Magnavox MBP1100 Blu ray Disc Player MBP1100 User Manual

Owner’s Manual  
MBP1100/F7  
Blu-ray Disc Player  
Read your Owner’s Manual first for  
quick tips that make using your  
Magnavox product more enjoyable.  
If you have read assistance,  
you may access our online help at  
or call  
1-800-605-8610  
while with your product  
(and Model / Serial number)  
© 2009 Funai Electric Co., Ltd.  
INTRODUCTION  
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.  
WARNING: Batteries (Battery pack or battery installed) shall not be exposed to excessive heat such as sunshine, fire, or the like.  
LASER SAFETY  
This apparatus employs a laser. Only a qualified service person should remove the cover or attempt to service this  
apparatus, due to possible eye injury.  
CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may  
result in hazardous radiation exposure.  
CAUTION: Visible and invisible laser radiation when open and interlocks defeated. Do not stare into beam.  
LOCATION: Inside, near the deck mechanism.  
IMPORTANT COPYRIGHT INFORMATION  
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited. This product incorporates  
copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this  
copyright protection technology must be authorized by Macrovision, and is intended for home and other limited  
viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.  
Do not place the unit on the furniture that is capable of being tilted by a child and an adult leaning, pulling, standing  
or climbing on it. A falling unit can cause serious injury or even death.  
To Avoid the Hazards of Electrical Shock and Fire  
• Do not handle the AC power cord with wet hands.  
• Do not pull on the AC power cord when disconnecting it from an AC outlet. Grasp it by the plug.  
• Do not put your fingers or objects into the unit.  
Location and Handling  
• Do not install the unit in direct sunlight, near strong magnetic fields, or in a place subject to dust or strong vibration.  
• Avoid a place with drastic temperature changes.  
• Install the unit in a horizontal and stable position. Do not place anything directly on top or bottom of the unit.  
Depending on your external devices, noise or disturbance of the picture and/or sound may be generated if the unit is  
placed too close to them. In this case, please ensure enough space between the external devices and the unit.  
• Depending on the environment, the temperature of this unit may increase slightly. This is not a malfunction.  
Be sure to remove the disc and unplug the AC power cord from the outlet before carrying the unit.  
Dew Condensation Warning  
• Dew condensation may form inside the unit in the following conditions. If so, do not use this unit at least for a few  
hours until its inside gets dry.  
- The unit is moved from a cold place to a warm place.  
- Under conditions of high humidity.  
- After heating a cold room.  
*
Note about Recycling  
• This unit’s packaging materials are recyclable and can be reused. Please dispose of any materials in  
accordance with your local recycling regulations.  
• Batteries should never be thrown away or incinerated but disposed of in accordance with your local  
regulations concerning chemical wastes.  
Notice for Progressive Scan Output  
• Consumers should note that not all high definition television sets are fully compatible with this product and may  
cause artifacts to be displayed in the picture. In case of picture problems with 525(480) progressive scan output,  
it is recommended that the user switch the connection to the ‘standard definition’ output. If there are questions  
regarding your TV set compatibility with this 525p(480p) BD/DVD player, please contact our customer service center.  
EN  
3
INTRODUCTION  
Contents  
INTRODUCTION  
FUNCTION SETUP  
Safety Instructions ........................................................................2  
Supplied Accessories ...................................................................5  
Trademark Information...............................................................5  
Features ............................................................................................6  
Symbols Used in this Manual....................................................6  
Front Panel.......................................................................................7  
Rear Panel.........................................................................................7  
Remote Control..............................................................................8  
Using the Setup Menu ..............................................................29  
Quick..........................................................................................29  
Custom .....................................................................................30  
Language............................................................................. 31  
Video ..................................................................................... 32  
Audio..................................................................................... 34  
Parental ................................................................................ 39  
Others.................................................................................... 40  
Initialize ....................................................................................44  
CONNECTIONS  
Connection to the TV................................................................ 10  
Connection to an Audio System........................................... 12  
Finding the Video Channel on Your TV.............................. 13  
OTHERS  
Troubleshooting..........................................................................45  
Glossary ..........................................................................................46  
Language Code List....................................................................47  
Maintenance.................................................................................49  
LIMITED WARRANTY .................................................back cover  
PLAYBACK  
Information on Playback.......................................................... 14  
How to Insert a Disc................................................................... 17  
Reading the SD Memory Card ............................................... 17  
Selecting the Media Mode...................................................... 18  
Playing Back (BD / DVD)........................................................... 19  
Playing Back (Audio CD / JPEG Files)................................... 20  
Kodak Picture CD........................................................................ 21  
Fast Forward / Fast Reverse.................................................... 22  
Slow Forward Playback ............................................................ 22  
Step by Step Playback .............................................................. 22  
Repeat Playback.......................................................................... 22  
Program Playback ...................................................................... 23  
Random Playback....................................................................... 24  
Rapid Playback ............................................................................ 24  
Adjusting the Picture ................................................................ 24  
Virtual Surround.......................................................................... 25  
PIP (BONUSVIEW) Setting........................................................ 25  
Camera Angle .............................................................................. 25  
Search............................................................................................. 26  
Switching Subtitles.................................................................... 27  
Switching Audio Soundtrack ................................................. 27  
Setting the BD Audio Mode.................................................... 28  
4
EN  
INTRODUCTION  
Supplied Accessories  
Owner’s Manual  
remote control × 1  
(NB950UD/NB900UD)  
AAA (1.5V) battery × 2  
RCA audio / video cables  
(WPZ0102TM018 /  
WPZ0102LTE01)  
owner’s manual (EN/ES/FR)  
(1VMN28573 /1VMN28574 /  
1VMN28575)  
quick start guide (EN/ES/FR)  
(1VMN28576 / 1VMN28577 /  
1VMN28578)  
Trademark Information  
“BONUSVIEW” is trademark of Blu-ray Disc Association.  
HDMI, the HDMI logo and High-Definition Multimedia  
Interface are trademarks or registered trademarks of HDMI  
Licensing LLC.  
Manufactured under license from Dolby Laboratories.  
Dolby and the double-D symbol are trademarks of Dolby  
Laboratories.  
Java and all other Java trademarks and logos are  
trademarks or registered trademarks of Sun Microsystems,  
Inc. in the United States and / or other countries.  
Manufactured under license under U.S. Patent #’s  
:
5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 &  
other U.S. and worldwide patents issued & pending. DTS is  
a registered trademark and the DTS logos, Symbol, DTS-HD  
and DTS-HD Advanced Digital Out are trademarks of DTS,  
Inc. © 1996-2008 DTS, Inc. All Rights Reserved.  
Products that have earned ENERGY STAR® are designed to  
protect the environment through superior energy  
efficiency.  
“Blu-ray Disc” and  
are trademarks.  
is trademark of Eastman Kodak Company.  
is a trademark of DVD Format/Logo Licensing  
Corporation.  
© 2009 Funai Electric Co., Ltd.  
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,  
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written consent  
of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly  
prohibited.  
Information in this document is subject to change without notice. Funai reserves the right to change the content herein  
without the obligation to notify any person or organization of such changes.  
with the  
design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the  
express written consent of Funai. All other trademarks used herein remain the exclusive property of their respective  
owners. Nothing contained in this manual should be construed as granting, by implication or otherwise, any license or  
right to use any of the trademarks displayed herein. Misuse of any trademarks or any other content in this manual is  
strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law.  
EN  
5
INTRODUCTION  
Easy and simple connection to your HDTV via  
HDMI  
Features  
Full high-definition video playback  
Connect this unit to your HDTV with one single HDMI (High-  
Definition Multimedia Interface) cable. It is recommended to  
use a High Speed HDMI Cable for better compatibility. The  
high definition video output signal will be transferred to your  
HDTV without conversion to analog signals, so you will get  
excellent picture and sound quality, completely free from  
noise.  
Watch movies in the highest picture quality available for your  
HDTV. This unit offers full high-definition video playback up to  
1080p resolution for an amazing viewing experience. A highly  
detailed picture and increased sharpness delivers a more true-  
to-life picture.  
Upconvert DVD for enhanced picture quality  
Your current DVD will look even better than before thanks to  
video upconversion. Upconversion will increase the  
resolution of standard definition DVD to high definition up to  
1080p over an HDMI connection. The picture will be less  
jagged and more realistic for a near high-definition  
experience.  
Thanks to other multiple outputs, you can also easily connect  
to your home theater system or amplifier.  
HDMI Deep Color  
Deep Color reduces the posterization effect of the playback  
image. Refer to “HDMI Deep Color” in “FUNCTION SETUP” on  
page 32.  
HDMI CEC (Consumer Electronics Control)  
Enjoy your content on different kinds of media  
This unit supports HDMI CEC, which allows integrated system  
control over HDMI and is part of the HDMI standard.  
This function may not work properly on some devices.  
Full backwards compatibility with DVD, CD and SD card  
ensures that you can continue to enjoy your current audio-  
video collection. Additionally, you can view JPEG images.  
HDMI 1080p24 output (BD only)  
Listen to the rich multi-channel surround sound  
Multi-channel surround sound, which recognizes real-to-life  
sound and makes you feel like you are really there.  
This unit is equipped with a feature which can provide the  
smooth movement in the playback of film originated material  
with the frame rate of 24 frames per second with progressive  
scan. (Available only when the TV is connected by an HDMI  
cable and compatible with 1080p24 frame input.)  
Refer to “HDMI Video Resolution” in “FUNCTION SETUP” on  
page 32.  
PIP (BONUSVIEW)  
Some BD-videos have the PIP function which enables you to  
display the secondary video in the primary video. You can call  
up the secondary video by pressing [MODE] whenever the  
scene contains the secondary video.  
Copyright protection system  
To play back the digital video images of a BD / DVD via an  
HDMI connection, it is necessary that both the unit and the  
TV (or an AV amplifier) support a copyright protection  
system called HDCP (high-bandwidth digital content  
protection system). HDCP is copy protection technology  
that comprises data encryption and authentication of the  
connected AV device. This unit supports HDCP. Please read  
the operating instructions of your TV (or AV amplifier) for  
more information.  
Pop-up menu  
Some BD-video have pop-up menu which is a navigation  
menu that can be called up and be operated on the TV screen  
without interrupting the playback. You can call up the pop-up  
menu by pressing [POP MENU / MENU]. Contents in the  
pop-up menu vary depending on the disc.  
Rapid playback  
Playback in slightly faster speed while keeping the sound  
output.  
Rapid playback is available only on discs recorded in the  
Dolby Digital format.  
Symbols Used in this Manual  
To specify for which media type each function is, we put the  
Playing back the contents in SD Memory Card  
You can play back JPEGs stored in an SD Memory Card.  
You can store picture-in-picture commentary, subtitles or  
other extras for BD-ROM Profile 1 ver.1.1 files in an SD Memory  
Card and play back with the BD-video.  
following symbols at the beginning of each item to operate.  
Symbol  
Description  
Description refers to BD-video and BD-RE  
(ver.2.1) / BD-R (ver.1.1/1.2/1.3) recorded in  
BDMV format  
Description refers to DVD-video  
Description refers to audio CD / DTS-CD  
Description refers to BD-RE/-R, DVD, CD-RW/-R  
and SD Memory Card with JPEG files  
If you do not find any of the symbols listed above under the  
function heading, the operation is applicable to all media.  
6
EN  
INTRODUCTION  
Front Panel  
1
2*  
3 4  
5
6* 7 8 9  
OPEN/  
CLOSE  
DISC IN  
SD card  
10  
(*) The unit can also be turned on by pressing these buttons.  
1. Disc tray  
• Place a disc when opening the disc tray.  
2. A OPEN/CLOSE button*  
• Press to open or close the disc tray.  
3. DISC IN indicator  
• This indicator lights up in blue when a disc is in this  
unit.  
4. Infrared sensor window  
• Receive signals from your remote control so that you  
can control the unit from a distance.  
5. C STOP button  
• Press to stop playback.  
6. B PLAY button*  
7. PLAY indicator  
• This indicator lights up in green when discs or SD  
card play back.  
8. STANDBY-ON indicator  
• This indicator lights up in red when the power is in  
the standby mode.  
9. Q STANDBY-ON button  
• Press to turn on the unit, or to turn the unit into the  
standby mode. (To completely turn off the unit, you  
must unplug the AC power cord.)  
• Press and hold for 10 seconds to shut down the unit.  
10. SD card slot  
• Insert an SD Memory Card and play back the  
contents in it.  
• Press to start or resume playback.  
Rear Panel  
3
4
2
1
Y
PR/CR  
L
HDMIOUT  
PB/CB  
COAXIAL  
R
DIGITAL OUT  
AUDIO  
OUT  
VIDEO  
OUT  
COMPONENT  
VIDEO OUT  
PCM/BITSTREAM  
5
6
1. AC power cord  
5. DIGITAL OUT (COAXIAL) jack  
• Connect to a standard AC outlet to supply power to  
this unit.  
• Unplug this cord from the AC outlet to completely  
• Use to connect an AV receiver / amplifier, Dolby  
Digital / DTS decoder or other device with a digital  
audio coaxial input jack with a digital audio RCA  
cable.  
turn off the unit.  
2. HDMI OUT jack  
6. VIDEO OUT jack  
• Use to connect a TV with an HDMI compatible port  
• Use to connect a TV, an AV receiver or other device  
with an RCA video cable.  
with an HDMI cable.  
3. AUDIO OUT jacks  
• Use to connect a TV, an AV receiver / amplifier or  
other device with an RCA audio cable.  
Note  
• Do not touch the inner pins of the jacks on the rear  
panel. Electrostatic discharge may cause permanent  
damage to the unit.  
4. COMPONENT VIDEO OUT jacks  
• Use to connect a TV with component video inputs  
with an RCA component video cable.  
• This unit does not have the RF modulator.  
