MB QUART FX4100 User Manual

FORMULA  
Installation Manual  
Lower power amplifiers will clip earlier than their more powerful cousins,  
and cause loudspeaker failure when overdriven, due to the harmonics  
generated by a clipped signal, thus overheating voice coils.  
Amplifiers should be mounted with the fins running horizontally for best  
convection cooling, to minimize overheating. Purchase the best quality  
RCA cables you can afford, for reliability and less engine noise  
interference in the audio system.  
Congratulations!  
By purchasing an amplifier from MB Quart, you have decided on a product  
of the highest technical quality. MB Quart wishes you great enjoyment with  
your amplifier. Should you have any questions about this system or other  
MB Quart products, please email us at [email protected]  
It is highly recommended that the amplifier be mounted to a board of MDF  
or other solid structure using the 4 mounting screws provided. Avoid  
mounting the amplifier to metal as this can introduce noise and other  
unwanted issues. When mounting the amplifier, ensure that it is mounted  
HORIZONTALLY, as shown in the diagram above, for optimal heat  
dissipation. Mounting amplifiers to speaker enclosures is not  
recommended as this can cause damage to the amplifier components.  
When choosing a location for mounting the amplifier, ensure that you  
check for clearance from wires, gas tank, electrical devices and brake  
lines etc.  
System Design  
The success of any car stereo system relies on several factors, such as  
the system design, execution of the installation, and system setup. Please  
remember that any system is only as good as its weakest link.  
Please remember that higher power systems are not necessarily useful  
purely for high sound pressure levels, but also to establish a headroom  
capability, to reproduce musical peaks cleanly without distortion.  
WOOD  
FX2.60 / FX4.50 / FX4.70 / FX4.100 / FX1.400 / FX1.600  
INSTALLATION INSTRUCTIONS  
General Instructions  
General:  
Run the wiring so that RCA cables are at least 18“ away from power and speaker cables. Keep RCA cables away from electrical devices in the vehicle  
that can cause electrical noise, such as electric fuel pumps, emission control modules and other on-board electronic modules.  
Power and ground connections:(See table below)  
Use a sufficient gauge power cable and ground cable using the chart below as reference to what size wire you require. Formula series amplifiers  
require at least 4 gauge power wire. In a multi amplifier system, add the total value of the manufacture recommended fusing to get your total system  
amperage. Some applications may require multiple runs of power wire to meet the system requirements. In multi amplifier systems it is advisable to  
mount a large enough fuse right at the battery, and run one or multiple +12 volt power cables to a fused distribution block near the amplifiers. It is then  
a simple matter to connect the +12 volt terminal of each amplifier to the distribution block. During this process, please ensure that the main power fuse  
is removed to avoid shorting the electrical system. The main fuse must be within 12” of the vehicles battery.  
Ground each amplifier with as short a ground lead as possible directly to the vehicle chassis using at least 4 gauge wire or equivalent to the size of the  
amplifiers’ power wire. Use a ground distribution block, if you wish, but it is extremely important to keep the main ground lead from this distribution  
block to the chassis as short as possible , not more than 12“. The ground connection integrity to the chassis is very important, and the best way to  
achieve a good, solid electrical and mechanical contact is to use a large round crimp lug, crimped and soldered to the ground cable. The next step is to  
scrape the paint off the vehicle chassis , slightly larger than the ground lug, at the connection point. Drill a clearance hole in the chassis, the same size  
as the lug hole, and use a bolt, spring washer and nut to securely fasten the ground lug. Use petroleum jelly to coat the bolt/lug connection, to prevent  
oxidization with time.  
TIP: Use the same approach when installing head units, equalizers or any audio equipment for that matter - run short individual grounds from each  
piece directly to the vehicle chassis, to minimize ground loops and system noise. All power, ground and speaker connections should be crimped and  
soldered for reliability. Make sure that none of the cable insulation can chafe against exposed metal in the vehicle, causing short circuits to the  
chassis.  
Safe connection sequence:  
After all cables are run, connect speaker wires to the speakers and amplifiers, then run and plug in RCA cables. Next, connect all power, ground, and  
remote turn on leads. Now connect all +12 volt cables to the amplifier/s and distribution blocks and fuse holders. Finally, connect the main +12 volt  
cable to the battery, with the main fuse removed, and we are almost ready to power up the system.  
Power up the system:  
The following procedure may seem like overkill, but there is nothing more frustrating when turning on a system for the first time, and it does not work  
properly immediately.  
