Metra Electronics 99 8100 User Manual

INST 8100  
KIT COMPONENTS  
4
Fig. A  
99-8100  
INSTALLATION  
INSTRUCTIONS  
Fig. B  
#2  
APPLICATIONS  
2-SHAFT HEAD UNITS: Snap the Faceplate onto the front of the Radio Housing. (For  
applications using Faceplate #2, cut and remove the bottom portion of the Faceplate). Slide  
the aftermarket head unit into the kit and secure with shaft nuts. (see Fig. A)  
CAR  
TOYOTA  
PAGE  
e  
4Runner 1984-88..........................................................................8  
Camry 1983-86.............................................................................1  
Celica 1982-85..............................................................................1  
Celica (GT/GTS) 1986-89...............................................................2  
Celica (ST) 1986-89.......................................................................2  
Celica 1990-93..............................................................................3  
Corolla (sport coupe/liftback) 1982-83.......................................... 3  
Corolla 1984-87............................................................................ 4  
Corolla (sedan/wagon-lower dash) 1988-93.................................. 4  
Corolla (sedan/wagon-upper dash) 1988-93.................................. 5  
Cressida 1985-87.......................................................................... 5  
Landcruiser 1982-87..................................................................... 6  
Landcruiser 1988-92..................................................................... 6  
MR2 1985-86................................................................................7  
MR2 1987-90................................................................................7  
Pickup 1984-88.............................................................................8  
Pickup (single DIN) 1989-91..........................................................8  
Pickup (double DIN) 1989-91........................................................ 9  
Supra 1983-85..............................................................................1  
Supra 1986.5-92...........................................................................9  
DIN HEAD UNITS: Cut and remove the shaft supports from the Faceplate and Radio  
Housing. (For applications using Faceplate #2, cut and remove the bottom portion of the  
Faceplate). Snap the Faceplate onto the front of the Housing. Slide the DIN cage into the kit  
and secure by bending the metal locking tabs down. Slide the aftermarket head unit into the  
cage until secure. (see Fig. B)  
(If an equalizer will be included, slide the unit into the back of the Radio Housing and secure.  
If an equalizer will NOT be included, snap theEqualizer Dummy Plateinto the opening).  
Equalizer  
Dummy Plate  
5
6
A
B
Celica 1990-93  
application  
shown  
Mounting Tabs #3  
C
D
Mounting Tabs #8  
(4) Phillips Pan-head  
Screws  
A) Strip wire ends back ½"  
B) Twist ends together  
C) Solder  
D) Tape  
TOOLS REQUIRED  
Locate the factory wiring harness in the  
dash. Metra recommends using the  
proper mating adaptor and making  
connections as shown. (Isolate and  
individually tape off the ends of any  
unused wires to prevent electrical short  
circuit).  
Re-connect the battery terminal and test the unit  
for proper operation. Mount the head unit/kit  
assembly to the sub-dash with those screws  
previously removed in step #1. (It may be  
necessary to trim the ends of the Mounting Tabs  
to provide proper clearance).  
Phillips screwdriver  
Cutting tool  
© COPYRIGHT 2001 METRA ELECTRONICS CORPORATION  
rev. 201202  
11  
TOYOTA Pickup (double DIN) 1989-91  
TOYOTA Celica (GT/GTS) 1986-89  
1
2
1
2
"D"  
"B"  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
(3) screws and (1) bolt securing the driver's  
side speaker panel and remove the panel.  
Remove (1) screw from the left side of the  
housing and unsnap the ignition cover.  
Remove the glove compartment assembly  
by removing (1) 10mm bolt from the bottom  
of the speaker panel and (3) screws from the  
right side of the housing. Remove the  
remaining (3) screws securing the radio trim  
bezel. Remove the screws securing the  
factoryheadunitanddisconnectthewiring.  
"B"  
"H"  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
(2) screws from the lower steering column  
panel and remove the panel. Remove (2)  
screws exposed on the dash trim bezel.  
Open the glove box and remove (2) screws  
exposed. Remove (2) screws from the  
ashtray cavity and (2) screws from the  
bracket. Remove (2) screws from each side  
of the dash trim bezel and unclip the bezel.  
Remove the screws securing the factory head  
unitanddisconnectthewiring.  
Slide Mounting Tabs #3 and #8 into slots  
"B" on Bracket Set #2. The Mounting Tabs,  
Brackets and Bracket slots can be identified  
by the stamped letter on each component.  
Skip to the Installation Instructions for ALL  
VEHICLESonPage#10.  
Slide Mounting Tabs #3 into slots "H" and  
"D" on Bracket Set #2. The Mounting Tabs,  
Brackets and Bracket slots can be identified  
by the stamped letter on each component.  