EN  
7
INTRODUCTION  
Remote Control  
12. REPEAT button  
• Press to toggle between various repeat modes.  
13. OPEN/CLOSE A button*  
• Press to open or close the disc tray.  
14. POP MENU / MENU button  
• Press to display the pop-up menu / disc menu.  
15. OK button  
• Press to confirm or select menu items.  
16. RETURN button  
• Press to return to the previously displayed menu  
screen.  
17. D (forward) button  
• During playback, press to fast forward the playback.  
• In pause mode, press to slow forward the playback.  
18. G (skip) button  
• During playback, press to skip to the next title,  
chapter, track or file.  
19. F (pause) button  
1
2
13*  
14  
3
4
5
15  
16  
17  
18  
6
7*  
8
9
19  
• Press to pause playback.  
20  
21  
22  
23  
• When playback is in pause mode, press repeatedly  
to forward the playback step by step.  
20. DISPLAY button  
10  
• Press to display the on-screen display menu.  
21. ANGLE button  
• Press to access various camera angles on the disc.  
• Press to rotate the JPEG files clockwise by 90 degrees.  
22. SUBTITLE button  
11  
12  
24  
25  
• Press to display the subtitle menu.  
23. AUDIO button  
(*) The unit can also be turned on by pressing these buttons.  
• Press to display the audio menu.  
24. MODE button  
1. STANDBY-ON Q button  
• Press to turn on the unit, or to turn the unit into the  
standby mode. (To completely turn off the unit, you  
must unplug the AC power cord.)  
• During BD or DVD playback, press to display the  
setting for the rapid playback and the picture  
adjustment.  
2. RED / GREEN / BLUE / YELLOW button  
• During BD, DVD and CD playback, press to display  
the setting for the virtual surround.  
• Press to select items on some BD menus.  
• When file list / thumbnail list is shown, press to  
switch between pages.  
• During BD playback, press to turn the picture-in-  
picture feature on or off (only applicable to BD-video  
which supports the PIP function).  
3. TOP MENU button  
• Press to display the top menu.  
4. K / L / s / B buttons  
• Press to select items or settings.  
5. SETUP button  
• Press to display the setup menu.  
6. E (reverse) button  
• During playback, press to fast reverse the playback.  
7. B (play) button*  
• Press to start playback or resume playback.  
8. H (skip) button  
• During the JPEG playback, press to display menus  
for changing the visual effect for switching the  
image or changing the size of the image.  
• In stop mode with BD inserted, press to display a  
menu for setting the BD audio mode.  
• In stop mode with audio CD or JPEG files inserted, press  
to display menus for program and random playback.  
25. CLEAR button  
• Press to clear the information once entered or to  
cancel the programming for audio CD, etc.  
• During playback, press once to return to the  
beginning of the current title, chapter or track.  
• During playback, press twice to return to the  
previous title, chapter or track.  
• During the JPEG playback, press to return to the  
previous file.  
9. C (stop) button  
• Press to stop playback.  
10. Number buttons  
• Press to enter the title, chapter, track or file number.  
• Press to enter values in the input field.  
11. SEARCH button  
• Press to display the search menu.  
8
EN  
INTRODUCTION  
Installing the Batteries in the Remote Control  
Using a Remote Control  
Install AAA (1.5V) battery × 2 matching the polarity  
indicated inside battery compartment of the remote  
control.  
Keep in mind the following when using the remote  
control:  
• Make sure that there are no obstacles between the  
remote control and the infrared sensor window on the  
unit.  
1) Open the cover.  
• Remote operation may become unreliable if strong  
sunlight or fluorescent light is shining on the infrared  
sensor window of the unit.  
2
• Remote control for different devices can interfere with  
each other. Avoid using remote control for other device  
located close to the unit.  
• Replace the batteries when you notice a fall off in the  
operating range of the remote control.  
• The maximum operable ranges from the unit are as  
follows.  
1
- Line of sight: approx. 23 feet (7 m)  
e  
o  
o  
-
Either side of the center: approx. 16 feet (5 m) within 30°  
- Above: approx. 16 feet (5 m) within 15°  
- Below: approx. 10 feet (3 m) within 30°  
2) Insert batteries.  
OPEN/  
CLOSE  
DISC IN  
SD card  
30˚  
30˚  
16 feet  
(5 m)  
23 feet  
(7 m)  
16 feet  
(5 m)  
Make sure to match + and - on the batteries to the  
marks indicated in the battery compartment.  
3) Close the cover.  
2
1
Note  
Incorrect use of batteries can result in hazards such  
as leakage and bursting. Please observe the  
following:  
• Do not mix new and old batteries together.  
• Do not use different kinds of batteries together.  
Although they may look similar, different batteries  
may have different voltages.  
• Make sure that the + and - ends of each battery  
match the indications in the battery compartment.  
• Remove batteries from battery compartment that  
are not going to be used for a month or more.  
• When disposing of used batteries, please comply  
with governmental regulations or environmental  
public rules that apply in your country or area. (Refer  
to page 3.)  
• Do not recharge, short-circuit, heat, burn or  
disassemble batteries.  
EN  
9
CONNECTIONS  
Connection to the TV  
Choose the appropriate connection, then proceed to the corresponding  
instruction (A, B or C) on the next page.  
1
(Supports up to 1080i / 1080p, 1080p24 resolution.)  
Best  
Your TV  
HDMI IN  
Go To  
High  
Definition  
TV  
HDMI cable  
Video  
Audio  
A
B
C
No analog audio connection required.  
No supplied cables are used in this connection:  
Please purchase the necessary cables at your local store.  
High Speed HDMI Cable (also known as HDMI category 2 cable) is recommended for the better compatibility.  
(Supports up to 1080i resolution.)  
Better  
COMPONENT  
VIDEO IN  
Y
PB/CB  
RCA component video cable  
Your TV  
High  
Video  
Go To  
PR/CR  
Definition  
TV  
+
L
RCA audio cable  
Audio  
AUDIO IN  
R
Supplied cables used in this connection are as follows:  
• RCA audio cable (L/R) x 1  
Please purchase the rest of the necessary cables at your local store.  
(Supports only 480i resolution.)  
Basic  
VIDEO IN  
RCA video cable  
Your TV  
Video  
Go To  
Standard  
Definition  
TV  
L
+
RCA audio cable  
AUDIO IN  
R
Audio  
• Connect this unit directly to the TV. If the RCA audio / video cables are connected to a VCR, pictures may be distorted  
due to the copy right protection system.  
Supplied cables used in this connection are as follows:  
• RCA audio cable (L/R) x1  
• RCA video cable x1  
10  
EN  
CONNECTIONS  
Connect the cables by following the descriptions below.  
2
HDMI Video / Audio Connection  
Your TV  
9
0
2ꢀ#2  
"ꢀ#"  
,
A
($-)/54  
0
#/!8)!,  
2
$)')4!, /54  
!5$)/  
/54  
6)$%/  
/54  
#/-0/.%.4  
6)$%/ /54  
0#-")4342%!-  
HDMI IN  
HDMI cable  
Note  
• Do not tilt the connector when inserting it into the HDMI jack, and make sure the shapes of the jack and the  
connector are matched.  
• When using HDCP-incompatible TV, the image will not be viewed properly.  
Not displayed the picture on the TV screen ...  
The indicators blink under the following conditions.  
• When the connected device does not support HDCP.  
• When the connected device is recognized as an HDCP incompatible by HDMI SRM.  
• When the connected device supports HDCP but cannot be recognized as an HDCP compatible for some reason.  
The indicators blink as follows for 30 seconds.  
DISC IN  
Component Video + Standard Audio Connection  
Your TV  
9
02ꢀ#2  
,
($-)/54  
0"ꢀ#"  
#/!8)!,  
2
B
$)')4!, /54  
!5$)/  
/54  
6)$%/  
/54  
#/-0/.%.4  
6)$%/ /54  
0#-")4342%!-  
RCA  
component  
video cable  
COMPONENT  
VIDEO IN  
Y
Y
P
R/CR  
B/CB  
L
PR/CR  
PB/CB  
L
P
AUDIO IN  
R
R
AUDIO  
OUT  
COMPONENT  
VIDEO OUT  
RCA audio cable  
Standard Video + Standard Audio Connection  
Your TV  
C
9
0
2ꢀ#2  
"ꢀ#"  
,
($-)/54  
0
#/!8)!,  
2
$)')4!, /54  
!5$)/  
/54  
6)$%/  
/54  
#/-0/.%.4  
6)$%/ /54  
0#-")4342%!-  
L
L
VIDEO IN  
AUDIO IN  
RCA video cable  
RCA audio cable  
R
R
AUDIO  
OUT  
VIDEO  
OUT  
EN  
11  
CONNECTIONS  
Connection to an Audio System  
• When you change the connections, all devices should be turned off.  
• Refer to the manual accompanying external devices for more information.  
2-Channel Analog Audio Connection  
stereo system  
Digital Audio Connection  
AV receiver / amplifier  
audio  
AUDIO IN  
R
L
DIGITAL AUDIO INPUT  
COAXIAL  
digital audio coaxial  
input jack  
Analog audio input jacks  
digital audio  
RCA cable  
RCA audio cable  
L
this unit  
Y
Y
P
R
B
L
L
HDMIOUT  
HDMIOUT  
P
COAXIAL  
R
COAXIAL  
R
COAXIAL  
DIGITAL OUT  
AUDIO  
OUT  
VIDEO  
OUT  
DIGITAL OUT  
AUDIO  
OUT  
VIDEO  
OUT  
COMP
VIDE
PCM/BITSTREAM  
PCM/BITSTREAM  
DIGITAL OUT  
PCM/BITSTREAM  
R
AUDIO  
OUT  
AUDIO OUT  
DIGITAL OUT (COAXIAL)  
To set up “Digital Out”, refer to page 36.  
HDMI Audio Connection  
audio  
AV receiver / amplifier with an HDMI input jack  
this unit  
HDMI IN  
Y
P
R/CR  
B/CB  
HDMI cable  
L
HDMIOUT  
P
COAXIAL  
R
DIGITAL OUT  
AUDIO  
OUT  
VIDEO  
OUT  
COMPONENT  
VIDEO OUT  
PCM/BITSTREAM  
To set up “HDMI Audio Out”, refer to pages 35 and 34.  
Supplied cables used in this connections are as follows:  
• RCA audio cable (L/R) x 1  
Please purchase the rest of the necessary cables at your local store.  
12  
EN  
CONNECTIONS  
After you have completed all the connections, you must find the correct video channel (external input channel) on your TV.  
Finding the Video Channel on Your TV  
After you have made all the necessary connections, press [STANDBY-ON Q] to turn  
on the unit.  
1
Turn on your TV.  
2
3
Press the button on the TV’s remote control that accesses the external input  
channel. It may be labeled “SOURCE”, “AV” or “SELECT” (refer to your TV’s user  
manual).  
Note  
• If the TV is connected by an HDMI cable, it may take a while for the opening picture to come up.  
EN  
13  
PLAYBACK  
Information on Playback  
Before you start playing back a disc, read the following information.  
Readable cards  
Playable files / data  
Playable Discs and Files  
SD Memory Card (8 MB - 2 GB)  
SDHC Memory Card (4 GB - 8 GB)  
miniSD Card (8 MB - 2 GB)  
JPEG, picture-in-picture  
commentary, subtitles or  
other extras for BD-ROM  
Profile 1 ver.1.1  
This unit is compatible to play back the following discs / files.  
To play back a disc / file, make sure that it meets the  
requirements for region codes and color systems as  
described below. You can play back discs that have the  
following logos.  
microSD Card (8 MB - 2 GB)  
Other disc types are not guaranteed to play back.  
Note for SD Memory Cards  
• This unit supports SD Memory Card with FAT12/  
FAT16 file system, and SDHC Memory Card with  
FAT32 file system.  
Playable discs  
Logos  
Blu-ray Disc  
• This unit does not support NTFS file system.  
• This unit may not read the SD Memory Cards  
formatted on a computer. If that is the case, please  
reformat the SD Memory Cards in this unit and try  
again.  
- BD-video (single / dual layer)  
- BD-RE ver. 2.1 (single / dual layer)  
(Recorded in BDMV format)  
- BD-R ver. 1.1 / 1.2 / 1.3 (single / dual  
layer) (Recorded in BDMV format)  
(Unclosed discs may not be played  
back.)  
• This unit does not support miniSDHC and microSDHC  
Memory Card.  
• For miniSD Card and microSD Card, the adapter is  
necessary.  
DVD-video  
DVD-RW  
miniSD Card  
microSD Card  
adapter  
adapter  
miniSD Card  
microSD  
Card  
• Portions of this product are protected under  
copyright law and are provided under license by  
ARIS / SOLANA / 4C.  
DVD-R  
• Please keep the SD Memory Cards in their cases when  
you are not using them.  
CD-DA (audio CD)  
CD-RW  
• Do not try to open or modify the card.  
• Do not touch the terminal surface with your fingers or  
any metals.  
• Do not attach additional labels or stickers to cards.  
• Do not remove the label of the SD Memory Cards.  
• This unit recognizes up to 8 characters of file name in  
the SD Memory Card. Characters after 8th will not be  
displayed.  
CD-R  
Kodak Picture CD  
DTS-CD  
Unplayable Discs and Files  
The following discs will not be played back in this unit.  
• CD-ROM  
• DVD-RAM  
• DVD-audio  
• HD DVD  
• CD-I (compact disc-interactive)  
• VSD (video single disc)  
• Video CD  
-
• SVCD  
Playable files  
Media  
• Unfinalized disc  
• BD-RE (ver.1.0)  
BD-RE/-R, DVD, CD-RW/-R,  
SD Memory Card (including SDHC),  
miniSD Card, microSD Card  
JPEG  
• BD-RE (ver.2.1) (Recorded in BDAV format)  
• BD-R (ver.1.1 / 1.2 / 1.3) (Recorded in BDAV format)  
• DVD / CD / SD Memory Card contains MP3, Windows  
Media™ Audio and DivX® files.  
