUT  
LOW  
INPUT  
WOOFER  
HIGH  
OUTPUT  
LOW  
INPUT  
12  
10  
11  
11  
13  
9
11  
10  
REAR PANEL  
9.  
FUSE COMPARTMENT:  
Replace with only the same type fuse (0.5A/250V). If it blows continuously, do not use the unit  
until it has been serviced by qualified personnel.  
10. STEREO INPUT CONNECTORS:  
Connect your L/R stereo input signal to either the balanced XLR or the unbalanced 1/4" phone jacks.  
11. OUTPUT CONNECTORS:  
Connect to your amplifiers via these unbalanced 1/4" phone jacks.  
12. AC VOLTAGE SELECTOR SWITCH:  
Before plugging in the power cord, check to see that the unit is set for the proper voltage for your  
area:~115V (60Hz) or ~230V (50Hz).  
13. POWER CONNECTOR  
The IEC jack is used to connect the power cord to the AC Power Source.  
(Caution: Do not remove the center grounding pin.)  
SPECIFICATIONS  
Crossover Type ..............................................................Stereo 2 ways + Subwoofer  
Crossover Range ............................................................Subwoofer: 50 - 250Hz, -24/10dB  
Low/High : 250-6000Hz, -24/10dB  
Filter Type (Slope) ..........................................................2nd order, 12dB/Octave  
Inputs  
Type ..............................................................................Balanced XLR and unbalanced 1/4"  
Impedance ....................................................................100K  
Outputs  
Type ..............................................................................Unbalanced 1/4"  
Impedance ....................................................................220Ω  
Low Cut Filters................................................................30Hz/ - 3dB, 12dB/Octave  
Frequency Response......................................................20Hz - 25KHz +/-1dB  
Total Harmonic Distortion (THD) + Noise ....................< 0.05 %  
S/N Ratio..........................................................................> 95 dB  
Fuse..................................................................................0.5 A/ 250V, 5mm glass type  
Dimensions......................................................................19’’ x 1.73’’ x 5.9’’ (483 X 44 X 150mm)  
Weight ..............................................................................4.4 lbs. (2.2 Kg)  
Specifications and design subject to change without prior notice for improvement purposes  
5
TYPICAL SET-UP  
6
SERVICE FOR YOUR NADY AUDIO PRODUCT  
(U.S.) Should your NADY AUDIO product require service, please contact the Nady Service Department via tele-  
phone at (510) 652-2411, or e-mail at [email protected].  
(International) For service, please contact the NADY AUDIO distributor in your country through the dealer from  
whom you purchased this product.  
DO NOT ATTEMPT TO SERVICE THIS UNIT  
YOURSELF AS IT CAN BE DANGEROUS  
AND WILL ALSO VOID THE WARRANTY.  
NADY SYSTEMS, INC. • 6701 SHELLMOUND STREET, EMERYVILLE, CA 94608  
Tel: 510.652.2411 • Fax: 510.652.5075 • www.nadywireless.com  

RayTek ThermoView Ti30 User Manual
Raypak 1501 User Manual
Pioneer AVX P7650DVD User Manual
Pioneer AVH P5150DVD User Manual
Panasonic Car Stereo System DEH 1350MP User Manual
Panasonic AW RP400N User Manual
Nortel Networks INTUITION 1000 User Manual
Lightning Audio B4652TK User Manual
Kenwood Car Stereo System KDC X995 User Manual
JVC LYT0404 001A User Manual