Miller Camera Support DS20 User Manual

DS5/DS10/DS20 Fluid Head Operators Manual  
#180 DS5 Fluid Head  
#182 DS10 Fluid Head  
#184 DS20 Fluid Head  
Introduction  
Camera  
screws  
Thank you for purchasing the Miller DS5/DS10/DS20 fluid head for  
use with our professional tripods and portable video camcorders. All  
fluid heads are 75mm ball levelling design and boast similar physical  
appearance and size. The DS5 utilises a single position  
counterbalance system to handle camera payloads up to 2.5kg  
(5.5lb). The DS10 utilises 2 selectable counterbalance positions to  
handle payloads from 2.5-5kg (5.5-11lb) while the DS20 offers 2  
selectable counterbalance positions for larger camcorders ranging  
from 5-10kg (11-22lb).  
1/4” and pin carriage  
Sliding camera plate  
Slide lock  
The DS5/DS10/DS20 fluid head is designed for maximum stability,  
accuracy and repeatability and includes 4 precision ball bearings  
and a fluid drag plate system in the pan and tilt assembly to deliver  
true fluid drag performance over a wide temperature range and  
payload. The DS10/DS20 fluid head also includes a friction drag  
adjustment.  
Tilt drag  
Pan handle clamp  
Counterbalance selector  
Pan lock  
The DS5/DS10/DS20 fluid head will give best performance when  
used on Miller SOLO DV (#1630, #1501) or Toggle Lightweight DV  
(#440, #420) tripod. This will ensure maximum system stability to suit  
any professional set-up. The DS5/DS10/DS20 fluid head will fit most  
industry standard 75 mm tripods as well, please refer to  
manufacturers’ manual for mounting details.  
Pan drag  
Handle Mounting  
The DS5/DS10/DS20 fluid head is supplied with a fixed length pan  
handle and clamp fitted to the right side of the head. A second  
pan handle can be attached to the DS5/DS10/DS20 for dual pan  
handle operation. Refer to spare parts section.  
75mm claw ball  
Clamp nut  
Fig 1.3  
DS20  
3
Operating Instructions  
Before using please read the following operating instructions.  
Do not omit any step. N.B. The safe operation of this piece of  
professional equipment is the responsibility of the operator.  
The 3/8” & 1/4” screws also allow the DS20 to attach to a  
proprietary Quick Release Tripod Adaptor or “tripod base plate”  
such as the Sony VCT-14 or Panasonic SHAN-TM700.  
2.1 Lock PAN and TILT LOCKS (rotate both levers clockwise until  
firm).  
1. Fluid Head Set-up  
2.2 Remove CAMERA PLATE from CAMERA PLATFORM by  
unlocking the SLIDE LOCK, pushing SAFETY TAB and sliding  
the CAMERA PLATE rearward  
1.1 Loosen the PAN HANDLE CLAMP fully, then rotate the PAN  
HANDLE until it is approximately perpendicular to the  
THREADED STUD and tighten the PAN HANDLE CLAMP -  
avoid contact wear between the serrations on the Fluid  
Head and the PAN HANDLE CLAMP, if this occurs then  
unwind the PAN HANDLE CLAMP further.  
2.3 With accessories and battery fitted to the camera, it is  
recommended to estimate the camera’s Centre of Gravity (C  
of G) for the purpose of correctly positioning the camera on  
the CAMERA PLATE. The camera’s C of G can be estimated by  
placing the camera on to a round rod and then shifting it  
backwards or forwards until a balance point – C of G - is  
achieved. It is recommended to identify this point as it will be  
useful in step 2.5.  
1.2 Ensure that the TRIPOD BOWL is approximately horizontal.  
Place the Fluid Head into the TRIPOD BOWL, adjust the  
BUBBLE LEVEL such that the bubble is inside the black  
circle and tighten the CLAMP NUT.  
1.4 Note:If adjusting the level with your camera mounted,  
first ensure the camera is securely held before loosening  
CLAMP NUT.  
2.4 Refer to the Camera’s owners manual for correct method of  
attachment to the CAMERA PLATE. Attach the camera or the  
Quick Release Tripod Adaptor to the CAMERA PLATE and  
securely tighten the screws.  
2. Camera Set-up  
2.5 Check that the SLIDE LOCK is loose, then align the  
CAMERA PLATE with the CAMERA PLATFORM and  
slide it forward until the safety mechanism is engaged.  