• DVD-RW/-R recorded in non compatible recording  
format.  
• Super Audio CD - Only the sound on the CD layer can be  
heard. The sound on the high-density Super Audio CD  
layer cannot be heard.  
• Playability of dual discs are not guaranteed.  
14  
EN  
PLAYBACK  
Color Systems  
On-Screen Display  
BD-video and DVD-video are recorded in different color  
systems throughout the world. The most common color  
system is NTSC (which is used primarily in the United  
States and Canada).  
This unit employs NTSC color system, so the disc you play  
back must be recorded in the NTSC system. You cannot  
play back the disc recorded in other color systems.  
You can check information about the current disc by  
pressing [DISPLAY].  
To call the on-screen display menu, press [DISPLAY]  
during playback. Every time you press [DISPLAY], the  
information changes. Depending on the media, available  
information varies.  
Region Codes  
off A Title / Chapter information  
A Title information (elapsed time)  
A Title information (remaining time)  
A Audio format information A off  
BD-video  
This unit has been designed to play back  
BD-video with region “A” and DVD-video  
with region “1” or “ALL”. You cannot play  
back BD-video or DVD-video that are  
labeled for other regions. Look for the  
symbols on the right on your BD-video or  
DVD-video.  
If these region symbols do not appear on  
your BD-video or DVD-video, you cannot  
play back the disc in this unit. The letter or  
number inside the globe refers to region  
of the world. A BD-video or DVD-video  
labeled for a specific region can only be  
played back in the unit with the same  
region code.  
DVD-video  
off A Chapter information (elapsed time)  
A Chapter information (remaining time)  
A Title information (elapsed time)  
A Title information (remaining time)  
A Audio format information A off  
Track information (elapsed time)  
A Track information (remaining time)  
A Disc information* (elapsed time)  
A Disc information* (remaining time)  
A Track information (elapsed time)  
(* not available during program / random playback)  
Structure of Disc / SD Memory Card Contents  
The contents of BD / DVD are generally divided into titles.  
Titles may be further subdivided into chapters.  
BD / DVD  
title 1  
chapter 1  
title 2  
chapter 2 chapter 1 chapter 2 chapter 3  
off A File information A File name information A off  
audio CD are divided into tracks.  
audio CD  
track 1  
track 2  
track 3  
track 4  
track 5  
Data discs or SD Memory Cards containing JPEG are  
divided into folders, and the folders are subdivided into  
files.  
JPEG  
folder (group) 2  
file 4  
folder (group) 1  
file 1  
file 2  
file 3  
file 5  
EN  
15  
PLAYBACK  
S Chapter information  
S Track / File information  
<Title / Chapter information for BD>  
1
2
3
4
1
2
3
4
5
1 / 14  
0 : 00: 51  
SD  
G
1
1/10  
T
1
2
Current track (file) number / Total number of track  
(file)  
Elapsed time / Remaining time of the current track  
(except for JPEG files)  
<Chapter information for DVD>  
2
6
3
4
Indication of SD Memory Card playback  
Current repeat setting  
3 / 5  
0 : 01 : 02  
(Only when repeat setting is active)  
(T: Track repeat, G: Group repeat,  
A: All repeat)  
1
2
3
Current title number  
Current chapter number / Total number of chapters  
Current repeat setting (Only when repeat setting is  
active)  
(C: Chapter repeat, T: Title repeat)  
Indicates that the multi camera angle images are  
available on the scene  
Current playback status  
S Disc information  
1
2
4
1 / 14  
0 : 00: 51  
T
5
6
1
2
Current track number / Total number of tracks  
Elapsed time / Remaining time of the current disc  
Elapsed time / Remaining time of the current chapter  
S Title information  
S File name information  
1
2
1
3 / 5  
0 : 01 : 02  
File_name_001  
1
2
Current title number / Total number of titles  
Elapsed time / Remaining time of the current title  
1
Media icon and file name  
: JPEG file  
S Audio format information  
1
Dolby Digital  
1
Audio format  
16  
EN  
PLAYBACK  
Use [K / L] to select “SD Card”,  
How to Insert a Disc  
then press [OK].  
2
Press [OPEN/CLOSE A] to open the  
disc tray.  
1
2
Media Select  
Disc  
SD Card  
Place the disc on the disc tray with its  
label side facing up.  
Align the disc to the  
disc tray guide.  
Use [K / L] to select a desired track,  
folder or file, then press [OK].  
3
Use [s / B] to go back and forward  
between the hierarchies.  
• If you press [OK] on the desired file,  
playback will start.  
• Make sure the disc is compatible with this unit.  
(Refer to page 14 for the list of compatible discs.)  
Press [OPEN/CLOSE A] to close the  
To remove the SD Memory Card:  
In stop mode, gently push in the SD Memory  
Card, then pull it out slowly.  
disc tray.  
3
It may take a while to load the disc.  
Note  
• The “Media Select” screen will disappear under the  
To eject the disc:  
conditions listed below:  
Press [OPEN/CLOSE A] to open the disc tray.  
Remove the disc.  
- when the screen saver is activated.  
- when [RETURN] is pressed.  
- when the setup menu is called up.  
Press [OPEN/CLOSE A] to close the disc tray.  
• If the “Media Select” screen disappears before you  
make the selection, refer to “Selecting the Media  
Mode” on page 18.  
Reading the SD Memory Card  
• Do not remove the SD Memory Card or turn the unit  
to the standby mode while the contents of the card  
are in playback. It may result in malfunction or loss of  
the card’s data.  
• Do not delete the folders or files in the SD Memory  
Card with your computer. This unit may not read the  
SD Memory Cards formatted on a computer.  
You can play back the JPEG files in an SD Memory Card.  
With the SD Memory Card, you can also enjoy the special  
additional contents for BD-ROM Profile 1 ver.1.1 which can  
be downloaded from the Internet. You can store the  
contents on an SD Memory Card via computer and play  
them back with the BD-video. For more information about  
the special additional contents, please refer to the  
instruction book that came with the disc.  
Insert an SD Memory Card, with the  
label side facing up, into the SD  
1
card slot until it clicks.  
If no disc is in operation, “Media Select” screen  
will appear on the TV screen.  
OPEN/  
CLOSE  
DISC IN  
STANDBY-ON  
SD card  
STANDBY-ON  
SD rd  
SD Memory Card  
EN  
17  
PLAYBACK  
Selecting the Media Mode  
For the playback media to be read by this unit, the correct media mode should be selected. You can switch the media  
mode by following the steps below. “Media Select” is available only when an SD Memory Card is inserted.  
is  
e
hen  
SD  
y
In stop mode, press [SETUP].  
is  
1
2
Use [K / L] to select , then press  
[OK] .  
Quick  
Media Select  
Disc  
HDMI Audio Out  
HDMI Multi(Normal)  
HDMI Video Resolution Auto  
Component Output  
Player Menu  
480i  
English  
Use [K  
/
L
] to select “Media Select”.  
3
Quick  
Media Select  
Disc  
HDMI Audio Out  
HDMI Multi(Normal)  
HDMI Video Resolution Auto  
Component Output  
Player Menu  
480i  
English  
Press [OK] repeatedly to select the  
desired media.  
4
5
Press [SETUP] to exit.  
• Selected media mode is now activated.  
Even if you turn the unit to the standby mode in “SD Card”  
mode, it will be in “Disc” mode the next time you turn it on.  
18  
EN  
PLAYBACK  
Playing Back (BD / DVD)  
Press [STANDBY-ON Q].  
1
2
3
4
Turn on the TV and select the  
appropriate input on the TV to  
which the unit is connected.  
Insert a disc (refer to page 17 on how  
to insert a disc).  
Playback may start automatically.  
If not, press [B (play)].  
Some discs may show a title or a disc menu.  
In such case, refer to “Using the Title / Disc /  
Pop-up Menu” on page 20.  
To pause playback:  
Press [F (pause)].  
To return to the normal playback:  
Press [B (play)].  
To stop playback:  
Press [C (stop)].  
Playback will be in Resume-On-Stop mode.  
Resume-On-Stop mode  
If a playback is in Resume-On-Stop mode, when you press  
[B (play)] next time, the playback will start from the point  
where it has been stopped.  
Note  
• Resume playback may not be available for the BD that  
supports Java applications (BD-Java).  
• In the “Disc” mode, the resume information will be  
cleared when;  
- [C (stop)] is pressed while in the Resume-On-Stop  
mode.  
- the parental level is changed.  
- the disc tray is opened.  
• In the “SD Card” mode, the resume information will be  
cleared when;  
- [C (stop)] is pressed while in the Resume-On-Stop  
mode.  
- the SD Memory Card is removed.  
- the unit is turned into the standby mode.  
Note  
may appear at the top-right on the TV screen  
when the operation is prohibited by the disc or this  
unit.  
• During the playback of 2-layered disc, pictures may  
stop for a moment. This happens when the 1st layer  
switches to the 2nd layer. This is not a malfunction.  
• The operation may vary when you play back BD-  
video and DVD-video with disc menu. Refer to the  
manual accompanying the disc for details.  
• Set “Still Mode” setting to “Field” in “Video” menu if  
pictures in the pause mode are blurred. Refer to “Still  
Mode” on page 33.  
EN  
19  
PLAYBACK  
Playing Back (Audio CD / JPEG Files)  
Using the Title / Disc / Pop-up Menu  
Before you begin, make sure the correct media mode is  
Many of BD-video and DVD-video discs contain title menu  
(BD-video / DVD-video), disc menu (DVD-video) or pop-up  
menu (BD-video) which guides you through the available  
functions in the disc. The contents of the menus may differ  
depending on the discs.  
selected. Refer to “Selecting the Media Mode” on page 18.  
Insert an audio CD or a disc/card  
with JPEG files.  
1
2
Title menu (BD-video / DVD-video)  
1 Press [TOP MENU].  
Use [K / L] to select a desired track,  
folder or file, then press [OK].  
2 Use [K / L / s / B] to select an item, then press  
Use [s / B] to go back and forward  
[OK].  
between the hierarchies (only for  
3 Press [TOP MENU] to exit.  
JPEG files).  
• If you press [OK] on the desired file, playback  
Disc menu (DVD-video)  
will start.  
1 Press [POP MENU / MENU].  
1
2
3
5
6
4
2 Use [K / L / s / B] to select an item, then press  
[OK].  
- - / 20  
3 Press [POP MENU / MENU] to exit.  
File List  
JPEG_DISC  
Folder_1  
Folder_2  
Folder_3  
JPEG_A  
JPEG_B  
JPEG_C  
JPEG_D  
Pop-up menu (BD-video)  
• This is a special feature available for some BD-videos.  
When you press [POP MENU / MENU], a menu pops  
out on the TV screen during play back.  
1 During the playback of BD-video, press  
[POP MENU / MENU].  
Page Up  
Page Down  
2 Use [K / L / s / B] to select an item, then press  
[OK].  
e.g.) JPEG  
3 Press [POP MENU / MENU] to exit.  
1
2
audio CD : Track information  
JPEG : File information  
audio CD : “CD-DA” will be displayed.  
Note  
• Contents of menus and corresponding menu  
operations may vary among discs. Refer to the  
manual accompanying the disc for details.  
JPEG  
: Current Disc, SD Memory Card, or  
folder name will be displayed.  
3
4
audio CD : List of the track number and time.  
JPEG : List of the file / folder names in the  
current folder / disc  
Operation: Press [RED] to go to the previous page.  
guide Press [GREEN] to go to the next page.  
5
6
Current page / Total page number  
Playback status  
Icons:  
: Folder  
: audio CD tracks  
: JPEG files  
Press [C (stop)] to stop playback.  
3
20  
EN  
PLAYBACK  
It is recommended that files to be played back in this  
1
2
3
File information  
Current page / Total page number  
Operation guide: Press [BLUE] to go to the previous  
unit are recorded under the following specifications:  
<JPEG>  
• Upper limit  
: 2,560 x 1,900 dots (sub sampling is  
4:4:4)  
page.  
5,120 x 3,840 dots (sub sampling is  
Press [YELLOW] to go to the next  
page.  
up to 4:2:2)  
4
• Lower limit  
: 32 x 32 dots  
Playback status  
• File size of image : 12 MB  
maximum  
Use [K / L / s / B] to select a  
desired file to be played back, then  
2
Note  
press [B (play)] or [OK].  
• Do not delete the folders or files in the SD Memory  
Card with your computer. This unit may not read the  
SD Memory Cards formatted on a computer.  
• With regard to the multi-border BD-RE/-R,  
additionally recorded sections cannot be  
recognized.  
• An image will be played back from the  
selected file and go to the next one in turn.  
Press [C (stop)] to stop playback.  
To return to the first item:  
Press [TOP MENU].  
3
• With regard to the multi-border DVD-RW/-R,  
additionally recorded sections may not be  
recognized.  
To return to the file played last:  
Press [POP MENU / MENU].  
Tips for JPEG / Kodak Picture CD Playback  
Kodak Picture CD  
• Every press on [ANGLE] will turn the image  
clockwise by 90 degrees when an image is displayed.  
• To change the visual effect for switching the  
playback image, press [MODE] once, then use  
[s / B] or [OK] to switch between “Cut In/Out” and  
“Fade In/Out”.  
This unit can also run JPEG files stored on Kodak Picture  
CD. You can enjoy picture images on the TV set by playing  
back the Kodak Picture CD. This unit conforms to ver.7.0 of  
Kodak Picture CD. For details of Kodak Picture CD, contact  
a shop that provides developing service of Kodak Inc.  
• During JPEG / Kodak Picture CD playback, press  
[MODE] twice to change the size of the playback  
image, then use [s / B] or [OK] to switch between  
“Normal” (100 %) and “Small” (95 %). The size change  
may have no effect on some files (e.g. files with a  
small picture size).  
