CD-RECEIVER
KDC-W4534
KDC-W4034A/G/AY/GY
KDC-W434A/G/GY
KDC-W410A/G/AY/GY
KDC-W40G
KDC-3034A/G
INSTRUCTION MANUAL
© B64-3294-00/00 (EW/EN/E2W/E2N)
Safety precautions
About CD players/disc changers
connected to this unit
Kenwood disc changers/ CD players released in
1998 or later can be connected to this unit.
Refer to the catalog or consult your Kenwood
dealer for connectable models of disc changers/
CD players.
2WARNING
To prevent injury or fire, take the
following precautions:
• To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools)
inside the unit.
Note that any Kenwood disc changers/ CD players
released in 1997 or earlier and disc changers made
by other makers cannot be connected to this unit.
Connecting unsupported disc changers/CD players
to this unit may result in damage.
Set the "O-N" Switch to the "N" position for the
applicable Kenwood disc changers/ CD players.
The functions you can use and the information
that can be displayed may differ depending on the
models being connected.
• Mounting and wiring this product requires
skills and experience. For safety’s sake, leave the
mounting and wiring work to professionals.
2CAUTION
To prevent damage to the machine, take
the following precautions:
• Make sure to ground the unit to a negative 12V
DC power supply.
• Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of
water splashing.
•
You can damage both your unit and the CD changer if
you connect them incorrectly.
• Do not place the faceplate (and the faceplate
case) in areas exposed to direct sunlight, excessive
heat or humidity. Also avoid places with too much
dust or the possibility of water splashing.
• To prevent deterioration, do not touch the
terminals of the unit or faceplate with your
fingers.
Lens Fogging
When you turn on the car heater in cold weather,
dew or condensation may form on the lens in the
CD player of the unit. Called lens fogging, this
condesnation on the lens may not allow CDs to
play. In such a situation, remove the disc and wait
for the condensation to evaporate. If the unit still
does not operate normally after a while, consult
your Kenwood dealer.
• Do not subject the faceplate to excessive shock,
as it is a piece of precision equipment.
• When replacing a fuse, only use a new fuse with
the prescribed rating. Using a fuse with the wrong
rating may cause your unit to malfunction.
• Do not use your own screws. Use only the screws
provided. If you use the wrong screws, you could
damage the unit.
Do Not Load 8 cm (3 in.) CDs in the CD
slot
If you try to load a 8 cm (3 in.) CD with its adapter
into the unit, the adapter might separate from the
CD and damage the unit.
|
English
3
Notes
• If you experience problems during installation,
consult your Kenwood dealer.
• When you purchase optional accessories, check
with your Kenwood dealer to make sure that they
work with your model and in your area.
Before using this unit for the first time
This unit is initially set on the Demonstration mode.
When using this unit for the first time, cancel the
<Demonstration mode Setting> (page 25).
• If the unit fails to operate properly, press the Reset
button. The unit returns to factory settings when
the Reset button is pressed.
• Press the reset button if the disc auto changer fails
to operate correctly. Normal operation should be
restored.
About DAB Tuner control
(KDC-W4534)
Refer to A group on the Instruction manual of DAB
Tuner KTC-9090DAB (optional accessory) for the
control method of DAB Tuner function.
However, the following control methods of the
function for this unit may be differed from the
Instruction manual; therefore, refer to the following
supplemental instruction.
<Auto Ensemble Memory Entry>
1. Select the preset band for Auto Ensemble
Memory Entry.
2. Press the [AME] button for at least 2 seconds.
Open Auto Ensemble Memory Entry.
After storing in the memory finishes, the
number of the pre-set buttons and the
ensemble label are displayed.
<Searching by programme type and language>
and <Languages to be displayed> in
<Programme Type (PTY) Function>
At the operation to press [DISP] button, use [TI]
button instead.
Reset button
• The characters which can be displayed by this
unit are A-Z 0-9 @ " ‘ ` % & * + – = , . / \ < > [ ] ( ) : ;
^ - { } | ~ .
• The RDS feature won’t work where the service is
not supported by any broadcasting station.
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.
Cleaning the Unit
If the faceplate of this unit is stained, wipe it with a
dry soft cloth such as a silicon cloth.
If the faceplate is stained badly, wipe the stain off
with a cloth moistened with neutral cleaner, then
wipe it again with a clean soft dry cloth.
•
Applying spray cleaner directly to the unit may affect its
mechanical parts. Wiping the faceplate with a hard cloth
or using a volatile liquid such as thinner or alcohol may
scratch the surface or erases characters.
Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get dirty,
wipe them with a clean soft dry cloth.
|
4
English
This Product is not installed by the manufacturer
of a vehicle on the production line, nor by the
professional importer of a vehicle into an EU
Member State.
Information on Disposal of Old Electrical
and Electronic Equipment (applicable for
EU countries that have adopted separate
waste collection systems)
Products with the symbol (crossed-out
wheeled bin) cannot be disposed as
household waste.
Old electrical and electronic equipment
should be recycled at a facility capable
of handling these items and their
waste byproducts. Contact your local
authority for details in locating a
recycle facility nearest to you. Proper
recycling and waste disposal will help
conserve resources whilst preventing
detrimental effects on our health and the
environment.
The marking of products using lasers
(Except for some areas)
The label is attached to the chassis/case and says
that the component uses laser beams that have
been classified as Class 1. It means that the unit
is utilizing laser beams that are of a weaker class.
There is no danger of hazardous radiation outside
the unit.
|
English
5
About MP3 and WMA
The playable MP3/WMA file (hereafter called
Audio file) and the media format has the following
limitation. The Audio file, which is not comforming
to the specification, may not play normally, or the
file and folder names may not display correctly.
The maximum number of characters for
display
File/Folder name: 64 (Joliet: 32) characters
MP3 ID3 Tag/ WMA Contents property: 30
characters
Playable Audio file
•
MP3, WMA: KDC-W4534/W4034A/W4034AY/
W4034G/W4034GY/W434A/W434G/
W410A/W410AY/W410G/W410GY/
W40G/W434GY
•
•
File/Folder name is the number of the characters
including the extensions.
MP3 ID3 Tag can only display the tag of Ver1.0/1.1.
Limitation of structure for the file and the
folder
•
•
Attach the correct extension for the Audio file (MP3:
".MP3", WMA: ".WMA")
Do not attach the extensions to files other than the
Audio file. If the extension is attached, the file, which is
not the Audio file, will play and outputs a loud noise,
causing damage to the speaker.
The files with copy protection cannot be played.
The settings of your encoding software and the
environment in which it is used may now allow you
to play or view specific audio files. For encoding
specifications and instructions on how to set encoding
software, browse through software help or check with
the developers.
• Maximum number of directory levels: 8
• Maximum number of folders: 100
• Maximum number of files per folder: 255
Playing order of the Audio file
The Audio file plays in the order which is written by
writing software. You may be able to set the playing
order by writing the play sequence numbers such
as "01" to "99" at the beginning of the file name.
•
•
Example
0
¡
: Folder
: Audio file
CD
(1)
¡!
2
Playable MP3 file
• MPEG 1/2 Audio Layer 3 file
• Transfer bit rate: 8-320 kbps
• Sampling frequency
¡"
3
¡#
¡$
: 8, 11.025, 12, 16, 22.05, 24, 32, 44.1, 48 kHz
Playable WMA file
4
• The file in accordance with Windows Media Audio
(Except for the file for Windows Media Player 9 or
after which applies the new functions)
¡%
• Playing order
Playing order after ¡! play.
