OWNER’S MANUAL
Blu-ray Disc™/DVD Player
Please read this manual carefully before operating
your set and retain it for future reference.
BP120
P/NO : MFLxxxxxxxxxxx
Getting Started
3
Safety Information
CAUTION
CAUTION : CLASS 1M VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN. DO NOT VIEW DIRECTLY
WITH OPTICAL INSTRUMENTS
1
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
This lightning flash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
presence of uninsulated dangerous
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
centre. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
voltage within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a built-
in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
4
Getting Started
This device is equipped with a portable battery or
accumulator.
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
1
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
Getting Started
5
Notes on Copyrights
Important Notice for TV colour
system
The colour system of this player differs according to
currently playing discs.
Because AACS (Advanced Access Content
System) is approved as content protection
system for Blu-ray Disc format, similar to use of
CSS (Content Scramble System) for DVD format,
certain restrictions are imposed on playback,
analog signal output, etc., of AACS protected
contents. The operation of this product and
restrictions on this product may vary depending
on your time of purchase as those restrictions
may be adopted and/or changed by AACS after
the production of this product.
y
1
For example, when the player plays the disc
recorded in the NTSC colour system, the image is
output as an NTSC signal.
Only the multi system colour TV can receive all
signals output from the player.
If you have a PAL colour system TV, you will see
just distorted images when using discs or video
contents recorded in NTSC.
y
Furthermore, BD-ROM Mark and BD+ are
y
additionally used as content protection systems
for Blu-ray Disc format, which imposes certain
restrictions including playback restrictions for
BD-ROM Mark and/or BD+ protected contents.
To obtain additional information on AACS, BD-
ROM Mark, BD+, or this product, please contact
an authorized Customer Service Centre.
The multi system colour TV changes the colour
system automatically according to input signals.
In case that the colour system is not changed
automatically, turn it off and then on to see
normal images on screen.
y
Even if the disc recorded in NTSC colour system
are well displayed on your TV, these may not be
recorded correctly on your recorder.
y
Many BD-ROM/DVD discs are encoded with
copy protection. Because of this, you should only
connect your player directly to your TV, not to a
VCR. Connecting to a VCR results in a distorted
picture from copy-protected discs.
y
y
This product incorporates copyright protection
technology that is protected by U.S. patents
and other intellectual property rights. Use of
this copyright protection technology must be
authorized by Rovi, and is intended for home and
other limited viewing uses only unless otherwise
authorized by Rovi. Reverse engineering or
disassembly is prohibited.
Under the U.S. Copyright laws and Copyright
laws of other countries, unauthorized recording,
use, display, distribution, or revision of television
programs, videotapes, BD-ROM discs, DVDs, CDs
and other materials may subject you to civil and/
or criminal liability.
y
6
Table of Contents
4
Operating
Table of Contents
26 General Playback
26 – Using [HOME] menu
26 – Playing a Disc
26 – Playing a file on disc/USB device
27 – Basic operations for video and audio
content
27 – Basic operations for photo content
27 – Using the disc menu
28 – Resume playback
28 – Last Scene Memory
28 Advanced Playback
28 – Repeat Playback
29 – Repeating a specific portion
29 – Viewing content information
29 – Changing content list view
30 – Selecting a subtitle file
30 – Options while viewing a photo
31 – Listening to music while slide show
1
Getting Started
3
8
8
Safety Information
Introduction
– Playable Discs and symbols used in
this manual
– About the “7” Symbol Display
– Compatibility Notes
9
9
10 – File requirement
11
– AVCHD (Advanced Video Codec High
Definition)
12 – Certain System Requirements
12 – Regional Code
12 – System Select
13
14
14
Remote control
Front panel
Rear panel
31
On-Screen display
31 – Displaying content information on-
screen
2
Connecting
32 – Playing from selected time
32 – Selecting a subtitle language
33 – Hearing a different audio
33 – Watching from a different angle
33 – Changing the TV Aspect Ratio
34 – Changing subtitle code page
34 – Changing the Picture Mode
35 Audio CD recording
15
Connecting to Your TV
15 – HDMI Connection
16 – What is SIMPLINK?
16 – Resolution Setting
17
Connecting to an Amplifier
18 – Connecting to an Amplifier via HDMI
Output
18 – Connecting to an Amplifier via Digital
Audio Output
19
USB device connection
19 – Playback content in the USB device
3
System Setting
20 Settings
20 – Initial Setup
20 – Adjust the Setup Settings
21 – [DISPLAY] Menu
22 – [LANGUAGE] Menu
23 – [AUDIO] Menu
24 – [LOCK] Menu
25 – [OTHERS] Menu
Table of Contents
7
5
Troubleshooting
36 Troubleshooting
36 – General
37 – Picture
37 – Customer Support
37 – Open source software notice
1
6
Appendix
2
3
4
5
6
38 Controlling a TV with the Supplied
Remote Control
38 – Setting up the remote to control your
TV
39 Area Code List
40 Language code List
41
Trademarks and Licenses
43 Audio Output Specifications
45 Specifications
46 Maintenance
46 – Handling the Unit
46 – Notes on Discs
8
Getting Started
Introduction
1
Playable Discs and symbols used in this manual
Media/Term
Logo
Symbol
Description
Discs such as movies that can be purchased or
rented.
y
e
BD-R/RE discs that are recorded in BDAV format.
y
y
Blu-ray
BD-R/RE discs that contain Movie, Music or
Photo files.
y
u
i
ISO 9660+JOLIET, UDF and UDF Bridge format
y
y
Discs such as movies that can be purchased or
rented.
r
Movie mode and finalized only
Supports the dual layer disc also
y
y
DVD-ROM
DVD-R
Finalized AVCHD format
DVD-RW
DVD+R
o
DVD+RW
(8 cm, 12 cm)
DVD R/RW discs that contain Movie, Music or
Photo files.
y
y
y
u
i
ISO 9660+JOLIET, UDF and UDF Bridge format
DVD-RW (VR)
(8 cm, 12 cm)
VR mode and finalized only
Audio CD
r
t
Audio CD
(8 cm, 12 cm)
CD-R/RW discs that contain Movie, Music or
Photo files.
y
y
y
u
i
CD-R/RW
(8 cm, 12 cm)
ISO 9660+JOLIET, UDF and UDF Bridge format
Indicates special notes and operating features.
Note
–
–
,
>
Indicates cautions for preventing possible
damages from abuse.
Caution
Getting Started
9
Note
,
About the “ ” Symbol Display
7
Depending on the conditions of the
recording equipment or the CD-R/RW (or
DVD R/RW) disc itself, some CD-R/RW (or
DVD R/RW) discs cannot be played on the
unit.
y
“7”may appear on your TV display during
operation and indicates that the function explained
in this owner’s manual is not available on that
specific media.
1
Depending on the recording software & the
finalization, some recorded discs (CD-R/RW,
DVD R/RW, BD-R/RE) may not be playable.
y
y
Compatibility Notes
Because BD-ROM is a new format, certain disc,
digital connection and other compatibility issues
are possible. If you experience compatibility
problems, please contact an authorized
Customer Service Center.
y
BD-R/RE, DVD R/RW and CD-R/RW discs
recorded using a personal computer or a
DVD or CD Recorder may not play if the
disc is damaged or dirty, or if there is dirt or
condensation on the player’s lens.