When Kodak Picture CD is inserted  
in this unit, Kodak Picture CD menu  
1
will appear automatically on the TV  
screen.  
Note  
1
4
• Unrecognizable characters will be replaced with  
asterisks.  
- - / 16  
• Some unplayable folders or files may be listed due to  
the recording status.  
Thumbnail  
Pictures  
• High-resolution JPEG files take longer to be  
displayed.  
• Progressive JPEG files (JPEG files saved in progressive  
format) cannot be played back in this unit.  
• The system can recognize up to 255 folders / 999 files  
for CD, 999 folders / 9,999 files for DVD and SD  
Memory Card.  
• The 9th and deeper hierarchies cannot be displayed  
for CD. The 10th and deeper hierarchies cannot be  
displayed for DVD and SD Memory Card.  
• For the SD Memory Card playback, refer to “Reading  
the SD Memory Card” on page 17.  
㪉㩷 㩷 㪆㩷 㩷 㪊  
Page Prev  
Page Next  
2
3
• For an SD Memory Card, only an extension of .jpg”  
can be recognized. For other media, only .jpg” and  
.jpeg” can be recognized, and any other extensions  
cannot be read.  
EN  
21  
PLAYBACK  
Fast Forward / Fast Reverse  
Step by Step Playback  
1 During playback, press [D (forward)]  
1 In pause mode, press [F (pause)] repeatedly.  
repeatedly for fast forward.  
Every time you press [F (pause)], playback will  
During playback, press [E (reverse)] repeatedly  
for fast reverse.  
Every time you press [D (forward)] or  
[E (reverse)], the playback speed will change.  
advance one step at a time.  
2 Press [B (play)] to return to normal playback.  
Note  
2 Press [B (play)] to return to normal playback.  
• Only step by step forward is available.  
• Set “Still Mode” setting to “Field” in “Video” menu if  
pictures in step by step playback mode are blurred.  
Refer to “Still Mode” on page 33.  
Note  
• For BD, the approximate speed for the fast forward is  
1 (1.3x), 2 (10x), 3 (30x), 4 (70x), and 5 (200x). And for  
the fast reverse, it is 1 (2x), 2 (10x), 3 (30x), 4 (70x),  
and 5 (200x).  
Repeat Playback  
Available repeat functions vary depending the discs.  
1 During playback, press [REPEAT] repeatedly to  
select the desired repeat mode.  
• For DVD, the approximate speed for the fast forward  
or reverse playback is 1 (2x), 2 (8x), 3 (20x),  
4 (50x), and 5 (100x).  
• For audio CD, the approximate speed is 1 (2x), 2 (8x),  
and 3 (30x).  
• For audio CD, fast forward / fast reverse search  
between different tracks are not available during  
program and random playback.  
Repeat mode  
Chapter repeat  
Available media  
The current chapter will be played  
back repeatedly.  
Title repeat  
Slow Forward Playback  
The current title will be played back  
repeatedly.  
Track repeat  
The current track will be played back  
repeatedly.  
Group repeat  
The current folder will be played  
back repeatedly.  
1 During playback, press [F (pause)], then press  
[D (forward)].  
Every time you press [D (forward)], playback  
speed will change.  
2 Press [B (play)] to return to normal playback.  
All repeat  
All tracks or files in the media will be  
played back repeatedly.  
Note  
• The approximate speed for the slow forward  
playback is 1 (1/16x), 2 (1/8x), 3 (1/2x).  
• Only slow forward is available.  
Note  
• Set “Still Mode” setting to “Field” in “Video” menu if  
pictures in the slow forward playback mode are  
blurred. Refer to “Still Mode” on page 33.  
• The repeat setting will be canceled when you stop  
playback.  
• The chapter, title, track or group repeat will be  
cleared when moving to another chapter, title, track /  
file or folder.  
• Chapter and title repeat are not available with some  
scenes.  
22  
EN  
PLAYBACK  
3 Press [B (play)] to start program playback.  
Program Playback  
• The program playback will start.  
efore  
ou  
begin  
2 / 16  
Program  
CD_DA  
0 : 01 : 05  
You can play back the disc/card in your desired order.  
Total  
0 : 26 : 24  
1 In stop mode, press [MODE].  
2
4
1:14  
2 Use [K / L] to select a track / file, then press  
0:50  
1:14  
0:50  
0:53  
0:54  
0:36  
[OK].  
9
11  
12  
14  
8
1
2
3
4
5
6
- - / 16  
ꢀꢁꢁꢂꢁꢁꢃ  
Program  
CD_DA  
Total  
0 : 26 : 24  
Page Down  
8
9
0:36  
2
4
9
1:14  
To exit from the program playback mode:  
1:14  
0:45  
0:50  
0:53  
0:20  
0:54  
0:50  
1:14  
0:50  
0:53  
0:54  
0:36  
10  
11  
12  
13  
14  
• Press [RETURN] in stop mode.  
11  
12  
14  
8
Note  
• During program playback, press [C (stop)] once to  
set the resume point, and then press [B (play)] to  
resume program playback from where [C (stop)]  
was pressed (audio CD) or from beginning of the file  
where [C (stop)] was pressed (JPEG).  
ꢀꢁꢁꢂꢁꢁꢃ  
ꢀꢁꢁꢂꢁꢁꢃ  
7
8
Page Up  
Page Down  
Page Prev  
Page Next  
e.g.) audio CD  
• During program playback, press [C (stop)] twice to  
display the program screen. To go back to the normal  
program playback, press [RETURN] to exit from the  
program screen, then press [B (play)].  
1
2
audio CD  
JPEG  
audio CD  
JPEG  
: Track information  
: File information  
: “CD-DA” will be displayed.  
: Current Disc, SD Memory Card,  
or folder name will be displayed.  
• Up to 99 tracks / files can be entered.  
• To repeat the current track / file in the program,  
3
4
5
press [REPEAT] repeatedly until “  
Track”  
Track / File list : Track / File list in the original  
order.  
Programmed list : Track / File list in the  
programmed order.  
Cumulative playback time of all tracks / files in the  
programmed list.  
Playback status  
appears during playback. To repeat the entire  
program, press [REPEAT] repeatedly until “  
All”  
appears during playback.  
• Playback from a desired track / file and random  
playback are not available during program playback.  
• Press [MODE] to switch to the random playback mode.  
• The program will be cleared when;  
6
7
- the unit is turned into the standby mode.  
Current page / Total page number  
- the media mode is switched to the other mode.  
- the disc / card is removed. (as for “Disc” mode, just  
opening the disc tray will clear the program info.)  
8
Operation Guide: Press [RED] to go to the previous  
page in the track / file list.  
Press [GREEN] to go to the next  
page in the track / file list.  
Press [BLUE] to go to the  
previous page in the  
programmed list.  
Press [YELLOW] to go to the next  
page in the programmed list.  
• For JPEG files, use [K / L] to select a folder, then press  
[OK] first, and then use [K / L] to select a file, then  
press [OK].  
• Press [CLEAR] to erase the last file of the program.  
• Use [K / L] to select “All Clear” at the bottom of the  
list to erase all the tracks / files in the program.  
• The programmed tracks / files is displayed in the right  
hand screen.  
• Use [s / B] to go back / forward between the  
hierarchy of folders.  
EN  
23  
PLAYBACK  
Random Playback  
Rapid Playback  
This function shuffles the playback order of tracks / files.  
1 In stop mode, press [MODE] twice.  
This function plays back approximately at 1.3 times the  
normal playback while keeping the sound output. This  
function is available only on discs recorded in the Dolby  
Digital format.  
1
2
3
4
5
6
- - / 16  
1 During playback, press [MODE] repeatedly  
Random  
CD_DA  
Total  
1 : 13 : 29  
until the Rapid playback setting appears.  
Off  
1
2
3
4
5
6
7
0:36  
1:14  
0:45  
0:50  
0:53  
0:20  
0:54  
2 Press [OK] or [s / B] to switch  
“Off” : Plays back in normal speed.  
(1.3x), or off.  
: Plays back approximately at 1.3 times of normal  
playback.  
ꢀꢁꢁꢂꢁꢁꢃ  
Page Down  
3 Press [B] to return to normal playback.  
e.g.) audio CD  
1
2
audio CD  
: Track information  
: File information  
: “CD-DA” will be displayed.  
: Current Disc, SD Memory Card, or  
folder name will be displayed.  
Note  
JPEG  
• Picture adjustment and audio language setting  
cannot be changed during this function.  
audio CD  
JPEG  
• Virtual surround does not work during this function.  
• This function may not work at some points on a disc.  
• During this function, 2ch LPCM will be output from  
HDMI OUT jack and DIGITAL OUT jack.  
3
4
Track / File list : Track / File list in the original order  
will be displayed.  
Operation  
Guide  
: Press [RED] to go to the previous  
page in the track / file list.  
Press [GREEN] to go to the next  
page in the track / file list.  
Adjusting the Picture  
5
6
You can adjust the picture quality.  
Total playback time of all tracks / files.  
Playback status  
1 During playback, press [MODE] repeatedly  
until  
appears.  
2 Press [B (play)] to start random playback.  
To exit from the random playback mode:  
• Press [MODE] in stop mode.  
2 Use [K / L] to select your desired item, then  
use [s / B] to adjust the setting.  
Black Level  
On  
Off  
Note  
Noise Reduction  
• During the random playback, press [C (stop)] once  
to set the resume point, and then press [B (play)] to  
resume random playback from where [C (stop)] was  
pressed (audio CD) or from beginning of the file  
where [C (stop)] was pressed (JPEG).  
e.g.) DVD-video  
S Black level  
You can adjust the black level setting to make the black  
parts of the pictures as bright as you prefer. You can select  
“On” or “Off”.  
• To repeat the current track / file in the random  
selection, press [REPEAT] repeatedly until  
Track” appears during playback. To repeat the  
entire random selection press [REPEAT] repeatedly  
until “ All” appears during playback.  
“On” :Makes the dark parts brighter.  
“Off:Shows the original picture as recorded.  
• Playback from a desired track / file is not available  
during random playback.  
• Press [RETURN] to switch to the program playback  
mode.  
24  
EN  
PLAYBACK  
S Noise reduction (DVD-video only)  
PIP (BONUSVIEW) Setting  
Reduces the noise of the playback picture.  
“Off” :Shows the original picture as recorded.  
“1” :Executes 3D noise reduction which detects and  
deletes the noise by comparing each picture  
frames.  
“2” :Executes MPEG noise reduction which reduces  
the block noise and mosquito noise on the  
subtitle on movie.  
Some BD-video have the PIP function which enables you  
to display the secondary video in the primary video. You  
can call up the secondary video by pressing [MODE]  
whenever the scene contains the secondary video.  
“3” :Executes both MPEG noise reduction and 3D  
noise reduction.  
3 Press [RETURN] to exit.  
primary  
video  
Note  
• The setting will remain the same even if the unit is  
turned to the standby mode.  
secondary  
video  
• For the picture output from HDMI OUT jack, “Black  
Level” is not effective.  
• You cannot adjust the setting during rapid playback.  
1 During playback, press [MODE] repeatedly  
until the PIP function appears.  
2 Use [K / L] to select the secondary video you  
Virtual Surround  
want.  
• The secondary video will be displayed and the  
secondary audio will be output.  
You can enjoy stereophonic virtual space through your  
existing 2 channel stereo system.  
3 Press [RETURN] or [MODE] to remove the PIP  
information.  
1 During playback, press [MODE].  
2 Use [K / L] to select your desired setting.  
Note  
• The secondary audio will not be output when the  
secondary audio is set to “Off” or when “BD Audio  
Mode” is set to “HD Audio Output”. Refer to  
“Switching Audio Soundtrack” on page 27 and  
“Setting the BD Audio Mode” on page 28.  
Off  
“Off” :No surround effect  
“1” :Natural surround effect  
“2” :Stronger surround effect  
3 Press [RETURN] to exit.  
Camera Angle  
Note  
• Set the virtual surround setting to “Off” or lower the  
volume if the sound is distorted.  
• Virtual surround does not function during rapid  
playback.  
Some BD-video and DVD-video contain scenes which have  
been shot simultaneously from various angles. You can  
change the camera angle when  
screen.  
• For the virtual surround, audio signal will always be  
2-channel LPCM.  
appears on the TV  
1 During playback, press [ANGLE].  
• The selected angle will be displayed on the display  
bar at the top of the TV screen.  
2 Use [K / L] to select your desired angle.  
1 / 3  
Note  
• If “Angle Icon” setting is “Off” in “Others” menu,  
will not appear. Refer to page 40.  
EN  
25  
PLAYBACK  
Using [Number buttons] (Direct Search)  
Search  
Title Search  
Using [H / G (skip)]  
1) In stop mode, enter the title number you want to  
search using [Number buttons].  
1 During playback, press [G (skip)] to move to  
Playback of the title will start in a few seconds.  
the next track / title / chapter / file. Press it  
repeatedly to skip to subsequent tracks. Press  
[H (skip)] once to go back to the beginning of  
the current track. Press it repeatedly to go to  
the previous tracks.  
Chapter Search  
1) During playback of a title, enter the chapter number  
you want to search using [Number buttons].  
Playback of the chapter will start in a few seconds.  
• For JPEG files, press [H (skip)] to go back to the  
previous file.  
Note  
• As for the BD-video, how it performs will be strongly  
determined by the disc, and may not perform as  
described here.  
Note  
• For BD and DVD, if title contains no chapters,  
[H / G (skip)] changes the title.  
• For JPEG files, [s / B] is also available.  
Using [SEARCH]  
By using [SEARCH], you can select the following search  
modes.  
Search mode  
Available media  
/
Chapter / Title search  
Track search  
Time search  
1 During playback, press [SEARCH] repeatedly  
until your desired search mode appears.  
2 Enter the desired chapter, title, track, file  
number or time to search for using  
[Number buttons].  