• Transfer bit rate: 48-192 kbps
➡ ¡", ¡#, ¡$, ¡%...
• Sampling frequency: 32, 44.1, 48 kHz
• File search
Playable media
• CD-ROM, CD-R, CD-RW
Forward file search during ¡# play.
Push the Control knob towards [¢] ➡ ¡$
• Folder search
•
•
CD-RW discs which are quick formatted by the writing
software cannot be used.
When recording to the maximum media capacity at
once, the writing software is set to "Disc at once".
Forward folder search during ¡" play.
Push the Control knob towards [FM] ➡ 3, 4...
• Folder select
When the selection is set to directory 4, and you
want to skip to the folder 2 at the same level.
Push the Control knob towards [4] ➡ 2
When the selection is set to directory 3, moves
the level up by folder select.
Playable disc format
• ISO 9660 Level 1/2
• Joliet
• Romeo
Push the Control knob towards [AM] ➡ 2
• Long file name.
|
6
English
About CDs
Handling CDs
• Do not touch the recording surface of the CD.
Removing CDs
When removing CDs from this unit pull them out
horizontally.
CDs that cannot be used
• CDs that are not round cannot be used.
• CD-R and CD-RW are easier to damage than a
normal music CD. Use a CD-R or a CD-RW after
reading the caution items on the package etc.
• Do not stick tape etc. on the CD, or use a CD with
tape stuck on it.
• CDs with coloring on the recording surface or CDs
that are dirty cannot be used.
• This unit can only play the CDs with
When using a new CD
If the CD center hole or outside rim has burrs,
use the CD only after removing the burrs with a
ballpoint pen, etc.
.
This unit may not correctly play discs which do
not have the mark.
• You cannot play a CD-R or CD-RW that has not
been finalized. (For the finalization process refer to
your CD-R/CD-RW writing software, and your CD-
R/CD-RW recorder instruction manual.)
Burrs
CD storage
Burrs
• Do not place CDs in direct sunlight (On the seat
or dashboard etc.) or where the temperature is
high.
• Store CDs in their cases.
CD accessories
Do not use disc type accessories.
CD cleaning
Clean from the center of the disc and move
outward.
|
English
7
General features
Release button
Control knob
VOL
ATT/DIM
Q
SRC
LOUD indicator
Clock display
ATT indicator
The time until full power OFF can be set in <Power
OFF Timer> (page 25).
Power
Turning ON the Power
Press the [SRC] button.
Turning OFF the Power
Press the [SRC] button for at least 1 second.
Volume
Increasing Volume
Turn the [VOL] knob clockwise.
Selecting the Source
Decreasing Volume
Turn the [VOL] knob counterclockwise.
Press the [SRC] button.
Source required
Tuner
CD
Display
"TUNER"
"CD"
Attenuator
Turning the volume down quickly.
External disc* (Optional accessory)
Auxiliary input*
Standby (Illumination only mode)
"CD CH"
"AUX EXT"
"STANDBY"
Press the [ATT] button.
Each time you press the button, the Attenuator
turns ON and OFF.
When the Attenuator is ON, the "ATT" indicator
blinks.
•
•
* Function of the KDC-W4534
This unit automatically turns full power OFF after 20
minutes lapses in Standby mode in order to save the
vehicle's battery.
|
8
English
System Q
Adjustment Item Display
Range
Bass level
Middle level
Treble level
Balance
"BAS L"
"MID L"
"TRE L"
"BAL"
–8 — +8
–8 — +8
–8 — +8
Left 15 — Right 15
Rear 15 — Front 15
Selecting the best sound setting preset for
different types of music.
1 Select the source to set
Press the [SRC] button.
Fader
"FAD"
Exit Audio Control mode (Volume control mode)
2 Select the Sound type
Press the [Q] button.
5 Exit Audio Control mode
Press any button.
Press a button other than the [VOL] knob, [SRC],
[0] and [ATT] button.
When you press the button once, the current
sound setting is displayed.
Each time you press the button, the sound
setting alternates.
Sound setting
Natural
Rock
Display
"NATURAL"
"ROCK"
"POPS"
Pops
Audio Setup
Easy
"EASY"
Top 40
Jazz
"TOP40"
"JAZZ"
Setting the Sound system, such as Volume offset
and Loudness.
1 Select the source to adjust
Press the [SRC] button.
•
•
Change each setting value with the <Speaker
Setting> (page 10).
First, select the speaker type with the Speaker setting.
When the value is set up by <Audio Control> (page 9),
"USER" is displayed.
2 Enter Audio Setup mode
Press the [VOL] knob for at least 1 second.
3 Select the Audio Setup item to adjust
Press the [VOL] knob.
Each time you press the knob, the item to be
adjusted alternates between the items shown in
the table below.
Audio Control
4 Adjust the Audio setup item
Turn the [VOL] knob.
1 Select the source to adjust
Press the [SRC] button.
Adjustment Item Display
Range
–8 —
ON/OFF
Volume offset
Loudness
"V-OFF"
"LOUD"
0
2 Enter Audio Control mode
Press the [VOL] knob.
3 Select the Audio item to adjust
Press the [VOL] knob.
Each time you press the knob, the item to be
adjusted alternates between the items shown in
the table below.
•
•
Volume offset: Sets each source’s volume as a
difference from the basic volume.
Loudness: Compensates for low and high tones
during low volume.
When Loudness is ON, "LOUD" indicator
is ON.
4 Adjust the Audio item
Turn the [VOL] knob.
5 Exit Audio Setup mode
Press the [VOL] knob for at least 1 second.
|
English
9
General features
In CD & External disc source
Speaker Setting
Information
Display
"D-TITLE"*
Fine-tuning so that the System Q value is optimal
when setting the speaker type.
Disc title (In External disc source or KDC-
W4534/W4034A/W4034AY/W4034G/
W4034GY/W434A/W434G/W410A/W410AY/
W410G/W410GY/W40G/W434GY internal
CD source)
1 Enter Standby
Press the [SRC] button.
Select the "STANDBY" display.
"T-TITLE"*
Track title (In External disc source or KDC-
W4534/W4034A/W4034AY/W4034G/
W4034GY/W434A/W434G/W410A/W410AY/
W410G/W410GY/W40G/W434GY internal
CD source)
Track number & Play time
Clock
2 Enter Speaker Setting mode
Press the [VOL] knob.
3 Select the Speaker type
Turn the [VOL] knob.
Each time you turn the knob, the setting
alternates between the settings shown in the
table below.
"P-TIME"
"CLOCK"
In Audio file source
Speaker type
OFF
For 5 & 4 in. speaker
For 6 & 6x9 in. speaker
For the OEM speaker
Display
Information
Display
"TITLE"*
"ALBUM"*
"FOLDER"
"FILE"
"SP OFF"
"SP 5/4"
"SP 6*9/6"
"SP OEM"
Song title & Artist name
Album name & Artist name
Folder name
File name
Track number & Play time
Clock
"P-TIME"
"CLOCK"
4 Exit Speaker Setting mode
Press the [VOL] knob.
In Standby/ Auxiliary input source
Switching Display
Information
Source name
Clock
Display
"SRC NAME"
"CLOCK"
Changing the information displayed.
1 Enter Switching Display mode
Press the Control knob for at least 1 second.
"DISP SEL" is displayed.
3 Exit Switching Display mode
Press the Control knob.
