Metra Electronics 99 8214TG User Manual

INSTALLATION INSTRUCTIONS FOR PART 99-8214  
APPLICATIONS  
Toyota Tacoma 2005-2011  
99-8214TB  
99-8214TG  
KIT FEATURES  
• DIN Head Unit Provision With Pocket  
• ISO DIN Head Unit Provision With Pocket  
• Double DIN Head Unit Provision  
• Stacked ISO DIN Head Unit Provision  
• Painted And Textured To Match Factory Dash  
• Available In Two Colors:  
99-8214TB = BLACK, 99-8214TG = GRAY  
• Both kits are factory “golf ball” style  
textured.  
KIT COMPONENTS  
• A) Radio Housing • B) Radio Housing Brackets  
• C) Radio Housing Trim Panel • D) ISO Brackets  
• E) ISO Trim Plate • F) (4) #6 x 3/8” Phillips Pan Head Screws  
• G) (4) #8 X 3/8” Phillips Truss Head Screws • H) Double DIN Trim Plate • I) Clock/Hazard Switch Bracket  
E
B
A
I
G
F
C
D
H
WIRING AND ANTENNA CONNECTIONS (Sold Separately)  
Harness:  
• 70-1761 - Toyota harness 1987-up  
• TYTO-01 - Toyota amp interface harness 2003-up  
Antenna Adapter:  
• Not required  
TOOLS REQUIRED:  
Phillips Screwdriver • Small Flat Blade Screwdriver • Socket Wrench  
1-800-221-0932  
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION  
DASH DISASSEMBLY  
99-8214  
TOYOTA TACOMA 2005-2011  
A
1
Disconnect the negative battery  
terminal to prevent an accidental  
short circuit.  
TEXT  
PWR VOL  
2
3
4
Unclip and remove A/C control panel.  
(Figure A)  
SCAN  
Remove (4) 10 MM bolts securing  
radio. (Figure B)  
Unclip and remove entire panel  
including hazard switch and clock.  
(Figure C)  
5
6
Remove the left and right radio  
brackets from the radio chassis.  
(Figure D)  
B
Unclip and remove the clock/hazard  
switch assembly from the factory  
radio housing trim panel. (Figure E)  
Continue to Kit Preparation.  
E
C
TEXT  
PWR VOL  
D
SCAN  
1
KIT PREPARATION  
99-8214  
TACOMA 2005-2011  
(SKIP KIT PREPARATION WHEN INSTALLING DDIN RADIO)  
A
Attach the clock/hazard switch  
bracket to the radio housing using  
the (4) #6 x 3/8” Phillips pan head  
screws.  
WARNING:  
DO NOT OVERTIGHTEN SCREWS.  
1
2
Clip the clock/hazard switch  
assembly into the 99-8214 Radio  
Housing Trim Panel. (Figure A,B)  
Continue to Kit Assembly.  
PASSENGER  
PASSENGER  
H
M
INSERT CLOCK/HAZARD S  
WITCH ASSEMBLY  
FROM REAR OF 99-8214 R  
ADIO HOUSING TRIM PAN  
EL  
B
PAS  
P
ASSEN  
H
SENGE  
R
GER  
M
2
KIT ASSEMBLY  
99-8214  
TOYOTA TACOMA 2005-2011  
DIN HEAD UNIT PROVISION  
A
1
2
Attach the corresponding radio  
housing bracket to the radio housing  
using the included (4) #8 x 3/8”  
Slide the DIN cage into the Radio  
Housing and secure by bending the  
metal locking tabs down. (Figure B)  
3
4
Slide the aftermarket head unit into  
the cage and secure. (Figure C)  
B
Secure the Radio Housing into the  
dash using the factory hardware.  
Continue to Final Assembly.  
C
3
KIT ASSEMBLY  
99-8214  
TOYOTA TACOMA 2005-2011  
ISO DIN HEAD UNIT PROVISION  
A
1
Attach the corresponding radio  
housing bracket to the radio housing  
using the included (4) #8 x 3/8”  
Phillips truss head screws.(Figure A)  
2
3
Mount the ISO Brackets to the head  
unit with the screws supplied with  
the unit. (Figure B)  
Slide the head unit into the radio  
opening until the side clips engage.  
(Figure C)  
B
4
5
Snap the ISO Trim Plate into the  
Radio Housing. (Figure C)  
Secure the radio housing into the  
dash using the factory hardware.  
Continue to Final Assembly.  
C
4
KIT ASSEMBLY  
99-8214  
DOUBLE DIN HEAD UNIT PROVISION  
A
1
Slide the aftermarket radio unit into  
the factory brackets and secure the  
unit to the brackets using the  
screws supplied with the head unit.  
