User’s Guide
W1946T
W1946TN
W2046T
W2246T
W2346T
W1946S
W1946SN
W2046S
W2246S
W2346S
Make sure to read the Important Precautions before using the
product. Keep the User's Guide(CD) in an accessible place for future
reference.
See the label attached on the product and give the information to
your dealer when you ask for service.
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place the
display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,
mar, or damage the Active Matrix LCD permanently.
Do not press the LCD screen with your finger for a long time as this may cause
some afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.
If possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
Leaving a fixed image on the screen for a long time may cause damage to the
screen and cause image burn-in. Make sure to use a screen saver on the product.
Burn-in and related problems are not covered by the warranty on this product.
Do not shock or scratch the front and sides of the screen with metallic objects.
Otherwise, it may cause damage to the screen.
Make sure the panel faces forward and hold it with both hands to move. If you
drop the product, the damaged product can cause electric shock or fire. Contact
an authorized the service center for repair.
Avoid high temperatures and humidity.
2
Important Precautions
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
When cleaning the product, unplug the power cord and scrub gently with a soft
cloth to prevent scratching. Do not clean with a wet cloth or spray water or other
liquids directly onto the product. An electric shock may occur. (Do not use
chemicals such as benzene, paint thinners or alcohol)
Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame;
wipe in one direction only. Too much moisture may cause staining.
On Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
On Disposal (Only , Hg lamp used LCD Monitor)
The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of
your local authority.
3
Accessories
!!! Thank for selecting LGE products !!!
Please make sure the following items are included with your
monitor. If any items are missing, contact your dealer.
Power Cord
User's Guide/Cards
15-pin D-Sub Signal Cable
(To set it up, this signal cable may be
attached to this product before
shipping out.)
DVI-D Signal Cable
(This feature is not available in all
countries.)
(Only W1946T/W1946TN/W2046T/
W2246T/W2346T
)
NOTE
This accessories may look different from those shown here.
User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferrite
cores to maintain standard compliance for the product.
4
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Connecting the stand
1. Place the monitor with its front facing downward on a soft cloth.
2. Assemble the Stand Body into the
3. Assemble the Stand Base(Front,
product in the correct direction as shown in
the picture. Make sure you push it until you
hear it “click”.
Rear) into the Stand Body in the
correct direction.
Hinge Body
Stand Body
Stand Body
Stand Base
4. Tie down the base lock to perpendicularity direction.
5. Once assembled take the monitor up carefully and face the front side
.
Important
This illustration depicts the general model of connection. Your monitor may differ from
the items shown in the picture.
Do not carry the product upside down holding only the stand base. The product may
fall and get damaged or injure your foot.
5
Connecting the Display
Disassembling the stand
2. Place the monitor face Down on the
1. Put a cushion or soft cloth on aflat
cushion or soft cloth.
surface.
3. Change your lock on the product as it follows and turn it in the arrow direction.
If you can't release the stand base even the locking knob is at a release
position, Please push the indicated knob down and retry it.
6
Connecting the Display
4. Pull out the Stand to remove.
5. Pushing the PUSH button, Take the stand body from hinge body.
Good Position
Bad Position
Warning:
You can hurt your finger.
7
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor,
the computer system, and other attached devices is turned off.
Positioning your display
-After installation, adjust the angle as shown below.
1. Adjust the position of the panel in various ways for maximum comfort.
Tilt Range : -5˚ to 15˚
Do not touch or press the screen when
adjusting the angle of the monitor.
When adjusting the angle of the screen, do
not put your finger(s) in between the head of
the monitor and the stand body. You can
hurt your finger(s).
ERGONOMIC
It is recommended that in order to maintain an ergonomic and comfortable viewing position,
the forward tilt angle of the monitor should not exceed 5 degrees.
8
Connecting the Display
W1946T/W1946TN/W2046T/W2246T/W2346T
Connecting with the PC
1. Before setting up the monitor, ensure that the power to the monitor, the computer
2. sCyosntenmec, tasnidgnoathleinrpautttaccahbedledeviceasnids ptuorwneedr ocoff.rd
in order, then tighten the screw
1
2
of the signal cable.
A
Connect DVI-D(Digital signal) Cable
B
Connect D-sub(Analog signal) Cable
NOTE
This is a simplified representation of the rear view.