2 Select the Display item
Push the Control knob towards [4] or
[¢].
•
•
* If the contents of the information cannot be
displayed, Play time is displayed.
Album name cannot be displayed in WMA file.
In Tuner source (KDC-W434A/W434G/
W434GY/W40G)
Information
Frequency
Clock
Display
"FREQ"
"CLOCK"
In Tuner source
Information
Display
Program Service name or Frequency "FREQ/PS"
(FM)
Radio text, Program Service name or "R-TEXT"
Frequency (FM) (KDC-W4534 only)
Frequency (MW, LW)
Clock
"FREQ"
"CLOCK"
|
10
English
Dimmer Control
TEL Mute
You can lower the brightness of the display by
using the dimmer function.
The audio system automatically mutes when a
call comes in.
Press the [DIM] button for at least 1 second.
When a call comes in
"CALL" is displayed.
The audio system pauses.
Each time you press the button for 1 second, the
Dimmer contol turns ON or OFF.
When the Dimmer control is ON, "DIM ON" is
displayed.
Listening to the audio during a call
Press the [SRC] button.
The "CALL" display disappears and the audio
system comes back ON.
When the call ends
Hang up the phone.
The "CALL" display disappears and the audio
system comes back ON.
Theft Deterrent Faceplate
The faceplate of the unit can be detached and
taken with you, helping to deter theft.
Removing the Faceplate
•
To use the TEL Mute feature, you need to hook up
the MUTE wire to your telephone using a commercial
telephone accessory. Refer to <Connection Wires to
Terminals> (page 27).
Press the Release button.
The faceplate unlocks, allowing you to detach it.
•
•
•
The faceplate is a precision piece of equipment and
can be damaged by shocks or jolts.
Keep the faceplate in its faceplate case while
detached.
Do not expose the faceplate (and the faceplate case)
to direct sunlight or excessive heat or humidity. Also
avoid places with too much dust or the possibility of
water splashing.
Reattaching the Faceplate
1 Align the projections on the unit with the
grooves on the faceplate.
Projections
Grooves
2 Push the faceplate in until it clicks.
The faceplate is locked in place, allowing you to
use the unit.
|
English
11
Tuner features
AUTO/
AME
1 - 6
SRC
Control knob
ST indicator
Band display
Frequency display Preset station number
Function of the KDC-W434A/G/KDC-W40G/KDC-
W434GY
Tuning
Selecting the station.
Tuning Mode
1 Select tuner source
Press the [SRC] button.
Select the "TUNER" display.
Choose the tuning mode.
Press the [AUTO] button.
Each time you press the button, the Tuning
mode alternates between the modes shown in
the table below.
2 Select the band
Push the Control knob towards [FM] or [AM].
Each time you push the knob toward [FM], it
switches between the FM1, FM2, and FM3 bands.
Tuning mode
Display
Operation
Automatic search for a station.
Auto seek
"AUTO 1"
Preset station seek "AUTO 2"
Search in order of the stations
in the Preset memory.
3 Tune up or down band
Push the Control knob towards [4] or
[¢].
Manual
"MANUAL" Normal manual tuning control.
•
During reception of stereo stations the "ST" indicator
is ON.
|
12
English
Station Preset Memory
Putting a station in the memory.
1 Select the band
Push the Control knob towards [FM] or [AM].
2 Select the frequency to put in the memory
Push the Control knob towards [4] or
[¢].
3 Put the frequency in the memory
Press the desired [1] — [6] button for at least
2 seconds.
The preset number display blinks 1 time.
On each band, 1 station can be put in the
memory on each [1] — [6] button.
Auto Memory Entry
Putting stations with good reception in the
memory automatically.
1 Select the band for Auto Memory Entry
Push the Control knob towards [FM] or [AM].
2 Open Auto Memory Entry
Press the [AME] button for at least 2 seconds.
When 6 stations that can be received are put in
the memory Auto Memory Entry closes.
•
•
When the <AF (Alternative Frequency)> (page 23) is
ON, only RDS stations are put in the memory.
When Auto Memory Entry is done in the FM2 band,
the RDS stations preset in the FM1 band are not put in
the memory.
Likewise, when Auto Memory Entry is done in the FM3
band, RDS stations preset in FM1 or FM2 are not put
in the memory.
Preset Tuning
Recalling the stations in the memory.
1 Select the band
Push the Control knob towards [FM] or [AM].
2 Recall the station
Press the desired [1] — [6] button.
|
English
13
Function of the KDC-W4534/KDC-W4034A/AY/G/GY/KDC-3034A/G/KDC-W410A/AY/G/GY
RDS features
Control knob
5*
1 - 6
SRC
PTY indicator
TI indicator
Receiving other traffic information stations
Push the Control knob towards [4] or
[¢].
Traffic Information
Changing to traffic information automatically
when a traffic bulletin starts even when you are
not listening to the radio.
•
Traffic information can be switched when it is on the
Tuner Source. However, you cannot switch the Traffic
information during reception of the Traffic bulletin
switched from the source other than the Tuner.
Press the [TI] button.
Each time you press the button, the Traffic
information function turns ON and OFF.
When traffic information is ON, "TI" indicator is
ON.
When a traffic information station is not being
received the "TI" indicator blinks.
When a traffic bulletin starts, "TRAFFIC" is
displayed and the audio changes to traffic
information.
Function of the KDC-W4534
Radio Text Scroll
Scrolling the displayed radio text.
Hold down on [FM] of the Control knob for at
least 2 seconds.
•
•
During reception of an AM station when the Traffic
Information function is turned ON, the frequency
changes to an FM station.
During reception of traffic information the adjusted
volume is automatically remembered, and the next
time the audio changes to traffic information, the
volume automatically becomes the remembered
volume.
|
14
English
PTY (Program Type)
Selecting the Program Type and searching for a
station.
•
Speech and Music include the Program type shown
below.
Music: No.12 — 17, 26 — 30
Speech: No.3 — 11, 18 — 25, 31
You can put the Program Type in the [1] — [6] button
memory and for quick recall. Refer to the <Program
Type preset> (page 15).
You can change the display language. Refer to
<Changing Language for PTY Function> (page 16).
1 Enter PTY mode
Press the Control knob.
•
•
During PTY mode the "PTY" indicator is ON.
•
This function cannot be used during a traffic bulletin
or AM reception.
3 Search for the selected Program Type
station
Push the Control knob towards [4] or
[¢].
When you want to search for other stations, push
[4] or [¢] of the Control knob again.
2 Select the Program Type
Push the Control knob towards [FM] or [AM].
Each time you push the knob, the Program Type
alternates between the program types shown in
the table below.
No.
1.
Program Type
Speech
Display
"SPEECH"
"MUSIC"
"NEWS"
"AFFAIRS"
"INFO"
•
When the selected Program Type is not found, "NO
PTY" is displayed. Select another Program Type.
2.
Music
3.
News
4 Exit PTY mode
Press the Control knob.
4.
5.
6.
Current Affairs
Information
Sport
"SPORT"
7.
8.
9.
Education
Drama
Culture
Science
Varied
Pop Music
Rock Music
Easy Listening Music
Light Classical
Serious Classical
Other Music
Weather
"EDUCATE"
"DRAMA"
"CULTURE"
"SCIENCE"
"VARIED"
"POP M"
"ROCK M"
"EASY M"
"LIGHT M"
"CLASSICS"
"OTHER M"
"WEATHER"
"FINANCE"
"CHILDREN"
"SOCIAL"
"RELIGION"
"PHONE IN"
"TRAVEL"
"LEISURE"
"JAZZ"
"COUNTRY"
"NATION M"
"OLDIES"
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
Program Type preset
Putting the Program Type in the Preset button
memory and quick recall.