This unit allows you to enjoy functions such
as picture-in-picture, secondary audio and
Virtual packages, etc., with BD-ROM supporting
BONUSVIEW (BD-ROM version 2 Profile 1 version
1.1). Secondary video and audio can be played
from a disc compatible with the picture-in-
picture function. For the playback method, refer
to the instructions in the disc.
y
If you record a disc using a personal
computer, even if it is recorded in a
compatible format, there are cases in which
it may not play because of the settings of
the application software used to create the
disc. (Check with the software publisher for
more detailed information.)
y
This player requires discs and recordings to
meet certain technical standards in order to
achieve optimal playback quality.
y
y
Viewing high-definition content and up-
converting standard DVD content may require a
HDMI-capable input or HDCP-capable DVI input
on your display device.
y
Pre-recorded DVDs are automatically set to
these standards. There are many different
types of recordable disc formats (including
CD-R containing MP3 or WMA files) and
these require certain pre-existing conditions
to ensure compatible playback.
Some BD-ROM and DVD discs may restrict the
use of some operation commands or features.
y
y
Dolby TrueHD, Dolby Digital Plus and DTS-HD are
supported with maximum 7.1 channels if you
use HDMI connection for the audio output of the
unit.
Customers should note that permission
is required in order to download MP3 /
WMA files and music from the Internet.
Our company has no right to grant such
permission. Permission should always be
sought from the copyright owner.
y
y
You can use a USB device to store some disc
related information. The disc you are using will
control how long this information is retained.
y
You have to set the disc format option
to [Mastered] in order to make the discs
compatible with the LG players when
formatting rewritable discs. When setting
the option to Live System, you cannot use
it on LG player. (Mastered/Live File System :
Disc format system for windows Vista)
10 Getting Started
File requirement
Movie files
1
File
Location
File
Extension
Codec Format
Audio Format
Subtitle
“.avi”, “.divx”,
DIVX3.xx, DIVX4.xx,
Dolby Digital,
SubRip (.srt / .txt), SAMI (.smi),
“.mpg”, “.mpeg”, DIVX5.xx, DIVX6.xx
DTS, MP3, AAC, SubStation Alpha (.ssa/.txt),
“.mkv”, “.mp4”,
“.asf”, “.wmv”,
“.m4v”(DRM
free), “.vob”,
“.3gp”
(standard playback
only), XVID, MPEG1 SS,
H.264/MPEG-4 AVC,
MPEG2 PS, MPEG2 TS,
VC-1 SM (WMV3)
AC3
MicroDVD (.sub/.txt), VobSub
(.sub), SubViewer 1.0 (.sub),
SubViewer 2.0 (.sub/.txt), TMPlayer
(.txt), DVD Subtitle System (.txt)
Disc,
USB
Music files
File
Location
File
Extension
Sampling Frequency
Bitrate
Note
“mp3”, “.wav”,
“.m4a”(DRM
free), “.flac”
within 16 - 48 kHz (MP3) within 32 - 320
kbps (MP3)
Some wav files are
not supported on this
player.
Disc,
USB
Photo files
File
Location
File
Extension
Recommended
Size
Note
“.jpg”, “.jpeg”,
“.png”, “.gif”
Less than 4,000 x 3,000 x 24 bit/pixel Progressive and lossless
Less than 3,000 x 3,000 x 32 bit/pixel compression photo image files
are not supported.
Disc,
USB
Getting Started 11
Note
Note
,
,
The file name is limited to 180 characters.
A“avi”file which is encoded“WMV 9 codec”
is not supported.
y
y
y
y
Maximum files/Folder: Less than 2000 (total
number of files and folders)
This player supports UTF-8 files even if it
contains Unicode subtitle contents. This
player can not support the pure Unicode
subtitle files.
1
Depending on the size and number of the
files, it may take several minutes to read the
contents on the media.
y
y
Depending on the types of file or ways of
recording, it may not play back.
y
y
always compatible. There may be some
restrictions by file features.
A disc which was recorded by multi-session
on normal PC is not supported on this
player.
This unit cannot support the ID3 Tag
embedded MP3 file.
y
y
To be playback a movie file, movie file name
and Subtitle file name must be the same.
y
y
The total playback time of audio files
indicated on the screen may not correct for
VBR files.
If video codec is MPEG2 TS or MPEG2 PS,
subtitle does not play back.
HD movie files contained on the CD/DVD or
USB 1.0/1.1 may not played properly.
Blu-ray Disc or USB 2.0 are recommended to
play back HD movie files.
y
y
y
AVCHD (Advanced Video
Codec High Definition)
This player can playback AVCHD format discs.
These discs are normally recorded and used in
camcorders.
This player supports H.264/MPEG-4 AVC
profile Main, High at Level 4.1. For a file
with higher level, the warning message will
appear on the screen.
y
This player does not support files that are
The AVCHD format is a high definition digital
video camera format.
y
y
recorded with GMC 1 or Qpel
.
2
*
*
*1 GMC – Global Motion Compensation
*2 Qpel – Quarter pixel
The MPEG-4 AVC/H.264 format is capable of
compressing images at higher efficiency than
that of the conventional image compressing
format.
This player can playback AVCHD discs using
“x.v.Colour”format.
y
y
Some AVCHD format discs may not play
depending on the recording condition.
AVCHD format discs need to be finalized.
y
y
“x.v.Colour”offers a wider colour range than
normal DVD camcorder discs.
12 Getting Started
Certain System Requirements
Regional Code
This unit has a regional code printed on the rear of
the unit. This unit can play only BD-ROM or DVD
discs labelled same as the rear of the unit or“ALL”.
For high definition video playback:
High definition display that has HDMI input jack.
BD-ROM disc with high definition content.
y
y
y
1
HDMI or HDCP capable DVI input on your display
device is required for some content (as specified
by disc authors).
System Select
Open the disc tray using the B(OPEN/CLOSE)
button and then, press and hold M(PAUSE) for
more than five seconds to change the color system
(PAL /NTSC /AUTO).
For Dolby® Digital Plus, Dolby TrueHD and DTS-HD
multi-channel audio playback:
An amplifier/receiver with a built-in (Dolby
Digital, Dolby Digital Plus, Dolby TrueHD, DTS or
DTS-HD) decoder.
y
Main, center, surround speakers and subwoofer
as necessary for chosen format.
y
Getting Started 13
Remote control
• • • • • • a • • • • • •
• • • • • • d • • • • •
1(POWER): Switches the player REPEAT (h): Repeats a desired
1
ON or OFF.
section or sequence.
B(OPEN/CLOSE): Opens and
closes the disc tray.
AUDIO ([): Selects an audio
language.
0-9 numerical buttons: Selects
numbered options in a menu.
SUBTITLE (]): Selects a subtitle
language.
CLEAR: Removes a mark on the
search menu or a number when
setting the password.
TITLE/POP-UP: Displays the DVD
title menu or BD-ROM’s pop-up
menu, if available.
TV Control Buttons: See page
Colored (R, G, Y, B) buttons: Use
to navigate BD-ROM menus. They
are also used for [MOVIE], [PHOTO]
and [MUSIC] menu.
• • • • • • b • • • • •
c/v(SCAN): Searches
backward or forward.
C/V(SKIP): Goes to the
next or previous chapter / track /
file.
M(PAUSE): Pauses playback.
z(PLAY): Starts playback.
Z(STOP): Stops playback.
• • • • • • c • • • • •
Battery Installation
HOME (n): Displays or exits the
[Home Menu].
INFO/MENU (m): Displays or
exits On-Screen Display.
Direction buttons: Selects an
option in the menu.
ENTER (b): Acknowledges menu
Remove the battery cover on the
rear of the Remote Control, and
insert theR03 (size AAA) battery
with 4and 5matched correctly.
selection.
BACK (1): Exits the menu or
returns to the previous screen.
DISC MENU: Accesses menu on a
disc.
