Metra Electronics 99 7013 User Manual

INSTALLATION INSTRUCTIONS FOR PART 99-7013  
APPLICATIONS  
Mitsubishi Outlander  
2007-2010  
99-7013  
KIT FEATURES  
• DIN Radio Provision with Pocket  
• ISO Mount Radio Provision with Pocket  
• Double DIN Radio Provision  
• Stacked ISO Mount Units Provision  
KIT COMPONENTS  
A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets  
• E) Double DIN Trim Plate • F) Snap In Pocket  
Harness & Antenna Connections (sold seperately)  
70-7005 - Mitsubishi Harness 07-up  
B
A
C
E
F
D
TOOLS REQUIRED:  
Small Flat Blade Screwdriver/ Panel Removal Tool  
• Phillips Screwdriver • Socket Set  
1-800-221-0932  
© COPYRIGHT 2007-2010 METRA ELECTRONICS CORPORATION  
99-7013 DASH DISASSEMBLY  
MITSUBISHI OUTLANDER 2007-2010  
1
2
Disconnect the negative battery ter-  
minal to prevent an accidental short  
circuit.  
A
B
C
Unclip and remove the vents from the  
left and right side of the factory radio  
panel. (Figure A)  
3
4
Remove (2) Phillips screws securing  
the radio trim panel then unclip and  
remove the panel. (Figure B)  
Remove (4) Phillips screws securing  
the radio chassis. Unplug and remove  
the chassis. (Figure C)  
Continued on page 2.  
1
99-7013 DASH DISASSEMBLY  
MITSUBISHI OUTLANDER 2007-2010  
Remove (7) Phillips screws securing  
5
the hazard switch assembly to the  
back of the factory radio trim panel.  
D
Unplug the ribbon cable from the  
hazard switch assembly and remove  
assembly from panel from rear.  
(Retain the screws and switch  
assembly to be reused during kit  
preparation) (Figure D,E)  
REMOVE  
“9” PHILLIPS SCREWS  
(RETAIN SCREWS)  
6
Remove the labels from the front of  
the radio trim panel at each side of  
the hazard switch by pushing them  
out from behind the panel. (Retain the  
labels to be reused during kit prepa-  
E
ration) (Figure F)  
Continued to kit preparation.  
F
2
99-7013 KIT PREPARATION  
MITSUBISHI OUTLANDER 2007-2010  
5
Secure the hazard switch panel into the radio housing using the factory hardware  
removed previously and apply labels from the front of the factory radio trim panel to  
front of the Metra radio panel. (Figure A,B)  
Continue to kit assembly.  
A
B
3
99-7013 KIT ASSEMBLY  
DIN RADIO PROVISION WITH POCKET  
*Note: Refer also to the instructions included with the aftermarket radio.  
1
Slide the DIN cage into the Radio  
Housing and secure by bending the  
A
metal locking tabs outward. (Figure A)  
2
3
Slide the aftermarket radio into the  
cage until it snaps into place. (Figure B)  
Snap the pocket into the radio housing.  
(Figure C)  
Continue to final assembly.  
B
C
4
99-7013 KIT ASSEMBLY  
ISO MOUNT RADIO PROVISION WITH POCKET  
*Note: Refer also to the instructions included with the aftermarket radio.  
1
Mount the ISO Brackets to the after-  
market radio using the screws sup-  
A
plied with the radio. (Figure A)  
2
3
4
Slide the radio into the Radio Housing  
until it snaps into place. (Figure B)  
Snap the Trim Plate onto the front of  
the Radio Housing. (Figure C)  
Snap the pocket into the Radio  
Housing. (Figure D)  
B
Continue to final assembly.  
C
D
5
99-7013 KIT ASSEMBLY  
DOUBLE DIN/STACKED ISO UNITS PROVISION  
*Note: Refer also to the instructions included with the aftermarket radio.  
1
2
Cut and remove the center bar from  
the Radio Housing. (Figure A)  
A
Snap the Double DIN Brackets to the  
inside edge of the Radio Housing.  
(Figure B)  
3
4
Slide the Double DIN or stacked ISO  
unit(s) into the bracket/radio housing  
assembly and secure the Double DIN  
or stacked ISO unit(s) to the assembly  
using the screws supplied with the  
unit(s). (Figure C)  
B
Snap the Double DIN Trim Plate onto  
the front of the Radio Housing.  
(Figure C)  
Continue to final assembly.  
C
6
99-7013 FINAL ASSEMBLY  
FINAL ASSEMBLY  
A
B
(A) Strip wire ends back 1/2"  
B) Twist ends together  
C) Solder  
D) Tape  
C
D
Locate the factory wiring harness in the dash. Metra recommends using the  
proper mating adapter and making connections as shown. (Isolate and individually  
tape off the ends of any unused wires to prevent electrical short circuit.)  
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.  
Reassemble radio and dash assemblies in reverse order of disassembly.  
FINAL WIRING CONNECTIONS  
Make wiring connections using the EIA color code chart shown below and the instructions included with the head  
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually  
tape off ends of any unused wires to prevent electrical short circuit.  
METRA / EIA WIRING CODE  
12V Ignition / Acc. . . . . . . . . . Red  
Right Front (+) . . . . . . . . . . . . Gray  
12V Batt / Memory. . . . . . . . . Yellow  
Ground. . . . . . . . . . . . . . . . . . Black*  
Power Antenna. . . . . . . . . . . . Blue  
Right Front (-). . . . . . . . . . . . . Gray/ Black  
Left Front (+) . . . . . . . . . . . . . White  
Left Front (-). . . . . . . . . . . . . . White / Black  
Right Rear (+) . . . . . . . . . . . . Violet  
Amp Turn-On . . . . . . . . . . . . . Blue / White  
Amp Ground. . . . . . . . . . . . . . Black / White  
Illumination . . . . . . . . . . . . . . Orange  
Dimmer . . . . . . . . . . . . . . . . . Orange / White  
Right Rear (-) . . . . . . . . . . . . . Violet / Black  
Left Rear (+) . . . . . . . . . . . . . Green  
Left Rear (-) . . . . . . . . . . . . . . Green / Black  
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.  
All colors may not be present on all leads due to manufacturer’s specifications.  
7
99-7013  
NOTES  
8
99-7013  
NOTES  
9
99-7013 INSTRUCTIONS  
1-800-221-0932  
REV. 04/21/10 © COPYRIGHT 2007-2010 METRA ELECTRONICS CORPORATION INST99-7013  

Pioneer Speaker DEH P5800MP User Manual
Pioneer AVIC 9DVD User Manual
Panasonic DVC20 User Manual
Oster Blender OSTERIZER CLASSIC BLENDER User Manual
Kicker KS400 User Manual
Kenwood eXcelon KDC X994 User Manual
Kenwood DDX52RY User Manual
Kenmore 5EW175 User Manual
K2 Bike K013016 User Manual
JVC KD A815 User Manual