Legacy Car Audio Car CD Player User Manual

OWNER’S MANUAL  
MANUALLY TUNED SYNTHESIZER STEREO RADIO  
WITH COMPACT DISC PLAYER DIGITAL  
INSTALLATION  
Notes:  
• Choose the mounting location where the unit will not interfere with the normal driving  
function of the driver.  
• Before finally installing the unit, connect the wiring temporarily and make sure it is  
all connected up properly and the unit and the system work properly.  
• Use only the parts included with the unit to ensure proper installation. The use of  
unauthorized parts can cause malfunctions.  
• Consult with your nearest dealer if installation requires the drilling of holes or other  
modifications of the vehicle.  
• Install the unit where it does not get in the driver’s way and cannot injure the  
passenger if there is a sudden stop, like an emergency stop.  
• If installation angle exceeds 30˚ from horizontal, the unit might not give its optimum  
performance.  
30˚  
• Avoid installing the unit where it would be subject to high temperature, such as from  
direct sunlight, or from hot air, from the heater, or where it would be subject to dust,  
dirt or excessive vibration.  
DIN FRONT/REAR-MOUNT  
This unit can be properly installed either from “Front” (conventional DIN Front-mount)  
or “Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of  
the unit chassis). For details, refer to the following illustrated installation methods.  
DIN FRONT-MOUNT (Method A)  
Installing the unit  
1
1. Dashboard  
2
182  
2. Holder  
After inserting the holder into the  
dashboard, select the appropriate tab  
according to the thickness of the  
dashboard material and bend them  
inwards to secure the holder in place.  
53  
3
3. Screw  
(Fig. 1)  
3
1. Dashboard  
2. Nut (5mm)  
1
7
6
3. Spring washer  
4. Screw (5 x 25mm)  
5. Screw  
4
5
2
3
6. Strap  
Be sure to use the strap to secure the  
back of the unit in place. The strap can  
be bent by hand to the desired angle.  
(Fig. 2)  
7. Plain washer  
Removing the unit  
1. Frame  
1
2. Insert fingers into the groove in the front  
of frame and pull out to remove the frame.  
(When re-attaching the frame, point the  
side with a groove downwards and attach  
it.)  
2
3
3. Lever  
Insert the levers supplied with the unit  
into the grooves at both sides of the unit  
as shown in figure until they click. Pulling  
the levers makes it possible to remove  
the unit from the dashboard.  
DIN REAR-MOUNT (Method B)  
Installation using the screw holes on the sides of the unit.  
1
Fastening the unit to the factory radio  
mounting bracket.  
1. Select a position where the screw holes  
of the bracket and the screw holes of the  
main unit become aligned (are fitted), and  
tighten the screws at 2 places on each  
side.  
2
4
Use either truss screws (5 x 5mm) or  
flush surface screws (4 x 5mm),  
depending on the shape of the screw  
holes in the bracket.  
5
3
2. Screw  
2
5
3. Factory radio mounting bracket  
4. Dashboard or Console  
5. Hook (Remove this part)  
Note: The mounting box, outer trim ring,  
and half-sleeve are not used for method B  
installation.  
4
HOW TO REMOVE AND INSTALL THE FRONT PANEL (OPTIONAL)  
1. Press the release button and pull-off the front panel.  
Keep front panel into the case.  
2. To install the front panel, insert the panel into the housing and make sure the panel  
is properly installed, otherwise, abnormalities occurs on the display or some keys  
will not function properly.  
REMOVING THE FRONT PANEL  
Front Panel  
Release Button  
INSTALLING THE FRONT PANEL  
5
WIRING CONNECTION  
FOR 2 X 7W SYSTEM  
CD CHANGER  
CONNECTOR SOCKET  
(FOR CD CHANGER VERSION ONLY)  
MAIN UNIT  
ANTENNA CONNECTOR  
CHOKE BOX  
(GREY)  
RCA CABLE  
Rch RED  
MEMORY  
BACK-UP  
YELLOW  
Lch WHITE  
BLACK  
(FOR RCA LINE OUT VERSION ONLY)  
GROUND (B)  
FUSE  
BLUE  
RED  
POWER  
IGNITION  
ANTENNA  
SWITCH (B+)  
(FOR POWER ANT. VERSION ONLY)  
WHITE  
GREY  
GREY/BLACK  
+
+
Rch  
SPEAKER  
Lch  
SPEAKER  
WHITE/BLACK  
WIRING CONNECTION  
FOR 4 X 7W OR 2 X 25W SYSTEM  
CD CHANGER  
CONNECTOR SOCKET  
(FOR CD CHANGER VERSION ONLY)  
MAIN UNIT  
ANTENNA CONNECTOR  
RED  
(BROWN)  
Rch RED  
FRONT RCA CABLE  
REAR RCA CABLE  
IGNITION  
Lch WHITE  
SWITCH (B+)  
CHOKE BOX  
(GREY)  
MEMORY  
BACK-UP  
YELLOW  
BLACK  
Rch RED  
Lch WHITE  
GROUND (B)  
POWER  
ANTENNA  
BLUE  
(FOR RCA LINE OUT VERSION ONLY)  
2-SPEAKERS SYSTEM  
WHITE  
4-SPEAKERS SYSTEM  
4-SPEAKERS SYSTEM 2-SPEAKERS SYSTEM  
WHITE  
FRONT  
GREY  
GREY  
FRONT  
Lch SPK.  