Presetting the Program Type
1 Select the Program Type to preset
Refer to <PTY (Program Type)> (page 15).
2 Preset the Program Type
Press the desired [1] — [6] button for at least
2 seconds.
Finance
Children’s programs
Social Affairs
Religion
Phone In
Travel
Recalling the preset Program Type
1 Enter PTY mode
Refer to <PTY (Program Type)> (page 15).
Leisure
2 Recall the Program Type
Press the desired [1] — [6] button.
Jazz Music
Country Music
National Music
Oldies Music
Folk Music
Documentary
"FOLK M"
"DOCUMENT"
|
English
15
Function of the KDC-W4534/KDC-W4034A/AY/G/GY/KDC-3034A/G/KDC-W410A/AY/G/GY
RDS features
Changing Language for PTY
Function
Selecting the Program Type display language.
1 Enter PTY mode
Refer to <PTY (Program Type)> (page 15).
2 Enter Changing Language mode
Press the [TI] button.
3 Select the language
Push the Control knob towards [FM] or [AM].
Each time you push the knob, the language
alternates between the languages shown in the
table below.
Language
English
French
Display
"ENGLISH"
"FRENCH"
"GERMAN"
German
4 Exit Changing Language mode
Press the [TI] button.
|
16
English
CD/Audio file/External disc control features
0
SCAN RDM/ REP F.SEL M.RDM
3
Control knob
SRC
Disc number
IN indicator
Track number
Play time
Function of the KDC-W4534
Playing CD & Audio file
Playing External Disc
When a disc is inserted
Press the [SRC] button.
Select the "CD" display.
Playing discs set in the optional accessory disc
player connected to this unit.
Press the [SRC] button.
Select the display for the disc player you want.
Display examples:
•
When a CD is inserted, the "IN" indicator is ON.
Pause and play
Display
"CD CH"
"MD CH"
Disc player
CD changer
MD changer
Press the Control knob.
Each time you press the knob, the audio pauses
or plays.
Pause and play
Eject the CD
Press the Control knob.
Each time you press the knob, the audio pauses
or plays.
Press the [0] button.
•
Refer to <About MP3 and WMA> (page 6) for the
Audio file by models you can play.
•
•
Disc 10 is displayed as "0".
The functions that can be used and the information
that can be displayed will differ depending on the
external disc players being connected.
|
English
17
CD/Audio file/External disc control features
Fast Forwarding and Reversing
Track/File/Disc/Folder Repeat
Replaying the song, disc in the Disc changer or
Audio file folder you are listening to.
Fast Forwarding
Hold down toward [¢] with the Control
knob.
Press the [REP] button.
Each time you press the button, the Repeat Play
alternates between the modes shown in the
tables below.
Release your finger to play the disc at that point.
Reversing
Hold down toward [4] with the Control
knob.
In CD & External disc source
Release your finger to play the disc at that point.
Repeat play
Track Repeat
Disc Repeat (In Disc Changer)
OFF
Display
"TRAC REP"
"DISC REP"
"REP OFF"
•
There is no sound while the Audio file is being
searched.
In Audio file source
Repeat play
File Repeat
Folder Repeat
OFF
Display
"FILE REP"
"FOLD REP"
"REP OFF"
Track/File Search
Searching for a song on the disc or in the Audio
file folder.
Push the Control knob towards [4] or
[¢].
Scan Play
Playing the first part of each song on the disc
or Audio file folder you are listening to and
searching for the song you want to hear.
Function of the KDC-W4534/KDC-W4034A/AY/G/
GY/KDC-W434A/G/KDC-W410A/AY/G/GY/KDC-
W40G/KDC-W434GY
1 Start Scan Play
Press the [SCAN] button.
"TRAC SCN"/"FILE SCN" is displayed.
Function of disc changer/ Audio file
Disc Search/Folder Search
Selecting the disc set in the Disc changer or the
folder recorded on the Audio file media.
2 Release it when the song you want to hear is
played
Press the [SCAN] button.
Push the Control knob towards [FM] or [AM].
Random Play
Playing all the songs on the disc in random order.
Press the [RDM] button.
Each time you press the button, Random Play
turns ON or OFF.
When the Random mode is ON, "DISC RDM"/
"FOLD RDM" is displayed.
•
When you push the Control knob toward [¢], the
next random song starts.
|
18
English
Function of the KDC-W4534
Function of disc changer
3 Decide the folder to play
Press the Control knob.
Magazine Random Play
The Folder Select mode releases, and the Audio
file in the folder being displayed plays.
Play the songs on all the discs in the disc changer
in random order.
Cancelling the Folder Select mode
Press the [F.SEL] button.
Press the [M.RDM] button.
Each time you press the button, the Magazine
Random Play turns ON or OFF.
When the Magazine Random mode is ON,
"MGZN RDM" is displayed.
Function of the KDC-W4534/KDC-W4034A/AY/G/
GY/KDC-W434A/G/KDC-W410A/AY/G/GY/KDC-
W40G/KDC-W434GY
•
When you push the Control knob toward [¢], the
next random song starts.
Text/Title Scroll
Scrolling the displayed CD text, Audio file text, or
MD title.
Push the Control knob toward [FM] for at
least 2 seconds.
Function of the KDC-W4534/KDC-W4034A/AY/G/
GY/KDC-W434A/G/KDC-W410A/AY/G/GY/KDC-
W40G/KDC-W434GY
Function of Audio file
Folder Select
Quickly selecting the folder you want to hear.
1 Enter Folder Select mode
Press the [F.SEL] button.
"FOLD SEL" is displayed.
During Select mode the folder information is
displayed as shown below.
Folder name display
Displays the current folder name.
2 Select the folder level
Push the Control knob towards [FM] or [AM].
With the [FM] of the Control knob, you move
1 level down and with the [AM] of the Control
knob, 1 level up.
Selecting a folder in the same level
Push the Control knob towards [4] or
[¢].
With the [4] of the Control knob, you move
to the previous folder, and with the [¢] of the
Control knob, to the next folder.
Returning to the top level
Press the [3] button.
|
English
19
Menu system
Control knob
MENU
SRC
RDS indicator
Menu display
You can continue by returning to step 2 and
setting other items.
Menu System
Setting beep sound during operation, etc.
functions.
The Menu system basic operation method is
explained here. The reference for the Menu items
and their setting content is after this operation
explanation.
4 Exit Menu mode
Press the [MENU] button.
•
When other items those applicable to the basic
operation method above are displayed, their setting
content chart is entered. (Normally the setting listed at
the top of the chart is the original setting.)
Also, the explanation for items that are not applicable
(<Manual Clock Adjustment> etc.) are entered step
by step.
1 Enter Menu mode
Press the [MENU] button for at least 1 second.
"MENU" is displayed.
2 Select the menu item
Push the Control knob towards [FM] or [AM].
Example: When you want to set the beep sound,
select the "BEEP" display.
3 Set the menu item
Push the Control knob towards [4] or
[¢].
Example: When you select "BEEP", each time you
push the knob it alternates between
"BEEP ON" or "BEEP OFF". Select 1 of
them as the setting.
|
20
English
Function of the KDC-W4534
In Standby mode
•
If you enter a Code different from your Security Code,
you have to start over from step 4.