• Chapter, title, track or time search will start.  
• Press [CLEAR] to erase an incorrect input.  
Note  
• During program and random playback, search  
functions are not available except the search using  
[H / G (skip)].  
• Time search is available only in the same track, file or  
title.  
• For BD, chapter and time search are available only  
during playback.  
26  
EN  
PLAYBACK  
You can select the format of audio and video as you prefer depending on the contents of the disc you are playing back.  
Switching Subtitles  
Switching Audio Soundtrack  
Some BD and DVD may have subtitles in 1 or more  
languages. For commercially available discs, the  
supported languages can be found on the disc case.  
Follow the steps below to switch the subtitle languages  
during playback.  
Some BD and DVD contain multiple audio streams. Those  
are often in different audio languages or audio formats.  
For BD, available audio varies depending on “BD Audio  
Mode” setting. Refer to page 34 for more information.  
1 During playback, press [SUBTITLE].  
2 Use [K / L] to select “Primary Subtitle”,  
“Secondary Subtitle” or “Subtitle Style”, then  
press [OK].  
1 During playback, press [AUDIO].  
2 Use [K / L] to select “Primary” or “Secondary”  
audio to set, then press [OK].  
Primary  
1
ENG  
Secondary  
ENG  
Dolby D  
Multi-ch  
Multi-ch  
/3  
/3  
Primary Subtitle  
Secondary Subtitle  
Subtitle Style  
2 ENG/11  
2 ENG/11  
2/25  
2
Dolby D+  
“Primary”  
: Sets the audio for the primary video.  
“Primary Subtitle”  
: Sets the subtitle for the  
primary video.  
“Secondary” : Sets the audio for the secondary video.  
3 Use [K / L] to select your desired audio stream  
“Secondary Subtitle” : Sets the subtitle for the  
secondary video.  
channel.  
“Subtitle Style”  
: Sets style of the subtitle.  
• For “Secondary”, use [s / B] to switch between  
current audio setting and “Off”.  
4 Press [AUDIO] to exit.  
3 Use [K / L] to select your desired subtitle or  
style.  
• Use [s / B] to switch between current subtitle  
setting and “Off”.  
4 Press [SUBTITLE] to exit.  
1 During playback, press [AUDIO].  
2 Use [K / L] to select your desired audio stream  
channel.  
1 During playback, press [SUBTITLE].  
2 Use [K / L] to select your desired subtitle.  
1
ENG  
Dolby D 3/2.1ch  
48k  
/ 3  
e.g.) DVD-video  
• For audio CD, you can select following options.  
1
/ 4  
ENG  
“Stereo” : Both right and left channels are active  
• Use [s / B] to switch between current subtitle  
(stereo).  
setting and “Off”.  
“L-ch” : Only left channel is active.  
“R-ch” : Only right channel is active.  
3 Press [AUDIO] to exit.  
3 Press [SUBTITLE] to exit.  
Note  
• Some discs will only allow you to change the  
subtitles from the disc menu or pop-up menu. Press  
[TOP MENU] or [POP MENU / MENU] to display the  
disc menu or pop-up menu.  
• If 4-digit-language code appears in the subtitle  
menu, refer to “Language Code List” on page 47.  
• If the disc has no subtitle language or subtitle style,  
“Not Available” will be displayed on the TV screen.  
• During playback of the secondary video, the primary  
subtitle setting is not available except when there is  
no subtitle for the secondary video.  
• If you select a language that has a 3-letter-language  
code, the code will be displayed every time you  
change the subtitle language setting. If you select  
any other languages, “---” will be displayed instead.  
(Refer to page 47.)  
EN  
27  
PLAYBACK  
Setting the BD Audio Mode  
Note  
• The secondary audio will not be output when the  
secondary video is not displayed or when “BD Audio  
Mode” is set to “HD Audio Output”. (For some BD,  
secondary audio will be output even when  
secondary video is off.)  
There are 2 options for the “BD Audio Mode” setting; either  
by setting the output to the secondary and interactive  
audio accompanied by the primary audio or by setting  
only the primary audio. Depending on the setting of the  
mode, Dolby Digital, Dolby Digital Plus, Dolby TrueHD,  
DTS, or DTS-HD output changes between multi LPCM and  
bitstream.  
• The sound mode cannot be changed during  
playback of discs not recorded in multiple audio.  
• Some discs allow changing the audio language  
setting on the disc menu. (Operation varies  
depending on the discs. Refer to the manual  
accompanying the disc.)  
[AUDIO] may not work on some discs with multiple  
audio streams or channels (e.g. DVDs that allow  
changing audio setting on the disc menu).  
• If you select a language that has a 3-letter-language  
code, the code will be displayed every time you  
change the audio language setting. If you select any  
other languages, “---” will be displayed instead.  
(Refer to page 47.)  
1 In stop mode with BD inserted, press [MODE].  
2 Use [K / L] to select your desired setting.  
BD Audio Mode  
Mix Audio Output  
“Mix Audio Output”:  
If it is available, BD-video’s secondary and interactive  
audio will be output with the primary audio.  
• The secondary audio is the audio for the secondary  
video (Director’s comment etc.) and the interactive  
audio is the audio for the interactive application  
(Button click sounds etc.).  
• Audio Language selection cannot be made during  
rapid playback. (Refer to page 24.)  
• If 4-digit-language code appears in the audio menu,  
refer to page 47.  
• If the disc has no audio language, “Not Available” will  
be displayed on the TV screen.  
• For DTS-CD (5.1 music disc), selecting audio streams  
or channels is not available.  
“HD Audio Output”:  
Only the primary audio will be output. Set this mode in  
order to output , Dolby Digital Plus, Dolby TrueHD, or  
DTS-HD audio of BD through HDMI connection.  
3 Press [RETURN] to exit.  
• You can also set “BD Audio Mode” from the setup  
menu. Refer to page 34.  
• Refer to “Audio signals output from HDMI OUT jack”  
on page 35 and “Audio signals output from DIGITAL  
OUT (COAXIAL) jack” on page 36 for how BD Audio  
will be output.  
Note  
• In “Mix Audio Output” mode, if there is no secondary  
and interactive audio, the audio will be output as  
“HD Audio Output” mode.  
28  
EN  
FUNCTION SETUP  
Using the Setup Menu  
In the setup menu you can change the setting for audio,  
video, language, etc. You cannot change the setting  
during playback.  
Setting items displayed in gray indicates they are not  
available under the conditions at the time.  
Quick  
Quick” menu contains setting items extracted from  
Custom” menu which may be used frequently.  
In stop mode, press [SETUP].  
1
2
3
Use [K / L] to select , then press  
[OK].  
Use [K / L] to select your desired  
setting items.  
Quick  
Media Select  
Disc  
HDMI Multi(Normal)  
Auto  
HDMI Audio Out  
HDMI Video Resolution  
Component Output  
Player Menu  
480i  
English  
Follow the procedure below  
depending on the setting items.  
4
5
A) If B” does not appear on the right side  
of the setting items when you select the  
items:  
Press [OK] repeatedly to change  
options.  
B) If B” appears on the right side of the  
setting items when you select the items:  
1) Press [OK].  
2) Use [K / L] to select options, then  
press [OK].  
• Use [s] or [RETURN] to go back to the  
previous screen.  
Press [SETUP] to exit.  
EN  
29  
FUNCTION SETUP  
Custom  
Custom” menu contains all the setting items.  
In stop mode, press [SETUP].  
1
2
3
Use [K / L] to select  
[OK].  
, then press  
Use [K / L] to select your desired  
setting category, then press [OK].  
: Language  
: Video  
: Audio  
: Parental  
: Others  
• For “Parental” menu, follow the procedure  
on page 39.  
Use [K / L] to select your desired  
setting items.  
4
5
Follow the procedure below  
depending on the setting items.  
A) If B” does not appear on the right side  
of the setting items when you select the  
items:  
Press [OK] repeatedly to change  
options.  
B) If B” appears on the right side of the  
setting items when you select the items:  
1) Press [OK].  
2) Use [K / L] to select options, then  
press [OK].  
• Use [s] or [RETURN] to go back to  
the previous screen.  
Press [SETUP] to exit.  
6
30  
EN  
FUNCTION SETUP  
S
Language  
Language  
Audio  
Original  
Off  
Subtitle  
Disc Menu  
Player Menu  
English  
English  
• To select the setting items and options, refer to “ Custom” on page 30.  
• “ Quick” menu consists of the setting menus frequently used, and they are accompanied with  
.
Setting items  
Options  
Audio  
Original* / English / French / Spanish / German / Italian / Swedish / Dutch /  
Russian / Chinese / Japanese / Korean / Danish / Finnish / Norwegian / Icelandic /  
Hungarian / Romanian / Turkish / Greek / Irish / Portuguese / Polish / Czech /  
Slovak / Bulgarian / Other  
Sets the language for audio.  
Subtitle  
Sets the language for subtitle.  
Off* / English / French / Spanish / German / Italian / Swedish / Dutch / Russian /  
Chinese / Japanese / Korean / Danish / Finnish / Norwegian / Icelandic /  
Hungarian / Romanian / Turkish / Greek / Irish / Portuguese / Polish / Czech /  
Slovak / Bulgarian / Other  
Disc Menu  
English* / French / Spanish / German / Italian / Swedish / Dutch / Russian /  
Sets the language for disc menu or Chinese / Japanese / Korean / Danish / Finnish / Norwegian / Icelandic /  
pop-up menu.  
Hungarian / Romanian / Turkish / Greek / Irish / Portuguese / Polish / Czech /  
Slovak / Bulgarian / Other  
*1  
Player Menu  
Sets the language for OSD  
(on-screen display).  
Auto(XXXX) / English* / Français / Español  
*)Settings with (*) are the default.  
*1) “Auto” activates the Get & Set Menu Language function. Refer to page 41.  
- “Auto” is available only when “HDMI CEC” is set to “On”.  
- inside the parentheses next to “Auto” will be the language which is currently selected by your TV.  
• For “Audio”, “Subtitle”, and “Disc Menu”, if you select “Other”, enter the 4-digit-number code for the desired language.  
(Refer to “Language Code List” on page 47.) Only the languages supported by the disc can be selected.  
EN  
31  
FUNCTION SETUP  
S
Video  
Video  
TV Aspect  
16:9 Wide  
Auto  
HDMI Video Resolution  
HDMI Deep Color  
Auto  
Component Output  
Progressive Mode  
480i  
Auto  
Still Mode  
Auto  
• To select the setting items and options, refer to “ Custom” on page 30.  
• “ Quick” menu consists of the setting menus frequently used, and they are accompanied with  
.
Setting items  
Options  
TV Aspect  
Sets the picture size according to  
aspect ratio of the connected TV.  
16:9 Wide*:  
Select this when a wide-screen TV is connected. Discs recorded in wide-screen  
format is played back over the entire TV screen.  
4:3 Pan & Scan:  
Select this to play back the discs recorded in wide-screen format with 4:3 TV in  
the pan & scan mode (with the sides of the picture cut off). Discs which are not  
specified for pan & scan are played back in the letter box mode.  
4:3 Letter Box:  
Select this to play back the discs recorded in wide-screen format with 4:3 TV in  
the letter box mode. (with black strips at the top and bottom.)  
16:9 Squeeze:  
When playing back 4:3 images, the picture is displayed in the center of the 16:9  
screen with a 4:3 aspect ratio.  
HDMI Video Resolution  
Sets the HDMI video resolution.  
Auto*:  
HDMI video resolution will be selected automatically depending on the  
connected HDMI device.  
480p  
HDMI Deep Color  
Auto*:  
Sets whether to output the picture  
The picture from HDMI OUT jack will be output with Deep Color to the  
from HDMI OUT jack with Deep Color connected TV which supports HDMI Deep Color.  
or not.  
Off:  
The picture from HDMI OUT jack will be output without Deep Color.  
Component Output  
Sets the video resolution for  
component output.  
480i*  
480p  
720p  
1080i  
Auto*:  
Progressive Mode  
Sets the optimum progressive mode The progressive mode will detect 24-frame film material (movies) and  
for the image material output from  
HDMI OUT jack and COMPONENT  
VIDEO OUT jacks.  
automatically select appropriate progressive mode.  
Video:  
Suited for playing back video material discs (TV shows or animation).  
32  
EN  
FUNCTION SETUP  
Setting items  
Options  
*1  
Auto*:  
Still Mode  
Automatically selects the best resolution setting (“Frame” or “Field”) based on  
the data characteristics of the pictures.  
Adjusts picture resolution and quality  
in still mode.  
Field:  
Stabilizes the pictures, although the picture quality may become coarse due to  
the limited amount of data. Select “Field” when the pictures are still unstable  
even if “Auto” is selected.  
Frame:  
Displays relatively motionless pictures in higher resolution. “Frame” improves  
the picture quality, although it may unstabilize the pictures due to alternate  
output of 2-field data.  
*)Settings with (*) are the default.  
*1) An individual picture on the TV screen is called “Frame”, which consists of two separate images called “Field”.  
Some pictures may be blurred at the auto setting in “Still Mode” setting due to their data characteristics.  
Note for “HDMI Video Resolution” and “Component Output”  
• Even if you set “HDMI Video Resolution” setting to “Auto”, when this unit is connected to a DVI compatible display  
devices with an HDMI-DVI cable, 480p signal will be output.  
• Video and audio signals may be distorted temporarily when switching to / from the HDMI output mode.  
• You cannot change the video resolution during Blu-ray Disc playback. To change the resolution, stop playback.  
• In order to get natural and high quality film reproduction of 24-frame film material, use an HDMI cable (High Speed  
HDMI Cable is recommended) and select “Auto” if the connected TV is compatible with 1080p24 frame input.  
• Even if the connected TV is compatible with 1080p24 frame input and you set “HDMI Video Resolution” setting to  
“Auto”, when the contents of the disc are not compatible for 1080p24 frame, 1080p60 frame will be output.  
