LG Electronics LG Lifes Good Car Video System W2246S User Manual

User’s Guide  
W1946T  
W1946TN  
W2046T  
W2246T  
W2346T  
W1946S  
W1946SN  
W2046S  
W2246S  
W2346S  
Make sure to read the Important Precautions before using the  
product. Keep the User's Guide(CD) in an accessible place for future  
reference.  
See the label attached on the product and give the information to  
your dealer when you ask for service.  
Important Precautions  
On Installation  
Do not allow anything to rest upon or roll over the power cord, and do not place the  
display where the power cord is subject to damage.  
Do not use this display near water such as near a bathtub, washbowl, kitchen sink,  
laundry tub, in a wet basement, or near a swimming pool.  
Displays are provided with ventilation openings in the cabinet to allow the release  
of heat generated during operation. If these openings are blocked, built-up heat  
can cause failures which may result in a fire hazard. Therefore, NEVER:  
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.  
Place the display in a built-in enclosure unless proper ventilation is provided.  
Cover the openings with cloth or other material.  
Place the display near or over a radiator or heat source.  
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,  
mar, or damage the Active Matrix LCD permanently.  
Do not press the LCD screen with your finger for a long time as this may cause  
some afterimages.  
Some dot defects may appear as Red, Green or Blue spots on the screen.  
However, this will have no impact or effect on the display performance.  
If possible, use the recommended resolution to obtain the best image quality for  
your LCD display. If used under any mode except the recommended resolution,  
some scaled or processed images may appear on the screen. However, this is  
characteristic of the fixed-resolution LCD panel.  
Leaving a fixed image on the screen for a long time may cause damage to the  
screen and cause image burn-in. Make sure to use a screen saver on the product.  
Burn-in and related problems are not covered by the warranty on this product.  
Do not shock or scratch the front and sides of the screen with metallic objects.  
Otherwise, it may cause damage to the screen.  
Make sure the panel faces forward and hold it with both hands to move. If you  
drop the product, the damaged product can cause electric shock or fire. Contact  
an authorized the service center for repair.  
Avoid high temperatures and humidity.  
2
Important Precautions  
On Cleaning  
Unplug the display before cleaning the face of the display screen.  
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display  
screen because over-spraying may cause electrical shock.  
When cleaning the product, unplug the power cord and scrub gently with a soft  
cloth to prevent scratching. Do not clean with a wet cloth or spray water or other  
liquids directly onto the product. An electric shock may occur. (Do not use  
chemicals such as benzene, paint thinners or alcohol)  
Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame;  
wipe in one direction only. Too much moisture may cause staining.  
On Repacking  
Do not throw away the carton and packing materials. They make an ideal  
container in which to transport the unit. When shipping the unit to another  
location, repack it in its original material.  
On Disposal (Only , Hg lamp used LCD Monitor)  
The fluorescent lamp used in this product contains a small amount of mercury.  
Do not dispose of this product with general household waste.  
Disposal of this product must be carried out in accordance to the regulations of  
your local authority.  
3
Accessories  
!!! Thank for selecting LGE products !!!  
Please make sure the following items are included with your  
monitor. If any items are missing, contact your dealer.  
Power Cord  
User's Guide/Cards  
15-pin D-Sub Signal Cable  
(To set it up, this signal cable may be  
attached to this product before  
shipping out.)  
DVI-D Signal Cable  
(This feature is not available in all  
countries.)  
(Only W1946T/W1946TN/W2046T/  
W2246T/W2346T  
)
NOTE  
This accessories may look different from those shown here.  
User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferrite  
cores to maintain standard compliance for the product.  
4
Connecting the Display  
Before setting up the monitor, ensure that the power to the monitor, the computer  
system, and other attached devices is turned off.  
Connecting the stand  
1. Place the monitor with its front facing downward on a soft cloth.  
2. Assemble the Stand Body into the  
3. Assemble the Stand Base(Front,  
product in the correct direction as shown in  
the picture. Make sure you push it until you  
hear it “click”.  
Rear) into the Stand Body in the  
correct direction.  
Hinge Body  
Stand Body  
Stand Body  
Stand Base  
4. Tie down the base lock to perpendicularity direction.  
5. Once assembled take the monitor up carefully and face the front side  
.
Important  
This illustration depicts the general model of connection. Your monitor may differ from  
the items shown in the picture.  
Do not carry the product upside down holding only the stand base. The product may  
fall and get damaged or injure your foot.  
5
Connecting the Display  
Disassembling the stand  
2. Place the monitor face Down on the  
1. Put a cushion or soft cloth on aflat  
cushion or soft cloth.  
surface.  
3. Change your lock on the product as it follows and turn it in the arrow direction.  
If you can't release the stand base even the locking knob is at a release  
position, Please push the indicated knob down and retry it.  