(Figure A)  
Secure the aftermarket radio unit  
and factory bracket assembly into  
the sub dash. (Figure B)  
2
3
Place the Double DIN trim plate into  
the back of the radio housing, then  
B
attach the clock/hazard switch brack-  
et assembly using the (4) #6 x 3/8”  
Phillips pan head screws. (Figure C)  
WARNING:  
DO NOT OVERTIGHTEN SCREWS.  
4
Clip the clock/hazard switch  
assembly into the 99-8214 Radio  
Housing Trim Panel. (Figure D)  
Continue to Final Assembly.  
D
C
REAR VIEW OF  
RADIO HOUSING  
REAR VIEW OF RADIO HOUSING  
DOUBLE DIN TRIM PLATE  
REMOVE  
REMOVE  
CLOCK/HAZARD SWITCH  
BRACKET ASSEMBLY  
CLOCK/HAZARD SWITCH  
BRACKET ASSEMBLY  
RESTORE  
RESTORE  
CLOCK/HAZARD SWITCH  
BRACKET ASSEMBLY  
CLOCK/HAZARD SWITCH  
BRACKET ASSEMBLY  
5
KIT ASSEMBLY  
99-8214  
STACKED ISO DIN HEAD UNIT PROVISION  
A
1
2
Slide the aftermarket radio units into  
the factory brackets and secure the  
unit to the brackets using the  
screws supplied with the head unit.  
(Figure A)  
Secure the aftermarket radio units  
and factory bracket assembly into  
the sub dash. (Figure B)  
3
Remove the (4) screws securing the  
clock/hazard switch bracket to the  
radio housing and remove the  
clock/hazard switch bracket  
assembly. (Figure C)  
B
4
Place the Double DIN trim plate into  
the radio housing and replace the  
clock/hazard switch/bracket assem-  
bly using the (4) #6 x 3/8” Phillips  
pan head screws. (Figure D)  
Continue to Final Assembly.  
C
D
REAR VIEW OF  
RADIO HOUSING  
REAR VIEW OF RADIO HOUSING  
DOUBLE DIN TRIM PLATE  
REMOVE  
REMOVE  
CLOCK/HAZARD SWITCH  
BRACKET ASSEMBLY  
CLOCK/HAZARD SWITCH  
BRACKET ASSEMBLY  
RESTORE  
RESTORE  
CLOCK/HAZARD SWITCH  
BRACKET ASSEMBLY  
CLOCK/HAZARD SWITCH  
BRACKET ASSEMBLY  
6
FINAL ASSEMBLY  
99-8214  
FINAL ASSEMBLY  
Locate the factory wiring harness in the dash and make the connection as shown.  
Metra recomends using the proper mating adapter and making the connections as  
shown. (Isolate and individually tape off the ends of any unused wires to prevent  
1
Re-connect the negative battery terminal and test the unit for proper operation.  
Reassemble radio and dash assemblies in reverse order of disassembly.  
2
3
FINAL WIRING CONNECTIONS  
Make wiring connections using the EIA color code chart shown below and the instructions included with the head  
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually  
tape off ends of any unused wires to prevent electrical short circuit.  
A
A)  
B)  
C)  
D)  
Strip wire ends back 1/2"  
Twist ends together  
Solder  
B
C
D
Tape  
METRA / EIA WIRING CODE  
12V Ignition / Acc . . . Red  
Right Front (+) . . . . . Gray  
12V Batt / Memory . . Yellow  
Ground . . . . . . . . . . . Black*  
Power Antenna . . . . . Blue  
Right Front (-). . . . . . Gray / Black  
Left Front (+) . . . . . . White  
Left Front (-). . . . . . . White / Black  
Right Rear (+). . . . . . Violet  
Amp Turn-On . . . . . . Blue / White  
Amp Ground . . . . . . . Black / White  
Illumination. . . . . . . . Orange  
Dimmer . . . . . . . . . . Orange / White  
Right Rear (-) . . . . . . Violet / Black  
Left Rear (+). . . . . . . Green  
Left Rear (-) . . . . . . . Green / Black  
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.  
All colors may not be present on all leads due to manufacturer’s specifications.  
7
99-8214  
NOTES  
8
99-8214  
NOTES  
9
99-8214 INSTRUCTIONS  
1-800-221-0932  
REV. 11/22/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-8214  

Rinnai E110CP User Manual
Panasonic AG HPX300P User Manual
Oster 3200 User Manual
Omega B2600 User Manual
Melissa 646 069 User Manual
Kramer Electronics Camcorder VP 790 User Manual
Korg MMA130 User Manual
Kodak PLAYTOUCH ZI10 User Manual
Kicker ZX3002 User Manual
JVC KD AV7100 User Manual