• If the picture is not output properly to the TV because of “HDMI Video Resolution” or “Component Output” setting,  
press and hold [B PLAY] on the front panel for more than 5 seconds. Both settings will be reset to the default  
automatically.  
• For video resolution of the component output, you can only select the video resolution which is currently output  
from HDMI OUT jack or “480i” if HDMI cable is connected.  
• If the video resolution for the component output and HDMI video resolution do not match, the video resolution for  
the component output will be switched to “480i”.  
• If you play back copy-protected DVD-video, 480p signal will be output from COMPONENT VIDEO OUT jacks, when  
“Component Output” setting is set to “720p” or “1080i”.  
EN  
33  
FUNCTION SETUP  
S
Audio  
Audio  
BD Audio Mode  
HDMI Audio Out  
Down Sampling  
DRC  
Mix Audio Output  
HDMI Multi(Normal)  
On  
Off  
• To select the setting items and options, refer to “ Custom” on page 30.  
• “ Quick” menu consists of the setting menus frequently used, and they are accompanied with  
.
Setting items  
BD Audio Mode  
Options  
Mix Audio Output*:  
For BD, selects whether to output the Outputs the secondary and interactive audio with primary audio if it is available.  
secondary and interactive audio with  
primary audio if it is available or only  
the primary audio. Refer to “Setting  
the BD Audio Mode” on page 28.  
HD Audio Output:  
Outputs only the primary audio. Set this mode in order to output Dolby Digital,  
Dolby Digital Plus, Dolby TrueHD, DTS or DTS-HD audio of BD through HDMI  
connection.  
HDMI Audio Out  
HDMI Multi(Normal)*:  
The multi-channel audio signals are output from HDMI OUT jack with bitstream  
or LPCM.  
Sets the audio format for the  
audio output from HDMI OUT jack.  
Refer to page 35.  
HDMI Multi(LPCM):  
The multi-channel audio signals are output from HDMI OUT jack with LPCM.  
Refer to pages 37-38 for setting options.  
Audio Mute:  
Mutes the HDMI audio signal, and set the signal format from DIGITAL OUT jack.  
Refer to “Digital Out setting” on page 36 for setting options.  
Down Sampling  
On*:  
Sets the digital audio output when  
LPCM signals are converted to 48 kHz for output.  
playing back BD or DVD recorded in Set to “On” when using digital connections to an AV amplifier that is not  
LPCM.  
compatible with sampling frequencies of 96 kHz.  
Off:  
For BD and DVD recorded in LPCM without copyright protection, 2-channel  
audio signals up to 192 kHz are output as LPCM signals with no conversion.  
DRC  
On  
Sets whether to compress the range  
of sound volume (dynamic range  
control) when Dolby Digital, Dolby  
Digital Plus or Dolby TrueHD audio is  
played back.  
Off*  
*)Settings with (*) are the default.  
• Under following circumstances, “HDMI Multi(Normal)” and “HDMI Multi(LPCM)” are not available.  
- HDMI cable is not connected to HDMI OUT jack.  
- Connected TV is off.  
- Connected TV is not compatible with audio output.  
34  
EN  
FUNCTION SETUP  
HDMI Audio Out Setting  
When using HDMI connections make “HDMI Audio Out” setting in “Audio” menu according to the specifications of the  
device to be connected. Refer to page 34. Normally, set it to “HDMI Multi(Normal)” so that the unit automatically picks  
and outputs the best audio format suited to your connected device.  
Device to be connected  
“HDMI Audio Out” setting  
Output HDMI audio signal  
Dolby Digital, Dolby Digital Plus, Dolby TrueHD,  
DTS, or DTS-HD bitstream are output from HDMI  
OUT jack. Make the speaker settings on the  
connected AV amplifier, etc.  
Device compatible with Dolby Digital,  
Dolby Digital Plus, Dolby TrueHD, DTS or  
DTS-HD decoding  
HDMI Multi(Normal)  
Device compatible with 3 or more channels  
of audio inputs (not Dolby Digital, Dolby  
Digital Plus, Dolby TrueHD, DTS or DTS-HD  
compatible)  
Multi-channel audio signals are output from  
HDMI OUT jack. Make the speaker settings with  
the speaker setting items appear after you select  
“HDMI Multi(LPCM)”. Refer to page 34.  
HDMI audio will be mute, and Dolby Digital / DTS  
bitstream or LPCM will be output from DIGITAL  
OUT jack depending on “Digital Out setting”.  
Refer to page 36.  
HDMI Multi(LPCM)  
Audio Mute  
HDMI connection to a TV and digital audio  
connection (coaxial) to an AV amplifier.  
Audio signals output from HDMI OUT jack  
“HDMI Audio Out” setting  
HDMI Multi(Normal)  
HDMI Multi(LPCM)  
Media  
Recording format  
When “BD Audio  
When “BD Audio  
When “BD Audio  
When “BD Audio  
Mode” is set to “HD Mode” is set to “Mix Mode” is set to “HD Mode” is set to “Mix  
Audio Output”  
Dolby Digital  
Dolby Digital Plus  
Dolby TrueHD  
DTS  
Audio Output”  
Dolby Digital  
Dolby Digital  
Dolby Digital  
DTS  
Audio Output”  
Multi LPCM  
Audio Output”  
Multi LPCM  
Dolby Digital  
Dolby Digital Plus  
Dolby TrueHD  
DTS  
*1  
*1  
Multi LPCM  
Multi LPCM  
*2  
*2  
Multi LPCM  
Multi LPCM  
BD-video  
Multi LPCM  
Multi LPCM  
*3  
*3  
DTS-HD  
DTS-HD  
DTS  
Multi LPCM  
Multi LPCM  
LPCM  
Multi LPCM  
Dolby Digital  
DTS  
Multi LPCM  
Multi LPCM  
Multi LPCM  
Multi LPCM  
2ch LPCM  
Multi LPCM  
Dolby Digital  
DVD-video DTS  
LPCM  
2ch LPCM  
2ch LPCM  
DTS  
audio CD  
DTS-CD  
2ch LPCM  
Multi LPCM  
*1) Outputs audio signals decoded from independent substream.  
*2) Outputs audio signals decoded from Dolby Digital stream.  
*3) Outputs audio signals decoded from DTS core stream.  
• If the connected device is not compatible with the HDMI BITSTREAM, audio will be output as multi LPCM or 2-channel  
down-mixed LPCM depending on the capability of the connected device even if you select “HDMI Multi(Normal)” in  
“HDMI Audio Out” setting.  
Note  
• The audio signals from HDMI OUT jack (including the sampling frequency, the number of channels and bit length)  
maybe limited by the device that is connected.  
• Among the devices that support HDMI, some do not support audio output (e.g. projectors). In connections with  
device such as this unit, audio signals are not output from HDMI OUT jack.  
• Video and audio signals may be distorted temporarily when switching to / from the HDMI output mode.  
EN  
35  
FUNCTION SETUP  
Digital Out setting  
When “Audio Mute” is selected in “HDMI Audio Out” setting, HDMI audio signal will be mute and the audio signals  
output from DIGITAL OUT jack changes depending on “Digital Out” setting.  
Quick A HDMI Audio Out A Audio Mute A Digital Out  
Bitstream* :  
When playing back discs recorded in Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS or DTS-HD, the  
corresponding core stream (Dolby Digital or DTS) are output.  
LPCM :  
LPCM signal will be output from DIGITAL OUT jack.  
• This setting is not effective when the HDMI audio signal is output.  
Audio signals output from DIGITAL OUT (COAXIAL) jack  
For the settings in the “Digital Out” to take effect, “HDMI Audio Out” should be set to “Audio Mute”. Otherwise, the  
settings made in the “HDMI Audio Out” will have a priority, and the same signal as being output from the HDMI OUT jack  
will be output from the DIGITAL OUT jack as well. (Except that Dolby Digital will be output instead of Dolby Digital Plus  
and Dolby TrueHD, and DTS signal will be output instead of DTS-HD.)  
“Digital Out” setting  
Bitstream  
LPCM  
Media  
Recording format  
When “BD Audio  
When “BD Audio  
When “BD Audio  
When “BD Audio  
Mode” is set to “HD Mode” is set to “Mix Mode” is set to “HD Mode” is set to “Mix  
Audio Output”  
Dolby Digital  
Dolby Digital  
Dolby Digital  
DTS  
Audio Output”  
Dolby Digital  
Dolby Digital  
Dolby Digital  
DTS  
Audio Output”  
Audio Output”  
Dolby Digital  
Dolby Digital Plus  
Dolby TrueHD  
DTS  
2ch Downmix LPCM  
2ch Downmix LPCM  
2ch Downmix LPCM  
2ch Downmix LPCM  
2ch Downmix LPCM  
2ch Downmix LPCM  
2ch Downmix LPCM  
2ch Downmix LPCM  
2ch Downmix LPCM  
2ch Downmix LPCM  
2ch Downmix LPCM  
*1  
*2  
*1  
*2  
BD-video  
*3  
*3  
DTS-HD  
DTS  
DTS  
LPCM  
2ch Downmix LPCM 2ch Downmix LPCM 2ch Downmix LPCM  
Dolby Digital  
DTS  
Dolby Digital  
DTS  
2ch Downmix LPCM  
2ch Downmix LPCM  
2ch LPCM  
DVD-video  
LPCM  
2ch LPCM  
2ch LPCM  
DTS  
audio CD  
DTS-CD  
2ch LPCM  
2ch Downmix LPCM  
*1) Only the independent substream is decoded.  
*2) Only the Dolby Digital substream is decoded.  
*3) Only the core substream is decoded.  
Note  
• In order to output LPCM signal from DIGITAL OUT jack while outputting the HDMI audio signal, set “HDMI Audio  
Out” setting to “HDMI Multi(LPCM)”.  
36  
EN  
FUNCTION SETUP  
Speaker setting (Available when you have HDMI cable connected to HDMI OUT jack)  
This unit allows you to enjoy multi-channel surround sound such as 7.1-channel / 5.1-channel surround. To make the  
most of its feature, set up your speakers appropriately by referring to the following table.  
How to navigate through “HDMI Multi(LPCM)”:  
1) Use [K / L] to select your desired menu item then  
press [OK].  
2) Use [K / L] to select your setting items.  
• Press [RETURN] to go back to the previous screen.  
3) Use [s / B] to select desired options. (Except for  
“Test Tone”, “Default” and setting options in  
“Speaker Size” setting.)  
Front speaker (left)  
Front speaker (right)  
Subwoofer  
For setting options in “Speaker Size” setting:  
Press [OK] to select desired options.  
Center speaker  
For “Test Tone”:  
Use [s / B] to select “Off”, “Manual” or “Auto”,  
then press [OK].  
• The test tone will be output. If you select “Manual”,  
use [K / L] to select desired speaker, then use  
[s / B] to adjust the volume. If you select “Auto”,  
use [s / B] to adjust the volume of the speaker that  
outputs the test tone.  
Surround  
Surround  
speaker (right)  
speaker (left)  
• If you want to stop the test tone, press [RETURN].  
Surround  
back speaker  
(right)  
Surround  
back speaker  
(left)  
For “Default”:  
Press [OK] to reset to the default.  
4) Press [SETUP] to exit.  
e.g.) basic layout with 7.1-channel surround system  
<Speaker setting for the audio signal output from HDMI OUT jack>  
Quick A HDMI Audio Out A HDMI Multi(LPCM)  
Custom A Audio A HDMI Audio Out A HDMI Multi(LPCM)  
Menu  
Speaker Size  
Setting items  
Front  
Options  
Descriptions  
Large*  
Small  
Large*  
Small  
On  
Large*  
Small  
Large*  
Small  
Large:  
Selects the desired  
speaker to set. Then  
change the setting by  
referring to the  
For the large speakers with strong low  
frequency reproduction capabilities.  
Small:  
For the small speakers which do not provide  
strong bass sound.  
You cannot change the setting of  
“Subwoofer”.  
Speakers which are not supported by the  
connected device will be displayed in gray.  
Center  
Subwoofer  
Surround  
descriptions.  
Surround Back  
Default  
Select “Default”, then press [OK] to reset  
“Speaker Size” setting to the default.  
EN  
37  
FUNCTION SETUP  
Menu  
Setting items  
Options  
Descriptions  
Channel Level  
Tests or sets the  
volume for each  
speaker.  
Test Tone:  
Off*  
Manual  
Auto  
Select “Off” to deactivate “Test Tone”.  
Select “Manual”, then press [OK] to manually  
set the volume for the desired speaker.  
Select “Auto”, then press [OK] to  
automatically output the test tone from each  
speaker.  
“Test Tone” is the test  
tone which can be  
output from the  
speakers so you can  
adjust the volume for  
each speaker.  
Front Lch  
0dB to -12dB  
(0dB*)  
0dB to -12dB  
(0dB*)  
0dB to -12dB  
(0dB*)  
0dB to -12dB  
(0dB*)  
If you have selected “Manual” in “Test Tone”,  
select the desired speaker to set and adjust  
the volume for the selected speaker.  
If you select “Auto” in “Test Tone”, test tone  
will automatically be output in order. Adjust  
the volume of the speaker that outputs the  
test tone.  
Center  
Subwoofer  
Front Rch  
Surround Rch  
Surround Back Rch  
Surround Back Lch  
Surround Lch  
Default  
0dB to -12dB  
(0dB*)  
0dB to -12dB  
(0dB*)  
0dB to -12dB  
(0dB*)  
0dB to -12dB  
(0dB*)  
Select “Default”, then press [OK] to reset  
“Channel Level” setting to the default.  
Delay Time  
Distance  
Feet*  
Meters  
Set the desired measure system. This measure  
system will be used for “Delay Time” setting.  
Press [OK] to switch the settings.  