First, make sure the head unit is off, and turn all level controls to minimum (counterclockwise), including the head unit volume control. Set all equalizers  
to 0 dB (no boost), and all crossover frequency controls at approximate frequencies, as recommended by the loudspeaker manufacturer. Set all input  
selector and crossover switches as required for the application. Remove all amplifier fuses, and insert the main fuse at the battery. If the fuse does not  
blow, you can insert the fuse in one of the amplifiers, and we are ready to turn on the system. Turn the head unit on, insert a CD, or select a radio  
station, and increase the head unit volume control. If the system sounds fine, turn off the head unit, and install fuses in the remaining amplifiers, one by  
one, till the complete system is powered up and functioning properly.  
WIRE LENGTH  
SYSTEM  
AMPERAGE  
7-10 ft.  
10-13 ft.  
13-16 ft.  
16-19 ft.  
19-22 ft.  
22-28 ft.  
35-50  
8
6
4
4
4
2
6
4
4
2
2
0
4
4
2
2
0
0
4
4
2
2
0
0
4
4
2
2
0
0
4
2
0
0
0
0
50-65  
68-85  
85-105  
105-125  
125-150  
2
INSTALLATION INSTRUCTIONS  
Settings for Best Performance  
FX2.60 / FX4.50 / FX4.70 / FX4.100  
General:  
At this point you are ready to get more specific on the settings for your amplifier.  
High Pass:  
-When in Hi Pass operation, this setting acts as a low frequency cut off for your system reproduction. The point that you set it at cuts off any frequencies from reproduction beyond this  
point. The 12 o’clock position is a great starting point. EXAMPLE: If you adjust the High Pass to 100Hz, the amplifier will not play frequencies below 100Hz but will play frequencies from  
100Hz to the highest frequency the amplifier is capable of reproducing.  
-When in Low Pass/Bandpass operation, this setting acts as a low frequency cut off for your system reproduction aka Subsonic Filter. The point that you set it at cuts off any frequencies  
from reproduction beyond this point. The 12 o’clock position is a great starting point. EXAMPLE: If you adjust the High Pass to 60Hz, the amplifier will not play frequencies below 60Hz  
but will play frequencies from 60Hz to the chosen Low Pass frequency.  
-When in Flat/Full operation, the Low Pass crossover is bypassed.  
Bass EQ:  
This setting is a fixed bass boost at 45Hz that is variable from 0-9dB. This feature provides impact to your bass, but if not adjusted correctly, it can be over used and cause damage to  
your speakers and amplifiers. It is best to slowly turn this setting clockwise until the desired punch is felt. It is not recommended to exceed the 12 o’clock position unless listening at a low  
volume or a low recording quality as this can result in high distortion and possibly clipping.  
Low Pass:  
The Low Pass control acts as a ceiling and doesn’t allow frequencies to the right of the desired setting to be reproduced. Turning the potentiometer all the way to the right is a great  
starting point. EXAMPLE: If you adjust the Low Pass to 120Hz, the amplifier will not play frequencies above 120Hz but will play frequencies from 120Hz to the chosen Hi Pass or  
Subsonic frequency.  
-When in Hi Pass operation, this setting is bypassed.  
Level Control Setup:  
Ensure that the Level is turned completely to the left prior to turning the system on. Next you should insert a CD or cassette that you are familiar with to use as a reference, and turn the  
head unit volume control to about 80% of its full setting. The system sound level will of course be very low, and the following procedures will help you to match the amplifier input  
sensitivities properly to the head unit output signal level.  
It is important to match the amplifier LEVEL input sensitivity to the Radio/CD output sensitivity. This can be located in the Radio/CD manual.  
If the Radio/CD output sensitivity is 2 volts, then adjust the amplifier LEVEL input to 2 volts.  
If you are not sure what the Radio output sensitivity is, follow these general guide lines:  
Turn the level control up slowly, till you hear distortion, then back off a few degrees on the control. If at any point your amplifier goes into protection, you will need to turn the Level to the  
left a bit and then try again. If you reach a point where the output does not increase, stop turning the Level control to the right as the amplifier/speaker combo has reached its maxx  
output in this application.  
FX1.400 / FX1.600  
General:  
At this point you are ready to get more specific on the settings for your amplifier.  
Subsonic:  
This setting acts as a low frequency cut off for your system bass reproduction. The point that you set it at cuts off any frequencies from reproduction beyond this point. The 12 o’clock  
position is a great starting point. EXAMPLE: If you adjust the Subsonic to 25Hz, the amplifier will not play frequencies below 25Hz but will play frequencies from 25Hz to the chosen Low  
Pass frequency.  