This rear view represents a general model; your display may differ from the view as shown.
When using a D-Sub signal input cable connector
for Macintosh
Mac adapter : For Apple Macintosh use, a
separate plug adapter is needed to change the
15 pin high density (3 row) D-sub VGA
connector on the supplied cable to a 15 pin 2
row connector.
Varies according to model.
Wall-outlet type
DVI-D (This feature is not available in all countries.)
B
A
PC
PC
3. Press the power button on the front panel to turn the power on. When monitor power is
turned on, the 'Self Image Setting Function' is executed automatically.
(Only Analog Mode)
Power Button
NOTE
‘ Self Image Setting Function’? This function provides the user with optimal display
settings.When the user connects the monitor for the first time, this function automatically adjusts
the display to optimal settings for individual input signals.
‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters, screen
flicker or tilted screen while using the device or after changing screen resolution, press the
AUTO function button to improve resolution.
9
Connecting the Display
W1946S/W1946SN/W2046S/W2246S/W2346S
Connecting with the PC
1. Before setting up the monitor, ensure that the power to the monitor, the computer
2. sCyosntenmec, tasnidgnoathleinrpautttaccahbedledeviceasnids ptuorwneedr ocoff.rd
in order, then tighten the screw
1
2
of the signal cable.
A
Connect D-sub(Analog signal) Cable
NOTE
This is a simplified representation of the rear view.
This rear view represents a general model; your display may differ from the view as shown.
When using a D-Sub signal input cable connector for
Macintosh
Mac adapter :For Apple Macintosh use, a
separate plug adapter is needed to change the
15 pin high density (3 row) D-sub VGA
connector on the supplied cable to a 15 pin 2
row connector.
Varies according to model.
Wall-outlet type
A
PC
3. Press the power button on the front panel to turn the power on. When monitor power is
turned on, the 'Self Image Setting Function' is executed automatically.
Power Button
NOTE
‘ Self Image Setting Function’? This function provides the user with optimal display
settings.When the user connects the monitor for the first time, this function automatically adjusts
the display to optimal settings for individual input signals.
‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters, screen
flicker or tilted screen while using the device or after changing screen resolution, press the
AUTO function button to improve resolution.
10
Connecting the Display
Using the cable holder (This feature is not available in all models.)
W1946T/W1946TN/W2046T
3
Cable holder
1
2
W1946S/W1946SN/W2046S
3
Cable holder
1
2
11
Control Panel Functions
Front Panel Controls
W1946T/W1946TN/W2046T/W2246T/W2346T
W1946S/W1946SN/W2046S/W2246S/W2346S
MENU Button
OSD LOCKED/UNLOCKED
This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
Press and hold the MENU button for several seconds.
The message "OSD LOCKED" should appear.
You can unlock the OSD controls at any time by pushing
the MENU button for several seconds. The message
"OSD UNLOCKED" should appear.
12
Control Panel Functions
MODE Button
Use this button to enter F-ENGINE, ORIGINAL
RATIO menus.
For more information, refer to page 20.
AUTO Button
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always press the
AUTO button before entering the On Screen
Display(OSD). (Only Analog Mode)
This will automatically adjust your display image to the
ideal settings for the current screen resolution size
(display mode).
The best display mode is
W1946S/W1946SN/W1946T/W1946TN : 1360 x 768
W2046S/W2046T : 1600 x 900
W2246S/W2346S/W2246T/W2346T : 1920 x1080
When two input signals are connected, you can select the
input signal (D-SUB/DVI) you want. When only one signal
is connected, it is automatically detected. The default
setting is D-Sub.
INPUT Button
(SOURCE Hot key)
(Only W1946T/W1946TN/W2046T/W2246T/W2346T )
EXIT Button
Exit the OSD(On Screen Display).
Use this button to turn the display on or off.
Power Button &
Power Indicator
The power indicator stays white if the display is running
properly (On Mode). If the display is in Sleep Mode
(Energy Saving), the power indicator is blinking white.
13
On Screen Display (OSD) Control Adjustment
Screen Adjustment
Making adjustments to the image size, position and operating
parameters of the display is quick and easy with the On Screen
Display Control system.
A short example is given below to familiarize you with the use of the
controls. The following section is an outline of the available
adjustments and selections you can make using the OSD.