6
Connecting the Display  
4. Pull out the Stand to remove.  
5. Pushing the PUSH button, Take the stand body from hinge body.  
Good Position  
Bad Position  
Warning:  
You can hurt your finger.  
7
Connecting the Display  
Before setting up the monitor, ensure that the power to the monitor,  
the computer system, and other attached devices is turned off.  
Positioning your display  
-After installation, adjust the angle as shown below.  
1. Adjust the position of the panel in various ways for maximum comfort.  
Tilt Range : -5˚ to 15˚  
Do not touch or press the screen when  
adjusting the angle of the monitor.  
When adjusting the angle of the screen, do  
not put your finger(s) in between the head of  
the monitor and the stand body. You can  
hurt your finger(s).  
ERGONOMIC  
It is recommended that in order to maintain an ergonomic and comfortable viewing position,  
the forward tilt angle of the monitor should not exceed 5 degrees.  
8
Connecting the Display  
W1946T/W1946TN/W2046T/W2246T/W2346T  
Connecting with the PC  
1. Before setting up the monitor, ensure that the power to the monitor, the computer  
2. sCyosntenmec, tasnidgnoathleinrpautttaccahbedledeviceasnids ptuorwneedr ocoff.rd  
in order, then tighten the screw  
1
2
of the signal cable.  
A
Connect DVI-D(Digital signal) Cable  
B
Connect D-sub(Analog signal) Cable  
NOTE  
This is a simplified representation of the rear view.  
This rear view represents a general model; your display may differ from the view as shown.  
When using a D-Sub signal input cable connector  
for Macintosh  
Mac adapter : For Apple Macintosh use, a  
separate plug adapter is needed to change the  
15 pin high density (3 row) D-sub VGA  
connector on the supplied cable to a 15 pin 2  
row connector.  
Varies according to model.  
Wall-outlet type  
DVI-D (This feature is not available in all countries.)  
B
A
PC  
PC  
3. Press the power button on the front panel to turn the power on. When monitor power is  
turned on, the 'Self Image Setting Function' is executed automatically.  
(Only Analog Mode)  
Power Button  
NOTE  
‘ Self Image Setting Function’? This function provides the user with optimal display  
settings.When the user connects the monitor for the first time, this function automatically adjusts  
the display to optimal settings for individual input signals.  
‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters, screen  
flicker or tilted screen while using the device or after changing screen resolution, press the  
AUTO function button to improve resolution.  
9
Connecting the Display  
W1946S/W1946SN/W2046S/W2246S/W2346S  
Connecting with the PC  
1. Before setting up the monitor, ensure that the power to the monitor, the computer  
2. sCyosntenmec, tasnidgnoathleinrpautttaccahbedledeviceasnids ptuorwneedr ocoff.rd  
in order, then tighten the screw  
1
2
of the signal cable.  
A
Connect D-sub(Analog signal) Cable  
NOTE  
This is a simplified representation of the rear view.  
This rear view represents a general model; your display may differ from the view as shown.  
When using a D-Sub signal input cable connector for  
Macintosh  
Mac adapter :For Apple Macintosh use, a  
separate plug adapter is needed to change the  
15 pin high density (3 row) D-sub VGA  
connector on the supplied cable to a 15 pin 2  
row connector.  
Varies according to model.  
Wall-outlet type  
A
PC  
3. Press the power button on the front panel to turn the power on. When monitor power is  
turned on, the 'Self Image Setting Function' is executed automatically.  
Power Button  
NOTE  
‘ Self Image Setting Function’? This function provides the user with optimal display  
settings.When the user connects the monitor for the first time, this function automatically adjusts  
the display to optimal settings for individual input signals.  
‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters, screen  
flicker or tilted screen while using the device or after changing screen resolution, press the  
AUTO function button to improve resolution.  
10  
Connecting the Display  
Using the cable holder (This feature is not available in all models.)  
W1946T/W1946TN/W2046T  
3
Cable holder  
1
2
W1946S/W1946SN/W2046S  
3
Cable holder  
1
2
11  
Control Panel Functions  
Front Panel Controls  
W1946T/W1946TN/W2046T/W2246T/W2346T  
W1946S/W1946SN/W2046S/W2246S/W2346S  
MENU Button  
OSD LOCKED/UNLOCKED  
This function allows you to lock the current control  
settings, so that they cannot be inadvertently changed.  
Press and hold the MENU button for several seconds.  
The message "OSD LOCKED" should appear.  
You can unlock the OSD controls at any time by pushing  
the MENU button for several seconds. The message  
"OSD UNLOCKED" should appear.  
12  
Control Panel Functions  
MODE Button  
Use this button to enter F-ENGINE, ORIGINAL  
RATIO menus.  
For more information, refer to page 20.  