Security Code
Activating the Security Code disables the usage
of audio unit by someone else. Once the Security
Code is activated, the entry of authorized Security
Code is required to turn on the audio unit when
it is removed from the vehicle. Indication of this
Security Code activation prevents your precious
audio unit from stealing.
Resetting the Security Code function when
the audio unit is first used after removed
from the battery power source or the Reset
button is pressed
1 Turn the power ON.
2 Do the step 4 through 7 step operation, and
reenter the security code.
"APPROVED" is displayed.
Now, you can use the unit.
•
•
Set the Security Code when the <Demonstration mode
Setting> (page 25) is set to OFF.
When you activate the Security Code function, it cannot
be released.
Note, your Security Code is the 4 digit number entered in
your "Car Audio Passport" in this package.
•
If an incorrect code is entered, "WAITING" is displayed,
and the input prohibition periods shown in the table
below is generated.
After the input prohibition time lapses, "CODE" is
displayed, and you can reenter the code.
1 Enter Standby
Press the [SRC] button.
Select the "STANDBY" display.
Number of times the
Input prohibited time
incorrect code was input
2 Enter Menu mode
1
2
3
4
—
5 minutes
1 hour
Press the [MENU] button for at least 1 second.
When "MENU" is displayed, "CODE SET" is
displayed.
24 hours
3 Enter Security Code mode
Press the Control knob for at least 2 seconds.
When "ENTER" is displayed, "CODE" is also
displayed.
In Standby mode
Touch Sensor Tone
4 Select the digits to enter
Push the Control knob towards [4] or
[¢].
Setting the operation check sound (beep sound)
ON/OFF.
5 Select the Security Code numbers
Display
"BEEP ON"
"BEEP OFF"
Setting
Beep is heard.
Beep canceled.
Push the Control knob towards [FM] or [AM].
6 Repeat steps 4 and 5, and complete the
Security Code.
7 Confirm the Security Code
Press the Control knob for at least 3 seconds.
When "RE-ENTER" is displayed, "CODE" is also
displayed.
8 Do the step 4 through 7 step operation, and
reenter the security code.
"APPROVED" is displayed.
The Security Code function activates.
|
English
21
Menu system
In Standby mode
Function of the KDC-W4534
Manual Clock Adjustment
Selectable Illumination
Selecting the button illumination color as green
or red.
•
You can do this adjustment when the <Synchronize
Clock> (page 22) is set as OFF.
Display
Setting
"KEY RED"
"KEY GRN"
The illumination color is red.
The illumination color is green.
1 Select Clock Adjustment mode
Push the Control knob towards [FM] or [AM].
Select the "CLK ADJ" display.
2 Enter Clock Adjust mode
Press the Control knob for at least 1 second.
The clock display blinks.
Function of the KDC-W4534/KDC-W4034A/AY/G/
GY/KDC-W434A/G/KDC-W410A/AY/G/GY/KDC-
W40G/KDC-W434GY
3 Adjust the hours
Push the Control knob towards [FM] or [AM].
In CD mode
Supreme Setting
Adjust the minutes
When MP3 or WMA files encoded at a low bit
rate (less than 96kbps (fs=32k, 44.1k, 48kHz))
are played, this function restores their high
frequency region to approach the sound quality
of equivalents of these files encoded at a high bit
rate. Processing is optimized for the compression
format used (MP3, or WMA), and adjustment is
made for the bit rate used.
Push the Control knob towards [4] or
[¢].
4 Exit Clock adjustment mode
Press the [MENU] button.
Function of the KDC-W4534/KDC-W4034A/AY/G/
GY/KDC-3034A/G/KDC-W410A/AY/G/GY
In Standby mode
Display
Setting
"SPRM ON"
"SPRM OFF"
Plays sound using the Supreme function.
Plays the original sound stored in the audio file.
Synchronize Clock
Synchronizing the RDS station time data and this
unit’s clock.
•
The sound effect may be imperceptible depending
on the relationship between the audio file format and
setting.
Display
"SYNC ON"
"SYNC OFF"
Setting
Synchronizes the time.
Adjust the time manually.
•
It takes 3 to 4 minutes to synchronize the clock.
Function of the KDC-W4534/KDC-W4034A/AY/G/
GY/KDC-3034A/G/KDC-W410A/AY/G/GY
DSI (Disabled System Indicator)
A red indicator will blink on the unit after the
faceplate is removed, warning potential thieves.
Display
"DSI ON"
"DSI OFF"
Setting
LED flashes.
LED OFF.
|
22
English
Function of the KDC-W4534/KDC-W4034A/AY/G/
GY/KDC-3034A/G/KDC-W410A/AY/G/GY
Function of the KDC-W4534/KDC-W4034A/AY/G/
GY/KDC-3034A/G/KDC-W410A/AY/G/GY
In Tuner mode
News Bulletin with Timeout Setting
Tuning Mode
The tuner automatically changes when a news
bulletin starts even if the radio is not being
listened to. Also, you can set the time interval
when interruption is prohibited.
Sets the tuning mode.
Tuning mode
Display
Operation
Auto seek
"AUTO 1"
Automatic search for a station.
Preset station seek "AUTO 2"
Search in order of the stations
in the Preset memory.
Display and Setting
"NEWS OFF"
"NEWS 00M"
Manual
"MANUAL" Normal manual tuning control.
"NEWS 90M"
Function of the KDC-W4534/KDC-W4034A/AY/G/
GY/KDC-3034A/G/KDC-W410A/AY/G/GY
When you set "NEWS 00M" — "NEWS 90M", the
News Bulletin Interrupt function is ON.
When the news bulletin starts, "NEWS" is
displayed, and the tuner changes to the news
bulletin.
AF (Alternative Frequency)
When the reception is poor, automatically
alternate to another frequency broadcasting the
same program in the same RDS network with
better reception.
•
If you choose the "20MIN" setting, further news
bulletins will not be received for 20 minutes once the
first news bulletin is received.
Display
"AF ON"
"AF OFF"
Setting
The AF function is ON.
The AF function is OFF.
•
•
The news bulletin volume is the same level that was
set for <Traffic Information> (page 14).
This news bulletin function is only available if the
desired station sends PTY-code for news bulletin or
belongs to <Enhanced Other Network>-Network
sending PTY-code for news bulletin.
When the AF function is ON, the "RDS" indicator
is ON.
•
When no other stations with stronger reception are
available for the same program in the RDS network,
you may hear the incoming broadcast in bits and
snatches. Turn OFF the AF function in such a case.
•
When the News Bulletin Interrupt function is ON, the
tuner changes to an FM station.
In Tuner mode
Local Seek
Function of the KDC-W4534/KDC-W4034A/AY/G/
GY/KDC-3034A/G/KDC-W410A/AY/G/GY
Only stations whose reception is good are
searched in auto seek tuning.
Restricting RDS Region (Region
Restrict Function)
Display
Setting
"LO.S OFF"
"LO.S ON"
The local seek function is OFF.
The local seek function is ON.
You can choose whether or not to restrict the
RDS channels, received with the AF function for a
particular network, to a specific region.
Display
Setting
"REG ON"
"REG OFF"
The Region Restrict Function is ON.
The Region Restrict Function is OFF.