To make adjustments in the On Screen Display, follow these steps:
Press the discretionary Button, then the main menu of the OSD appears.
1
To access a control, use the corresponding Buttons.
2
Use the
Use the
/
Buttons to adjust the image to the desired level.
3
4
Button to select other sub-menu items.
Press the EXIT Button to exit from the OSD.
14
On Screen Display(OSD) Selection and Adjustment
The following table indicates all the On Screen Display control, adjustment,
and setting menus.
DSUB : D-SUB(Analog signal) input
DVI-D : DVI-D(Digital signal) input
Main menu
PICTURE
Sub-menu
BRIGHTNESS
Supported input
Description
To adjust the brightness, contrast
and sharpness of the screen
DSUB
DVI-D
CONTRAST
SHARPNESS
To customize the color of the
screen
COLOR TEMP
(PRESET / USER)
DSUB
DVI-D
COLOR
GAMMA
HORIZONTAL
VERTICAL
To adjust the position of the
screen
DISPLAY
DSUB
DSUB
CLOCK
PHASE
To improve the clarity and
stability of the screen
DSUB
DVI-D
LANGUAGE
OTHERS
To customize the screen status
for a user's operating
environment
POWER INDICATOR
DSUB
WHITE BALANCE
FACTORY RESET
DSUB
DVI-D
DSUB
DVI-D
NORMAL
MOVIE
F-ENGINE
To select or customize desired
image settings
INTERNET
DEMO
DSUB
DVI-D
WIDE
ORIGINAL
ORIGINAL
RATIO
To adjust the image size
NOTE
The order of icons may differ depending on the model (15~22).
15
On Screen Display(OSD) Selection and Adjustment
You were introduced to the procedure of selecting and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
Press the MENU Button, then the main menu of the OSD appears.
Menu Name
Sub-
menus
Icons
Button
Tip
Exit
Adjust (Decrease/Increase)
Select another sub-menu
Restart to select sub-menu
NOTE
OSD (On Screen Display) menu languages on the monitor may differ from the manual.
16
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
To adjust the brightness of the screen.
To adjust the contrast of the screen.
To adjust the clearness of the screen.
BRIGHTNESS
CONTRAST
SHARPNESS
Exit : Exit
: Decrease
: Increase
: Select another sub-menu
: Restart to select sub-menu
COLOR TEMP
Select the screen color.
• sRGB: Set the screen color to fit the
sRGB standard color
PRESET
specification.
• 6500K-7500K: Red screen color.
• 8500K-9300K: Blue screen color.
Exit : Exit
USER
RED
: Decrease
Set your own red color levels.
: Increase
GREEN
Set your own green color levels.
: Select another sub-menu
: Restart to select sub-menu
BLUE
Set your own blue color levels.
GAMMA
Set your own gamma value. : 0 / 1 / 2
On the monitor, high gamma values
display whitish images and low
gamma values display blackish
images.
17
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
W1946T/W1946TN/W2046T/W2246T/W2346T
HORIZONTAL
To move image left and right.
To move image up and down.
VERTICAL
CLOCK
To minimize any vertical bars or
stripes visible on the screen
background.
The horizontal screen size will also
change.
W1946S/W1946SN/W2046S/W2246S/W2346S
To adjust the focus of the display.
This item allows you to remove any
horizontal noise and clear or sharpen
the image of characters.
PHASE
Exit : Exit
: Decrease
: Increase
: Select another sub-menu
: Restart to select sub-menu
18
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
To choose the language in which the
control names are displayed.
LANGUAGE
Use this function to set the power
indicator on the front side of the monitor
to ON or OFF.
POWER
INDICATOR
If you set OFF, it will go off.
If you set ON at any time, the power
indicator will automatically be turned on.
Exit : Exit
: Decrease
WHITE
BALANCE
If the output of the video card is
different the required specifications,
the color level may deteriorate due
to video signal distortion. Using this
function, the signal level is adjusted
to fit into the standard output level of
the video card in order to provide the
optimal image.
: Increase
: Select another sub-menu
: Restart to select sub-menu
Activate this function when white
and black colors are present in the
screen.
Restore all factory default settings except
FACTORY
RESET
"LANGUAGE."
Press the
,
buttons to reset
immediately.