AUTO Button  
AUTO IMAGE ADJUSTMENT  
When adjusting your display settings, always press the  
AUTO button before entering the On Screen  
Display(OSD). (Only Analog Mode)  
This will automatically adjust your display image to the  
ideal settings for the current screen resolution size  
(display mode).  
The best display mode is  
W1946S/W1946SN/W1946T/W1946TN : 1360 x 768  
W2046S/W2046T : 1600 x 900  
W2246S/W2346S/W2246T/W2346T : 1920 x1080  
When two input signals are connected, you can select the  
input signal (D-SUB/DVI) you want. When only one signal  
is connected, it is automatically detected. The default  
setting is D-Sub.  
INPUT Button  
(SOURCE Hot key)  
(Only W1946T/W1946TN/W2046T/W2246T/W2346T )  
EXIT Button  
Exit the OSD(On Screen Display).  
Use this button to turn the display on or off.  
Power Button &  
Power Indicator  
The power indicator stays white if the display is running  
properly (On Mode). If the display is in Sleep Mode  
(Energy Saving), the power indicator is blinking white.  
13  
On Screen Display (OSD) Control Adjustment  
Screen Adjustment  
Making adjustments to the image size, position and operating  
parameters of the display is quick and easy with the On Screen  
Display Control system.  
A short example is given below to familiarize you with the use of the  
controls. The following section is an outline of the available  
adjustments and selections you can make using the OSD.  
To make adjustments in the On Screen Display, follow these steps:  
Press the discretionary Button, then the main menu of the OSD appears.  
1
To access a control, use the corresponding Buttons.  
2
Use the  
Use the  
/
Buttons to adjust the image to the desired level.  
3
4
Button to select other sub-menu items.  
Press the EXIT Button to exit from the OSD.  
14  
On Screen Display(OSD) Selection and Adjustment  
The following table indicates all the On Screen Display control, adjustment,  
and setting menus.  
DSUB : D-SUB(Analog signal) input  
DVI-D : DVI-D(Digital signal) input  
Main menu  
PICTURE  
Sub-menu  
BRIGHTNESS  
Supported input  
Description  
To adjust the brightness, contrast  
and sharpness of the screen  
DSUB  
DVI-D  
CONTRAST  
SHARPNESS  
To customize the color of the  
screen  
COLOR TEMP  
(PRESET / USER)  
DSUB  
DVI-D  
COLOR  
GAMMA  
HORIZONTAL  
VERTICAL  
To adjust the position of the  
screen  
DISPLAY  
DSUB  
DSUB  
CLOCK  
PHASE  
To improve the clarity and  
stability of the screen  
DSUB  
DVI-D  
LANGUAGE  
OTHERS  
To customize the screen status  
for a user's operating  
environment  
POWER INDICATOR  
DSUB  
WHITE BALANCE  
FACTORY RESET  
DSUB  
DVI-D  
DSUB  
DVI-D  
NORMAL  
MOVIE  
F-ENGINE  
To select or customize desired  
image settings  
INTERNET  
DEMO  
DSUB  
DVI-D  
WIDE  
ORIGINAL  
ORIGINAL  
RATIO  
To adjust the image size  
NOTE  
The order of icons may differ depending on the model (15~22).  
15  
On Screen Display(OSD) Selection and Adjustment  
You were introduced to the procedure of selecting and adjusting an item  
using the OSD system. Listed below are the icons, icon names, and icon  
descriptions of the all items shown on the Menu.  
Press the MENU Button, then the main menu of the OSD appears.  
Menu Name  
Sub-  
menus  
Icons  
Button  
Tip  
Exit  
Adjust (Decrease/Increase)  
Select another sub-menu  
Restart to select sub-menu  
NOTE  
OSD (On Screen Display) menu languages on the monitor may differ from the manual.  
16  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
To adjust the brightness of the screen.  
To adjust the contrast of the screen.  
To adjust the clearness of the screen.  
BRIGHTNESS  
CONTRAST  
SHARPNESS  
Exit : Exit  
: Decrease  
: Increase  
: Select another sub-menu  
: Restart to select sub-menu  
COLOR TEMP  
Select the screen color.  
• sRGB: Set the screen color to fit the  
sRGB standard color  
PRESET  
specification.  
• 6500K-7500K: Red screen color.  
• 8500K-9300K: Blue screen color.  
Exit : Exit  
USER  
RED  
: Decrease  
Set your own red color levels.  
: Increase  
GREEN  
Set your own green color levels.  
: Select another sub-menu  
: Restart to select sub-menu  
BLUE  
Set your own blue color levels.  
GAMMA  
Set your own gamma value. : 0 / 1 / 2  
On the monitor, high gamma values  
display whitish images and low  
gamma values display blackish  
images.  