14 Getting Started
Front panel
1
a Disc Tray
e N(PLAY / PAUSE)
f Z(STOP)
b Display Window
c Remote Sensor
d B(OPEN/CLOSE)
g 1(POWER)
h USB Port
Rear panel
a AC power cord
c DIGITAL AUDIO OUT (COAXIAL)
b HDMI OUT
Connecting 15
Additional Information for HDMI
Connecting to Your TV
When you connect a HDMI or DVI compatible
device make sure of the following:
y
HDMI Connection
-
Try switching off the HDMI/DVI device and
this player. Next, switch on the HDMI/DVI
device and leave it for around 30 seconds,
then switch on this player.
If you have a HDMI TV or monitor, you can connect
it to this player using a HDMI cable (Type A, High
Speed HDMI™ Cable). Connect the HDMI jack on
the player to the HDMI jack on a HDMI compatible
TV or monitor.
-
-
The connected device’s video input is set
correctly for this unit.
2
The connected device is compatible with
720x576p, 1280x720p, 1920x1080i or
1920x1080p video input.
Rear of the unit
Not all HDCP-compatible HDMI or DVI devices
will work with this player.
y
-
The picture will not be displayed properly
with non-HDCP device.
Note
,
If a connected HDMI device does not accept
y
the audio output of the player, the HDMI
device’s audio sound may be distorted or
may not output.
HDMI
cable
When you use HDMI connection, you can
change the resolution for the HDMI output.
y
y
TV
Select the type of video output from the
HDMI OUT jack using [HDMI Color Setting]
option on the [Setup] menu (see page
Changing the resolution when the
connection has already been established
may result in malfunctions. To solve the
problem, turn off the player and then turn it
on again.
y
Set the TV’s source to HDMI (refer to TV’s Owner’s
manual).
When the HDMI connection with HDCP
is not verified, TV screen is changed to
black screen. In this case, check the HDMI
connection, or disconnect the HDMI cable.
y
y
If there are noises or lines on the screen,
please check the HDMI cable (length is
generally limited to 4.5 m(15 ft.)).
16 Connecting
What is SIMPLINK?
Resolution Setting
The player provides several output resolutions for
HDMI OUT jack. You can change the resolution
using [Setup] menu.
Some functions of this unit can be controlled
by the TV’s remote control when this unit and a
compatible LG TV with SIMPLINK are connected
through HDMI connection.
1. Press HOME (n).
2. Use a/dto select the [Setup] and press ENTER
(b). The [Setup] menu appears.
Controllable functions by LG TV’s remote control;
Play, Pause, Scan, Skip, Stop, Power Off, etc.
3. Use w/sto select [DISPLAY] option then press
dto move to the second level.
2
Refer to the TV owner’s manual for the details of
SIMPLINK function.
4. Use w/sto select the [Resolution] option then
press ENTER (b) to move to the third level.
LG TV’s with SIMPLINK function has the logo as
shown above.
Note
,
Depending on the disc type or playing status,
some SIMPLINK operations may differ from
your purpose or not work.
5. Use w/sto select the desired resolution then
press ENTER (b) to confirm your selection.
Connecting 17
Note
,
Connecting to an
If your TV does not accept the resolution
you have set on the player, you can set
resolution to 576p as follows:
y
Amplifier
1. Press Bto open the disc tray.
Make one of the following connections, depending
on the capabilities of your existing equipment.
2
Press Z(STOP) for more than 5 seconds.
When you set the resolution to 576i with
HDMI connection, actual resolution is
outputted to 576p.
y
y
HDMI Audio connection (page 18)
Digital Audio connection (page 18)
y
y
Since many factors affect the type of audio output,
see“Audio Output Specifications”for details (pages
2
If you select a resolution manually and then
connect the HDMI jack to TV and your TV
does not accept it, the resolution setting is
set to [Auto].
About Digital Multi-channel sound
If you select a resolution that your TV
does not accept, the warning message
will appear. After resolution change,
if you cannot see the screen, please
wait 20 seconds and the resolution will
automatically revert back to the previous
resolution.
y
y
A digital multi-channel connection provides the
best sound quality. For this, you need a multi-
channel Audio/Video Receiver that supports one
or more of the audio formats supported by your
player. Check the logos on the front of the Audio/
Video receiver and the manual. (PCM Stereo, PCM
Multi-Ch, Dolby Digital, Dolby Digital Plus, Dolby
TrueHD, DTS and/or DTS-HD)
The 1080p video output frame rate may
be automatically set to either 24 Hz or
50 Hz depending both on the capability
and preference of the connected TV and
based on the native video frame rate of the
content on the BD-ROM disc.
18 Connecting
Connecting to an Amplifier via
HDMI Output
Connect the player’s HDMI OUT jack to the
corresponding in jack on your amplifier using a
HDMI cable.
Connecting to an Amplifier via
Digital Audio Output
Connect the player’s DIGITAL AUDIO OUT jack
to the corresponding in jack (COAXIAL) on your
amplifier using an optional digital audio cable.
Rear of the unit
Rear of the unit
2
Coaxial cable
HDMI cable
Receiver/Amplifier
HDMI cable
Receiver/Amplifier
TV
You will need to activate the player’s digital output.
Connect the amplifier’s HDMI output jack to HDMI
input jack on your TV using a HDMI cable if your
amplifier has HDMI output jack.
You will need to activate the player’s digital output.
Connecting 19
Note
,
USB device connection
This player supports USB flash drive/external
HDD formatted in FAT16, FAT32 and NTFS
when accessing files (music, photo, movie).
However, for Blu-ray contents, only FAT16
and FAT32 formats are supported. Use the
USB flash drive/external HDD formatted in
either FAT16 or FAT32 when enjoying Blu-ray
contents.
y
This player can play movie, music and photo files
contained in the USB device.
Playback content in the USB
device
1. Insert a USB device to the USB port until it fits
into place.
This unit can support up to 4 partitions of
the USB device.
y
y
y
2
Do not extract the USB device during
operation (play, etc.).
A USB device which requires additional
program installation when you have
connected it to a computer, is not
supported.
USB device: USB device that supports
USB1.1 and USB2.0.
y
y
When you connect the USB device on the HOME
menu, the player plays a music file contained in the
USB storage device automatically. If the USB storage
device is containing various types of files, a menu
for the file type selection will appear.
Movie, music and photo files can be played.
For details of operations on each file, refer to
relevant pages.
Regular back up is recommended to
prevent data loss.
y
y
File loading may takes few minutes depending on
the number of content stored in the USB storage
device. Press ENTER (b) while [Cancel] is selected
to stop loading.
If you use a USB extension cable, USB HUB
or USB Multi-reader, the USB device may not
be recognized.
Some USB device may not work with this
unit.
y
y
y
2. Press HOME (n).
3. Select [Movie], [Photo] or [Music] using a/d,
Digital camera and mobile phone are not
supported.
and press ENTER (b).
4. Select the [USB] option using w/s, and press
USB Port of the unit cannot be connected
to PC. The unit cannot be used as a storage
device.
ENTER (b).
5. Select a file using w/s/a/d, and press PLAY
or ENTER (b) to play the file.
6. Withdraw the USB device carefully.
20 System Setting
Settings
Initial Setup
Adjust the Setup Settings
You can change the settings of the player in the
[Setup] menu.
1. Press HOME (n).
When you turn on the unit for the first time, the
initial setup wizard appears on the screen. Set the
display language on the initial setup wizard.
1. Press 1(POWER).
The initial setup wizard appears on the screen.
2. Use a/dto select the [Setup] and press ENTER
2. Use w/s/a/dto select a display language
(b). The [Setup] menu appears.
and press ENTER (b).
3
3. Use w/sto select the first setup option, and
3. Check the setting that you have set in the
previous step.
press dto move to the second level.