NOTE
If this does not improve the screen image, restore the factory default settings. If necessary, execute the
WHITE BALANCE function again. This function will be enabled only when the input signal is an analog
signal.
19
On Screen Display(OSD) Selection and Adjustment
You were introduced to the procedure of selecting and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
Press the MODE Button, then the main menu of the OSD appears.
Menu Name
Sub-
menus
Icons
Button
Tip
Exit
Move
Select another sub-menu
NOTE
OSD (On Screen Display) menu languages on the monitor may differ from the manual.
20
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
NORMAL
Select this when you want to use the product
in the most general using environment.
MOVIE
Select this when you are watching a video or
movie.
INTERNET
Select this when you are working on the
document (Word etc.)
DEMO
This is used for advertising in the store. The
screen will be divided to show the standard
mode on the left and video mode on the right so
that the consumers can check the difference
after applying the video mode.
Exit : Exit
: Move
: Select another sub-menu
,
21
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
WIDE
Switch to full screen mode according to
input image signal.
ORIGINAL Change the input image signal ratio to
original.
* This function works only if input
resolution is lower than monitor ratio
(16:9).
Exit : Exit
: Move
: Select another sub-menu
,
22
Troubleshooting
Check the following before calling for service.
No image appears
G Is the power cord of the
•
•
Check and see if the power cord is connected
properly to the power outlet.
display connected?
G Is the power indicator
Press the Power button.
light on?
G Is the power indicator
•
If the display is in power saving mode, try moving
the mouse or pressing any key on the keyboard to
bring up the screen.
flickering?
• Try to turn on the PC
.
G Do you see an "OUT OF
RANGE" message on
the screen?
•
•
This message appears when the signal from the
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
This message appears when the signal cable
between your PC and your display is not
connected. Check the signal cable and try again.
G Do you see a "CHECK
SIGNAL CABLE"
message on the
screen?
Do you see a "OSD LOCKED" message on the screen?
G
Do you see “OSD
LOCKED” when you
push MENU button?
• You can secure the current control settings,
so that they cannot be inadvertently changed.
You can unlock the OSD controls at any time
by pushing the MENU button for several
seconds: the message
“OSD UNLOCKED” will appear.
23
Troubleshooting
Display image is incorrect
G Display Position is
•
Press the AUTO button to automatically adjust
your display image to the ideal setting.
If the results are unsatisfactory, adjust the image
position using the H position and V position icon
in the on screen display.
incorrect.
•
Press the AUTO button to automatically adjust
your display image to the ideal setting.
If the results are unsatisfactory, decrease the
vertical bars or stripes using the CLOCK icon in
the on screen display.
G On the screen
background, vertical
bars or stripes are
visible.
•
•
Press the AUTO button to automatically adjust
your display image to the ideal setting.
If the results are unsatisfactory, decrease the
horizontal bars using the PHASE icon in the on
screen display.
Check Control Panel --> Display --> Settings
and adjust the display to the recommended
resolution or adjust the display image to the ideal
setting. Set the color setting higher than 24 bits
(true color).
G Any horizontal noise
appearing in any
image or characters
are not clearly
portrayed.
IMPORTANT
Check Control Panel --> Display --> Settings and see if the frequency or the
resolution were changed. If yes, readjust the video card to the recommend
resolution.
If the recommended resolution (optimal resolution) is not selected, letters may be
blurred and the screen may be dimmed, truncated or biased. Make sure to select
the recommend resolution.
The setting method can differ by computer and O/S (Operation System),
and resolution mentioned above may not be supported by the video card
performance. In this case, please ask to the computer or the video card
manufacturer.
24
Troubleshooting
Display image is incorrect
G The screen color is
•
•
•
Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
Make sure the video card is properly inserted in
the slot.
Set the color setting higher than 24 bits (true color)
at Control Panel - Settings.
mono or abnormal.
G The screen blinks.
•
Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Do you see an "Unrecognized monitor, Plug&Play (VESA
DDC) monitor found" message?
G
Have you installed the
display driver?
•
Be sure to install the display driver from the display
driver CD (or diskette) that comes with your
display. Or, you can also download the driver from
•
Make sure to check if the video card supports
Plug&Play function.
25
Specifications
W1946T/W1946TN
47.0 cm (18.5 inch) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Display
Visible diagonal size : 47.0 cm
0.300 x 0.300 mm (Pixel pitch)
Horizontal Freq.
