Metra Electronics 99 7875 User Manual

INSTALLATION INSTRUCTIONS FOR PART 99-7875/99-7875T  
APPLICATIONS  
Honda Accord 2008-2010  
(For Non-Navigation models with Dual Zone Climate controls)  
Honda Accord Crosstour 2010  
99-7875/99-7875T  
KIT FEATURES  
• Painted To Match Factory Dash  
99-7875=Charcoal, 99-7875T=Taupe  
• DIN Radio Provision with Pocket  
• ISO Mount Radio Provision with Pocket  
• Double DIN Radio Provision  
• Stacked ISO Mount Units Provision  
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets  
• E) Double DIN Trim Plate • F) Pocket  
C
B
D
WIRING AND ANTENNA CONNECTIONS (Sold Separately)  
A
Harness:  
• 70-1729 - Honda harness 2008-up  
• 70-1730 - Honda amp interface harness 2008-up  
Antenna Adapter:  
• 40-HD10 - Honda antenna adapter 2005-up  
F
E
TOOLS REQUIRED:  
Small Flat Blade Screwdriver/ Panel Removal Tool  
• Phillips Screwdriver • Cutting Tool  
1-800-221-0932  
© COPYRIGHT 2008-2010 METRA ELECTRONICS CORPORATION  
99-7875/99-7875T DASH DISASSEMBLY  
HONDA ACCORD 2008-10 / CROSSTOUR 2010  
Disconnect the negative battery ter-  
minal to prevent an accidental short  
circuit.  
1
2
3
4
A
Unclip and remove the trim panel  
from above the glove box at the right  
side of the factory radio. (Figure A)  
Unclip and remove the trim panel at  
the left side of the factory radio.  
(Figure B)  
B
Remove the (2) Phillips screws from  
the left and right side of the of the  
factory radio. (Figure C)  
5
6
Unclip and remove the top of the cen-  
ter console including the cup holders.  
(Figure D)  
Remove (2) Phillips screws at the bot-  
tom edge of the pocket assembly.  
(Figure E)  
C
Remove (2) Phillips screws facing up  
inside of the pocket below the factory  
radio. (Figure F)  
7
8
Unclip and remove the pocket assem-  
bly. (Figure G)  
Continue on page 2.  
D
E
1
99-7875/99-7875T DASH DISASSEMBLY  
HONDA ACCORD 2008-10 / CROSSTOUR 2010  
9
Remove (2) Phillips screws facing up  
on the bottom of the factory radio.  
F
G
H
I
(Figure H)  
10 Unclip the factory radio assembly.  
Unplug and remove the radio assem-  
bly. (Figure I)  
11 Remove (6) Phillips screws securing  
the climate controls to the factory  
radio assembly and remove the con-  
trols from the assembly. (Retain the  
screws and climate controls for re-  
use during kit preparation.)  
12 Remove (4) Phillips screws securing  
the a/c vents to the factory radio  
assembly and remove the a/c vent  
from the assembly. (Retain the  
screws and a/c vents for re-use dur-  
ing kit preparation.)  
13 Unclip and remove the hazard  
switch/passenger air bag light  
assembly. (Retain the hazard  
switch/passenger air bag light  
assembly for re-use during kit prepa-  
ration.)  
14 Remove (4) Phillips screws securing  
trim panel at the bottom edge of the  
factory radio assembly and remove  
the trim panel. (Retain the screws  
and trim panel for re-use during kit  
preparation.)  
15 Remove (9) clips from the back of the  
factory radio assembly. (Retain the  
clips for re-use during kit prepara-  
tion.)  
Continue to kit preparation.  
2
99-7875/99-7875T KIT PREPARATION  
HONDA ACCORD 2008-10 / CROSSTOUR 2010  
A
Snap the hazard switch/passenger air  
bag light assembly into the radio  
housing from front. (Figure A)  
1
2
Secure the a/c vents into the radio  
housing using the factory hardware  
from rear. (Figure B)  
3
4
Secure the climate controls into the  
radio housing using the factory hard-  
ware from rear. (Figure C)  
B
Secure the trim panel onto the radio  
housing using the factory hardware.  
(Figure D)  
5
Attach the clips to the back of the  
radio housing. (Figure E)  
Continue to kit assembly.  
E
C
D
3
99-7875/99-7875T KIT ASSEMBLY  
DIN MOUNT RADIO PROVISION WITH POCKET  
*Note: Refer also to the instructions included with the aftermarket radio.  