4. Use w/sto select a second setup option, and
Press ENTER (b) while [Finish] is highlighted
to finish the initial setup settings. If there is any
settings to be changed, use a/dto select
[Previous] and press ENTER (b).
press ENTER (b) to move to the third level.
5. Use w/sto select a desired setting, and press
ENTER (b) to confirm your selection.
System Setting 21
Resolution
[DISPLAY] Menu
Sets the output resolution of the HDMI video signal.
setting.
TV Aspect Ratio
Select a TV aspect ratio option according to your TV
type.
[Auto]
If the HDMI OUT jack is connected to
TVs providing display information (EDID),
automatically selects the resolution best suited
to the connected TV.
[4:3 Letter Box]
Select when a standard 4:3 TV is connected.
Displays theatrical images with masking bars
above and below the picture.
[1080p]
[4:3 Pan Scan]
Outputs 1080 lines of progressive video.
Select when a standard 4:3 TV is connected.
Displays pictures cropped to fill your TV screen.
Both sides of the picture are cut off.
[1080i]
Outputs 1080 lines of interlaced video.
3
[16:9 Original]
[720p]
Select when a 16:9 wide TV is connected. The
4:3 picture is displayed with an original 4:3
aspect ratio, with black bars appearing at the
left and right sides.
Outputs 720 lines of progressive video.
[576p]
Outputs 576 lines of progressive video.
[16:9 Full]
[576i]
Select when a 16:9 wide TV is connected. The
4:3 picture is adjusted horizontally (in a linear
proportion) to fill the entire screen.
Outputs 576 lines of interlaced video.
1080p Display Mode
Note
,
When the resolution is set to 1080p, select
[24 Hz] for smooth presentation of film material
(1080p/24 Hz) with a HDMI-equipped display
compatible with 1080p/24 Hz input.
You cannot select [4:3 Letter Box] and
[4:3 Pan Scan] option when the resolution is
set to higher than 720p.
Note
,
When you select [24 Hz], you may
experience some picture disturbance when
the video switches video and film material.
In this case, select [50 Hz].
y
y
Even when [1080p Display Mode] is set to
[24 Hz], if your TV is not compatible with
1080p/24 Hz, the actual frame frequency of
the video output will be 50 Hz to match the
video source format.
22 System Setting
HDMI Color Setting
Select the type of output from the HDMI OUT jack.
For this setting, please refer to the manuals of your
display device.
[LANGUAGE] Menu
Display Menu
Select a language for the [Setup] menu and on-
screen display.
[YCbCr]
Select when connecting to a HDMI display
device.
Disc Menu/Disc Audio/
Disc Subtitle
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
[RGB]
Select when connecting to a DVI display
device.
[Original]
Refers to the original language in which the
disc was recorded.
Home Menu Guide
This function allows you to display or delete the
guide bubble on the Home Menu. Set this option
to [On] for displaying guide.
3
[Other]
Press ENTER (b) to select another language.
Use number buttons then press ENTER (b)
to enter the corresponding 4-digit number
according to the language code list on page 40.
[Off] (Disc Subtitle only)
Turn off Subtitle.
Note
,
Depending on the disc, your language setting
may not work.
System Setting 23
Sampling Freq.
(Digital Audio Output)
[AUDIO] Menu
Each disc has a variety of audio output options. Set
the player’s Audio options according to the type of
audio system you use.
[192 kHz]
Select this if your A/V Receiver or Amplifier is
capable of handling 192 kHz signals.
Note
,
Since many factors affect the type of audio
output, see“Audio Output Specifications”on
page 43 for details.
[96 kHz]
Select this if your A/V Receiver or Amplifier is
not capable of handling 192 kHz signals. When
this choice is made, this unit
automatically converts any 192 kHz signals to
96 kHz so your system can decode them.
Digital Output
[PCM Stereo] (HDMI, COAXIAL)
[48 kHz]
Select if you connect this unit’s HDMI OUT or
DIGITAL AUDIO OUT jack to a device with two-
channel digital stereo decoder.
Select this if your A/V Receiver or Amplifier is
not capable of handling 192 kHz and 96 kHz
signal. When this choice is made, this unit
automatically converts any 192 kHz and 96 kHz
signals to 48 kHz so your system can decode
them.
3
[PCM Multi-Ch] (HDMI only)
Select if you connect this unit’s HDMI OUT jack
to a device with multi-channel digital decoder.
Check the documentation for your A/V Receiver or
Amplifier to verify its capabilities.
[DTS Re-Encode] (HDMI, COAXIAL)
Select if you connect this unit’s HDMI OUT or
DIGITAL AUDIO OUT jack to a device with DTS
decoder.
DRC (Dynamic Range Control)
This function allows you to listen to a movie at a
lower volume without losing clarity of sound.
[BitStream] (HDMI, COAXIAL)
Select if you connect this unit’s DIGITAL AUDIO
OUT and HDMI OUT jack to a device with
LPCM, Dolby Digital, Dolby Digital Plus, Dolby
TrueHD, DTS and DTS-HD decoder.
[Off]
Turns off this function.
[On]
Note
Compress the dynamic range of the Dolby
Digital, Dolby Digital Plus or Dolby TrueHD
audio output.
,
When [Digital Output] option is set to [PCM
Multi-Ch], the audio may output as PCM
Stereo if the PCM Multi-Ch information is
not detected from HDMI device with EDID.
y
y
[Auto]
The dynamic range of the Dolby TrueHD audio
output is specified by itself.
And the dynamic range of the Dolby Digital
and Dolby Digital Plus are operated as same as
the [On] mode.
If the [Digital Output] option is set to [DTS
Re-Encode], the DTS Re-Encode audio is
outputted for BD-ROM discs with secondary
audio and the original audio is outputted
for the other discs (like [BitStream]).
Note
,
The DRC setting can only be changed when
the unit is in“NO DISC”status or the unit is in
complete stop mode.
24 System Setting
DVD Rating
Blocks playback of rated DVD based on their
content. (Not all discs are rated.)
[LOCK] Menu
The [LOCK] settings affect only BD-ROM and DVD
playback.
To access the any features in [LOCK] settings, you
must enter the 4-digit security code you have
created.
If you have not entered a password yet, you are
prompted to do so. Enter a 4-digit password twice,
and press ENTER (b) to create a new password.
[Rating 1-8]
Rating one (1) has the most restrictions and
rating eight (8) is the least restrictive.
[Unlock]
If you select [Unlock], parental control is not
active and the disc plays in full.
Password
You can create or change the password.
Blu-ray Disc Rating
Set an age limit of BD-ROM play. Use number
[None]
buttons to input an age limit for BD-ROM viewing.
3
Enter a 4-digit password twice, and press
ENTER (b) to create a new password.
[255]
[Change]
All BD-ROM can be played.
Enter the current password and press ENTER
(b). Enter a 4-digit password twice, and press
ENTER (b) to create a new password.
[0-254]
Prohibits play of BD-ROM with corresponding
ratings recorded on them.
If you forget your password
Note
,
If you forget your password, you can clear it using
the following steps:
The [Blu-ray Disc Rating] will be applied
only for the Blu-ray disc that containing the
Advanced Rating Control.
y
1. Remove any disc that might be in the player.
2. Select [Password] option in the [Setup] menu.
3. Use Number buttons to enter“210499”. The
password is cleared.
Area Code
Enter the code of the area whose standards were
used to rate the DVD video disc, based on the list
Note
,
If you make a mistake before pressing ENTER
(b), press CLEAR. Then input the correct
password.
System Setting 25
Auto Power Off
[OTHERS] Menu
The screen saver appears when you leave the
player in Stop mode for about five minutes. If
you set this option to [On], the unit automatically
turns off within 20 minutes since the Screen Saver
is displayed. Set this option to [Off] to leave the
screen saver until the unit is operated by the user.