Vertical Freq.
Input Form
30 kHz to 61 kHz (Automatic)
56 Hz to 75 Hz (Automatic)
Separate Sync.
Sync Input
Video Input
SOG (Sync On Green), Digital
Signal Input
Input Form
15 pin D-Sub Connector
DVI-D Connector (Digital)
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Max
Recommend
VESA 1360 x 768 @60 Hz
VESA 1360 x 768 @60 Hz
Resolution
Plug&Play
DDC 2B(Digital),DDC2AB(Anlaog)
:
≤
≤
22 W(Typ.)
0.5 W
0.5 W
On Mode
Power
Consumption
Sleep Mode
Off Mode
With Stand
Without Stand
Dimensions
& Weight
Width 44.26 cm ( 17.42 inch)
Height 35.62 cm ( 14.02 inch)
Depth 16.99 cm ( 6.68 inch)
Width 44.26 cm ( 17.42 inch)
Height 26.67 cm (10.50 inch)
Depth 6.04 cm ( 2.37 inch)
Weight(excl. packing)
3.0 kg (6.66 lb)
Tilt : -5˚ to 15˚
Range
AC 100-240 V~ 50 / 60 Hz 0.8 A
Power Input
Operating Conditions
Environment
al Conditions
Temperature
Humidity
10 ˚C to 35 ˚C
10 % to 80 % non-Condensing
Storage Conditions
Temperature
Humidity
-20 ˚C to 60 ˚C
5 % to 90 % non-Condensing
Attached ( ), Detached ( O )
Wall-outlet type
Stand Base
Power cord
NOTE
Information in this document is subject to change without notice.
26
Specifications
W1946S/W1946SN
47.0 cm (18.5 inch) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Display
Visible diagonal size : 47.0 cm
0.300 x 0.300 mm (Pixel pitch)
Horizontal Freq.
Vertical Freq.
Input Form
30 kHz to 61 kHz (Automatic)
56 Hz to 75 Hz (Automatic)
Separate Sync.
Sync Input
Video Input
SOG (Sync On Green)
Signal Input
Input Form
15 pin D-Sub Connector
RGB Analog (0.7 Vp-p/ 75 ohm)
Max
Recommend
VESA 1360 x 768 @60 Hz
VESA 1360 x 768 @60 Hz
Resolution
Plug&Play
DDC 2AB
:
≤
≤
22 W(Typ.)
0.5 W
0.5 W
On Mode
Power
Consumption
Sleep Mode
Off Mode
With Stand
Without Stand
Dimensions
& Weight
Width 44.26 cm (17.42 inch)
Height 35.62 cm (14.02 inch)
Depth 16.99 cm ( 6.68 inch)
Width 44.26 cm (17.42 inch)
Height 26.67 cm (10.50 inch)
Depth 6.04 cm ( 2.37 inch)
Weight(excl. packing)
3.0 kg (6.66 lb)
Tilt : -5˚ to 15˚
Range
AC 100-240 V~ 50 / 60 Hz 0.8 A
Power Input
Operating Conditions
Environment
al Conditions
Temperature
Humidity
10 ˚C to 35 ˚C
10 % to 80 % non-Condensing
Storage Conditions
Temperature
Humidity
-20 ˚C to 60 ˚C
5 % to 90 % non-Condensing
Attached ( ), Detached ( O )
Wall-outlet type
Stand Base
Power cord
NOTE
Information in this document is subject to change without notice.
27
Specifications
W2046T
50.8 cm (20.0 inch) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Display
Visible diagonal size : 50.8 cm
0.2766 x 0.2766 mm (Pixel pitch)
Horizontal Freq.
Vertical Freq.
Input Form
30 kHz to 83 kHz (Automatic)
56 Hz to 75 Hz (Automatic)
Separate Sync.