Bass EQ:  
This setting is a fixed bass boost at 45Hz that is variable from 0-12dB. This feature provides impact to your bass, but if not adjusted correctly, it can be over used and cause damage to  
your subwoofers and amplifiers. It is best to slowly turn this setting clockwise until the desired punch is felt. It is not recommended to exceed the 12 o’clock position unless listening at a  
low volume or a low recording quality as this can result in high distortion and possibly clipping.  
Low Pass:  
The Low Pass control acts as a ceiling and doesn’t allow frequencies to the right of the desired setting to be reproduced. The 12 o’clock position is a great starting point. EXAMPLE: If you  
adjust the Low Pass to 80Hz, the amplifier will not play frequencies above 80Hz but will play frequencies from 80Hz to the chosen Subsonic frequency.  
Level Control Setup:  
Ensure that the Level is turned completely to the left prior to turning the system on. Next you should insert a CD or cassette that you are familiar with to use as a reference, and turn the  
head unit volume control to about 80% of its full setting. The system sound level will of course be very low, and the following procedures will help you to match the amplifier input  
sensitivities properly to the head unit output signal level.  
It is important to match the amplifier LEVEL input sensitivity to the Radio/CD output sensitivity. This can be located in the Radio/CD manual.  
If the Radio/CD output sensitivity is 2 volts, then adjust the amplifier LEVEL input to 2 volts.  
If you are not sure what the Radio output sensitivity is, follow these general guide lines:  
Turn the level control up slowly, till you hear distortion, then back off a few degrees on the control. If at any point your amplifier goes into protection, you will need to turn the Level to the  
left a bit and then try again. If you reach a point where the output does not increase, stop turning the Level control to the right as the amplifier/subwoofer combo has reached its maxx  
output in this application.  
3
TROUBLE SHOOTING  
The key to finding the problem in a misbehaving sound system is to isolate parts of that system in a logical fashion to track down the fault.  
Descriptionof the Diagnostic system built into all MB Quart amplifiers  
The diagnostic system will shut down the amplifier, until reset by turning the head unit off, and back on. This state of affairs will be indicated by the front panel  
PROTECTLEDlighting up under the following conditions:  
1 -Ashort circuit on the loudspeaker leads.  
2 -An internal amplifier fault that causes a DCoffset on the loudspeaker output.  
Should the amplifier go into diagnostic mode, simply disconnect all RCAand speaker leads, while keeping +12 volt, power ground and remote leads connected.  
1. Nowturn the amplifier back on, and if the diagnostic LEDlights, the amplifier has an internal fault.  
2. If not, plug the RCAcables back, and reset the amplifier. If it goes into diagnostic now, the fault lies in the input, either with bad cables or source unit.  
3. If the amplifier seems fine with RCAcables plugged in, connect the speakers, one at a time, and if one of the speakers or its wiring is faulty, it will activate the  
diagnostic system.  
Amplifierheatsink overheating  
The amplifiers will shut down when the heatsink temperature reaches 80 degrees centigrade, and turn back on once the unit has cooled down below that point.  
Causes of overheating:  
1 - Inadequate cooling - relocate or remount to provide better natural airflow over the fins.  
2 - Driving high power levels into low impedances - back off on the volume control, and/or make sure you are not loading the amplifier with less than the  
recommended loudspeaker impedance.  
Low output power  
1 - Check that level controls have been set up properly.  
2 - Make sure that the battery voltage, as measured at the amplifier’s +12 volt and ground terminals, is 11 volts or more.  
3 - Check all +12 volt and ground connections.  
Fuses blowing  
1 -The use of loudspeaker impedances below the recommended minimums will draw more current - check.  
2 -Ashort on the main +12 volt cable from the battery to the vehicle chassis will cause the main fuse to blow.  
System does not turn on  
1 - Check all fuses.  
2 - Check all connections.  
3 - Measure the +12 volt and remote turn on voltages at the amplifier terminals. If these are non existent or low, take voltage measurements at fuse holders,  
distribution blocks, the head unit’s +12 volt and remote leads to localize the problem.  
Noise problems  
System noise can be divided into two categories, hiss, and electrical interference.  