This is a parameter for  
optimizing the timing  
at which the sound  
outputs from the  
Front  
0ft to 60ft (12ft*)  
(0 m to 18 m (3.6 m*)) to the speaker to get the ideal delay time.  
0ft to 60ft (12ft*)  
(0 m to 18 m (3.6 m*))  
0ft to 60ft (10ft*)  
(0 m to 18 m (3.0 m*))  
0ft to 60ft (10ft*)  
(0 m to 18 m (3.0 m*))  
Select the distance from the listening position  
speakers according to  
the distance from the  
listening position.  
Center  
Surround  
Surround Back  
Default  
Select “Default”, then press [OK] to reset  
“Delay Time” setting to the default.  
*)Settings with (*) are the default.  
• For “Speaker Size” setting, the settings of each speaker size may be adjusted automatically corresponding to each  
setting. (e.g. If “Front” is set to “Small”, you cannot set “Center”, “Surround”, and “Surround Back” to “Large”.)  
• For “Delay Time”, the difference between the value of the “Front”, “Surround” and “Surround Back” setting cannot  
exceed 15 ft (4.5m), and the difference between the value of the “Front” and “Center” setting cannot exceed 5 ft  
(1.5m).  
• For “Delay Time”, the value of the “Center”, “Surround” and “Surround Back” setting cannot exceed the value of the  
“Front” setting.  
• For “Delay Time”, the setting of “Center”, “Surround” and “Surround Back” will be changed automatically to the setting  
value of the “Front”. (e.g. If the “Front” is set to 60ft (18m), the setting of “Center”, “Surround” and “Surround Back” will  
be changed to 60ft (18m) as well.)  
38  
EN  
FUNCTION SETUP  
S
Parental  
For  
first  
use  
Ratings control allows you to set a limit, which prevents your children from viewing inappropriate materials. Playback  
will be stopped if the ratings exceed the levels you set, and it will require you to enter a password before playing back  
the disc.  
Parental  
BD Rating Level  
DVD Rating Level  
Password Change  
All  
All  
1 Use [K / L] to select , then press [OK].  
2 Use [Number buttons] to enter your 4-digit password.  
For the first time use: Use [Number buttons] to enter any 4-digit number (except for 4737), then press [OK]. That  
number will be used as the password from the second time. Record your password in case you forget it.  
• If you forget the password, enter [4], [7], [3], [7]. The password will be cleared and rating level will be set to “All”.  
• While you input the password, press [CLEAR] to clear the number, then re-enter the password.  
3 Proceed to A – C  
A) BD Rating Level  
1) Use [K / L] to select “BD Rating Level”, then press [OK].  
2) Use [K / L] to select your desired option, then press [OK].  
“All”:  
“Age Setting”:  
To release the limitation.  
To set the age limitation.  
• After selecting “Age Setting”, use [Number buttons] to enter the age from 0 – 254.  
(e.g. for age 15, press [0], [1], [5])  
3) Press [SETUP] to exit.  
B) DVD Rating Level  
1) Use [K / L] to select “DVD Rating Level”, then press [OK].  
2) Use [K / L] to select your desired level, then press [OK].  
3) Press [SETUP] to exit.  
RATING EXPLANATIONS  
All  
: Parental Control is inactive; all discs can played back.  
: DVD software of any grades (adult / general / children) can be played back.  
: No one under 18 admitted.  
: Restricted; under 18 requires accompanying parent or adult guardian.  
: Parental guidance recommended.  
: Unsuitable for children under 13.  
: Parental guidance suggested.  
: General audience.  
: Suitable for children.  
8 [Adult]  
7 [NC-17]  
6 [R]  
5 [PGR]  
4 [PG-13]  
3 [PG]  
2 [G]  
1 [Kid Safe]  
C) Password Change  
1) Use [K / L] to select “Password Change”, then press [OK].  
2) Enter a new 4-digit password, then press [OK].  
3) Press [SETUP] to exit.  
EN  
39  
FUNCTION SETUP  
S
Others  
Others  
Angle Icon  
On  
On  
Auto Power Off  
HDMI CEC  
Off  
Disc  
Media Select  
Software Update  
• To select the setting items and options, refer to “ Custom” on page 30.  
• “ Quick” menu consists of the setting menus frequently used, and they are accompanied with  
.
Setting items  
Options  
Angle Icon  
On*:  
The angle icon appears on the TV screen when playing back the scene with  
various angle.  
Off:  
The angle icon disappears on the TV screen.  
Auto Power Off  
On*:  
If this unit is left with no activity for more than 30 minutes, this unit turns off  
automatically.  
Off:  
Sets off the auto power off.  
HDMI CEC  
Sets whether to utilize the HDMI CEC  
function. Refer to page 41.  
On  
Off*  
Media Select  
Selects the media to playback.  
Disc*:  
Select this when you play back a disc.  
SD Card:  
Select this when you play back an SD Memory Card.  
Software Update  
Allows you to update this unit’s  
firmware. Refer to page 42.  
Current Version:  
Indicates the current firmware version.  
Disc Update:  
Allows you to update this  
unit’s firmware using a disc.  
No*  
Yes  
40  
EN  
FUNCTION SETUP  
S HDMI CEC  
HDMI CEC allows integrated system control over HDMI and is part of the HDMI standard.  
This function may not work properly depending on a device to be connected.  
When “HDMI CEC” setting is set to “On”, functions listed below will be available.  
One Touch Play  
When this unit is turned on, the TV also is turned on and the appropriate external input channel will be selected  
automatically. The appropriate external input channel can also be selected on your TV automatically when you press  
[B (play)], [H (skip)], [G (skip)], [Number buttons], [DISPLAY], [TOP MENU], or [POP MENU / MENU] when the  
unit’s power is on. (Buttons other than [B (play)] works only with discs inserted.)  
Standby  
When you press and hold [STANDBY-ON Q] for 2 seconds, it turns off the power of the TV first and then turns off the  
power of this unit also.  
When the connected HDMI CEC compatible display device is turned off, this unit may also turn off together.  
System Information  
Get & Set Menu Language  
The unit recognizes the OSD language set for the TV and automatically sets the same language as the player menu  
language (OSD menu language) for this unit.  
• This feature is available only when “Auto(XXXX)” is selected in “Player Menu” in the setup menu. (Refer to “Player Menu”  
on page 31.)  
S Current Version  
You can confirm the current software version.  
1 Use [K / L] to select  
, then press [OK].  
2 Use [K / L] to select “Software Update”, then press [OK].  
3 Use [K / L] to select “Current Version”, then press [OK].  
Others  
Current Version  
Current Version  
x.xxx  
If you wish to check latest update  
or other product information,  
please check our Website.  
4 Press [OK] or [RETURN] to exit.  
Note  
EN  
41  
FUNCTION SETUP  
S Software Update  
This unit lets you update the firmware yourself using a firmware update disc.  
To update the firmware, you must first download the latest firmware to a disc, then execute “Software Update”.  
1 Prepare a firmware update disc:  
direction described on the site.  
• Use a blank disc and download one firmware per disc.  
• For more details on how to download the firmware, please refer to the site.  
2 Use [K / L] to select  
, then press [OK].  
3 Use [K / L] to select “Software Update”, then press [OK].  
Others  
Angle Icon  
On  
On  
Off  
Auto Power Off  
HDMI CEC  
Media Select  
Disc  
Software Update  
4 Use [K / L] to select “Disc Update”, then press [OK].  
• Confirmation message will appear.  
5 Use [K / L] to select “Yes”, then press [OK].  
Others  
Disc Update  
Software Update?  
No  
Yes  
Software Update  
Please insert a disc for software update.  
If you want to exit update, please 'RETURN'.  
• Disc tray will open automatically.  
6 Insert the firmware update disc created at step 1.  
• When the disc is loaded, firmware version information and a confirmation message will appear.  
Software Update  
Loading Disc...  
42  
EN  
FUNCTION SETUP  
7 Use [s / B] to select “Yes”, then press [OK].  
• Loading of the firmware will start.  
Software Update  
The indicators blinks for this procedure.  
Current Version  
Insert Version  
: 1.000  
: 1.001  
1. Start  
Select ‘Yes’ and press ‘OK’ button to start updating.  
Press ‘No’ to exit software update.  
DISC IN  
PLAY  
STANDBY-ON  
Yes  
No  
2. Loading / Updating  
Software Update  
2. Updating  
1. Loading  
DISC IN  
PLAY  
STANDBY-ON  
DISC IN  
PLAY  
STANDBY-ON  
Loading Software...  
If you want to exit update, press ‘RETURN’.  
Software Update  
2. Updating  
1. Loading  
Updating Software...  
Please wait for a few minutes.  
Do not unplug the AC cord or interrupt updating process.  
When Update is completed unit will automatically turn Off.  
Update disc will eject after unit automatically turns back on.  
3. Finish  
(Success)  
Updating:  
Success :  
and  
and  
flash alternately.  
remain on.  
DISC IN  
PLAY  
PLAY  
STANDBY-ON  
STANDBY-ON  
(Error)*  
DISC IN  
* If the indicator shows Error...  
1) Unplug the AC power cord and turn the unit again.  
2) Confirm the current firmware version.  
3) If the firmware version is updated, the software update has succeeded. If not, please follow the steps 2 to 8 on  
pages 42-43.  
8 After the firmware update finishes, this unit will restart, and eject the disc automatically.  
• Software updating is now complete. Please take out the firmware update disc.  
Note  
• You can check the current firmware version in “Current Version” in “Software Update” menu.  
• Please do not unplug the AC power cord while executing “Software Update”.  
• All settings will remain the same even if you update the firmware version.  
EN  
43  
FUNCTION SETUP  
Initialize  
Initialize the setting or SD Memory Card.  
In stop mode, press [SETUP].  
1
2
3
Use [K / L] to select , then press  
[OK].  
Use [K / L] to select a desired option,  
then press [OK].  
“Setup”:  
Resets the setup menu to the default.  
“Format SD Card”  
(Available only when an SD Memory Card is  
inserted.):  
Initializes the SD Memory Card. After  
confirmation message appears, use [K / L]  
to select “Yes”, then press [OK].  
“Erase Saved BD-ROM Data (Player)”:  
Clears the data saved for the BD-ROM  
contents, such as BD-ROM game scores, from  
this player.  
“Erase Saved BD-ROM Data (SD Card)”  
(Available only when an SD Memory Card is  
inserted.):  
Clears the supplemental data for the BD-ROM  
playback, such as subtitle data, from the SD  
Memory Card.  
Initialize  
Setup  
Format SD Card  
Erase Saved BD-ROM Data (Player)  
Erase Saved BD-ROM Data (SD Card)  
Press [OK]. (For “Setup” and “Format  
SD Card” only)  
4
• Final confirmation message will appear. Select  
Yes”, then press [OK].  
Press [SETUP] to exit.  
5
Note  
• The setting for “Parental” will not be reset.  
Caution  
• Do not remove the SD Memory Card while executing  
the “Format SD Card” or the “Erase Saved BD-ROM  
Data (SD Card)”. It damages the card.  
44  
EN  
OTHERS  
Troubleshooting  
If the unit does not perform properly when operated as instructed in this manual, check the unit, consulting the  
following checklist.  
Problem  
Solution  
No power  
- Check if the AC cord is properly connected.  
- Unplug the AC cord once, and wait for 5-10 seconds and then plug it in again.  
No sound or picture  
Distorted picture  
- Check if the connected TV is turned on.  
- Check if the connections are made securely and correctly.  
- Check whether the connected TV or other device supports HDCP. (This unit will not  
output a video signal unless the other device supports HDCP.)  
- Check whether the output format of this unit (HDMI FORMAT) matches the  
supported input format of other connected device.  
- Sometimes a small amount of picture distortion may appear.  
This is not a malfunction.  
- Connect this unit directly to the TV. If the RCA audio / video cables are connected  
to a VCR, pictures may be distorted due to the copy right protection system.  
- Make sure the disc is compatible with this unit.  
Completely distorted picture  
or black / white picture with  
BD / DVD  
No sound or distorted sound  
- Adjust the volume.  
- Check if speakers are connected correctly.  
- Check the HDMI connections.  
- Check the settings in “Audio” menu.  
- Check the disc for fingerprints / scratches and clean with a soft cloth wiping from  
center to edge.  
Picture freezes momentarily  
during playback  
- Clean the disc.  
- Clean the disc.  
Disc cannot be played back  
- Ensure the disc label is facing up.  
- Check if the disc is defective by trying another disc.  
- Cancel the ratings control or change the control level.  
- Insert a correct disc that can be played back on this unit.  
- The format of the card does not match that accepted by this unit or the card is not  
compatible.  
SD Memory Card cannot be  
read  
No return to start-up screen  
when disc is removed  
The unit does not respond to  
the remote control  
- Reset this unit by turning it off, then on again.  
- Aim the remote control directly at infrared sensor window on the front panel.  
- Reduce the distance to infrared sensor window.  
- Replace the batteries in the remote control.  
- Re-insert the batteries with their polarities (+ / - signs) as indicated.  
- To completely reset the unit, press and hold [Q STANDBY-ON] on the front panel  
for 10 seconds to shut down the unit or unplug the AC cord from the AC outlet for  
5-10 seconds.  
Buttons do not work or the  
unit stops responding  
The unit does not respond to  
some operating commands  
during playback  
The unit cannot read BD /  
DVD/ CD  
- Operations may not be permitted by the disc.  
Refer to the instructions of the disc.  
- Condensation? (Let sit 1 or 2 hours)  
- You are attempting to playback a disc other than one with one of the Logos on  
page 14.  
- Wipe the dirt off the disc or replace the disc.  
Angle does not switch  
- The angle cannot be switched for BD / DVD which do not contain multiple angles.  
In some cases multiple angles are only recorded for specific scenes.  
- Check the settings in “Parental” menu.  