Rch SPK.  
WHITE/BLACK  
GREY/BLACK  
Lch  
Rch  
SPK.  
SPK.  
GREEN  
REAR  
VIOLET  
REAR  
Lch SPK.  
Rch SPK.  
GREEN/BLACK  
GREEN/BLACK  
VIOLET/BLACK  
VIOLET/BLACK  
Note:  
1. For 2-speakers system, green, violet, white/black and grey/black wire leads are  
unconnected and isolated.  
2. For 2-speakers system, keep the fader control at center position to maintain the  
existing volume level.  
6
OPERATION  
4
17 18  
16  
20  
7
9
15  
1
2
5
19  
3
6
14 12  
8
13  
10  
11  
22 21  
GENERAL OPERATION  
ON/OFF  
Press PWR button (1) to turn on the unit. Press it again to turn it off.  
FACEPLATE RELEASE  
Press REL button (2) to detach the removable faceplate.  
LOUDNESS  
Press LOU/RND button (8) shortly to reinforce the bass output.  
7
SET THE CLOCK  
Press DSP button (9) to change the display to clock display. Press it again to return  
to previous display. In clock display, press and hold the DSP button (9) for several  
seconds until the clock display flashes. Press VOL (5) to change minutes or VOL  
(4) to change hours.  
SELECT MODE  
Press SEL button (3) to change audio mode through volume, bass, treble, balance,  
and fader modes. Use VOL (4) and VOL (5) buttons to adjust the selected  
mode. When mode has not been adjusted for several seconds, display returns to  
normal radio or CD display.  
VOL  
BAS  
TRE  
BAL  
FAD  
(Volume)  
(Bass)  
(Treble)  
(Balance)  
(Fader)  
Volume  
Adjust volume level by using VOL (4) and VOL (5) buttons.  
Note: The unit is initially set to volume mode.  
Bass  
Press SEL button (3) one time. Adjust bass level by using VOL (4) and VOL (5)  
buttons.  
Treble  
Press SEL button (3) two times. Adjust treble level by using VOL (4) and VOL  
(5) buttons.  
Balance  
Press SEL button (3) three times. Adjust sound balance between left and right  
speakers by using VOL (4) and VOL (5) buttons.  
Fader  
Press SEL button (3) four times. Adjust sound balance between front and rear  
speakers by using VOL (4) and VOL (5) buttons.  
MUTE  
Press MUT button (6) to mute down sound. Press it again to release this mode and  
recover previous volume level.  
SELECT MODE  
Press MOD button (7) to change radio or CD mode. During CD operation, press  
BND button (10) to switch to radio mode. During radio operation, when a compact  
disc is inserted in the disc slot (16), press  
start playing.  
button (14) to switch to CD mode and  
EQUALIZATION  
Press EQ button (19) to turn to equalization function and to select desired audio  
mode. There are four kinds of mode as below:  
FLAT  
ROCK  
CLASSIC  
POP  
EQ OFF  
LIQUID CRYSTAL DISPLAY  
The LCD (20) can show the current state of the unit.  
8
FLASHING LED  
If the front panel is not on the main unit, LED (21) will be flashing.  
RESET BUTTON FUNCTION  
RESET button (22) is placed on the housing and must be activated with either a  
ballpoint pen or thin metal object. The RESET button (22) is to be activated for the  
following reasons:  
- Initial installation of the unit when all wiring is completed.  
- All the function buttons do not operate.  
- Error symbol on the display.  
Note: If press RESET button (22), the unit cant work yet, please use a cotton swab  
soaked in isopropyl alcohol to clean the socket on the back of the front panel.  
9
RADIO OPERATION  
BAND  
Press BND button (10) to change bands as below:  
FM  
MW  
LW  
SELECT STATION  
Rotate TUNING knob (11) clockwise or anticlockwise to adjust the frequency  
upward or downward.  
LOCAL/DISTANT  
Press the LOC/RPT button (12) to select between local setting for reception of  
strong station and distant setting for reception of weak stations when tuning.  
MONO/STEREO  
In FM band, press MON/INT button (13) to select mono or stereo reception for  
radio stations. You can sometimes improve reception of distant stations by selecting  
mono operation.  
10  
CD OPERATION  
DISC PLAY  
Gently insert a compact disc with the label side facing up into the disc slot (16).  
The disc is then automatically loaded into the unit and starts playing with the first  
track of the disc. The digital display will indicate the track number and the time of  
the track.  
EJECT  
Press (eject) button (15) to stop CD play and eject CD from slot. Receiver switches  
to radio operation.  
PAUSE CD  
During CD playing, press  
button (14) to temporarily stop playing.  
Press it again to resume playback.  
