Life Fitness C9I User Manual

95Ci, 93C, 90C, C9i, C7  
Upright Exercise Bikes  
Assembly Instructions  
IMPORTANT SAFETY INSTRUCTIONS!  
DO NOT locate the Exercise Bike outdoors, near swimming pools, or in areas of high humidity.  
DO NOT operate your Exercise Bike if it has been dropped, damaged, or even partially immersed  
in water. Contact Life Fitness Customer Support Services at the number in the Operation Manual.  
DO NOT locate the Exercise Bike any closer than 30 inches ( 76 cm ) to a television set.  
DO NOT locate additional Exercise Bike any closer than a minimum of 42 inches (107 cm) from  
center to center to avoid interference (cross talk) between Heart Rate monitors.  
DO keep the area around your Exercise Bike clear of any obstructions, including walls and furniture.  
DO verify the contents of the delivery carton against the accompanying Parts Listing prior to setting  
the cartons and shipping material aside. If any parts are missing, contact Life Fitness Customer  
Support Services at the number listed in the Operation Manual. Save the shipping cartons in case of  
return.  
DO read the entire Operation Manual prior to attempting to operate this machine as this is essential  
for proper use.  
NE PAS placer le vélo d’exercice allongé Lifecycle à l’extérieur, près d’une piscine ou dans un  
endroit très humide.  
NE PAS faire fonctionner le vélo d’exercice allongé Lifecycle s’il est tombé, s’il a été endommagé ou  
s’il a été partiellement plongé dans l’eau. Téléphoner au service après-vente de Life Fitness dont le  
numéro figure sur la couverture arrière du guide d’installation.  
NE PAS placer le vélo d’exercice allongé Lifecycle à moins de 76 cm (30 po) d’un poste de  
télévision.  
MAINTENIR la zone autour du vélo d’exercice allongé Lifecycle libre de toute obstruction, y compris  
murs et meubles.  
VÉRIFIER si l’emballage contient toutes les pièces de la liste jointe avant de le mettre de côté. Si des  
pièces manquent, téléphoner au service après-vente de Life Fitness dont le numéro figure sur la  
couverture arrière du guide d’installation. Conserver l’emballage au cas où l’appareil devrait être  
renvoyé.  
LIRE le manuel de l’utilisateur tout entier avant d’essayer de faire fonctionner cet appareil. Ceci est  
indispensable à son utilisation correcte.  
TOOLS REQUIRED FOR ASSEMBLY...Phillips screwdriver, T-45 Torx Driver, T-20 Torx Driver  
PARTS DESCRIPTION  
1
Torx Button Mounting Bolt  
3/8-16 x 3/4”  
Qty: 8  
2
Phillips Pan Head Screw (Model 95Ci / 93C / C9i ) Qty: 12  
8-18 x 5/8”  
(Model 90C / C7 )  
Qty: 8  
3
5
7
Accessory Tray  
Qty: 1  
Qty: 1  
Qty: 1  
4
6
8
Console Assembly  
Qty: 1  
Top Polar Cover  
Bottom Polar Cover  
Qty: 1  
Qty: 1  
Left Seat Post Shroud  
(Model 95Ci / 93C / 90C)  
Left Pedal Strap  
Right Seat Post Shroud  
(Model 95Ci / 93C / 90C)  
9
Qty: 1  
Qty: 1  
10 Right Pedal Strap  
Qty: 1  
Qty: 1  
11  
Handlebar  
12 9 Volt Alkaline Battery  
(Model 90C / C7)  
13  
15  
Polar Receiver  
Qty: 1  
14 Polar Receiver Sleeve  
Qty: 1  
(Model 95Ci / 93C / C9i / C7 / International 90C)  
(Model 95Ci / 93C / C9i / C7 / International 90C)  
Torx / Standard Screw  
#8-18 x 3/4”  
Qty: 1  
(Model 95Ci / 93C / 90C)  
1
2
15  
1”  
2”  
3”  
4”  
5”  
5
1
4
11  
12  
6
2
2
3
8
2
7
1
15  
1. Locate the BOTTOM POLAR COVER (#6). Position the cover  
as shown with the notch of the center hole facing downward.  
Slide the BOTTOM POLAR COVER down over the UPPER  
CONSOLE SUPPORT TUBE (A) until it rests against the  
FRONT TUBE EXTENSION (B).  
4
2. Position the HANDLEBAR (#11) as shown near the UPPER  
12  
CONSOLE SUPPORT TUBE (A).  
3. Models 95Ci and C9i Only  
5
Connect the 2-PIN HEART RATE CONNECTOR (2P) leading  
from the HANDLEBAR (#11) center to the 2-PIN HEART  
RATE CONNECTOR (2P) leading from the UPPER  
CONSOLE SUPPORT TUBE (A).  
3
2
4. Carefully slide the HANDLEBAR MOUNTING FLANGES (C)  
11  
into the UPPER CONSOLE SUPPORT TUBE (A).  