•
If AF function is not restricted to the specified region
and network, the AF function sets up to search the
station with good reception in the same RDS network.
|
English
23
Menu system
Function of the KDC-W4534/KDC-W4034A/AY/G/
GY/KDC-3034A/G/KDC-W410A/AY/G/GY
Each time you push the knob, the display
alternates as listed below.
• "AUX EXT"
• "DVD"
• "PORTABLE"
• "GAME"
Auto TP Seek
When the TI function is ON and the reception
is poor while listening to a traffic information
station, another traffic information station
with better reception will be searched for
automatically.
• "VIDEO"
• "TV"
6 Exit Auxiliary input display setting mode
Press the [MENU] button.
Display
"ATPS ON"
"ATPS OFF"
Setting
The Auto TP Seek Function is ON.
The Auto TP Seek Function is OFF.
•
When operation stops for 10 seconds, the name at
that time is registered, and the Auxiliary input display
setting mode closes.
In FM reception
Monaural Reception
You can reduce the noise when stereo broadcasts
are received as monaural.
Function of the KDC-W4534/KDC-W4034A/AY/G/
GY/KDC-W434A/G/KDC-W410A/AY/G/GY/KDC-
W40G/KDC-W434GY
Display
Setting
Text Scroll
"MONO OFF"
"MONO ON"
The monaural reception is OFF.
The monaural reception is ON.
Setting the displayed text scroll.
Display
Setting
"SCL MANU"
"SCL AUTO"
Doesn’t scroll.
Scrolls when the display changes.
Function of the KDC-W4534
Auxiliary Input Display Setting
•
The text scrolled is listed below.
- CD text
- Folder name/ File name/ Song title/ Artist name/
Selecting the display when alternating to
Auxiliary input source.
Album name
- MD title
- Radio text
1 Select Auxiliary input source
Press the [SRC] button.
Select the "AUX EXT" display.
2 Enter Menu mode
Press the [MENU] button for at least 1 second.
"MENU" is displayed.
3 Select Auxiliary input display setting mode
Push the Control knob towards [FM] or [AM].
Select the "NAME SET" display.
4 Enter Auxiliary input display setting mode
Press the Control knob for at least 1 second.
The selected Auxiliary input display is displayed.
5 Select the Auxiliary input display
Push the Control knob towards [4] or
[¢].
|
24
English
In Standby mode
Function of the KDC-W4534
In Standby mode
Power OFF Timer
Demonstration mode Setting
Setting the timer to turn this unit’s power OFF
automatically when Standby mode continues.
Using this setting can save the vehicle’s battery
power.
Sets the demonstration mode.
1 Select the Demonstration mode
Push the Control knob towards [FM] or [AM].
Select the "DEMO" display.
Display
Setting
"OFF – – –"
"OFF 20M"
(Original setting)
"OFF 40M"
"OFF 60M"
Power OFF Timer function is OFF.
Turns the power OFF after 20 minutes.
2 Set the Demonstration mode
Press the Control knob for at least 2 seconds.
Each time you press the knob at least 2 seconds,
the Demonstration mode alternates between the
settings shown in the table below.
Turns the power OFF after 40 minutes.
Turns the power OFF after 60 minutes.
Display
Setting
"DEMO ON"
"DEMO OFF"
The Demonstration mode function is ON.
Exit Demonstration mode (Normal mode).
•
Do this setting after setting <Security Code> (page
21).
Function of the KDC-W4534/KDC-W4034A/AY/G/
GY/KDC-W434A/G/KDC-W410A/AY/G/GY/KDC-
W40G/KDC-W434GY
In Standby mode
CD Read Setting
When there is a problem with playing a CD with
special format, this setting plays the CD by force.
Display
Setting
"CD READ1"
"CD READ2"
Play CD and Audio file.
Play CD by force.
•
Setting "CD READ2" cannot play Audio file.
Some music CDs may not play even in the "CD
READ2" mode.
|
English
25
Accessories/ Installation Procedure
Accessories
•
If the power is not turned ON (or it is ON, but will be OFF
immediately), the speaker wire may have a short-circuit
or touched the chasis of the vehicle and the protection
function may have been activated. Therefore, the speaker
wire should be checked.
1
..........1
•
If your car is not prepared for this special connection-
system, consult your Kenwood dealer.
•
Only use antenna conversion adaptors (ISO-JASO) when
the antenna cord has an ISO plug.
2
•
Make sure that all wire connections are securely made by
inserting jacks until they lock completely.
..........2
•
If your vehicle’s ignition does not have an ACC position,
or if the ignition wire is connected to a power source
with constant voltage such as a battery wire, the power
will not be linked with the ignition (i.e., it will not turn on
and off along with the ignition). If you want to link the
unit’s power with the ignition, connect the ignition wire
to a power source that can be turned on and off with the
ignition key.
3
..........1
4
•
•
If the fuse blows, first make sure that the wires have not
caused a short circuit, then replace the old fuse with one
with the same rating.
Insulate unconnected wires with vinyl tape or other
similar material. To prevent short circuits, also do not
remove the caps on the ends of the unconnected wires
or the terminals.
Connect the speaker wires correctly to the terminals to
which they correspond. The unit may receive damage or
fail to work if you share the - wires and/or ground them
to any metal part in the car.
After the unit is installed, check whether the brake lamps,
indicators, wipers, etc. on the car are working properly.
If the console has a lid, make sure to install the unit so
that the faceplate does not hit the lid when closing and
opening.
(KDC-W4534 only) ..........1
Installation Procedure
•
1. To prevent short circuits, remove the key from
the ignition and disconnect the - terminal of
the battery.
2. Make the proper input and output wire
connections for each unit.
•
•
3. Connect the wire on the wiring harness.
4. Take Connector B on the wiring harness and
connect it to the speaker connector in your
vehicle.
•
Mount the unit so that the mounting angle is 30° or less.
5. Take Connector A on the wiring harness and
connect it to the external power connector on
your vehicle.
6. Connect the wiring harness connector to the
unit.
7. Install the unit in your car.
8. Reconnect the - terminal of the battery.
9. Press the reset button.
|
26
English
Connecting Wires to Terminals
KDC-W4534
KDC-W4034A/W4034AY/ KDC-W434A/
W4034G/W4034GY/
W434G/W434GY/
W410A/W410AY/W410G/ W40G
W410GY/3034A/3034G
A
B
To Steering remote
To Kenwood disc changer/
External optional accessory
Rear left output (White)/
Rear right output (Red)
To Steering remote
—
—
—
REMO. CONT
A
C
Rear left output (White)/
Rear right output (Red)
—
To connect these leads, refer to the relevant
instruction manuals.
C
B
FM/AM antenna input
Antenna Cord (ISO)
Antenna Conversion Adaptor
(ISO–JASO) (Accessory3)
Fuse (10A)
To external audio unit
(Portable Audio, etc.)
Wiring harness
(Accessory1)
AUX Input adaptor
(Accessory4)
Connect to the terminal that
TEL mute wire (Brown)
is grounded when either the
telephone rings or during
conversation.
MUTE
To connect the Kenwood
navigation system, consult
your navigation manual.
If no connections are made, do
not let the wire come out from
the tab.
Power control/ Motor
antenna control wire
(Blue/White)
Connect either to the power
control terminal when using the
optional power amplifier, or to
the antenna control terminal in
the vehicle.
P.CONT
ANT.CONT
Battery wire (Yellow)
Ignition wire (Red)
See next page.