17  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
W1946T/W1946TN/W2046T/W2246T/W2346T  
HORIZONTAL  
To move image left and right.  
To move image up and down.  
VERTICAL  
CLOCK  
To minimize any vertical bars or  
stripes visible on the screen  
background.  
The horizontal screen size will also  
change.  
W1946S/W1946SN/W2046S/W2246S/W2346S  
To adjust the focus of the display.  
This item allows you to remove any  
horizontal noise and clear or sharpen  
the image of characters.  
PHASE  
Exit : Exit  
: Decrease  
: Increase  
: Select another sub-menu  
: Restart to select sub-menu  
18  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
To choose the language in which the  
control names are displayed.  
LANGUAGE  
Use this function to set the power  
indicator on the front side of the monitor  
to ON or OFF.  
POWER  
INDICATOR  
If you set OFF, it will go off.  
If you set ON at any time, the power  
indicator will automatically be turned on.  
Exit : Exit  
: Decrease  
WHITE  
BALANCE  
If the output of the video card is  
different the required specifications,  
the color level may deteriorate due  
to video signal distortion. Using this  
function, the signal level is adjusted  
to fit into the standard output level of  
the video card in order to provide the  
optimal image.  
: Increase  
: Select another sub-menu  
: Restart to select sub-menu  
Activate this function when white  
and black colors are present in the  
screen.  
Restore all factory default settings except  
FACTORY  
RESET  
"LANGUAGE."  
Press the  
,
buttons to reset  
immediately.  
NOTE  
If this does not improve the screen image, restore the factory default settings. If necessary, execute the  
WHITE BALANCE function again. This function will be enabled only when the input signal is an analog  
signal.  
19  
On Screen Display(OSD) Selection and Adjustment  
You were introduced to the procedure of selecting and adjusting an item  
using the OSD system. Listed below are the icons, icon names, and icon  
descriptions of the all items shown on the Menu.  
Press the MODE Button, then the main menu of the OSD appears.  
Menu Name  
Sub-  
menus  
Icons  
Button  
Tip  
Exit  
Move  
Select another sub-menu  
NOTE  
OSD (On Screen Display) menu languages on the monitor may differ from the manual.  
20  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
NORMAL  
Select this when you want to use the product  
in the most general using environment.  
MOVIE  
Select this when you are watching a video or  
movie.  
INTERNET  
Select this when you are working on the  
document (Word etc.)  
DEMO  
This is used for advertising in the store. The  
screen will be divided to show the standard  
mode on the left and video mode on the right so  
that the consumers can check the difference  
after applying the video mode.  
Exit : Exit  
: Move  
: Select another sub-menu  
,
21  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
WIDE  
Switch to full screen mode according to  
input image signal.  
ORIGINAL Change the input image signal ratio to  
original.  
* This function works only if input  
resolution is lower than monitor ratio  
(16:9).  
Exit : Exit  
: Move  
: Select another sub-menu  
,
22  
Troubleshooting  
Check the following before calling for service.  
No image appears  
G Is the power cord of the  
Check and see if the power cord is connected  
properly to the power outlet.  
display connected?  
G Is the power indicator  
Press the Power button.  
light on?  
G Is the power indicator  
If the display is in power saving mode, try moving  
the mouse or pressing any key on the keyboard to  
bring up the screen.  
flickering?  
• Try to turn on the PC  
.
G Do you see an "OUT OF  
RANGE" message on  
the screen?  
This message appears when the signal from the  
PC (video card) is out of horizontal or vertical  
frequency range of the display. See the  
'Specifications' section of this manual and  
configure your display again.  
This message appears when the signal cable  
between your PC and your display is not  
connected. Check the signal cable and try again.  
G Do you see a "CHECK  
SIGNAL CABLE"  
message on the  
screen?  
Do you see a "OSD LOCKED" message on the screen?  
G
Do you see “OSD  
LOCKED” when you  
push MENU button?  
• You can secure the current control settings,  
so that they cannot be inadvertently changed.  
You can unlock the OSD controls at any time  
by pushing the MENU button for several  
seconds: the message  
“OSD UNLOCKED” will appear.  
23  
Troubleshooting  
Display image is incorrect  
G Display Position is  
Press the AUTO button to automatically adjust  
your display image to the ideal setting.  
If the results are unsatisfactory, adjust the image  
position using the H position and V position icon  
in the on screen display.  
incorrect.  
Press the AUTO button to automatically adjust  
your display image to the ideal setting.  
If the results are unsatisfactory, decrease the  
vertical bars or stripes using the CLOCK icon in  
the on screen display.  
G On the screen  
background, vertical  
bars or stripes are  
visible.  
Press the AUTO button to automatically adjust  
your display image to the ideal setting.  
If the results are unsatisfactory, decrease the  
horizontal bars using the PHASE icon in the on  
screen display.  