Hiss, or white noise  
1 - High levels of white noise usually occurs when amplifier level controls are turned up too high - readjust according to the procedures in section ”Setting up  
systems after installation for best performance”  
2 -Another major problem that can cause excessive hiss, is a noisy head unit - unplug the amplifier input RCAcables, and if the hiss level reduces, the source unit  
is at fault.  
Electricalinterference  
The inside of an automobile is a very hostile electrical environment. The multitude of electrical systems, such as the ignition system, alternator, fuel pumps, air  
conditioners, to mention just a few, create radiated electrical fields, as well as noise on the +12 volt supply and ground. Remember to isolate the problem - first  
unplug amplifier input RCA cables, if the noise is still present, check the speaker leads, if not, plug the RCA’s back, and investigate the source driving the  
amplifier, one component at a time.  
Aticking or whine that changes with engine RPM:  
1 -This problem could be caused by radiation pickup of RCAcables too near to a fuel pump or a distributor, for instance, - relocate cables.  
2 - Check that the head unit ground is connected straight to the vehicle chassis, and does not use factory wiring for ground.  
3 -Try to supply the head unit with a clean +12 volt supply directly from the battery +, instead of using a supply from the in dash wiring/fusebox.  
Aconstant whine:  
This type of noise can be more difficult to pinpoint, but is usually caused by some kind of instability, causing oscillations in the system.  
1 - Check all connections, especially for good grounds.  
2 - Make sure that no speaker leads are shorting to exposed metal on the vehicle chassis.  
3 -RCAcables are notorious for their problematic nature, so check that these are good, in particular the shield connections.  
4
FX2.60  
OUTPUT  
INPUT  
LEVEL  
BASS EQ  
HIGH PASS  
LOW PASS  
X-OVER  
L
2-Channel Amplifiers  
POWER  
PROTECTION  
6V  
0.2V  
0dB  
9dB  
30Hz  
150Hz  
10Hz  
1.2kHz FULL HP  
LP  
R
FEATURES:  
- 1 Set of RCA inputs  
- POWER LED: Indicates the powered up and turned on condition  
- LEVEL: Variable sensitivity from 0.2V to 6V  
- BASS EQ: Adjustable 45Hz bass boost from 0dB to 9dB  
- X-OVER: Selects internal crossover functions  
- FULL: Bypasses all crossovers for full frequency operation  
- LPF: Selects the built in LOW PASS filter, variable from 30Hz to 150Hz  
- HPF: Selects the built in HIGH PASS filter, variable from 10Hz to 1.2kHz  
- PROTECTION LED: Indicates a high voltage, low voltage, short circuit,  
hard clip, over heating or DC fault condition..  
- LINE OUTPUT: Full range RCA pass through.  
2 Channel Full Range Stereo:  
Control checklist:  
Interconnect cable checklist:  
- Refer to the section “Settings for Best Performance”  
- Connect the two inputs of the amplifier to a Radio/CD with quality RCA cables.  
Switch setting checklist:  
- 1/2CH X-OVER: FULL  
Minimum final loudspeaker impedances:  
- You can also feed the SAME signal to both left and right inputs via a Y-adapter RCA cable.  
- Connect the mono speaker positive terminal to the RIGHT +, and its negative terminal to LEFT  
- as shown.  
Mono Operation:  
Here we show how to use the 2 channel amplifiers as a 1 channel unit by taking  
advantage of the mono bridging capability of all MB Quart amplifiers.  
Interconnect cable checklist:  
Switch setting checklist:  
- X-OVER: LP/BP  
- A MONO signal source is required to bridge channels 1/2, such as would be available  
from the mono sub bass output of an active crossover, whether standalone, or built into  
a head unit or equalizer. If you only have 1 set of RCA outputs from your headunit, you  
can simply connect those to the inputs for ch 1/2 and switch the X-OVER to LP/BP. The  
amplifier will auto sum the signal and provide mono output for bridged channels 1/2.  
Important: Do not be tempted to connect the hot, or positive outputs, from any source  
together to obtain a mono signal, as this could very well damage the output stage of  
that source.  
Control checklist:  
- Refer to the section “Settings for Best Performance”  
Minimum final loudspeaker impedances:  
- 4 ohm mono bridged.  