Skip to the Installation Instructions for ALL  
VEHICLESonPage#10.  
TOYOTA Celica (ST) 1986-89  
TOYOTA Supra 1986-92  
1
2
1
2
"C"  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
(2) screws from the lower steering column  
panel and remove the panel. Remove (2)  
screws exposed on the dash trim bezel.  
Open the glove box and remove (2) screws  
exposed. Remove (2) screws from the  
ashtray cavity and (2) screws from the  
bracket. Remove (2) screws from each side  
of the dash trim bezel and unclip the bezel.  
Remove the screws securing the factory head  
unitanddisconnectthewiring.  
"C"  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
the ashtray and (2) screws from the ashtray  
cavity. Remove (1) screw to the right of the  
steering column and (1) screw to the left of  
Slide Mounting Tabs #8 into slots "C" on  
Bracket Set #2. The Mounting Tabs,  
Brackets and Bracket slots can be identified  
by the stamped letter on each component.  
Skip to the Installation Instructions for ALL  
VEHICLESonPage#10.  
Locate the Mounting tabs on Radio  
Housing #1. (Brackets are NOT required  
for this vehicle). Skip to the Installation  
Instructions for ALL VEHICLES on Page  
#10.  
the gear shifter.  
Remove the screws  
securing the factory head unit and  
disconnect the wiring.  
9
2
TOYOTA Celica 1990-93  
TOYOTA Pickup 1984-88 / 4Runner 1984-88  
"J"  
1
2
2
1
"A"  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Pry up  
on the gear shifter trim panel and remove the  
panel. Remove (2) screws exposed on the  
bottom edge of the radio trim bezel. Unclip  
the bezel, and disconnect the ashtray and  
cigarette lighter wiring. Remove the screws  
securing the factory head unit and  
disconnect the wiring.  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
the ashtray and (3) screws from the ashtray  
bracket. Remove (1) screw from each side  
of the dash console and unclip the dash trim  
bezel. Remove the screws securing the  
factoryheadunitanddisconnectthewiring.  
"I"  
Slide Mounting Tabs #3 into slots "A" on  
Bracket Set #1.  
Brackets and Bracket slots can be identified  
by the stamped letter on each component.  
Skip to the Installation Instructions for ALL  
VEHICLES on Page #10.  
Slide Mounting Tabs #3 into slots "J" and  
"I" on Bracket Set #1. The Mounting Tabs,  
Brackets and Bracket slots can be identified  
by the stamped letter on each component.  
Skip to the Installation Instructions for ALL  
VEHICLESonPage#10.  
The Mounting Tabs,  
TOYOTA Pickup (single DIN) 1989-91  
TOYOTA Corolla (sport coupe/liftback) 1982-83  
1
2
"D"  
1
2
"B"  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
(3) screws and (1) bolt securing the driver's  
side speaker panel and remove the panel.  
Remove (1) screw from the left side of the  
housing and unsnap the ignition cover.  
Remove the glove compartment assembly  
by removing (1) 10mm bolt from the bottom  
of the speaker panel and (3) screws from the  
right side of the housing. Remove the  
remaining (3) screws securing the radio trim  
bezel. Remove the screws securing the  
factoryheadunitanddisconnectthewiring.  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
(2) screws from each side of the dash trim  
bezel and remove the bezel. Remove (4)  
screws securing the upper radio dummy  
covertothebezelandremove.  
"B"  
Slide Mounting Tabs #3 into slots "D" on  
Bracket Set #12. The Mounting Tabs,  
Brackets and Bracket slots can be identified  
by the stamped letter on each component.  
Skip to the Installation Instructions for ALL  
VEHICLESonPage#10.  
Slide Mounting Tabs #3 into slots "B" on  
Bracket Set #1. The Mounting Tabs,  
Brackets and Bracket slots can be identified  
by the stamped letter on each component.  
Skip to the Installation Instructions for ALL  
VEHICLESonPage#10.  
3
8
TOYOTA MR2 1985-86  
TOYOTA Corolla 1984-87  
"G"  
1
2
1
2
Fig. A  
"C"  
"F"  
"G"  
Fig.
"F"  
"C"  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
(2) Phillips screws above the climate  
controls. Unclip the lower edge of the radio  
trim bezel and remove. Remove the screws  
securing the factory head unit and  
disconnectthewiring.  
2DR/3DR MODELS: Slide Mounting Tabs  
#3 into slots "G" on Bracket Set #1. (see Fig.  
A).  
4DR/5DR MODELS: Slide Mounting Tabs  
#3 into slots "F" on Bracket Set #1. (see Fig.  