Then, slide the CAMERA PLATE so that the camera’s C of G  
is directly above the centre axis of the Fluid Head and tighten  
the SLIDE LOCK. If this can not be achieved then reposition  
the camera or the Quick Release Tripod Adaptor on the  
SLIDING PLATE – step 2.4. This will ensure that the system  
has maximum stability.  
Please note that the best camera control can be achieved by  
balancing camera centre of gravity (C of G) over centre axis of  
the head, and by selecting the appropriate counterbalance  
position to suit the weight of the camcorder payload.  
The DS5/DS10/DS20 is equipped with a sliding camera plate and  
a removable 1/4”-pin carriage which is standard mounting for DV  
and MiniDV camcorders. The DS20 is also fitted with a 3/8” &  
1/4” screws which is standard mounting for DVCAM (see Fig1.3).  
4
Operating Instructions  
3. Counterbalance  
Control  
4. Pan /Tilt Lock  
Control  
The DS5/DS10/DS20 Fluid Head offers high  
capacity calliper disc brake system to hold the  
Fluid Head in a fixed pan and/or tilt position.  
Camera position will not change when applying or  
releasing the Pan / Tilt locks.  
The counterbalance system was designed to neutralise the effect  
of the camera weight when it is tilted. The DS10 & DS20 Fluid  
Head offers a 2 position counterbalance system which can be  
operated via the COUNTERBALANCE SELECTOR (Fig. 2 & 3). The  
DS5 Fluid Head has a single position Counterbalance system and  
is preset. The COUNTERBALANCE SELECTOR must be operated  
when the SLIDING PLATFORM is in a horizontal position. After  
changing the Counterbalance setting it may be necessary to tilt  
the camera back and forth to ensure that the CB spring has  
engaged. The camera must be held securely while changing the  
Counterbalance setting.  
Do not pan or tilt the Fluid Head whilst the PAN or the TILT LOCK  
is partially applied.  
3.1 For safety ensure that Counterbalance position 2 is selected.  
3.2 Hold the camera and release the TILT LOCK, then gently tilt  
the camera from a horizontal position forward then backward  
and observe its response. If the Camera 'Springs Back' to the  
horizontal position then select  
Counterbalance position 1.  
Correct Counterbalance  
setting has been achieved  
when minimum effort is  
required to move the camera  
over the entire tilt range.  
TIP Fine tuning can be achieved  
Fig 3  
by adjusting the SLIDING  
PLATFORM - see step 2.5.  
Fig 2  
DS10 CB Selector  
DS20 CB  
Selector  
5
Operating Instructions Cleaning  
The DS5/DS10/DS20 fluid head features protective coatings, dust  
5. Pan /Tilt Drag  
Control  
seals and anti-corrosive fittings to ensure long and trouble-free  
operation in extreme location conditions. To ensure optimum  
performance throughout the life of the head Miller recommends  
regular cleaning.  
5.1 The DS10/DS20 fluid head provides adjustment for tilt and  
pan drag control (Fig 4.). Rotate clockwise to engage friction  
resistance, anticlockwise to return to fluid action.  
When the fluid head has been used in harsh environments (such  
as sand, mud or salt water spray), wipe over with a soft damp  
cloth as soon as possible. Use a soft brush to clean crevices.  
Remove and clean CAMERA PLATE.  
Note:The fluid drag plate system has been designed to suit  
most operating conditions. The friction drag adjustment should  
only be utilised when extra resistance is required.  
WARNING: Do not immerse a fluid head in any liquid.  
WARNING: Do not use stiff brushes, abrasives or solvents.  
Storage  
When storing for extended periods: clean fluid head and place in  
a safe, dry place, away from direct sunlight. The fluid heads can  
be stored horizontally or upright. However, it is not advisable to  
leave the head for extended periods with the tilt locked in an  
extreme position, either forward or backward.  
Fig 4  
Drag  
control  
knobs  
Maintenance  
With the exception of cleaning, the DS5/DS10/DS20 fluid head  
does not require additional maintenance. Miller recommends  
periodic servicing by a Miller Authorised Service Agent. Miller  
Authorised Service Agents must carry out all service and repair  
work. Failure to observe this requirement may void warranty.  
6
Technical Data  
Specifications – DS5/DS10/DS20 Fluid Head  
Description  
DS5 (#180)  
DS10 (#182)  
1.7 (3.7)  
DS20( #184)  
Weight - kg (lb)  
Payload Range - kg (lb)  
Pan/Tilt Drag  
1.6 (3.5)  
1.75 (3.9)  
0.5 - 2.5 (1.1 - 5.5)  
Fluid Drag plate system  
2.5 - 5.0 (5.5 - 11.0)  
5.0 - 10.0 (11.1 - 22.0)  
Fluid Drag plate system  
Fluid Drag plate  
system with friction boost.  
system with friction boost.  