Sync Input
Video Input
SOG (Sync On Green), Digital
Signal Input
Input Form
15 pin D-Sub Connector
DVI-D Connector (Digital)
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Max
Recommend
VESA 1600 x 900 @ 60 Hz
VESA 1600 x 900 @ 60 Hz
Resolution
Plug&Play
DDC 2B(Digital),DDC2AB(Anlaog)
:
≤
≤
24 W(Typ.)
0.5 W
0.5 W
On Mode
Power
Consumption
Sleep Mode
Off Mode
With Stand
Without Stand
Dimensions
& Weight
Width 47.58 cm (18.73 inch)
Height 37.64 cm (14.81 inch)
Depth 16.99 cm ( 6.68 inch)
Width 47.58 cm (18.73 inch)
Height 30.35 cm ( 11.94 inch)
Depth 6.08 cm ( 2.39 inch)
Weight(excl. packing)
3.2 kg (7.11 lb)
Tilt : -5˚ to 15˚
Range
AC 100-240 V~ 50 / 60 Hz 1.0 A
Power Input
Operating Conditions
Environment
al Conditions
Temperature
Humidity
10 ˚C to 35 ˚C
10 % to 80 % non-Condensing
Storage Conditions
Temperature
Humidity
-20 ˚C to 60 ˚C
5 % to 90 % non-Condensing
Attached ( ), Detached ( O )
Wall-outlet type
Stand Base
Power cord
NOTE
Information in this document is subject to change without notice.
28
Specifications
W2046S
50.8 cm (20.0 inch) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Display
Visible diagonal size : 50.8 cm
0.2766 x 0.2766 mm (Pixel pitch)
Horizontal Freq.
Vertical Freq.
Input Form
30 kHz to 83 kHz (Automatic)
56 Hz to 75 Hz (Automatic)
Separate Sync.
Sync Input
Video Input
SOG (Sync On Green)
Signal Input
Input Form
15 pin D-Sub Connector
RGB Analog (0.7 Vp-p/ 75 ohm)
Max
Recommend
VESA 1600 x 900 @ 60 Hz
VESA 1600 x 900 @ 60 Hz
Resolution
Plug&Play
DDC 2AB
:
≤
≤
24 W(Typ.)
0.5 W
0.5 W
On Mode
Power
Consumption
Sleep Mode
Off Mode
With Stand
Without Stand
Dimensions
& Weight
Width 47.58 cm ( 18.73 inch)
Height 37.64 cm ( 14.81 inch)
Depth 16.99 cm ( 6.68 inch)
Width 47.58 cm ( 18.73 inch)
Height 30.35 cm ( 11.94 inch)
Depth 6.08 cm ( 2.39 inch)
Weight(excl. packing)
3.2 kg (7.11 lb)
Tilt : -5˚ to 15˚
Range
AC 100-240 V~ 50 / 60 Hz 1.0 A
Power Input
Operating Conditions
Environment
al Conditions
Temperature
Humidity
10 ˚C to 35 ˚C
10 % to 80 % non-Condensing
Storage Conditions
Temperature
Humidity
-20 ˚C to 60 ˚C
5 % to 90 % non-Condensing
Attached ( ), Detached ( O )
Wall-outlet type
Stand Base
Power cord
NOTE
Information in this document is subject to change without notice.
29
Specifications
W2246T
54.6 cm (21.5 inch) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Display
Visible diagonal size : 54.6 cm
0.248 x 0.248 mm (Pixel pitch)
Horizontal Freq.
Vertical Freq.
Input Form
30 kHz to 83 kHz (Automatic)
56 Hz to 75 Hz (Automatic)
Separate Sync.
Sync Input
Video Input
SOG (Sync On Green), Digital
Signal Input
Input Form
15 pin D-Sub Connector
DVI-D Connector (Digital)
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Max
Recommend
VESA 1920 x 1080 @60 Hz
VESA 1920 x 1080 @60 Hz
Resolution
Plug&Play
DDC 2B(Digital),DDC2AB(Anlaog)
:
≤
≤
24 W(Typ.)
0.5 W
0.5 W
On Mode
Power
Consumption
Sleep Mode
Off Mode
With Stand
Without Stand
Dimensions
& Weight
Width 50.92 cm ( 20.04 inch)
Height 39.69 cm ( 15.62 inch)
Depth 21.00 cm ( 8.26 inch)
Width 50.92 cm ( 20.04 inch)
Height 30.42 cm ( 11.97 inch)
Depth 5.98 cm ( 2.35 inch)
Weight(excl. packing)
3.5 kg (7.77 lb)
Tilt : -5˚ to 15˚
Range
AC 100-240 V~ 50 / 60 Hz 1.0 A
Power Input
Operating Conditions
Environment
al Conditions
Temperature
Humidity
10 ˚C to 35 ˚C
10 % to 80 % non-Condensing
Storage Conditions
Temperature
Humidity
-20 ˚C to 60 ˚C
5 % to 90 % non-Condensing
Attached ( ), Detached ( O )
Wall-outlet type
Stand Base
Power cord
NOTE
Information in this document is subject to change without notice.