DivX® VOD
ABOUT DIVX VIDEO: DivX® is a digital video
format created by DivX, LLC, a subsidiary of Rovi
Corporation. This is an official DivX Certified® device
that plays DivX video. Visit divx.com for more
information and software tools to convert your files
into DivX videos.
Initialize
ABOUT DIVX VIDEO-ON-DEMAND: This DivX
Certified® device must be registered in order to play
purchased DivX Video-on-Demand (VOD) movies.
To obtain your registration code, locate the DivX
VOD section in your device setup menu. Go to vod.
divx.com for more information on how to complete
your registration.
[Factory Set]
You can reset the player to its original factory
settings.
[Blu-ray Storage Clear]
3
Initializes the Blu-ray contents from the
connected USB storage.
[Register]
Software
Displays the registration code of your player.
[Information]
[Deregister]
Displays the current software version.
Deactivate your player and display the
deactivation code.
Note
,
All the downloaded videos from DivX(R) VOD
with this player’s registration code can only be
played on this unit.
26 Operating
Playing a Disc
General Playback
Using [HOME] menu
erot
1. Press B(OPEN/CLOSE), and place a disc on the
disc tray.
The home menu appears when you press HOME
(n). Use a/dto select a category and press
ENTER (b).
2. Press B(OPEN/CLOSE) to close the disc tray.
For most Audio CD, BD-ROM and
DVD-ROM discs, playback starts automatically.
3. Press HOME (n).
4. Select [Movie] or [Music] using a/d, and press
ENTER (b).
5. Select [Blu-ray Disc], [DVD], [VR] or [Audio]
option using w/s, and press ENTER (b).
Note
,
Playback functions described in this manual
are not always available with every file and
media. Some functions can be restricted
depending on many factors.
y
y
Depending on the BD-ROM titles, a USB
device connection may be needed for the
proper playback.
4
a
b
c
d
[Movie] - Plays video contents.
[Photo] - Plays photo contents.
[Music] - Plays audio contents.
[Setup] - Adjusts the system settings.
Unfinalized DVD-VR format discs may not
be played in this player.
y
y
Some DVD-VR discs are made with CPRM
data by DVD RECORDER. This unit cannot
support these kinds of discs.
Playing a file on disc/USB
device
yui
This player can play movie, music and photo files
contained in the disc or USB device.
1. Insert a data disc on the tray or connect a USB
device.
2. Press HOME (n).
3. Select [Movie], [Photo] or [Music] using a/d,
and press ENTER (b).
4. Select [Data] or [USB] option using w/s, and
press ENTER (b).
5. Select a file using w/s/a/d, and press
d(PLAY) or ENTER (b) to play the file.
Operating 27
Basic operations for video and
audio content
Basic operations for photo
content
To stop playback
To play a slide show
Press Z(STOP) while playback.
Press z(PLAY) to start slide show.
To pause playback
To stop a slide show
Press M(PAUSE) while playback.
Press z(PLAY) to resume playback.
Press Z(STOP) while slide show.
To pause a slide show
Press M(PAUSE) while slide show.
To play frame-by-frame (Video)
Press M(PAUSE) while movie playback.
Press M(PAUSE) repeatedly to play Frame-by-Frame
playback.
Press z(PLAY) to re-start the slide show.
To skip to the next/previous photo
While viewing a photo in full screen, press aor d
to go to the previous or next photo.
To scan forward or backward
Press cor vto play fast forward or fast reverse
during playback.
Using the disc menu
You can change the various playback speeds by
4
pressing cor vrepeatedly.
ero
To slow down the playing speed
While the playback is paused, press vrepeatedly
to play various speeds of slow motion.
To display the disc menu
The menu screen may be displayed first after
loading a disc which contains a menu. If you want
to display the disc menu while playback, press DISC
MENU.
To skip to the next/previous
chapter/track/file
During playback, press Cor Vto go to the
next chapter/track/file or to return to the beginning
of the current chapter/track/file.
Use w/s/a/dbuttons to navigate through
menu items.
To display the Pop-up menu
Some BD-ROM discs contain Pop-up menu that
appears while playback.
Press Ctwice briefly to step back to the previous
chapter/track/file.
Press TITLE/POPUP while playback, and use w/s/
a/dbuttons to navigate through menu items.
28 Operating
Resume playback
Advanced Playback
eroyt
u
The unit records the point where you pressed the
Z(STOP) depending on the disc.
If“MZ(Resume Stop)”appears on the screen
briefly, press z(PLAY) to resume playback (from
the scene point).
If you press Z(STOP) twice or unload the disc,
“Z(Complete Stop)”appears on the screen. The unit
will clear the stopped point.
Repeat Playback
erotu
y
During playback, press REPEAT (h) repeatedly to
select a desired repeat mode.
Blu-ray Disc / DVD / Movie files
jA- – Selected portion will be repeated continually.
Note
,
jChapter – The current chapter will be played
back repeatedly.
The resume point may be cleared when a
button is pressed (for example; 1(POWER),
B(OPEN/CLOSE), etc).
y
jTitle – The current title will be played back
repeatedly.
On BD-ROM discs with BD-J, the resume
playback function does not work.
y
y
jAll – All the tracks or files will be played back
repeatedly.
If you press Z(STOP) once during BD-ROM
interactive title playback, the unit will be in
Complete Stop mode.
4
To return to normal playback, press REPEAT (h)
repeatedly to select [Off].
Audio CDs/Music files
;Track– The current track or file will be played
back repeatedly.
Last Scene Memory
er
:All – All the tracks or files will be played back
repeatedly.
This unit memorizes the last scene from the last disc
that is viewed. The last scene remains in memory
even if you remove the disc from the unit or switch
off the unit. If you load a disc that has the scene
memorized, the scene is automatically recalled.
l – The tracks or files will be played back in
random order.
l:All – All the tracks or files will be played
back repeatedly in random order.
Note
,
A-B – Selected portion will be repeated
continually. (Audio CD only)
k
Last Scene Memory function for a previous
disc is erased once a different disc is played.
y
y
y
y
To return to normal playback, press CLEAR.
This function may not work depending on
the disc.
Note
,
On BD-ROM discs with BD-J, the last scene
memory function does not work.
If you press Vonce during Repeat
Chapter/Track playback, the repeat playback
cancels.
y
y
This unit does not memorize settings of
a disc if you switch off the unit before
commencing to play it.
This function may not work on some disc or
title.
Operating 29
Repeating a specific portion
Changing content list view
erot
yui
This player can repeat a portion you have selected.
On the [Movie], [Music] or [Photo] menu, you can
change the content list view.
1. While playback, press REPEAT (h) to select
[A-] at the beginning of the portion you wish to
repeat.
Method 1
Press red (R) coloured button repeatedly.
2. Press ENTER (b) at the end of the portion. Your
selected portion will be repeated continually.
3. To return to normal playback, press REPEAT
(h) repeatedly to select [Off].
Note
,
You cannot select a portion less than 3
seconds.
y
y
This function may not work on some disc or
title.
4
Viewing content information
y
The player can display the content information.
1. Select a file using w/s/a/d.
2. Press INFO/MENU (m) to display the option
menu.
3. Select the [Information] option using w/s, and
press ENTER (b).
The file information appears on the screen.
While movie playback, you can display the file
information by pressing TITLE/POPUP.
Note
,
The information displayed on the screen
may not correct comparing actual content
information.
Method 2
1. On the content list, press INFO/MENU (m) to
display the option menu.
2. Use w/sto select the [View Change] option.
3. Press ENTER (b) to change the content list
view.
30 Operating
Selecting a subtitle file
Options while viewing a photo
y
i
If the subtitle file name is different from the movie
file name, you need to select the subtitle file on the
[Movie] menu before playing the movie.
