Kicker SOLO BARIC S10L7 User Manual

S15L7, S12L7, S10L7, S8L7  
Congratulations! You have just purchased one of the most advanced subwoofers in the history of car audio. Your KICKER Solo-Baric is  
the latest in KICKER’s trend-setting Solo-Baric line, designed and engineered to deliver the ultimate in low bass performance and  
unmatched durability when installed in a properly designed system. Thanks for buying KICKER. Enjoy.  
Solo-Baric Features  
Cast Aluminum Basket (patent pending) for strength and to reject stray magnetic fields  
Perimeter Venting in basket for continuous voice coil cooling and highly linear response  
Highly Rigid Cone (patent pending) with high internal damping and excellent resistance to sunlight, pollution, and moisture  
Inverted Structural Dome™ further increases cone’s resistance to flex under pressure  
Stitched Surround (patent pending) prevents cone/surround separation at high excursions  
Blackened Motor Parts for superior heat dissipation and long life  
Dual Ultra-Length Voice Coils for high excursion and flexible wiring options  
High-Temp Kapton Voice Coil Former prevents cone meltdown to minimize warping and rubbing  
One piece UniPlate™ pole piece and back plate:  
Blackened Pole Piece provides effective heat transfer and cool operation for maximum power handling  
One-Piece Hyper-Extended Pole reduces non-linear magnetic fields around the voice coil gap for even more heat sinking and  
excellent cone motion control  
Vented Pole Piece releases pressure under dustcap for freer cone motion and enhanced low bass  
Sleeved High-Power Tinsel Lead Wires to resist lead breakage and power-robbing resistance losses  
Spring-Loaded Nickel Plated Terminals for solid connections with large gauge speaker wire  
Rubatex front and rear gaskets for airtight seal  
Specifications  
Model  
Max amp power  
(watts)  
Sensitivity  
(dB 1w/1m)  
Voice Coil  
(in.)  
Fs  
(Hz)  
Vas  
(cu.ft)  
Qts  
Xmax Mounting Cutout Outer flange  
Mounting depth  
(in.)  
(in.)  
.60  
.50  
.50  
.41  
(in.)  
(in.)  
S15L7  
S12L7  
S10L7  
S8L7  
1000  
750  
600  
450  
90.2  
89.1  
87.3  
84.5  
2.5  
2.0  
2.0  
2.0  
23.0  
29.7  
35.1  
43.5  
9.9  
3.1  
1.2  
.46  
.477  
.419  
.410  
.551  
14.1 x 14.1  
11.2 x 11.2  
9.5 x 9.5  
7.6 x 7.6  
15.6 x 15.6  
12.54 x 12.54  
10.66 x 10.66  
8.8 x 8.8  
7.83  
7.00  
6.25  
4.63  
Based on measurements of Dual 2 Ohm models  
Important Break-In Information  
Every Solo-Baric L7 subwoofer is individually computer-tested before shipment to insure the highest performance standards possible.  
Like many precision machines, the Solo-Baric L7 requires a break-in period before it will reach optimum performance.  
When brand new, the L7-series high performance suspension system is very stiff. After approximately two weeks of daily usage, the suspen-  
sion will loosen, or break-in, to a point of equilibrium. This time period may vary depending on the amount of play time, volume level, and type  
of music you listen to. More play time, with medium volume levels and more bass content, will break in the subwoofer most quickly.  
For those of you with more sophisticated audio equipment, the Solo-Barics can be broken-in on the test bench overnight with the following  
procedure.  
Solo-Baric Freeair Break-In Procedure  
1. Connect the speaker to a power amp of about fifty watts or more. The speaker should not be mounted in any enclosure - just freeair.  
2. Connect an audio generator to the input of the power amp, and adjust the generator to approximatley 45Hz for the S8L7, 35Hz for the  
S10L7, 30Hz for the S12L7, and 20Hz for the S15L7.  
3. Now adjust the gain on the amplifier and generator so that the cone is moving to Xmax. This can be determined visually by looking at the  
"blur depth" of the logo on the dustcap. A close approximation will do. On the S8L7 this will be about 3/4", on the S10L7 about 1", on the  
S12L7 about 1", and on the S15L7 about 1 1/4".  
4. Operate the speakers in this manner for about eight hours. A quick break-in will give acceptable results in four hours, and a very thorough  
break-in would be closer to 16 hours.  
NOTE: Keep in mind that as the speaker is used under normal conditions the break-in will continue, so if you don't have time for the complete  
break-in period the speaker will still break-in itself under normal usage.  
Recommended Enclosures  
Solo-Baric L7-Series Sealed Enclosure Applications  
The Kicker Solo-Baric L7 woofers are obviously different than any woofer you have ever seen. Designed to give more output than an equiva-  
lent round speaker, the L7 is amazing when used in the recommended sealed boxes. These sealed enclosure SQ recommendations will give the  
smoothest response with the most energy at really low frequencies, around 20 to 30 Hz.  