Pan/Tilt Lock brake system  
Tilt Angle Range  
Calliper Disk Brake  
+90˚/-75˚  
Calliper Disk Brake  
+90˚/-75˚  
Calliper Disk Brake  
+90˚/-75˚  
Counterbalance System  
Position # 1 capacity - kg (lb)  
Position # 2 capacity - kg (lb)  
Camera Platform Type  
Single Position  
Up to 2.5 (5.5)  
-
Two Position  
Two Position  
Up to 2.5 (5.5)  
2.5 - 5.0 (5.5 - 11.0)  
2.5 - 5.0 (5.5 - 11.0)  
5.0 - 10.0 (11.0 - 22.0)  
Quick Release Sliding Camera  
Plate with 60 mm travel.  
Quick Release Sliding Camera  
Plate with 60 mm travel.  
Quick Release Sliding Camera  
Plate with 60 mm travel.  
Camera Plate  
Standard DS with  
1/4” + Pin Adapter Carriage  
Standard DS with  
1/4” + Pin Adapter Carriage  
Standard DS with  
1/4” + Pin Adapter Carriage  
1/4” and 3/8” screws  
Bubble Level  
Yes  
Yes  
Yes  
Mounting Base  
Handle  
75 mm ball levelling  
Standard Pan Handle  
-40˚/+65˚ (-40˚ / +149˚)  
75 mm ball levelling  
Standard Pan Handle  
-40˚/+65˚ (-40˚ / +149˚)  
75 mm ball levelling  
Standard Pan Handle  
-40˚/+65˚ (-40˚ / +149˚)  
Temperature Range - ˚C (˚F)  
7
Spare Parts  
Service, Sales & Support  
Miller Authorised Service Agents must carry out all service and repair  
work. Failure to observe this requirement may void warranty. It is  
advisable to notify Miller or a Miller Authorised Service Agent if a change  
of performance is observed as a result of dropping or rough usage. For  
your nearest authorised Miller sales or service centre, please visit our  
ITEM  
ITEM NO.  
DS5/DS10 Camera Plate (inc. #493 carriage)  
#490  
DS20 Camera Plate (inc. #493, 3/8” & 1/4” screws)  
1/4”– Pin carriage  
#489  
#493  
Camera Screw 1/4”  
P0036  
P0037  
#688  
Camera Screw 3/8”  
MILLER CAMERA SUPPORT (Australia)  
30 Hotham Parade, Artarmon, Sydney  
NSW 2064 Australia  
MILLER CAMERA SUPPORT LLC (USA)  
216 Little Falls Road, Cedar Grove  
New Jersey 07009-1231 USA  
Tel: (973) 857 8300  
Fixed Length Pan Handle  
Fixed Length Pan Handle & clamp  
Pan Handle Clamp  
#680  
Tel: +61 2 9439 6377  
Fax: +61 2 9438 2819  
Fax: (973) 857 8188  
P3436  
P2321  
Clamp Nut  
MILLER FLUID HEADS (Europe) LTD.  
Unit A2, Ford Lane Industrial Estate  
Ford Lane, Ford, West Sussex  
BN18 0DF United Kingdom  
MILLER TRIPODS Canada  
1055 Granville Street  
Vancouver BC V6Z1L4, Canada  
Tel: (604) 685 4654  
Warranty  
Miller offers a comprehensive parts and labour warranty with  
all it’s camera support products. For complete details please  
refer to the warranty card enclosed or contact your nearest  
Miller sales or service centre.  
Tel: +44 (0)1243 555 255  
Fax: (604) 685 5648  
Fax: +44(0)1243 555 001  
For information about the complete range of Miller camera  
support products, or to find the address of your nearest  
authorised Miller sales centre, please visit our website at  
D3573 - 2  
09/06  

PYLE Audio PLD144 User Manual
Pioneer XW DV515 User Manual
Pioneer XM SATELLITE DIGITAL TUNER GEX P910XM User Manual
Perlick 66134 3 User Manual
Oregon Scientific RM313PA User Manual
Olympus FFL 50 User Manual
Magnat Audio Xcess 216 User Manual
Laney Amplification Car Amplifier RBW100 User Manual
KVH Industries Azimuth 1000 Compass 01 0148 User Manual
Kenwood KCA R71FM User Manual