Check Control Panel --> Display --> Settings  
and adjust the display to the recommended  
resolution or adjust the display image to the ideal  
setting. Set the color setting higher than 24 bits  
(true color).  
G Any horizontal noise  
appearing in any  
image or characters  
are not clearly  
portrayed.  
IMPORTANT  
Check Control Panel --> Display --> Settings and see if the frequency or the  
resolution were changed. If yes, readjust the video card to the recommend  
resolution.  
If the recommended resolution (optimal resolution) is not selected, letters may be  
blurred and the screen may be dimmed, truncated or biased. Make sure to select  
the recommend resolution.  
The setting method can differ by computer and O/S (Operation System),  
and resolution mentioned above may not be supported by the video card  
performance. In this case, please ask to the computer or the video card  
manufacturer.  
24  
Troubleshooting  
Display image is incorrect  
G The screen color is  
Check if the signal cable is properly connected  
and use a screwdriver to fasten if necessary.  
Make sure the video card is properly inserted in  
the slot.  
Set the color setting higher than 24 bits (true color)  
at Control Panel - Settings.  
mono or abnormal.  
G The screen blinks.  
Check if the screen is set to interlace mode and if  
yes, change it to the recommend resolution.  
Do you see an "Unrecognized monitor, Plug&Play (VESA  
DDC) monitor found" message?  
G
Have you installed the  
display driver?  
Be sure to install the display driver from the display  
driver CD (or diskette) that comes with your  
display. Or, you can also download the driver from  
Make sure to check if the video card supports  
Plug&Play function.  
25  
Specifications  
W1946T/W1946TN  
47.0 cm (18.5 inch) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Display  
Visible diagonal size : 47.0 cm  
0.300 x 0.300 mm (Pixel pitch)  
Horizontal Freq.  
Vertical Freq.  
Input Form  
30 kHz to 61 kHz (Automatic)  
56 Hz to 75 Hz (Automatic)  
Separate Sync.  
Sync Input  
Video Input  
SOG (Sync On Green), Digital  
Signal Input  
Input Form  
15 pin D-Sub Connector  
DVI-D Connector (Digital)  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Max  
Recommend  
VESA 1360 x 768 @60 Hz  
VESA 1360 x 768 @60 Hz  
Resolution  
Plug&Play  
DDC 2B(Digital),DDC2AB(Anlaog)  
:
22 W(Typ.)  
0.5 W  
0.5 W  
On Mode  
Power  
Consumption  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
& Weight  
Width 44.26 cm ( 17.42 inch)  
Height 35.62 cm ( 14.02 inch)  
Depth 16.99 cm ( 6.68 inch)  
Width 44.26 cm ( 17.42 inch)  
Height 26.67 cm (10.50 inch)  
Depth 6.04 cm ( 2.37 inch)  
Weight(excl. packing)  
3.0 kg (6.66 lb)  
Tilt : -5˚ to 15˚  
Range  
AC 100-240 V~ 50 / 60 Hz 0.8 A  
Power Input  
Operating Conditions  
Environment  
al Conditions  
Temperature  
Humidity  
10 ˚C to 35 ˚C  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20 ˚C to 60 ˚C  
5 % to 90 % non-Condensing  
Attached ( ), Detached ( O )  
Wall-outlet type  
Stand Base  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
26  
Specifications  
W1946S/W1946SN  
47.0 cm (18.5 inch) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Display  
Visible diagonal size : 47.0 cm  
0.300 x 0.300 mm (Pixel pitch)  
Horizontal Freq.  
Vertical Freq.  
Input Form  
30 kHz to 61 kHz (Automatic)  
56 Hz to 75 Hz (Automatic)  
Separate Sync.  
Sync Input  
Video Input  
SOG (Sync On Green)  
Signal Input  
Input Form  
15 pin D-Sub Connector  
RGB Analog (0.7 Vp-p/ 75 ohm)  
Max  
Recommend  
VESA 1360 x 768 @60 Hz  
VESA 1360 x 768 @60 Hz  
Resolution  
Plug&Play  
DDC 2AB  
:
22 W(Typ.)  
0.5 W  
0.5 W  
On Mode  
Power  
Consumption  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
& Weight  
Width 44.26 cm (17.42 inch)  
Height 35.62 cm (14.02 inch)  
Depth 16.99 cm ( 6.68 inch)  
Width 44.26 cm (17.42 inch)  
Height 26.67 cm (10.50 inch)  
Depth 6.04 cm ( 2.37 inch)  
Weight(excl. packing)  
3.0 kg (6.66 lb)  
Tilt : -5˚ to 15˚  
Range  
AC 100-240 V~ 50 / 60 Hz 0.8 A  
Power Input  
Operating Conditions  
Environment  
al Conditions  
Temperature  
Humidity  
10 ˚C to 35 ˚C  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20 ˚C to 60 ˚C  
5 % to 90 % non-Condensing  
Attached ( ), Detached ( O )  
Wall-outlet type  
Stand Base  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
27  
Specifications  
W2046T  
50.8 cm (20.0 inch) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Display  
Visible diagonal size : 50.8 cm  
0.2766 x 0.2766 mm (Pixel pitch)  
Horizontal Freq.  