The recommended Compact sealed boxes are in line with our traditional Solo-Baric enclosures. They have the highest power handling capabil-  
ity of all our recommended enclosure designs. They deliver massive amounts of high impact bass and can be driven with punishing levels of  
amplifier power.  
One of the benefits of the L7-series high performance suspension system is that the new Solo-Barics can operate in larger sealed enclosures  
for ultra sound quality (SQ) applications without significantly sacrificing their power handling. This extra bass extension and smoothness can be  
obtained by simply using a larger sealed enclosure. The box can be "sized up" all the way to a .707 Qtc enclosure, which has a very flat response,  
with greatly extended sub bass.  
Solo-Baric L7 series woofers also perform well in any sealed enclosure between the Compact and SQ sizes. These systems will exhibit some  
benefits of both (high impact and low extension) generally sounding more like the box to which they are most closely sized.  
These enclosure volume recommendations are for the airspace inside the enclosure and include the displacement of the woofer. Do not  
make the airspace any greater than recommended.  
Recommended Sealed Enclosures – Moderate Efficiency  
Solo-Baric Model  
Compact (minimum enclosure volume)  
.33 cu.ft. Power Handling = 450W  
.66 cu.ft. Power Handling = 600W  
.88 cu.ft. Power Handling = 750W  
1.5 cu.ft. Power Handling = 1000W  
SQ (.707 alignment) (maximum enclosure volume)  
S8L7  
.75 cu.ft. Power Handling =450W  
S10L7  
S12L7  
S15L7  
1.0 cu.ft. Power Handling = 600W  
2.0 cu.ft. Power Handling = 750W  
6.0 cu.ft. Power Handling = 1000W  
The following shows examples of the minimum enclosure sizes for each of the Solo-Baric L7s. Panel dimensions assume 3/4" wood thickness.  
Panel dimensions for minimum recommended enclosures:  
Model  
S8L7  
S10L7  
S12L7  
S15L7  
Volume (cu.ft.)  
Panel A  
Panel B  
10"x8"  
12"x10.5"  
13"x11.5"  
16.5"x11.5"  
Panel C  
8"X8.5"  
10.5"x10.5"  
11.5"x11.5"  
15"x11.5"  
0.33  
0.66  
0.88  
1.5  
10"x10"  
12"x12"  
13"x13"  
16.5"x16.5"  
NOTE: All sealed boxes should be 50% filled with loose polyfil. Allow about two weeks break-in time for the Solo-Barics to reach optimum low  
bass performance.  
Solo-Baric L7-Series Ported/Vented Enclosure Applications  
Ported Solo-Barics? Absolutely ... and with a vengeance! This is totally new for Solo-Barics, and it is very exciting! The new enclosures incorpo-  
rate massive slot loaded ports with ultra low air velocity for concussive street bass that will make your hair stand on end (if you have any left)!  
These are the type of boxes that are rapidly becoming the "enclosure of choice" for outrageous street bass and high performance SPL con-  
tests.  
The following chart shows three recommended ported enclosures for each Solo-Baric driver.  
Compact has increased bass efficiency over a sealed enclosure, yet can still fit in tighter applications. It is the smallest design that will work well  
for each woofer. Although it is the smallest ported enclosure the output from 30 to 80 Hz will be considerably higher than that of a sealed box.  
This smallest vented design is for places where you can only give up the room normally taken up by two L7s in the normal small sealed boxes.  
The two other ported designs have proportionately more output in this region.  
SPL is a medium sized enclosure that will kick out bass that can be heard for blocks away. And it does go LOW!  
Finally, SPL / Deep Bass is a large enclosure that has it all. It is high efficiency and will deliver the output needed to win SPL contests, yet low fre-  
quencies go all the way down to the basement - with power that will shake the  
foundations! We’re talking truly awesome.  
If space is not at a premium and you want to get the most from your Solo-Baric L7, try one of these designs. You won’t be disappointed.  
Recommended Ported Enclosures – High Efficiency  
Solo-Baric Model  
Compact  
SPL  
SPL / Deep Bass  
S8L7  
.66 cu.ft. + port;  
.8 cu.ft. + port;  
1.0 cu.ft. + port;  
1.5x9.5" port, 19.25" long  
Power Handling = 300W  
1.75x9.5" port, 19.75" long  
Power Handling = 325W  
2x9.5" port, 21.25" long  
Power Handling = 325W  
S10L7  
S12L7  
S15L7  
1.25 cu.ft. + port;  
2.5x11.25" port, 19.75" long  
Power Handling = 500W  
1.75 cu.ft. + port;  
2.75x11.25", port 17.75" long  
Power Handling = 525W  
2.25 cu.ft. +port;  
3x11.25" port, 18" long  
Power Handling = 550W  
1.75 cu.ft. + port;  
2.5x13.25" port, 22.5" long  
Power Handling = 750W  
2.5 cu.ft. + port;  
2.5x13.25" port, 16.5" long  
Power Handling = 750W  
3.25 cu.ft. + port;  
3x13.25" port, 14.5" long  
Power Handling = 750W  
3.0 cu.ft. + port;  
4.5 cu.ft. + port;  
6.0 cu.ft. + port;  
2.5x16.25" port, 19.5" long  
Power Handling = 1000W  
3x16.25" port, 14.75" long  
Power Handling = 1000W  
3.5X16.25"port, 13.75"long  
Power Handling =1000W  
NOTE: The use of a subsonic filter (such as a Kicker SWX - without chips & set to highpass) will significantly increase the power handling. The  
power handling specifications listed in the chart above include the use of a 25 Hz, 24dB/octave subsonic filter.  