A
Slide the DIN cage into the Radio  
Housing and secure by bending the  
metal locking tabs outward. (Figure A)  
1
2
3
Slide the aftermarket radio into the  
DIN cage until it snaps into place.  
(Figure B)  
Snap the pocket into the radio housing.  
(Figure C)  
Continue to final assembly.  
B
C
4
99-7875/7875T KIT ASSEMBLY  
ISO MOUNT RADIO PROVISION WITH POCKET  
*Note: Refer also to the instructions included with the aftermarket radio.  
1
Mount the ISO Brackets to the radio  
using the screws supplied with the  
radio. (Figure A)  
2
3
4
Slide the radio into the Radio Housing  
until it snaps into place. (Figure B)  
Snap the Trim Plate onto the front of  
the Radio Housing. (Figure C)  
Snap the Pocket into the Radio  
Housing. (Figure C)  
Continue to final assembly.  
5
99-7875/99-7875T KIT ASSEMBLY  
DOUBLE DIN/STACKED ISO MOUNT UNITS PROVISION  
*Note: Refer also to the instructions included with the aftermarket radio.  
1
2
Cut and remove the center bar from  
the Radio Housing. (Figure A)  
Snap the Double DIN brackets to the  
inside edge of the Radio Housing.  
(Figure B)  
3
4
Slide the Double DIN or stacked ISO  
mount units into the bracket/radio  
housing assembly and secure the  
unit(s) to the assembly using the  
screws supplied with the unit(s).  
(Figure C)  
Snap the Double DIN trim plate onto  
the front of the Housing/Radio assem-  
bly. (Figure C)  
Continue to final assembly.  
6
99-7875/99-7875T FINAL ASSEMBLY  
FINAL ASSEMBLY  
A
B
(A) Strip wire ends back 1/2"  
B) Twist ends together  
C) Solder  
D) Tape  
C
D
Locate the factory wiring harness in the dash. Metra recommends using the  
proper mating adapter and making connections as shown. (Isolate and individ-  
ually tape off the ends of any unused wires to prevent electrical short circuit.)  
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.  
Reassemble radio and dash assemblies in reverse order of disassembly.  
FINAL WIRING CONNECTIONS  
Make wiring connections using the EIA color code chart shown below and the instructions included with the  
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and  
individually tape off ends of any unused wires to prevent electrical short circuit.  
METRA / EIA WIRING CODE  
12V Ignition / Acc. . . . . . . . . . Red  
Right Front (+) . . . . . . . . . . . . Gray  
12V Batt / Memory. . . . . . . . . Yellow  
Ground. . . . . . . . . . . . . . . . . . Black*  
Power Antenna. . . . . . . . . . . . Blue  
Right Front (-). . . . . . . . . . . . . Gray/ Black  
Left Front (+) . . . . . . . . . . . . . White  
Left Front (-). . . . . . . . . . . . . . White / Black  
Right Rear (+) . . . . . . . . . . . . Violet  
Amp Turn-On . . . . . . . . . . . . . Blue / White  
Amp Ground. . . . . . . . . . . . . . Black / White  
Illumination . . . . . . . . . . . . . . Orange  
Dimmer . . . . . . . . . . . . . . . . . Orange / White  
Right Rear (-) . . . . . . . . . . . . . Violet / Black  
Left Rear (+) . . . . . . . . . . . . . Green  
Left Rear (-) . . . . . . . . . . . . . . Green / Black  
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.  
All colors may not be present on all leads due to manufacturer’s specifications.  
7
99-7875/7875T  
NOTES  
8
99-7875/99-7875T  
NOTES  
9
99-7875/7875T INSTRUCTIONS  
1-800-221-0932  
REV. 04/21/10 © COPYRIGHT 2008-2010 METRA ELECTRONICS CORPORATION INST99-7875  

Planar Systems Car Video System PL180M User Manual
Philips Car Video System 241E+03 User Manual
Panasonic AW RP400N User Manual
Oster 133093 005 000 User Manual
Olympus FL EC 14 User Manual
Olympus CAMEDIA X 350 PT 021 User Manual
Nikon D40x User Manual
Listen Technologies Listen Soft Case LA 306 User Manual
Lanzar Car Audio HERITAGE HTG 434 User Manual
Lanzar Car Audio 7001D User Manual