A–7 Pin (Red)
A–4 Pin (Yellow)
Connector A
Connector B
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
English
|
27
Connecting Wires to Terminals
Connector Function Guide
Pin Numbers for Cable Colour
ISO Connectors
External Power
Connector
2WARNING
Connecting the ISO Connector
The pin arrangement for the ISO connectors depends
on the type of vehicle you drive. Make sure to make the
proper connections to prevent damage to the unit.
The default connection for the wiring harness is described
in 1 below. If the ISO connector pins are set as described
in 2 or 3, make the connection as illustrated.
Functions
A-4
A-5
A-7
A-8
Yellow
Blue/White
Red
Battery
Power Control
Ignition (ACC)
Earth (Ground)
Connection
Black
Please be sure to reconnect the cable as shown 2 below
to install this unit to the Volkswagen vehicles etc.
Speaker
Connector
B-1
B-2
B-3
B-4
B-5
B-6
B-7
B-8
Purple
Purple/Black
Gray
Gray/Black
White
White/Black
Green
Rear Right (+)
Rear Right (–)
Front Right (+)
Front Right (–)
Front Left (+)
Front Left (–)
Rear Left (+)
Rear Left (–)
1(Default setting) The A-7 pin (red) of the vehicle’s
ISO connector is linked with the ignition, and
the A-4 pin (yellow) is connected to the constant
power supply.
Ignition cable (Red)
Unit
Battery cable (Yellow)
A-7 Pin (Red)
Vehicle
A-4 Pin (Yellow)
Green/Black
2The A-7 pin (red) of the vehicle’s ISO connector
is connected to the constant power supply, and
the A-4 pin (yellow) is linked to the ignition.
A-7 Pin (Red)
Ignition cable (Red)
Unit
Vehicle
A-4 Pin (Yellow)
Battery cable (Yellow)
3The A-4 pin (yellow) of the vehicle’s ISO
connector is not connected to anything, while
the A-7 pin (red) is connected to the constant
power supply (or both the A-7 (red) and A-4
(yellow) pins are connected to the constant
power supply).
Ignition cable (Red)
Unit
Battery cable (Yellow)
A-7 Pin (Red)
Vehicle
A-4 Pin (Yellow)
•
When the connection is made as in 3 above, the unit’s
power will not be linked to the ignition key. For that
reason, always make sure to turn off the unit’s power
when the ignition is turned off.
To link the unit’s power to the ignition, connect the
ignition cable (ACC...red) to a power source that can be
turned on and off with the ignition key.
|
28
English
Installation
Installation
Metal mounting strap
(commercially available)
Firewall or metal support
Bend the tabs of the
mounting sleeve with a
screwdriver or similar utensil
and attach it in place.
Self-tapping screw
(commercially available)
Screw (M4X8)
(commercially available)
•
Make sure that the unit is installed securely in place. If
the unit is unstable, it may malfunction (for example, the
sound may skip).
English
|
29
Removing the Unit
Removing the hard rubber frame
Removing the Unit
1 Engage the catch pins on the removal tool and
remove the two locks on the upper level.
Upper the frame and pull it forward as shown in
the figure.
1 Refer to the section <Removing the hard rubber
frame> (page 30) and then remove the hard
rubber frame.
2 Remove the screw (M4 × 8) on the back panel.
3 Insert the two removal tools deeply into the slots
on each side, as shown.
Screw (M4X8)
(commercially available)
Lock
Catch
Accessory2
Removal tool
2 When the upper level is removed, remove the
lower two locations.
Accessory2
Removal tool
4 Lower the removal tool toward the bottom, and
pull out the unit halfway while pressing towards
the inside.
•
The frame can be removed from the bottom side in the
same manner.
•
Be careful to avoid injury from the catch pins on the
removal tool.
5 Pull the unit all the way out with your hands,
being careful not to drop it.
|
30
English
Troubleshooting Guide
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
? Even if Loudness is turned ON, high-pitched tone
isn’t compensated for.
✔
Tuner source is selected.
☞
High-pitched tone isn’t compensated for when
in Tuner source.
? No sound can be heard, or the volume is low.
General
✔
The fader or balance settings are set all the way to
one side.
? The power does not turn ON.
☞
Center the fader and balance settings.
✔
The fuse has blown.
✔
The input/output wires or wiring harness are
connected incorrectly.
☞
After checking for short circuits in the wires,
replace the fuse with one with the same
rating.
☞
Reconnect the input/output wires or the
wiring harness correctly. See the section on
<Connecting Wires to Terminals>.
? There’s a source you can’t switch.
✔
There’s no media inserted.
✔
The values of Volume offset are low.
☞
Set the media you want to listen to. If there’s
no media in this unit, you can’t switch to each
source.
☞
Turn up the Volume offset, referring to the
section on <Audio Setup> (page 9).
? The sound quality is poor or distorted.
✔
The Disc changer isn’t connected.
✔
One of the speaker wires is being pinched by a
screw in the car.
☞
Connect the Disc changer. If the Disc changer
isn’t connected to it’s input terminal, You can’t
switch to an external disc source.
☞
Check the speaker wiring.
✔
The speakers are not wired correctly.
? The memory is erased when the ignition is
turned OFF.
☞
Reconnect the speaker wires so that each
output terminal is connected to a different
speaker.
✔
The ignition and battery wire are incorrectly
connected.
? The Touch Sensor Tone doesn’t sound.
The preout jack is being used.
☞
Connect the wire correctly, referring to the
section on <Connecting Wires to Terminals>.
✔
☞
The Touch Sensor Tone can’t be output from
the preout jack.
? The TEL mute function does not work.
The TEL mute wire is not connected properly.
✔
? Even though Synchronize Clock is ON, the clock
can’t be adjusted.
☞
Connect the wire correctly, referring to the
section on <Connecting Wires to Terminals>.
✔
The received RDS station isn’t sending time data.
? The TEL mute function turns ON even though the
TEL mute wire is not connected.
☞
Receive another RDS station.
✔
The TEL mute wire is touching a metal part of the
Tuner source
car.
☞
Pull the TEL mute wire away from the metal
part of the car.
? Radio reception is poor.
✔
The car antenna is not extended.
☞
Pull the antenna out all the way.
✔
The antenna control wire is not connected.
☞
Connect the wire correctly, referring to the
section on <Connecting Wires to Terminals>.
English
|
31
Troubleshooting Guide
Disc source
Audio file source
? "AUX EXT" is displayed without achieving
? Cannot play an Audio file.
External disc control mode.
✔
The media is scratched or dirty.
✔
Unsupported disc changer is connected.
☞
Clean the media, referring to the CD cleaning
of the section on <About CDs> (page 7).
☞
Use the disc changer mentioned in the
<About CD players/disc changers connected
to this unit> (page 3) of the section on <Safety
precautions>.
? The sound skips when an Audio file is being
played.
✔
The media is scratched or dirty.
? The specified disc does not play, but another one
plays instead.
☞
Clean the media, referring to the CD cleaning
of the section on <About CDs> (page 7).
✔
The specified CD is quite dirty.
✔
The recording condition is bad.
Record the media again or use another media.
☞
Clean the CD.
☞
✔
The disc is loaded in a different slot from that
specified.
? The Audio file track time isn’t displayed correctly.
✔
---
☞
☞
Eject the disc magazine and check the
number for the specified disc.
There are times when it isn’t displayed
correctly according to the Audio file recording
conditions.
✔
The disc is severely scratched.
Try another disc instead.
☞
? Supreme does not take effect when it is turned
ON.
? A CD ejects as soon as it is loaded.