Recommended Ported SPL Enclosure for S8L7  
Recommended Ported SPL Enclosure for S10L7  
Recommended Ported SPL Enclosure for S12L7  
Recommended Ported SPL Enclosure for S15L7  
SPEAKER SYSTEMS LIMITED WARRANTY  
Stillwater Designs warrants this product to be free from defects in material and workmanship under normal use for a period  
of one (1) year from date of original purchase, unless this product is labeled “B Stock”, in which case it is warranted for  
ninety (90) days from date of purchase. Should service be necessary under this warranty for any reason due to manufacturing  
defect or malfunction during the warranty period, Stillwater Designs will replace or repair (at its discretion) the defective mer-  
chandise with equivalent merchandise at no charge. Warranty replacements on “B-Stock” may have cosmetic scratches and  
blemishes. Discontinued products may be replaced with equivalent products.  
This warranty is valid only for the original purchaser and is not extended to owners of the product subsequent to the  
original purchaser. Any applicable implied warranties are limited in duration to a period of the express warranty as provided  
herein beginning with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to  
this product thereafter. Some states do not allow limitations on implied warranties, therefore these exclusions may not apply to  
you.  
This warranty gives you specific legal rights; however you may have other rights that vary from state to state.  
WHAT TO DO IF YOU NEED WARRANTY OR SERVICE  
Defective merchandise must be returned to your local Authorized Stillwater Designs (Kicker/Impulse) Dealer for warranty.  
Assistance in locating an Authorized Dealer can be obtained by writing or calling Stillwater Designs direct. You can confirm that a  
dealer is authorized by asking to see a current authorized dealer window decal.  
If it becomes necessary for you to return defective merchandise, call the Kicker Customer Service Department at (405)624-  
8510 for a Return Authorization (RA) number. Package all defective items in the original container or in a package that will pre-  
vent shipping damage, and return to  
Stillwater Designs, 5021 North Perkins Road, Stillwater, OK 74075  
The RA number must be clearly marked on the outside of the package. Return only defective components. Return of entire  
cabinets, system packs, pairs, etc. increases your return freight charges. Non-defective items received will be returned freight  
collect.  
Include a dated proof-of-purchase from an Authorized Dealer. Warranty expiration on items returned without proof-of-  
purchase will be determined from the manufacturing date code. Coverage may be invalidated if this date is greater than one (1)  
year previous to the date item is sent in. Freight must be prepaid; items received freight collect will be refused.  
Failure to follow these steps may void your warranty. Any questions can be directed to the Kicker Customer Service  
Department at (405)624-8510.  
WHAT IS NOT COVERED?  
This warranty is valid only if the product is used for the purpose for which it was designed.  
It does not cover:  
• Install slips (screwdriver holes)  
• Damage caused by exposure to water  
and/or excessive heat.  
• Items previously repaired by any  
unauthorized repair facility.  
• Items returned from unauthorized  
individuals or dealers.  
• Damage through negligence, misuse, or  
accident.  
• Return shipping on non-defective items.  
• Speakers damaged due to amplifier  
clipping or distortion.  
• Speakers with silicon caulk used for gasket  
material.  
• Items physically damaged due to abuse.  
• Freight damage.  
• The cost of shipping product to Stillwater  
Designs Service.  
HOW LONG WILL IT TAKE?  
Stillwater Designs maintains a goal of 24-hour service for all returns. Delays may be incurred if lack of replacement inventory  
or parts is encountered.  
INTERNATIONAL WARRANTY  
Contact your International Stillwater Designs dealer or distributor concerning specific  
procedures for your country’s warranty policies.  
P.O. Box 459 • Stillwater, Oklahoma 74076 • U.S.A. • 405 624-8510  
KICKER drivers are capable of producing sound levels that can permanently  
damage your hearing! Turning up a system to a level that has audible distortion is more damag-  
ing to your ears than listening to an undistorted system at the same volume level. The thresh-  
old of pain is always an indicator that the sound level is too loud and may permanently damage  
WARNING:  
your hearing.  
Please use common sense when controlling volume!  
January 2001  

Raypak 42 66 User Manual
POSIFLEX Business Machines CR 4000 User Manual
Plantronics Bluetooth Headset MX500c User Manual
Panasonic NV GS120GN User Manual
Panasonic DMW GWC1GU User Manual
MB QUART Quart Mobil PSC 216 User Manual
JVC R D S KD S731R User Manual
JVC MARINE CASE GR DVX8 User Manual
JVC LYT2043 001C M User Manual
JVC KD HDR1 User Manual