You can use various options during viewing a
photo in full screen.
1. While viewing a photo in full screen, press INFO/
1. Use w/s/a/dto select the subtitle file you
MENU (m) to display the option menu.
wish to play in the [Movie] menu.
2. Select an option using w/s.
2. Press ENTER (b).
Press ENTER (b) again to deselect the subtitle
file. Selected subtitle file will be displayed when
you play the movie file.
a Current photo/Total number of photos
4
– Use a/dto view previous/next photo.
b Slide Show – Press ENTER (b) to start or
Note
,
pause slide show.
If you press Z(STOP) while playback, the
subtitle selection is cancelled.
c Music Select – Select the background
music for the slide show (page 31).
d Music –Press ENTER (b) to start or pause
background music.
e Rotate – Press ENTER (b) to rotate the
photo clockwise.
f Zoom – Press ENTER (b) to display the
[Zoom] menu.
g Effect – Use a/dto select a transition
effect between photos in a slide show.
h Speed – Use a/dto select a delaying
speed between photos in a slide show.
3. Press BACK (1) to exit the option menu.
Operating 31
Listening to music while slide
show
On-Screen display
You can display and adjust various information and
settings about the content.
i
You can display photo files while listening to music
files.
Displaying content information
on-screen
1. While viewing a photo in full screen, press INFO/
MENU (m) to display the option menu.
2. Use w/sto select [Music Select] option, and
press ENTER (b) to display the [Music Select]
menu.
eroy
1. While playback, press INFO/MENU (m) to show
various playback information.
3. Use w/sto select a device, and press ENTER
(b).
4. Use w/sto select a file or a folder you wish to
play.
4
Select gand press ENTER (b) to display the
upper directory.
5. Use dto select [OK], and press ENTER (b) to
a Title – current title number/total number of
complete music selection.
titles
b Chapter – current chapter number/total
number of chapters
c Time – elapsed playing time/total playback
time
d Audio – selected audio language or channel
e Subtitle – selected subtitle.
f Angle – selected angle/total number of
angles
g TV Aspect Ratio – selected TV aspect Ratio
h Picture Mode – selected picture mode
32 Operating
2. Select an option using w/s.
Playing from selected time
eroy
3. Use a/dto adjust the selected option value.
4. Press BACK (1) to exit the On-Screen display.
1. Press INFO/MENU (m) during playback. The
time search box shows the elapsed playing
time.
Note
,
If no button is pressed for a few seconds,
the on-screen display disappears.
y
y
y
y
2. Select the [Time] option and then input the
required start time in hours, minutes, and
seconds from left to right.
A title number cannot be selected on some
discs.
Available items may differ depending on
discs or titles.
For example, to find a scene at 2 hours, 10
minutes, and 20 seconds, enter“21020”.
If an interactive Blu-ray Disc is playing back,
some setting information is displayed on
the screen but prohibited to be changed.
Press a/dto skip the playback 60 seconds
forward or backward.
3. Press ENTER (b) to start playback from selected
time.
Note
,
This function may not work on some disc or
titles.
y
4
Selecting a subtitle language
eroy
1. During playback, press INFO/MENU (m) to
display the On-Screen display.
2. Use w/sto select the [Subtitle] option.
3. Use a/dto select desired subtitle language.
4. Press BACK (1) to exit the On-Screen display.
Note
,
Some discs allow you to change subtitle
selections only via the disc menu. If this is
the case, press TITLE/POPUP or DISC MENU
button and choose the appropriate subtitle
from the selections on the disc menu.
y
You can select the [Subtitle] option on the
On-Screen display directely by pressing
SUBTITLE (]) button.
y
Operating 33
Hearing a different audio
Changing the TV Aspect Ratio
eroy
eoy
You can change the TV aspect ratio setting while
playback.
1. During playback, press INFO/MENU (m) to
display the On-Screen display.
2. Use w/sto select the [Audio] option.
1. During playback, press INFO/MENU (m) to
display the On-Screen display.
3. Use a/dto select desired audio language,
audio track or audio channel.
2. Use w/sto select the [TV Aspect Ratio]
option.
Note
,
3. Use a/dto select desired option.
Some discs allow you to change audio
selections only via the disc menu. In this
case, press TITLE/POP-UP or DISC MENU
button and choose the appropriate audio
from the selections on the disc menu.
y
4. Press BACK (1) to exit the On-Screen display.
Note
,
Even if you change the value of the [TV Aspect
Ratio] option in On-Screen display, the [TV
Aspect Ratio] option in the [Setup] menu is
not changed.
Immediately after you have switched sound,
there may be a temporary discrepancy
between the display and actual sound.
y
y
y
On BD-ROM disc, the multi audio format
(5.1CH or 7.1CH) is displayed with [MultiCH]
in the on-screen display.
4
You can select the [Audio] option on the
On-Screen display directely by pressing
AUDIO ([) button.
Watching from a different
angle
er
If the disc contains scenes recorded at different
camera angles, you can change to a different
camera angle during playback.
1. During playback, press INFO/MENU (m) to
display the On-Screen display.
2. Use w/sto select the [Angle] option.
3. Use a/dto select desired angle.
4. Press BACK (1) to exit the On-Screen display.
34 Operating
Changing subtitle code page
Changing the Picture Mode
y
eroy
If the subtitle is displayed in broken letter, you can
change the subtitle code page to view the subtitle
file properly.
You can change the [Picture mode] option while
playback.
1. During playback, press INFO/MENU (m) to
1. During playback, press INFO/MENU (m) to
display the On-Screen display.
display the playback menu.
2. Use w/sto select the [Picture Mode] option.
3. Use a/dto select desired option.
2. Use w/sto select the [Code Page] option.
3. Use a/dto select desired code option.
4. Press BACK (1) to exit the On-Screen display.
Setting the [User setting] option
1. During playback, press INFO/MENU (m) to
display the On-Screen display.
2. Use w/sto select the [Picture Mode] option.
3. Use a/dto select the [User setting] option,
and press ENTER (b).
4
4. Press BACK (1) to exit the On-Screen display.
4. Use w/s/a/dto adjust the [Picture Mode]
options.
Select [Default] option then press ENTER (b) to
reset the all video adjustments.
5. Use w/s/a/dto select the [Close] option,
and press ENTER (b) to finish setting.
Operating 35
8. Use w/s/a/dto select [OK], and press
Audio CD recording
You can record one desired track or all of the tracks
in Audio CD to a USB storage device.
ENTER (b) to start Audio CD recording.
If you want to stop in progressing Audio CD
recording, press ENTER (b) while [Cancel] is
highlighted.
1. Insert a USB storage device to the USB port on
the front panel.
9. A message appears when Audio CD recording is
completed. Press ENTER (b) to check the audio
file created in the destination folder.
2. Press B(OPEN/CLOSE), and place an Audio CD
on the disc tray.
Note
,
Press B(OPEN/CLOSE) to close the disc tray.
The playback starts automatically.
The table below shows the average
recording time from an audio track with 4
minutes of playback time to an audio file
with 192 kbps as an example.
y
3. Press INFO/MENU (m) to display the option
menu.
4. Use w/sto select [CD Recording] option, and
stop mode
1 min.
while playback
4 min.
press ENTER (b).
5. Use w/sto select a track you wish to copy on
the menu, and press ENTER (b).
Recording times in the table above are
approximate.
y
y
Repeat this step to select tracks as many as you
can.
Actual recording time for USB storage
device varies depending on the USB storage
device’s ability.
4
Selects all the tracks on an
Audio CD.
Make sure that there is minimum of 50 MB
free space is needed when recording into
the USB storage device.
y
Selects an encoding option
from the pop-up menu
(128kbps, 192kbps or 320kbps).