30
Specifications
W2246S
54.6 cm (21.5 inch) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Display
Visible diagonal size : 54.6 cm
0.248 x 0.248 mm (Pixel pitch)
Horizontal Freq.
Vertical Freq.
Input Form
30 kHz to 83 kHz (Automatic)
56 Hz to 75 Hz (Automatic)
Separate Sync.
Sync Input
Video Input
SOG (Sync On Green)
Signal Input
Input Form
15 pin D-Sub Connector
RGB Analog (0.7 Vp-p/ 75 ohm)
Max
Recommend
VESA 1920 x 1080 @60 Hz
VESA 1920 x 1080 @60 Hz
Resolution
Plug&Play
DDC 2AB
:
≤
≤
24 W(Typ.)
0.5 W
0.5 W
On Mode
Power
Consumption
Sleep Mode
Off Mode
With Stand
Without Stand
Dimensions
& Weight
Width 50.92 cm ( 20.04 inch)
Height 39.69 cm ( 15.62 inch)
Depth 21.00 cm ( 8.26 inch)
Width 50.92 cm ( 20.04 inch)
Height 30.42 cm ( 11.97 inch)
Depth 5.98 cm ( 2.35 inch)
Weight(excl. packing)
3.5 kg (7.77 lb)
Tilt : -5˚ to 15˚
Range
AC 100-240 V~ 50 / 60 Hz 1.0 A
Power Input
Operating Conditions
Environment
al Conditions
Temperature
Humidity
10 ˚C to 35 ˚C
10 % to 80 % non-Condensing
Storage Conditions
Temperature
Humidity
-20 ˚C to 60 ˚C
5 % to 90 % non-Condensing
Attached ( ), Detached ( O )
Wall-outlet type
Stand Base
Power cord
NOTE
Information in this document is subject to change without notice.
31
Specifications
W2346T
58.4 cm (23 inch) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Display
Visible diagonal size : 58.4 cm
0.266 x 0.266 mm (Pixel pitch)
Horizontal Freq.
Vertical Freq.
Input Form
30 kHz to 83 kHz (Automatic)
56 Hz to 75 Hz (Automatic)
Separate Sync.
Sync Input
Video Input
SOG (Sync On Green), Digital
Signal Input
Input Form
15 pin D-Sub Connector
DVI-D Connector (Digital)
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Max
Recommend
VESA 1920 x 1080 @60 Hz
VESA 1920 x 1080 @60 Hz
Resolution
Plug&Play
DDC 2B(Digital),DDC2AB(Anlaog)
:
≤
≤
27 W(Typ.)
0.5 W
0.5 W
On Mode
Power
Consumption
Sleep Mode
Off Mode
With Stand
Without Stand
Dimensions
& Weight
Width 54.25 cm ( 21.35 inch)
Height 41.66 cm ( 16.40 inch)
Depth 21.00 cm ( 8.26 inch)
Width 54.25 cm ( 21.35 inch)
Height 32.30 cm ( 12.71 inch)
Depth 6.05 cm ( 2.38 inch)
Weight(excl. packing)
4.2 kg (9.33 lb)
Tilt : -5˚ to 15˚
Range
AC 100-240 V~ 50 / 60 Hz 1.0 A
Power Input
Operating Conditions
Environment
al Conditions
Temperature
Humidity
10 ˚C to 35 ˚C
10 % to 80 % non-Condensing
Storage Conditions
Temperature
Humidity
-20 ˚C to 60 ˚C
5 % to 90 % non-Condensing
Attached ( ), Detached ( O )
Wall-outlet type
Stand Base
Power cord
NOTE
Information in this document is subject to change without notice.
32
Specifications
W2346S
58.4 cm (23 inch) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Display
Visible diagonal size : 58.4 cm
0.266 x 0.266 mm (Pixel pitch)
Horizontal Freq.