The CD is quite dirty.
✔
✔
Little high-frequency component.
☞
Clean the CD, referring to the CD cleaning of
the section on <About CDs> (page 7).
☞
Supreme would not take effect with songs
with little high-frequency component.
? Can’t remove disc.
The cause is that more than 10 minutes has
✔
Songs that have not been encoded at bit rates
lower than 96 kbps (fs = 32k, 44.1 k, 48 kHz)or
those that have been encoded at a variable bit
rate cannot be decoded to reproduce their high-
frequency components.
✔
elapsed since the vehicle ACC switch was turned
OFF.
☞
The disc can only be removed within 10
minutes of the ACC switch being turned OFF.
If more than 10 minutes has elapsed, turn
the ACC switch ON again and press the Eject
button.
☞
---
? The disc won’t insert.
There’s already another disc inserted.
Press the [0] button and remove the disc.
✔
☞
? Direct Search can’t be done.
Another function is ON.
Turn Random Play or other functions OFF.
✔
☞
? Track Search can’t be done.
For the discs/folders first or last song.
✔
☞
For each disc/folder, Track Search can’t be
done in the backward direction for the first
song or in the forward direction for the last
song.
|
32
English
READING:
IN (Blink):
The unit is reading the data on the disc.
The messages shown below display your
systems condition.
The CD player section is not operating
properly.
EJECT:
No disc magazine has been loaded in
the changer. The disc magazine is not
completely loaded.
➪ Reinsert the CD. If the CD cannot be
ejected or the display continues to flash
even when the CD has been properly
reinserted, please switch off the power
and consult your nearest service center.
➪ Load the disc magazine properly.
No CD in the unit.
➪ Insert the CD.
PROTECT:
NA FILE:
The speaker wire has a short-circuit or
touches the chassis of the vehicle, and
then the protection function is activated.
➪ Wire or insulate the speaker cable
properly and press the reset button.
NO DISC:
TOC ERR:
No disc has been loaded in the disc
magazine.
➪ Load a disc into the disc magazine.
No disc has been loaded in the disc
magazine.
➪ Load a disc into the disc magazine.
The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
➪ Clean the CD and load it correctly.
An Audio file is played with a format that
this unit can’t support.
➪ ----
COPY PRO:
DEMO:
A copy-protected file is played.
➪ ----
E-05:
The CD is upside-down.
➪ Load the CD correctly.
The Demonstration mode has been
selected.
➪ The <Demonstration mode Setting>
(page 25) is ON. Turn it OFF.
BLANK:
Nothing has been recorded on the MD.
NO TRACK:
No tracks are recorded on the MD,
although it has a title.
E-15:
Media was played that doesn’t have data
recorded that the unit can play.
➪ Use media that has data recorded that
the unit can play.
NO PANEL:
E-77:
The faceplate of the slave unit being
connected to this unit has been removed.
➪ Replace it.
The unit is malfunctioning for some reason.
➪ Press the reset button on the unit. If the
"E-77" code does not disappear, consult
your nearest service center.
E-99:
Something is wrong with the disc
magazine. Or the unit is malfunctioning for
some reason.
➪ Check the disc magazine. And then
press the reset button on the unit. If the
"E-99" code does not disappear, consult
your nearest service center.
HOLD:
The protective circuit in the unit activates
when the temperature inside the
automatic disc changer exceeds 60°C
(140°F), stopping all operation.
➪ Cool down the unit by opening
the windows or turning on the air
conditioner. As the temperature falls
below 60°C (140°F), the disc will start
playing again.
LOAD:
Discs are being exchanged in the Disc
changer.
English
|
33
Specifications
Specifications subject to change without notice.
CD player section
Laser diode
: GaAlAs
FM tuner section
Digital filter (D/A)
: 8 Times Over Sampling
Frequency range (50 kHz space)
: 87.5 MHz – 108.0 MHz
D/A Converter
: 1 Bit
Usable sensitivity (S/N = 26dB)
: 0.7 μV /75 Ω
Spindle speed
Quieting Sensitivity (S/N = 46dB)
: 1.6 μV /75 Ω
Frequency response ( 3.0 dB)
: 30 Hz – 15 kHz
Signal to Noise ratio (MONO)
: 65 dB
KDC-W4534/W4034A/W4034AY/W4034G/
W4034GY/W434A/W434G/W434GY/W410A/
W410AY/W410G/W410GY/W40G
: 1000 – 400 rpm (CLV 2times)
KDC-3034A/3034G
: 500 – 200 rpm (CLV)
Wow & Flutter
: Below Measurable Limit
Frequency response ( 1 dB)
: 10 Hz – 20 kHz
Selectivity (DIN) ( 400 kHz)
: ≥ 80 dB
Stereo separation (1 kHz)
: 35 dB
Total harmonic distortion (1 kHz)
: 0.01 %
Signal to Noise ratio (1 kHz)
KDC-W4534/W4034A/W4034AY/W4034G/
W4034GY/W434A/W434G/W434GY/W410A/
W410AY/W410G/W410GY/W40G
MW tuner section
Frequency range (9 kHz space)
: 531 kHz – 1611 kHz
Usable sensitivity (S/N = 20dB)
: 25 μV
: 105 dB
KDC-3034A/3034G
: 93 dB
Dynamic range
: 93 dB
LW tuner section
Frequency range
: 153 kHz – 281 kHz
Usable sensitivity (S/N = 20dB)
: 45 μV
MP3 decode
KDC-W4534/W4034A/W4034AY/W4034G/
W4034GY/W434A/W434G/W434GY/W410A/
W410AY/W410G/W410GY/W40G
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
KDC-W4534/W4034A/W4034AY/W4034G/
W4034GY/W434A/W434G/W434GY/W410A/
W410AY/W410G/W410GY/W40G
: Compliant with Windows Media Audio
|
34
English
Audio section
Maximum output power
KDC-W4534/W4034AY/W4034GY/W434GY/
W410AY/W410GY
: 50 W x 4
KDC-W4034A/W4034G/3034A/3034G/ W434A/
W434G/W410A/W410G/W40G
: 45 W x 4
Output power (DIN 45324, +B=14.4V)
KDC-W4534/W4034AY/W4034GY/W434GY/
W410AY/W410GY
: 30 W x 4
KDC-W4034A/W4034G/3034A/3034G/ W434A/
W434G/W410A/W410G/W40G
: 28 W x 4
Speaker Impedance
: 4 - 8 Ω
Tone action
Bass : 100 Hz 8 dB
Middle : 1 kHz 8 dB
Treble : 10 kHz 8 dB
Preout level / Load (during disc play)
KDC-W4534/W4034A/W4034AY/W4034G/
W4034GY/W410A/W410AY/W410G/W410GY/
3034A/3034G
: 2000 mV/10 kΩ
Preout impedance (during disc play)
KDC-W4534/W4034A/W4034AY/W4034G/
W4034GY/W410A/W410AY/W410G/W410GY/
3034A/3034G
: ≤ 600 Ω
Auxiliary input (Using AUX Input Adaptor)
(KDC-W4534 only)
Frequency response ( 1 dB)
: 20 Hz – 20 kHz
Input Maximum Voltage
: 1200 mV
Input Impedance
: 100 kΩ
General
Operating voltage (11 – 16V allowable)
: 14.4 V
Current consumption
: 10 A
Installation Size (W x H x D)
: 182 x 53 x 155 mm
Weight
: 1.4 kg
English
|
35
|