NOTE: BE CAREFUL NOT TO PINCH THE HEART RATE  
CABLE WHEN INSERTING THE HANDLEBAR FLANGES  
(C) INTO THE UPPER CONSOLE SUPPORT TUBE (A).  
5. Secure the HANDLEBAR (#11) to the UPPER CONSOLE  
SUPPORT TUBE (A) using four MOUNTING BOLTS (#1).  
Tighten the SCREWS to 15-20 ft. lbs.  
C
2P  
6. Models 95Ci, 93C, C9i, and C7 Only  
2P  
E
6
Insert the POLAR RECEIVER (#13) into the polar receiver  
receptacle located at the center of the UPPER CONSOLE  
SUPPORT TUBE (A). Slide the POLAR RECEIVER SLEEVE  
(#14) over the POLAR RECEIVER covering the entire POLAR  
RECEIVER.  
2
1
1
D
2
14  
7. Locate the TOP POLAR COVER (#5). Slide the BOTTOM  
POLAR COVER (#6) upward toward the HANDLEBAR (#11)  
until it contacts the HANDLEBAR. Position the TOP POLAR  
COVER over the POLAR RECEIVER (#13) and HANDLEBAR  
and align it to the BOTTOM POLAR COVER. Secure the TOP  
POLAR COVER to the BOTTOM POLAR COVER using four  
PHILLIPS SCREWS (#2) as shown.  
13  
B
A
8. Models 95Ci, 93C, and C9i Only  
Align the ACCESSORY TRAY (#3) to the bottom of the  
DISPLAY CONSOLE (#4) as shown. Secure the  
ACCESSORY TRAY to the DISPLAY CONSOLE using four  
PHILLIPS SCREWS (#2).  
8
F
9. Models 90C and C7 Only  
7
Remove the BATTERY DOOR located on the back of the  
DISPLAY CONSOLE (#4). Locate the supplied 9-VOLT  
BATTERY (#12) and connect it to the battery lead. Place the  
BATTERY into the DISPLAY CONSOLE and replace the  
BATTERY DOOR.  
15  
10. Position the DISPLAY CONSOLE (#4) above the MOUNTING  
BRACKET (D) as shown. Attach all CONNECTORS (E)  
leading from the DISPLAY CONSOLE MOUNTING BRACKET  
to the corresponding CONNECTORS located on the back of  
the DISPLAY CONSOLE.  
11. Attach the DISPLAY CONSOLE (#4) to the DISPLAY  
CONSOLE MOUNTING BRACKET (D) using four SCREWS  
(#2).  
NOTE: BE CAREFUL NOT TO PINCH ANY CABLES WHEN  
SECURING THE DISPLAY CONSOLE (#4) TO THE  
DISPLAY CONSOLE MOUNTING BRACKET (D).  
Tighten the screws securely.  
12. Models 95Ci, 93C, and 90C Only  
10  
Locate the USER LEFT AND RIGHT SEAT POST COVERS  
(#7 & #8). Position the USER LEFT SEAT POST COVER (#7)  
below the seat covering the ADJUSTMENT LEVER (F) as  
shown. Interlock the two tabs of the USER RIGHT SEAT  
POST COVER (#8) to the corresponding slots of the USER  
LEFT SEAT POST COVER and pivot it forward to meet the  
USER LEFT SEAT POST COVER enclosing the SEAT  
ADJUSTMENT LEVER. Secure the SEAT POST COVERS  
together using one SCREW (#15).  
13. Locate the RIGHT PEDAL STRAP (#10) marked with an “R”.  
Attach the RIGHT PEDAL STRAP to the RIGHT PEDAL (G)  
with the double slot on the inward pedal strap tab looping  
upward and attaching to the outward pedal strap tab. Repeat  
for the LEFT PEDAL STRAP (#9) marked with an “L”.  
G
PRE-OPERATION CHECKLIST  
Ensure that the console support screws are tight.  
Make sure the Exercise Bike is properly leveled and stable.  
Ensure that the Leveler Jam Nuts are tight.  
Read the entire Operation Manual before using the Exercise Bike.  
Before attempting to operate your Exercise Bike, it is imperative that you familiarize yourself with the  
contents of the Operation Manual. If your Exercise Bike does not respond as described in the OPERATION  
MANUAL, contact the nearest Life Fitness service center as listed in the Operation Manual.  
©2003 Life Fitness, a division of Brunswick Corporation. All rights reserved. Life Fitness is trademark of Brunswick Corporation.  
Polar is a registered trademark of Polar Electro, Inc. MO51-00K63-A081 06.03  

Rockford Fosgate RFB2122 User Manual
Pelco Camera Lens TVJ6MS 1 User Manual
Panasonic Blu ray Player BDP 440 User Manual
Olympus TELECONVERTER EC 14 User Manual
Nikon 98793 User Manual
Magic Chef MCWC30M User Manual
Lochinvar KNIGHT 801 User Manual
KitchenAid KUWS24RSSS01 User Manual
KitchenAid 4KFP750WH1 User Manual
JVC XMD100 User Manual