MONO LINE INPUT  
5
FX4.50 / FX4.70 / FX4.100  
4-Channel Amplifiers  
Ch 3&4  
OUTPUT  
X-OVER  
LOW PASS  
BASS EQ  
HIGH PASS  
LEVEL  
LEVEL  
INPUT  
Ch1 Ch3  
LP/BP HP  
FULL  
30Hz  
150Hz  
0dB  
X-OVER  
9dB  
10Hz  
1.2kHz  
6V  
6V  
0.2V  
0.2V  
INPUT MODE  
HIGH PASS  
PROTECTION  
POWER  
4CH  
2CH  
DUPE 3/4 HP FULL  
10Hz  
1.2kHz  
Ch2  
Ch4  
Ch 1&2  
FEATURES:  
- 2 Sets of RCA inputs  
- POWER LED: Indicates the powered up and turned on condition  
- LEVEL: Variable sensitivity from 0.2V to 6V  
- BASS EQ: Adjustable 45Hz bass boost from 0dB to 9dB  
- X-OVER: Selects internal crossover functions  
- FULL: Bypasses all crossovers for full frequency operation  
- LP: Selects the built in LOW PASS filter, variable from 30Hz to 150Hz  
- HP: Selects the built in HIGH PASS filter, variable from 10Hz to 1.2kHz  
- PROTECTION LED: Indicates a high voltage, low voltage, short circuit,  
hard clip, over heating or DC fault condition.  
- MODE: “2CH” indicates one set of RCA’s are being used. This will also pass signal to channels 3/4 through 1/2 inputs.  
“4CH” indicates connecting 2 sets of RCA’s to 1/2 and  
3/4 inputs.  
- LINE OUTPUT: Full range RCA pass through.  
4 Channel Full Range Stereo:  
Control checklist:  
Interconnect cable checklist:  
- Refer to the section “Settings for Best Performance”  
- Connect the four inputs of the amplifier to a Radio/CD with quality RCA cables.  
Switch setting checklist:  
- 1/2CH X-OVER: FULL  
Minimum final loudspeaker impedances:  
- 2 ohm per channel.  
- 3/4CH X-OVER: FULL  
MODE: “4CH” since 2 sets of RCA’s are connected.  
Important: Do not be tempted to connect the hot, or positive outputs, from any source together  
to obtain a mono signal, as this could very well damage the output stage of that source.  
- It is necessary to feed the SAME signal to both left and right inputs via a Y-adapter RCA cable.  
- Connect the mono speaker positive terminal to the Ch4 +, and its negative terminal to Ch3 - as  
shown.  
2 or 3 Channel System:  
Here we show how to use the 4 channel amplifiers as a 3 channel unit by taking  
advantage of the mono bridging capability of all MB Quart amplifiers. In order to create  
a 2 channel system, simply follow the example to also mono bridge channel pair 1/2.  
Interconnect cable checklist:  
Switch setting checklist:  
- 1/2CH X-OVER: FULL  
- 3/4CH X-OVER: LP  
Control checklist:  
- Refer to the section “Settings for Best Performance”  
Minimum final loudspeaker impedances:  
- 2 ohm per channel in stereo mode.  
- 4 ohm mono bridged.  
- Connect the inputs of channel pair 1/2 to a suitable stereo source, e.g. a head unit  
with good quality RCA cables.  
- A MONO signal source is required to bridge channel pair 3/4, such as would be  
available from the mono sub bass output of an active crossover, whether standalone, or  
built into a head unit or equalizer. If you only have 1 set of RCA outputs from your  
headunit, you can simply connect those to the inputs for ch 1/2 and switch the MODE to  
2ch. The amplifier will auto sum the signal and provide mono output for bridged  
channels 3/4.  
STEREO LINE INPUT  
MONO LINE INPUT  
6
FX1.400 / FX1.600  
Mono Amplifiers  
OUTPUT  
INPUT  
REMOTE  
L
BASS BOOST  
SUBSONIC  
LOW PASS  
LEVEL  
POWER  
PROTECT  
R
0dB  
12dB  
10Hz  
40Hz  
40Hz  
300Hz  
6V  
0.2V  
FEATURES:  
- 1 Set of RCA inputs  
- POWER LED: Indicates the powered up and turned on condition  
- LEVEL: Variable sensitivity from 0.2V to 6V  
- BASS EQ: Adjustable 45Hz bass boost from 0dB to 12dB  
- SUBSONIC: Variable from 10Hz to 40Hz  
- LOW PASS: Variable from 40Hz to 300Hz  
- PROTECT LED: Indicates a high voltage, low voltage, short circuit,  
hard clip, over heating or DC fault condition.  
- LINE OUTPUT: Full range RCA pass through.  
Interconnect cable checklist:  
Connect the inputs to a suitable source, e.g. a head unit with good quality RCAcables.  