Vertical Freq.  
Input Form  
30 kHz to 83 kHz (Automatic)  
56 Hz to 75 Hz (Automatic)  
Separate Sync.  
Sync Input  
Video Input  
SOG (Sync On Green), Digital  
Signal Input  
Input Form  
15 pin D-Sub Connector  
DVI-D Connector (Digital)  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Max  
Recommend  
VESA 1600 x 900 @ 60 Hz  
VESA 1600 x 900 @ 60 Hz  
Resolution  
Plug&Play  
DDC 2B(Digital),DDC2AB(Anlaog)  
:
24 W(Typ.)  
0.5 W  
0.5 W  
On Mode  
Power  
Consumption  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
& Weight  
Width 47.58 cm (18.73 inch)  
Height 37.64 cm (14.81 inch)  
Depth 16.99 cm ( 6.68 inch)  
Width 47.58 cm (18.73 inch)  
Height 30.35 cm ( 11.94 inch)  
Depth 6.08 cm ( 2.39 inch)  
Weight(excl. packing)  
3.2 kg (7.11 lb)  
Tilt : -5˚ to 15˚  
Range  
AC 100-240 V~ 50 / 60 Hz 1.0 A  
Power Input  
Operating Conditions  
Environment  
al Conditions  
Temperature  
Humidity  
10 ˚C to 35 ˚C  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20 ˚C to 60 ˚C  
5 % to 90 % non-Condensing  
Attached ( ), Detached ( O )  
Wall-outlet type  
Stand Base  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
28  
Specifications  
W2046S  
50.8 cm (20.0 inch) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Display  
Visible diagonal size : 50.8 cm  
0.2766 x 0.2766 mm (Pixel pitch)  
Horizontal Freq.  
Vertical Freq.  
Input Form  
30 kHz to 83 kHz (Automatic)  
56 Hz to 75 Hz (Automatic)  
Separate Sync.  
Sync Input  
Video Input  
SOG (Sync On Green)  
Signal Input  
Input Form  
15 pin D-Sub Connector  
RGB Analog (0.7 Vp-p/ 75 ohm)  
Max  
Recommend  
VESA 1600 x 900 @ 60 Hz  
VESA 1600 x 900 @ 60 Hz  
Resolution  
Plug&Play  
DDC 2AB  
:
24 W(Typ.)  
0.5 W  
0.5 W  
On Mode  
Power  
Consumption  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
& Weight  
Width 47.58 cm ( 18.73 inch)  
Height 37.64 cm ( 14.81 inch)  
Depth 16.99 cm ( 6.68 inch)  
Width 47.58 cm ( 18.73 inch)  
Height 30.35 cm ( 11.94 inch)  
Depth 6.08 cm ( 2.39 inch)  
Weight(excl. packing)  
3.2 kg (7.11 lb)  
Tilt : -5˚ to 15˚  
Range  
AC 100-240 V~ 50 / 60 Hz 1.0 A  
Power Input  
Operating Conditions  
Environment  
al Conditions  
Temperature  
Humidity  
10 ˚C to 35 ˚C  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20 ˚C to 60 ˚C  
5 % to 90 % non-Condensing  
Attached ( ), Detached ( O )  
Wall-outlet type  
Stand Base  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
29  
Specifications  
W2246T  
54.6 cm (21.5 inch) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Display  
Visible diagonal size : 54.6 cm  
0.248 x 0.248 mm (Pixel pitch)  
Horizontal Freq.  
Vertical Freq.  
Input Form  
30 kHz to 83 kHz (Automatic)  
56 Hz to 75 Hz (Automatic)  
Separate Sync.  
Sync Input  
Video Input  
SOG (Sync On Green), Digital  
Signal Input  
Input Form  
15 pin D-Sub Connector  
DVI-D Connector (Digital)  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Max  
Recommend  
VESA 1920 x 1080 @60 Hz  
VESA 1920 x 1080 @60 Hz  
Resolution  
Plug&Play  
DDC 2B(Digital),DDC2AB(Anlaog)  
:
24 W(Typ.)  
0.5 W  
0.5 W  
On Mode  
Power  
Consumption  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
& Weight  
Width 50.92 cm ( 20.04 inch)  
Height 39.69 cm ( 15.62 inch)  
Depth 21.00 cm ( 8.26 inch)  
Width 50.92 cm ( 20.04 inch)  
Height 30.42 cm ( 11.97 inch)  
Depth 5.98 cm ( 2.35 inch)  
Weight(excl. packing)  
3.5 kg (7.77 lb)  
Tilt : -5˚ to 15˚  
Range  
AC 100-240 V~ 50 / 60 Hz 1.0 A  
Power Input  
Operating Conditions  
Environment  
al Conditions  
Temperature  
Humidity  
10 ˚C to 35 ˚C  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20 ˚C to 60 ˚C  
5 % to 90 % non-Condensing  
Attached ( ), Detached ( O )  
Wall-outlet type  
Stand Base  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
30  
Specifications  
W2246S  
54.6 cm (21.5 inch) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Display  
Visible diagonal size : 54.6 cm  
0.248 x 0.248 mm (Pixel pitch)  
Horizontal Freq.  
Vertical Freq.  
Input Form  
30 kHz to 83 kHz (Automatic)  
56 Hz to 75 Hz (Automatic)  
Separate Sync.  
Sync Input  
Video Input  
SOG (Sync On Green)  
Signal Input  
Input Form  
15 pin D-Sub Connector  
RGB Analog (0.7 Vp-p/ 75 ohm)  
Max  
Recommend  
VESA 1920 x 1080 @60 Hz  
VESA 1920 x 1080 @60 Hz  
Resolution  
Plug&Play  
DDC 2AB  
:
24 W(Typ.)  
0.5 W  
0.5 W  
On Mode  
Power  
Consumption  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
& Weight  
Width 50.92 cm ( 20.04 inch)  
Height 39.69 cm ( 15.62 inch)  
Depth 21.00 cm ( 8.26 inch)  
Width 50.92 cm ( 20.04 inch)  
Height 30.42 cm ( 11.97 inch)  
Depth 5.98 cm ( 2.35 inch)  
Weight(excl. packing)  
3.5 kg (7.77 lb)  
Tilt : -5˚ to 15˚  
Range  
AC 100-240 V~ 50 / 60 Hz 1.0 A  
Power Input  
Operating Conditions  
Environment  
al Conditions  
Temperature  
Humidity  
10 ˚C to 35 ˚C  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20 ˚C to 60 ˚C  
5 % to 90 % non-Condensing  
Attached ( ), Detached ( O )  
Wall-outlet type  
Stand Base  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
31  
Specifications  
W2346T  
58.4 cm (23 inch) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Display  
Visible diagonal size : 58.4 cm  
0.266 x 0.266 mm (Pixel pitch)  
Horizontal Freq.  
Vertical Freq.  
Input Form  
30 kHz to 83 kHz (Automatic)  
56 Hz to 75 Hz (Automatic)  
Separate Sync.  
Sync Input  
Video Input  
SOG (Sync On Green), Digital  
Signal Input  
Input Form  
15 pin D-Sub Connector  
DVI-D Connector (Digital)  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Max  
Recommend  
VESA 1920 x 1080 @60 Hz  
VESA 1920 x 1080 @60 Hz  
Resolution  
Plug&Play  
DDC 2B(Digital),DDC2AB(Anlaog)  
:
27 W(Typ.)  
0.5 W  
0.5 W  
On Mode  
Power  
Consumption  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
& Weight  
Width 54.25 cm ( 21.35 inch)  
Height 41.66 cm ( 16.40 inch)  
Depth 21.00 cm ( 8.26 inch)  
Width 54.25 cm ( 21.35 inch)  
Height 32.30 cm ( 12.71 inch)  
Depth 6.05 cm ( 2.38 inch)  
Weight(excl. packing)  
4.2 kg (9.33 lb)  
Tilt : -5˚ to 15˚  
Range  
AC 100-240 V~ 50 / 60 Hz 1.0 A  
Power Input  
Operating Conditions  
Environment  
al Conditions  
Temperature  
Humidity  
10 ˚C to 35 ˚C  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20 ˚C to 60 ˚C  
5 % to 90 % non-Condensing  
Attached ( ), Detached ( O )  
Wall-outlet type  
Stand Base  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
32  
Specifications  
W2346S  
58.4 cm (23 inch) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Display  
Visible diagonal size : 58.4 cm  
0.266 x 0.266 mm (Pixel pitch)  
Horizontal Freq.  
Vertical Freq.  
Input Form  
30 kHz to 83 kHz (Automatic)  
56 Hz to 75 Hz (Automatic)  
Separate Sync.  