SKIP TRACKS  
Press TRACK button (17) or TRACK button (18) to choose the following track  
or the previous track. Track numbers show on display.  
FAST FORWARD AND FAST REVERSE  
Hold TRACK button (17) or TRACK button (18) for several seconds to fast  
forward or fast reverse. Releasing the button to stop fast playing.  
REPEAT  
During CD playing, press LOC/RPT button (12) to continuously repeat playing the  
current track. Press it again to release this mode.  
INTRO: PREVIEW ALL TRACKS  
During CD playing, press MON/INT button (13) to play first several seconds of each  
track. Press it again to stop intro and listen to track.  
RANDOM: PLAY ALL TRACKS IN THE RANDOM ORDER  
During CD playing, press and hold LOU/RND button (8) for several seconds to play  
all tracks in the random order. Press it again to cancel the function.  
DISC SELECTION (FOR CDC VERSION ONLY)  
During CDC mode, press CD + button or CD button (19) to select next or previous  
disc.  
11  
SPECIFICATION  
GENERAL  
Power Supply Requirements  
Chassis Dimensions  
Tone Controls  
: DC 12 Volts, Negative Ground  
: 178 (W) x 163 (D) x 50 (H) mm  
- Bass (at 100 Hz)  
- Treble (at 10 KHz)  
Maximum Output Power  
- Version V  
- Low Power Version  
Current Drain  
: +10 dB / 10 dB  
: +10 dB / 10 dB  
: 7W x 4 (ch) or 25W x 2 (ch)  
: 7W x 2 (ch)  
- Version V  
- Low Power Version  
: 5 Ampere (FOR NORMAL POWER)  
: 3 Ampere (FOR LOW POWER)  
CD PLAYER  
Signal to Noise Ratio  
Channel Separation  
Frequency Response  
: More than 60 dB  
: More than 60 dB  
: 20 Hz - 20 KHz  
RADIO  
For 3 Bands  
(Europe)  
FM  
For 2 Bands  
(Europe)  
FM  
For 2 Bands  
(U.S.A.)  
FM  
Frequency Coverage  
IF  
Sensitivity (S/N = 30 dB) : 5 µV  
Stereo Separation  
: 87.5 to 108 MHz 87.5 to 108 MHz 87.5 to 107.9 MHz  
: 10.7 MHz  
10.7 MHz  
5 µV  
> 25 dB  
10.7 MHz  
5 µV  
> 25 dB  
: > 25 dB  
MW  
MW  
AM  
Frequency Coverage  
IF  
Sensitivity (S/N = 20 dB) : 32 dBu  
: 522 to 1620 KHz 522 to 1620 KHz 530 to 1710 KHz  
: 450 KHz  
450 KHz  
32 dBu  
450 KHz  
32 dBu  
LW  
Frequency Coverage  
IF  
: 150 to 280 KHz  
: 450 KHz  
Sensitivity (S/N = 20 dB) : 35 dBu  
12  
TROUBLE SHOOTING  
Before going through the check list, check wiring connection. If any of the problems  
persist after check list has been made, consult your nearest service dealer.  
Symptom  
No power.  
Cause  
Solution  
The car ignition switch is  
not on.  
If the power supply is properly  
connected to the car accessory  
terminal, switch the ignition key  
to ACC.  
The fuse is blown.  
Replace the fuse.  
Disc cannot be  
loaded or ejected. the player.  
Presence of CD disc inside Remove the disc in the player,  
then put a new one.  
Inserting the disc in reverse Insert the compact disc with  
direction. the label facing upward.  
Compact disc is extremely Clean the disc or try to play a  
dirty or defective disc. new one.  
Temperature inside the car Cool off or until the ambient  
is too high.  
temperature return to normal.  
Condensation.  
Leave the player off for an hour  
or so, then try again.  
No sound.  
Volume is in minimum.  
Adjust volume to a desired level.  
Check wiring connection.  
Wiring is not properly  
connected.  
Sound skips.  
The installation angle is  
more than 30 degrees.  
Adjust the installation angle less  
than 30 degrees.  
The disc is extremely dirty  
or defective disc.  
Clean the compact disc, then  
try to play a new one.  
The operation keys The built-in microcomputer Press the RESET button.  
do not work.  
is not operating properly  
due to noise.  
Front panel is not properly fixed  
into its place.  
The radio does not The antenna cable is not  
Insert the antenna cable firmly.  
work. The radio  
station automatic  
selection does not The signals are too weak.  
work.  
connected.  
Select a station manually.  
88-C1133-00  
13  

Pyramid Car Audio PB1281X User Manual
PYLE Audio PLTS72U User Manual
Pelco Car Satellite Radio System C573M D User Manual
Parrot Car Stereo System CK3100 User Manual
Panasonic Palmcorder PV GS32 User Manual
Panasonic HDC SX5PC User Manual
Metra Electronics 99 3410 User Manual
Lochinvar SOLUTION CB 215 User Manual
Kenwood Car Stereo System KDC 3054URY User Manual
JVC KD S17 User Manual