Playback does not start when  
the title is selected  
The password for rating level  
has been forgotten  
- Enter the default password “4737”, then your forgotten password will be cleared.  
Note  
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this  
manual for details on correct operations.  
• Some functions are prohibited on some discs.  
EN  
45  
OTHERS  
Glossary  
Analog Audio  
Dolby TrueHD  
An electrical signal that directly represents sound.  
Compare this to digital audio which can be an electrical  
signal, but is an indirect representation of sound. See also  
“Digital Audio”.  
Dolby TrueHD is a lossless coding technology developed  
for next generation optical discs. Blu-ray Disc supports 7.1  
multi-channel surround sound output.  
DTS (Digital Theater System)  
DTS is a multi-channel surround sound system. By  
connecting to DTS decoder, you can enjoy movie dynamic  
and realistic sound like movie theater. DTS surround  
Aspect Ratio  
The width of a TV screen relative to its height.  
Conventional TVs are 4:3 (in other words, the TV screen is  
almost square); widescreen models are 16:9 (the TV screen sound technologies were developed by DTS, Inc.  
is almost twice as wide as it is high).  
DTS-HD  
BD-Java  
DTS-HD is a lossless coding technology developed as an  
With some BD which support Java applications, you can  
enjoy the interactive functions such as games or  
interactive menus.  
extension of the original DTS Coherent Acoustics format.  
Blu-ray Disc supports 7.1 multi-channel surround sound  
output.  
Blu-ray Disc (BD)  
HDMI (High-Definition Multimedia Interface)  
Blu-ray Disc is a next generation optical video disc which is A digital interface between audio and video source. It can  
capable of storing much more data than a conventional  
DVD is. The large capacity makes it possible to benefit  
from the features such as high-definition videos, multi-  
channel surround sounds, interactive menus and so on.  
transmit component video, audio, and control signal with  
one cable connection.  
JPEG (Joint Photographic Experts Group)  
JPEG is a method of compressing still picture files. You can  
copy JPEG files on BD-RE/-R, DVD, CD-RW/-R or SD Memory  
Card from a computer and play back the files in this unit.  
Chapter  
Just as a book is split up into several chapters, a title on a  
BD-video or DVD-video is usually divided into chapters.  
See also “Title”.  
PCM (Pulse Code Modulation)  
The most common system of encoding digital audio,  
found on CD and DAT. Excellent quality that requires a lot  
Component Video Output  
Each signal of luminance (Y) and component (PB/CB, PR/CR) of data compared to formats such as Dolby Digital and  
is independent to output so that you can experience  
picture Color as it is.  
MPEG audio. For compatibility with digital audio recorders  
(CD, MD and DAT) and AV amplifiers with digital inputs,  
this unit can convert Dolby Digital, DTS, and MPEG audio  
Also, due to compatibility with progressive video (525p/  
480p), you can experience higher-density picture than that to PCM. See also “Digital Audio”.  
in interlace (525i/480i).  
Region Code  
Digital Audio  
Regions associate discs and players with particular areas of  
An indirect representation of sound by numbers. During  
recording, the sound is measured at discrete intervals  
(44,100 times a second for CD audio) by an analog-to-  
digital converter, generating a stream of numbers. On  
playback, a digital-to-analog converter generates an  
analog signal based on these numbers. See also “Sampling  
Frequency” and “Analog Audio”.  
the world. This unit will only play back discs that have  
compatible region codes. You can find the region code of  
your unit by looking on the rear panel. Some discs are  
compatible with more than one region (or all regions).  
Sampling Frequency  
The rate which sound is measured by a specified interval  
to turn into digital audio data. The numbers of sampling in  
one second defines as sampling frequency. The higher the  
Dolby Digital  
The system to compress digital sound developed by Dolby rate, the better the sound quality.  
Laboratories. It offers you sound of stereo (2ch) or multi-  
channel audio.  
Title  
A collection of chapters on BD-video or DVD-video. See  
also “Chapter”.  
Dolby Digital Plus  
Dolby Digital Plus is the next generation digital audio  
compression technology developed as an extension to  
Dolby Digital. Blu-ray Disc supports 7.1 multi-channel  
surround sound output.  
Track  
Audio CD use tracks to divide up the content of a disc. The  
BD-video or DVD-video equivalent is called a chapter. See  
also “Chapter”.  
46  
EN  
OTHERS  
Language Code List  
Language  
Code  
Language  
Code  
Language  
Code  
Language  
Siswat  
Slovak [SLO]  
Slovenian  
Somali  
Spanish [SPA]  
Sundanese  
Swahili  
Code  
A-B  
French [FRE]  
Frisian  
Galician  
Georgian  
German [GER]  
Greek [GRE]  
Greenlandic  
Guarani  
Gujarati  
Hausa  
Hebrew  
Hindi  
5264  
5271  
5358  
5747  
5051  
5158  
5758  
5360  
5367  
5447  
5569  
5455  
5467  
Macedonian  
Malagasy  
Malay  
Malayalam  
Maltese  
Maori  
Marathi  
Moldavian  
Mongolian  
Nauru  
5957  
5953  
5965  
5958  
5966  
5955  
5964  
5961  
5960  
6047  
6051  
6061  
6565  
6557  
6558  
6561  
5165  
6567  
6569  
6568  
Abkhazian  
Afar  
Afrikaans  
Albanian  
Amharic  
Arabic  
Armenian  
Assamese  
Aymara  
Azerbaijani  
Bashkir  
Basque  
Bengali;Bangla  
Bhutani  
Bihari  
Bislama  
4748  
4747  
4752  
6563  
4759  
4764  
5471  
4765  
4771  
4772  
4847  
5167  
4860  
5072  
4854  
4855  
4864  
4853  
5971  
4851  
Swedish [SWE]  
T
Tagalog  
Tajik  
Tamil  
Tatar  
Telugu  
Thai  
Tibetan  
Tigrinya  
Tonga  
Tsonga  
Turkish [TUR]  
Turkmen  
Twi  
6658  
6653  
6647  
6666  
6651  
6654  
4861  
6655  
6661  
6665  
6664  
6657  
6669  
Nepali  
Norwegian [NOR]  
Hungarian [HUN]  
O-R  
Occitan  
Oriya  
Oromo (Afan)  
Panjabi  
Pashto;Pushto  
Persian  
Polish [POL]  
Portuguese  
[POR]  
Quechua  
Rhaeto-  
Romance  
Romanian  
[RUM]  
Russian [RUS]  
I-K  
Icelandic [ICE]  
Indonesian  
Interlingua  
Interlingue  
Inupiak  
6149  
6164  
6159  
6247  
6265  
5247  
6258  
6266  
5565  
5560  
5547  
5551  
5557  
5347  
5566  
5647  
5669  
5760  
5765  
5757  
6469  
5771  
6460  
5761  
5767  
Breton  
Bulgarian [BUL]  
Burmese  
Byelorussian  
Irish [IRI]  
Italian [ITA]  
Japanese [JPN]  
Javanese  
Kannada  
Kashmiri  
Kazakh  
Kinyarwanda  
Kirghiz  
Kirundi  
Korean [KOR]  
Kurdish  
C-E  
Cambodian  
Catalan  
Chinese [CHI]  
Corsican  
6367  
6459  
5759  
4947  
7254  
4961  
5464  
4965  
5047  
6058  
5160  
5161  
5166  
U-Z  
Ukrainian  
Urdu  
6757  
6764  
6772  
6855  
6861  
4971  
6961  
7054  
5655  
7161  
7267  
6461  
6467  
Uzbek  
Croatian  
Vietnamese  
Volapuk  
Welsh  
Wolof  
Xhosa  
Yiddish  
Yoruba  
Zulu  
Czech [CZE]  
Danish [DAN]  
Dutch [DUT]  
English [ENG]  
Esperanto  
S
Samoan  
Sangho  
Sanskrit  
Scots Gaelic  
Serbian  
Serbo-Croatian  
Sesotho  
Setswana  
Shona  
Sindhi  
Singhalese  
6559  
6553  
6547  
5350  
6564  
6554  
6566  
6660  
6560  
6550  
6555  
L-N  
Laothian  
Latin  
Latvian;Lettish  
Lingala  
Lithuanian  
Estonian  
5861  
5847  
5868  
5860  
5866  
F-H  
Faroese  
Fiji  
5261  
5256  
5255  
Finnish [FIN]  
Note  
• If you choose a language that has a 3-letter-language code (written in bracket), the code will be displayed every  
time you change the audio or subtitle language setting on page 27. If you choose any other languages, “---” will be  
displayed instead.  
EN  
47  
OTHERS  
General  
Signal system  
NTSC color  
Power requirements  
Power consumption  
120 V AC, 60 Hz  
20 W (standby: 0.5 W)  
Dimensions (width x height x depth) 14-3/16 x 2 x 8-16/8 inches (360 x 50 x 215mm)  
Weight  
4.2 lbs. (1.9 kg)  
Operating temperature  
Operating humidity  
41°F (5°C) to 104°F (40°C)  
Less than 80 % (no condensation)  
Terminals  
Video output  
RCA jack x 1  
1 Vp-p (75)  
Component video output  
RCA jack x 3  
Y: 1 Vp-p (75)  
PB/CB: 700 mVp-p (75)  
PR/CR: 700 mVp-p (75)  
HDMI output  
HDMI jack x 1  
Video: 480p, 720p, 1080i, 1080p, 1080p24 / Audio  
L/R: 2 Vrms (output impedance: more than 1k)  
500 mVp-p (75)  
Audio output (Analog)  
RCA jack x 2  
Audio output (Digital)  
RCA jack x 1  
Note  
• The specifications and design of this product are subject to change without notice.  
48  
EN  
OTHERS  
Disc handling  
Maintenance  
Servicing  
• Please refer to relevant topics on “Troubleshooting” on  
page 45 before returning the product.  
• If this unit becomes inoperative, do not try to correct the  
problem by yourself. There are no user-serviceable parts  
inside. Turn the unit to the standby mode, unplug the  
power plug, and please contact 1-800-605-8610 or visit :  
• Handle the discs so that fingerprints and dust do not  
adhere to the surfaces of the discs.  
• Always store the disc in its protective case when it is not  
used.  
• Note that discs with special shapes (heart-shaped discs,  
octagonal discs, etc.) cannot be played back on this unit.  
Do not attempt to playback such discs, as they may  
damage the unit.  
IR signal check  
Cleaning the cabinet  
• Wipe the front panel and other exterior surfaces of the  
unit with a soft cloth.  
• If the remote control is not working properly, you can use  
a digital camera (including a cellular phone with built-in  
camera) to see if it is sending out an infrared signal.  
• Never use a solvent, thinner, benzene or alcohol to clean  
the unit. Do not spray insecticide liquid near the unit.  
Such chemicals may discolor the surface or damage the  
unit.  
• With a digital camera  
(including built-in cell phone cameras):  
Point a digital camera towards the  
remote control. Push any button on the  
remote control and look through the  
digital camera. If the infrared light  
appears through the camera, the remote  
control is working.  
Cleaning discs  
• When a disc becomes dirty, clean it with a cleaning cloth.  
Wipe the disc from the center to out. Do not wipe in a  
circular motion.  
• Do not use solvents such as benzine, thinner,  
commercially available cleaners, detergent, abrasive  
cleaning agents or antistatic spray intended for analog  
records.  
Cleaning the disc lens  
• If this unit still does not perform properly although you  
refer to the relevant sections and to “Troubleshooting” in  
this manual, the laser optical pickup unit may be dirty.  
Consult your dealer or an authorized service center for  
inspection and cleaning of the laser optical pickup unit.  
EN  
49  
MEMO  
50  
EN  
MEMO  
EN  
51  
LIMITED WARRANTY  
LIMITED WARRANTY  
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship  
as follows:  
DURATION:  
PARTS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date  
of original retail purchase. Certain parts are excluded from this warranty.  
LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of  
original retail purchase.  
LIMITS AND EXCLUSIONS:  
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT OR OTHER  
PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PRODUCT TO OBTAIN SERVICE  
UNDER THIS WARRANTY.  
This warranty shall not be extended to any other person or transferee.  
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing  
or if service was attempted by an unauthorized service center. This limited warranty does not apply to any  
product not purchased and used in the United States.  
This warranty only covers failures due to defects in material or workmanship which occur during normal use. It  
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or products  
not supplied by FUNAI CORP., or damage, which results from accident, misuse, abuse, mishandling,  
misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or  
office use of this product, or damage which results from fire, flood, lightning or other acts of God.  
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY  
COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.  
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT  
OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS  
PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL  
OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS  
REPRESENTATIVES IN THE UNITED STATES.  
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE CENTER.  
THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SERVICE CENTER.  
THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO PROOF  
OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIR COSTS WILL BE CHARGED.  
IMPORTANT:  
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM  
STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION  
WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.  
ATTENTION:  
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT  
PRIOR NOTICE.  
WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS:  
To obtain warranty service, you must take the product, or deliver the product freight prepaid, in either its original  
packaging or packaging affording an equal degree of protection, to any AUTHORIZED SERVICE CENTER. FUNAI  
CORP. will not reimburse you for any service done by unauthorized service providers without prior written  
approval.  
To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries, please  
contact us at:  
FUNAI SERVICE CORPORATION  
Tel: 1-800-605-8610  
2200 Spiegel Drive, Groveport, OH 43125  
E5P04UD_E5P05UD  
1VMN28573 (((((  
Printed in China  

Roadmaster 3 way Speakers RS570 680 User Manual
Pioneer Car Satellite TV System SX 3800 User Manual
Philips Stereo System MCM108 User Manual
Panasonic SDR H18 User Manual
Panasonic PALMSIGHT PV L780 User Manual
Orion Car Audio XTR62 User Manual
Olympus AZ 4 Zoom User Manual
KitchenAid KFP720BW2 User Manual
JVC KW ADV793 User Manual
JVC KD R400 User Manual