Vertical Freq.
Input Form
30 kHz to 83 kHz (Automatic)
56 Hz to 75 Hz (Automatic)
Separate Sync.
Sync Input
Video Input
SOG (Sync On Green)
Signal Input
Input Form
15 pin D-Sub Connector
RGB Analog (0.7 Vp-p/ 75 ohm)
Max
Recommend
VESA 1920 x 1080 @60 Hz
VESA 1920 x 1080 @60 Hz
Resolution
Plug&Play
DDC 2AB
:
≤
≤
27 W(Typ.)
0.5 W
0.5 W
On Mode
Power
Consumption
Sleep Mode
Off Mode
With Stand
Without Stand
Dimensions
& Weight
Width 54.25 cm (21.35 inch)
Height 41.66 cm (16.40 inch)
Depth 21.00 cm ( 8.26 inch)
Width 54.25 cm ( 21.35 inch)
Height 32.30 cm ( 12.71 inch)
Depth 6.05 cm ( 2.38 inch)
Weight(excl. packing)
4.2 kg (9.33 lb)
Tilt : -5˚ to 15˚
Range
AC 100-240 V~ 50 / 60 Hz 1.0 A
Power Input
Operating Conditions
Environment
al Conditions
Temperature
Humidity
10 ˚C to 35 ˚C
10 % to 80 % non-Condensing
Storage Conditions
Temperature
Humidity
-20 ˚C to 60 ˚C
5 % to 90 % non-Condensing
Attached ( ), Detached ( O )
Wall-outlet type
Stand Base
Power cord
NOTE
Information in this document is subject to change without notice.
33
Specifications
Preset Modes (Resolution)
W1946T/W1946TN/W1946S/W1946SN
Display Modes (Resolution) Horizontal Freq. (kHz)
Vertical Freq. (Hz)
1
2
31.468
31.469
37.500
37.879
46.875
49.725
48.363
60.123
47.712
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1360 x 768
70
60
75
60
75
75
60
75
60
3
4
5
6
7
8
*9
*Recommend Mode
W2046T/W2046S
Display Modes (Resolution)
Horizontal Freq. (kHz)
Vertical Freq. (Hz)
1
2
31.468
31.469
37.500
37.879
46.875
48.363
60.123
67.500
60.000
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
1024 x 768
1024 x 768
1152 x 864
1600 x 900
70
60
75
60
75
60
75
75
60
3
4
5
6
7
8
*9
*Recommend Mode
34
Specifications
W2246T/W2346T/W2246S/W2346S
Display Modes (Resolution)
Horizontal Freq. (kHz)
Vertical Freq. (Hz)
1
2
31.468
31.469
37.500
37.879
46.875
48.363
60.123
67.500
63.981
79.976
65.290
67.500
720 x 400
640 x 480
70
60
75
60
75
60
75
75
60
75
60
60
3
640 x 480
4
800 x 600
800 x 600
5
6
1024 x 768
1024 x 768
1152 x 864
1280 x 1024
1280 x 1024
1680 x 1050
1920 x 1080
7
8
9
10
11
*12
*Recommend Mode
Indicator
LED Color
MODE
White
White Blinking
Off
On Mode
Sleep Mode
Off Mode
35
Installing the Wall mount plate
This monitor satisfies the specifications of the Wall mount plate or
the interchange device.
1. Place the monitor with its front facing downward on a soft cloth.
2. Separate the stand by pushing the PUSH button.
Good Position
Bad Position
Warning:
You can hurt your finger.
3. Install the Wall mount plate.
Wall mount plate(Separate purchase)
This is stand-type or wall mount type and is
connectable with Wall mount plate.
Please refer to the installation guide for more details,
which is provided when Wall mount plate is purchased.
- Be sure to use screws and a wall mount that
meet VESA standards.
- Using screws longer than those
recommended might damage the product.
- Using screws that do not meet VESA
standards might either damage the product
or result in it coming away from the wall.We
will not be held responsible for any damage
resulting from failure to follow these
instructions.
<Please use VESA standard as a recommendation.>
Mounting crew:
Interface pad thickness: 2.6mm
Screw :
4mm x pitch 0.7mm x length 10mm
Kensington Security Slot
Connected to a locking cable that can be
purchased separately at most computer stores.
36
Digitally yours
|