Sync Input  
Video Input  
SOG (Sync On Green)  
Signal Input  
Input Form  
15 pin D-Sub Connector  
RGB Analog (0.7 Vp-p/ 75 ohm)  
Max  
Recommend  
VESA 1920 x 1080 @60 Hz  
VESA 1920 x 1080 @60 Hz  
Resolution  
Plug&Play  
DDC 2AB  
:
27 W(Typ.)  
0.5 W  
0.5 W  
On Mode  
Power  
Consumption  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
& Weight  
Width 54.25 cm (21.35 inch)  
Height 41.66 cm (16.40 inch)  
Depth 21.00 cm ( 8.26 inch)  
Width 54.25 cm ( 21.35 inch)  
Height 32.30 cm ( 12.71 inch)  
Depth 6.05 cm ( 2.38 inch)  
Weight(excl. packing)  
4.2 kg (9.33 lb)  
Tilt : -5˚ to 15˚  
Range  
AC 100-240 V~ 50 / 60 Hz 1.0 A  
Power Input  
Operating Conditions  
Environment  
al Conditions  
Temperature  
Humidity  
10 ˚C to 35 ˚C  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20 ˚C to 60 ˚C  
5 % to 90 % non-Condensing  
Attached ( ), Detached ( O )  
Wall-outlet type  
Stand Base  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
33  
Specifications  
Preset Modes (Resolution)  
W1946T/W1946TN/W1946S/W1946SN  
Display Modes (Resolution) Horizontal Freq. (kHz)  
Vertical Freq. (Hz)  
1
2
31.468  
31.469  
37.500  
37.879  
46.875  
49.725  
48.363  
60.123  
47.712  
720 x 400  
640 x 480  
640 x 480  
800 x 600  
800 x 600  
832 x 624  
1024 x 768  
1024 x 768  
1360 x 768  
70  
60  
75  
60  
75  
75  
60  
75  
60  
3
4
5
6
7
8
*9  
*Recommend Mode  
W2046T/W2046S  
Display Modes (Resolution)  
Horizontal Freq. (kHz)  
Vertical Freq. (Hz)  
1
2
31.468  
31.469  
37.500  
37.879  
46.875  
48.363  
60.123  
67.500  
60.000  
720 x 400  
640 x 480  
640 x 480  
800 x 600  
800 x 600  
1024 x 768  
1024 x 768  
1152 x 864  
1600 x 900  
70  
60  
75  
60  
75  
60  
75  
75  
60  
3
4
5
6
7
8
*9  
*Recommend Mode  
34  
Specifications  
W2246T/W2346T/W2246S/W2346S  
Display Modes (Resolution)  
Horizontal Freq. (kHz)  
Vertical Freq. (Hz)  
1
2
31.468  
31.469  
37.500  
37.879  
46.875  
48.363  
60.123  
67.500  
63.981  
79.976  
65.290  
67.500  
720 x 400  
640 x 480  
70  
60  
75  
60  
75  
60  
75  
75  
60  
75  
60  
60  
3
640 x 480  
4
800 x 600  
800 x 600  
5
6
1024 x 768  
1024 x 768  
1152 x 864  
1280 x 1024  
1280 x 1024  
1680 x 1050  
1920 x 1080  
7
8
9
10  
11  
*12  
*Recommend Mode  
Indicator  
LED Color  
MODE  
White  
White Blinking  
Off  
On Mode  
Sleep Mode  
Off Mode  
35  
Installing the Wall mount plate  
This monitor satisfies the specifications of the Wall mount plate or  
the interchange device.  
1. Place the monitor with its front facing downward on a soft cloth.  
2. Separate the stand by pushing the PUSH button.  
Good Position  
Bad Position  
Warning:  
You can hurt your finger.  
3. Install the Wall mount plate.  
Wall mount plate(Separate purchase)  
This is stand-type or wall mount type and is  
connectable with Wall mount plate.  
Please refer to the installation guide for more details,  
which is provided when Wall mount plate is purchased.  
- Be sure to use screws and a wall mount that  
meet VESA standards.  
- Using screws longer than those  
recommended might damage the product.  
- Using screws that do not meet VESA  
standards might either damage the product  
or result in it coming away from the wall.We  
will not be held responsible for any damage  
resulting from failure to follow these  
instructions.  
<Please use VESA standard as a recommendation.>  
Mounting crew:  
Interface pad thickness: 2.6mm  
Screw :  
4mm x pitch 0.7mm x length 10mm  
Kensington Security Slot  
Connected to a locking cable that can be  
purchased separately at most computer stores.  
36  
Digitally yours  

Pelco Camera Lens 13FF6D 4PAK User Manual
Panasonic Camcorder DMC SZ9 User Manual
Optimus CD 8400 User Manual
Olympus WCON 07C User Manual
Olympus TCON 14D User Manual
Maxxsonics Car Amplifier P1 6002 User Manual
Listen Technologies DCN LBB 3504 User Manual
Life is good LG Blu ray Disc Player with Built In Wi Fi BP330 User Manual
Kompernass KH498 08 V1 User Manual
JVC KS FX811 User Manual