The length of the audio should be longer
than 20 seconds for the proper recording.
y
y
Cancels the recording and
returns to the previous screen.
Do not turn off this player or extract the
connected USB storage device during Audio
CD recording.
6. Use w/s/a/dto select [Start], and press
ENTER (b).
7. Use w/s/a/dto select a destination folder
Caution
The recording or copying features on this
player are provided for your personal and
non-commercial use. The making of
>
to be copied.
unauthorized copies of copy-protected
material, including computer programs, files,
broadcasts and sound recordings, may be an
infringement of copyrights and constitute a
criminal offense. This equipment should not be
used for such purposes. LG expressly disclaims
any responsibility for illegal distribution or
use of unauthorized content in commercial
purpose.
If you want to create a new folder, use
w/s/a/dto select [New Folder] and press
ENTER (b).
Be Responsible
Enter a folder name using virtual keyboard, and
Respect Copyrights
press ENTER (b) while [OK] is selected.
36 Troubleshooting
Troubleshooting
General
Symptom
Cause & Solution
The Power does not turned on.
Plug the power cord into the wall outlet securely.
y
The unit does not start
playback.
Insert a playable disc. (Check the disc type, colour system, and
regional code.)
y
Place the disc with the playback side down.
Place the disc on the disc tray correctly inside the guide.
Clean the disc.
y
y
y
y
Cancel the Rating function or change the rating level.
The angle cannot be changed.
Multi-angles are not recorded on the DVD Video being played.
y
Cannot play movie, photo or
music files.
The files are not recorded in a format that the unit can play.
The unit does not support the codec of the movie file.
y
y
The remote control does not
work properly.
The remote control is not pointed at the remote sensor of the unit.
The remote control is too far from the unit.
y
y
y
y
There is an obstacle in the path of the remote control and the unit.
The battery in the remote control is exhausted.
5
The unit is plugged in, but the You can reset the unit as follows.
power will not turn on or off.
Unplug the power cord, wait at least five seconds, and then plug it in
y
again.
The unit is not operating
normally.
Troubleshooting 37
Picture
Symptom
Cause & Solution
There is no picture.
Select the appropriate video input mode on the TV so the picture
from the unit appears on the TV screen.
y
Connect the video connection securely.
y
y
Check the [HDMI Color Setting] in the [Setup] menu is set to the
appropriate item that conforms to your video connection.
Your TV may not support the resolution you have set on the player.
Change the resolution that your TV accepts.
y
y
The player’s HDMI OUT jack is connected to a DVI device that does
not support copyright protection.
Picture noise appears.
You are playing a disc recorded in a colour system that is different
from your TV.
y
y
Set the resolution which your TV accepts.
Customer Support
You can update the Player using the latest software to enhance the products operation and/or add new
features. To obtain the latest software for this player (if updates have been made), please visit
Open source software notice
To obtain the corresponding source code under GPL, LGPL and other open source licenses, please visit
available to download with the source code.
5
38 Appendix
Setting up the remote to
control your TV
Controlling a TV with
the Supplied Remote
Control
You can operate your TV with the supplied remote
control.
If your TV is listed in the table below, set the
appropriate manufacturer code.
You can control your TV using the buttons below.
1. While holding down 1(TV POWER) button,
and press the manufacturer code for your
TV with the numerical buttons (see the table
below).
Manufacturer
LG
Code Number
1(Default), 2
Zenith
1, 3, 4
1, 2
6, 7
8, 9
4
GoldStar
Samsung
Sony
By pressing
You can
1(TV POWER)
Turn the TV on or off.
Scan up or down through
memorized channels.
PR/CH +/–
VOL +/–
Hitachi
2. Release the 1(TV POWER) button to complete
Adjust the volume of the TV
setting.
Switch the TV’s input source
between the TV and other
input sources.
Depending on your TV, some or all buttons may not
function on the TV, even after entering the correct
manufacturer code. When you replace the batteries
of the remote, the code number you have set may
be reset to the default setting. Set the appropriate
code number again.
AV/INPUT
VOL +/–
Adjust the volume of the TV
Note
,
Depending on the unit being connected, you
may not be able to control your TV using some
of the buttons.
6
Appendix 39
Area Code List
Choose an area code from this list.
Area
Code Area
AF Fiji
Code Area
FJ Monaco
Code Area
Code
MC
MN
MA
NP
NL
AN
NZ
NG
NO
OM
PK
Singapore
Slovak Republic
SG
Afghanistan
Argentina
Australia
Austria
FI Mongolia
FR Morocco
DE Nepal
SK
SI
AR Finland
AU France
AT Germany
BE Great Britain
BT Greece
BO Greenland
BR Hong Kong
KH Hungary
CA India
Slovenia
South Africa
South Korea
Spain
ZA
KR
Belgium
Bhutan
GB Netherlands
GR Antilles
GL New Zealand
HK Nigeria
HU Norway
IN Oman
ES
Sri Lanka
Sweden
LK
Bolivia
SE
Brazil
Switzerland
Taiwan
CH
TW
TH
TR
Cambodia
Canada
Chile
ID Pakistan
IL Panama
Thailand
Turkey
CL Indonesia
CN Israel
China
PA
IT Paraguay
JM Philippines
JP Poland
PY
Uganda
UG
UA
US
UY
UZ
VN
ZW
Colombia
Congo
CO Italy
PH
PL
Ukraine
CG Jamaica
CR Japan
United States
Uruguay
Uzbekistan
Vietnam
Costa Rica
Croatia
HR Kenya
KE Portugal
KW Romania
LY Russian
PT
Czech Republic
Denmark
Ecuador
Egypt
CZ Kuwait
DK Libya
RO
Federation
RU
SA
SN
LU
Zimbabwe
EC Luxembourg
EG Malaysia
SV Maldives
ET Mexico
Saudi Arabia
MY
Senegal
6
El Salvador
Ethiopia
MV
MX
40 Appendix
Language code List
Use this list to input your desired language for the following initial settings: [Disc Audio],
[Disc Subtitle] and [Disc Menu].
Language
Afar
Code Language
6565 French
6570 Frisian
Code Language
7082 Lithuanian
7089 Macedonian
7176 Malagasy
7565 Malay
Code Language
7684 Sindhi
7775 Singhalese
7771 Slovak
7783 Slovenian
7776 Spanish
7773 Sudanese
7782 Swahili
7779 Swedish
7778 Tagalog
7865 Tajik
Code
8368
8373
8375
8376
6983
8385
8387
8386
8476
8471
8465
8469
8472
8479
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
Afrikaans
Albanian
Amharic
Arabic
8381 Galician
6577 Georgian
6582 German
7289 Greek
6869 Malayalam
6976 Maori
Armenian
Assamese
Aymara
6583 Greenlandic
6588 Guarani
6590 Gujarati
6665 Hausa
7576 Marathi
7178 Moldavian
7185 Mongolian
7265 Nauru
Azerbaijani
Bashkir
Basque
6985 Hebrew
6678 Hindi
7387 Nepali
7869 Tamil
Bengali; Bangla
Bhutani
Bihari
7273 Norwegian
7285 Oriya
7879 Telugu
7982 Thai
6890 Hungarian
6672 Icelandic
6682 Indonesian
6671 Interlingua
7789 Irish
7383 Panjabi
8065 Tonga
8083 Turkish
7065 Turkmen
8076 Twi
Breton
7378 Pashto, Pushto
7365 Persian
Bulgarian
Burmese
Byelorussian
Chinese
Croatian
Czech
7165 Polish
6669 Italian
7384 Portuguese
7465 Quechua
8084 Ukrainian
8185 Urdu
9072 Japanese
7282 Kannada
6783 Kashmiri
6865 Kazakh
7876 Kirghiz
7578 Rhaeto-Romance 8277 Uzbek
6
7583 Rumanian
7575 Russian
7589 Samoan
7579 Sanskrit
7585 Scots Gaelic
7679 Serbian
7665 Serbo-Croatian
7686 Shona
8279 Vietnamese
Danish
8285 Volapük
8377 Welsh
8365 Wolof
7168 Xhosa
8382 Yiddish
8372 Yoruba
8378 Zulu
Dutch
Korean
English
6978
6979
6984
7079
7074
7073
Kurdish
Laotian
Esperanto
Estonian
Faroese
Fiji
Latin
Latvian, Lettish
Lingala
7678
Finnish
Appendix 41
Trademarks and
Licenses
Manufactured under license under U.S. Patent
Nos: 5,956,674; 5,974,380; 6,487,535 & other U.S.
and worldwide patents issued & pending. DTS,
the Symbol, & DTS and the Symbol together are
registered trademarks & DTS 2.0+Digital Out is a
trademark of DTS, Inc. Product includes software.