B).  
The Mounting Tabs, Brackets and Bracket  
slots can be identified by the stamped letter  
on each component. Skip to the Installation  
InstructionsforALLVEHICLESonPage#10.  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
(2) Phillips screws from each side of the  
Slide Mounting Tabs #3 into slots "C" on  
Bracket Set #12. The Mounting Tabs,  
Brackets and Bracket slots can be identified  
by the stamped letter on each component.  
Skip to the Installation Instructions for ALL  
VEHICLESonPage#10.  
radio trim bezel.  
Remove the bezel.  
Remove (4) screws securing the factory  
headunitanddisconnectthewiring.  
TOYOTA MR2 1987-90  
TOYOTA Corolla (sed/wag-lower dash) 1988-93  
1
2
1
2
"I"  
"F"  
"F"  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
(2) screws from the top of the dash trim bezel  
and remove the bezel. Remove (4) screws  
from the factory head unit (or coin tray  
dummypanel)anddisconnectthewiring.  
"I"  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
(1) screw to the right of the ignition switch.  
Remove (1) screw above the left speaker.  
Unclip the dash trim bezel (some force may  
be required). Remove the screws securing  
the factory head unit and disconnect the  
wiring.  
Slide Mounting Tabs #3 into slots "I" on  
Bracket Set #12. The Mounting Tabs,  
Brackets and Bracket slots can be identified  
by the stamped letter on each component.  
Skip to the Installation Instructions for ALL  
VEHICLESonPage#10.  
Slide Mounting Tabs #3 into slots "F" on  
Bracket Set #2. The Mounting Tabs,  
Brackets and Bracket slots can be identified  
by the stamped letter on each component.  
Skip to the Installation Instructions for ALL  
VEHICLESonPage#10.  
7
4
TOYOTA Corolla (sed/wag-upper dash) 1988-93  
TOYOTA Landcruiser 1982-87  
1
2
1
2
"A"  
"B"  
"B"  
"A"  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
(4) screws from the top edge of the dash trim  
bezel. Remove (2) screws below the radio  
opening. Remove (1) screw from the lower-  
left tab of the dash trim bezel (to the right of  
the a/c vent). Unclip the bezel. Remove the  
screws securing the factory head unit and  
disconnect the wiring.  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
(4) Phillips screws securing the factory head  
unitanddisconnectthewiring.  
Slide Mounting Tabs #8 into slots "A" on  
Bracket Set #12. The Mounting Tabs,  
Brackets and Bracket slots can be identified  
by the stamped letter on each component.  
Skip to the Installation Instructions for ALL  
VEHICLES on Page #10.  
Slide Mounting Tabs #3 and #8 into slots  
"B" on Bracket Set #12. The Mounting  
Tabs, Brackets and Bracket slots can be  
identified by the stamped letter on each  
component.  
Skip to the Installation  
Instructions for ALL VEHICLES on Page  
#10.  
TOYOTA Cressida 1985-87  
TOYOTA Landcruiser 1988-92  
1
2
1
2
"H"  
"C"  
"H"  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Unclip  
the climate control trim panel and remove (2)  
screws exposed. Remove (2) screws above  
the radio opening. Unclip the dash trim  
bezel, disconnect the wiring and remove the  
bezel. Remove (4) screws securing the  
factoryheadunitanddisconnectthewiring.  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
(3) screws from the lower edge of the climate  
control panel. Remove (8) screws from the  
perimeter of the dash trim bezel. Pull out on  
the lower edge of the bezel and remove.  
Remove the screws securing the factory  
head unit and disconnect the wiring.  
"C"  
Slide Mounting Tabs #3 into slots "C" on  
Bracket Set #1.  
Brackets and Bracket slots can be identified  
by the stamped letter on each component.  
Skip to the Installation Instructions for ALL  
VEHICLESonPage#10.  
Slide Mounting Tabs #3 into slots "H" on  
Bracket Set #1.  
Brackets and Bracket slots can be identified  
by the stamped letter on each component.  
Skip to the Installation Instructions for ALL  
VEHICLES on Page #10.  
The Mounting Tabs,  
The Mounting Tabs,  
5
6

ProMaster LED STUDIO VL306 User Manual
Planar Systems Car Video System PT1945RW User Manual
Pioneer DEH 2200UB User Manual
Panasonic AG DVX100BE User Manual
Olympus SP 600UZ User Manual
O'Brien SUPER BOUNCER 2101500 User Manual
Legacy Car Audio LA1838 User Manual
JVC XL MV558GD User Manual
JVC LYT1353 001B User Manual
JVC KS AX6700 User Manual