Controlchecklist:  
Refer to the section“Settings for Best Performance”  
Use at least #14 gauge speaker wiring. The amps have dual speaker terminals,  
simplifying the hookup of multiple speakers.These amps are mono, 1 channel, amplifiers  
which have multiple positive and negative connections for ease of wiring. The 2 positives  
are the same internally and the 2 negatives are the same internally.  
Minimum final loudspeakerimpedance: 2-Ohm.  
Warning: The mono amps are 4 & 2-Ohm stable only.  
They are not 1-Ohm stable.  
MONO  
SUBWOOFER  
MIN  
MBQR-2  
MAXX  
TO BATTERY + 12 Volts  
VIA FUSE  
REMOTE TURN-ON  
DESIGNATED  
MONO OUTPUT  
FROM HEAD UNIT  
CHASSIS GROUND  
2-Ohms each minimum  
FUSE  
7
OEM Integration  
Accessories  
MX-1 Premium High To Low Level Converter  
MX-3 Bass Controller  
* Converts High Level OEM speaker wires to Ultra Clean RCA  
Low Level Outputs  
* High Level Inputs: Accepts all types of High level Inputs  
including floating ground and high voltages up to 30 volts.  
* Audio Signal Sense / Hardwire Turn-On: Audio sense detects  
music signals from the OEM wires and activates the MX-1. As  
an option, the module also offers a remote turn-on wire.  
* Parametric Bass EQ: Features Bass Boost, adjustable Band  
Width (wide & narrow), Low Pass and Subsonic Filter.  
* Clipping Indicators: Visually indicates audio signals Pre-Clip,  
Soft Clip and Hard Clip  
* Balanced Line Output: Ultra clean DIN variable high voltage  
output for driving mono amps.  
* Remote Output: Driver circuit to turn on amplifier when  
module activates.  
* Parametric Bass EQ: Provides a wide array of subwoofer output signal  
shaping controls to enhance bass response and sound quality including  
Bass Boost, adjustable Bandwidth (wide and narrow), Low Pass and  
Subsonic Filter.  
* Accepts a wide range of incoming music signal levels while  
accommodating all types of head units and signal processors and  
controlling the output level to the amp to maximize a signal strength up to  
9 volts.  
* Clipping Indicators: Visual clipping indicators provide indication of  
damaging clipped signals to help protect the subwoofer(s) and amplifier.  
Includes pre-clip, soft-clip and full-clip indications.  
* Music Shaping: Shapes the music signal to achieve deep bass notes as  
low as 15Hz.  
* Bass Remote: Features for subwoofer Level control with built-  
in clipping indicators.  
* Input & Output Level Control: Allows for gain matching both  
radio and amplifier audio signals.  
* Bass Remote: Included bas Remote features built-in clipping indicators  
allows direct bass control from in-dask or under-dash.  
MX-2 Deluxe High To Low Level Converter  
MX-4 Add A Sub High To Low Level Converter  
* Converts High Level OEM speaker wires to Ultra Clean RCA  
Low Level Outputs  
* Converts High Level OEM speaker wires to Ultra Clean RCA Low Level  
Outputs  
* High Level Inputs: Accepts all types of High level Inputs  
including floating ground and high voltages up to 30 volts.  
* Audio Signal Sense / Hardwire Turn-On: Audio sense detects  
music signals from the OEM wires and activates the MX-2. As  
an option, the module also offers a remote turn-on wire.  
* High Level Inputs: Accepts all types of High level Inputs including  
floating ground and high voltages up to 30 volts.  
* Audio Signal Sense / Hardwire Turn-On: Audio sense detects music  
signals from the OEM wires and activates the MX-4. As an option, the  
module also offers a remote turn-on wire.  
* Remote Output: Driver circuit to turn on amplifier when module * Remote Output: Driver circuit to turn on amplifier when module activates.  
activates.  
9
Check out our videos of new products,  
events and technical tutorials at  
PART#S111  
FX2.60 / FX4.50 / FX4.70 / FX4.100 / FX1.400 / FX1.600  

Pioneer Car Video System XV HTD1 User Manual
Philips Car Stereo System CE132 User Manual
Pass Labs X2605 User Manual
Omega OSD10 User Manual
Nikon Coolpix 7600 User Manual
Nikon 2161B User Manual
Kenwood KVT 512 User Manual
Kenwood KRC 679R User Manual
Kenwood DNX9140 User Manual
Kenwood DDX318 User Manual