© DTS, Inc. All Rights Reserved.
Blu-ray Disc™, Blu-ray™, BONUSVIEW™ and
the logos are trademarks of the Blu-ray Disc
Association.
“AVCHD”and the“AVCHD”logo are trademarks of
Panasonic Corporation and Sony Corporation.
“DVD Logo”is a trademark of DVD Format/Logo
Licensing Corporation.
DivX®, DivX Certified® and associated logos are
trademarks of Rovi Corporation or its subsidiaries
and are used under license.
Java is a trademark of Oracle and/or its affiliates.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC in the United
States and other countries.
6
“x.v.Colour”is a trademark of Sony Corporation.
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
42 Appendix
Cinavia Notice
This product uses Cinavia technology to limit the
use of unauthorized copies of some commercially-
produced film and videos and their soundtracks.
When a prohibited use of an unauthorized copy is
detected, a message will be displayed and playback
or copying will be interrupted.
More information about Cinavia technology
is provided at the Cinavia Online Consumer
request additional information about Cinavia by
mail, send a postcard with your mailing address
to: Cinavia Consumer Information Center, P.O. Box
86851, San Diego, CA, 92138, USA.
This product incorporates proprietary technology
under license from Verance Corporation and is
protected by U.S. Patent 7,369,677 and other U.S.
and worldwide patents issued and pending as well
as copyright and trade secret protection for certain
aspects of such technology. Cinavia is a trademark
of Verance Corporation. Copyright 2004-2010
Verance Corporation. All rights reserved by Verance.
Reverse engineering or disassembly is prohibited.
6
Appendix 43
Audio Output Specifications
3
Jack/Setting
COAXIAL (DIGITAL AUDIO OUT)
*
Source
4
BitStream
PCM Stereo
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
DTS Re-encode
*
Dolby Digital
Dolby Digital Plus
Dolby TrueHD
DTS
DTS
DTS
DTS
DTS
DTS
DTS
DTS
DTS
Dolby Digital
Dolby Digital
Dolby Digital
DTS
DTS-HD
DTS
Linear PCM 2ch
Linear PCM 5.1ch
Linear PCM 7.1ch
PCM 2ch
PCM 2ch
PCM 2ch
Jack/Setting
Source
HDMI OUT
4
1
2
BitStream
* *
PCM Stereo
PCM Multi-Ch
PCM 2ch
DTS Re-encode
*
Dolby Digital
Dolby Digital Plus
Dolby TrueHD
DTS
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
DTS
DTS
DTS
DTS
DTS
DTS
DTS
DTS
Dolby Digital
PCM 2ch
Dolby Digital Plus
Dolby TrueHD
DTS
PCM 2ch
PCM 2ch
DTS-HD
PCM 2ch
DTS-HD
Linear PCM 2ch
Linear PCM 5.1ch
Linear PCM 7.1ch
PCM 2ch
Linear PCM 2ch
Linear PCM 5.1ch
Linear PCM 7.1ch
PCM 5.1ch
PCM 7.1ch
6
*1 The secondary and interactive audio may not
be included in the output bitstream if [Digital
Output] option is set to [BitStream]. (Except
LPCM Codec : the output always include
interactive and secondary audio.)
*4 If the [Digital Output] option is set to [DTS re-
encode], the audio output is limited to 48 kHz
and 5.1Ch. If the [Digital Output] option is set
to [DTS re-encode], the DTS Re-encode audio
is outputted for BD-ROM discs, and the original
audio is outputted for the other discs (like
[BitStream]).
*2 This player automatically selects the HDMI audio
according to the decoding capability of the
connected HDMI device even though [Digital
Output] option is set to [BitStream].
If the HDMI OUT jack is connected to your TV
with High Speed HDMI™ Cable and Dolby Digital
Plus/Dolby TrueHD is outputted from HDMI OUT
jack, DIGITAL AUDIO OUT jack is limited to“PCM
2ch”(When the HDMI and DIGITAL AUDIO OUT
are connected simultaneously).
y
*3 On the PCM audio output, the sampling
frequency of DIGITAL AUDIO OUT is limited to
96 kHz.
44 Appendix
The audio is outputted as PCM 48 kHz/16 bit for
MP3/WMA file and PCM 44.1kHz/16 bit for Audio
CD while playback.
y
y
You must select a digital audio output and
a maximum sampling frequency that your
Amplifier (or AV receiver) accepts using [Digital
Output] and [Sampling Freq.] options on the
With digital audio connection (DIGITAL AUDIO
OUT or HDMI OUT), Disc Menu button sounds of
BD-ROM may not be heard if the [Digital Output]
option is set to [BitStream].
y
y
y
If the audio format of the digital output does
not match the capabilities of your receiver, the
receiver will produce a strong, distorted sound
or no sound at all.
Multi-channel Digital Surround Sound via digital
connection can only be obtained if your receiver
is equipped with a Digital Multi-channel decoder.
6
Appendix 45
Specifications
General
Power requirements
Power consumption
Dimensions (W x H x D)
Net Weight (Approx.)
Operating temperature
Operating humidity
Refer to main label on the rear panel.
12 W
Approx. 360 x 41 x 190 mm
1.3 Kg
5 °C to 35 °C
5 % to 90 %
Outputs
HDMI OUT (video/audio)
19 pin (Type A, HDMI™ Connector)
0.5 V (p-p), 75 Ω, RCA jack x 1
DIGITAL AUDIO OUT (COAXIAL)
System
Laser
Semiconductor laser
wavelength
405 nm / 650 nm
Signal system
Standard PAL/NTSC colour TV system
20 Hz to 20 kHz (48 kHz, 96 kHz, 192 kHz sampling)
Less than 0.02 %
Frequency response
Harmonic distortion
Dynamic range
Bus Power Supply (USB)
More than 95 dB
DC 5 V 0500 mA
Design and specifications are subject to change without notice.
y
6
46 Appendix
Notes on Discs
Maintenance
Handling Discs
Do not touch the playback side of the disc. Hold
the disc by the edges so that fingerprints do not
get on the surface. Never stick paper or tape on the
disc.
Handling the Unit
When shipping the unit
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
Storing Discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
Cleaning Discs
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the centre to out.
Keeping the exterior surfaces clean
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available cleaners,
or anti-static spray intended for older vinyl records.
Do not use volatile liquids such as insecticide
spray near the unit.
y
y
y
Wiping with strong pressure may damage the
surface.
Do not leave rubber or plastic products in
contact with the unit for a long period of time.
Maintaining the Unit
The unit is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty
or worn, the picture quality could be diminished.
For details, please contact your nearest authorized
service centre.
6
|